application INFO available UC2855A/B UC3855A/B High Performance Power Factor Preregulator FEATURES DESCRIPTION • Controls Boost PWM to Near Unity Power Factor The UC3855A/B provides all the control features necessary for high power, high frequency PFC boost converters. The average current mode control method allows for stable, low distortion AC line current programming without the need for slope compensation. In addition, the UC3855 utilizes an active snubbing or ZVT (Zero Voltage Transition technique) to dramatically reduce diode recovery and MOSFET turn-on losses, resulting in lower EMI emissions and higher efficiency. Boost converter switching frequencies up to 500kHz are now realizable, requiring only an additional small MOSFET, diode, and inductor to resonantly soft switch the boost diode and switch. Average current sensing can be employed using a simple resistive shunt or a current sense transformer. Using the current sense transformer method, the internal current synthesizer circuit buffers the inductor current during the switch on-time, and reconstructs the inductor current during the switch off-time. Improved signal to noise ratio and negligible current sensing losses make this an attractive solution for higher power applications. • Fixed Frequency Average Current Mode Control Minimizes Line Current Distortion • Built-in Active Snubber (ZVT) allows Operation to 500kHz, improved EMI and Efficiency • Inductor Current Synthesizer allows Single Current Transformer Current Sense for Improved Efficiency and Noise Margin • Accurate Analog Multiplier with Line Compensator allows for Universal Input Voltage Operation • High Bandwidth (5MHz), Low Offset Current Amplifier • Overvoltage and Overcurrent protection • Two UVLO Threshold Options • 150µA Startup Supply Current Typical • Precision 1% 7.5V Reference The UC3855A/B also features a single quadrant multiplier, squarer, and divider circuit which provides the programming signal for the current loop. The internal multiplier current limit reduces output power during low line conditions. An overvoltage protection circuit disables both controller outputs in the event of a boost output OV condition. Low startup supply current, UVLO with hysteresis, a 1% 7.5V reference, voltage amplifier with softstart, input supply voltage clamp, enable comparator, and overcurrent comparator complete the list of features. Available packages include: 20 pin N, DW, Q, J, and L. BLOCK DIAGRAM License Patent from Pioneer Magnetics. Pin numbers refer to DIL-20 J or N packages. SLUS328A JUNE 1998 - REVISED MAY 2004 UDG-94001-2 UC2855A/B UC3855A/B CONNECTION DIAGRAMS ABSOLUTE MAXIMUM RATINGS Supply Voltage VCC. . . . . . . . . . . . . . . . . . . . . . . . . . Internally Limited VCC Supply Clamp Current . . . . . . . . . . . . . . . . . . . . . . . 20mA PFC Gate Driver Current (continuous) . . . . . . . . . . . . . . ± 0.5A PFC Gate Driver Current (peak) . . . . . . . . . . . . . . . . . . . ± 1.5A ZVT Drive Current (continuous) . . . . . . . . . . . . . . . . . . . ± 0.25A ZVT Drive Current (peak). . . . . . . . . . . . . . . . . . . . . . . . ± 0.75A Input Current (IAC, RT, RVA) . . . . . . . . . . . . . . . . . . . . . . . 5mA Analog Inputs (except Peak Limit) . . . . . . . . . . . . . . −0.3 to 10V Peak Limit Input . . . . . . . . . . . . . . . . . . . . . . . . . . . −0.3 to 6.5V Softstart Sinking Current . . . . . . . . . . . . . . . . . . . . . . . . . 1.5mA Storage Temperature . . . . . . . . . . . . . . . . . . . −65°C to +150°C Junction Temperature . . . . . . . . . . . . . . . . . . . −55°C to +150°C Lead Temperature (Soldering, 10 sec.) . . . . . . . . . . . . . +300°C PLCC-20 & LCC-20 (Top View) Q or L Package Currents are positive into, negative out of the specified terminal. Consult Packaging Section of Databook for thermal limitations and considerations of packages. All voltages are referenced to GND. DIL–20 (Top View) J or N Package SOIC-20 (Top View) DW Package ELECTRICAL CHARACTERISTICS:Unless otherwise specified: VCC = 18V, RT = 15k, RVS = 23k, CT = 470pF, CI = 150pF, VRMS = 1.5V, IAC = 100µA, ISENSE = 0V, CAOUT = 4V, VAOUT= 3.5V, VSENSE = 3V. –40°C to 85°C (UC2855A/B), 0°C to 70°C (UC3855A/B). PARAMETER TEST CONDITIONS MIN TYP MAX UNITS CAO, VAOUT = 0V, VCC = UVLO −0.3V 150 500 µA 17 25 mA VCC Turn-On Threshold UC3855A 15.5 17.5 VCCTurn-Off Threshold UC3855A,B Overall Supply Current, OFF Supply Current, OPERATING 9 VCC Turn-On Threshold UC3855B VCC Clamp I(VCC) = ICC(on) + 5mA 10 V V 10.5 10.8 V 20 22 V 3.1 V −500 25 500 nA 18 Voltage Amplifier Input Voltage 2.9 VSENSE Bias Current Open Loop Gain VOUT = 2 to 5V 65 80 VOUT High ILOAD = –300µA 5.75 6 6.25 VOUT Low ILOAD = 300µA 0.3 0.5 V Output Short Circuit Current VOUT = 0V 0.6 3 mA 2 dB V UC2855A/B UC3855A/B ELECTRICAL CHARACTERISTICS:Unless otherwise specified: VCC = 18V, RT = 15k, RVS = 23k, CT = 470pF, CI = 150pF, VRMS = 1.5V, IAC = 100µA, ISENSE = 0V, CAOUT = 4V, VAOUT= 3.5V, VSENSE = 3V. –40°C to 85°C (UC2855A/B), 0°C to 70°C (UC3855A/B). PARAMETER TEST CONDITIONS MIN TYP MAX UNITS Current Amplifier −4 4 mV Input Offset Voltage VCM = − 2.5V −500 500 nA Input Bias Current (Sense) VCM = 2.5V 80 110 dB Open Loop Gain VCM = 2.5V, VOUT = 2 to 6V ILOAD = −500µA 6 V VOUT High ILOAD = 500µA 0.3 0.5 V VOUT Low 1 3 mA Output Short Circuit Current VOUT = 0V Common Mode Range −0.3 5 V 2.5 5 MHz Gain Bandwidth Product FIN = 100kHz, 10mV, P–P, TA = 25°C Reference 7.388 7.5 7.613 V Output Voltage IREF = 0mA, TA = 25°C 7.313 7.5 7.688 V IREF = 0mA −15 15 mV Load Regulation IREF = 1 to 10 mA Line Regulation VCC = 15 to 35V −10 10 mV Short Circuit Current REF = 0V 20 45 65 mA Oscillator 170 200 230 kHz Initial Accuracy TA = 25°C 1 % Voltage Stability VCC = 12 to 18V Total Variation Line, Temp. 160 240 kHz Ramp Amplitude (P–P) Outputs at 0% duty cycle 4.7 5.7 V Ramp Valley Voltage 1.1 1.6 V Enable/OVP/Current Limit Enable Threshold 1.8 2.2 V OVP Threshold 7.5 7.66 V OVP Hysteresis 200 400 600 mV OVP Propagation Delay 200 ns OVP Input Bias Current V= 7.5V 1 10 µA 1.25 1.5 1.75 V PKLIMIT Threshold VPKLIMIT = 1.5V 100 µA PKLIMIT Input Current 100 ns PKLIMIT Prop. Delay Multiplier Output Current - IAC Limited IAC = 100µA, VRMS = 1V −235 −205 −175 µA Output Current - Zero IAC = 0µA −2 −0.2 2 µA Output Current - Power Limited VRMS = 1.5V, VAOUT = 5.5V −250 −209 −160 µA Output Current VRMS = 1.5V, VAOUT = 2V −26 µA VRMS = 1.5V VAOUT = 5V −190 µA VRMS = 5V, VAOUT = 2V −3 µA VRMS = 5V, VAOUT = 5V −17 µA Gain Constant Refer to Note 1 −0.95 −0.85 −0.75 1/V Gate Driver Output 12 12.8 V Output High Voltage lOUT = −200mA, VCC = 15V 1 2.2 V Output Low Voltage lOUT = 200mA 300 500 mV Output Low Voltage lOUT = 10mA Output Low (UVLO) lOUT = 50mA, VCC = 0V 0.9 1.5 V Output RISE/FALL Time CLOAD = 1nF 35 ns Output Peak Current CLOAD = 10nF 1.5 A 3 UC2855A/B UC3855A/B ELECTRICAL CHARACTERISTICS:Unless otherwise specified: VCC = 18V, RT = 15k, RVS = 23k, CT = 470pF, CI = 150pF, VRMS = 1.5V, IAC = 100µA, ISENSE = 0V, CAOUT = 4V, VAOUT= 3.5V, VSENSE = 3V. –40°C to 85°C (UC2855A/B), 0°C to 70°C (UC3855A/B). PARAMETER TEST CONDITIONS MIN TYP MAX UNITS ZVT Reset Threshold 2.3 2.6 2.9 V Input Bias Current V = 2.5V, VCT = 0 6 20 µA Propagation Delay Measured at ZVTOUT 100 ns Maximum Pulse Width 400 ns Output High Voltage lOUT = −100mA, VCC = 15V 12 12.8 V Output Low Voltage lOUT = 100mA 1 2.2 V lOUT = 10mA 300 900 mV Output Low (UVLO) lOUT = 50mA, VCC = 0V 0.9 1.5 V Output RISE/FALL Time CLOAD = 1nF 35 ns Output Peak Current CLOAD = 10nF 0.75 A Current Synthesizer ION to CS Offset VION = 0V 30 50 mV Cl Discharge Current IAC = 50µA 105 118 140 µA IAC = 500µA 5 µA IAC Offset Voltage 0.3 0.65 1.1 V ION Buffer Slew Rate 10 V/µs ION Input Bias Current VION = 2V 2 15 µA RVS Output Voltage 23k from RVS to GND 2.87 3 3.13 V Note 1: Gain constant (K) = IAC • (VAOUT – 1. 5V ) (VR MS 2 • IMO ) at VRMS = 1.5V, VAOUT = 5.5V. PIN DESCRIPTIONS CS: The reconstructed inductor current waveform generated on the CI pin is level shifted down a diode drop to this pin. Connect the current amplifier input resistor between CS and the inverting input of the current amplifier. The waveform on this pin is compared to the multiplier output waveform through the average current sensing current amplifier. The input to the peak current limiting comparator is also connected to this pin. A voltage level greater than 1.5 volts on this pin will trip the comparator and disable the gate driver output. CA This is the inverting input to the current amplifier. Connect the required compensation components between this pin and CAOUT. The common mode operating range for this input is between −0.3V and 5V. CAO: This is the output of the wide bandwidth current amplifier and one of the inputs to the PWM duty cycle comparator. The output signal generated by this amplifier commands the PWM to force the correct input current. The output can swing from 0.1V to 7.5V. CT: A capacitor from CT to GND sets the PWM oscillator frequency according to the following equation: CI: The level shifted current sense signal is impressed upon a capacitor connected between this pin and GND. The buffered current sense transformer signal charges the capacitor when the boost switch is on. When the switch is off, the current synthesizer discharges the capacitor at a rate proportional to the dI/dt of the boost inductor current. In this way, the discharge current is approximately equal to f≈ Use a high quality ceramic capacitor with low ESL and ESR for best results. A minimum CT value of 200pF insures good accuracy and less susceptibility to circuit layout parasitics. The oscillator and PWM are designed to provide practical operation to 500kHz. 3V IAC . – R R VS 4 Discharging the CI capacitor in this fashion, a “reconstructed” version of the inductor current is generated using only one current sense transformer. 1 . 11200 • CT 4 GND: All voltages are measured with respect to this pin. All bypass and timing capacitors connected to GND should have leads as short and direct as possible. UC2855A/B UC3855A/B PIN DESCRIPTIONS (cont.) GTOUT: The output of the PWM is a 1.5A peak totem pole MOSFET gate driver on GTOUT. A series resistor between GTOUT and the MOSFET gate of at least 10 ohms should be used to limit the overshoot on GTOUT. In addition, a low VF Schottky diode should be connected between GTOUT and GND to limit undershoot and possible erratic operation. REF: REF is the output of the precision reference. The output is capable of supplying 25mA to peripheral circuitry and is internally short circuit current limited. REF is disabled and low whenever VCC is below the UVLO threshold, and when OVP is below 1.8V. A REF “GOOD” comparator senses REF and disables the stage until REF has attained approximately 90% of its nominal value. Bypass REF to GND with a 0.1µF or larger ceramic capacitor for best stability. IAC: This is a current input to the multiplier. The current into this pin should correspond to the instantaneous value of the rectified AC input line voltage. This is accomplished by connecting a resistor directly between IAC and the rectified input line voltage. The nominal 650mV level present on IAC negates the need for any additional compensating resistors to accommodate for the zero crossings of the line. A current equal to one fourth of the IAC current forms one of the inductor current synthesizer inputs. RVS: The nominal 3V signal present on the VSENSE pin is buffered and brought out to the RVS pin. A current proportional to the output voltage is generated by connecting a resistor between this pin and GND. This current forms the second input to the current synthesizer. VAO: This is the output of the voltage amplifier. At a given input RMS voltage, the voltage on this pin will vary directly with the output load. The output swing is limited from approximately 100mV to 6V. Voltage levels below 1.5V on this pin will inhibit the multiplier output. IMO: This is the output of the multiplier, and the noninverting input of the current amplifier. Since this output is a current, connect a resistor between this pin and ground equal in value to the input resistor of the current amplifier. The common mode operating range for this pin is −0.3V to 5V. VCC: Positive supply rail for the IC. Bypass this pin to GND with a 1µF low ESL, ESR ceramic capacitor. This pin is internally clamped to 20V. Current into this clamp should be limited to less than 10mA. The UC3855A has a 15.5V (nominal) turn on threshold with 6 volts of hysteresis while the UC3855B turns on at 10.5V with 500mV of hysteresis. ION: This pin is the current sensing input. It should be connected to the secondary side output of a current sensing transformer whose primary winding is in series with the boost switch. The resultant signal applied to this input is buffered and level shifted up a diode to the CI capacitor on the CI pin. The ION buffer has a source only output. Discharge of the CI cap is enabled through the current synthesizer circuitry. The current sense transformer termination resistor should be designed to obtain a 1V input signal amplitude at peak switch current. VRMS: This pin is the feedforward line voltage compensation input to the multiplier. A voltage on VRMS proportional to the AC input RMS voltage commands the multiplier to alter the current command signal by 2 1/VRMS to maintain a constant power balance. The input to VRMS is generally derived from a two pole low pass filter/voltage divider connected to the rectified AC input voltage. This feature allows universal input supply voltage operation and faster response to input line fluctuations for the PFC boost preregulator. For most designs, a voltage level of 1.5V on this pin should correspond to low line, and 4.7V for high line. The input range for this pin extends from 0 to 5.5V. OVP: This pin senses the boost output voltage through a voltage divider. The enable comparator input is TTL compatible and can be used as a remote shutdown port. A voltage level below 1.8V, disables VREF, oscillator, and the PWM circuitry via the enable comparator. Between 1.8V and VREF (7.5V) the UC is enabled. Voltage levels above 7.5V will set the PWM latch via the hysteretic OVP comparator and disable both ZVTOUT and GTOUT until the OVP level has decayed by the nominal hysteresis of 400mV. If the voltage divider is designed to initiate an OVP fault at 5% of OV, the internal hysteresis enables normal operation again when the output voltage has reached its nominal regulation level. Both the OVP and enable comparators have direct logical connections to the PWM output and exhibit typical propagation delays of 200ns. VSENSE: This pin is the inverting input of the voltage amplifier and serves as the output voltage feedback point for the PFC boost converter. It senses the output voltage through a voltage divider which produces a nominal 3V. The voltage loop compensation is normally connected between this pin and VAO. The VSENSE pin must be above 1.5V at 25°C, (1.9V at –55°C) for the current synthesizer to work properly. 5 UC2855A/B UC3855A/B PIN DESCRIPTIONS (cont.) ZVS: This pin senses when the drain voltage of the main MOSFET switch has reached approximately zero volts, and resets the ZVT latch via the ZVT comparator. A minimum and maximum ZVTOUT pulse width are programmable from this pin. To directly sense the ≈400V drain voltage of the main switch, a blocking diode is connected between ZVS and the high voltage drain. When the drain reaches 0V, the level on ZVS is ≈0.7V which is below the 2.6V ZVT comparator threshold. The maximum ZVTOUT pulse width is approximately equal to the oscillator blanking period time. ZVTOUT: The output of the ZVT block is a 750mA peak totem pole MOSFET gate driver on ZVTOUT. Since the ZVT MOSFET switch is typically 3X smaller than the main switch, less peak current is required from this output. Like GTOUT, a series gate resistor and Schottky diode to GND are recommended. This pin may also be used as a high current synchronization output driver. For more information see Unitrode Applications Note U-153. 5.992 496 516 MHz 120 Gain -90 100 120 Phase -45 Phase 80 Gain (dB) Phase Margin degrees Degrees 0 60 100 80 60 40 Open-Loop 40 20 Gain dB 0 20 0 -20 0.1 -20 1 10 100 1000 10000 Frequency kHz -40 -60 10kHz 100kHz 1MHz 10MHz log f Figure 1. Current Amplifier Frequency Response Figure 2. Voltage Amplifier Gain Phase vs Frequency 24 3.10 3.08 22 3.06 20 3.04 3.02 18 2.98 mA VOLTS 3.00 2.96 16 14 2.94 12 2.92 2.90 10 -60 -40 -20 0 20 40 60 80 100 120 140 -60 -40 -20 TEMP ERATURE °C 0 20 40 60 TEMP ERATURE °C Figure 3. Voltage Amplifier Input Threshold Figure 4. Supply Current ON 6 80 100 120 140 UC2855A/B UC3855A/B 230 -0.75 225 -0.77 220 -0.79 215 210 -0.83 205 -0.85 200 kHz GAIN CONSTANT (K) -0.81 -0.87 195 190 -0.89 185 -0.91 180 -0.93 175 -0.95 170 -60 -40 -20 0 20 40 60 80 100 120 140 -60 -40 -20 TEMP ERATURE °C 0 20 40 60 TEMP ERATURE °C Figure 5. Multiplier Current Gain Constant Figure 6. Oscillator Initial Accuracy 7 80 100 120 140 UC2855A/B UC3855A/B TYPICAL APPLICATION UDG-95165-1 Figure 7. Typical Application 8 PACKAGE OPTION ADDENDUM www.ti.com 4-Mar-2005 PACKAGING INFORMATION Orderable Device Status (1) Package Type Package Drawing Pins Package Eco Plan (2) Qty Lead/Ball Finish MSL Peak Temp (3) UC2855ADW ACTIVE SOIC DW 20 25 None CU SNPB Level-2-220C-1 YEAR UC2855ADWTR ACTIVE SOIC DW 20 2000 None CU SNPB Level-2-220C-1 YEAR UC2855AN ACTIVE PDIP N 20 20 None CU SNPB Level-NA-NA-NA UC2855BDW ACTIVE SOIC DW 20 25 None CU SNPB Level-2-220C-1 YEAR UC2855BDWG4 ACTIVE SOIC DW 20 1000 Green (RoHS & no Sb/Br) CU NIPDAU Level-2-260C-1 YEAR UC2855BDWTR ACTIVE SOIC DW 20 2000 None CU SNPB Level-2-220C-1 YEAR UC2855BN ACTIVE PDIP N 20 20 None CU SNPB Level-NA-NA-NA UC3855ADW ACTIVE SOIC DW 20 25 None CU SNPB Level-2-220C-1 YEAR UC3855ADWTR ACTIVE SOIC DW 20 2000 None CU SNPB Level-2-220C-1 YEAR UC3855AN ACTIVE PDIP N 20 20 None CU SNPB Level-NA-NA-NA UC3855BDW ACTIVE SOIC DW 20 25 None CU SNPB Level-2-220C-1 YEAR UC3855BDWTR ACTIVE SOIC DW 20 2000 None CU SNPB Level-2-220C-1 YEAR UC3855BN ACTIVE PDIP N 20 20 None CU SNPB Level-NA-NA-NA (1) The marketing status values are defined as follows: ACTIVE: Product device recommended for new designs. LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect. NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in a new design. PREVIEW: Device has been announced but is not in production. Samples may or may not be available. OBSOLETE: TI has discontinued the production of the device. (2) Eco Plan - May not be currently available - please check http://www.ti.com/productcontent for the latest availability information and additional product content details. None: Not yet available Lead (Pb-Free). Pb-Free (RoHS): TI's terms "Lead-Free" or "Pb-Free" mean semiconductor products that are compatible with the current RoHS requirements for all 6 substances, including the requirement that lead not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered at high temperatures, TI Pb-Free products are suitable for use in specified lead-free processes. Green (RoHS & no Sb/Br): TI defines "Green" to mean "Pb-Free" and in addition, uses package materials that do not contain halogens, including bromine (Br) or antimony (Sb) above 0.1% of total product weight. (3) MSL, Peak Temp. -- The Moisture Sensitivity Level rating according to the JEDECindustry standard classifications, and peak solder temperature. Important Information and Disclaimer:The information provided on this page represents TI's knowledge and belief as of the date that it is provided. TI bases its knowledge and belief on information provided by third parties, and makes no representation or warranty as to the accuracy of such information. Efforts are underway to better integrate information from third parties. TI has taken and continues to take reasonable steps to provide representative and accurate information but may not have conducted destructive testing or chemical analysis on incoming materials and chemicals. TI and TI suppliers consider certain information to be proprietary, and thus CAS numbers and other limited information may not be available for release. In no event shall TI's liability arising out of such information exceed the total purchase price of the TI part(s) at issue in this document sold by TI to Customer on an annual basis. Addendum-Page 1 IMPORTANT NOTICE Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, modifications, enhancements, improvements, and other changes to its products and services at any time and to discontinue any product or service without notice. Customers should obtain the latest relevant information before placing orders and should verify that such information is current and complete. All products are sold subject to TI’s terms and conditions of sale supplied at the time of order acknowledgment. TI warrants performance of its hardware products to the specifications applicable at the time of sale in accordance with TI’s standard warranty. Testing and other quality control techniques are used to the extent TI deems necessary to support this warranty. Except where mandated by government requirements, testing of all parameters of each product is not necessarily performed. TI assumes no liability for applications assistance or customer product design. Customers are responsible for their products and applications using TI components. To minimize the risks associated with customer products and applications, customers should provide adequate design and operating safeguards. TI does not warrant or represent that any license, either express or implied, is granted under any TI patent right, copyright, mask work right, or other TI intellectual property right relating to any combination, machine, or process in which TI products or services are used. Information published by TI regarding third-party products or services does not constitute a license from TI to use such products or services or a warranty or endorsement thereof. Use of such information may require a license from a third party under the patents or other intellectual property of the third party, or a license from TI under the patents or other intellectual property of TI. Reproduction of information in TI data books or data sheets is permissible only if reproduction is without alteration and is accompanied by all associated warranties, conditions, limitations, and notices. Reproduction of this information with alteration is an unfair and deceptive business practice. TI is not responsible or liable for such altered documentation. Resale of TI products or services with statements different from or beyond the parameters stated by TI for that product or service voids all express and any implied warranties for the associated TI product or service and is an unfair and deceptive business practice. TI is not responsible or liable for any such statements. Following are URLs where you can obtain information on other Texas Instruments products and application solutions: Products Applications Amplifiers amplifier.ti.com Audio www.ti.com/audio Data Converters dataconverter.ti.com Automotive www.ti.com/automotive DSP dsp.ti.com Broadband www.ti.com/broadband Interface interface.ti.com Digital Control www.ti.com/digitalcontrol Logic logic.ti.com Military www.ti.com/military Power Mgmt power.ti.com Optical Networking www.ti.com/opticalnetwork Microcontrollers microcontroller.ti.com Security www.ti.com/security Telephony www.ti.com/telephony Video & Imaging www.ti.com/video Wireless www.ti.com/wireless Mailing Address: Texas Instruments Post Office Box 655303 Dallas, Texas 75265 Copyright 2005, Texas Instruments Incorporated