TI BQ24170RGYT

bq24170
bq24172
SLUSAD2B – NOVEMBER 2010 – REVISED APRIL 2011
www.ti.com
1.6-MHz Synchronous Switch-Mode Li-Ion and Li-Polymer Stand-Alone Battery Charger
with Integrated MOSFETs and Power Path Selector
Check for Samples: bq24170, bq24172
FEATURES
APPLICATIONS
•
•
•
•
•
•
•
•
1
•
•
•
•
•
•
•
•
•
1.6MHz Synchronous Switch-Mode Charger
with 4A Integrated N-MOSFETs
Up to 94% Efficiency
30V Input Rating with Adjustable Over-Voltage
Protection
– 4.5V to 17V Input Operating Voltage Range
Battery Charge Voltage
– bq24170: 1, 2, or 3-Cell with 4.2V/Cell
– bq24172: Adjustable Charge Voltage
High Integration
– Automatic Power Path Selector Between
Adapter and Battery
– Dynamic Power Management
– Integrated 20-V Switching MOSFETs
– Integrated Bootstrap Diode
– Internal Loop Compensation
– Internal Digital Soft Start
Safety
– Thermal Regulation Loop Throttles Back
Current to Limit Tj = 120°C
– Thermal Shutdown
– Battery Thermistor Sense Hot/Cold Charge
Suspend & Battery Detect
– Input Over-Voltage Protection with
Programmable Threshold
– Cycle-by-Cycle Current Limit
Accuracy
– ±0.5% Charge Voltage Regulation
– ±4% Charge Current Regulation
– ±4% Input Current Regulation
Less than 15μA Battery Current with Adapter
Removed
Less than 1.5mA Input Current with Adapter
Present and Charge Disabled
Small QFN Package
– 3.5mm × 5.5mm QFN-24 Pin
Tablet PC
Netbook and Ultra-Mobile Computers
Portable Data Capture Terminals
Portable Printers
Medical Diagnostics Equipment
Battery Bay Chargers
Battery Back-Up Systems
DESCRIPTION
The bq24170/172 is highly integrated stand-alone
Li-ion and Li-polymer switch-mode battery charger
with two integrated N-channel power MOSFETs. It
offers a constant-frequency synchronous PWM
controller with high accuracy regulation of input
current, charge current, and voltage. It closely
monitors the battery pack temperature to allow
charge only in a preset temperature window. It also
provides battery detection, pre-conditioning, charge
termination, and charge status monitoring. The
thermal regulation loop reduces charge current to
maintain the junction temperature of 120°C during
operation.
The bq24170/172 charges the battery in three
phases: precondictioning, constant current, and
constant voltage. The bq24170 charges one, two, or
three cells (selected by CELL pin), and the bq24172
is adjustable for up to three series Li+ cells.
Charge is terminated when the current reaches 10%
of the fast charge rate. A programmable charge timer
offers a safety back up. The bq24170/172
automatically restarts the charge cycle if the battery
voltage falls below an internal threshold, and enters a
low-quiescent current sleep mode when the input
voltage falls below the battery voltage.
The
bq24170/172
features
Dynamic
Power
Management (DPM) to reduce the charge current
when the input power limit is reached to avoid
over-loading the adapter. A highly-accurate
current-sense amplifier enables precise measurement
of input current from adapter to monitor overall
system power.
1
Please be aware that an important notice concerning availability, standard warranty, and use in critical applications of Texas
Instruments semiconductor products and disclaimers thereto appears at the end of this data sheet.
PRODUCTION DATA information is current as of publication date.
Products conform to specifications per the terms of the Texas
Instruments standard warranty. Production processing does not
necessarily include testing of all parameters.
Copyright © 2010–2011, Texas Instruments Incorporated
bq24170
bq24172
SLUSAD2B – NOVEMBER 2010 – REVISED APRIL 2011
www.ti.com
These devices have limited built-in ESD protection. The leads should be shorted together or the device placed in conductive foam
during storage or handling to prevent electrostatic damage to the MOS gates.
The bq24170/172 charges a battery from a DC
source as high as 17V, including a car battery. The
input over-voltage limit is adjustable through the
OVPSET pin. The AVCC, ACP, and ACN pins have a
30V rating. When a high voltage DC source is
inserted, Q1/Q2 remain off to avoid high voltage
damage to the system.
For 1 cell applications, if the battery is not removable,
the system can be directly connected to the battery to
simplify the power path design and lower the cost.
With this configuration, the battery can automatically
supplement the system load if the adapter is
overloaded.
The bq24170/172 is available in a 24-pin, 3.5mm x
5.5mm thin QFN package.
SW
1
24
2
23
3
22
4
21
5
20
6
19
AGND
7
18
8
17
9
16
10
15
14
11
12
13
ISET
PVCC
PVCC
AVCC
ACN
ACP
CMSRC
ACDRV
STAT
TS
TTC
VREF
The bq24170/172 provides power path selector gate
driver ACDRV/CMSRC on input NMOS pair ACFET
(Q1) and RBFET (Q2), and BATDRV on a battery
PMOS device (Q3). When the qualified adapter is
present, the system is directly connected to the
adapter. Otherwise, the system is connected to the
battery. In addition, the power path prevents battery
from boosting back to the input.
SW
RGY PACKAGE
(TOP VIEW)
DESCRIPTION (CONTINUED)
PGND
PGND
BTST
REGN
BATDRV
OVPSET
ACSET
SRP
SRN
CELL/FB
SPACER
SPACER
SPACER
SPACER
PIN FUNCTIONS
PIN
NO.
2
NAME
TYPE
DESCRIPTION
1,24
SW
P
Switching node, charge current output inductor connection. Connect the 0.047-µF bootstrap capacitor
from SW to BTST.
2,3
PVCC
P
Charger input voltage. Connect at least 10-µF ceramic capacitor from PVCC to PGND and place it as
close as possible to IC.
4
AVCC
P
IC power positive supply. Place a 1-µF ceramic capacitor from AVCC to AGND and place it as close as
possible to IC. Place a 10-Ω resistor from input side to AVCC pin to filter the noise. For 5V input, a 5-Ω
resistor is recommended.
5
ACN
I
Adapter current sense resistor negative input. A 0.1-µF ceramic capacitor is placed from ACN to ACP to
provide differential-mode filtering. An optional 0.1-µF ceramic capacitor is placed from ACN pin to AGND
for common-mode filtering.
6
ACP
P/I
Adapter current sense resistor positive input. A 0.1-µF ceramic capacitor is placed from ACN to ACP to
provide differential-mode filtering. A 0.1-µF ceramic capacitor is placed from ACP pin to AGND for
common-mode filtering.
7
CMSRC
O
Connect to common source of N-channel ACFET and reverse blocking MOSFET (RBFET). Place 4-kΩ
resistor from CMSRC pin to the common source of ACFET and RBFET to control the turn-on speed. The
resistance between ACDRV and CMSRC should be 500-kΩ or bigger.
8
ACDRV
O
AC adapter to system switch driver output. Connect to 4-kΩ resistor then to the gate of the ACFET
N-channel power MOSFET and the reverse conduction blocking N-channel power MOSFET. Connect
both FETs as common-source. The internal gate drive is asymmetrical, allowing a quick turn-off and
slower turn-on in addition to the internal break-before-make logic with respect to the BATDRV.
9
STAT
O
Open-drain charge status pin with 10-kΩ pull up to power rail. The STAT pin can be used to drive LED or
communicate with the host processor. It indicates various charger operations: LOW when charge in
progress. HIGH when charge is complete or in SLEEP mode. Blinking at 0.5Hz when fault occurs,
including charge suspend, input over-voltage, timer fault and battery absent.
10
TS
I
Temperature qualification voltage input. Connect a negative temperature coefficient thermistor. Program
the hot and cold temperature window with a resistor divider from VREF to TS to AGND. The temperature
qualification window can be set to 5-40°C or wider. The 103AT thermistor is recommended.
Copyright © 2010–2011, Texas Instruments Incorporated
bq24170
bq24172
SLUSAD2B – NOVEMBER 2010 – REVISED APRIL 2011
www.ti.com
PIN FUNCTIONS (continued)
PIN
NO.
NAME
TYPE
DESCRIPTION
11
TTC
I
Safety Timer and termination control. Connect a capacitor from this node to AGND to set the fast charge
safety timer(5.6min/nF). Pre-charge timer is internally fixed to 30 minutes. Pull the TTC to LOW to disable
the charge termination and safety timer. Pull the TTC to HIGH to disable the safety timer but allow the
charge termination.
12
VREF
P
3.3V reference voltage output. Place a 1-μF ceramic capacitor from VREF to AGND pin close to the IC.
This voltage could be used for programming ISET and ACSET and TS pins. It may also serve as the
pull-up rail of STAT pin and CELL pin.
13
ISET
I
Fast charge current set point. Use a voltage divider from VREF to ISET to AGND to set the fast charge
current:
ICHG =
VISET
20 ´ RSR
The pre-charge and termination current is internally as one tenth of the charge current. The charger is
disabled when ISET pin voltage is below 40mV and enabled when ISET pin voltage is above 120mV.
14
CELL
(bq24170)
I
FB
(bq24172)
Cell selection pin. Set CELL pin LOW for 1-cell, Float for 2-cell (0.8V-1.8V), and HIGH for 3-cell with a
fixed 4.2V per cell.
Charge voltage analog feedback adjustment. Connect the output of a resistor divider powered from the
battery terminals to VFB to AGND. Output voltage is regulated to 2.1V on FB pin during constant-voltage
mode.
15
SRN
I
Charge current sense resistor negative input. A 0.1-μF ceramic capacitor is placed from SRN to SRP to
provide differential-mode filtering. A 0.1-μF ceramic capacitor is placed from SRN pin to AGND for
common-mode filtering.
16
SRP
I/P
Charge current sense resistor, positive input. A 0.1-μF ceramic capacitor is placed from SRN to SRP to
provide differential-mode filtering. A 0.1-μF ceramic capacitor is placed from SRP pin to AGND for
common-mode filtering.
17
ACSET
I
Input current set point. Use a voltage divider from VREF to ACSET to AGND to set this value:
IDPM =
VACSET
20 ´ R AC
18
OVPSET
I
Valid input voltage set point. Use a voltage divider from input to OVPSET to AGND to set this voltage.
The voltage above internal 1.6V reference indicates input over-voltage, and the voltage below internal
0.5V reference indicates input under-voltage. In either condition, charge terminates, and input NMOS pair
ACFET/RBFET turn off. LED driven by STAT pin keeps blinking, reporting fault condition.
19
BATDRV
O
Battery discharge MOSFET gate driver output. Connect to 1kohm resistor to the gate of the BATFET
P-channel power MOSFET. Connect the source of the BATFET to the system load voltage node. Connect
the drain of the BATFET to the battery pack positive node. The internal gate drive is asymmetrical to
allow a quick turn-off and slower turn-on, in addition to the internal break-before-make logic with respect
to ACDRV.
20
REGN
P
PWM low side driver positive 6V supply output. Connect a 1-μF ceramic capacitor from REGN to PGND
pin, close to the IC. Generate high-side driver bootstrap voltage by integrated diode from REGN to BTST.
21
BTST
P
PWM high side driver positive supply. Connect the 0.047-µF bootstrap capacitor from SW to BTST.
22,23
PGND
P
Power ground. Ground connection for high-current power converter node. On PCB layout, connect
directly to ground connection of input and output capacitors of the charger. Only connect to AGND
through the Thermal Pad underneath the IC.
Thermal
Pad
AGND
P
Exposed pad beneath the IC. Always solder Thermal Pad to the board, and have vias on the Thermal
Pad plane star-connecting to AGND and ground plane for high-current power converter. It dissipates the
heat from the IC.
Copyright © 2010–2011, Texas Instruments Incorporated
3
bq24170
bq24172
SLUSAD2B – NOVEMBER 2010 – REVISED APRIL 2011
www.ti.com
TYPICAL APPLICATIONS
Q2
Q1
RAC: 10m
System
12V Adapter
C12: 0.1µ
RIN
2
C11: 0.1µ
C4: 10µ
CIN
2.2?
R11
4.02k
VBAT
ACN
ACP
CMSRC
R12
4.02k
D1
VREF
R2
232k
VREF
R4
100k
R1
10
BATDRV
bq24170
ISET
C1
1µ
RT
103AT
R8
5.23k
R9
30.1k
R10
1.5k
VREF
D3
VBAT
C8
0.1?
C9, C10
10? 10?
C6
1?
PGND
C3: 0.1?
VREF
C7
0.1?
REGN
AVCC
OVPSET
R7
100k
C5
0.047?
BTST
ACSET
R6
1000k
L: 3.3?H RSR:10m
SW
VREF
R3
32.4k
R5
22.1k
Q3
R14
1k
ACDRV
C2: 1µ
D2
PVCC
SRP
TTC
SRN
TS
CELL
Float
THERMAL
STAT
PAD
Figure 1. Typical Application Schematic (12V input, 2 cell battery 8.4V, 2A charge current, 0.2A
pre-charge/termination current, 3A DPM current, 18V input OVP, 0 – 45°C TS)
4
Copyright © 2010–2011, Texas Instruments Incorporated
bq24170
bq24172
SLUSAD2B – NOVEMBER 2010 – REVISED APRIL 2011
www.ti.com
Q2
Q1
C12: 0.1µ
RIN
2
C11: 0.1µ
CIN
2.2?
R11
4.02k
VBAT
ACN
ACP
CMSRC
R12
4.02k
D1
R21
100k
VREF
R4
100k
VREF
R20
599k
R21
499k
FB
LEARN
L: 2.2?H
bq24172
C5
0.047?
ISET
BTST
ACSET
C1
1µ
R6
499k
R17
49.9k
RT
103AT
TS
R9
R10
30.1k 1.5k
VREF
D3
VBAT
C8
0.1?
C9, C10
? 10?
20?
PGND
TTC
R8
5.23k
RSR:10m
C6
1?
AVCC
C3: 0.1?
VREF
C7
0.1?
REGN
OVPSET
R7
49.9k
Q3
R14
1k
SW
R22
32.4k
R5
32.4k
C4
10µ
BATDRV
VREF
R20
10
Battery LEARN
PVCC
ACDRV
C2: 1µ
D2
System
RAC: 10m
15V Adapter
THERMAL
STAT
PAD
SRP
SRN
R2
499k
FB
R1
100k
Figure 2. Typical Application Schematic with Battery Learn Function (15V input, 3 cell battery 12.6V, 4A
charge current, 0.4A pre-charge/termination current, 4A DPM current, 0 – 45°C TS)
Copyright © 2010–2011, Texas Instruments Incorporated
5
bq24170
bq24172
SLUSAD2B – NOVEMBER 2010 – REVISED APRIL 2011
RevFET
www.ti.com
Q4
RAC: 20m
Adapter
Or USB
System
0.1µ
0.1µ
PVCC
ACN
ACP
CMSRC
1µ
VREF
Selectable input
current limit
R5B
8.06k
ILIM_500mA
R11
5
R4
100k
R5A
32.4k
VREF
4.7µ
BATDRV
ACDRV
3.3?H
R2
100k
RSR: 10m
VBAT
SW
VREF
bq24170
ISET
0.047?
R3
32.4k
BTST
ACSET
REGN
0.1?
D1
Optional
0.1?
10? 10?
1?
R6
845k
C1
1µ
AVCC
PGND
OVPSET
R7
100k
RT
103AT
SRP
VREF
R8
6.81k
R9
133k
R10
1.5k
VREF
D3
TTC
SRN
TS
CELL
THERMAL
STAT
PAD
Figure 3. Typical Application Schematic wth Single Cell Unremovable Battery (USB or adapter with input
OVP 15V, up to 4A charge current, 0.4A pre-charge current, 2A adapter current or 500mA USB current,
5 – 40°C TS, system connected before sense resistor)
6
Copyright © 2010–2011, Texas Instruments Incorporated
bq24170
bq24172
SLUSAD2B – NOVEMBER 2010 – REVISED APRIL 2011
www.ti.com
USB
System
PVCC
ACN
ACP
CMSRC
1µ
VREF
Selectable
current limit
BATDRV
ACDRV
VREF
3.3?H
RSR: 20m
ISET
0.047?
BTST
R5A
12.1k
VBAT
SW
VREF
bq24172
R4
100k
R5B
12.1k
ILIM_500mA
R11
5
4.7µ
ACSET
REGN
0.1?
D1
Optional
0.1?
10?10?
1?
R6
400k
C1
1µ
AVCC
PGND
OVPSET
R7
100k
RT
103AT
SRP
VREF
TTC
R8
5.23k
STAT
VREF
D3
R2
100k
FB
TS
R10
1.5k
R9
30.1k
SRN
THERMAL
PAD
R1
100k
Figure 4. Typical Application Schematic with Single Cell Unremovable Battery (USB with input OVP 8V,
selectable charge current limit of 900mA or 500mA, 0 – 45°C TS, system connected after sense resistor)
ORDERING INFORMATION (1)
PART NUMBER
(1)
PART MARKING
PACKAGE
bq24170
bq24170
24-Pin 3.5mm×5.5mm QFN
bq24172
bq24172
24-Pin 3.5mm×5.5mm QFN
ORDERING NUMBER
QUANTITY
bq24170RGYR
3000
bq24170RGYT
250
bq24172RGYR
3000
bq24172RGYT
250
For the most current package and ordering information, see the Package Option Addendum at the end of this document, or see the TI
website at www.ti.com.
Copyright © 2010–2011, Texas Instruments Incorporated
7
bq24170
bq24172
SLUSAD2B – NOVEMBER 2010 – REVISED APRIL 2011
www.ti.com
ABSOLUTE MAXIMUM RATINGS
over operating free-air temperature range (unless otherwise noted)
(1) (2)
VALUE
Voltage range (with respect to AGND)
PVCC
–0.3 to 20
AVCC, ACP, ACN, ACDRV, CMSRC, STAT
–0.3 to 30
BTST
–0.3 to 26
BATDRV, SRP, SRN
–0.3 to 20
UNIT
–2 to 20
SW
FB (bq24172)
–0.3 to 16
OVPSET, REGN, TS, TTC, CELL (bq24170)
–0.3 to 7
V
VREF, ISET, ACSET
–0.3 to 3.6
PGND
–0.3 to 0.3
SRP–SRN, ACP-ACN
–0.5 to 0.5
V
Junction temperature range, TJ
–40 to 155
°C
Storage temperature range, Tstg
–55 to 155
°C
Maximum difference voltage
(1)
(2)
Stresses beyond those listed under absolute maximum ratings may cause permanent damage to the device. These are stress ratings
only, and functional operation of the device at these or any other conditions beyond those indicated under recommended operating
conditions is not implied. Exposure to absolute-maximum-rated conditions for extended periods may affect device reliability.
All voltages are with respect to GND if not specified. Currents are positive into, negative out of the specified terminal. Consult Packaging
Section of the data book for thermal limitations and considerations of packages.
THERMAL INFORMATION
bq24170/2
THERMAL METRIC (1)
RGY
UNITS
24 PINS
θJA
Junction-to-ambient thermal resistance (2)
ψJT
Junction-to-top characterization parameter (3)
ψJB
(1)
(2)
(3)
(4)
Junction-to-board characterization parameter
35.7
°C/W
0.4
(4)
31.2
For more information about traditional and new thermal metrics, see the IC Package Thermal Metrics application report, SPRA953.
The junction-to-ambient thermal resistance under natural convection is obtained in a simulation on a JEDEC-standard, high-K board, as
specified in JESD51-7, in an environment described in JESD51-2a.
The junction-to-top characterization parameter, ψJT, estimates the junction temperature of a device in a real system and is extracted
from the simulation data for obtaining θJA, using a procedure described in JESD51-2a (sections 6 and 7).
The junction-to-board characterization parameter, ψJB, estimates the junction temperature of a device in a real system and is extracted
from the simulation data for obtaining θJA , using a procedure described in JESD51-2a (sections 6 and 7).
RECOMMENDED OPERATING CONDITIONS
MIN
Input voltage
VIN
Output voltage
VOUT
Output current (RSR 10mΩ)
IOUT
Maximum difference voltage
4.5
UNIT
17
V
13.5
V
0.6
4
ACP - ACN
–200
200
mV
SRP–SRN
–200
200
mV
–40
85
°C
Operation free-air temperature range, TA
8
MAX
Submit Documentation Feedback
A
Copyright © 2010–2011, Texas Instruments Incorporated
Product Folder Link(s): bq24170 bq24172
bq24170
bq24172
SLUSAD2B – NOVEMBER 2010 – REVISED APRIL 2011
www.ti.com
ELECTRICAL CHARACTERISTICS
4.5V ≤ V(PVCC, AVCC) ≤ 17V, –40°C < TJ + 125°C, typical values are at TA = 25°C, with respect to AGND (unless otherwise
noted)
PARAMETER
TEST CONDITIONS
MIN
TYP
MAX
UNITS
OPERATING CONDITIONS
VAVCC_OP
AVCC input voltage operating range during
charging
4.5
17
V
QUIESCENT CURRENTS
Battery discharge current (sum of currents
into AVCC, PVCC, ACP, ACN)
IBAT
Adapter supply current (sum of current into
AVCC,ACP, ACN)
IAC
VAVCC > VUVLO, VSRN > VAVCC (SLEEP), TJ = 0°C
to 85°C
15
BTST, SW, SRP, SRN, VAVCC > VUVLO, VAVCC >
VSRN, ISET < 40mV, VBAT=12.6V, Charge
disabled
25
BTST, SW, SRP, SRN, VAVCC > VUVLO, VAVCC >
VSRN, ISET > 120mV, VBAT=12.6V, Charge done
25
VAVCC > VUVLO, VAVCC > VSRN, ISET < 40mV,
VBAT=12.6V, Charge disabled
1.2
1.5
VAVCC > VUVLO, VAVCC > VSRN, ISET > 120mV,
Charge enabled, no switching
2.5
5
VAVCC > VUVLO, VAVCC > VSRN, ISET > 120mV,
Charge enabled, switching
15 (1)
µA
mA
CHARGE VOLTAGE REGULATION
VBAT_REG
VFB_REG
SRN regulation voltage (bq24170)
Feddback regulation voltage (bq24172)
Charge voltage regulation accuracy
IFB
Leakage current into FB pin (bq24172)
CELL to AGND, 1 cell, measured on SRN
4.2
V
CELL floating, 2 cells, measured on SRN
8.4
V
CELL to VREF, 3 cells, measured on SRN
12.6
V
Measured on FB
2.1
V
TJ = 0°C to 85°C
–0.5%
0.5%
TJ = –40°C to 125°C
-0.7%
0.7%
VFB = 2.1 V
100
nA
0.8
V
CURRENT REGULATION – FAST CHARGE
VISET
ISET Voltage Range
KISET
Charge Current Set Factor (Amps of Charge
RSENSE = 10mΩ
Current per Volt on ISET pin)
RSENSE = 10mΩ
Charge Current Regulation Accuracy
(with Schottky diode on SW)
0.12
5
A/V
VSRP-SRN = 40 mV
-4%
VSRP-SRN = 20 mV
-7%
7%
VSRP-SRN = 5 mV
-25%
25%
VISET_CD
Charge Disable Threshold
ISET falling
VISET_CE
Charge Enable Threshold
ISET rising
IISET
Leakage Current into ISET
VISET = 2V
40
4%
50
100
mV
120
mV
100
nA
INPUT CURRENT REGULATION
KDPM
Input DPM Current Set Factor (Amps of
Input Current per Volt on ACSET)
Input DPM Current Regulation Accuracy
(with Schottky diode on SW)
IACSET
Leakage Current into ACSET pin
RSENSE = 10mΩ
5
A/V
VACP-ACN = 80 mV
-4%
VACP-ACN = 40 mV
-9%
4%
9%
VACP-ACN = 20 mV
–15%
15%
VACP-ACN = 5 mV
–20%
20%
VACP-ACN = 2.5 mV
-40%
40%
VACSET = 2V
100
nA
CURRENT REGULATION – PRE-CHARGE
KIPRECHG
Precharge current set factor
Precharge current regulation accuracy
(1)
(2)
10% (2)
Percentage of fast charge current
VSRP-SRN = 4 mV
–25%
25%
VSRP-SRN = 2 mV
–40%
40%
Specified by design
The minimum current is 120 mA on 10mΩ sense resistor.
Submit Documentation Feedback
Copyright © 2010–2011, Texas Instruments Incorporated
Product Folder Link(s): bq24170 bq24172
9
bq24170
bq24172
SLUSAD2B – NOVEMBER 2010 – REVISED APRIL 2011
www.ti.com
ELECTRICAL CHARACTERISTICS (continued)
4.5V ≤ V(PVCC, AVCC) ≤ 17V, –40°C < TJ + 125°C, typical values are at TA = 25°C, with respect to AGND (unless otherwise
noted)
PARAMETER
TEST CONDITIONS
MIN
TYP
MAX
UNITS
CHARGE TERMINATION
KTERM
Termination current set factor
10% (3)
Percentage of fast charge current
Termination current regulation accuracy
VSRP-SRN = 4 mV
–25%
VSRP-SRN = 2 mV
–40%
tTERM_DEG
Deglitch time for termination (both edges)
tQUAL
Termination qualification time
VSRN > VRECH and ICHG < ITERM
IQUAL
Termination qualification current
Discharge current once termination is detected
25%
40%
100
ms
250
ms
2
mA
INPUT UNDER-VOLTAGE LOCK-OUT COMPARATOR (UVLO)
VUVLO
AC under-voltage rising threshold
Measure on AVCC
VUVLO_HYS
AC under-voltage hysteresis, falling
Measure on AVCC
3.4
3.6
3.8
300
V
mV
SLEEP COMPARATOR (REVERSE DISCHARGING PROTECTION)
VSLEEP
SLEEP mode threshold
VAVCC – VSRN falling
VSLEEP_HYS
SLEEP mode hysteresis
VAVCC – VSRN rising
200
mV
tSLEEP_FALL_CD
SLEEP deglitch to disable charge
VAVCC – VSRN falling
1
ms
tSLEEP_FALL_FETOFF
SLEEP deglitch to turn off input FETs
VAVCC – VSRN falling
5
ms
tSLEEP_FALL
Deglitch to enter SLEEP mode, disable
VREF and enter low quiescent mode
VAVCC – VSRN falling
100
ms
tSLEEP_PWRUP
Deglitch to exit SLEEP mode, and enable
VREF
VAVCC – VSRN rising
30
ms
50
90
150
mV
ACN-SRN COMPARATOR
VACN-SRN
Threshold to turn on BATFET
VACN-SRN falling
VACN-SRN_HYS
Hysteresis to turn off BATFET
VACN-SRN rising
150
220
100
300
mV
mV
tBATFETOFF_DEG
Deglitch to turn on BATFET
VACN-SRN falling
2
ms
tBATFETON_DEG
Deglitch to turn off BATFET
VACN-SRN rising
50
µs
BAT LOWV COMPARATOR
VLOWV
Precharge to fast charge transition
VLOWV_HYS
Fast charge to precharge hysteresis
bq24170, CELL to AGND, 1 cell, measure on
SRN
2.87
2.9
2.93
bq24170, CELL floating, 2 cells, measure on
SRN
5.74
5.8
5.86
bq24170, CELL to VREF, 3 cells, measure on
SRN
8.61
8.7
8.79
bq24172, measure on FB
1.43
1.45
1.47
bq24170, CELL to AGND, 1 cell, measure on
SRN
200
bq24170, CELL floating, 2 cells, measure on
SRN
400
bq24170, CELL to VREF, 3 cells, measure on
SRN
600
bq24172, measure on FB
100
V
mV
tpre2fas
VLOWV rising deglitch
Delay to start fast charge current
25
ms
tfast2pre
VLOWV falling deglitch
Delay to start precharge current
25
ms
RECHARGE COMPARATOR
Recharge Threshold, below regulation
voltage limit, VBAT_REG-VSRN (bq24170), or
VFB_REG-VFB (bq24172)
VRECHG
bq24170, CELL to AGND, 1 cell, measure on
SRN
70
100
130
bq24170, CELL floating, 2 cells, measure on
SRN
140
200
260
bq24170, CELL to VREF, 3 cells, measure on
SRN
210
300
390
35
50
65
bq24172, measure on FB
mV
tRECH_RISE_DEG
VRECHG rising deglitch
VFB decreasing below VRECHG
10
ms
tRECH_FALL_DEG
VRECHG falling deglitch
VFB increasing above VRECHG
10
ms
(3)
10
The minimum current is 120 mA on 10mΩ sense resistor.
Submit Documentation Feedback
Copyright © 2010–2011, Texas Instruments Incorporated
Product Folder Link(s): bq24170 bq24172
bq24170
bq24172
SLUSAD2B – NOVEMBER 2010 – REVISED APRIL 2011
www.ti.com
ELECTRICAL CHARACTERISTICS (continued)
4.5V ≤ V(PVCC, AVCC) ≤ 17V, –40°C < TJ + 125°C, typical values are at TA = 25°C, with respect to AGND (unless otherwise
noted)
PARAMETER
TEST CONDITIONS
MIN
TYP
MAX
UNITS
1.63
V
BAT OVER-VOLTAGE COMPARATOR
VOV_RISE
Over-voltage rising threshold
As percentage of VBAT_REG (bq24170) or VFB_REG
(bq24172)
104%
VOV_FALL
Over-voltage falling threshold
As percentage of VSRN (bq24170) or VFB_REG
(bq24172)
102%
INPUT OVER-VOLTAGE COMPARATOR (ACOV)
VACOV
AC Over-Voltage Rising Threshold to turn
off ACFET
OVPSET rising
VACOV_HYS
AC over-voltage falling hysteresis
OVPSET falling
50
mV
tACOV_RISE_DEG
AC Over-Voltage Rising Deglitch to turn off
ACFET and Disable Charge
OVPSET rising
1
µs
tACOV_FALL_DEG
AC Over-Voltage Falling Deglitch to Turn on
ACFET
OVPSET falling
30
ms
1.57
1.6
INPUT UNDER-VOLTAGE COMPARATOR (ACUV)
VACUV
AC Under-Voltage Falling Threshold to turn
off ACFET
OVPSET falling
VACUV_HYS
AC Under-Voltage Rising Hysteresis
OVPSET rising
100
mV
tACOV_FALL_DEG
AC Under-Voltage Falling Deglitch to turn
off ACFET and Disable Charge
OVPSET falling
1
µs
tACOV_RISE_DEG
AC Under-Voltage Rising Deglitch to turn on
OVPSET rising
ACFET
30
ms
ISET > 120mV, Charging
120
°C
0.487
0.497
0.507
V
THERMAL REGULATION
TJ_REG
Junction Temperature Regulation Accuracy
THERMAL SHUTDOWN COMPARATOR
TSHUT
Thermal shutdown rising temperature
Temperature rising
150
°C
TSHUT_HYS
Thermal shutdown hysteresis
Temperature falling
20
°C
tSHUT_RISE_DEG
Thermal shutdown rising deglitch
Temperature rising
100
µs
tSHUT_FALL_DEG
Thermal shutdown falling deglitch
Temperature falling
10
ms
THERMISTOR COMPARATOR
VLTF
Cold Temperature Threshold, TS pin
Voltage Rising Threshold
Charger suspends charge. As percentage to
VVREF
VLTF_HYS
Cold Temperature Hysteresis, TS pin
Voltage Falling
VHTF
72.5%
73.5%
74.5%
As percentage to VVREF
0.2%
0.4%
0.6%
Hot Temperature TS pin voltage rising
Threshold
As percentage to VVREF
46.6%
47.2%
48.8%
VTCO
Cut-off Temperature TS pin voltage falling
Threshold
As percentage to VVREF
44.2%
44.7%
45.2%
tTS_CHG_SUS
Deglitch time for Temperature Out of Range
Detection
VTS > VLTF, or VTS < VTCO, or
VTS < VHTF
tTS_CHG_RESUME
Deglitch time for Temperature in Valid
Range Detection
20
ms
VTS < VLTF – VLTF_HYS or VTS >VTCO, or VTS >
VHTF
400
ms
160%
CHARGE OVER-CURRENT COMPARATOR (CYCLE-BY-CYCLE)
VOCP_CHRG
Charge Over-Current Rising Threshold,
VSRP>2.2V
Current as percentage of fast charge current
VOCP_MIN
Charge Over-Current Limit Min, VSRP<2.2V
Measure VSRP-SRN
45
mV
VOCP_MAX
Charge Over-Current Limit Max, VSRP>2.2V
Measure VSRP-SRN
75
mV
HSFET OVER-CURRENT COMPARATOR (CYCLE-BY-CYCLE)
IOCP_HSFET
Current limit on HSFET
Measure on HSFET
8
11.5
1
5
A
CHARGE UNDER-CURRENT COMPARATOR (CYCLE-BY-CYCLE)
VUCP
Charge under-current falling threshold
Measure on V(SRP-SRN)
9
Submit Documentation Feedback
Copyright © 2010–2011, Texas Instruments Incorporated
Product Folder Link(s): bq24170 bq24172
mV
11
bq24170
bq24172
SLUSAD2B – NOVEMBER 2010 – REVISED APRIL 2011
www.ti.com
ELECTRICAL CHARACTERISTICS (continued)
4.5V ≤ V(PVCC, AVCC) ≤ 17V, –40°C < TJ + 125°C, typical values are at TA = 25°C, with respect to AGND (unless otherwise
noted)
PARAMETER
TEST CONDITIONS
MIN
TYP
MAX
UNITS
BAT SHORT COMPARATOR
VBATSHT
Battery short falling threshold
Measure on SRN
2
VBATSHT_HYS
Battery short rising hysteresis
Measure on SRN
200
mV
V
tBATSHT_DEG
Deglitch on both edges
1
µs
VBATSHT
Charge Current during BATSHORT
Percentage of fast charge current
VVREF_REG
VREF regulator voltage
VAVCC > VUVLO, No load
IVREF_LIM
VREF current limit
VVREF = 0 V, VAVCC > VUVLO
35
VREGN_REG
REGN regulator voltage
VAVCC > 10 V, ISET > 120 mV
5.7
IREGN_LIM
REGN current limit
VREGN = 0 V, VAVCC > 10 v, ISET > 120 mV
40
tprechrg
Precharge Safety Timer
Precharge time before fault occurs
tfastchrg
Fast Charge Timer Range
Tchg=CTTC*KTTC
10% (4)
VREF REGULATOR
3.267
3.3
3.333
90
V
mA
REGN REGULATOR
6.0
6.3
V
120
mA
1980
Sec
TTC INPUT
1620
Fast Charge Timer Accuracy
KTTC
Timer Multiplier
VTTC_LOW
TTC Low Threshold
ITTC
TTC Source/Sink Current
VTTC_OSC_HI
TTC oscillator high threshold
VTTC_OSC_LO
TTC oscillator low threshold
1800
1
10
-10%
10%
5.6
TTC falling
45
50
hr
min/nF
0.4
V
55
µA
1.5
V
1
V
BATTERY SWITCH (BATFET) DRIVER
RDS_BAT_OFF
BATFET Turn-off Resistance
VAVCC > 5V
100
Ω
RDS_BAT_ON
BATFET Turn-on Resistance
VAVCC > 5V
20
kΩ
VBATDRV_REG
BATFET Drive Voltage
VBATDRV_REG =VACN - VBATDRV when VAVCC > 5V
and BATFET is on
7
V
tBATFET_DEG
BATFET Power-up Delay to turn off
BATFET after adapter is detected
4.2
30
ms
60
µA
6
V
AC SWITCH (ACFET) DRIVER
IACFET
ACDRV Charge Pump Current Limit
VACDRV - VCMSRC = 5V
VACDRV_REG
Gate Drive Voltage on ACFET
VACDRV - VCMSRC when VAVCC > VUVLO
RACDRV_LOAD
Maximum load between ACDRV and
CMSRC
4.2
500
kΩ
AC/BAT SWITCH DRIVER TIMING
tDRV_DEAD
Dead Time when switching between ACFET and
BATFET
Driver Dead Time
µs
10
BATTERY DETECTION
tWAKE
Wake timer
Max time charge is enabled
IWAKE
Wake current
RSENSE = 10 mΩ
tDISCHARGE
Discharge timer
Max time discharge current is applied
IDISCHARGE
IFAULT
VWAKE
Wake threshold with respect to VREG To
detect battery absent during WAKE
Measure on SRN (bq24170)
Measure on FB (bq24172)
50
mV
VDISCH
Discharge Threshold to detect battery
absent during discharge
Measure on SRN (bq24170)
2.9
V/cell
Measure on VFB (bq24172)
1.45
V
(4)
12
500
50
125
ms
200
mA
1
sec
Discharge current
8
mA
Fault current after a timeout fault
2
100
mA
mV/cell
The minimum current is 120 mA on 10mΩ sense resistor.
Submit Documentation Feedback
Copyright © 2010–2011, Texas Instruments Incorporated
Product Folder Link(s): bq24170 bq24172
bq24170
bq24172
SLUSAD2B – NOVEMBER 2010 – REVISED APRIL 2011
www.ti.com
ELECTRICAL CHARACTERISTICS (continued)
4.5V ≤ V(PVCC, AVCC) ≤ 17V, –40°C < TJ + 125°C, typical values are at TA = 25°C, with respect to AGND (unless otherwise
noted)
PARAMETER
TEST CONDITIONS
MIN
TYP
MAX
UNITS
1360
1600
1840
kHz
INTERNAL PWM
fsw
PWM Switching Frequency
(5)
tSW_DEAD
Driver Dead Time
RDS_HI
High Side MOSFET On Resistance
RDS_LO
Low Side MOSFET On Resistance
VBTST_REFRESH
Bootstrap Refresh Comparator Threshold
Voltage
Dead time when switching between LSFET and
HSFET no load
30
VBTST – VSW = 4.5 V
25
45
mΩ
60
110
mΩ
VBTST – VSW when low side refresh pulse is
requested, VAVCC=4.5V
3
VBTST – VSW when low side refresh pulse is
requested, VAVCC>6V
4
ns
V
INTERNAL SOFT START (8 steps to regulation current ICHG)
SS_STEP
Soft start steps
TSS_STEP
Soft start step time
8
1.6
step
3
ms
CHARGER SECTION POWER-UP SEQUENCING
tCE_DELAY
Delay from ISET above 120mV to start
charging battery
1.5
s
INTEGRATED BTST DIODE
VF
Forward Bias Voltage
IF=120mA at 25°C
VR
Reverse breakdown voltage
IR=2uA at 25°C
0.85
20
V
V
LOGIC IO PIN CHARACTERISTICS (STAT1, STAT2, TERM_EN)
VOUT_LO
STAT Output Low Saturation Voltage
Sink Current = 5 mA
0.5
V
VCELL_LO
CELL pin input low threshold, 1 cell
(bq24170)
CELL pin voltage falling edge
0.5
V
VCELL_MID
CELL pin input mid threshold, 2 cells
(bq24170)
CELL pin voltage rising for MIN, falling for MAX
0.8
1.8
V
VCELL_HI
CELL pin input high threshold, 3 cells
(bq24170)
CELL pin voltage rising edge
2.5
(5)
V
Specified by design
Submit Documentation Feedback
Copyright © 2010–2011, Texas Instruments Incorporated
Product Folder Link(s): bq24170 bq24172
13
bq24170
bq24172
SLUSAD2B – NOVEMBER 2010 – REVISED APRIL 2011
www.ti.com
TYPICAL CHARACTERISTICS
Table 1. Table of Graphs (1)
FIGURE
(1)
DESCRIPTION
Figure 5
AVCC, VREF, ACDRV and STAT Power Up (ISET=0)
Figure 6
Charge Enable by ISET
Figure 7
Current Soft Start
Figure 8
Charge Disable by ISET
Figure 9
Continuous Conduction Mode Switching
Figure 10
Discontinuous Conduction Mode Switching
Figure 11
BATFET to ACFET Transition during Power Up
Figure 12
System Load Transient (Input Current DPM)
Figure 13
Battery Insertion and Removal
Figure 14
Battery to Ground Short Protection
Figure 15
Battery to Ground Short Transition
Figure 16
Efficiency vs Output Current (VIN=15V)
Figure 17
Efficiency vs Output Current (VOUT=3.8V)
All waveforms and data are measured on HPA610 and HPA706 EVMs.
ISET
500mV/div
AVCC
10V/div
REGN
5V/div
VREF
2V/div
STAT
10V/div
ACDRV
5V/div
IL
1A/div
STAT
10V/div
20 ms/div
Figure 5. Power Up (ISET = 0)
400 ms/div
Figure 6. Charge Enable by ISET
ISET
500mV/div
PH
5V/div
PH
5V/div
IOUT
1A/div
IL
2A/div
4 ms/div
2 ms/div
Figure 7. Current Soft Start
14
Figure 8. Charge Disable by ISET
Submit Documentation Feedback
Copyright © 2010–2011, Texas Instruments Incorporated
Product Folder Link(s): bq24170 bq24172
bq24170
bq24172
SLUSAD2B – NOVEMBER 2010 – REVISED APRIL 2011
www.ti.com
PH
5V/div
PH
5V/div
IL
1A/div
IL
1A/div
200 ns/div
Figure 9. Continuous Conduction Mode Switching
200 ns/div
Figure 10. Discontinuous Conduction Mode Switching
AVCC
10V/div
ACDRV
10V/div
IIN
1A/div
ISYS
2A/div
VSYS
10V/div
BATDRV
10V/div
IOUT
1A/div
10 ms/div
200 ms/div
Figure 11. BATFET to ACFET Transition During Powerup
Figure 12. System Load Transient (Input current DPM)
SRN
5V/div
SRN
5V/div
PH
10V/div
PH
10V/div
IL
1A/div
IL
1A/div
400 ms/div
Figure 13. Battery Insertion and Removal
2 ms/div
Figure 14. Battery to Ground Short Protection
Submit Documentation Feedback
Copyright © 2010–2011, Texas Instruments Incorporated
Product Folder Link(s): bq24170 bq24172
15
bq24170
bq24172
SLUSAD2B – NOVEMBER 2010 – REVISED APRIL 2011
www.ti.com
SRN
5V/div
PH
10V/div
IL
1A/div
4 ms/div
Figure 15. Battery to Ground Short Transition
96
94
94
92
VIN 5V BAT 3.8V
VIN 9V BAT 3.8V
92
Efficiency - %
Efficiency - %
90
90
VIN 15V 3 cell
88
VIN 15V 2 cell
86
88
86
84
84
82
82
80
80
0
0.5
1.0
2.5
2.0
1.5
Charge Current - A
3.0
3.5
4.0
Figure 16. Efficiency vs Output Current (VIN = 15V)
16
0
0.5
1.0
2.5
2.0
1.5
Charge Current - A
3.0
3.5
4.0
Figure 17. Efficiency vs Output Current (VOUT = 3.8V)
Submit Documentation Feedback
Copyright © 2010–2011, Texas Instruments Incorporated
Product Folder Link(s): bq24170 bq24172
bq24170
bq24172
SLUSAD2B – NOVEMBER 2010 – REVISED APRIL 2011
www.ti.com
FUNCTIONAL BLOCK DIAGRAM
CMSRC+6V
SLEEP
bq24170
ACN-SRN
VACN
bq24172
UVLO
3.6V
ACOV
UVLO
AVCC
ACDRV
CHARGE PUMP
VSRN+100mV
SYSTEM
POWER
SELECTOR
CONTROL
8 ACDRV
7 CMSRC
ACN
ACUV
4
19 BATDRV
VSRN+90mV
SLEEP
ACN-6V
1.35V
LOWV
VREF 12
VREF
LDO
2.05V
RCHRG
Thermal PAD
AVCC
CE
BAT_OVP
2.184V
REGN
LDO
20 REGN
21 BTST
SRN
EAI
FBO
2 PVCC
bq24170
CELL (170)
14
FB (172)
3 PVCC
1V
2.1V
LEVEL
SHIFTER
bq24172
1 SW
IC TJ
20μA
120C
ACP
6
ACN
5
EAO
PWM
PWM
CONTROL
24 SW
REGN
20xIAC
22 PGND
20X
23 PGND
5mV
ACSET 17
CE
UCP
VSRP-VSRN
OCP
VSRP-VSRN
120mV
160%xVISET/20
ISET 13
Fast-Chrg IBAT_REG
Pre-Chrg
Selection
VSW+4.2V
REFRESH
VBTST
20μA
LOWV
EN_CHARGE
9 STAT
CE
SRP 16
20xICHG
RCHRG
Charge
Termination
20X
SRN 15
Discharge
10%xVISET
Discharge
Termination
Qualification
IDISCHARGE
IQUAL
2V
Fault
IFAULT
ACOV
BAT_SHORT
STATE
MACHINE
LTF
SUSPEND
Timer Fault
HTF
10 TS
ACOV
TCO
ACUV
1.6V
IC TJ
0.5V
VREF
VSRN
Fast Charge Timer
(TTC)
Precharge Timer
(30 mins)
TTC 11
OVPSET 18
Termination
Qualification
ACUV
TSHUT
TSHUT
SLEEP
UVLO
Figure 18. Functional Block Diagram
Submit Documentation Feedback
Copyright © 2010–2011, Texas Instruments Incorporated
Product Folder Link(s): bq24170 bq24172
17
bq24170
bq24172
SLUSAD2B – NOVEMBER 2010 – REVISED APRIL 2011
www.ti.com
DETAILED DESCRIPTION
Regulation Voltage
VRECH
I CHRG
Precharge
Current
Regulation
Phase
Fastcharge Current
Regulation Phase
Fastcharge Voltage
Regulation Phase
Termination
Charge
Current
Charge
Voltage
VLOWV
10% ICHRG
Precharge
Timer
Fast Charge Safety Timer
Figure 19. Typical Charging Profile
BATTERY VOLTAGE REGULATION
The bq24170/172 offers a high accuracy voltage regulator on for the charging voltage. The bq24170 uses CELL
pin to select number of cells with a fixed 4.2V/cell. Connecting CELL to AGND sets 1 cell output, floating CELL
pin sets 2 cell output, and connecting to VREF sets 3 cell output.
Table 2. bq24170 CELL Pin Settings
CELL PIN
VOLTAGE REGULATION
AGND
4.2V
Floating
8.4 V
VREF
12.6 V
The bq24172 uses external resistor divider for voltage feedback and regulate to internal 2.1V voltage reference
on FB pin. Use the following equation for the regulation voltage for bq24172:
é R2 ù
VBAT = 2.1 V ´ ê1+
ë R1 úû
(1)
where R2 is connected from FB to the battery and R1 is connected from FB to GND.
BATTERY CURRENT REGULATION
The ISET input sets the maximum charging current. Battery current is sensed by current sensing resistor RSR
connected between SRP and SRN. The full-scale differential voltage between SRP and SRN is 40mV max. The
equation for charge current is:
18
Submit Documentation Feedback
Copyright © 2010–2011, Texas Instruments Incorporated
Product Folder Link(s): bq24170 bq24172
bq24170
bq24172
SLUSAD2B – NOVEMBER 2010 – REVISED APRIL 2011
www.ti.com
ICHARGE =
VISET
20 ´ RSR
(2)
The valid input voltage range of ISET is up to 0.8V. With 10mΩ sense resistor, the maximum output current is
4A. With 20mΩ sense resistor, the maximum output current is 2A.
The charger is disabled when ISET pin voltage is below 40mV and is enabled when ISET pin voltage is above
120mV. For 10mΩ current sensing resistor, the minimum fast charge current must be higher than 600mA.
Under high ambient temperature, the charge current will fold back to keep IC temperature not exceeding 120°C.
BATTERY PRECHARGE CURRENT REGULATION
On Power-up, if the battery voltage is below the VLOWV threshold, the bq24170/172 applies the pre-charge
current to the battery. This pre-charge feature is intended to revive deeply discharged cells. If the VLOWV
threshold is not reached within 30 minutes of initiating pre-charge, the charger turns off and a FAULT is indicated
on the status pins.
For bq24170/172, the pre-charge current is set as 10% of the fast charge rate set by ISET voltage.
VISET
IPRECHARGE =
200 ´ RSR
(3)
INPUT CURRENT REGULATION
The total input current from an AC adapter or other DC sources is a function of the system supply current and
the battery charging current. System current normally fluctuated as portions of the systems are powered up or
down. Without Dynamic Power Management (DPM), the source must be able to supply the maximum system
current and the maximum available charger input current simultaneously. By using DPM, the input current
regulator reduces the charging current when the summation of system power and charge power exceeds the
maximum input power. Therefore, the current capability of the AC adapter can be lowered, reducing system cost.
Input current is set by the voltage on ACSET pin using the following equation:
VACSET
IDPM =
20 ´ R AC
(4)
The ACP and ACN pins are used to sense across RAC with default value of 10mΩ. However, resistors of other
values can also be used. A larger sense resistor will give a larger sense voltage and higher regulation accuracy,
at the expense of higher conduction loss.
CHARGE TERMINATION, RECHARGE, AND SAFETY TIMERS
The charger monitors the charging current during the voltage regulation phase. Termination is detected when the
SRN voltage (bq24170) or FB voltage (bq24172) is higher than recharge threshold and the charge current is less
than the termination current threshold, as calculated below:
VISET
ITERM =
200 ´ RSR
(5)
where VISET is the voltage on the ISET pin and RSR is the sense resistor. There is a 25ms deglitch time during
transition between fast-charge and pre-charge.
As a safety backup, the charger also provides an internal fixed 30 minutes pre-charge safety timer and a
programmable fast charge timer. The fast charge time is programmed by the capacitor connected between the
TTC pin and AGND, and is given by the formula:
t TTC = CTTC ´ K TTC
(6)
Where CTTC is the capacitor connected to TTC and KTTC is the constant multiplier.
A
•
•
•
new charge cycle is initiated when one of the following conditions occurs:
The battery voltage falls below the recharge threshold
A power-on-reset (POR) event occurs
ISET pin toggled below 40mV (disable charge) and above 120mV (enable charge)
Submit Documentation Feedback
Copyright © 2010–2011, Texas Instruments Incorporated
Product Folder Link(s): bq24170 bq24172
19
bq24170
bq24172
SLUSAD2B – NOVEMBER 2010 – REVISED APRIL 2011
www.ti.com
Pull TTC pin to AGND to disable both termination and fast charge safety timer (reset timer). Pull TTC pin to
VREF to disable the safety timer, but allow charge termination.
POWER UP
The charge uses a SLEEP comparator to determine the source of power on the AVCC pin, since AVCC can be
supplied either from the battery or the adapter. With the adapter source present, if the AVCC voltage is greater
than the SRN voltage, the charger exits SLEEP mode. If all conditions are met for charging, the charger then
starts charge the battery (see the Enabling and Disabling Charging section). If SRN voltage is greater than
AVCC, the charger enters low quiescent current SLEEP mode to minimize current drain from the battery. During
SLEEP mode, the VREF output turns off and the STAT pin goes to high impedance.
If AVCC is below the UVLO threshold, the device is disabled.
INPUT UNDER-VOLTAGE LOCK-OUT (UVLO)
The system must have a minimum AVCC voltage to allow proper operation. This AVCC voltage could come from
either input adapter or battery, since a conduction path exists from the battery to AVCC through the high side
NMOS body diode. When AVCC is below the UVLO threshold, all circuits on the IC are disabled.
INPUT OVER-VOLTAGE/UNDER-VOLTAGE PROTECTION
ACOV provides protection to prevent system damage due to high input voltage. In bq24170/172, once the
voltage on OVPSET is above the 1.6V ACOV threshold or below the 0.5V ACUV threshold, charge is disabled
and input MOSFETs turn off. The bq24170/172 provides flexibility to set the input qualification threshold.
ENABLE AND DISABLE CHARGING
The following conditions have to be valid before charging is enabled:
• ISET pin above 120mV
• Device is not in Under-Voltage-Lock-Out (UVLO) mode (i.e. VAVCC > VUVLO)
• Device is not in SLEEP mode (i.e. VAVCC > VSRN)
• OVPSET voltage is between 0.5V and 1.6V to qualify the adapter
• 1.5s delay is complete after initial power-up
• REGN LDO and VREF LDO voltages are at correct levels
• Thermal Shut down (TSHUT) is not valid
• TS fault is not detected
• ACFET turns on (See System Power Selector for details)
One of the following conditions stops on-going charging:
• ISET pin voltage is below 40mV
• Device is in UVLO mode
• Adapter is removed, causing the device to enter SLEEP mode
• OVPSET voltage indicates the adapter is not valid
• REGN or VREF LDO voltage is overloaded
• TSHUT temperature threshold is reached
• TS voltage goes out of range indicating the battery temperature is too hot or too cold
• ACFET turns off
• TTC timer expires or pre-charge timer expires
SYSTEM POWER SELECTOR
The IC automatically switches adapter or battery power to the system load. The battery is connected to the
system by default during power up or during SLEEP mode. When the adapter plugs in and the voltage is above
the battery voltage, the IC exits SLEEP mode. The battery is disconnected from the system and the adapter is
connected to the system after exiting SLEEP. An automatic break-before-make logic prevents shoot-through
currents when the selectors switch.
20
Submit Documentation Feedback
Copyright © 2010–2011, Texas Instruments Incorporated
Product Folder Link(s): bq24170 bq24172
bq24170
bq24172
SLUSAD2B – NOVEMBER 2010 – REVISED APRIL 2011
www.ti.com
The ACDRV is used to drive a pair of back-to-back n-channel power MOSFETs between adapter and ACP with
sources connected together to CMSRC. The n-channel FET with the drain connected to the ACP (Q2, RBFET)
provides reverse battery discharge protection, and minimizes system power dissipation with its low-RDSON. The
other n-channel FET with drain connected to adapter input (Q1, ACFET) separates battery from adapter, and
provides a limited dI/dt when connecting the adapter to the system by controlling the FET turn-on time. The
/BATDRV controls a p-channel power MOSFET (Q3, BATFET) placed between battery and system with drain
connected to battery.
Before the adapter is detected, the ACDRV is pulled to CMSRC to keep ACFET off, disconnecting the adapter
from system. /BATDRV stays at ACN-6V (clamp to ground) to connect battery to system if all the following
conditions are valid:
• VAVCC > VUVLO (battery supplies AVCC)
• VACN < VSRN + 200 mV
After the device comes out of SLEEP mode, the system begins to switch from battery to adapter. The AVCC
voltage has to be 300mV above SRN to enable the transition. The break-before-make logic keeps both ACFET
and BATFET off for 10us before ACFET turns on. This prevents shoot-through current or any large discharging
current from going into the battery. The /BATDRV is pulled up to ACN and the ACDRV pin is set to CMSRC + 6V
by an internal charge pump to turn on n-channel ACFET, connecting the adapter to the system if all the following
conditions are valid:
• VACUV < VOVPSET < VACOV
• VAVCC > VSRN + 300 mV
When the adapter is removed, the IC turns off ACFET and enters SLEEP mode.
BATFET keeps off until the system drops close to SRN. The BATDRV pin is driven to ACN - 6V by an internal
regulator to turn on p-channel BATFET, connecting the battery to the system.
Asymmetrical gate drive provides fast turn-off and slow turn-on of the ACFET and BATFET to help the
break-before-make logic and to allow a soft-start at turn–on of both MOSFETs. The delay time can be further
increased, by putting a capacitor from gate to source of the power MOSFETs.
CONVERTER OPERATION
The bq24170/172 employs a 1.6MHz constant-frequency step-down switching regulator. The fixed frequency
oscillator keeps tight control of the switching frequency under all conditions of input voltage, battery voltage,
charge current, and temperature, simplifying output filter design and keeping it out of the audible noise region.
A type III compensation network allows using ceramic capacitors at the output of the converter. An internal
saw-tooth ramp is compared to the internal error control signal to vary the duty-cycle of the converter. The ramp
height is proportional to the AVCC voltage to cancel out any loop gain variation due to a change in input voltage,
and simplifies the loop compensation. Internal gate drive logic allows achieving 97% duty-cycle before pulse
skipping starts.
AUTOMATIC INTERNAL SOFT-START CHARGER CURRENT
The charger automatically soft-starts the charger regulation current every time the charger goes into fast-charge
to ensure there is no overshoot or stress on the output capacitors or the power converter. The soft-start consists
of stepping-up the charge regulation current into 8 evenly divided steps up to the programmed charge current.
Each step lasts around 1.6ms, for a typical rise time of 12.8ms. No external components are needed for this
function.
CHARGE OVER-CURRENT PROTECTION
The charger monitors top side MOSFET current by high side sense FET. When peak current exceeds MOSFET
limit, it will turn off the top side MOSFET and keep it off until the next cycle. The charger has a secondary
cycle-to-cycle over-current protection. It monitors the charge current, and prevents the current from exceeding
160% of the programmed charge current. The high-side gate drive turns off when either over-current condition is
detected, and automatically resumes when the current falls below the over-current threshold.
Submit Documentation Feedback
Copyright © 2010–2011, Texas Instruments Incorporated
Product Folder Link(s): bq24170 bq24172
21
bq24170
bq24172
SLUSAD2B – NOVEMBER 2010 – REVISED APRIL 2011
www.ti.com
CHARGE UNDER-CURRENT PROTECTION
After the recharge, if the SRP-SRN voltage decreases below 5mV, the low side FET will be turned off for the rest
of the switching cycle. During discontinuous conduction mode (DCM), the low side FET will only turn on for a
short period of time when the boostrap capacitor voltage drops below 4V to provide refresh charge for the
capacitor. This is important to prevent negative inductor current from causing any boost effect in which the input
voltage increases as power is transferred from the battery to the input capacitors. This can lead to an
over-voltage on the AVCC node and potentially cause damage to the system.
BATTERY DETECTION
For applications with removable battery packs, IC provides a battery absent detection scheme to reliably detect
insertion or removal of battery packs. The battery detection routine runs on power up, or if battery voltage falls
below recharge threshold voltage due to removing a battery or discharging a battery.
POR or RECHARGE
Apply 8mA discharge
current, start 1s timer
VFB < VBATOWV
No
Yes
1s timer
expired
No
Yes
Battery Present,
Begin Charge
Disable 8mA
discharge current
Enable 125mA charge
current, start 0.5s timer
VFB > VRECH
Yes
Disable 125mA
charge current
No
0.5s timer
expired
No
Yes
Battery Present,
Begin Charge
Battery Absent
Figure 20. Battery Detection Flowchart
22
Submit Documentation Feedback
Copyright © 2010–2011, Texas Instruments Incorporated
Product Folder Link(s): bq24170 bq24172
bq24170
bq24172
SLUSAD2B – NOVEMBER 2010 – REVISED APRIL 2011
www.ti.com
Once the device has powered up, a 8-mA discharge current is applied to the SRN terminal. If the battery voltage
falls below the LOWV threshold within 1 second, the discharge source is turned off, and the charger is turned on
at low charge current (125mA). If the battery voltage gets up above the recharge threshold within 500ms, there is
no battery present and the cycle restarts. If either the 500ms or 1 second timer time out before the respective
thresholds are hit, a battery is detected and a charge cycle is initiated.
Battery
Absent
Battery
Absent
VBAT_RE
VRECH
Battery
Present
VLOW
Figure 21. Battery Detect Timing Diagram
Care must be taken that the total output capacitance at the battery node is not so large that the discharge current
source cannot pull the voltage below the LOWV threshold during the 1 second discharge time. The maximum
output capacitances can be calculated according to the following equations:
IDISCH ´ tDISCH
CMAX =
(for bq24170)
(4.1 V - 2.9 V) ´ Number of cells
(7)
CMAX =
IDISCH ´ tDISCH
(for bq24172)
é R2 ù
(2.05 V - 1.45 V) ´ ê1+
ú
ë R1 û
(8)
Where CMAX is the maximum output capacitance, IDISCH is the discharge current, tDISCH is the discharge time, and
R2 and R1 are the voltage feedback resistors from the battery to the FB pin.
Example
For a 3-cell Li+ charger, with R2 = 500kΩ, R1 = 100kΩ (giving 12.6V for voltage regulation), IDISCH = 8mA, tDISCH
= 1 second.
8 mA ´ 1 sec
CMAX =
= 2.2 mF
é 500 kW ù
0.6 V ´ ê1+
ú
ë 100 kW û
(9)
Based on these calculations, no more than 2200 µF should be allowed on the battery node for proper operation
of the battery detection circuit.
BATTERY SHORT PROTECTION
When SRN pin voltage is lower than 2V it is considered as battery short condition during charging period. The
charger will shut down immediately for 1ms, then soft start back to the charging current the same as precharge
current. This prevents high current may build in output inductor and cause inductor saturation when battery
terminal is shorted during charging. The converter works in non-synchronous mode during battery short.
BATTERY OVER-VOLTAGE PROTECTION
The converter will not allow the high-side FET to turn-on until the battery voltage goes below 102% of the
regulation voltage. This allows one-cycle response to an over-voltage condition – such as occurs when the load
is removed or the battery is disconnected. A total 6mA current sink from SRP/SRN to AGND allows discharging
the stored output inductor energy that is transferred to the output capacitors. If battery over-voltage condition
lasts for more than 30ms, charge is disabled.
Submit Documentation Feedback
Copyright © 2010–2011, Texas Instruments Incorporated
Product Folder Link(s): bq24170 bq24172
23
bq24170
bq24172
SLUSAD2B – NOVEMBER 2010 – REVISED APRIL 2011
www.ti.com
TEMPERATURE QUALIFICATION
The controller continuously monitors battery temperature by measuring the voltage between the TS pin and
AGND. A negative temperature coefficient thermistor (NTC) and an external voltage divider typically develop this
voltage. The controller compares this voltage against its internal thresholds to determine if charging is allowed.
To initiate a charge cycle, the battery temperature must be within the VLTF to VHTF thresholds. If battery
temperature is outside of this range, the controller suspends charge and waits until the battery temperature is
within the VLTF to VHTF range. During the charge cycle the battery temperature must be within the VLTF to VTCO
thresholds. If battery temperature is outside of this range, the controller suspends charge and waits until the
battery temperature is within the VLTF to VHTF range. The controller suspends charge by turning off the PWM
charge MOSFETss. Figure 22 summarizes the operation.
TEMPERATURE RANGE
TO INITIATE CHARGE
TEMPERATURE RANGE
DURING A CHARGE CYCLE
VREF
VREF
CHARGE SUSPENDED
CHARGE SUSPENDED
VLTF
VLTFH
VLTF
VLTFH
CHARGE at full C
CHARGE at full C
VHTF
VTCO
CHARGE SUSPENDED
CHARGE SUSPENDED
AGND
AGND
Figure 22. TS Pin, Thermistor Sense Thresholds
Assuming a 103AT NTC thermistor on the battery pack as shown in Figure 23, the values of RT1 and RT2 can
be determined by using Equation 10 and Equation 11:
æ 1
1 ö
VVREF ´ RTHCOLD ´ RTHHOT ´ ç
÷
è VLTF VTCO ø
RT2 =
æV
ö
æV
ö
RTHHOT ´ ç VREF - 1÷ - RTHCOLD ´ ç VREF - 1÷
V
V
è LTF
ø
è TCO
ø
(10)
VVREF
-1
VLTF
RT1 =
1
1
+
RT2
RTHCO LD
(11)
Select 0°C to 45°C range for Li-ion or Li-polymer battery,
RTHCOLD = 27.28 kΩ
RTHHOT = 4.911 kΩ
RT1 = 5.23 kΩ
RT2 = 30.1 kΩ
After select closest standard resistor value, by calculating the thermistor resistance at temperature threshold, the
final temperature range can be gotten from thermistor datasheet temperature-resistance table.
24
Submit Documentation Feedback
Copyright © 2010–2011, Texas Instruments Incorporated
Product Folder Link(s): bq24170 bq24172
bq24170
bq24172
SLUSAD2B – NOVEMBER 2010 – REVISED APRIL 2011
www.ti.com
VREF
bq24170
bq24172
RT1
TS
RT2
RTH
103AT
Figure 23. TS Resistor Network
MOSFET SHORT CIRCUIT AND INDUCTOR SHORT CIRCUIT PROTECTION
The IC has a short circuit protection feature. Its cycle-by-cycle current monitoring feature is achieved through
monitoring the voltage drop across Rdson of the MOSFETs. The charger will be latched off, but the ACFET keep
on to power the system. The only way to reset the charger from latch-off status is remove adapter then plug
adapter in again. Meanwhile, STAT is blinking to report the fault condition.
THERMAL REGULATION AND SHUTDOWN PROTECTION
The QFN package has low thermal impedance, which provides good thermal conduction from the silicon to the
ambient, to keep junctions temperatures low. The internal thermal regulation loop will fold back the charge
current to keep the junction temperature from exceeding 120°C. As added level of protection, the charger
converter turns off and self-protects whenever the junction temperature exceeds the TSHUT threshold of 150°C.
The charger stays off until the junction temperature falls below 130°C.
TIMER FAULT RECOVERY
The IC provides a recovery method to deal with timer fault conditions. The following summarizes this method:
Condition 1: The battery voltage is above the recharge threshold and a timeout fault occurs.
Recovery Method: The timer fault will clear when the battery voltage falls below the recharge threshold, and
battery detection will begin. A POR or taking ISET below 40mV will also clear the fault.
Condition 2: The battery voltage is below the recharge threshold and a timeout fault occurs.
Recovery Method: Under this scenario, the IC applies the fault current to the battery. This small current is used
to detect a battery removal condition and remains on as long as the battery voltage stays below the recharge
threshold. If the battery voltage goes above the recharge threshold, the IC disabled the fault current and
executes the recovery method described in Condition 1. A POR or taking ISET below 40mV will also clear the
fault.
INDUCTOR, CAPACITOR, AND SENSE RESISTOR SELECTION GUIDELINES
The IC provides internal loop compensation. With this scheme, the best stability occurs when the LC resonant
frequency, fo, is approximately 15kHz – 25kHz for the IC.
1
fo =
2p LC
(12)
Submit Documentation Feedback
Copyright © 2010–2011, Texas Instruments Incorporated
Product Folder Link(s): bq24170 bq24172
25
bq24170
bq24172
SLUSAD2B – NOVEMBER 2010 – REVISED APRIL 2011
www.ti.com
Table 3 provides a summary of typical LC components for various charge currents.
Table 3. Typical Values as a Function of Charge Current
CHARGE CURRENT
1A
2A
3A
4A
Output inductor L
6.8 µH
3.3 µH
3.3 µH
2.2 µH
Output capacitor C
10 µF
20 µF
20 µF
30 µF
CHARGE STATUS OUTPUTS
The open-drain STAT outputs indicate various charger operations as listed in Table 4. These status pins can be
used to drive LEDs or communicate with the host processor. Note that OFF indicates that the open-drain
transistor is turned off.
Table 4. STAT Pin Definition
CHARGE STATE
Charge in progress (including recharging)
ON
Charge complete, Sleep mode, Charge disabled
OFF
Charge suspend, Input over-voltage, Battery over-voltage, timer fault, , battery absent
26
STAT
Submit Documentation Feedback
BLINK
Copyright © 2010–2011, Texas Instruments Incorporated
Product Folder Link(s): bq24170 bq24172
bq24170
bq24172
SLUSAD2B – NOVEMBER 2010 – REVISED APRIL 2011
www.ti.com
APPLICATION INFORMATION
INDUCTOR SELECTION
The bq24170/72 has a 1600-kHz switching frequency to allow the use of small inductor and capacitor values.
Inductor saturation current should be higher than the charging current (ICHG) plus half the ripple current (IRIPPLE):
ISAT ³ ICHG +(1/2)IRIPPLE
(13)
Inductor ripple current depends on input voltage (VIN), duty cycle (D = VOUT/VIN), switching frequency (fs), and
inductance (L):
V ´ D ´ (1 - D)
IRIPPLE = IN
fs × L
(14)
The maximum inductor ripple current happens with D = 0.5 or close to 0.5. Usually inductor ripple is designed in
the range of 20% to 40% of the maximum charging current as a trade-off between inductor size and efficiency for
a practical design.
INPUT CAPACITOR
The input capacitor should have enough ripple current rating to absorb input switching ripple current. The worst
case RMS ripple current is half of the charging current when duty cycle is 0.5. If the converter does not operate
at 50% duty cycle, then the worst case capacitor RMS current ICIN occurs where the duty cycle is closest to 50%
and can be estimated by the following equation:
ICIN = ICHG ´ D ´ (1 - D)
(15)
A low ESR ceramic capacitor such as X7R or X5R is preferred for the input decoupling capacitor and should be
placed as close as possible to the drain of the high-side MOSFET and source of the low-side MOSFET. The
voltage rating of the capacitor must be higher than the normal input voltage level. A 25V rating or higher
capacitor is preferred for a 15V input voltage. A 20μF capacitance is suggested for a typical 3A to 4A charging
current.
OUTPUT CAPACITOR
The output capacitor also should have enough ripple current rating to absorb output switching ripple current. The
output capacitor RMS current ICOUT is given as:
I
ICOUT = RIPPLE » 0.29 ´ IRIPPLE
2 ´ 3
(16)
The output capacitor voltage ripple can be calculated as follows:
DVO =
VOUT æ
V
ç 1 - OUT
2 ç
VIN
8LCfs è
ö
÷
÷
ø
(17)
At certain input/output voltages and switching frequencies, the voltage ripple can be reduced by increasing the
output filter LC.
The bq24170/72 has an internal loop compensator. To achieve good loop stability, the resonant frequency of the
output inductor and output capacitor should be designed between 15 kHz and 25 kHz. The preferred ceramic
capacitor has a 25V or higher rating, X7R or X5R.
INPUT FILTER DESIGN
During adapter hot plug-in, the parasitic inductance and the input capacitor from the adapter cable form a second
order system. The voltage spike at the AVCC pin may be beyond the IC maximum voltage rating and damage
the IC. The input filter must be carefully designed and tested to prevent an over-voltage event on the AVCC pin.
There are several methods to damping or limiting the over-voltage spike during adapter hot plug-in. An
electrolytic capacitor with high ESR as an input capacitor can damp the over-voltage spike well below the IC
maximum pin voltage rating. A high current capability TVS Zener diode can also limit the over-voltage level to an
IC safe level. However, these two solutions may not be lowest cost or smallest size.
Submit Documentation Feedback
Copyright © 2010–2011, Texas Instruments Incorporated
Product Folder Link(s): bq24170 bq24172
27
bq24170
bq24172
SLUSAD2B – NOVEMBER 2010 – REVISED APRIL 2011
www.ti.com
A cost effective and small size solution is shown in Figure 24. R1 and C1 are composed of a damping RC
network to damp the hot plug-in oscillation. As a result, the over-voltage spike is limited to a safe level. D1 is
used for reverse voltage protection for the AVCC pin. C2 is the AVCC pin decoupling capacitor and it should be
placed as close as possible to the AVCC pin. R2 and C2 form a damping RC network to further protect the IC
from high dv/dt and high voltage spike. The C2 value should be less than the C1 value so R1 can dominant the
equivalent ESR value to get enough damping effect for hot plug-in. R1 and R2 must be sized enough to handle
in-rush current power loss according to the resistor manufacturer’s datasheet. The filter component values
always need to be verified with a real application and minor adjustments may be needed to fit in the real
application circuit.
If the input is 5V (USB host or USB adapter), the D1 can be saved. R2 has to be 5Ω or higher to limit the current
if the input reversely inserted.
D1
R2(1206)
4.7 - 30 W
R1(2010)
2W
Adapter
Connector
AVCC pin
C1
2.2 mF
C2
0.1 - 1 mF
Figure 24. Input Filter
INPUT ACFET AND RBFET SELECTION
N-type MOSFETs are used as input ACFET(Q1) and RBFET(Q2) for better cost effective and small size solution,
as shown in Figure 22. Normally, there are around 50uF capacitor totally connected at PVCC node --- 10uF
capacitor for buck converter of bq24170/2 and 40uF capacitor for system side. There is a surge current during
Q1 turn-on period when a valid adapter is inserted. Decreasing the turn-on speed of Q1 can limit this surge
current in desirable range by selecting a MOSFET with relative bigger CGD and/or CGS. At the case Q1 turn on
too fast, we need add external CGD and/or CGS. For example, 4.7nF CGD and 47nF CGS are adopted on EVM
while using NexFET CSD17313 as Q1.
RIN
2
CIN
2. ?
2.2?
Q2
Q1
ADAPTER
SYS
RSNS
C4 1m
RGS
499k
CGS
CGD
R11
4.02k
R12
4.02k
CSYS
40?
PVCC
CMSRC
ACDRV
Figure 25. Input ACFET and RBFET
PCB LAYOUT
The switching node rise and fall times should be minimized for minimum switching loss. Proper layout of the
components to minimize the high frequency current path loop (see Figure 26) is important to prevent electrical
and magnetic field radiation and high frequency resonant problems. The following is a PCB layout priority list for
proper layout. Layout of the PCB according to this specific order is essential.
1. Place input capacitor as close as possible to the PVCC supply and ground connections and use the shortest
copper trace connection. These parts should be placed on the same layer of the PCB instead of on different
layers and using vias to make this connection.
2. Place the inductor input terminal as close as possible to the SW terminal. Minimize the copper area of this
trace to lower electrical and magnetic field radiation but make the trace wide enough to carry the charging
current. Do not use multiple layers in parallel for this connection. Minimize parasitic capacitance from this
28
Submit Documentation Feedback
Copyright © 2010–2011, Texas Instruments Incorporated
Product Folder Link(s): bq24170 bq24172
bq24170
bq24172
SLUSAD2B – NOVEMBER 2010 – REVISED APRIL 2011
www.ti.com
3.
4.
5.
6.
7.
8.
9.
area to any other trace or plane.
The charging current sensing resistor should be placed right next to the inductor output. Route the sense
leads connected across the sensing resistor back to the IC in the same layer, close to each other (minimize
loop area) and do not route the sense leads through a high-current path (see Figure 27 for Kelvin connection
for best current accuracy). Place decoupling capacitor on these traces next to the IC.
Place output capacitor next to the sensing resistor output and ground.
Output capacitor ground connections need to be tied to the same copper that connects to the input capacitor
ground before connecting to system ground.
Route analog ground separately from power ground and use a single ground connection to tie charger power
ground to charger analog ground. Just beneath the IC use analog ground copper pour but avoid power pins
to reduce inductive and capacitive noise coupling. Use the thermal pad as a single ground connection point
to connect analog ground and power ground together, or use a 0-Ω resistor to tie analog ground to power
ground. A star-connection under the thermal pad is highly recommended.
It is critical that the exposed thermal pad on the backside of the IC package be soldered to the PCB ground.
Ensure that there are sufficient thermal vias directly under the IC, connecting to the ground plane on the
other layers.
Decoupling capacitors should be placed next to the IC pins and make trace connection as short as possible.
The number and physical size of the vias should be enough for a given current path.
SW
L1
R1
High
Frequency
VIN
Current
Path
C1
VBAT
BAT
PGND
C3
C2
Figure 26. High Frequency Current Path
Current Direction
R SNS
Current Sensing Direction
To SRP and SRN pin
Figure 27. Sensing Resistor PCB Layout
Submit Documentation Feedback
Copyright © 2010–2011, Texas Instruments Incorporated
Product Folder Link(s): bq24170 bq24172
29
bq24170
bq24172
SLUSAD2B – NOVEMBER 2010 – REVISED APRIL 2011
www.ti.com
REVISION HISTORY
Changes from Original (November 2010) to Revision A
•
Page
Changed status from product preview to production data .................................................................................................... 1
Changes from Revision A (November 2010) to Revision B
Page
•
Changed FEATURES third bullet to 30V Input Rating with Adjustable Over-Voltage Protection and added sub-bullet:
4.5V to 17V Input Operating Voltage Range ........................................................................................................................ 1
•
Added a new paragraph in DESCRIPTION on page 2, second paragraph ......................................................................... 2
•
Deleted last sentence in Pin NO. 19, Description column .................................................................................................... 3
•
Added diode between BTST and REGN pins in Figure 3 .................................................................................................... 6
•
Added diode between BTST and REGN pins in Figure 4 .................................................................................................... 7
•
Added 2nd row in the ABS MAX TABLE, moving AVCC,....STAT from first row to second row and adding -0.3 to 30
in Value column. Also moved ACDRV to this row from next row ......................................................................................... 8
•
Changed RECOMMENDED OPERATING CONDITIONS Output current row, MIN column from 600 to 0.6 ...................... 8
•
Changed MIN and MAX columns from 1.55 to 1.57, and 1.65 to 1.63 in first row under INPUT OVER-VOLTAGE
COMPARATOR (ACOV) section in ELECTRICAL CHARACTERISTICS table ................................................................. 11
•
Changed MIN, TYP, MAX column from 0.45 to 0.487, 0.5 to 0.497 and 0.55 to 0.507 in first row under INPUT
UNDER-VOLTAGE COMPARATOR (ACUV) section in ELECTRICAL CHARACTERISTICS table ................................. 11
•
Added paragraph to INPUT FILTER DESIGN section ....................................................................................................... 28
30
Submit Documentation Feedback
Copyright © 2010–2011, Texas Instruments Incorporated
Product Folder Link(s): bq24170 bq24172
PACKAGE OPTION ADDENDUM
www.ti.com
11-Apr-2013
PACKAGING INFORMATION
Orderable Device
Status
(1)
Package Type Package Pins Package
Drawing
Qty
Eco Plan
Lead/Ball Finish
(2)
MSL Peak Temp
Op Temp (°C)
Top-Side Markings
(3)
(4)
BQ24170RGYR
ACTIVE
VQFN
RGY
24
3000
Green (RoHS
& no Sb/Br)
CU NIPDAU
Level-2-260C-1 YEAR
-40 to 85
BQ24170
BQ24170RGYT
ACTIVE
VQFN
RGY
24
250
Green (RoHS
& no Sb/Br)
CU NIPDAU
Level-2-260C-1 YEAR
-40 to 85
BQ24170
BQ24172RGYR
ACTIVE
VQFN
RGY
24
3000
Green (RoHS
& no Sb/Br)
CU NIPDAU
Level-2-260C-1 YEAR
-40 to 85
BQ24172
BQ24172RGYT
ACTIVE
VQFN
RGY
24
250
Green (RoHS
& no Sb/Br)
CU NIPDAU
Level-2-260C-1 YEAR
-40 to 85
BQ24172
(1)
The marketing status values are defined as follows:
ACTIVE: Product device recommended for new designs.
LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect.
NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in a new design.
PREVIEW: Device has been announced but is not in production. Samples may or may not be available.
OBSOLETE: TI has discontinued the production of the device.
(2)
Eco Plan - The planned eco-friendly classification: Pb-Free (RoHS), Pb-Free (RoHS Exempt), or Green (RoHS & no Sb/Br) - please check http://www.ti.com/productcontent for the latest availability
information and additional product content details.
TBD: The Pb-Free/Green conversion plan has not been defined.
Pb-Free (RoHS): TI's terms "Lead-Free" or "Pb-Free" mean semiconductor products that are compatible with the current RoHS requirements for all 6 substances, including the requirement that
lead not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered at high temperatures, TI Pb-Free products are suitable for use in specified lead-free processes.
Pb-Free (RoHS Exempt): This component has a RoHS exemption for either 1) lead-based flip-chip solder bumps used between the die and package, or 2) lead-based die adhesive used between
the die and leadframe. The component is otherwise considered Pb-Free (RoHS compatible) as defined above.
Green (RoHS & no Sb/Br): TI defines "Green" to mean Pb-Free (RoHS compatible), and free of Bromine (Br) and Antimony (Sb) based flame retardants (Br or Sb do not exceed 0.1% by weight
in homogeneous material)
(3)
MSL, Peak Temp. -- The Moisture Sensitivity Level rating according to the JEDEC industry standard classifications, and peak solder temperature.
(4)
Multiple Top-Side Markings will be inside parentheses. Only one Top-Side Marking contained in parentheses and separated by a "~" will appear on a device. If a line is indented then it is a
continuation of the previous line and the two combined represent the entire Top-Side Marking for that device.
Important Information and Disclaimer:The information provided on this page represents TI's knowledge and belief as of the date that it is provided. TI bases its knowledge and belief on information
provided by third parties, and makes no representation or warranty as to the accuracy of such information. Efforts are underway to better integrate information from third parties. TI has taken and
continues to take reasonable steps to provide representative and accurate information but may not have conducted destructive testing or chemical analysis on incoming materials and chemicals.
TI and TI suppliers consider certain information to be proprietary, and thus CAS numbers and other limited information may not be available for release.
In no event shall TI's liability arising out of such information exceed the total purchase price of the TI part(s) at issue in this document sold by TI to Customer on an annual basis.
Addendum-Page 1
Samples
PACKAGE OPTION ADDENDUM
www.ti.com
11-Apr-2013
Addendum-Page 2
PACKAGE MATERIALS INFORMATION
www.ti.com
26-Jan-2013
TAPE AND REEL INFORMATION
*All dimensions are nominal
Device
Package Package Pins
Type Drawing
BQ24170RGYR
VQFN
RGY
24
SPQ
Reel
Reel
A0
Diameter Width (mm)
(mm) W1 (mm)
B0
(mm)
K0
(mm)
P1
(mm)
W
Pin1
(mm) Quadrant
3000
330.0
12.4
3.8
5.8
1.2
8.0
12.0
Q1
BQ24170RGYT
VQFN
RGY
24
250
180.0
12.4
3.8
5.8
1.2
8.0
12.0
Q1
BQ24172RGYR
VQFN
RGY
24
3000
330.0
12.4
3.8
5.8
1.2
8.0
12.0
Q1
BQ24172RGYT
VQFN
RGY
24
250
180.0
12.4
3.8
5.8
1.2
8.0
12.0
Q1
Pack Materials-Page 1
PACKAGE MATERIALS INFORMATION
www.ti.com
26-Jan-2013
*All dimensions are nominal
Device
Package Type
Package Drawing
Pins
SPQ
Length (mm)
Width (mm)
Height (mm)
BQ24170RGYR
VQFN
RGY
24
3000
367.0
367.0
35.0
BQ24170RGYT
VQFN
RGY
24
250
210.0
185.0
35.0
BQ24172RGYR
VQFN
RGY
24
3000
367.0
367.0
35.0
BQ24172RGYT
VQFN
RGY
24
250
210.0
185.0
35.0
Pack Materials-Page 2
IMPORTANT NOTICE
Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, enhancements, improvements and other
changes to its semiconductor products and services per JESD46, latest issue, and to discontinue any product or service per JESD48, latest
issue. Buyers should obtain the latest relevant information before placing orders and should verify that such information is current and
complete. All semiconductor products (also referred to herein as “components”) are sold subject to TI’s terms and conditions of sale
supplied at the time of order acknowledgment.
TI warrants performance of its components to the specifications applicable at the time of sale, in accordance with the warranty in TI’s terms
and conditions of sale of semiconductor products. Testing and other quality control techniques are used to the extent TI deems necessary
to support this warranty. Except where mandated by applicable law, testing of all parameters of each component is not necessarily
performed.
TI assumes no liability for applications assistance or the design of Buyers’ products. Buyers are responsible for their products and
applications using TI components. To minimize the risks associated with Buyers’ products and applications, Buyers should provide
adequate design and operating safeguards.
TI does not warrant or represent that any license, either express or implied, is granted under any patent right, copyright, mask work right, or
other intellectual property right relating to any combination, machine, or process in which TI components or services are used. Information
published by TI regarding third-party products or services does not constitute a license to use such products or services or a warranty or
endorsement thereof. Use of such information may require a license from a third party under the patents or other intellectual property of the
third party, or a license from TI under the patents or other intellectual property of TI.
Reproduction of significant portions of TI information in TI data books or data sheets is permissible only if reproduction is without alteration
and is accompanied by all associated warranties, conditions, limitations, and notices. TI is not responsible or liable for such altered
documentation. Information of third parties may be subject to additional restrictions.
Resale of TI components or services with statements different from or beyond the parameters stated by TI for that component or service
voids all express and any implied warranties for the associated TI component or service and is an unfair and deceptive business practice.
TI is not responsible or liable for any such statements.
Buyer acknowledges and agrees that it is solely responsible for compliance with all legal, regulatory and safety-related requirements
concerning its products, and any use of TI components in its applications, notwithstanding any applications-related information or support
that may be provided by TI. Buyer represents and agrees that it has all the necessary expertise to create and implement safeguards which
anticipate dangerous consequences of failures, monitor failures and their consequences, lessen the likelihood of failures that might cause
harm and take appropriate remedial actions. Buyer will fully indemnify TI and its representatives against any damages arising out of the use
of any TI components in safety-critical applications.
In some cases, TI components may be promoted specifically to facilitate safety-related applications. With such components, TI’s goal is to
help enable customers to design and create their own end-product solutions that meet applicable functional safety standards and
requirements. Nonetheless, such components are subject to these terms.
No TI components are authorized for use in FDA Class III (or similar life-critical medical equipment) unless authorized officers of the parties
have executed a special agreement specifically governing such use.
Only those TI components which TI has specifically designated as military grade or “enhanced plastic” are designed and intended for use in
military/aerospace applications or environments. Buyer acknowledges and agrees that any military or aerospace use of TI components
which have not been so designated is solely at the Buyer's risk, and that Buyer is solely responsible for compliance with all legal and
regulatory requirements in connection with such use.
TI has specifically designated certain components as meeting ISO/TS16949 requirements, mainly for automotive use. In any case of use of
non-designated products, TI will not be responsible for any failure to meet ISO/TS16949.
Products
Applications
Audio
www.ti.com/audio
Automotive and Transportation
www.ti.com/automotive
Amplifiers
amplifier.ti.com
Communications and Telecom
www.ti.com/communications
Data Converters
dataconverter.ti.com
Computers and Peripherals
www.ti.com/computers
DLP® Products
www.dlp.com
Consumer Electronics
www.ti.com/consumer-apps
DSP
dsp.ti.com
Energy and Lighting
www.ti.com/energy
Clocks and Timers
www.ti.com/clocks
Industrial
www.ti.com/industrial
Interface
interface.ti.com
Medical
www.ti.com/medical
Logic
logic.ti.com
Security
www.ti.com/security
Power Mgmt
power.ti.com
Space, Avionics and Defense
www.ti.com/space-avionics-defense
Microcontrollers
microcontroller.ti.com
Video and Imaging
www.ti.com/video
RFID
www.ti-rfid.com
OMAP Applications Processors
www.ti.com/omap
TI E2E Community
e2e.ti.com
Wireless Connectivity
www.ti.com/wirelessconnectivity
Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265
Copyright © 2013, Texas Instruments Incorporated