bq24740 www.ti.com SLUS736 – DECEMBER 2006 Host-controlled Multi-chemistry Battery Charger with Low Input Power Detect FEATURES APPLICATIONS • • • • • • • • • • LODRV PGND REGN HIDRV PH DPMDET ACN 2 20 CELLS ACP 3 bq24740 19 SRP LPMD 4 28 LD QFN 18 SRN ACDET 5 TOP VIEW 17 BAT ACSET 6 16 SRSET LPREF 7 15 IADAPT 9 10 11 12 13 14 EXTPWR 8 ISYNSET • 21 VADJ • CHGEN VREF • 28 27 26 25 24 23 22 1 VDAC • • • The bq24740 charges two, three, or four series Li+ cells, supporting up to 10 A of charge current, and is available in a 28-pin, 5x5-mm thin QFN package. BTST • The bq24740 is a high-efficiency, synchronous battery charger with integrated compensation and system power selector logic, offering low component count for space-constrained multi-chemistry battery charging applications. Ratiometric charge current and voltage programming allows very high regulation accuracies, and can be either hardwired with resistors or programmed by the system power-management microcontroller using a DAC or GPIOs. AGND • DESCRIPTION PVCC • Notebook and Ultra-Mobile Computers Portable Data-Capture Terminals Portable Printers Medical Diagnostics Equipment Battery Bay Chargers Battery Back-up Systems IADSLP • NMOS-NMOS Synchronous Buck Converter with 300 kHz Frequency and >95% Efficiency 30-ns Minimum Driver Dead-time and 99.5% Maximum Effective Duty Cycle High-Accuracy Voltage and Current Regulation – ±0.5% Charge Voltage Accuracy – ±3% Charge Current Accuracy – ±3% Adapter Current Accuracy – ±2% Input Current Sense Amp Accuracy Integration – Internal Loop Compensation – Internal Soft Start Safety – Input Overvoltage Protection (OVP) – Dynamic Power Management (DPM) with Status Indicator – Reverse-Conduction Protection Input FET Supports Two, Three, or Four Li+ Cells 5 – 24 V AC/DC-Adapter Operating Range Analog Inputs with Ratiometric Programming via Resistors or DAC/GPIO Host Control – Charge Voltage (4-4.512 V/cell) – Charge Current (up to 10 A, with 10-mΩ sense resistor) – Adapter Current Limit (DPM) Status and Monitoring Outputs – AC/DC Adapter Present with Programmable Voltage Threshold – Low Input-Power Detect with Adjustable Threshold and Hysteresis – DPM Loop Active – Current Drawn from Input Source Battery Discharge Current Sense with No Adapter, or Selectable Low-Iq mode Supports Any Battery Chemistry: Li+, NiCd, NiMH, Lead Acid, etc. Charge Enable 10-µA Off-State Current 28-pin, 5x5-mm QFN package Please be aware that an important notice concerning availability, standard warranty, and use in critical applications of Texas Instruments semiconductor products and disclaimers thereto appears at the end of this data sheet. PRODUCTION DATA information is current as of publication date. Products conform to specifications per the terms of the Texas Instruments standard warranty. Production processing does not necessarily include testing of all parameters. Copyright © 2006, Texas Instruments Incorporated bq24740 www.ti.com SLUS736 – DECEMBER 2006 These devices have limited built-in ESD protection. The leads should be shorted together or the device placed in conductive foam during storage or handling to prevent electrostatic damage to the MOS gates. DESCRIPTION (CONTINUED) The bq24740 features Dynamic Power Management (DPM) and input power limiting. These features reduce battery charge current when the input power limit is reached to avoid overloading the AC adapter when supplying the load and the battery charger simultaneously. A highly-accurate current-sense amplifier enables precise measurement of input current from the AC adapter to monitor the overall system power. If the adapter current is above the programmed low-power threshold, a signal is sent to host so that the system optimizes its power performance according to what is available from the adapter. TYPICAL APPLICATION C16 10 mF C17 10 mF C18 10 mF SYSTEM ADAPTER+ ADAPTER- C1 10 mF RAC P P Q1 (ACFET) Q2 (ACFET) SI4435 SI4435 Controlled by C2 HOST R1 0.1 mF 432 kW 1% C6 C7 10 mF 10 mF 0.010 W C3 0.1 mF ACN PVCC C8 1 mF ACP ACDET bq24740 R3 10 kW PH BTST EXTPWR EXTPWR D1 BAT54 C9 L1 0.1 mF 8.2 mH C10 1 mF DAC ACSET LODRV VREF R5 10 kW N R4 10 kW C4 1 mF BAT VREF CELLS R7 200 kW CHGEN LPREF VDAC ISYNSET VADJ IADAPT C5 C14 0.1 mF SRN LPMD ADC C13 0.1 mF Q5 FDS6680A SRP DPMDET DAC PACK+ C12 10 mF PGND IADSLP HOST R SR 0.010 W C11 10 mF REGN SRSET P Q4 FDS6680A HIDRV AGND VREF N R2 66.5 kW 1% PowerPad R6 33 kW C15 0.1 mF R8 24.9 kW 100 pF R9 1.8 MW (1) Pull-up rail could be either VREF or other system rail . (2) SRSET/ACSET could come from either DAC or resistor dividers . VIN = 20 V, VBAT = 3-cell Li-Ion, ICHARGE = 3 A, IADAPTER_LIMIT = 4 A Figure 1. Typical System Schematic, Voltage and Current Programmed by DAC 2 Submit Documentation Feedback Q3(BATFET) SI4435 Controlled by HOST PACK- bq24740 www.ti.com SLUS736 – DECEMBER 2006 C16 10 mF C17 10 mF C18 10 mF SYSTEM ADAPTER+ ADAPTER- RAC C1 10 mF P P Q1 (ACFET) Q2 (ACFET) SI4435 SI4435 Controlled by C2 HOST R1 0.1 mF 432 kW 1% C6 C7 10 mF 10 mF 0.010 W C3 0.1 mF ACN PVCC C8 1 mF ACP ACDET bq24740 R3 10 kW PH BTST EXTPWR EXTPWR D1 R9 42 kW R11 66.5 kW SRSET ACSET R4 10 kW R5 10 kW GPIO 8.2 mH R SR 0.010 W PACK+ C12 10 mF C11 10 mF LODRV C13 0.1 mF Q5 FDS6680A PACK- C14 0.1 mF PGND C4 1 mF IADSLP SRP DPMDET SRN LPMD BAT CHGEN VREF R7 200 kW LPREF ISYNSET VDAC R6 33 kW VADJ IADAPT C5 0.1 mF C10 1 mF CELLS ADC L1 N VREF HOST C9 REGN R10 100 kW R12 100 kW BAT54 P Q4 FDS6680A HIDRV AGND VREF N R2 66.5 kW 1% Q3(BATFET) SI4435 Controlled by HOST C15 0.1 mF R8 24.9 kW PowerPad 100 pF R9 1.8 MW (1) Pull-up rail could be either VREF or other system rail . (2) SRSET/ACSET could come from either DAC or resistor dividers. A. VIN = 20 V, VBAT = 3-cell Li-Ion, ICHARGE = 3 A, IADAPTER_LIMIT = 4 A Figure 2. Typical System Schematic, Voltage and Current Programmed by Resistor Submit Documentation Feedback 3 bq24740 www.ti.com SLUS736 – DECEMBER 2006 C17 10 mF C18 10 mF C19 10 mF ADAPTER + ADAPTER - SYSTEM C1 10 mF R1 P RAC 0.010 W P Q1 (ACFET) Q2 (ACFET) SI4435 SI4435 Controlled by HOST C2 0.1 mF 432 kW 1% C6 10 mF C7 10 mF C3 ACN 0.1 mF PVCC C8 ACP 1 mF Q3(BATFET) SI4435 Controlled by HOST ACDET VREF R3 bq24740 10 kW PH BTST EXTPWR /EXTPWR N R2 D1 BAT54 C10 1 mF L1 C9 0.1 mF DAC PACK+ C13 0.1 mF Q5 FDS6680A LODRV 10 kW R5 10 kW 1 mF PGND IADSLP HOST BAT VREF CELLS CHGEN ISYNSET R6 33 kW VADJ IADAPT C15 0.1 mF R7 200 kW LPREF VDAC C5 0.1 mF SRN LPMD ADC C14 SRP DPMDET DAC PACK- N R4 C4 C12 10 mF C11 10 mF ACSET VREF RSR 0.010 W 8.2 mH REGN SRSET P Q4 FDS6680A HIDRV AGND 66.5 kW 1% R8 24.9 kW PowerPad 100 pF R9 (1) Pull-up rail could be either VREF or other system rail 1.8 MW . (2) SRSET/ACSET could come from either DAC or resistor dividers . VIN = 20 V, VBAT = 3-cell Li-Ion, ICHARGE = 3 A, IADAPTER_LIMIT = 4 A Figure 3. Typical System Schematic: Sensing Battery Discharge Current, When Adapter Removed. (Set IADSLP at logic high) ORDERING INFORMATION Part number Package bq24740 28-PIN 5 x 5 mm QFN Ordering Number (Tape and Reel) Quantity bq24740RHDR 3000 bq24740RHDT 250 PACKAGE THERMAL DATA (1) (2) 4 PACKAGE θJA TA = 70°C POWER RATING DERATING FACTOR ABOVE TA = 25°C QFN – RHD (1) (2) 39°C/W 2.36 W 0.028 W/°C For the most current package and ordering information, see the Package Option Addendum at the end of this document, or see the TI Web site at www.ti.com. This data is based on using the JEDEC High-K board and the exposed die pad is connected to a Cu pad on the board. This is connected to the ground plane by a 2x3 via matrix. Submit Documentation Feedback bq24740 www.ti.com SLUS736 – DECEMBER 2006 Table 1. TERMINAL FUNCTIONS – 28-PIN QFN TERMINAL NAME NO. DESCRIPTION CHGEN 1 Charge enable active-low logic input. LO enables charge. HI disables charge. ACN 2 Adapter current sense resistor, negative input. An optional 0.1-µF ceramic capacitor is placed from ACN pin to AGND for common-mode filtering. An optional 0.1-µF ceramic capacitor is placed from ACN to ACP to provide differential-mode filtering. ACP 3 Adapter current sense resistor, positive input. (See comments with ACN description) 4 Low power mode detect active-high open-drain logic output. Place a 10-kΩ pullup resistor from LPMD pin to the pullup-voltage rail. Place a positive-feedback resistor from LPMD pin to LPREF pin for programming hysteresis (see design example for calculation). The output is HI when IADAPT pin voltage is lower than LPREF pin voltage. The output is LO when IADAPT pin voltage is higher than LPREF pin voltage. 5 Adapter detected voltage set input. Program the adapter detect threshold by connecting a resistor divider from adapter input to ACDET pin to AGND pin. Adapter voltage is detected if ACDET-pin voltage is greater than 2.4 V. The IADAPT current sense amplifier is active when the ACDET pin voltage is greater than 0.6 V. Input overvoltage, ACOV, disables charge and ACDRV when ACDET > 3.1 V. ACOV does not latch 6 Adapter current set input. The voltage ratio of ACSET voltage versus VDAC voltage programs the input current regulation set-point during Dynamic Power Management (DPM). Program by connecting a resistor divider from VDAC to ACSET to AGND; or by connecting the output of an external DAC to the ACSET pin and connect the DAC supply to the VDAC pin. 7 Low power voltage set input. Connect a resistor divider from VREF to LPREF and AGND to program the reference for the LOPWR comparator. The LPREF-pin voltage is compared to the IADAPT-pin voltage and the logic output is given on the LPMD open-drain pin. Connecting a positive-feedback resistor from LPREF pin to LPMD pin programs the hysteresis. IADSLP 8 Enable IADAPT to enter sleep mode; active-low logic input. Allows low Iq sleep mode when adapter not detected. Logic low turns off the Input Current Sense Amplifier (IADAPT) when adapter is not detected and ACDET pin is <0.6 V - allows lower battery discharge current. Logic high keeps IADAPT current-sense amplifier on when adapter is not detected and ACDET pin is <0.6 V - this allows measuring battery discharge current. AGND 9 Analog ground. On PCB layout, connect to the analog ground plane, and only connect to PGND through the power pad underneath the IC. VREF 10 3.3-V regulated voltage output. Place a 1-µF ceramic capacitor from VREF to AGND pin close to the IC. This voltage could be used for ratiometric programming of voltage and current regulation. VDAC 11 Charge voltage set reference input. Connect the VREF or external DAC voltage source to the VDAC pin. Battery voltage, charge current, and input current are programmed as a ratio of the VDAC pin voltage versus the VADJ, SRSET, and ACSET pin voltages, respectively. Place resistor dividers from VDAC to VADJ, SRSET, and ACSET pins to AGND for programming. A DAC could be used by connecting the DAC supply to VDAC and connecting the output to VADJ, SRSET, or ACSET. VADJ 12 Charge voltage set input. The voltage ratio of VADJ voltage versus VDAC voltage programs the battery voltage regulation set-point. Program by connecting a resistor divider from VDAC to VADJ, to AGND; or, by connecting the output of an external DAC to VADJ, and connect the DAC supply to VDAC. VADJ connected to REGN programs the default of 4.2 V per cell. EXTPWR 13 Valid adapter active-low detect logic open-drain output. Pulled low when input voltage is above ACDET programmed threshold, OR input current is greater than 1.25 A with 10-mΩ sense resistor. Connect a 10-kΩ pullup resistor from EXTPWR pin to pullup supply rail. ISYNSET 14 Synchronous mode voltage set input. Place a resistor from ISYNSET to AGND to program the charge undercurrent threshold to force non-synchronous converter operation at low output current, and to prevent negative inductor current. Threshold should be set at greater than half of the maximum inductor ripple current (50% duty cycle). IADAPT 15 Adapter current sense amplifier output. IADAPT voltage is 20 times the differential voltage across ACP-ACN. Place a 100-pF or less ceramic decoupling capacitor from IADAPT to AGND. SRSET 16 Charge current set input. The voltage ratio of SRSET voltage versus VDAC voltage programs the charge current regulation set-point. Program by connecting a resistor divider from VDAC to SRSET to AGND; or by connecting the output of an external DAC to SRSET pin and connect the DAC supply to VDAC pin. BAT 17 Battery voltage remote sense. Directly connect a kelvin sense trace from the battery pack positive terminal to the BAT pin to accurately sense the battery pack voltage. Place a 0.1-µF capacitor from BAT to AGND close to the IC to filter high-frequency noise. SRN 18 Charge current sense resistor, negative input. An optional 0.1-µF ceramic capacitor is placed from SRN pin to AGND for common-mode filtering. An optional 0.1-µF ceramic capacitor is placed from SRN to SRP to provide differential-mode filtering. SRP 19 Charge current sense resistor, positive input. (See comments for SRN.) CELLS 20 2, 3 or 4 cells selection logic input. Logic low programs 3 cell. Logic high programs 4 cell. Floating programs 2 cell. LPMD ACDET ACSET LPREF Submit Documentation Feedback 5 bq24740 www.ti.com SLUS736 – DECEMBER 2006 Table 1. TERMINAL FUNCTIONS – 28-PIN QFN (continued) TERMINAL NAME NO. DESCRIPTION DPMDET 21 Dynamic power management (DPM) input current loop active, open-drain output status. Logic low indicates input current is being limited by reducing the charge current. Connect 10-kΩ pullup resistor from DPMDET to VREF or a different pullup-supply rail. PGND 22 Power ground. On PCB layout, connect directly to source of low-side power MOSFET, to ground connection of input and output capacitors of the charger. Only connect to AGND through the power pad underneath the IC. LODRV 23 PWM low side driver output. Connect to the gate of the low-side power MOSFET with a short trace. REGN 24 PWM low side driver positive 6-V supply output. Connect a 1-µF ceramic capacitor from REGN to PGND, close to the IC. Use for high-side driver bootstrap voltage by connecting a small-signal Schottky diode from REGN to BTST. PH 25 PWM high side driver negative supply. Connect to the phase switching node (junction of the low-side power MOSFET drain, high-side power MOSFET source, and output inductor). Connect the 0.1-µF bootstrap capacitor from from PH to BTST. HIDRV 26 PWM high side driver output. Connect to the gate of the high-side power MOSFET with a short trace. BTST 27 PWM high side driver positive supply. Connect a 0.1-µF bootstrap ceramic capacitor from BTST to PH. Connect a small bootstrap Schottky diode from REGN to BTST. PVCC 28 IC power positive supply. Connect to the common-source (diode-OR) point: source of high-side P-channel MOSFET and source of reverse-blocking power P-channel MOSFET. Place a 1-µF ceramic capacitor from PVCC to PGND pin close to the IC. ABSOLUTE MAXIMUM RATINGS over operating free-air temperature range (unless otherwise noted) (1) (2) VALUE PVCC, ACP, ACN, SRP, SRN, BAT Voltage range Maximum difference voltage –1 to 30 REGN, LODRV, VADJ, ACSET, SRSET, ACDET, ISYNSET, LPMD, LPREF, CHGEN, CELLS, EXTPWR, DPMDET –0.3 to 7 VDAC –0.3 to 5.5 VREF –0.3 to 3.6 BTST, HIDRV with respect to AGND and PGND, IADAPT –0.3 to 36 ACP–ACN, SRP–SRN, AGND–PGND –0.5 to 0.5 –40 to 155 Storage temperature range –55 to 155 (2) 6 –0.3 to 30 PH Junction temperature range (1) UNIT V °C Stresses beyond those listed under absolute maximum ratings may cause permanent damage to the device. These are stress ratings only, and functional operation of the device at these or any other conditions beyond those indicated under recommended operating conditions is not implied. Exposure to absolute-maximum-rated conditions for extended periods may affect device reliability. All voltages are with respect to GND if not specified. Currents are positive into, negative out of the specified terminal. Consult Packaging Section of the data book for thermal limitations and considerations of packages. Submit Documentation Feedback bq24740 www.ti.com SLUS736 – DECEMBER 2006 RECOMMENDED OPERATING CONDITIONS over operating free-air temperature range (unless otherwise noted) MIN PH NOM MAX –1 24 PVCC, ACP, ACN, SRP, SRN, BAT 0 24 REGN, LODRV 0 6.5 VREF 0 3.3 VDAC, IADAPT 0 3.6 ACSET, SRSET, ACDET, ISYNSET, LPMD, LPREF, CHGEN, CELLS, EXTPWR, DPMDET 0 5.5 VADJ 0 6.5 BTST, HIDRV with respect to AGND and PGND 0 30 –0.3 0.3 Junction temperature range –40 125 Storage temperature range –55 150 Voltage range AGND, PGND Maximum difference voltage: ACP–ACN, SRP–SRN UNIT V 5.5 °C PACKAGE THERMAL DATA θJA TA = 70°C POWER RATING DERATING FACTOR ABOVE TA = 25°C 39°C/W 2.36W 0.028 W/°C PACKAGE QFN– (1) RHD (1) This data is based on using the JEDEC High-K board and the exposed die pad is connected to a Cu pad on the board. This is connected to the ground plane by a 2x3 via matrix. ELECTRICAL CHARACTERISTICS 7.0 V ≤ VPVCC≤ 24 V, 0°C < TJ < +125°C, typical values are at TA = 25°C, with respect to AGND (unless otherwise noted) PARAMETER TEST CONDITIONS MIN TYP MAX UNIT 24.0 V OPERATING CONDITIONS VPVCC_OP PVCC Input voltage operating range 5.0 CHARGE VOLTAGE REGULATION VBAT_REG_RNG BAT voltage regulation range VVDAC_OP VDAC reference voltage range VADJ_OP VADJ voltage range 4V-4.512V per cell, times 2,3,4 cell Charge voltage regulation accuracy Charge voltage regulation set to default to 4.2 V per cell 8 18 V 2.6 3.6 V V 0 REGN 8 V, 8.4 V, 9.024 V –0.5 0.5 12 V, 12.6 V, 13.536 V –0.5 0.5 16 V, 16.8 V, 18.048 V –0.5 0.5 VADJ connected to REGN, 8.4 V, 12.6 V, 16.8 V –0.5 0.5 0 100 0 VDAC VIREG_CHG = 40–100 mV –3 3 VIREG_CHG = 20 mV –5 5 VIREG_CHG = 5 mV –25 25 VIREG_CHG = 1.5 mV –33 33 % % CHARGE CURRENT REGULATION VIREG_CHG Charge current regulation differential voltage range VSRSET_OP SRSET voltage range Charge current regulation accuracy VIREG_CHG = VSRP– VSRN Submit Documentation Feedback mV V % 7 bq24740 www.ti.com SLUS736 – DECEMBER 2006 ELECTRICAL CHARACTERISTICS (continued) 7.0 V ≤ VPVCC≤ 24 V, 0°C < TJ < +125°C, typical values are at TA = 25°C, with respect to AGND (unless otherwise noted) PARAMETER TEST CONDITIONS MIN TYP MAX UNIT mV INPUT CURRENT REGULATION VIREG_DPM Adapter current regulation differential voltage range VACSET_OP ACSET voltage range Input current regulation accuracy VIREG_DPM = VACP– VACN 0 200 0 2 VIREG_DPM = 40–100 mV –3 3 VIREG_DPM = 20 mV –5 5 VIREG_DPM = 5 mV –25 25 VIREG_DPM = 1.5 mV –33 33 V % VREF REGULATOR VVREF_REG VREF regulator voltage VACDET > 0.6 V, 0-30 mA 3.267 IVREF_LIM VREF current limit VVREF = 0 V, VACDET > 0.6 V 35 3.3 3.333 V 75 mA 6.2 V REGN REGULATOR VREGN_REG REGN regulator voltage VACDET > 0.6 V, 0-75 mA, PVCC > 10 V 5.6 5.9 IREGN_LIM REGN current limit VREGN = 0 V, VACDET > 0.6 V 90 135 mA 0 24 V ADAPTER CURRENT SENSE AMPLIFIER VACP/N_OP Input common mode range Voltage on ACP/SRN VIADAPT IADAPT output voltage range 0 2 V IIADAPT IADAPT output current 0 1 mA AIADAPT Current sense amplifier voltage gain Adapter current sense accuracy AIADAPT = VIADAPT / VIREG_DPM 20 V/V VIREG_DPM = 40–100 mV –2 VIREG_DPM = 20 mV –3 3 VIREG_DPM = 5 mV –25 25 VIREG_DPM = 1.5 mV –30 30 IIADAPT_LIM Output current limit VIADAPT = 0 V CIADAPT_MAX Maximum output load capacitance For stability with 0 mA to 1 mA load 2 1 % mA 100 pF 24 V 2.424 V ACDET COMPARATOR VPVCC-BAT_OP Differential Voltage from PVCC to BAT VACDET_CHG ACDET adapter-detect rising threshold VACDET_CHG_HYS ACDET falling hysteresis VACDET_BIAS –20 Min voltage to enable charging, VACDET rising 2.40 518 700 VACDET falling ACDET rising deglitch (1) VACDET rising ACDET falling deglitch VACDET falling ACDET enable-bias rising threshold Min voltage to enable all bias, VACDET rising VACDET_BIAS_HYS Adapter present falling hysteresis ACDET rising deglitch 2.376 (1) ACDET falling deglitch 40 mV 908 0.56 0.62 VACDET falling 20 VACDET rising 10 VACDET falling 10 ms µs 10 0.68 V mV µs INPUT OVERVOLTAGE COMPARATOR (ACOV) VACOV AC Over-voltage rising threshold on ACDET (See ACDET in erminal Functions) VACOV_HYS AC Over-voltage rising deglitch 1.3 AC Over-voltage falling deglitch 1.3 (1) 8 Verified by design. Submit Documentation Feedback 3.007 3.1 3.193 V ms bq24740 www.ti.com SLUS736 – DECEMBER 2006 ELECTRICAL CHARACTERISTICS (continued) 7.0 V ≤ VPVCC≤ 24 V, 0°C < TJ < +125°C, typical values are at TA = 25°C, with respect to AGND (unless otherwise noted) PARAMETER TEST CONDITIONS MIN TYP MAX UNIT 200 250 300 mV AC CURRENT DETECT COMPARATOR (INPUT UNDER_CURRENT) VACIDET Adapter current detect rising threshold VACI = IAC× RAC× 20, falling edge VACIDET_HYS Adapter current detect hysteresis Rising edge 50 mV PVCC / BAT COMPARATOR (REVERSE DISCHARGING PROTECTION) VPVCC-BAT_FALL PVCC to BAT falling threshold VPVCC-BAT__HYS PVCC to BAT hysteresis VPVCC– VBAT to turn off ACFET 140 185 240 50 PVCC to BAT Rising Deglitch VPVCC– VBAT > VPVCC-BAT_RISE 10 PVCC to BAT Falling Deglitch VPVCC– VBAT < VPVCC-BAT_FALL 6 mV mV µs INPUT UNDERVOLTAGE LOCK-OUT COMPARATOR (UVLO) VUVLO AC Under-voltage rising threshold Measure on PVCC VUVLO_HYS AC Under-voltage hysteresis, falling 3.5 4 4.5 260 V mV BAT OVER-VOLTAGE COMPARATOR VOV_RISE VOV_FALL Over-voltage rising threshold (2) Over-voltage falling threshold (2) 104 As percentage of VBAT_REG % 102 CHARGE OVER-CURRENT COMPARATOR VOC Charge over-current falling threshold As percentage of IREG_CHG Minimum Current Limit (SRP-SRN) 145 % 50 mV INPUT CURRENT LOW-POWER MODE COMPARATOR VACLP_HYS AC low power hysteresis VACLP_OFFSET AC low power rising threshold 2.8 mV 1 THERMAL SHUTDOWN COMPARATOR TSHUT Thermal shutdown rising temperature TSHUT_HYS Thermal shutdown hysteresis, falling Temperature Increasing 155 °C 20 PWM HIGH SIDE DRIVER (HIDRV) RDS_HI_ON High side driver turn-on resistance VBTST– VPH = 5.5 V, tested at 100 mA 3 6 RDS_HI_OFF High side driver turn-off resistance VBTST– VPH = 5.5 V, tested at 100 mA 0.7 1.4 VBTST_REFRESH Bootstrap refresh comparator threshold voltage VBTST– VPH when low side refresh pulse is requested 4 Ω V PWM LOW SIDE DRIVER (LODRV) RDS_LO_ON Low side driver turn-on resistance REGN = 6 V, tested at 100 mA 3 6 RDS_LO_OFF Low side driver turn-off resistance REGN = 6 V, tested at 100 mA 0.6 1.2 Ω PWM DRIVERS TIMING Driver Dead Time — Dead time when switching between LODRV and HIDRV. No load at LODRV and HIDRV 30 ns PWM OSCILLATOR FSW PWM switching frequency VRAMP_HEIGHT PWM ramp height (2) 240 As percentage of PVCC 360 6.6 kHz %PVCC Verified by design. Submit Documentation Feedback 9 bq24740 www.ti.com SLUS736 – DECEMBER 2006 ELECTRICAL CHARACTERISTICS (continued) 7.0 V ≤ VPVCC≤ 24 V, 0°C < TJ < +125°C, typical values are at TA = 25°C, with respect to AGND (unless otherwise noted) PARAMETER TEST CONDITIONS MIN TYP MAX VBAT = 16.8 V, VACDET < 0.6 V, VPVCC > 5 V, TJ = 85°C 7 10 VBAT = 16.8 V, VACDET < 0.6 V, VPVCC > 5 V, TJ = 125°C 7 11 UNIT QUIESCENT CURRENT IOFF_STATE Total off-state battery current from SRP, SRN, BAT, VCC, BTST, PH, etc. µA IBAT_ON Battery on-state quiescent current VBAT = 16.8V, 0.6V < VACDET < 2.4V, VPVCC > 5V 1 IBAT_LOAD_CD Internal battery load current, charge disbled Charge is disabled: VBAT = 16.8 V, VACDET > 2.4 V, VPVCC > 5 V 3 5 mA IBAT_LOAD_CE Internal battery load current, charge enabled Charge is enabled: VBAT = 16.8 V, VACDET > 2.4 V, VPVCC > 5 V 10 12 mA IAC Adapter quiescent current VPVCC = 20 V, charge disabled 2.8 4 mA IAC_SWITCH Adapter switching quiescent current VPVCC = 20 V, Charge enabled, converter running, total gate charge = 2 × 10 nC 25 mA 8 step 1.7 ms 6 mA INTERNAL SOFT START (8 steps to regulation current) Soft start steps Soft start step time CHARGER SECTION POWER-UP SEQUENCING Charge-enable delay after power-up Delay from when adapter is detected to when the charger is allowed to turn on 518 700 908 ms ISYNSET AMPLIFIER AND COMPARATOR (SYNCHRONOUS TO NON-SYSNCHRONOUS TRANSITION) AISYNSET Accuracy 5 mV Gain ISYNSET amplifier gain –20 % V/I 1 V ISYNSET rising deglitch 20 µs ISYNSET falling deglitch 640 µs ISYNSET pin voltage VISYNSET 20 250 LOGIC IO PIN CHARACTERISTICS (CHGEN, IADSLP ) VIN_LO Input low threshold voltage VIN_HI Input high threshold voltage VBIAS Input bias current 0.8 V 1 µA 2.1 VCHGEN = 0 to VREGN LOGIC INPUT PIN CHARACTERISTICS (CELLS) VIN_LO Input low threshold voltage, 3 cells CELLS voltage falling edge VIN_MID Input mid threshold voltage, 2 cells CELLS voltage rising for MIN, CELLS voltage falling for MAX 0.8 0.5 VIN_HI Input high threshold voltage, 4 cells CELLS voltage rising 2.5 IBIAS_FLOAT Input bias float current for 2-cell selection V = 0 to V –1 1.8 1 V µA OPEN-DRAIN LOGIC OUTPUT PIN CHARACTERISTICS (EXTPWR) VOUT_LO Output low saturation voltage Sink Current = 4 mA Delay, EXTPWR falling 518 Delay, EXTPWR rising 700 0.5 V 908 ms µs 10 OPEN-DRAIN LOGIC OUTPUT PIN CHARACTERISTICS (DPMDET, LPMD) VOUT_LO Output low saturation voltage Sink Current = 5 mA Delay, rising/falling 10 0.5 10 Submit Documentation Feedback V ms bq24740 www.ti.com SLUS736 – DECEMBER 2006 TYPICAL CHARACTERISTICS Table of Graphs (1) Y X FIgure VREF Load and Line Regulation vs Load Current Figure 4 REGN Load and Line Regulation vs Load Current Figure 5 BAT Voltage vs VADJ/VDAC Ratio Figure 6 Charge Current vs SRSET/VDAC Ratio Figure 7 Input Current vs ACSET/VDAC Ratio Figure 8 BAT Voltage Regulation Accuracy vs Charge Current Figure 9 BAT Voltage Regulation Accuracy Figure 10 Charge Current Regulation Accuracy Figure 11 Input Current Regulation (DPM) Accuracy Figure 12 VIADAPT Input Current Sense Amplifier Accuracy Figure 13 Input Regulation Current (DPM), and Charge Current vs System Current Figure 14 Transient System Load (DPM) Response Figure 15 Charge Current Regulation vs BAT Voltage Figure 16 Efficiency vs Battery Charge Current Figure 17 Battery Removal (from Constant Current Mode) Figure 18 REF and REGN Startup Figure 19 Charger on Adapter Removal Figure 20 Charge Enable / Disable and Current Soft-Start Figure 21 Nonsynchronous to Synchronous Transition Figure 22 Synchronous to Nonsynchronous Transition Figure 23 Near 100% Duty Cycle Bootstrap Recharge Pulse Figure 24 Battery Shorted Charger Response, Over Current Protection (OCP) and Charge Current Regulation Figure 25 Continuous Conduction Mode (CCM) Switching Waveforms Figure 26 Discontinuous Conduction Mode (DCM) Switching Waveforms Figure 27 Test results based on Figure 2 application schematic. VIN = 20 V, VBAT = 3-cell LiIon, ICHG = 3 A, IADAPTER_LIMIT = 4 A, TA = 25°C, unless otherwise specified. VREF LOAD AND LINE REGULATION vs Load Current REGN LOAD AND LINE REGULATION vs LOAD CURRENT 0 0.50 0.40 -0.50 Regulation Error - % Regulation Error - % (1) 0.30 PVCC = 10 V 0.20 0.10 0 -1 -1.50 PVCC = 10 V -2 PVCC = 20 V -0.10 -2.50 -0.20 -3 PVCC = 20 V 0 10 20 30 VREF - Load Current - mA 40 50 0 Figure 4. 10 20 30 40 50 60 REGN - Load Current - mA 70 80 Figure 5. Submit Documentation Feedback 11 bq24740 www.ti.com SLUS736 – DECEMBER 2006 BAT VOLTAGE vs VADJ/VDAC RATIO CHARGE CURRENT vs SRSET/VDAC RATIO 10 18.2 VADJ = 0 -VDAC, 4-Cell, No Load Voltage Regulation - V 17.8 SRSET Varied, 4-Cell, Vbat = 16 V 9 Charge Current Regulation - A 18 17.6 17.4 17.2 17 16.8 16.6 16.4 8 7 6 5 4 3 2 1 16.2 0 16 0 0.1 0.2 0.3 0.4 0.5 0.6 0.7 0.8 0.9 0 1 0.1 0.2 0.3 VADJ/VDAC Ratio 0.8 0.9 Figure 6. Figure 7. INPUT CURRENT vs ACSET/VDAC RATIO BAT VOLTAGE REGULATION ACCURACY vs CHARGE CURRENT 1 0.2 10 ACSET Varied, 4-Cell, Vbat = 16 V 8 Vreg = 16.8 V 0.1 Regulation Error - % 9 Input Current Regulation - A 0.4 0.5 0.6 0.7 SRSET/VDAC Ratio 7 6 5 4 3 0 -0.1 2 1 -0.2 0 0 0.1 0.2 0.3 0.4 0.5 0.6 0.7 ACSET/VDAC Ratio 0.8 0.9 0 1 2000 Figure 8. BAT VOLTAGE REGULATION ACCURACY CHARGE CURRENT REGULATION ACCURACY 4-Cell, VBAT = 16 V 1 VADJ = 0 -VDAC SRSET Varied 0 -1 0.04 Regulation Error - % Regulation Error - % 8000 2 0.06 4-Cell, no load 0.02 0 -0.02 -0.04 -0.06 -0.10 16.5 -2 -3 -4 -5 -6 -7 -8 -0.08 -9 -10 17 17.5 18 18.5 19 0 V(BAT) - Setpoint - V Figure 10. 12 6000 Figure 9. 0.10 0.08 4000 Charge Current - mA 2 4 I(CHRG) - Setpoint - A Figure 11. Submit Documentation Feedback 6 8 bq24740 www.ti.com SLUS736 – DECEMBER 2006 INPUT CURRENT REGULATION (DPM) ACCURACY VIADAPT INPUT CURRENT SENSE AMPLIFIER ACCURACY 5 10 ACSET Varied 9 0 7 4-Cell, VBAT = 16 V 6 Percent Error Regulation Error - % 8 5 4 3 2 VI = 20 V, CHG = EN -5 VI = 20 V, CHG = DIS -10 -15 1 0 -20 -1 -2 -25 Iadapt Amplifier Gain 0 1 2 3 4 Input Current Regulation Setpoint - A 5 0 6 1 2 3 4 5 6 I(ACPWR) - A 7 8 9 10 Figure 12. Figure 13. INPUT REGULATION CURRENT (DPM), AND CHARGE CURRENT vs SYSTEM CURRENT TRANSIENT SYSTEM LOAD (DPM) RESPONSE 5 VI = 20 V, 4-Cell, Vbat = 16 V 4 Ichrg and Iin - A Input Current 3 Charge Current 2 1 0 0 1 2 System Current - A 3 4 Figure 14. Figure 15. CHARGE CURRENT REGULATION vs BAT VOLTAGE EFFICIENCY vs BATTERY CHARGE CURRENT 5 100 V(BAT) = 16.8 V Efficiency - % Charge Current - A 4 3 2 90 Vreg = 12.6 V Vreg = 8.4 V 80 1 Ichrg_set = 4 A 70 0 0 2 4 6 8 10 12 Battery Voltage - V 14 16 18 0 Figure 16. 2000 6000 4000 Battery Charge Current - mA 8000 Figure 17. Submit Documentation Feedback 13 bq24740 www.ti.com SLUS736 – DECEMBER 2006 14 BATTERY REMOVAL REF AND REGN STARTUP Figure 18. Figure 19. CHARGER ON ADAPTER REMOVAL CHARGE ENABLE / DISABLE AND CURRENT SOFT-START Figure 20. Figure 21. NONSYNCHRONOUS TO SYNCHRONOUS TRANSITION SYNCHRONOUS TO NONSYNCHRONOUS TRANSITION Figure 22. Figure 23. Submit Documentation Feedback bq24740 www.ti.com SLUS736 – DECEMBER 2006 NEAR 100% DUTY CYCLE BOOTSTRAP RECHARGE PULSE BATTERY SHORTED CHARGER RESPONSE, OVERCURRENT PROTECTION (OCP) AND CHARGE CURRENT REGULATION Figure 24. Figure 25. CONTINUOUS CONDUCTION MODE (CCM) SWITCHING WAVEFORMS DISCONTINUOUS CONDUCTION MODE (DCM) SWITCHING WAVEFORMS Figure 26. Figure 27. Submit Documentation Feedback 15 bq24740 www.ti.com SLUS736 – DECEMBER 2006 FUNCTIONAL BLOCK DIAGRAM ENA_BIAS_CMP - 0.6V 700 ms AC VGOOD - 2.4V + ACDET 3.3V LDO VREF ENA_BIAS V(IADAPT) EAO EAI EXTPWR Delay Rising + + AC IGOOD CHGEN - PVCC 250mV +- /IADSLP IADSLP ACP PVCC FBO + V(ACP-ACN) - IIN_REG - IIN_ER COMP ERROR AMPLIFIER + ACN BTST CHGEN + 1V BAT VBAT_REG 10mA LEVEL SHIFTER BAT_ER + 20 mA CHRG_ON HIDRV BAT_SHORT ACOP SRP + 20X - IBAT_ REG + SRN PH DC-DC CONVERTER PWM LOGIC V(SRP-SRN) ICH_ER PVCC 6V LDO 20 mA REGN SYNCH V(SRP - SRN) + SYNCH ENA_BIAS ISYNSET BTST - REFRESH C BTST LODRV + BAT ACSET – 4V + _ BAT_SHORT PH + 2.9 V/Cell +- IC Tj 155°C + PGND TSHUT – ACP SRSET VBATSET IBATSET IINSET VADJ – V(IADAPT) + 104% X VBAT_REG – V(SRP-SRN) + 145% X IBAT_REG – ACDET + 3.1V +- 2, 3, 4 LPREF LPMD IBAT_REG RATIO IIN_REG PROGRAM VDAC CELLS VBAT_REG BAT PVCC + BAT_OVP ACN + 20x - V(IADAPT) CHG_OCP ACOV DPMDET DPM_LOOP_ON – – UVLO + AGND 4 V +- bq24740 16 IADAPT Submit Documentation Feedback bq24740 www.ti.com SLUS736 – DECEMBER 2006 TYPICAL APPLICATIONS DETAILED DESCRIPTION BATTERY VOLTAGE REGULATION The bq24740 uses a high-accuracy voltage regulator for charging voltage. Internal default battery voltage setting VBATT=4.2 V × cell count. The regulation voltage is ratio-metric with respect to VADC. The ratio of VADJ and VDAC provides extra 12.5% adjust range on VBATT regulation voltage. By limiting the adjust range to 12.5% of the regulation voltage, the external resistor mismatch error is reduced from ±1% to ±0.1%. Therefore, an overall voltage accuracy as good as 0.5% is maintained, while using 1% mis-match resistors. Ratio-metric conversion also allows compatibility with D/As or microcontrollers (µC). The battery voltage is programmed through VADJ and VDAC using Equation 1. V BATT + cell count ƪ ǒ Ǔƫ VVADJ V VDAC 4V ) 0.5 (1) The input voltage range of VDAC is between 2.6 V and 3.6 V. VADJ is set between 0 and VDAC. VBATT defaults to 4.2 V × cell count when VADJ is connected to REGN. CELLS pin is the logic input for selecting cell count. Connect CELLS to charge 2,3, or 4 Li+ cells. When charging other cell chemistries, use CELLS to select an output voltage range for the charger. CELLS CELL COUNT Float 2 AGND 3 VREF 4 The per-cell battery termination voltage is function of the battery chemistry. Consult the battery manufacturer to determine this voltage. The BAT pin is used to sense the battery voltage for voltage regulation and should be connected as close to the battery as possible, or directly on the output capacitor. A 0.1-µF ceramic capacitor from BAT to AGND is recommended to be as close to the BAT pin as possible to decouple high frequency noise. BATTERY CURRENT REGULATION The SRSET input sets the maximum charging current. Battery current is sensed by resistor RSR connected between SRP and SRN. The full-scale differential voltage between SRP and SRN is 100 mV. Thus, for a 0.010 Ω sense resistor, the maximum charging current is 10 A. SRSET is ratio-metric with respect to VDAC using Equation 2: V I CHARGE + SRSET 0.10 VVDAC R SR (2) The input voltage range of SRSET is between 0 and VDAC, up to 3.6 V. The SRP and SRN pins are used to sense across RSR with default value of 10 mΩ. However, resistors of other values can also be used. For a larger the sense resistor, you get a larger sense voltage, and a higher regulation accuracy; but, at the expense of higher conduction loss. INPUT ADAPTER CURRENT REGULATION The total input from an AC adapter or other DC sources is a function of the system supply current and the battery charging current. System current normally fluctuates as portions of the systems are powered up or down. Without Dynamic Power Management (DPM), the source must be able to supply the maximum system current and the maximum charger input current simultaneously. By using DPM, the input current regulator reduces the charging current when the input current exceeds the input current limit set by ACSET. The current capability of the AC adapter can be lowered, reducing system cost. Similar to setting battery regulation current, adapter current is sensed by resistor RAC connected between ACP and ACN. Its maximum value is set ACSET, which is ratio-metric with respect to VDAC, using Equation 3. Submit Documentation Feedback 17 bq24740 www.ti.com SLUS736 – DECEMBER 2006 I ADAPTER + VACSET VVDAC 0.10 R AC (3) The input voltage range of ACSET is between 0 and VDAC, up to 3.6 V. The ACP and ACN pins are used to sense RAC with default value of 10mΩ. However, resistors of other values can also be used. For a larger the sense resistor, you get a larger sense voltage, and a higher regulation accuracy; but, at the expense of higher conduction loss. ADAPTER DETECT AND POWER UP An external resistor voltage divider attenuates the adapter voltage before it goes to ACDET. The adapter detect threshold should typically be programmed to a value greater than the maximum battery voltage and lower than the minimum allowed adapter voltage. The ACDET divider should be placed before the ACFET in order to sense the true adapter input voltage whether the ACFET is on or off. Before adapter is detected, BATFET stays on and ACFET turns off. If PVCC is below 5 V, the device is disabled, and both ACFET and BATFET turn off. If ACDET is below 0.6 V but PVCC is above 5 V, part of the bias is enabled, including a crude bandgap reference, ACFET drive and BATFET drive. IADAPT is disabled and pulled down to GND. The total quiescent current is less than 10µA. Once ACDET rises above 0.6 V and PVCC is above 5 V, all the bias circuits are enabled and REGN output goes to 6 V and VREF goes to 3.3 V. IADAPT becomes valid to proportionally reflect the adapter current. When ACDET keeps rising and passes 2.4 V, a valid AC adapter is present. 500ms later, the following occurs: • ACGOOD becomes high through external pull-up resistor to the host digital voltage rail; • Charger turns on if all the conditions are satisfied and STAT becomes valid. (refer to Enable and Disable Charging) ENABLE AND DISABLE CHARGING The following conditions have to be valid before charge is enabled: • CHGEN is LOW; • Adapter is detected; • Adapter is higher than PVCC-BAT threshold; • Adapter is not over voltage; • 500ms delay is complete after adapter detected; • REGNGOOD and VREFGOOD are valid; • Thermal Shut (TSHUT) is not valid; One of the following conditions will stop on-going charging: • CHGEN is HIGH; • Adapter is removed; • Adapter is less than 250mV above battery; • Adapter is over voltage; • Adapter is over current; • TSHUT IC temperature threshold is reached (145°C on rising-edge with 15°C hysteresis). AUTOMATIC INTERNAL SOFT-START CHARGER CURRENT The charger automatically soft-starts the charger regulation current every time the charger is enabled to ensure there is no overshoot or stress on the output capacitors or the power converter. The soft-start consists of stepping-up the charge regulation current into 8 evenly divided steps up to the programmed charge current. Each step lasts around 1ms, for a typical rise time of 8 ms. No external components are needed for this function. 18 Submit Documentation Feedback bq24740 www.ti.com SLUS736 – DECEMBER 2006 CONVERTER OPERATION The synchronous buck PWM converter uses a fixed frequency (300 kHz) voltage mode with feed-forward control scheme. A type III compensation network allows using ceramic capacitors at the output of the converter. The compensation input stage is connected internally between the feedback output (FBO) and the error amplifier input (EAI). The feedback compensation stage is connected between the error amplifier input (EAI) and error amplifier output (EAO). The LC output filter is selected to give a resonant frequency of 8–12.5 kHz nominal. fo + Where resonant frequency, fo, is given by: • CO = C11 + C12 • LO = L1 1 2p ǸLoC o where (from Figure 1 schematic) An internal saw-tooth ramp is compared to the internal EAO error control signal to vary the duty-cycle of the converter. The ramp height is one-fifteenth of the input adapter voltage making it always directly proportional to the input adapter voltage. This cancels out any loop gain variation due to a change in input voltage, and simplifies the loop compensation. The ramp is offset by 250 mV in order to allow zero percent duty-cycle, when the EAO signal is below the ramp. The EAO signal is also allowed to exceed the saw-tooth ramp signal in order to get a 100% duty-cycle PWM request. Internal gate drive logic allows achieving 99.98% duty-cycle while ensuring the N-channel upper device always has enough voltage to stay fully on. If the BTST pin to PH pin voltage falls below 4 V for more than 3 cycles, then the high-side n-channel power MOSFET is turned off and the low-side n-channel power MOSFET is turned on to pull the PH node down and recharge the BTST capacitor. Then the high-side driver returns to 100% duty-cycle operation until the (BTST-PH) voltage is detected to fall low again due to leakage current discharging the BTST capacitor below the 4 V, and the reset pulse is reissued. The 300 kHz fixed frequency oscillator keeps tight control of the switching frequency under all conditions of input voltage, battery voltage, charge current, and temperature, simplifying output filter design and keeping it out of the audible noise region. The charge current sense resistor RSR should be placed with at least half or more of the total output capacitance placed before the sense resistor contacting both sense resistor and the output inductor; and the other half or remaining capacitance placed after the sense resistor. The output capacitance should be divided and placed onto both sides of the charge current sense resistor. A ratio of 50:50 percent gives the best performance; but the node in which the output inductor and sense resistor connect should have a minimum of 50% of the total capacitance. This capacitance provides sufficient filtering to remove the switching noise and give better current sense accuracy. The type III compensation provides phase boost near the cross-over frequency, giving sufficient phase margin. SYNCHRONOUS AND NON-SYNCHRONOUS OPERATION The charger operates in non-synchronous mode when the sensed charge current is below the ISYNSET value. Otherwise, the charger operates in synchronous mode. During synchronous mode, the low-side n-channel power MOSFET is on, when the high-side n-channel power MOSFET is off. The internal gate drive logic ensures there is break-before-make switching to prevent shoot-through currents. During the 30ns dead time where both FETs are off, the back-diode of the low-side power MOSFET conducts the inductor current. Having the low-side FET turn-on keeps the power dissipation low, and allows safely charging at high currents. During synchronous mode the inductor current is always flowing and operates in Continuous Conduction Mode (CCM), creating a fixed two-pole system. During non-synchronous operation, after the high-side n-channel power MOSFET turns off, and after the break-before-make dead-time, the low-side n-channel power MOSFET will turn-on for around 80ns, then the low-side power MOSFET will turn-off and stay off until the beginning of the next cycle, where the high-side power MOSFET is turned on again. The 80ns low-side MOSFET on-time is required to ensure the bootstrap capacitor is always recharged and able to keep the high-side power MOSFET on during the next cycle. This is important for battery chargers, where unlike regular dc-dc converters, there is a battery load that maintains a voltage and can both source and sink current. The 80-ns low-side pulse pulls the PH node (connection between high and low-side MOSFET) down, allowing the bootstrap capacitor to recharge up to the REGN LDO value. After the 80 ns, the low-side MOSFET is kept off to prevent negative inductor current from occurring. The inductor current is blocked by the off low-side MOSFET, and the inductor current will become discontinuous. This mode is called Discontinuous Conduction Mode (DCM). Submit Documentation Feedback 19 bq24740 www.ti.com SLUS736 – DECEMBER 2006 During the DCM mode the loop response automatically changes and has a single pole system at which the pole is proportional to the load current, because the converter does not sink current, and only the load provides a current sink. This means at very low currents the loop response is slower, as there is less sinking current available to discharge the output voltage. At very low currents during non-synchronous operation, there may be a small amount of negative inductor current during the 80 ns recharge pulse. The charge should be low enough to be absorbed by the input capacitance. Whenever the converter goes into 0% duty-cycle mode, and BTST – PH < 4 V, the 80-ns recharge pulse occurs on LODRV, the high-side MOSFET does not turn on, and the low-side MOSFET does not turn on (no 80-ns recharge pulse), and there is no discharge from the battery. ISYNSET CONTROL (CHARGE UNDER-CURRENT) In bq24740, ISYN is internally set as the charge current threshold at which the charger changes from non-synchronous operation into synchronous operation. The low side driver turns on for only 80 ns to charge the boost cap. This is important to prevent negative inductor current, which may cause a boost effect in which the input voltage increases as power is transferred from the battery to the input capacitors. This can lead to an over-voltage on the PVCC node and potentially cause some damage to the system. This programmable value allows setting the current threshold for any inductor current ripple, and avoiding negative inductor current. The minimum synchronous threshold should be set from ½ the inductor current ripple to the full ripple current, where the inductor current ripple is given by I RIPPLE_MAX v I SYN v I RIPPLE_MAX 2 ǒVIN_MAX * VBAT_MINǓ and I RIPPLE_MAX + ǒ Ǔ ǒǓ VBAT_MIN VIN_MAX 1 fs LMIN (4) where VIN_MAX: maximum adapter voltage VBAT_MIN: minimum BAT voltage fS: switching frequency LMIN: minimum output inductor The ISYNSET comparator, or charge under-current comparator, compares the voltage between SRP-BAT and internal threshold on the cycle-to-cycle base. The threshold is set to 13 mV on the falling edge with 8 mV hysteresis on the rising edge with 10% variation. HIGH ACCURACY IADAPT USING CURRENT SENSE AMPLIFIER (CSA) An industry standard, high accuracy current sense amplifier (CSA) is used to monitor the input current by the host or some discrete logic through the analog voltage output of the IADAPT pin. The CSA amplifies the input sensed voltage of ACP – ACN by 20x through the IADAPT pin. The IADAPT output is a voltage source 20 times the input differential voltage. Once PVCC is above 5 V and ACDET is above 0.6V, IADAPT no longer stays at ground, but becomes active. If the user wants to lower the voltage, they could use a resistor divider from IOUT to AGND, and still achieve accuracy over temperature as the resistors can be matched their thermal coefficients. A 200-pF capacitor connected on the output is recommended for decoupling high-frequency noise. An additional RC filter is optional, after the 200-pF capacitor, if additional filtering is desired. Note that adding filtering also adds additional response delay. INPUT OVER VOLTAGE PROTECTION (ACOV) ACOV provides when ACDET > and the battery resumes when threshold. 20 protection to prevent system damage due to high input voltage. The controller enters ACOV 3.1 V. Charge is disabled, the adapter is disconnected from the system by turning off ACDRV, is connected to the system by turning on BATDRV. ACOV is not latched—normal operation the ACDET voltage returns below 3.1 V. ACOV threshold is 130% of the adapter-detect Submit Documentation Feedback bq24740 www.ti.com SLUS736 – DECEMBER 2006 INPUT UNDER VOLTAGE LOCK OUT (UVLO) The system must have a minimum 5V PVCC voltage to allow proper operation. This PVCC voltage could come from either input adapter or battery, using a diode-OR input. When the PVCC voltage is below 5 V the bias circuits REGN and VREF stay inactive, even with ACDET above 0.6 V. INPUT CURRENT LOW-POWER MODE DETECTION In order to optimize the system performance, the HOST keeps an eye on the adapter current. Once the adapter current is above threshold set via LPREF, LPMD pin sends signal to HOST. The signal alarms the host that input power has exceeded the programmed limit, allowing the host to throttle back system power by reducing clock frequency, lowering rail voltages, or disabling certain parts of the system. The LPMD pin is an open-drain output. Connect a pull-up resistor to LPMD. The output is logic HI when the IADAPT output voltage (IADAPT = 20 x VACP-ACN) is lower than the LPREF input voltage. The LPREF threshold is set by an external resistor divider using VREF. A hysteresis can be programmed by a positive feedback resistor from LPMD pin to the LPREF pin. ACDET Comparator ACDET 2.4 V + - ACDET_DET t_dg ACDET_DG rising 700 ms TO ACDET Logic EXT_PWR_DG ACP 1 kW + LOIAC Comparator - ACN EXTPWR Adaptor Current Sense Amplifier 250 mV - LOIAC_DET + 20 kW IADAPT Error Amplifier Disable + IADAPT IADAPT Disable LOPWRMODE Comparator + LPREF LOPWR_DET LPMD Program Hysteresis of comparator by putting a resistor in feedback from LPMD pin to LPREF pin. Figure 28. EXTPWR, LPREF and LPMD Logic BATTERY OVER-VOLTAGE PROTECTION The converter stops switching when BAT voltage goes above 104% of the regulation voltage. The converter will not allow the high-side FET to turn on until the BAT voltage goes below 102% of the regulation voltage. This allows one-cycle response to an overvoltage condition, such as when the load is removed or the battery is disconnected. A 10-mA current sink from BAT to PGND is on only during charge, and allows discharging the stored output-inductor energy into the output capacitors. CHARGE OVER-CURRENT PROTECTION The charger has a secondary over-current protection. It monitors the charge current, and prevents the current from exceeding 145% of regulated charge current. The high-side gate drive turns off when the over-current is detected, and automatically resumes when the current falls below the over-current threshold. Submit Documentation Feedback 21 bq24740 www.ti.com SLUS736 – DECEMBER 2006 THERMAL SHUTDOWN PROTECTION The QFN package has low thermal impedance, which provides good thermal conduction from the silicon to the ambient, to keep junctions temperatures low. As added level of protection, the charger converter turns off and self-protects whenever the junction temperature exceeds the TSHUT threshold of 145°C. The charger stays off until the junction temperature falls below 130°C. Status Outputs (EXTPWR, LPMD, DPMDET pin) Four status outputs are available, and they all, except for LPMD, require external pull up resistors to pull the pins to system digital rail for a high level. EXTPWR open-drain output goes low under either of the two conditions: 1. ACDET is above 2.4 V 2. Adapter current is above 1.25 A using a 10-mΩ sense resistor (IADAPT voltage above 250 mV). Internally, the AC current detect comparator looks between IADAPT and an internal 250-mV threshold. It indicates a good adapter is connected because of valid voltage or current. STAT open-drain output goes low when charging. A high level on STAT indicates the charger is not charging; therefore, either, CHGEN pin is not low, or the charger is not able to charge because input voltage is still powering up and the 700-ms delay has not finished, or because of a fault condition such as overcurrent, input over voltage, or TSHUT over temperature. LPMD push-pull output goes low when the input current is higher than the programmed threshold via LPREF pin. Hysteresis can be programmed by putting a resistor from LPREF pin to LPMD pin. DPMDET open-drain output goes low when the DPM loop is active to reduce the battery charge current (after a 10-ms delay). Table 2. Component List for Typical System Circuit of Figure 1 PART DESIGNATOR QTY DESCRIPTION Q1, Q2, Q3 3 P-channel MOSFET, –30V,-6A, SO-8, Vishay-Siliconix, Si4435 Q4, Q2 2 N-channel MOSFET, 30V, 12.5A, SO-8, Fairchild, FDS6680A D1 1 Diode, Dual Schottky, 30V, 200mA, SOT23, Fairchild, BAT54C RAC, RSR 2 Sense Resistor, 10 mΩ, 1%, 1W, 2010, Vishay-Dale, WSL2010R0100F L1 1 Inductor, 10µH, 7A, 31mΩ, Vishay-Dale, IHLP5050FD-01 C1, C6, C7, C11, C12 5 Capacitor, Ceramic, 10µF, 35V, 20%, X5R, 1206, Panasonic, ECJ-3YB1E106M C4, C8, C10 3 Capacitor, Ceramic, 1µF, 25V, 10%, X7R, 2012, TDK, C2012X7R1E105K C2, C3, C9, C13, C14, C15 6 Capacitor, Ceramic, 0.1µF, 50V, 10%, X7R, 0805, Kemet, C0805C104K5RACTU R3, R4, R5 4 Resistor, Chip, 10 kΩ, 1/16W, 5%, 0402 R1 1 Resistor, Chip, 432 kΩ, 1/16W, 1%, 0402 R2 1 Resistor, Chip, 66.5 kΩ, 1/16W, 1%, 0402 R6 1 Resistor, Chip, 33 kΩ, 1/16W, 1%, 0402 R7 1 Resistor, Chip, 200 kΩ, 1/16W, 1%, 0402 R8 1 Resistor, Chip, 24.9 kΩ, 1/16W, 1%, 0402 R9 1 Resistor, Chip, 1.8 MΩ, 1/16W, 1%, 0402 22 Submit Documentation Feedback bq24740 www.ti.com SLUS736 – DECEMBER 2006 APPLICATION INFORMATION Input Capacitance Calculation During the adapter hot plug-in, the ACDRV has not been enabled. The AC switch is off and the simplified equivalent circuit of the input is shown in Figure 29. Ii Li Ri C1 Vi A. C8 Ci Vc Ri and Li are the equivalent input inductance and resistance. C1 and C8 are the input capacitance. Figure 29. Simplified Equivalent Circuit During Adapter Insertion The voltage on the input capacitor(s) is given by: VC ( t ) = VC (0) + Z0 = where Vi × w Z 0 × C i × w 20 Li w= Ci , + - Vi Z 0 × C i × w 02 æR 1 - çç i L i C i è 2L i e Ri t 2L i æ ö R çç - i sin wt - w × cos wt ÷÷ 2 L i è ø (5) 2 ö ÷÷ w0 = ø , and 1 L iCi Submit Documentation Feedback 23 bq24740 www.ti.com SLUS736 – DECEMBER 2006 APPLICATION INFORMATION (continued) For a typical notebook charger application, the total stray inductance of the adapter output wire and the PCB connections is normally 5–12 µH, and the total effective resistance of the input connections is 0.15–0.5 Ω. Figure 30(a) demonstrates that a higher Ci helps to damp the voltage spike. Figure 30(b) demonstrates the effect of the input stray inductance Li on the input voltage spike. The dashed curve in Figure 30(b) represents the worst case for Ci=40 µF. Figure 30(c) shows how the resistance helps to suppress the input voltage spike. 35 35 Ci = 20 mF Ci = 40 mF Ri = 0.15 W, Ci = 40 mF 30 Input Capacitor Voltage - V Input Capacitor Voltage - V Li = 5 mF Ri = 0.21 W, Li = 9.3 mH 30 25 20 15 10 5 Li = 12 mF 25 20 15 10 5 0 0 0.5 1 1.5 2 2.5 3 3.5 Time - ms (a) Vc with various Ci values 4 4.5 0 5 0 0.5 1 1.5 2 2.5 3 Time - ms 3.5 4 4.5 5 (b) Vc with various Li values 35 Li = 9.3 mH, Ci = 40 mF Ri = 0.15 W Input Capacitor Voltage - V 30 Ri = 0.50 W 25 20 15 10 5 0 0 0.5 1 1.5 2 2.5 3 Time - ms 3.5 4 4.5 5 (c) Vc with various Ri values Figure 30. Parametric Study Of The Input Voltage Minimizing the input stray inductance, increasing the input capacitance and using high-ESR input capacitors helps to suppress the input voltage spike. 24 Submit Documentation Feedback bq24740 www.ti.com SLUS736 – DECEMBER 2006 APPLICATION INFORMATION (continued) Figure 31 shows the measured input voltages and currents with different input capacitances. The voltage spike drops by about 5 V after increasing Ci from 20 µF to 40 µF. The input voltage spike has been dramatically damped by using a 47 F electrolytic capacitor. Ci = 20 mF Ci = 40 mF ( c ) C i = 4 9 mF ( 4 7 mF e l e c t r o l y t i c a n d 2 x mF ceramic) Figure 31. Adapter DC Side Hot Plug-In With Various Input Capacitances Since the input voltage to the IC is PVCC which is 0.7 V (diode voltage drop) lower than Vc during the adapter insertion, a 40-µF input capacitance is normally adequate to keep the PVCC voltage well below the maximum voltage rating under normal conditions. In case of a higher input stray inductance, the input capacitance may be increased accordingly. An electrolytic capacitor will help reduce the input voltage spike due to its high ESR. Submit Documentation Feedback 25 bq24740 www.ti.com SLUS736 – DECEMBER 2006 APPLICATION INFORMATION (continued) PCB Layout Design Guideline 1. It is critical that the exposed power pad on the backside of the IC package be soldered to the PCB ground. Ensure that there are sufficient thermal vias directly under the IC, connecting to the ground plane on the other layers. 2. The control stage and the power stage should be routed separately. At each layer, the signal ground and the power ground are connected only at the power pad. 3. The AC current-sense resistor must be connected to ACP (pin 3) and ACN (pin 2) with a Kelvin contact. The area of this loop must be minimized. The decoupling capacitors for these pins should be placed as close to the IC as possible. 4. The charge-current sense resistor must be connected to SRP (pin 19), SRN (pin 18) with a Kelvin contact. The area of this loop must be minimized. The decoupling capacitors for these pins should be placed as close to the IC as possible. 5. Decoupling capacitors for PVCC (pin 28), VREF (pin 10), REGN (pin 24) should be placed underneath the IC (on the bottom layer) with the interconnections to the IC as short as possible. 6. Decoupling capacitors for BAT (pin 17), IADAPT (pin 15) must be placed close to the corresponding IC pins with the interconnections to the IC as short as possible. 7. Decoupling capacitor CX for the charger input must be placed very close to the Q4 drain and Q5 source. Figure 32 shows the recommended component placement with trace and via locations. (a) Top Layer (b) Bottom Layer Figure 32. Layout Example 26 Submit Documentation Feedback PACKAGE MATERIALS INFORMATION www.ti.com 17-May-2007 TAPE AND REEL INFORMATION Pack Materials-Page 1 PACKAGE MATERIALS INFORMATION www.ti.com Device 17-May-2007 Package Pins Site Reel Diameter (mm) Reel Width (mm) A0 (mm) B0 (mm) K0 (mm) P1 (mm) W Pin1 (mm) Quadrant BQ24740RHDR RHD 28 MLA 330 12 5.3 5.3 1.5 8 12 PKGORN T2TR-MS P BQ24740RHDT RHD 28 MLA 180 12 5.3 5.3 1.5 8 12 PKGORN T2TR-MS P TAPE AND REEL BOX INFORMATION Device Package Pins Site Length (mm) Width (mm) BQ24740RHDR RHD 28 MLA 346.0 346.0 29.0 BQ24740RHDT RHD 28 MLA 190.0 212.7 31.75 Pack Materials-Page 2 Height (mm) PACKAGE MATERIALS INFORMATION www.ti.com 17-May-2007 Pack Materials-Page 3 IMPORTANT NOTICE Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, modifications, enhancements, improvements, and other changes to its products and services at any time and to discontinue any product or service without notice. Customers should obtain the latest relevant information before placing orders and should verify that such information is current and complete. All products are sold subject to TI’s terms and conditions of sale supplied at the time of order acknowledgment. TI warrants performance of its hardware products to the specifications applicable at the time of sale in accordance with TI’s standard warranty. Testing and other quality control techniques are used to the extent TI deems necessary to support this warranty. Except where mandated by government requirements, testing of all parameters of each product is not necessarily performed. TI assumes no liability for applications assistance or customer product design. Customers are responsible for their products and applications using TI components. To minimize the risks associated with customer products and applications, customers should provide adequate design and operating safeguards. TI does not warrant or represent that any license, either express or implied, is granted under any TI patent right, copyright, mask work right, or other TI intellectual property right relating to any combination, machine, or process in which TI products or services are used. Information published by TI regarding third-party products or services does not constitute a license from TI to use such products or services or a warranty or endorsement thereof. Use of such information may require a license from a third party under the patents or other intellectual property of the third party, or a license from TI under the patents or other intellectual property of TI. Reproduction of information in TI data books or data sheets is permissible only if reproduction is without alteration and is accompanied by all associated warranties, conditions, limitations, and notices. Reproduction of this information with alteration is an unfair and deceptive business practice. TI is not responsible or liable for such altered documentation. Resale of TI products or services with statements different from or beyond the parameters stated by TI for that product or service voids all express and any implied warranties for the associated TI product or service and is an unfair and deceptive business practice. TI is not responsible or liable for any such statements. TI products are not authorized for use in safety-critical applications (such as life support) where a failure of the TI product would reasonably be expected to cause severe personal injury or death, unless officers of the parties have executed an agreement specifically governing such use. Buyers represent that they have all necessary expertise in the safety and regulatory ramifications of their applications, and acknowledge and agree that they are solely responsible for all legal, regulatory and safety-related requirements concerning their products and any use of TI products in such safety-critical applications, notwithstanding any applications-related information or support that may be provided by TI. Further, Buyers must fully indemnify TI and its representatives against any damages arising out of the use of TI products in such safety-critical applications. TI products are neither designed nor intended for use in military/aerospace applications or environments unless the TI products are specifically designated by TI as military-grade or "enhanced plastic." Only products designated by TI as military-grade meet military specifications. Buyers acknowledge and agree that any such use of TI products which TI has not designated as military-grade is solely at the Buyer's risk, and that they are solely responsible for compliance with all legal and regulatory requirements in connection with such use. TI products are neither designed nor intended for use in automotive applications or environments unless the specific TI products are designated by TI as compliant with ISO/TS 16949 requirements. Buyers acknowledge and agree that, if they use any non-designated products in automotive applications, TI will not be responsible for any failure to meet such requirements. Following are URLs where you can obtain information on other Texas Instruments products and application solutions: Products Applications Amplifiers amplifier.ti.com Audio www.ti.com/audio Data Converters dataconverter.ti.com Automotive www.ti.com/automotive DSP dsp.ti.com Broadband www.ti.com/broadband Interface interface.ti.com Digital Control www.ti.com/digitalcontrol Logic logic.ti.com Military www.ti.com/military Power Mgmt power.ti.com Optical Networking www.ti.com/opticalnetwork Microcontrollers microcontroller.ti.com Security www.ti.com/security RFID www.ti-rfid.com Telephony www.ti.com/telephony Low Power Wireless www.ti.com/lpw Video & Imaging www.ti.com/video Wireless www.ti.com/wireless Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265 Copyright © 2007, Texas Instruments Incorporated