TI SN75179BD

SN75179B
DIFFERENTIAL DRIVER AND RECEIVER PAIR
SLLS003E – OCTOBER 1985 – REVISED JUNE 1998
D
D
D
D
D
D
D
D
D
D
D OR P PACKAGE
(TOP VIEW)
Meets or Exceeds the Requirements of
TIA/EIA-422-B, TIA/EIA-485-A, and ITU
Recommendation V.11
Bus Voltage Range . . . – 7 V to 12 V
Positive- and Negative-Current Limiting
Driver Output Capability . . . 60 mA Max
Driver Thermal-Shutdown Protection
Receiver Input Impedance . . . 12 kΩ Min
Receiver Input Sensitivity . . . ± 200 mV
Receiver Input Hysteresis . . . 50 mV Typ
Operates From Single 5-V Supply
Low Power Requirements
VCC
R
D
GND
1
8
2
7
3
6
4
5
A
B
Z
Y
description
The SN75179B is a differential driver and receiver pair designed for balanced transmission-line applications
and meets TIA/EIA-422-B, TIA/EIA-485-A, and ITU Recommendation V.11. It is designed to improve the
performance of full-duplex data communications over long bus lines.
The SN75179B driver output provides limiting for both positive and negative currents. The receiver features high
input impedance, input hysteresis for increased noise immunity, and input sensitivity of ± 200 mV over a
common-mode input voltage range of – 7 V to 12 V. The driver provides thermal shutdown for protection from
line fault conditions. Thermal shutdown is designed to occur at a junction temperature of approximately 150°C.
The SN75179B is designed to drive current loads of up to 60 mA maximum.
The SN75179B is characterized for operation from 0°C to 70°C.
Function Tables
DRIVER
INPUT
D
OUTPUTS
Y
Z
H
H
L
L
L
H
RECEIVER
DIFFERENTIAL INPUTS
A–B
OUTPUT
R
VID ≥ 0.2 V
– 0.2 V < VID < 0.2 V
H
VID ≤ – 0.2 V
L
Open
?
?
H = high level, L = low level, ? = indeterminate
Please be aware that an important notice concerning availability, standard warranty, and use in critical applications of
Texas Instruments semiconductor products and disclaimers thereto appears at the end of this data sheet.
Copyright  1998, Texas Instruments Incorporated
PRODUCTION DATA information is current as of publication date.
Products conform to specifications per the terms of Texas Instruments
standard warranty. Production processing does not necessarily include
testing of all parameters.
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
1
SN75179B
DIFFERENTIAL DRIVER AND RECEIVER PAIR
SLLS003E – OCTOBER 1985 – REVISED JUNE 1998
logic symbol†
logic diagram (positive logic)
8
2
7
R
6
3
5
D
8
A
B
R
2
7
A
B
Z
6
Y
D
3
5
† This symbol is in accordance with ANSI/IEEE Std 91-1984
and IEC Publication 617-12.
Z
Y
schematics of inputs and outputs
EQUIVALENT OF DRIVER INPUT
TYPICAL OF ALL DRIVER OUTPUTS
VCC
VCC
Input
Output
GND
Driver input: R(eq) = 3 kΩ NOM
R(eq) = equivalent resistor
EQUIVALENT OF EACH RECEIVER INPUT
TYPICAL OF ALL RECEIVER OUTPUTS
VCC
VCC
85 Ω
NOM
960 Ω
NOM
Input
16.8 kΩ
NOM
2
960 Ω
NOM
Output
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
SN75179B
DIFFERENTIAL DRIVER AND RECEIVER PAIR
SLLS003E – OCTOBER 1985 – REVISED JUNE 1998
absolute maximum ratings over operating free-air temperature range (unless otherwise noted)†
Supply voltage, VCC (see Note 1) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 V
Voltage range at any bus terminal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . – 10 V to 15 V
Differential input voltage, VID (see Note 2) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ± 25 V
Package thermal impedance, θJA (see Note 3): D package . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 197°C/W
P package . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 104°C/W
Storage temperature range, Tstg . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . – 65°C to 150°C
Lead temperature 1,6 mm (1/16 inch) from case for 10 seconds . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 260°C
† Stresses beyond those listed under “absolute maximum ratings” may cause permanent damage to the device. These are stress ratings only, and
functional operation of the device at these or any other conditions beyond those indicated under “recommended operating conditions” is not
implied. Exposure to absolute-maximum-rated conditions for extended periods may affect device reliability.
NOTES: 1. All voltage values, except differential input voltage, are with respect to network ground terminal.
2. Differential input voltage is measured at the noninverting input with respect to the corresponding inverting input.
3. The package thermal impedance is calculated in accordance with JESD 51, except for through-hole packages, which use a trace
length of zero.
recommended operating conditions
Supply voltage, VCC
High-level input voltage, VIH
Driver
Low-level input voltage, VIL
Driver
MAX
UNIT
5
5.25
V
–7‡
Differential input voltage, VID
Low level output current,
Low-level
current IOL
NOM
2
Common-mode input voltage, VIC
High level output current,
High-level
current IOH
MIN
4.75
Driver
Receiver
Driver
V
0.8
V
12
V
± 12
V
– 60
mA
– 400
µA
60
Receiver
8
mA
Operating free-air temperature, TA
0
70
°C
‡ The algebraic convention, where the less positive (more negative) limit is designated minimum, is used in this data sheet for common-mode input
voltage and threshold voltage.
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
3
SN75179B
DIFFERENTIAL DRIVER AND RECEIVER PAIR
SLLS003E – OCTOBER 1985 – REVISED JUNE 1998
DRIVER SECTION
electrical characteristics over recommended ranges of supply voltage and operating free-air
temperature (unless otherwise noted)
PARAMETER
TEST CONDITIONS
VIK
Input clamp voltage
II = - 18 mA
VO
VOD1 
Output voltage
IO = 0
Differential output voltage
IO = 0
VOD2 
g
Differential output voltage
VOD3 
Differential output voltage
∆VOD 
Change in magnitude of common-mode
output voltage§
VOC
Common-mode output voltage
∆VOC 
Change in magnitude of common-mode
output voltage§
IO
IIH
Output current
IIL
Low-level input current
IOS
MIN
V
6
V
1.5
6
V
See Figure 1
RL = 54 Ω,
See Figure 1
1.5
V
2.5
1.5
VCC = 0,
VI = 2.4 V
High-level input current
See Figure 1
VO = – 7 V to 12 V
VI = 0.4 V
VO = – 7 V
Short circuit output current
Short-circuit
UNIT
– 1.5
RL = 100 Ω,
RL = 54 Ω or 100 Ω,
MAX
0
1/2VOD1
or 2‡
See Note 4
TYP†
5
V
5
V
± 0.2
V
3
–1
V
± 0.2
V
± 100
µA
20
µA
– 200
µA
– 250
VO = VCC or 12 V
No load
250
mA
ICC
Supply current (total package)
57
70
mA
† All typical values are at VCC = 5 V and TA = 25°C.
‡ The minimum VOD2 with 100-Ω load is either 1/2 VOD2 or 2 V, whichever is greater.
§ ∆|VOD| and ∆|VOC| are the changes in magnitude of VOD and VOC, respectively, that occur when the input changes from a high level to a low
level.
NOTE 4: See TIA/EIA-485-A, Figure 3.5, Test Termination Measurement 2.
switching characteristics, VCC = 5 V, TA = 25°C
PARAMETER
td(OD)
tt(OD)
TEST CONDITIONS
Differential output delay time
RL = 54 Ω
Ω,
Differential output transition time
MIN
TYP
MAX
15
22
ns
20
30
ns
See Figure 3
Symbol Equivalents
DATA-SHEET PARAMETER
TIA/EIA-422-B
VO
| VOD1 |
Voa, Vob
Vo
Voa, Vob
Vo
| VOD2 |
Vt (RL = 100 Ω)
Vt (RL = 54 Ω)
Vt (Test Termination Measurement 2)
∆ | VOD |
| | Vt | – |Vt | |
| | Vt | – |Vt | |
VOC
∆ | VOC |
| Vos |
| Vos |
| Vos – Vos |
| Vos – Vos |
IOS
IO
| Isa |, | Isb |
| VOD3 |
4
TIA/EIA-485-A
| Ixa |, | Ixb |
POST OFFICE BOX 655303
Iia , Iib
• DALLAS, TEXAS 75265
UNIT
SN75179B
DIFFERENTIAL DRIVER AND RECEIVER PAIR
SLLS003E – OCTOBER 1985 – REVISED JUNE 1998
RECEIVER SECTION
electrical characteristics over recommended ranges of common-mode input voltage, supply
voltage, and operating free-air temperature (unless otherwise noted)
PARAMETER
TEST CONDITIONS
VIT +
VIT –
Positive-going input threshold voltage
Vhys
VOH
Hysteresis voltage (VIT + – VIT –)
VOL
Low-level output voltage
Negative-going input threshold voltage
High-level output voltage
II
Line input current
ri
Input resistance
VO = 2.7 V,
VO = 0.5 V,
MIN
IO = – 0.4 mA
IO = 8 mA
TYP†
MAX
0.2
– 0.2‡
IOH = – 400 µA,
IOL = 8 mA,
Other input at 0 V
V,
See Figure 2
mV
2.7
V
See Figure 2
0.45
VI = 12 V
VI = – 7 V
See Note 5
V
V
50
VID = 200 mV,
VID = – 200 mV,
UNIT
1
– 0.8
12
V
mA
kΩ
IOS
Short-circuit output current
– 15
– 85
mA
ICC
Supply current (total package)
No load
57
70
mA
† All typical values are at VCC = 5 V, TA = 25°C.
‡ The algebraic convention, where the less positive (more negative) limit is designated minimum, is used in this data sheet for common-mode input
voltage and threshold voltage levels only.
NOTE 5: Refer to TIA/EIA-422-B for exact conditions.
switching characteristics, VCC = 5 V, TA = 25°C
PARAMETER
tPLH
tPHL
TEST CONDITIONS
Propagation delay time, low- to high-level output
VID = – 1.5 V to 1.5 V,
CL = 15 pF,
See Figure 4
Propagation delay time, high- to low-level output
MIN
TYP
MAX
19
35
UNIT
ns
30
40
ns
PARAMETER MEASUREMENT INFORMATION
RL
2
VOD2
RL
2
VOC
Figure 1. Driver VDD and VOC
VID
VOL
VOH
+ IOL
– IOH
Figure 2. Receiver VOH and VOL
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
5
SN75179B
DIFFERENTIAL DRIVER AND RECEIVER PAIR
SLLS003E – OCTOBER 1985 – REVISED JUNE 1998
PARAMETER MEASUREMENT INFORMATION (CONTINUED)
3V
Input
RL = 54 Ω
Generator
(see Note A)
50 Ω
CL = 50 pF
(see Note B)
Output
1.5 V
1.5 V
0V
td(OD)
Output
td(OD)
90%
10%
50%
≈ 2.5 V
50%
≈ – 2.5 V
tt(OD)
tt(OD)
TEST CIRCUIT
VOLTAGE WAVEFORMS
NOTES: A. The input pulse is supplied by a generator having the following characteristics: PRR ≤ 1 MHz, 50% duty cycle, tr ≤ 6 ns,
tf ≤ 6 ns, ZO = 50 Ω.
B. CL includes probe and jig capacitance.
Figure 3. Driver Test Circuit and Voltage Waveforms
Input
Generator
(see Note A)
50 Ω
3V
1.5 V
1.5 V
0V
Output
1.5 V
CL = 50 pF
(see Note B)
tPLH
tPHL
VOH
Output
1.3 V
1.3 V
VOL
TEST CIRCUIT
VOLTAGE WAVEFORMS
NOTES: A. The input pulse is supplied by a generator having the following characteristics: PRR ≤ 1 MHz, 50% duty cycle, tr ≤ 6 ns,
tf ≤ 6 ns, ZO = 50 Ω.
B. CL includes probe and jig capacitance.
Figure 4. Receiver Test Circuit and Voltage Waveforms
6
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
SN75179B
DIFFERENTIAL DRIVER AND RECEIVER PAIR
SLLS003E – OCTOBER 1985 – REVISED JUNE 1998
TYPICAL CHARACTERISTICS
DRIVER
DRIVER
HIGH-LEVEL OUTPUT VOLTAGE
vs
HIGH-LEVEL OUTPUT CURRENT
LOW-LEVEL OUTPUT VOLTAGE
vs
LOW-LEVEL OUTPUT CURRENT
5
VCC = 5 V
TA = 25°C
4.5
VCC = 5 V
TA = 25°C
4.5
VOL – Low-Level Output Voltage – V
VOH – High-Level Output Voltage – V
5
4
3.5
3
2.5
2
1.5
1
4
3.5
3
2.5
2
1.5
1
0.5
0.5
0
0
0
– 20
– 40
– 60
– 80
– 100
0
– 120
IOH – High-Level Output Current – mA
80
100
20
40
60
IOL – Low-Level Output Current – mA
Figure 5
Figure 6
DRIVER
RECEIVER
DIFFERENTIAL OUTPUT VOLTAGE
vs
OUTPUT CURRENT
OUTPUT VOLTAGE
vs
DIFFERENTIAL INPUT VOLTAGE
4
5
VCC = 5 V
TA = 25°C
3.5
4.5
VCC = 5 V
IO = 0
TA = 25°C
4
3
VO – Output Voltage – V
VOD – Differential Output Voltage – V
120
2.5
2
1.5
3.5
VIC =
–12 V
VIC =
0
VIT–
VIT–
VIC =
12 V
3
VIT–
2.5
2
VIT+
VIT+
VIT+
1.5
1
1
0.5
0
0.5
0
10
20
30 40 50 60 70 80
IO – Output Current – mA
90
100
0
–125 –100 –75 – 50 – 25 0
25 50 75 100 125
VID – Differential Input Voltage – mV
Figure 8
Figure 7
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
7
SN75179B
DIFFERENTIAL DRIVER AND RECEIVER PAIR
SLLS003E – OCTOBER 1985 – REVISED JUNE 1998
TYPICAL CHARACTERISTICS
HIGH-LEVEL OUTPUT VOLTAGE
vs
FREE-AIR TEMPERATURE
HIGH-LEVEL OUTPUT VOLTAGE
vs
HIGH-LEVEL OUTPUT CURRENT
5
5
VID = 0.2 V
TA = 25°C
4
3.5
3
VCC = 5.25 V
2.5
VCC = 5 V
2
1.5
1
VCC = 5 V
VID = 0.2 V
IOH = – 440 µA
4.5
VOH – High-Level Output Voltage – V
VOH – High-Level Output Voltage – V
4.5
VCC = 4.75 V
4
3.5
3
2.5
2
1.5
1
0.5
0.5
0
0
0
0
– 5 – 10 – 15 – 20 – 25 – 30 – 35 – 40 – 45 – 50
IOH – High-Level Output Current – mA
70
20
30 40
50
60
TA – Free-Air Temperature – °C
10
Figure 9
RECEIVER
RECEIVER
LOW-LEVEL OUTPUT VOLTAGE
vs
FREE-AIR TEMPERATURE
0.5
VCC = 5 V
TA = 25°C
VOL – Low-Level Output Voltage – V
VOL– Low-Level Output Voltage - V
0.6
0.4
0.3
0.2
0.1
0
0
5
10
15
20
25
30
IOL – Low-Level Output Current – mA
VCC = 5 V
VID = – 0.2 V
IOL = 8 mA
0.4
0.3
0.2
0.1
0
0
10
20
30
40
50
Figure 12
POST OFFICE BOX 655303
60
70
TA – Free-Air Temperature – °C
Figure 11
8
90
Figure 10
LOW-LEVEL OUTPUT VOLTAGE
vs
LOW-LEVEL OUTPUT CURRENT
0.5
80
• DALLAS, TEXAS 75265
80
90
PACKAGE OPTION ADDENDUM
www.ti.com
4-Jun-2007
PACKAGING INFORMATION
Orderable Device
Status (1)
Package
Type
Package
Drawing
Pins Package Eco Plan (2)
Qty
SN75179BD
ACTIVE
SOIC
D
8
75
Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
SN75179BDE4
ACTIVE
SOIC
D
8
75
Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
SN75179BDG4
ACTIVE
SOIC
D
8
75
Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
SN75179BDR
ACTIVE
SOIC
D
8
2500 Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
SN75179BDRE4
ACTIVE
SOIC
D
8
2500 Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
SN75179BDRG4
ACTIVE
SOIC
D
8
2500 Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
SN75179BP
ACTIVE
PDIP
P
8
50
Pb-Free
(RoHS)
CU NIPDAU
N / A for Pkg Type
SN75179BPE4
ACTIVE
PDIP
P
8
50
Pb-Free
(RoHS)
CU NIPDAU
N / A for Pkg Type
SN75179BPSR
ACTIVE
SO
PS
8
2000 Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
SN75179BPSRE4
ACTIVE
SO
PS
8
2000 Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
SN75179BPSRG4
ACTIVE
SO
PS
8
2000 Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
Lead/Ball Finish
MSL Peak Temp (3)
(1)
The marketing status values are defined as follows:
ACTIVE: Product device recommended for new designs.
LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect.
NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in
a new design.
PREVIEW: Device has been announced but is not in production. Samples may or may not be available.
OBSOLETE: TI has discontinued the production of the device.
(2)
Eco Plan - The planned eco-friendly classification: Pb-Free (RoHS), Pb-Free (RoHS Exempt), or Green (RoHS & no Sb/Br) - please check
http://www.ti.com/productcontent for the latest availability information and additional product content details.
TBD: The Pb-Free/Green conversion plan has not been defined.
Pb-Free (RoHS): TI's terms "Lead-Free" or "Pb-Free" mean semiconductor products that are compatible with the current RoHS requirements
for all 6 substances, including the requirement that lead not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered
at high temperatures, TI Pb-Free products are suitable for use in specified lead-free processes.
Pb-Free (RoHS Exempt): This component has a RoHS exemption for either 1) lead-based flip-chip solder bumps used between the die and
package, or 2) lead-based die adhesive used between the die and leadframe. The component is otherwise considered Pb-Free (RoHS
compatible) as defined above.
Green (RoHS & no Sb/Br): TI defines "Green" to mean Pb-Free (RoHS compatible), and free of Bromine (Br) and Antimony (Sb) based flame
retardants (Br or Sb do not exceed 0.1% by weight in homogeneous material)
(3)
MSL, Peak Temp. -- The Moisture Sensitivity Level rating according to the JEDEC industry standard classifications, and peak solder
temperature.
Important Information and Disclaimer:The information provided on this page represents TI's knowledge and belief as of the date that it is
provided. TI bases its knowledge and belief on information provided by third parties, and makes no representation or warranty as to the
accuracy of such information. Efforts are underway to better integrate information from third parties. TI has taken and continues to take
reasonable steps to provide representative and accurate information but may not have conducted destructive testing or chemical analysis on
incoming materials and chemicals. TI and TI suppliers consider certain information to be proprietary, and thus CAS numbers and other limited
information may not be available for release.
In no event shall TI's liability arising out of such information exceed the total purchase price of the TI part(s) at issue in this document sold by TI
Addendum-Page 1
PACKAGE OPTION ADDENDUM
www.ti.com
4-Jun-2007
to Customer on an annual basis.
Addendum-Page 2
PACKAGE MATERIALS INFORMATION
www.ti.com
14-Jul-2012
TAPE AND REEL INFORMATION
*All dimensions are nominal
Device
Package Package Pins
Type Drawing
SPQ
Reel
Reel
A0
Diameter Width (mm)
(mm) W1 (mm)
B0
(mm)
K0
(mm)
P1
(mm)
W
Pin1
(mm) Quadrant
SN75179BDR
SOIC
D
8
2500
330.0
12.4
6.4
5.2
2.1
8.0
12.0
Q1
SN75179BPSR
SO
PS
8
2000
330.0
16.4
8.2
6.6
2.5
12.0
16.0
Q1
Pack Materials-Page 1
PACKAGE MATERIALS INFORMATION
www.ti.com
14-Jul-2012
*All dimensions are nominal
Device
Package Type
Package Drawing
Pins
SPQ
Length (mm)
Width (mm)
Height (mm)
SN75179BDR
SN75179BPSR
SOIC
D
8
2500
340.5
338.1
20.6
SO
PS
8
2000
367.0
367.0
38.0
Pack Materials-Page 2
IMPORTANT NOTICE
Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, enhancements, improvements and other
changes to its semiconductor products and services per JESD46, latest issue, and to discontinue any product or service per JESD48, latest
issue. Buyers should obtain the latest relevant information before placing orders and should verify that such information is current and
complete. All semiconductor products (also referred to herein as “components”) are sold subject to TI’s terms and conditions of sale
supplied at the time of order acknowledgment.
TI warrants performance of its components to the specifications applicable at the time of sale, in accordance with the warranty in TI’s terms
and conditions of sale of semiconductor products. Testing and other quality control techniques are used to the extent TI deems necessary
to support this warranty. Except where mandated by applicable law, testing of all parameters of each component is not necessarily
performed.
TI assumes no liability for applications assistance or the design of Buyers’ products. Buyers are responsible for their products and
applications using TI components. To minimize the risks associated with Buyers’ products and applications, Buyers should provide
adequate design and operating safeguards.
TI does not warrant or represent that any license, either express or implied, is granted under any patent right, copyright, mask work right, or
other intellectual property right relating to any combination, machine, or process in which TI components or services are used. Information
published by TI regarding third-party products or services does not constitute a license to use such products or services or a warranty or
endorsement thereof. Use of such information may require a license from a third party under the patents or other intellectual property of the
third party, or a license from TI under the patents or other intellectual property of TI.
Reproduction of significant portions of TI information in TI data books or data sheets is permissible only if reproduction is without alteration
and is accompanied by all associated warranties, conditions, limitations, and notices. TI is not responsible or liable for such altered
documentation. Information of third parties may be subject to additional restrictions.
Resale of TI components or services with statements different from or beyond the parameters stated by TI for that component or service
voids all express and any implied warranties for the associated TI component or service and is an unfair and deceptive business practice.
TI is not responsible or liable for any such statements.
Buyer acknowledges and agrees that it is solely responsible for compliance with all legal, regulatory and safety-related requirements
concerning its products, and any use of TI components in its applications, notwithstanding any applications-related information or support
that may be provided by TI. Buyer represents and agrees that it has all the necessary expertise to create and implement safeguards which
anticipate dangerous consequences of failures, monitor failures and their consequences, lessen the likelihood of failures that might cause
harm and take appropriate remedial actions. Buyer will fully indemnify TI and its representatives against any damages arising out of the use
of any TI components in safety-critical applications.
In some cases, TI components may be promoted specifically to facilitate safety-related applications. With such components, TI’s goal is to
help enable customers to design and create their own end-product solutions that meet applicable functional safety standards and
requirements. Nonetheless, such components are subject to these terms.
No TI components are authorized for use in FDA Class III (or similar life-critical medical equipment) unless authorized officers of the parties
have executed a special agreement specifically governing such use.
Only those TI components which TI has specifically designated as military grade or “enhanced plastic” are designed and intended for use in
military/aerospace applications or environments. Buyer acknowledges and agrees that any military or aerospace use of TI components
which have not been so designated is solely at the Buyer's risk, and that Buyer is solely responsible for compliance with all legal and
regulatory requirements in connection with such use.
TI has specifically designated certain components which meet ISO/TS16949 requirements, mainly for automotive use. Components which
have not been so designated are neither designed nor intended for automotive use; and TI will not be responsible for any failure of such
components to meet such requirements.
Products
Applications
Audio
www.ti.com/audio
Automotive and Transportation
www.ti.com/automotive
Amplifiers
amplifier.ti.com
Communications and Telecom
www.ti.com/communications
Data Converters
dataconverter.ti.com
Computers and Peripherals
www.ti.com/computers
DLP® Products
www.dlp.com
Consumer Electronics
www.ti.com/consumer-apps
DSP
dsp.ti.com
Energy and Lighting
www.ti.com/energy
Clocks and Timers
www.ti.com/clocks
Industrial
www.ti.com/industrial
Interface
interface.ti.com
Medical
www.ti.com/medical
Logic
logic.ti.com
Security
www.ti.com/security
Power Mgmt
power.ti.com
Space, Avionics and Defense
www.ti.com/space-avionics-defense
Microcontrollers
microcontroller.ti.com
Video and Imaging
www.ti.com/video
RFID
www.ti-rfid.com
OMAP Applications Processors
www.ti.com/omap
TI E2E Community
e2e.ti.com
Wireless Connectivity
www.ti.com/wirelessconnectivity
Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265
Copyright © 2012, Texas Instruments Incorporated