TL071, TL071A, TL071B, TL072 TL072A, TL072B, TL074, TL074A, TL074B LOW-NOISE JFET-INPUT OPERATIONAL AMPLIFIERS SLOS080D – SEPTEMBER 1978 – REVISED AUGUST 1996 D D D Low Power Consumption Wide Common-Mode and Differential Voltage Ranges Low Input Bias and Offset Currents Output Short-Circuit Protection Low Total Harmonic Distortion 0.003% Typ D D D D D D D D Low Noise Vn = 18 nV/√Hz Typ at f = 1 kHz High Input Impedance . . . JFET Input Stage Internal Frequency Compensation Latch-Up-Free Operation High Slew Rate . . . 13 V/ µs Typ Common-Mode Input Voltage Range Includes VCC + description The JFET-input operational amplifiers in the TL07_ series are designed as low-noise versions of the TL08_ series amplifiers with low input bias and offset currents and fast slew rate. The low harmonic distortion and low noise make the TL07_ series ideally suited for high-fidelity and audio preamplifier applications. Each amplifier features JFET inputs (for high input impedance) coupled with bipolar output stages integrated on a single monolithic chip. The C-suffix devices are characterized for operation from 0°C to 70°C. The I-suffix devices are characterized for operation from – 40°C to 85°C. The M-suffix devices are characterized for operation over the full military temperature range of – 55°C to 125°C. AVAILABLE OPTIONS PACKAGE TA 0°C to 70°C VIOmax AT 25°C SMALL OUTLINE (D)† CHIP CARRIER (FK) CERAMIC DIP (J) CERAMIC DIP (JG) PLASTIC DIP (N) PLASTIC DIP (P) TSSOP PACKAGE (PW) FLAT PACKAGE (W) 10 mV 6 mV 3 mV TL071CD TL071ACD TL071BCD — — — — TL071CP TL071ACP TL071BCP TL071CPWLE — — — 10 mV 6 mV 3 mV TL072CD TL072ACD TL072BCD — — — — TL072CP TL072ACP TL072BCP TL072CPWLE — — — 10 mV 6 mV 3 mV TL074CD TL074ACD TL074BCD — — — TL074CN TL074ACN TL074BCN — TL074CPWLE — — — TL071ID TL072ID TL074ID — — — — — TL074IN TL071IP TL072IP — — — TL071MFK TL072MFK TL074MFK — — TL074MJ TL071MJG TL072MJG — — — TL074MN — TL072MP — — — — TL074MW – 40°C to 85°C 6 mV – 55°C to 125 C 125°C 6 mV 6 mV 9 mV — † The D package is available taped and reeled. Add the suffix R to the device type (e.g., TL071CDR). The PW package is only available left-ended taped and reeled (e.g., TL072CPWLE). Please be aware that an important notice concerning availability, standard warranty, and use in critical applications of Texas Instruments semiconductor products and disclaimers thereto appears at the end of this data sheet. Copyright 1996, Texas Instruments Incorporated PRODUCTION DATA information is current as of publication date. Products conform to specifications per the terms of Texas Instruments standard warranty. Production processing does not necessarily include testing of all parameters. POST OFFICE BOX 655303 • DALLAS, TEXAS 75265 1 TL071, TL071A, TL071B, TL072 TL072A, TL072B, TL074, TL074A, TL074B LOW-NOISE JFET-INPUT OPERATIONAL AMPLIFIERS SLOS080D – SEPTEMBER 1978 – REVISED AUGUST 1996 TL072, TL072A, TL072B D, JG, P, OR PW PACKAGE (TOP VIEW) TL071, TL071A, TL071B D, JG, P, OR PW PACKAGE (TOP VIEW) 8 2 7 NC VCC + 3 6 OUT 4 5 OFFSET N2 1OUT 1IN – 1IN + VCC – 3 2 1 20 19 18 5 17 6 16 7 15 8 14 9 10 11 12 13 2 7 3 6 4 5 VCC + 2OUT 2IN – 2IN + 1OUT 1IN – 1IN + VCC + 2IN + 2IN – 2OUT NC 1OUT NC VCC + NC NC VCC + NC OUT NC NC 1IN – NC 1IN + NC 4 3 2 1 20 19 18 5 17 6 16 7 15 8 14 9 10 11 12 13 1 14 2 13 3 12 4 11 5 10 6 9 7 8 NC 2OUT NC 2IN – NC 1IN+ NC VCC+ NC 2IN+ 4 3 2 1 20 19 18 5 17 6 16 7 15 8 14 9 10 11 12 13 NC – No internal connection symbols TL071 TL072 (each amplifier) TL074 (each amplifier) OFFSET N1 IN + + IN + + IN – – OUT IN – – OUT OFFSET N2 2 POST OFFICE BOX 655303 4OUT 4IN – 4IN + VCC – 3IN + 3IN – 3OUT TL074 FK PACKAGE (TOP VIEW) NC VCC – NC 2IN+ NC 4 NC VCC – NC OFFSET N2 NC NC IN – NC IN + NC 8 TL072 FK PACKAGE (TOP VIEW) NC OFFSET N1 NC NC NC TL071 FK PACKAGE (TOP VIEW) 1 1IN – 1OUT NC 4OUT 4IN – 1 2IN– 2OUT NC 3OUT 3IN– OFFSET N1 IN – IN + VCC – TL074, TL074A, TL074B D, J, N, OR PW PACKAGE TL074 . . . W PACKAGE (TOP VIEW) • DALLAS, TEXAS 75265 4IN+ NC VCC – NC 3IN+ TL071, TL071A, TL071B, TL072 TL072A, TL072B, TL074, TL074A, TL074B LOW-NOISE JFET-INPUT OPERATIONAL AMPLIFIERS SLOS080D – SEPTEMBER 1978 – REVISED AUGUST 1996 schematic (each amplifier) VCC + IN + 64 Ω IN – 128 Ω OUT 64 Ω C1 18 pF ÎÎÎ ÁÁÁ ÁÁÁ ÁÁÁ 1080 Ω ÁÁÁÁÁ ÁÁÁÁÁ ÁÁÁÁÁ 1080 Ω VCC – OFFSET NULL (N1) OFFSET NULL (N2) TL071 Only All component values shown are nominal. COMPONENT COUNT† COMPONENT TYPE Resistors Transistors JFET Diodes Capacitors epi-FET TL071 TL072 TL074 11 14 2 1 1 1 22 28 4 2 2 2 44 56 6 4 4 4 † Includes bias and trim circuitry POST OFFICE BOX 655303 • DALLAS, TEXAS 75265 3 TL071, TL071A, TL071B, TL072 TL072A, TL072B, TL074, TL074A, TL074B LOW-NOISE JFET-INPUT OPERATIONAL AMPLIFIERS SLOS080D – SEPTEMBER 1978 – REVISED AUGUST 1996 absolute maximum ratings over operating free-air temperature range (unless otherwise noted)† Supply voltage, VCC + (see Note 1) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18 V Supply voltage, VCC – (see Note 1) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . – 18 V Differential input voltage, VID (see Note 2) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ± 30 V Input voltage, VI (see Notes 1 and 3) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ±15 V Duration of output short circuit (see Note 4) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . unlimited Continuous total power dissipation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . See Dissipation Rating Table Operating free-air temperature range, TA: C suffix . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0°C to 70°C I suffix . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . – 40°C to 85°C M suffix . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . – 55°C to 125°C Storage temperature range . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . – 65°C to 150°C Case temperature for 60 seconds: FK package . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 260°C Lead temperature 1,6 mm (1/16 inch) from case for 10 seconds: J, JG, or W package . . . . . . . . . . . . 300°C Lead temperature 1,6 mm (1/16 inch) from case for 10 seconds: D, N, P, or PW package . . . . . . . . . 260°C † Stresses beyond those listed under “absolute maximum ratings” may cause permanent damage to the device. These are stress ratings only, and functional operation of the device at these or any other conditions beyond those indicated under “recommended operating conditions” is not implied. Exposure to absolute-maximum-rated conditions for extended periods may affect device reliability. NOTES: 1. All voltage values, except differential voltages, are with respect to the midpoint between VCC+ and VCC – . 2. Differential voltages are at IN+ with respect to IN –. 3. The magnitude of the input voltage must never exceed the magnitude of the supply voltage or 15 V, whichever is less. 4. The output may be shorted to ground or to either supply. Temperature and /or supply voltages must be limited to ensure that the dissipation rating is not exceeded. DISSIPATION RATING TABLE 4 PACKAGE TA ≤ 25°C POWER RATING DERATING FACTOR DERATE ABOVE TA TA = 70°C POWER RATING TA = 85°C POWER RATING TA = 125°C POWER RATING D (8 pin) 680 mW 5.8 mW/°C 33°C 465 mW 378 mW N/A D (14 pin) 680 mW 7.6 mW/°C 60°C 604 mW 490 mW N/A FK 680 mW 11.0 mW/°C 88°C 680 mW 680 mW 273 mW J 680 mW 11.0 mW/°C 88°C 680 mW 680 mW 273 mW JG 680 mW 8.4 mW/°C 69°C 672 mW 546 mW 210 mW N 680 mW 9.2 mW/°C 76°C 680 mW 597 mW N/A P 680 mW 8.0 mW/°C 65°C 640 mW 520 mW N/A PW (8 pin) 525 mW 4.2 mW/°C 70°C 525 mW N/A N/A PW (14 pin) 700 mW 5.6 mW/°C 70°C 700 mW N/A N/A W 680 mW 8.0 mW/°C 65°C 640 mW 520 mW 200 mW POST OFFICE BOX 655303 • DALLAS, TEXAS 75265 electrical characteristics, VCC± = ±15 V (unless otherwise noted) PARAMETER TEST CONDITIONS† TL071C TL072C TL074C TA‡ MIN VIO Input offset voltage VO = 0 0, RS = 50 Ω αVIO Temperature coefficient of input offset voltage VO = 0, RS = 50 Ω IIO Input offset current VO = 0 25°C TL071AC TL072AC TL074AC TYP MAX 3 10 Full range MIN TYP MAX 3 6 13 Full range 18 25°C 5 100 65 200 Full range MIN TL071I TL072I TL074I TYP MAX 2 3 7.5 MIN 100 65 200 MAX 3 6 8 18 5 100 65 200 mV µV/°C 18 5 2 UNIT TYP 5 18 10 25°C TL071BC TL072BC TL074BC 5 100 pA 2 nA 65 200 pA 20 nA 2 Input bias current§ VICR Common-mode Common mode input voltage range VOM Maximum peak eak output voltage swing RL ≥ 10 kΩ AVD Large-signal differential voltage amplification VO = ±10 V V, B1 Unity-gain bandwidth 25°C 3 3 3 3 ri Input resistance 25°C 1012 1012 1012 1012 Ω CMRR Common-mode rejection ratio VIC = VICRmin, RS = 50 Ω VO = 0, 25°C 70 100 75 100 75 100 75 100 dB kSVR Supply-voltage rejection ratio (∆VCC ± /∆VIO) VCC = ± 9 V to ± 15 V, VO = 0, RS = 50 Ω 25°C 70 100 80 100 80 100 80 100 dB ICC Supply y current (each amplifier) VO = 0 0, 25°C 14 1.4 VO1/ VO2 Crosstalk attenuation AVD = 100 25°C 120 VO = 0 Full range RL = 10 kΩ RL ≥ 2 kΩ 7 ±11 –12 12 to 15 ±11 –12 12 to 15 ±11 –12 12 to 15 ±11 –12 12 to 15 25°C ±12 ±13.5 ±12 ±13.5 ±12 ±13.5 ±12 ±13.5 ±12 ±12 ±12 ±12 ±10 ±10 ±10 ±10 25°C 25 Full range 15 200 50 200 50 200 50 V V 200 V/mV 25 25 2.5 25 14 1.4 120 25 2.5 25 14 1.4 120 25 2.5 14 1.4 120 MHz 25 2.5 mA dB † All characteristics are measured under open-loop conditions with zero common-mode voltage unless otherwise specified. ‡ Full range is TA = 0°C to 70°C for TL07_C,TL07_AC, TL07_BC and is TA = – 40°C to 85°C for TL07_I. § Input bias currents of a FET-input operational amplifier are normal junction reverse currents, which are temperature sensitive as shown in Figure 4. Pulse techniques must be used that maintain the junction temperature as close to the ambient temperature as possible. 5 SLOS080D – SEPTEMBER 1978 – REVISED AUGUST 1996 No load 7 25°C Full range RL ≥ 2 kΩ 7 TL071, TL071A, TL071B, TL072 TL072A, TL072B, TL074, TL074A, TL074B LOW-NOISE JFET-INPUT OPERATIONAL AMPLIFIERS POST OFFICE BOX 655303 • DALLAS, TEXAS 75265 IIB TL071, TL071A, TL071B, TL072 TL072A, TL072B, TL074, TL074A, TL074B LOW-NOISE JFET-INPUT OPERATIONAL AMPLIFIERS SLOS080D – SEPTEMBER 1978 – REVISED AUGUST 1996 electrical characteristics, VCC ± = ± 15 V (unless otherwise noted) PARAMETER TEST CONDITIONS† TL071M TL072M TA‡ MIN VIO Input offset voltage VO = 0 0, RS = 50 Ω αVIO Temperature coefficient of input offset voltage VO = 0, RS = 50 Ω IIO Input offset current VO = 0 IIB Input bias current‡ VICR Common-mode input voltage range VOM Maximum M i peak k output t t voltage swing 25°C TYP MAX 3 6 Full range MIN TYP 3 9 Full range 18 25°C 5 100 65 200 Full range RL ≥ 10 kΩ pA 20 nA 65 200 pA 50 nA –12 to 15 ±11 –12 to 15 25°C ±12 ±13.5 ±12 ±13.5 25°C ±12 ±10 ±10 35 µV/°C 100 ±11 ±12 200 35 mV 5 25°C Full range RL ≥ 2 kΩ 9 18 50 RL = 10 kΩ UNIT MAX 15 20 25°C VO = 0 TL074M V V 200 AVD Large-signal g g differential voltage amplification VO = ±10 V V, B1 Unity-gain bandwidth TA = 25°C 3 3 1012 1012 Ω RL ≥ 2 kΩ 15 V/mV 15 MHz ri Input resistance TA = 25°C CMRR Common-mode rejection ratio VIC = VICRmin, VO = 0, RS = 50 Ω 25°C 80 86 80 86 dB kSVR Supply-voltage rejection ratio (∆VCC ± /∆VIO) VCC = ± 9 V to ± 15 V, RS = 50 Ω VO = 0, 25°C 80 86 80 86 dB ICC Supply current (each amplifier) VO = 0, 25°C No load 1.4 2.5 1.4 2.5 mA VO1/ VO2 Crosstalk attenuation AVD = 100 25°C 120 120 dB † Input bias currents of a FET-input operational amplifier are normal junction reverse currents, which are temperature sensitive as shown in Figure 4. Pulse techniques must be used that will maintain the junction temperature as close to the ambient temperature as possible. ‡ All characteristics are measured under open-loop conditions with zero common-mode voltage unless otherwise specified. Full range is TA = – 55°C to 125°C. 6 POST OFFICE BOX 655303 • DALLAS, TEXAS 75265 TL071, TL071A, TL071B, TL072 TL072A, TL072B, TL074, TL074A, TL074B LOW-NOISE JFET-INPUT OPERATIONAL AMPLIFIERS SLOS080D – SEPTEMBER 1978 – REVISED AUGUST 1996 operating characteristics, VCC ± = ± 15 V, TA = 25°C PARAMETER TL07xM TEST CONDITIONS SR Slew rate at unity gain VI = 10 V, CL = 100 pF, RL = 2 kΩ, See Figure 1 tr Rise time overshoot factor VI = 20 mV,, CL = 100 pF, RL = 2 kΩ,, See Figure 1 Vn Equivalent q input noise voltage RS = 20 Ω In Equivalent input noise current RS = 20 Ω, f = 1 kHz THD Total harmonic distortion VIrms = 6 V, RL ≥ 2 kΩ, f = 1 kHz AVD = 1, RS ≤ 1 kΩ , MIN TYP 5 13 ALL OTHERS MAX MAX UNIT MIN TYP 8 13 V/µs µs 0.1 0.1 20% 20% 18 18 nV/√Hz 4 4 µV 0.01 0.01 0.003% 0.003% f = 1 kHz f = 10 Hz to 10 kHz pA/√Hz PARAMETER MEASUREMENT INFORMATION 10 kΩ – VI + CL = 100 pF 1 kΩ VO RL = 2 kΩ + RL IN – CL = 100 pF Figure 2. Gain-of-10 Inverting Amplifier Figure 1. Unity-Gain Amplifier – TL071 OUT IN + N2 + VI – VO N1 100 kΩ 1.5 kΩ VCC – Figure 3. Input Offset Voltage Null Circuit POST OFFICE BOX 655303 • DALLAS, TEXAS 75265 7 TL071, TL071A, TL071B, TL072 TL072A, TL072B, TL074, TL074A, TL074B LOW-NOISE JFET-INPUT OPERATIONAL AMPLIFIERS SLOS080D – SEPTEMBER 1978 – REVISED AUGUST 1996 TYPICAL CHARACTERISTICS Table of Graphs FIGURE IIB Input bias current vs Free-air temperature 4 VOM Maximum output voltage vs Frequency vs Free-air temperature vs Load resistance vs Supply voltage 5, 6, 7 8 9 10 AVD Large signal differential voltage amplification Large-signal vs Free-air temperature vs Frequency 11 12 Phase shift vs Frequency 12 Normalized unity-gain bandwidth vs Free-air temperature 13 Normalized phase shift vs Free-air temperature 13 CMRR Common-mode rejection ratio vs Free-air temperature 14 ICC Supply current vs Supplyy voltage g vs Free-air temperature 15 16 PD Total power dissipation vs Free-air temperature 17 Normalized slew rate vs Free-air temperature 18 Vn Equivalent input noise voltage vs Frequency 19 THD Total harmonic distortion vs Frequency 20 Large-signal pulse response vs Time 21 Output voltage vs Elapsed time 22 VO 8 POST OFFICE BOX 655303 • DALLAS, TEXAS 75265 TL071, TL071A, TL071B, TL072 TL072A, TL072B, TL074, TL074A, TL074B LOW-NOISE JFET-INPUT OPERATIONAL AMPLIFIERS SLOS080D – SEPTEMBER 1978 – REVISED AUGUST 1996 TYPICAL CHARACTERISTICS† MAXIMUM PEAK OUTPUT VOLTAGE vs FREQUENCY INPUT BIAS CURRENT vs FREE-AIR TEMPERATURE 100 ± 15 VOM VOM – Maximum Peak Output Voltage – V IIIB– IB Input Bias Current – nA VCC± = ± 15 V 10 1 0.1 0.01 – 75 – 25 0 25 50 75 100 ÎÎÎÎÎ ÎÎÎÎÎ ± 10 VCC ± = ± 10 V ± 7.5 VCC ± = ± 5 V ±5 ± 2.5 125 0 100 1k TA – Free-Air Temperature – °C MAXIMUM PEAK OUTPUT VOLTAGE vs FREQUENCY VCC ± = ± 15 V ± 10 ± 15 RL = 2 kΩ TA = 25°C See Figure 2 VCC ± = ± 10 V ± 7.5 ÁÁ ÁÁ ÁÁ ±5 VCC ± = ± 5 V ± 2.5 0 100 1k 10 k 100 k f – Frequency – Hz 1M 10 M MAXIMUM PEAK OUTPUT VOLTAGE vs FREQUENCY 1M 10 M VOM VOM – Maximum Peak Output Voltage – V VOM VOM – Maximum Peak Output Voltage – V ÎÎÎÎÎ ÎÎÎÎÎ ± 12.5 10 k 100 k f – Frequency – Hz Figure 5 Figure 4 ± 15 RL = 10 kΩ TA = 25°C See Figure 2 ± 12.5 ÁÁÁ ÁÁÁ – 50 VCC ± = ± 15 V ± 12.5 ± 10 ÎÎÎÎ ÎÎÎÎ ÎÎÎÎ ÎÎÎÎ VCC ± = ± 15 V RL = 2 kΩ See Figure 2 TA = 25°C TA = – 55°C ± 7.5 ±5 ÁÁÁ ÁÁÁ ÁÁÁ TA = 125°C ± 2.5 0 10 k Figure 6 40 k 100 k 400 k 1 M f – Frequency – Hz 4M 10 M Figure 7 † Data at high and low temperatures are applicable only within the rated operating free-air temperature ranges of the various devices. POST OFFICE BOX 655303 • DALLAS, TEXAS 75265 9 TL071, TL071A, TL071B, TL072 TL072A, TL072B, TL074, TL074A, TL074B LOW-NOISE JFET-INPUT OPERATIONAL AMPLIFIERS SLOS080D – SEPTEMBER 1978 – REVISED AUGUST 1996 TYPICAL CHARACTERISTICS† MAXIMUM PEAK OUTPUT VOLTAGE vs LOAD RESISTANCE MAXIMUM PEAK OUTPUT VOLTAGE vs FREE-AIR TEMPERATURE ± 15 RL = 10 kΩ ÎÎÎÎ ÎÎÎÎ ± 12.5 VOM VOM – Maximum Peak Output Voltage – V VOM – Maximum Peak Output Voltage – V VOM ± 15 RL = 2 kΩ ± 10 ± 7.5 ±5 ÁÁ ÁÁ ± 2.5 VCC ± = ± 15 V See Figure 2 0 – 75 – 50 – 25 0 25 50 75 100 125 VCC ± = ± 15 V TA = 25°C See Figure 2 ± 12.5 ± 10 ± 7.5 ±5 ÁÁ ÁÁ ± 2.5 0 0.1 0.2 TA – Free-Air Temperature – °C 0.4 4 7 10 Figure 9 LARGE-SIGNAL DIFFERENTIAL VOLTAGE AMPLIFICATION vs FREE-AIR TEMPERATURE MAXIMUM PEAK OUTPUT VOLTAGE vs SUPPLY VOLTAGE ± 15 VOM VOM – Maximum Peak Output Voltage – V 2 RL – Load Resistance – kΩ Figure 8 1000 RL = 10 kΩ TA = 25°C 400 AVD A VD – Large-Signal Differential Voltage Amplification – V/mV ± 12.5 ± 10 ± 7.5 ÁÁ ÁÁ ÁÁ 0.7 1 ±5 ± 2.5 200 100 40 20 10 4 2 0 0 2 4 6 8 10 12 14 16 1 – 75 VCC ± = ± 15 V VO = ± 10 V RL = 2 kΩ – 50 – 25 0 25 50 75 100 TA – Free-Air Temperature – °C |VCC ±| – Supply Voltage – V Figure 11 Figure 10 † Data at high and low temperatures are applicable only within the rated operating free-air temperature ranges of the various devices. 10 POST OFFICE BOX 655303 • DALLAS, TEXAS 75265 125 TL071, TL071A, TL071B, TL072 TL072A, TL072B, TL074, TL074A, TL074B LOW-NOISE JFET-INPUT OPERATIONAL AMPLIFIERS SLOS080D – SEPTEMBER 1978 – REVISED AUGUST 1996 TYPICAL CHARACTERISTICS† LARGE-SIGNAL DIFFERENTIAL VOLTAGE AMPLIFICATION AND PHASE SHIFT vs FREQUENCY VCC± = ± 5 V to ± 15 V RL = 2 kΩ TA = 25°C 105 0° 104 Differential Voltage Amplification 103 45° Phase Shift AVD A VD – Large-Signal Differential Voltage Amplification 106 90° 102 Phase Shift 101 135° 1 1 10 100 1k 10 k 100 k f – Frequency – Hz 1M 180° 10 M Figure 12 NORMALIZED UNITY-GAIN BANDWIDTH AND PHASE SHIFT vs FREE-AIR TEMPERATURE 1.03 Unity-Gain Bandwidth 1.2 1.1 1 1.01 Phase Shift 1 0.9 0.8 0.7 – 75 1.02 0.99 VCC ± = ± 15 V RL = 2 kΩ f = B1 for Phase Shift – 50 – 25 0 25 50 75 100 TA – Free-Air Temperature – °C Normalized Phase Shift Normalized Unity-Gain Bandwidth 1.3 0.98 0.97 125 Figure 13 † Data at high and low temperatures are applicable only within the rated operating free-air temperature ranges of the various devices. POST OFFICE BOX 655303 • DALLAS, TEXAS 75265 11 TL071, TL071A, TL071B, TL072 TL072A, TL072B, TL074, TL074A, TL074B LOW-NOISE JFET-INPUT OPERATIONAL AMPLIFIERS SLOS080D – SEPTEMBER 1978 – REVISED AUGUST 1996 TYPICAL CHARACTERISTICS† SUPPLY CURRENT PER AMPLIFIER vs SUPPLY VOLTAGE COMMON-MODE REJECTION RATIO vs FREE-AIR TEMPERATURE 2 VCC ± = ± 15 V RL = 10 kΩ ICC± – Supply Current Per Amplifier – mA I CC CMRR – Common-Mode Rejection Ratio – dB 89 88 87 86 85 83 – 75 1.6 1.4 1.2 1 0.8 ÁÁ ÁÁ 84 – 50 – 25 0 25 50 75 100 TA = 25°C No Signal No Load 1.8 0.6 0.4 0.2 0 125 0 2 TA – Free-Air Temperature – °C 4 12 14 VCC ± = ± 15 V No Signal No Load 1.8 1.6 1.4 1.2 1 0.8 0.6 0.4 0.2 250 VCC ± = ± 15 V No Signal No Load 225 200 175 TL074 150 125 ÎÎÎ ÎÎÎ 100 TL072 75 TL071 50 25 – 50 – 25 0 25 50 75 100 125 0 – 75 – 50 TA – Free-Air Temperature – °C – 25 0 25 50 75 100 TA – Free-Air Temperature – °C Figure 16 Figure 17 † Data at high and low temperatures are applicable only within the rated operating free-air temperature ranges of the various devices. 12 16 TOTAL POWER DISSIPATION vs FREE-AIR TEMPERATURE PD PD – Total Power Dissipation – mW 2 ICC± – Supply Current Per Amplifier – mA I CC 10 Figure 15 SUPPLY CURRENT PER AMPLIFIER vs FREE-AIR TEMPERATURE 0 – 75 8 |VCC ±| – Supply Voltage – V Figure 14 ÁÁÁ ÁÁÁ ÁÁÁ 6 POST OFFICE BOX 655303 • DALLAS, TEXAS 75265 125 TL071, TL071A, TL071B, TL072 TL072A, TL072B, TL074, TL074A, TL074B LOW-NOISE JFET-INPUT OPERATIONAL AMPLIFIERS SLOS080D – SEPTEMBER 1978 – REVISED AUGUST 1996 TYPICAL CHARACTERISTICS NORMALIZED SLEW RATE vs FREE-AIR TEMPERATURE ÁÁÁ ÁÁÁ ÁÁÁ ÁÁÁ Vn V nV/ Hz n – Equivalent Input Noise Voltage – nV/Hz Normalized Slew Rate – V/µ s 1.15 VCC ± = ± 15 V RL = 2 kΩ CL = 100 pF 1.10 1.05 1 0.95 0.90 0.85 – 75 EQUIVALENT INPUT NOISE VOLTAGE vs FREQUENCY 50 VCC ± = ± 15 V AVD = 10 RS = 20 Ω TA = 25°C 40 30 20 10 0 – 50 – 25 0 25 50 75 100 10 125 40 100 TA – Free-Air Temperature – °C Figure 18 6 VCC ± = ± 15 V AVD = 1 VI(RMS) = 6 V TA = 25°C 0.1 0.04 0.01 0.004 0.001 100 400 1k 4 k 10 k f – Frequency – Hz VOLTAGE-FOLLOWER LARGE-SIGNAL PULSE RESPONSE VI and VO – Input and Output Voltages – V THD – Total Harmonic Distortion – % 0.4 40 k 100 k Figure 19 TOTAL HARMONIC DISTORTION vs FREQUENCY 1 400 1 k 4 k 10 k f – Frequency – Hz 40 k 100 k VCC ± = ± 15 V RL = 2 kΩ CL = 100 pF TA = 25°C 4 Output 2 0 ÁÁ ÁÁ ÁÁ ÁÁ ÎÎÎ ÎÎÎ –2 Input –4 –6 0 0.5 1 1.5 t – Time – µs 2 2.5 3 3.5 Figure 21 Figure 20 POST OFFICE BOX 655303 • DALLAS, TEXAS 75265 13 TL071, TL071A, TL071B, TL072 TL072A, TL072B, TL074, TL074A, TL074B LOW-NOISE JFET-INPUT OPERATIONAL AMPLIFIERS SLOS080D – SEPTEMBER 1978 – REVISED AUGUST 1996 TYPICAL CHARACTERISTICS OUTPUT VOLTAGE vs ELAPSED TIME 28 24 VO V O – Output Voltage – mV Overshoot 20 90% 16 12 ÁÁÁ ÁÁÁ 8 4 VCC ± = ± 15 V RL = 2 kΩ TA = 25°C 10% 0 tr –4 0 0.1 0.2 0.3 0.4 0.5 t – Elapsed Time – µs 0.6 Figure 22 14 POST OFFICE BOX 655303 • DALLAS, TEXAS 75265 0.7