NEC PS9117A

DATA SHEET
PHOTOCOUPLER
PS9117A
HIGH CMR, 10 Mbps OPEN COLLECTOR OUTPUT TYPE
5-PIN SOP (SO-5)
HIGH-SPEED PHOTOCOUPLER
−NEPOC
Series−
DESCRIPTION
The PS9117A is an optically coupled high-speed, active low type isolator containing a GaAlAs LED on the input
side and a photodiode and a signal processing circuit on the output side on one chip.
The PS9117A is designed specifically for high common mode transient immunity (CMR) and low pulse width
distortion. The PS9117A is suitable for high density application.
FEATURES
• Pulse width distortion (⏐tPHL − tPLH⏐ = 35 ns MAX.)
PIN CONNECTION
(Top View)
• High common mode transient immunity (CMH, CML = ±15 kV/μs MIN.)
5
• Small package (SO-5)
4
3
• High-speed (10 Mbps)
1. Anode
2. Cathode
3. GND
4. VO
5. VCC
• High isolation voltage (BV = 3 750 Vr.m.s.)
• Open collector output
• Ordering number of taping product: PS9117A-F3: 2 500 pcs/reel
• Pb-Free product
1
2
• Safety standards
• UL approved: File No. E72422
• DIN EN60747-5-2 (VDE0884 Part2) approved No. 40008902 (Option)
TRUTH TABLE
APPLICATIONS
LED
Output
• Measurement equipment
ON
L
• PDP
OFF
H
• FA Network
The information in this document is subject to change without notice. Before using this document, please
confirm that this is the latest version.
Not all products and/or types are available in every country. Please check with an NEC Electronics
sales representative for availability and additional information.
Document No. PN10646EJ04V0DS (4th edition)
Date Published July 2008 NS
Printed in Japan
The mark <R> shows major revised points.
The revised points can be easily searched by copying an "<R>" in the PDF file and specifying it in the "Find what:" field.
2006, 2008
PS9117A
PACKAGE DIMENSIONS (UNIT: mm)
3.4
5
+0.3
–0.1
4
3
7.0±0.3
4.4
2
2.6±0.2
0.15 +0.10
–0.05
1
0.1±0.1
<R>
0.5±0.3
1.27
0.4 +0.10
–0.05
0.25 M
MARKING EXAMPLE
SnBi PLATING
Ni/Pd/Au PLATING
117A
N831
No. 1 pin Mark
Initial of NEC
(Engraved mark)
N
No. 1 pin Mark
Initial of NEC
(Engraved mark)
*1
N
117A
N831
Type Number
Assembly Lot
8 31
*1
2
Bar : Pb-Free
N
N
Week Assembled
Year Assembled
(Last 1 Digit)
Rank Code
Type Number
Assembly Lot
*1
8 31
Week Assembled
Year Assembled
(Last 1 Digit)
Rank Code
*1
Bar : Pb-Free
Data Sheet PN10646EJ04V0DS
PS9117A
<R>
ORDERING INFORMATION
Part Number
Order Number
Solder Plating
Packing Style
Specification
Safety Standards
Application
Approval
Part Number
PS9117A
PS9117A-A
Pb-Free
20 pcs (Tape 20 pcs cut)
Standard products
PS9117A-F3
PS9117A-F3-A
(SnBi)
Embossed Tape 2 500 pcs/reel
(UL approved)
PS9117A-V
PS9117A-V-A
20 pcs (Tape 20 pcs cut)
DIN EN60747-5-2
PS9117A-V-F3
PS9117A-V-F3-A
Embossed Tape 2 500 pcs/reel
(VDE0884 Part2)
*1
PS9117A
approved (Option)
PS9117A
PS9117A-AX
Pb-Free
20 pcs (Tape 20 pcs cut)
Standard products
PS9117A-F3
PS9117A-F3-AX
(Ni/Pd/Au)
Embossed Tape 2 500 pcs/reel
(UL approved)
PS9117A-V
PS9117A-V-AX
20 pcs (Tape 20 pcs cut)
DIN EN60747-5-2
PS9117A-V-F3
PS9117A-V-F3-AX
Embossed Tape 2 500 pcs/reel
(VDE0884 Part2)
approved (Option)
*1 For the application of the Safety Standard, following part number should be used.
ABSOLUTE MAXIMUM RATINGS (TA = 25°C, unless otherwise specified)
Parameter
Symbol
Ratings
Unit
Forward Current
IF
30
mA
Reverse Voltage
VR
5
V
Supply Voltage
VCC
7
V
Output Voltage
VO
7
V
IO
25
mA
PC
40
mW
BV
3 750
Vr.m.s.
Operating Ambient Temperature
TA
−40 to +85
°C
Storage Temperature
Tstg
−55 to +125
°C
Diode
Detector
*1
Output Current
Power Dissipation
Isolation Voltage
*2
*3
*1 Reduced to 0.3 mA/°C at TA = 25°C or more.
*2 Applies to output pin VO (collector pin). Reduced to 1.5 mW/°C at TA = 65°C or more.
*3 AC voltage for 1 minute at TA = 25°C, RH = 60% between input and output.
Pins 1-2 shorted together, 3-5 shorted together.
RECOMMENDED OPERATING CONDITIONS
Parameter
Symbol
MIN.
Low Level Input Voltage
VFL
0
High Level Input Current
IFH
6.3
Supply Voltage
VCC
4.5
TTL (RL = 1 kΩ, loads)
N
Pull-up Resistor
RL
TYP.
MAX.
Unit
0.8
V
10
12.5
mA
5.0
5.5
V
5
330
4k
Data Sheet PN10646EJ04V0DS
Ω
3
PS9117A
ELECTRICAL CHARACTERISTICS (TA = −40 to +85°C, unless otherwise specified)
Parameter
Diode
Symbol
*1
MIN.
TYP.
1.4
1.65
MAX.
Unit
1.8
V
10
μA
Forward Voltage
VF
IF = 10 mA, TA = 25°C
Reverse Current
IR
VR = 3 V, TA = 25°C
Terminal Capacitance
Ct
V = 0 V, f = 1 MHz, TA = 25°C
30
IOH
VCC = VO = 5.5 V, VF = 0.8 V
1
100
μA
VOL
VCC = 5.5 V, IF = 5 mA, IOL = 13 mA
0.2
0.6
V
High Level Supply Current
ICCH
VCC = 5.5 V, IF = 0 mA, VO = open
4
7
mA
Low Level Supply Current
ICCL
VCC = 5.5 V, IF = 10 mA, VO = open
6
10
IFHL
VCC = 5 V, VO = 0.8 V, RL = 350 Ω
2
5
RI-O
VI-O = 1 kVDC, RH = 40 to 60%,
Detector High Level Output Current
<R>
Conditions
Low Level Output Voltage
*2
Coupled Threshold Input Current
pF
(H → L)
Isolation Resistance
10
Ω
11
TA = 25°C
Isolation Capacitance
CI-O
V = 0 V, f = 1 MHz, TA = 25°C
0.6
Propagation Delay Time
tPHL
TA = 25°C
40
(H → L)
*3
pF
75
ns
100
Propagation Delay Time
tPLH
TA = 25°C
45
(L → H)
*3
75
100
Rise Time
tr
VCC = 5 V, RL = 350 Ω, IF = 7.5 mA,
20
Fall Time
tf
VTHHL = VTHLH = 1.5 V
5
Pulse Width Distortion
⏐tPHL-tPLH⏐
5
35
*3
(PWD)
Propagation Delay Skew
tPSK
Common Mode
CMH
Common Mode
4
15
20
kV/μs
15
20
kV/μs
*4
Transient Immunity at Low
Level Output
VCC = 5 V, RL = 350 Ω, TA = 25°C,
IF = 0 mA, VO > 2 V, VCM = 1 kV
Transient Immunity at High
Level Output
40
CML
VCC = 5 V, RL = 350 Ω, TA = 25°C,
IF = 7.5 mA, VO < 0.8 V, VCM = 1 kV
*4
Data Sheet PN10646EJ04V0DS
PS9117A
*1 Typical values at TA = 25°C
*2 Because VOL of 2 V or more may be output when LED current input and when output supply of VCC = 2.6 V or
less, it is important to confirm the characteristics (operation with the power supply on and off) during design,
before using this device.
*3 Test circuit for propagation delay time
(IF = 7.5 mA)
50%
Input
VCC = 5 V
Pulse input (IF)
0.1 μ F
(PW = 1 μ s,
Duty cycle = 1/10)
Input
(monitor)
RL = 350 Ω
VO (monitor)
CL = 15 pF
47 Ω
Output
tPHL
1.5 V
VOL
tPLH
Remark CL includes probe and stray wiring capacitance.
*4 Test circuit for common mode transient immunity
SW
1 kV
VCM 90%
IF
VCC = 5 V
0.1 μ F
10%
RL = 350 Ω
VO (monitor)
CL = 15 pF
0V
tr
VO
(IF = 0 mA)
VCM
VO
(IF = 7.5 mA)
tf
VOH
2V
0.8 V
VOL
Remark CL includes probe and stray wiring capacitance.
USAGE CAUTIONS
1. This product is weak for static electricity by designed with high-speed integrated circuit so protect against static
electricity when handling.
2. By-pass capacitor of 0.1 μF is used between VCC and GND near device. Also, ensure that the distance between
the leads of the photocoupler and capacitor is no more than 10 mm.
3. Avoid storage at a high temperature and high humidity.
Data Sheet PN10646EJ04V0DS
5
PS9117A
TYPICAL CHARACTERISTICS (TA = 25°C, unless otherwise specified)
MAXIMUM FORWARD CURRENT
vs. AMBIENT TEMPERATURE
DETECTOR POWER DISSIPATION
vs. AMBIENT TEMPERATURE
50
Detector Power Dissipation PC (mW)
Maximum Forward Current IF (mA)
40
30
20
10
0
20
40
80 85
60
100
40
80 85
60
SUPPLY CURRENT vs.
AMBIENT TEMPERATURE
100
12
TA = +85˚C
+50˚C
+25˚C
0˚C
–25˚C
1
0.1
1.2
1.4
1.6
1.8
2.0
2.2
10
8
ICCL (IF = 10 mA)
6
ICCH (IF = 0 mA)
4
2
0
–50
2.4
–25
0
25
50
75
100
Forward Voltage VF (V)
Ambient Temperature TA (˚C)
OUTPUT VOLTAGE vs.
FORWARD CURRENT
LOW LEVEL OUTPUT VOLTAGE vs.
AMBIENT TEMPERATURE
0.6
Low Level Output Voltage VOL (V)
VCC = 5.0 V
5
RL = 350 Ω
1.0 kΩ
4
4.0 kΩ, 4.7 kΩ
3
2
1
1
2
3
4
5
6
IF = 5.0 mA,
VCC = 5.5 V
0.5
0.4
IOL = 16.0 mA
13.0 mA
10.0 mA
6.0 mA
0.3
0.2
0.1
0
–50
Forward Current IF (mA)
–25
0
25
50
75
Ambient Temperature TA (˚C)
Remark The graphs indicate nominal characteristics.
6
20
FORWARD CURRENT vs.
FORWARD VOLTAGE
High Level Supply Current ICCH (mA)
Low Level Supply Current ICCL (mA)
Forward Current IF (mA)
10
Ambient Temperature TA (˚C)
6
Output Voltage VO (V)
20
Ambient Temperature TA (˚C)
10
0
30
0
100
0.01
1.0
40
Data Sheet PN10646EJ04V0DS
100
PS9117A
PROPAGATION DELAY TIME vs.
AMBIENT TEMPERATURE
THRESHOLD INPUT CURRENT vs.
AMBIENT TEMPERATURE
100
Propagation Delay Time tPHL, tPLH (ns)
Threshold Input Current IFHL (mA)
5
VCC = 5.0 V,
VO = 0.6 V
4
RL = 350 Ω
3
1.0 kΩ
2
4.0 kΩ
1
0
–50
–25
0
25
50
75
tPLH: RL = 4.0 kΩ
tPLH: RL = 1.0 kΩ
40
20
tPLH: RL = 350 Ω
tPHL: RL = 350 Ω, 1.0 kΩ, 4.0 kΩ, 4.7 kΩ
–25
0
25
50
75
PULSE WIDTH DISTORTION vs.
AMBIENT TEMPERATURE
PROPAGATION DELAY TIME vs.
FORWARD CURRENT
100
100
IF = 7.5 mA,
VCC = 5.0 V
40
30
RL = 4.0 kΩ
20
RL = 1.0 kΩ
10
RL = 350 Ω
–25
0
25
50
75
100
Propagation Delay Time tPHL, tPLH (ns)
Pulse Width Distortion tPHL–tPLH (ns)
60
Ambient Temperature TA (˚C)
RL = 4.7 kΩ
0
–50
tPLH: RL = 4.7 kΩ
Ambient Temperature TA (˚C)
60
50
80
0
–50
100
IF = 7.5 mA,
VCC = 5.0 V
VCC = 5.0 V
tPLH: RL = 4.7 kΩ
80
60
tPLH: RL = 1.0 kΩ
tPLH: RL = 4.0 kΩ
40
tPLH: RL = 350 Ω
20
0
5
Ambient Temperature TA (˚C)
tPHL: RL = 350 Ω, 1.0 kΩ, 4.0 kΩ, 4.7 kΩ
7
9
11
13
15
Forward Current IF (mA)
Remark The graphs indicate nominal characteristics.
Data Sheet PN10646EJ04V0DS
7
PS9117A
TAPING SPECIFICATIONS (UNIT: mm)
1.55±0.1
7.4±0.1
5.5±0.1
1.5+0.1
–0
12.0±0.2
2.0±0.05
4.0±0.1
1.75±0.1
Outline and Dimensions (Tape)
3.9±0.1
8.0±0.1
3.45 MAX.
3.0±0.1
0.3±0.05
Tape Direction
PS9117A-F3
Outline and Dimensions (Reel)
2.0±0.5
2.0±0.5
φ 100±1.0
21.0±0.8
φ 13.0±0.2
R 1.0
φ 330±2.0
13.0±0.2
13.5±1.0
17.5±1.0
Packing: 2 500 pcs/reel
8
Data Sheet PN10646EJ04V0DS
11.9 to 15.4
Outer edge of
flange
PS9117A
RECOMMENDED MOUNT PAD DIMENSIONS (UNIT: mm)
0.8
1.45
1.27
<R>
5.5
Data Sheet PN10646EJ04V0DS
9
PS9117A
NOTES ON HANDLING
1. Recommended soldering conditions
(1) Infrared reflow soldering
• Peak reflow temperature
260°C or below (package surface temperature)
• Time of peak reflow temperature
10 seconds or less
• Time of temperature higher than 220°C
60 seconds or less
• Time to preheat temperature from 120 to 180°C
120±30 s
• Number of reflows
Three
• Flux
Rosin flux containing small amount of chlorine (The flux with a
maximum chlorine content of 0.2 Wt% is recommended.)
Package Surface Temperature T (˚C)
Recommended Temperature Profile of Infrared Reflow
(heating)
to 10 s
260˚C MAX.
220˚C
to 60 s
180˚C
120˚C
120±30 s
(preheating)
Time (s)
(2) Wave soldering
• Temperature
260°C or below (molten solder temperature)
• Time
10 seconds or less
• Preheating conditions
120°C or below (package surface temperature)
• Number of times
One (Allowed to be dipped in solder including plastic mold portion.)
• Flux
Rosin flux containing small amount of chlorine (The flux with a maximum chlorine
content of 0.2 Wt% is recommended.)
(3) Soldering by Soldering Iron
• Peak Temperature (lead part temperature)
350°C or below
• Time (each pins)
3 seconds or less
• Flux
Rosin flux containing small amount of chlorine (The flux with a
maximum chlorine content of 0.2 Wt% is recommended.)
(a) Soldering of leads should be made at the point 1.5 to 2.0 mm from the root of the lead
(b) Please be sure that the temperature of the package would not be heated over 100°C
10
Data Sheet PN10646EJ04V0DS
PS9117A
(4) Cautions
• Fluxes
Avoid removing the residual flux with freon-based and chlorine-based cleaning solvent.
2. Cautions regarding noise
Be aware that when voltage is applied suddenly between the photocoupler’s input and output or between
collector-emitters at startup, the output transistor may enter the on state, even if the voltage is within the absolute
maximum ratings.
USAGE CAUTIONS
1. Protect against static electricity when handling.
2. Avoid storage at a high temperature and high humidity.
Data Sheet PN10646EJ04V0DS
11
PS9117A
<R>
SPECIFICATION OF VDE MARKS LICENSE DOCUMENT
Parameter
Symbol
Speck
Unit
Application classification (DIN EN 60664-1 VDE0110 Part 1)
for rated line voltages ≤ 300 Vr.m.s.
IV
for rated line voltages ≤ 600 Vr.m.s.
III
Climatic test class (DIN EN 60664-1 VDE0110)
40/85/21
Dielectric strength
maximum operating isolation voltage
Test voltage (partial discharge test, procedure a for type test and random test)
UIORM
707
Vpeak
Upr
1 061
Vpeak
Upr
1 326
Vpeak
UTR
6 000
Vpeak
Upr = 1.5 × UIORM, Pd < 5 pC
Test voltage (partial discharge test, procedure b for all devices)
Upr = 1.875 × UIORM, Pd < 5 pC
Highest permissible overvoltage
Degree of pollution (DIN EN 60664-1 VDE0110 Part 1)
2
Clearance distance
>4.2
mm
Creepage distance
>4.2
mm
Comparative tracking index (DIN IEC 112/VDE 0303 Part 1)
CTI
Material group (DIN EN 60664-1 VDE0110 Part 1)
175
III a
Storage temperature range
Tstg
–55 to +125
°C
Operating temperature range
TA
–40 to +85
°C
VIO = 500 V dc at TA = 25°C
Ris MIN.
10
12
Ω
VIO = 500 V dc at TA MAX. at least 100°C
Ris MIN.
10
11
Ω
Package temperature
Tsi
150
°C
Current (input current IF, Psi = 0)
Isi
200
mA
Power (output or total power dissipation)
Psi
300
mW
Ris MIN.
10
Isolation resistance, minimum value
Safety maximum ratings (maximum permissible in case of fault, see thermal
derating curve)
Isolation resistance
VIO = 500 V dc at TA = Tsi
12
Data Sheet PN10646EJ04V0DS
9
Ω
PS9117A
• The information in this document is current as of July, 2008. The information is subject to change
without notice. For actual design-in, refer to the latest publications of NEC Electronics data sheets or
data books, etc., for the most up-to-date specifications of NEC Electronics products. Not all
products and/or types are available in every country. Please check with an NEC Electronics sales
representative for availability and additional information.
• No part of this document may be copied or reproduced in any form or by any means without the prior
written consent of NEC Electronics. NEC Electronics assumes no responsibility for any errors that may
appear in this document.
• NEC Electronics does not assume any liability for infringement of patents, copyrights or other intellectual
property rights of third parties by or arising from the use of NEC Electronics products listed in this document
or any other liability arising from the use of such products. No license, express, implied or otherwise, is
granted under any patents, copyrights or other intellectual property rights of NEC Electronics or others.
• Descriptions of circuits, software and other related information in this document are provided for illustrative
purposes in semiconductor product operation and application examples. The incorporation of these
circuits, software and information in the design of a customer's equipment shall be done under the full
responsibility of the customer. NEC Electronics assumes no responsibility for any losses incurred by
customers or third parties arising from the use of these circuits, software and information.
• While NEC Electronics endeavors to enhance the quality, reliability and safety of NEC Electronics products,
customers agree and acknowledge that the possibility of defects thereof cannot be eliminated entirely. To
minimize risks of damage to property or injury (including death) to persons arising from defects in NEC
Electronics products, customers must incorporate sufficient safety measures in their design, such as
redundancy, fire-containment and anti-failure features.
• NEC Electronics products are classified into the following three quality grades: "Standard", "Special" and
"Specific".
The "Specific" quality grade applies only to NEC Electronics products developed based on a customerdesignated "quality assurance program" for a specific application. The recommended applications of an NEC
Electronics product depend on its quality grade, as indicated below. Customers must check the quality grade of
each NEC Electronics product before using it in a particular application.
"Standard": Computers, office equipment, communications equipment, test and measurement equipment, audio
and visual equipment, home electronic appliances, machine tools, personal electronic equipment
and industrial robots.
"Special": Transportation equipment (automobiles, trains, ships, etc.), traffic control systems, anti-disaster
systems, anti-crime systems, safety equipment and medical equipment (not specifically designed
for life support).
"Specific": Aircraft, aerospace equipment, submersible repeaters, nuclear reactor control systems, life
support systems and medical equipment for life support, etc.
The quality grade of NEC Electronics products is "Standard" unless otherwise expressly specified in NEC
Electronics data sheets or data books, etc. If customers wish to use NEC Electronics products in applications
not intended by NEC Electronics, they must contact an NEC Electronics sales representative in advance to
determine NEC Electronics' willingness to support a given application.
(Note)
(1) "NEC Electronics" as used in this statement means NEC Electronics Corporation and also includes its
majority-owned subsidiaries.
(2) "NEC Electronics products" means any product developed or manufactured by or for NEC Electronics (as
defined above).
M8E 02. 11-1
Data Sheet PN10646EJ04V0DS
13
PS9117A
Caution
GaAs Products
This product uses gallium arsenide (GaAs).
GaAs vapor and powder are hazardous to human health if inhaled or ingested, so please observe
the following points.
• Follow related laws and ordinances when disposing of the product. If there are no applicable laws
and/or ordinances, dispose of the product as recommended below.
1. Commission a disposal company able to (with a license to) collect, transport and dispose of
materials that contain arsenic and other such industrial waste materials.
2. Exclude the product from general industrial waste and household garbage, and ensure that the
product is controlled (as industrial waste subject to special control) up until final disposal.
• Do not burn, destroy, cut, crush, or chemically dissolve the product.
• Do not lick the product or in any way allow it to enter the mouth.