TI SN65ALS180DR

SN65ALS180, SN75ALS180
DIFFERENTIAL DRIVER AND RECEIVER PAIRS
SLLS052G – AUGUST 1987 – REVISED APRIL 2003
D
D
D
D
D
D
D
D
D
D
D
D
D
D
D
SN65ALS180 . . . D PACKAGE
SN75ALS180 . . . D OR N PACKAGE
(TOP VIEW)
Meet or Exceed the Requirements of
TIA/EIA-422-B, TIA/EIA-485-A† and
ITU Recommendation V.11
High-Speed Advanced Low-Power Schottky
Circuitry
Designed for 25-Mbaud Operation in Both
Serial and Parallel Applications
Low Skew Between Devices . . . 6 ns Max
Low Supply-Current Requirements
. . . 30 mA Max
Individual Driver and Receiver I/O Pins With
Dual VCC and Dual GND
Wide Positive and Negative Input/Output
Bus Voltage Ranges
Driver Output Capacity . . . ±60 mA
Thermal Shutdown Protection
Driver Positive- and Negative-Current
Limiting
Receiver Input Impedance . . . 12 kΩ Min
Receiver Input Sensitivity . . . ±200 mV Max
Receiver Input Hysteresis . . . 60 mV Typ
Operate From a Single 5-V Supply
Glitch-Free Power-Up and Power-Down
Protection
NC
R
RE
DE
D
GND
GND
1
14
2
13
3
12
4
11
5
10
6
9
7
8
VCC
VCC
A
B
Z
Y
NC
NC – No internal connection
description/ordering information
The SN65ALS180 and SN75ALS180 differential driver and receiver pairs are integrated circuits designed for
bidirectional data communication on multipoint bus-transmission lines. They are designed for balanced
transmission lines and meet TIA/EIA-422-B, TIA/EIA-485-A, and ITU Recommendation V.11.
ORDERING INFORMATION
PACKAGE†
TA
PDIP (N)
0°C to 70°C
–40°C to 85°C
SOIC (D)
SOIC (D)
ORDERABLE
PART NUMBER
Tube of 25
SN75ALS180N
Tube of 50
SN75ALS180D
Reel of 2500
SN75ALS180DR
Tube of 50
SN65ALS180D
Reel of 2500
SN65ALS180DR
TOP-SIDE
MARKING
SN75ALS180N
75ALS180
65ALS180
† Package drawings, standard packing quantities, thermal data, symbolization, and PCB design guidelines are
available at www.ti.com/sc/package.
Please be aware that an important notice concerning availability, standard warranty, and use in critical applications of
Texas Instruments semiconductor products and disclaimers thereto appears at the end of this data sheet.
† These devices meet or exceed the requirements of TIA/EIA-485-A, except for the Generator Contention Test (para. 3.4.2) and the Generator
Current Limit (para. 3.4.3). The applied test voltage ranges are –6 V to 8 V for the SN75ALS180 and –4 V to 8 V for the SN65ALS180.
Copyright  2003, Texas Instruments Incorporated
PRODUCTION DATA information is current as of publication date.
Products conform to specifications per the terms of Texas Instruments
standard warranty. Production processing does not necessarily include
testing of all parameters.
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
1
SN65ALS180, SN75ALS180
DIFFERENTIAL DRIVER AND RECEIVER PAIRS
SLLS052G – AUGUST 1987 – REVISED APRIL 2003
description/ordering information (continued)
The SN65ALS180 and SN75ALS180 combine a 3-state differential line driver and a differential input line
receiver, both of which operate from a single 5-V power supply. The driver and receiver have active-high and
active-low enables, respectively, that can be connected together externally to function as a direction control.
The driver differential outputs and the receiver differential inputs are connected to separate terminals for greater
flexibility and are designed to offer minimum loading to the bus when the driver is disabled or VCC = 0.
These ports feature wide positive and negative common-mode voltage ranges, making the device suitable for
party-line applications.
Function Tables
DRIVER
OUTPUTS
INPUT
D
ENABLE
DE
H
H
H
L
L
H
L
H
X
L
Z
Z
Y
Z
RECEIVER
DIFFERENTIAL INPUTS
A–B
ENABLE
RE
OUTPUT
R
VID ≥ 0.2 V
–0.2 V < VID < 0.2 V
L
H
L
?
VID ≤ –0.2 V
X
L
L
H
Z
Open
L
H
H = high level, L = low level, ? = indeterminate,
X = irrelevant, Z = high impedance (off)
logic diagram (positive logic)
DE
D
RE
4
5
9
10
3
12
R
2
2
POST OFFICE BOX 655303
11
Y
Z
A
B
• DALLAS, TEXAS 75265
SN65ALS180, SN75ALS180
DIFFERENTIAL DRIVER AND RECEIVER PAIRS
SLLS052G – AUGUST 1987 – REVISED APRIL 2003
schematics of inputs and outputs
EQUIVALENT OF EACH INPUT
RECEIVER A INPUT
VCC
RECEIVER B INPUT
VCC
VCC
180 kΩ
NOM
R(eq)
3 kΩ
NOM
18 kΩ
NOM
18 kΩ
NOM
Input
3 kΩ
NOM
Input
Input
180 kΩ
NOM
1.1 kΩ
NOM
1.1 kΩ
NOM
Driver and Driver Enable Inputs: R(eq) = 12 kΩ NOM
Receiver Enable Input: R(eq) = 30 kΩ NOM
R(eq) = Equivalent Resistor
DRIVER OUTPUT
VCC
TYPICAL OF RECEIVER OUTPUT
85 Ω
NOM
VCC
Output
Output
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
3
SN65ALS180, SN75ALS180
DIFFERENTIAL DRIVER AND RECEIVER PAIRS
SLLS052G – AUGUST 1987 – REVISED APRIL 2003
absolute maximum ratings over operating free-air temperature range (unless otherwise noted)†
Supply voltage, VCC (see Note 1) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 V
Voltage range at any bus terminal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . –10 V to 15 V
Enable input voltage, VI . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5.5 V
Package thermal impedance, θJA (see Notes 2 and 3): D package . . . . . . . . . . . . . . . . . . . . . . . . . . . . 86°C/W
N package . . . . . . . . . . . . . . . . . . . . . . . . . . . . 80°C/W
Operating virtual junction temperature, TJ . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 150°C
Lead temperature 1,6 mm (1/16 inch) from case for 10 seconds . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 260°C
Storage temperature range, Tst . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . –65°C to 150°C
† Stresses beyond those listed under “absolute maximum ratings” may cause permanent damage to the device. These are stress ratings only, and
functional operation of the device at these or any other conditions beyond those indicated under “recommended operating conditions” is not
implied. Exposure to absolute-maximum-rated conditions for extended periods may affect device reliability.
NOTES: 1. All voltage values, except differential I/O bus voltage, are with respect to network ground terminal.
2. Maximum power dissipation is a function of TJ(max), θJA, and TA. The maximum allowable power dissipation at any allowable
ambient temperature is PD = (TJ(max) – TA)/θJA. Operating at the absolute maximum TJ of 150°C can affect reliability.
3. The package thermal impedance is calculated in accordance with JESD 51-7.
recommended operating conditions
VCC
Supply voltage
MIN
NOM
MAX
UNIT
4.75
5
5.25
V
12
VI or VIC
Voltage at any bus terminal (separately or common mode)
VIH
VIL
High-level input voltage
D, DE, and RE
Low-level input voltage
D, DE, and RE
VID
Differential input voltage (see Note 4)
IOH
High level output current
High-level
IOL
Low level output current
Low-level
TA
Operating free-air
free air temperature
–7
2
Driver
Receiver
Driver
V
0.8
V
±12
V
–60
mA
–400
µA
60
Receiver
8
SN65ALS180
–40
85
SN75ALS180
0
70
NOTE 4: Differential-input/output bus voltage is measured at the noninverting terminal, A/Y, with respect to the inverting terminal, B/Z.
4
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
V
mA
°C
SN65ALS180, SN75ALS180
DIFFERENTIAL DRIVER AND RECEIVER PAIRS
SLLS052G – AUGUST 1987 – REVISED APRIL 2003
DRIVERS
electrical characteristics over recommended ranges of supply voltage and operating free-air
temperature range (unless otherwise noted)
TEST CONDITIONS†
PARAMETER
VIK
VO
Input clamp voltage
Output voltage
II = –18 mA
IO = 0
|VOD1|
Differential output voltage
IO = 0
|VOD2|
g
Differential output voltage
MIN
MAX
UNIT
–1.5
V
0
6
V
1.5
6
V
RL = 100 Ω,
See Figure 1
1/2 VOD1
or 2§
RL = 54 Ω,
See Figure 1
1.5
1.5
VOD3
Differential output voltage
Vtest = –7 V to 12 V,
See Figure 2
∆|VOD|
Change in magnitude of
differential output voltage¶
RL = 54 Ω or 100 Ω,
VOC
Common-mode output voltage
∆|VOC|
TYP‡
V
2.5
5
5
V
See Figure 1
±0.2
V
RL = 54 Ω or 100 Ω,
See Figure 1
3
–1
V
Change in magnitude of
common-mode output voltage¶
RL = 54 Ω or 100 Ω,
See Figure 1
±0.2
V
IO
Output current
Output disabled
(see Note 5)
VO = 12 V
VO = –7 V
IIH
IIL
High-level input current
IOS
ICC
Low-level input current
Short-circuit output current#
y current
Supply
1
–0.8
VI = 2.4 V
VI = 0.4 V
mA
20
µA
–400
µA
VO = –6 V
VO = –4 V
SN75ALS180
–250
SN65ALS180
–250
VO = 0
VO = VCC
All
–150
All
250
VO = 8 V
All
250
No load
Driver outputs enabled,
Receiver disabled
25
30
Outputs disabled
19
26
mA
mA
† The power-off measurement in TIA/EIA-422-B applies to disabled outputs only and is not applied to combined inputs and outputs.
‡ All typical values are at VCC = 5 V, TA = 25°C.
§ The minimum VOD2 with 100-Ω load is either 1/2 VOD2 or 2 V, whichever is greater.
¶ ∆|VOD| and ∆|VOC| are the changes in magnitude of VOD and VOC, respectively, that occur when the input is changed from a high level to a low
level.
# Duration of the short circuit should not exceed one second for this test.
NOTE 5: This applies for both power on and off; refer to TIA/EIA-485-A for exact conditions. The TIA/EIA-422-B limit does not apply for a combined
driver and receiver terminal.
switching characteristics over recommended ranges of supply voltage and operating free-air
temperature
PARAMETER
TEST CONDITIONS
MIN
TYP‡
MAX
3
8
13
ns
1
6
ns
UNIT
Differential output delay time
RL = 54 Ω,
CL = 50 pF,
See Figure 3
Pulse skew (td(ODH) – td(ODL))
RL = 54 Ω,
CL = 50 pF,
See Figure 3
tt(OD)
tPZH
Differential output transition time
RL = 54 Ω,
CL = 50 pF,
See Figure 3
8
13
ns
Output enable time to high level
RL = 110 Ω,
See Figure 4
23
50
ns
tPZL
tPHZ
Output enable time to low level
RL = 110 Ω,
See Figure 5
19
24
ns
Output disable time from high level
RL = 110 Ω,
See Figure 4
8
13
ns
RL = 110 Ω,
See Figure 5
8
13
ns
td(OD)
tPLZ
Output disable time from low level
‡ All typical values are at VCC = 5 V and TA = 25°C.
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
3
5
SN65ALS180, SN75ALS180
DIFFERENTIAL DRIVER AND RECEIVER PAIRS
SLLS052G – AUGUST 1987 – REVISED APRIL 2003
SYMBOL EQUIVALENTS
DATA-SHEET
PARAMETER
TIA/EIA-422-B
TIA/EIA-485-A
VO
|VOD1|
Voa, Vob
Vo
Voa, Vob
Vo
|VOD2|
Vt (RL = 100 Ω)
Vt (RL = 54 Ω)
Vt
(test termination measurement 2)
|VOD3|
Vtest
∆|VOD|
VOC
∆|VOC|
IOS
IO
Vtst
||Vt| – |Vt||
||Vt| – |Vt||
|Vos|
|Vos – Vos|
|Isa|, |Isb|
|Vos|
|Vos – Vos|
|Ixa|, |Ixb|
Iia, Iib
RECEIVERS
electrical characteristics over recommended ranges of common-mode input voltage, supply
voltage, and operating free-air temperature (unless otherwise noted)
PARAMETER
TEST CONDITIONS
VIT+
Positive-going input threshold
voltage
VO = 2.7 V,
IO = –0.4 mA
VIT–
Negative-going input threshold
voltage
VO = 0.5 V,
IO = 8 mA
Vhys
VIK
Hysteresis voltage (VIT+ – VIT–)
VOH
VOL
High-level output voltage
IOZ
High-impedance-state output current
II
Line input current
IIH
IIL
High-level enable-input current
ri
Input resistance
IOS
Short-circuit output current
VID = 200 mV,
ICC
y current
Supply
No load
Enable-input clamp voltage
Low-level output voltage
Low-level enable-input current
MIN
TYP†
MAX
0.2
–0.2‡
VID = –200 mV,
VO = 0.4 V to 2.4 V
Other input = 0 V
(see Note 6)
mV
–1.5
IOH = –400 µA,
IOL = 8 mA,
See Figure 6
2.7
VI = 12 V
VI = –7 V
0.45
V
±20
µA
1
–0.8
VIH = 2.7 V
VIL = 0.4 V
20
–100
12
Outputs disabled
V
V
See Figure 6
VO = 0
Receiver outputs enabled,
Driver inputs disabled
V
V
60
II = –18 mA
VID = 200 mV,
UNIT
mA
µA
µA
kΩ
–15
–85
19
30
19
26
mA
mA
† All typical values are at VCC = 5 V, TA = 25°C.
‡ The algebraic convention, in which the less positive (more negative) limit is designated minimum, is used in this data sheet for common-mode
input voltage and threshold voltage levels only.
NOTE 6: This applies for both power on and power off. Refer to TIA/EIA-485-A for exact conditions.
6
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
SN65ALS180, SN75ALS180
DIFFERENTIAL DRIVER AND RECEIVER PAIRS
SLLS052G – AUGUST 1987 – REVISED APRIL 2003
switching characteristics over recommended ranges of supply voltage and operating free-air
temperature
PARAMETER
TEST CONDITIONS
MIN
TYP†
MAX
UNIT
tPLH
Propagation delay time, low- to high-level output
VID = –1.5 V to 1.5 V,
See Figure 7
CL = 15 pF,
9
14
19
ns
tPHL
Propagation delay time, high- to low-level output
VID = –1.5 V to 1.5 V,
See Figure 7
CL = 15 pF,
9
14
19
ns
Skew (|tPHL – tPLH|)
VID = –1.5 V to 1.5 V,
See Figure 7
CL = 15 pF,
2
6
ns
tPZH
tPZL
Output enable time to high level
CL = 15 pF,
See Figure 8
7
14
ns
Output enable time to low level
CL = 15 pF,
See Figure 8
7
14
ns
tPHZ
tPLZ
Output disable time from high level
CL = 15 pF,
See Figure 8
20
35
ns
Output disable time from low level
CL = 15 pF,
See Figure 8
8
17
ns
† All typical values are at VCC = 5 V, TA = 25°C.
PARAMETER MEASUREMENT INFORMATION
RL
2
VOD2
RL
2
VOC
Figure 1. Driver VOD and VOC
375 Ω
VOD3
60 Ω
375 Ω
Vtest
Figure 2. Driver VOD3
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
7
SN65ALS180, SN75ALS180
DIFFERENTIAL DRIVER AND RECEIVER PAIRS
SLLS052G – AUGUST 1987 – REVISED APRIL 2003
PARAMETER MEASUREMENT INFORMATION
3V
Input
CL = 50 pF
(see Note A)
Generator
(see Note B)
1.5 V
0V
td(ODL)
td(ODH)
Output
RL = 54 Ω
50 Ω
1.5 V
50%
10%
Output
3V
≈2.5 V
90%
50%
10%
≈–2.5 V
tt(OD)
tt(OD)
TEST CIRCUIT
VOLTAGE WAVEFORMS
NOTES: A. CL includes probe and jig capacitance.
B. The input pulse is supplied by a generator having the following characteristics: PRR ≤ 1 MHz, 50% duty cycle, tr ≤ 6 ns, tf ≤ 6 ns,
ZO = 50 Ω.
Figure 3. Driver Test Circuit and Voltage Waveforms
Output
3V
S1
Input
0 V or 3 V
1.5 V
1.5 V
0V
Generator
(see Note B)
CL = 50 pF
(see Note A)
tPZH
RL = 110 Ω
50 Ω
0.5 V
VOH
Output
2.3 V
Voff ≈ 0 V
tPHZ
TEST CIRCUIT
VOLTAGE WAVEFORMS
NOTES: A. CL includes probe and jig capacitance.
B. The input pulse is supplied by a generator having the following characteristics: PRR ≤ 1 MHz, 50% duty cycle, tr ≤ 6 ns, tf ≤ 6 ns,
ZO = 50 Ω.
Figure 4. Driver Test Circuit and Voltage Waveforms
5V
RL = 110 Ω
3V
S1
Output
0 V or 3 V
CL = 50 pF
(see Note A)
Generator
(see Note B)
Input
1.5 V
1.5 V
0V
tPZL
tPLZ
50 Ω
Output
2.3 V
5V
0.5 V
VOL
TEST CIRCUIT
VOLTAGE WAVEFORMS
NOTES: A. CL includes probe and jig capacitance.
B. The input pulse is supplied by a generator having the following characteristics: PRR ≤ 1 MHz, 50% duty cycle, tr ≤ 6 ns, tf ≤ 6 ns,
ZO = 50 Ω.
Figure 5. Driver Test Circuit and Voltage Waveforms
8
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
SN65ALS180, SN75ALS180
DIFFERENTIAL DRIVER AND RECEIVER PAIRS
SLLS052G – AUGUST 1987 – REVISED APRIL 2003
PARAMETER MEASUREMENT INFORMATION
VID
VOH
+IOL
–IOH
VOL
Figure 6. Receiver VOH and VOL
3V
Input
1.5 V
1.5 V
0V
Generator
(see Note B)
tPLH
Output
51 Ω
1.5 V
CL = 15 pF
(see Note A)
tPHL
VOH
Output
1.3 V
1.3 V
0V
VOL
TEST CIRCUIT
VOLTAGE WAVEFORMS
NOTES: A. CL includes probe and jig capacitance.
B. The input pulse is supplied by a generator having the following characteristics: PRR ≤ 1 MHz, 50% duty cycle, tr ≤ 6 ns, tf ≤ 6 ns,
ZO = 50 Ω.
Figure 7. Receiver Test Circuit and Voltage Waveforms
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
9
SN65ALS180, SN75ALS180
DIFFERENTIAL DRIVER AND RECEIVER PAIRS
SLLS052G – AUGUST 1987 – REVISED APRIL 2003
PARAMETER MEASUREMENT INFORMATION
S1
1.5 V
2 kΩ
– 1.5 V
S2
5V
CL = 15 pF
(see Note A)
Generator
(see Note B)
5 kΩ
1N916 or Equivalent
50 Ω
S3
TEST CIRCUIT
3V
Input
3V
S1 to 1.5 V
S2 Open
S3 Closed
1.5 V
Input
1.5 V
0V
tPZH
tPZL
0V
≈4.5 V
VOH
Output
1.5 V
1.5 V
Output
VOL
0V
3V
Input
1.5 V
tPHZ
S1 to 1.5 V
S2 Closed
S3 Closed
3V
Input
1.5 V
S1 to –1.5 V
S2 Closed
S3 Closed
0V
0V
tPLZ
VOH
Output
S1 to –1.5 V
S2 Closed
S3 Open
0.5 V
Output
≈1.3 V
≈1.3 V
0.5 V
VOL
VOLTAGE WAVEFORMS
NOTES: A. CL includes probe and jig capacitance.
B. The input pulse is supplied by a generator having the following characteristics: PRR ≤ 1 MHz, 50% duty cycle, tr ≤ 6 ns, tf ≤ 6 ns,
ZO = 50 Ω.
Figure 8. Receiver Test Circuit and Voltage Waveforms
10
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
SN65ALS180, SN75ALS180
DIFFERENTIAL DRIVER AND RECEIVER PAIRS
SLLS052G – AUGUST 1987 – REVISED APRIL 2003
TYPICAL CHARACTERISTICS – DRIVERS
LOW-LEVEL OUTPUT VOLTAGE
vs
LOW-LEVEL OUTPUT CURRENT
5
4.5
4.5
VOL – Low-Level Output Voltage – V
5
4
3.5
3
2.5
2
1.5
1
VCC = 5 V
TA = 25°C
0.5
VCC = 5 V
TA = 25°C
4
3.5
3
2.5
2
1.5
1
0.5
0
0
0
–20
–40
–60
–80
–100
0
–120
20
IOH – High-Level Output Current – mA
40
60
80
100
120
IOL – Low-Level Output Current – mA
Figure 10
Figure 9
DIFFERENTIAL OUTPUT VOLTAGE
vs
OUTPUT CURRENT
4
VOD – Differential Output Voltage – V
VOH – High-Level Output Voltage – V
HIGH-LEVEL OUTPUT VOLTAGE
vs
HIGH-LEVEL OUTPUT CURRENT
3.5
3
2.5
2
1.5
1
0.5
0
VCC = 5 V
TA = 25°C
0
10
20
30
40
50
60
70
80
90
100
IO – Output Current – mA
Figure 11
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
11
SN65ALS180, SN75ALS180
DIFFERENTIAL DRIVER AND RECEIVER PAIRS
SLLS052G – AUGUST 1987 – REVISED APRIL 2003
TYPICAL CHARACTERISTICS – RECEIVERS
HIGH-LEVEL OUTPUT VOLTAGE
vs
HIGH-LEVEL OUTPUT CURRENT
HIGH-LEVEL OUTPUT VOLTAGE
vs
FREE-AIR TEMPERATURE
5
VID = 0.2 V
TA = 25°C
VOH – High-Level Output Voltage – V
VOH – High-Level Output Voltage – V
5
4
3
VCC = 5.25 V
VCC = 5 V
2
VCC = 4.75 V
1
–10
–20
–30
–40
3
2
1
0
–40
0
0
4
VCC = 5 V
VID = 200 mV
IOH = –440 µA
–50
–20
0
60
80
100
120
Figure 13
Figure 12
LOW-LEVEL OUTPUT VOLTAGE
vs
LOW-LEVEL OUTPUT CURRENT
LOW-LEVEL OUTPUT VOLTAGE
vs
FREE-AIR TEMPERATURE
0.6
0.6
VCC = 5 V
TA = 25°C
VID = –200 mV
0.5
VOL – Low-Level Output Voltage – V
VOL – Low-Level Output Voltage – V
40
TA – Free-Air Temperature – °C
IOH – High-Level Output Current – mA
0.4
0.3
0.2
0.1
0
0
5
10
15
20
25
30
0.5
VCC = 5 V
VID = –200 mA
IOL = 8 mA
0.4
0.3
0.2
0.1
0
–40
–20
0
20
40
Figure 14
Figure 15
POST OFFICE BOX 655303
60
80
TA – Free-Air Temperature – °C
IOL – Low-Level Output Current – mA
12
20
• DALLAS, TEXAS 75265
100
120
SN65ALS180, SN75ALS180
DIFFERENTIAL DRIVER AND RECEIVER PAIRS
SLLS052G – AUGUST 1987 – REVISED APRIL 2003
TYPICAL CHARACTERISTICS – RECEIVERS
OUTPUT VOLTAGE
vs
ENABLE VOLTAGE
OUTPUT VOLTAGE
vs
ENABLE VOLTAGE
5
VCC = 4.75 V
3
VID = 0.2 V
Load = 1 kΩ to VCC
TA = 25°C
5
VO – Output Voltage – V
4
VO – Output Voltage – V
6
VID = 0.2 V
Load = 8 kΩ to GND
TA = 25°C
VCC = 5.25 V
VCC = 5 V
2
1
VCC = 5.25 V
VCC = 4.75 V
4
VCC = 5 V
3
2
1
0
0
0.5
1
1.5
2
2.5
0
3
0
0.5
VI – Enable Voltage – V
1
1.5
2
2.5
3
VI – Enable Voltage – V
Figure 16
Figure 17
APPLICATION INFORMATION
SN65ALS180
SN75ALS180
SN65ALS180
SN75ALS180
RT
RT
Up to
32 Transceivers
NOTE A: The line should terminate at both ends in its characteristic impedance (RT = ZO). Stub lengths off the main line should be kept as short
as possible.
Figure 18. Typical Application Circuit
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
13
IMPORTANT NOTICE
Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, modifications, enhancements,
improvements, and other changes to its products and services at any time and to discontinue any product or service without notice.
Customers should obtain the latest relevant information before placing orders and should verify that such information is current and
complete. All products are sold subject to TI’s terms and conditions of sale supplied at the time of order acknowledgment.
TI warrants performance of its hardware products to the specifications applicable at the time of sale in accordance with TI’s
standard warranty. Testing and other quality control techniques are used to the extent TI deems necessary to support this
warranty. Except where mandated by government requirements, testing of all parameters of each product is not necessarily
performed.
TI assumes no liability for applications assistance or customer product design. Customers are responsible for their products and
applications using TI components. To minimize the risks associated with customer products and applications, customers should
provide adequate design and operating safeguards.
TI does not warrant or represent that any license, either express or implied, is granted under any TI patent right, copyright, mask
work right, or other TI intellectual property right relating to any combination, machine, or process in which TI products or services
are used. Information published by TI regarding third-party products or services does not constitute a license from TI to use such
products or services or a warranty or endorsement thereof. Use of such information may require a license from a third party under
the patents or other intellectual property of the third party, or a license from TI under the patents or other intellectual property of TI.
Reproduction of information in TI data books or data sheets is permissible only if reproduction is without alteration and is
accompanied by all associated warranties, conditions, limitations, and notices. Reproduction of this information with alteration is an
unfair and deceptive business practice. TI is not responsible or liable for such altered documentation.
Resale of TI products or services with statements different from or beyond the parameters stated by TI for that product or service
voids all express and any implied warranties for the associated TI product or service and is an unfair and deceptive business
practice. TI is not responsible or liable for any such statements.
TI products are not authorized for use in safety-critical applications (such as life support) where a failure of the TI product would
reasonably be expected to cause severe personal injury or death, unless officers of the parties have executed an agreement
specifically governing such use. Buyers represent that they have all necessary expertise in the safety and regulatory ramifications
of their applications, and acknowledge and agree that they are solely responsible for all legal, regulatory and safety-related
requirements concerning their products and any use of TI products in such safety-critical applications, notwithstanding any
applications-related information or support that may be provided by TI. Further, Buyers must fully indemnify TI and its
representatives against any damages arising out of the use of TI products in such safety-critical applications.
TI products are neither designed nor intended for use in military/aerospace applications or environments unless the TI products are
specifically designated by TI as military-grade or "enhanced plastic." Only products designated by TI as military-grade meet military
specifications. Buyers acknowledge and agree that any such use of TI products which TI has not designated as military-grade is
solely at the Buyer's risk, and that they are solely responsible for compliance with all legal and regulatory requirements in
connection with such use.
TI products are neither designed nor intended for use in automotive applications or environments unless the specific TI products
are designated by TI as compliant with ISO/TS 16949 requirements. Buyers acknowledge and agree that, if they use any
non-designated products in automotive applications, TI will not be responsible for any failure to meet such requirements.
Following are URLs where you can obtain information on other Texas Instruments products and application solutions:
Products
Applications
Amplifiers
amplifier.ti.com
Audio
www.ti.com/audio
Data Converters
dataconverter.ti.com
Automotive
www.ti.com/automotive
DSP
dsp.ti.com
Broadband
www.ti.com/broadband
Interface
interface.ti.com
Digital Control
www.ti.com/digitalcontrol
Logic
logic.ti.com
Military
www.ti.com/military
Power Mgmt
power.ti.com
Optical Networking
www.ti.com/opticalnetwork
Microcontrollers
microcontroller.ti.com
Security
www.ti.com/security
Low Power
Wireless
www.ti.com/lpw
Telephony
www.ti.com/telephony
Video & Imaging
www.ti.com/video
Wireless
www.ti.com/wireless
Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265
Copyright © 2007, Texas Instruments Incorporated
PACKAGE OPTION ADDENDUM
www.ti.com
23-Apr-2007
PACKAGING INFORMATION
Orderable Device
Status (1)
Package
Type
Package
Drawing
Pins Package Eco Plan (2)
Qty
SN65ALS180D
ACTIVE
SOIC
D
14
50
Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
SN65ALS180DE4
ACTIVE
SOIC
D
14
50
Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
SN65ALS180DG4
ACTIVE
SOIC
D
14
50
Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
SN65ALS180DR
ACTIVE
SOIC
D
14
2500 Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
SN65ALS180DRE4
ACTIVE
SOIC
D
14
2500 Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
SN65ALS180DRG4
ACTIVE
SOIC
D
14
2500 Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
SN65ALS180N
OBSOLETE
PDIP
N
14
TBD
Call TI
SN75ALS180D
ACTIVE
SOIC
D
14
50
Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
SN75ALS180DE4
ACTIVE
SOIC
D
14
50
Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
SN75ALS180DG4
ACTIVE
SOIC
D
14
50
Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
SN75ALS180DR
ACTIVE
SOIC
D
14
2500 Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
SN75ALS180DRE4
ACTIVE
SOIC
D
14
2500 Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
SN75ALS180DRG4
ACTIVE
SOIC
D
14
2500 Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
SN75ALS180N
ACTIVE
PDIP
N
14
25
Pb-Free
(RoHS)
CU NIPDAU
N / A for Pkg Type
SN75ALS180NE4
ACTIVE
PDIP
N
14
25
Pb-Free
(RoHS)
CU NIPDAU
N / A for Pkg Type
Lead/Ball Finish
MSL Peak Temp (3)
Call TI
(1)
The marketing status values are defined as follows:
ACTIVE: Product device recommended for new designs.
LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect.
NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in
a new design.
PREVIEW: Device has been announced but is not in production. Samples may or may not be available.
OBSOLETE: TI has discontinued the production of the device.
(2)
Eco Plan - The planned eco-friendly classification: Pb-Free (RoHS), Pb-Free (RoHS Exempt), or Green (RoHS & no Sb/Br) - please check
http://www.ti.com/productcontent for the latest availability information and additional product content details.
TBD: The Pb-Free/Green conversion plan has not been defined.
Pb-Free (RoHS): TI's terms "Lead-Free" or "Pb-Free" mean semiconductor products that are compatible with the current RoHS requirements
for all 6 substances, including the requirement that lead not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered
at high temperatures, TI Pb-Free products are suitable for use in specified lead-free processes.
Pb-Free (RoHS Exempt): This component has a RoHS exemption for either 1) lead-based flip-chip solder bumps used between the die and
package, or 2) lead-based die adhesive used between the die and leadframe. The component is otherwise considered Pb-Free (RoHS
compatible) as defined above.
Green (RoHS & no Sb/Br): TI defines "Green" to mean Pb-Free (RoHS compatible), and free of Bromine (Br) and Antimony (Sb) based flame
retardants (Br or Sb do not exceed 0.1% by weight in homogeneous material)
(3)
MSL, Peak Temp. -- The Moisture Sensitivity Level rating according to the JEDEC industry standard classifications, and peak solder
temperature.
Addendum-Page 1
PACKAGE OPTION ADDENDUM
www.ti.com
23-Apr-2007
Important Information and Disclaimer:The information provided on this page represents TI's knowledge and belief as of the date that it is
provided. TI bases its knowledge and belief on information provided by third parties, and makes no representation or warranty as to the
accuracy of such information. Efforts are underway to better integrate information from third parties. TI has taken and continues to take
reasonable steps to provide representative and accurate information but may not have conducted destructive testing or chemical analysis on
incoming materials and chemicals. TI and TI suppliers consider certain information to be proprietary, and thus CAS numbers and other limited
information may not be available for release.
In no event shall TI's liability arising out of such information exceed the total purchase price of the TI part(s) at issue in this document sold by TI
to Customer on an annual basis.
Addendum-Page 2
PACKAGE MATERIALS INFORMATION
www.ti.com
19-May-2007
TAPE AND REEL INFORMATION
Pack Materials-Page 1
PACKAGE MATERIALS INFORMATION
www.ti.com
Device
19-May-2007
Package Pins
Site
Reel
Diameter
(mm)
Reel
Width
(mm)
A0 (mm)
B0 (mm)
K0 (mm)
P1
(mm)
W
Pin1
(mm) Quadrant
SN65ALS180DR
D
14
MLA
330
16
6.5
9.0
2.1
8
16
Q1
SN75ALS180DR
D
14
MLA
330
16
6.5
9.0
2.1
8
16
Q1
TAPE AND REEL BOX INFORMATION
Device
Package
Pins
Site
Length (mm)
Width (mm)
Height (mm)
SN65ALS180DR
D
14
MLA
342.9
336.6
28.58
SN75ALS180DR
D
14
MLA
342.9
336.6
28.58
Pack Materials-Page 2
IMPORTANT NOTICE
Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, modifications, enhancements,
improvements, and other changes to its products and services at any time and to discontinue any product or service without notice.
Customers should obtain the latest relevant information before placing orders and should verify that such information is current and
complete. All products are sold subject to TI’s terms and conditions of sale supplied at the time of order acknowledgment.
TI warrants performance of its hardware products to the specifications applicable at the time of sale in accordance with TI’s
standard warranty. Testing and other quality control techniques are used to the extent TI deems necessary to support this
warranty. Except where mandated by government requirements, testing of all parameters of each product is not necessarily
performed.
TI assumes no liability for applications assistance or customer product design. Customers are responsible for their products and
applications using TI components. To minimize the risks associated with customer products and applications, customers should
provide adequate design and operating safeguards.
TI does not warrant or represent that any license, either express or implied, is granted under any TI patent right, copyright, mask
work right, or other TI intellectual property right relating to any combination, machine, or process in which TI products or services
are used. Information published by TI regarding third-party products or services does not constitute a license from TI to use such
products or services or a warranty or endorsement thereof. Use of such information may require a license from a third party under
the patents or other intellectual property of the third party, or a license from TI under the patents or other intellectual property of TI.
Reproduction of information in TI data books or data sheets is permissible only if reproduction is without alteration and is
accompanied by all associated warranties, conditions, limitations, and notices. Reproduction of this information with alteration is an
unfair and deceptive business practice. TI is not responsible or liable for such altered documentation.
Resale of TI products or services with statements different from or beyond the parameters stated by TI for that product or service
voids all express and any implied warranties for the associated TI product or service and is an unfair and deceptive business
practice. TI is not responsible or liable for any such statements.
TI products are not authorized for use in safety-critical applications (such as life support) where a failure of the TI product would
reasonably be expected to cause severe personal injury or death, unless officers of the parties have executed an agreement
specifically governing such use. Buyers represent that they have all necessary expertise in the safety and regulatory ramifications
of their applications, and acknowledge and agree that they are solely responsible for all legal, regulatory and safety-related
requirements concerning their products and any use of TI products in such safety-critical applications, notwithstanding any
applications-related information or support that may be provided by TI. Further, Buyers must fully indemnify TI and its
representatives against any damages arising out of the use of TI products in such safety-critical applications.
TI products are neither designed nor intended for use in military/aerospace applications or environments unless the TI products are
specifically designated by TI as military-grade or "enhanced plastic." Only products designated by TI as military-grade meet military
specifications. Buyers acknowledge and agree that any such use of TI products which TI has not designated as military-grade is
solely at the Buyer's risk, and that they are solely responsible for compliance with all legal and regulatory requirements in
connection with such use.
TI products are neither designed nor intended for use in automotive applications or environments unless the specific TI products
are designated by TI as compliant with ISO/TS 16949 requirements. Buyers acknowledge and agree that, if they use any
non-designated products in automotive applications, TI will not be responsible for any failure to meet such requirements.
Following are URLs where you can obtain information on other Texas Instruments products and application solutions:
Products
Applications
Amplifiers
amplifier.ti.com
Audio
www.ti.com/audio
Data Converters
dataconverter.ti.com
Automotive
www.ti.com/automotive
DSP
dsp.ti.com
Broadband
www.ti.com/broadband
Interface
interface.ti.com
Digital Control
www.ti.com/digitalcontrol
Logic
logic.ti.com
Military
www.ti.com/military
Power Mgmt
power.ti.com
Optical Networking
www.ti.com/opticalnetwork
Microcontrollers
microcontroller.ti.com
Security
www.ti.com/security
RFID
www.ti-rfid.com
Telephony
www.ti.com/telephony
Low Power
Wireless
www.ti.com/lpw
Video & Imaging
www.ti.com/video
Wireless
www.ti.com/wireless
Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265
Copyright © 2007, Texas Instruments Incorporated