SEMTECH SC908

SC908
Power Management IC for
Single-Cell Li-Ion Devices
POWER MANAGEMENT
Features
Description
„
The SC908 is a complete power management system
designed for use in Bluetooth wireless headsets, portable
media players, and other battery-powered electronics
where size is critical. Included are a full featured standalone Li-Ion battery charger with a programmable
low-battery monitor, a low noise LDO regulator, and a DCDC buck converter.
„
„
„
„
„
„
„
„
„
„
„
„
„
Single Cell Li-Ion battery charger — CC/CV charging
with current soft start
Charger regulated output voltage — 4.2V ±1% over
temperature with Kelvin sense of battery voltage
Charger input protection withstands 28V indefinitely
Charger max constant current setting — 500mA
Adjustable charge termination current down to
10mA
Battery NTC interface disables charging if battery
temperature out of range
Programmable low battery detector threshold
Four status indicators
Programmable charge completion timer
Buck converter with enable — output programmable
from 1V to 3V, 150mA max output
Buck converter efficiency — 88% at 50mA
General purpose low noise LDO regulator with fast
enable, active shutdown
4x4x0.9 (mm) MLPQ package
WEEE and RoHS compliant
Battery charging features include programmable precharge, fast-charge, and termination current settings.
Charge termination is controlled by a programmable
timer and by a resistor that sets the termination current.
The 28V max input voltage protects against hotplug overshoot and faulty adapters without additional protection
circuitry. The battery voltage Kelvin sense input eliminates errors due to high charging currents. A battery
thermistor interface disables charging when the battery
temperature exceeds safe-to-charge limits.
The step-down switching regulator (buck converter)
improves system efficiency and extends battery life. The
LDO regulator can be powered directly from the battery
or from the buck converter output when efficiency is critical. The fast-starting low noise LDO regulator is suitable
for audio, RF, or general purpose regulation required by
peripheral devices, such as a vibrating alert motor. The
low battery detector warns when the battery level is
below 3.3V, and when the battery has discharged below
a lower programmable voltage limit.
Applications
„
Bluetooth headsets
MP3 players
„ Low cost mobile phones
„
Typical Application Circuit
Charging Adapter
VAD
VSYS
CVAD
BAT
BSEN
CVSYS
RRTIME
RTIME
CBAT
RITERM
RNPU
ITERM
Can supply LDO
from battery or from
DC-DC converter
RIPRGM
IPRGM
Charging
RNTC (Battery
Pack NTC
Thermistor)
Charger
Present
RRLBAT
EN_NTC
CVREF
SC908
CHRGB
CPB
FLTB
LBATB
RLBAT
VREF
AGND
DGND
LEN
LVIN
CLVIN
LVOUT
LFB
SEN
Li-Ion
BATTERY
To Audio Circuits
or vibrator motor
RL1
LS
SLX
RS1
SFB
PGND
CLVOUT
SVOUT,
To Bluetooth
Processor
CSFB
CSVOUT
RL2
CSFG
RS2
US Patent: 6,836,095
January 24, 2008
© 2008 Semtech Corporation
1
SC908
EN_NTC
BAT
SLX
PGND
CHRGB
Ordering Information
BSEN
Pin Configuration
24
23
22
21
20
19
18
SEN
17
CPB
VAD
1
VSYS
2
IPRGM
3
16
LBATB
ITERM
4
15
FLTB
RTIME
5
14
SFB
RLBAT
6
13
LEN
TOP VIEW
9
10
11
12
VREF
AGND
DGND
LVOUT
8
LVIN
7
LFB
T
Device
Package
SC908MLTRT(1,2)
MLPQ-24
SC908EVB
Evaluation Board
Notes:
(1) Available in tape and reel only. A reel contains 3,000 devices.
(2) Lead-free package only. Device is WEEE and RoHS compliant.
MLP-24; 4x4, 24 LEAD
θJA = 29°C/W
Marking Information
SC908
yyww
xxxxx
xxxxx
yy = year of manufacture
ww = week of manufacture
xxxx = lot number
2
SC908
Absolute Maximum Ratings(1)
Recommended Operating Conditions
VAD (V) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . -0.3 to +28.0
Ambient Temperature Range (°C) . . . . . . . . . . . . . -40 to +85
BAT, VSYS, CHRGB, FLTB, LBATB (V) . . . . . . . . . . -0.3 to +5.5
Charger Input Voltage Range (V) . . . . . . . . . . . . 4.45 to 7.05
(2)
SRC
+ 0.3
LDO Regulator Input Voltage Range (V) . . . . . . . . 2.2 to VBAT
SLX, LVIN, LEN, SEN (V) . . . . . . . . . . . . . . . . . . . . . . . VBAT + 0.3
Switching Regulator Input Voltage (V) . . . . . . . . . . . . . . . VBAT
CPB (V) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . -0.3 to V
LVOUT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . VLVIN + 0.3
AGND . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . -0.3 to +0.3
PGND . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . -1.0 to +0.3
Pin Voltage — All Other Pins (V) . . . . . . . . . . . . -0.3 to +6.5
Thermal Information
BAT Output Current (A) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
Thermal Resistance, Junction to Ambient (°C/W)(6) . . . . . 29
BAT Short Circuit Duration (s) . . . . . . . . . . . . . . . .Continuous
Junction Temperature Range (°C) . . . . . . . . . . . . .-40 to +150
DC-DC Converter Output Current (mA)(3) . . . . . . -265, +180
Storage Temperature Range (°C) . . . . . . . . . . . . -65 to +150
DC-DC Converter Output Current (mA)(4) . . . . . . . . . . . ±600
IR Reflow Temperature (°C) . . . . . . . . . . . . . . . . . . . . . . . . +260
Total Power Dissipation (W) . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
ESD Protection Level (kV) (5) . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
Exceeding the above specifications may result in permanent damage to the device or device malfunction. Operation outside of the parameters
specified in the Electrical Characteristics section is not recommended.
NOTES:
(1) All absolute maximum ratings are with respect to DGND unless otherwise noted.
(2) VSRC = larger of VBAT and VVSYS
(3) Continuous
(4) Peak
(5) Tested according to JEDEC standard JESD22-A114-B.
(6) Calculated from package in still air, mounted to 3 x 4.5 (in), 4 layer FR4 PCB with thermal vias under the exposed pad per JESD51 standards.
Electrical Characteristics
Test Conditions: VVAD = 4.75V to 5.25 V; VBAT = 3.7V; VLEN = VVAD; Typ values at 25°C; Min and Max at -40°C < TA < 85°C, unless specified.
Parameter
Symbol
Conditions
Min
Typ
Max
Units
VADOP(1)
Operating Voltage
4.45
5
7.05
V
VADUVLO-R
UVLO Rising Threshold
4.05
4.25
4.45
V
VADUVLO-F
UVLO Falling Threshold
3.8
4
4.2
V
VADUVLO-H
UVLO Hysteresis
(VADUVLO-R - VADUVLO-F)
150
VADOVP-R
OVP Rising Threshold
VADOVP-F
OVP Falling Threshold
7.05
VADOVP-H
OVP Hysteresis
(VADOVP-R - VADOVP-F)
50
lleakBAT
VVAD=VSEN=VLEN=0V, VBAT=4.2V
Charger
VAD Input Voltage
Battery Leakage Current (2)
mV
7.5
7.80
7.3
V
V
mV
0.1
2
μA
3
SC908
Electrical Characteristics (continued)
Parameter
Symbol
Conditions
Min
Typ
Max
Units
VADICCQ
VEN_NTC = 0.5 × VVSYS, ICPB = ICHRGB = IFLTB =
ILBATB = IITERM = IIPRGM = 0mA, VSEN = VLEN = 0V
VCV
Measured at BSEN pin
20mA < IBAT < 500mA
0°C < TJ < 125°C
4.16
4.2
4.24
V
Precharge Threshold (Rising)
VTPreQ
Measured at BSEN pin
2.7
2.8
2.9
V
Recharge Threshold (Falling)
VTReQ
VCV - VBSEN
65
113
160
mV
VSYS output voltage (3)
VVSYS
VVAD ≥ 5V, IVSYS ≤ 5mA
VSYS output current
IVSYS
ITERM Programming Resistor
RITERM
Nominal 1%-tol Standard Value
2.67
IBAT Pre-Charge Current
IPreQ
RITERM = 4.99kΩ to GND
27
IBAT Termination Current
ITERM
RITERM = 4.99kΩ to GND
27
IPRGM Programming Resistor
RIPRGM
Nominal 1%-tol Standard Value
2.15
IBAT Fast-Charge Current
IFQ
RIPRGM = 6.04kΩ, VBAT = 3.7V
167
VAD - BAT Dropout Voltage
VDO
IBAT = 500mA, 0°C ≤ TJ ≤ 85°C
IPRGM Regulated Voltage
VIPRGM
RIPRGM = 6.04kΩ to GND
1.45
ITERM Regulated Voltage
VITERM
RITERM = 4.99kΩ to GND
RTIME Regulated Voltage
VRTIME
Precharge Fault Time-Out
tPreQF
Charger (continued)
Charging Adapter
Operating Current
CV Regulation Voltage
1.5
mA
4.7
V
5
mA
17.4
kΩ
39
52
mA
39
52
mA
15.0
kΩ
179
mA
0.8
V
1.5
1.55
V
1.45
1.5
1.55
V
RRTIME = 37.4kΩ to GND
1.475
1.56
1.625
V
RRTIME = 37.4kΩ to GND
38
47
57
mins
RRTIME connected to VSYS
32
42
53
mins
RRTIME = 37.4kΩ to GND
2.50
3.10
3.70
hrs
RRTIME connected to VSYS
2.10
2.67
3.50
hrs
VTNTC_DIS
Charger Disable/Reset (Falling)
9
10
11.5
%VVSYS
VTNTC_HF
NTC Hot (Falling)
27.5
30
31.5
%VVSYS
VTNTC_CR
NTC Cold (Rising)
74
75
76.5
%VVSYS
EN_NTC Hysteresis
VTNTC_HYS
VVAD = 5V
EN_NTC Disable/Reset Hold
Time
tNTC_DIS_H
Momentary disable resets charger
Charger Over-Temperature Shutdown Temperature (Rising)
TCHRGR_OT
Hysteresis = 10°C typical
Charge Complete Time-Out
EN_NTC Thresholds
173
tQComp
45
500
mV
ns
145
°C
4
SC908
Electrical Characteristics (continued)
Parameter
Symbol
Conditions
Core Circuits Quiescent
Current (4)
IQ-Core
VVAD = VSEN = 0V,
VLEN = VBAT = 4.2V
VREF Reference Voltage
VVREF
Min
Typ
Max
Units
Core Functions (Excluding Charger)
100
μA
0.75
V
PSRRREF
VBAT = 3.7V with 0.5VP-to-P ripple,
f ≤ 10kHz, CVREF = 10nF
70
dB
tSU_REF
Delay from first of SEN high
LEN high, VBAT = 3.7V
CVREF = 10nF
VREF from 0V to 95% of final
0.4
ms
Buck Converter Input Voltage
VSVIN
BAT pin is also the switching regulator
supply input
VBAT
V
Buck Converter Under-Voltage
Lockout Rising Threshold
VTSUVLO-R
Buck Converter Under-Voltage
Lockout Falling Threshold
VTSUVLO-F
Buck Converter Under-Voltage
Lockout Hysteresis
VTSUVLO-HYS
VREF Power Supply Rejection
VREF Reference Voltage Start-Up
Time (5, 10)
DC-DC Buck Converter
Buck Converter Quiescent
Current (2)
IBAT-Q
Buck Converter Minimum
On-Time
tSON_MIN
Buck Converter Maximum
Duty Cycle (10)
SDCMAX
Buck Converter Program Output
Voltage Minimum (6,10)
VSVOUT_MIN
Buck Converter Program Output
Voltage Maximum(6,7,8,10)
VSVOUT_MAX
Buck Converter Feedback
Regulation Voltage
Buck Converter Output Voltage(6)
2.8
2.55
VSEN = VBAT, ISVOUT = 10mA
Low IQ mode of PSAVE
84
mV
115
μA
92
3
0.480
VBAT = 3.7V, L = 4.7μH
ISVOUT = 100mA
ns
%
1
VSFB
VSVOUT
V
60
VBAT ≥ VSVOUT_MAX/SDCMAX+150mV
V
V
V
0.500
0.520
2.2
V
V
RS1 = 340kΩ, RS2 = 100kΩ
Buck Converter
Line Regulation(6)
VSVOUT_LINE
Buck Converter
Load Regulation (6)
VSVOUT_LOAD
2.8V ≤ VBAT ≤ 4.5V
ISVOUT = 100mA
-0.3
0.3
%/V
RS1 = 340kΩ, RS2 = 100kΩ
5mA ≤ ISVOUT ≤ 150mA
VBAT = 3.7V
0.002
%/mA
RS1 = 340kΩ, RS2 = 100kΩ
5
SC908
Electrical Characteristics (continued)
Parameter
Symbol
Conditions
Min
Typ
Max
Units
410
440
470
mA
DC-DC Buck Converter (continued)
Buck Converter P-Channel Peak
Current Limit
ILIM_P
Buck Converter P-Channel
On-Resistance
RDS(ON)P
ISVOUT = 150mA
0.75
Ω
Buck Converter N-channel
On-Resistance
RDS(ON)N
ISVOUT = 150mA
1.05
Ω
Buck Converter
Oscillator Frequency
Buck Converter
Start-Up Time (5,10)
fOSC
tSU-SVOUT
0.85
ISVOUT = 150mA, VSVOUT to 95%
VSVOUT = 1V
VSVOUT = 1.8V
VSVOUT = 2.2V
VSVOUT = 3.0V
1.00
0.3
1.3
1.45
1.8
1.15
MHz
ms
2
Linear Low Drop-Out (LDO) Regulator
LDO Input Voltage
LDO Under Voltage
Lockout Rising Threshold
LDO Under Voltage
Lockout Falling Threshold
VLVIN
VBAT ≥ 2.8V
2.2
VTLUVLO-R
1.95
VTLUVLO-F
1.75
LDO Under Voltage
Lockout Hysteresis
VTLUVLO-HYS
LDO Nominal Output
Voltage Minimum (10)
VLVOUT_MIN
VLVIN > VLVOUT +300mV
LDO Nominal Output
Voltage Maximum (10)
VLOUT_MAX
VLVIN > VLVOUT +300mV
LDO Feedback
Regulation Voltage
VLFB
VLVIN = 3.7V, ILVOUT = 1mA
LDO Output Voltage
VLVOUT
RL1 = 54.9kΩ, RL2 = 39.2kΩ
VLVIN = 3.7V, ILVOUT = 1mA
LDO Dropout Voltage
VL_DO
VBAT
V
2.05
V
1.85
V
120
mV
1.5
3.3
V
0.75
1.73
V
V
1.8
1.85
V
VLVOUT = 2.2V, ILVOUT = 100mA
115
200
mV
VLVOUT = 3.0V, ILVOUT = 150mA
130
225
mV
-10
10
mV
-10
10
mV
RL1 = 54.9kΩ, RL2 = 39.2kΩ
LDO Load Regulation
(with respect to 1mA load) (9)
ΔVLVOUT_LOAD
(VLVOUT = 1.8V), VLVIN = 2.2V
1mA ≤ ILVOUT ≤ 100mA
RL1 = 54.9kΩ, RL2 = 39.2kΩ
(VLVOUT = 1.8V), VLVIN = 3.7V
1mA ≤ ILVOUT ≤150mA
6
SC908
Electrical Characteristics (continued)
Parameter
Symbol
Conditions
Min
2.2V ≤ VLVIN ≤ 4.2V referenced to 3.7V,
ILVOUT = 1mA, RL1 = 54.9kΩ, RL2 = 39.2kΩ
-5
Typ
Max
Units
5
mV
Linear Low Drop-Out (LDO) Regulator (continued)
LDO Line Regulation (9)
ΔVLVOUT_LINE
VLVIN = 3.7VDC with 0.5V P-to-P Ripple,
LDO LVOUT/LVIN Power Supply
Rejection Ratio
PSRRLLVIN
LDO LVOUT/(BAT and LVIN)
Power Supply Rejection Ratio
PSRRLBAT
f ≤ 10kHz, VBAT = 3.7VDC
60
dB
60
dB
50
μVRMS
91
μA
VLVOUT = 1.8V, ILVOUT = 30mA
VLVIN = VBAT = 3.7VDC with 0.5V P-to-P
Ripple, f ≤ 10kHz
VLVOUT = 1.8V, ILVOUT = 30mA
10Hz ≤ f ≤ 100kHz
LDO Output Noise Voltage
(9)
VL_NOISE
CLVOUT = 1μF, VLVOUT = 3.0V
VLVIN = 3.7V, ILVOUT = 50mA
LDO Quiescent Current
(ILVIN - ILVOUT ) (4)
LDO Current Limit
LDO Start-Up Time (5, 10)
LDO Turn-Off Time
ILQ
VLVIN = VLEN = VBAT = 4.2V,
VVAD = 0V, ILVOUT = 1mA
IL_LIM
VLVOUT = 0V, VLEN = VBAT
tSU-LVOUT
tTO-LVOUT
300
380
450
mA
Time from LEN (with VSEN = VBAT,
disregard tSU_REF),
VLVOUT from 0V to 95% of final
0.1
ms
Time from LEN
(with VVAD = VSEN = 0, tSU_REF dominates)
VLVOUT from 0V to 95% of final
0
ms
Time from LEN = 0, VLVOUT from 100%
to 10% of regulation
0.5
ms
Battery Voltage Detector
Battery Detector Minimum
Operating Voltage
VDET_MINOP
Battery Detector Maximum
Operating Voltage
VDET_MAXOP
2.3
4.5
Battery Detector Voltage
Warning, Decreasing
VWARN
VDET_MINOP ≤ VBattery ≤ VDET_MAXOP
Battery Detector Voltage Fault,
Decreasing
VDET
RRLBAT = 309kΩ
VDET_HYS
VDET_MINOP ≤ VBattery ≤ VDET_MAXOP
Battery Detector Threshold
Hysteresis, Warning or Fault
3.21
V
3.28
3.35
2.92
150
V
200
V
V
250
mV
7
SC908
Electrical Characteristics (continued)
Parameter
Symbol
Conditions
Min
Typ
Max
Units
10
μA
Logic Control Inputs & Status Outputs
Battery Detector Sense Leakage
(BSEN Current)
IBSEN_DET
VVAD > VADUVLO, or SEN or LEN high,
VBSEN = 4.2V
5
Battery Detector Activation
Delay(10)
VDET_DEL
Time from first of LEN or SEN high until
LBATB/FAULTB valid, VVAD = 0V
70
Logic Input Low
VIL
LEN, SEN; VBAT = 2.7V
Logic Input High
VIH
LEN, SEN; VBAT = 2.7V
1.5
V
Logic Input Current High
IIL
LEN, SEN; VBAT = 2.7V
1
μA
Logic Input Current Low
IIH
LEN, SEN; VBAT = 2.7V
1.5
μA
VOL
ISINK = 2mA
0.5
V
IOH
V = 5V (VVAD = 8V for CPB)
1
μA
CPB, CHRGB, FLTB, LBATB
Outputs
μs
0.4
V
Notes:
(1) VADOP is the “Maximum Vsupply” as defined in EIA/JEDEC Standard No. 78, paragraph 2.11.
(2) The value of the buck converter disabled battery leakage current is included in the charger section battery leakage since it cannot be
independently measured (because SVIN is tied to BAT internally). The buck converter contribution to this value is also included in the Buck
Converter section for design guidance only.
(3) VSYS regulation voltage assumes that VVAD exceeds VVSYS by the VSYS regulator dropout (typically 0.5V at 5mA, for a minimum regulator
RDS = 71Ω). If this condition is not met, then VVSYS = VVAD minus the VSYS regulator dropout.
(4) IQ-Core is the supply current from the battery for common reference circuits into the BAT pin when either the buck converter or LDO or charger
are enabled.
(5) tSU_REF is the start-up time of the voltage reference buffer for both the DC-DC buck converter and the LDO, and should be added to the start-up
time (tSU-SVOUT or tSU-LVOUT respectively) of the first regulator enabled. In the case of the LDO start-up with the switcher disabled, the LDO start-up
time tSU-LVOUT is concurrent with the reference start-up time tSU_REF, and so tSU-LVOUT is specified as typically zero.
(6) SVOUT is the buck converter output node, which is the node at which the output inductor is connected to the load. It is the top of the
feedback resistor divider network. See the Typical Application Circuit.
(7) To guarantee positive load threshold hysteresis for PSAVE-to-PWM mode switching with SVOUT > 2.2V, contact your Semtech representative
for application assistance.
(8) If VBAT < VSVOUT_Max / SDCMAX + 150mV, then the maximum output setting is VBAT x SDCMAX + 150mV. Higher output voltage settings are feasible,
but are subject to load-dependent dropout.
(9) Specified with VBAT = VLVIN.
(10) Guaranteed by design.
8
SC908
Typical Characteristics
Charger CV Line Regulation
Charger CV Load Regulation
ο
ο
TA = 25 C, VVAD = 5V
4.19
4.19
4.189
4.189
4.188
4.188
4.187
4.187
4.186
4.186
VBAT (V)
VBAT (V)
TA = 25 C, IBAT = 50mA
4.185
4.184
4.185
4.184
4.183
4.183
4.182
4.182
4.181
4.181
4.18
4.5
5
5.5
6
6.5
4.18
0
7
50
100
150
200
VVAD (V)
250
300
350
400
450
500
6.75
7
IBAT (mA)
Charger CC Line Regulation
Charger CV Temperature Regulation
VVAD = 5V, IBAT = 50mA
VBAT = 3.75V, RIPRGM = 6.04kΩ
184
4.186
183
4.184
182
4.182
181
ο
IBAT (mA)
VBAT (V)
0C
4.18
4.178
180
179
ο
85 C
178
177
4.176
ο
-40 C
176
ο
4.174
TA = 25 C
175
4.172
-40
-20
0
20
40
60
80
100
120
174
4.5
140
4.75
5
5.25
5.5
o
6
6.25
6.5
Charger CC IFQ Programming
Charger CC VBAT Regulation
ο
VVAD = 5V, RIPRGM = 6.04kΩ
TA = -40, 0, 25, 85 C, VVAD = 5V, VBAT = 3.75V
500
179
178.75
450
178.5
ο
0C
178.25
400
ο
85 C
178
350
ο
TA = 25 C
177.75
177.5
IBAT (mA)
IBAT (mA)
5.75
VVAD (V)
Junction Temperature ( C)
ο
-40 C
177.25
300
250
200
177
176.75
150
176.5
100
176.25
176
3.5
3.6
3.7
3.8
VBAT (V)
3.9
4
4.1
50
2
4
6
8
10
12
14
16
RIPRGM (kΩ)
9
SC908
Typical Characteristics (continued)
Charger I
PreQ
VBAT = 2.6V, RITERM = 4.99kΩ
Charger IPreQ Programming
Line Regulation
VVAD = 5V, VBAT = 2.6V
41.5
70
ο
-40 C
41
60
40.5
50
ο
IBAT (mA)
40
39.5
ο
TA = 25 C
40
30
ο
39
-40 C
20
ο
85 C
ο
38.5
4.75
5
5.25
5.5
5.75
6
6.25
6.5
6.75
0
7
2
4
6
8
10
VVAD (V)
5
500
4.5
450
4
400
VBAT
350
3
300
2.5
250
IBAT
200
1.5
150
1
100
PWR
50
0.5
0.5
0.75
1
1.25
1.5
1.75
2
2.25
VBAT (V), Internal Power Dissipation (W)
700mAhr battery, RIPRGM = 2.15kΩ, RITERM = 3.48kΩ, VVAD = 5.0V, TA = 25 C
550
0.25
500
IBAT
0
2.5
400
3.5
350
3
300
250
2.5
VBAT
2
200
150
1.5
PWR
100
1
50
0.5
2
4
6
8
490
4.8
480
IBAT
470
4.6
460
4.5
450
4.4
440
430
4.3
VBAT
420
4.2
Time (min)
58.5
59
59.5
410
60
VBAT (V), Internal Power Dissipation (W)
500
58
14
16
18
0
20
ο
4.5
IBAT (mA)
VBAT (V)
5
4.9
57.5
12
Re-Charge Cycle Battery Voltage and Current
ο
57
10
Time (s)
CC-to-CV Battery Voltage and Current
56.5
450
4
0
0
700mAhr battery, RIPRGM = 2.15kΩ, RITERM = 3.48kΩ, VVAD = 5.0V, TA = 25 C
510
5.1
4.1
56
20
5
4.5
Time (hrs)
4.7
18
700mAhr battery, RIPRGM = 2.15kΩ, RITERM = 3.48kΩ, VVAD = 5.0V, TA = 25 C
550
5.5
IBAT (mA)
VBAT (V), Internal Power Dissipation (W)
5.5
0
0
16
ο
ο
2
14
Pre-Charging Battery Voltage and Current
Charging Cycle Battery Voltage and Current
3.5
12
RITERM (kΩ)
IBAT (mA)
38
4.5
ο
25 C
TA = 85 C
10
700mAhr battery, RITERM = 3.48kΩ, VVAD = 5.0V, TA = 25 C, Load = 10mA
4
450
400
VBAT
3.5
350
3
300
2.5
250
2
200
150
1.5
1
IBAT (mA)
IBAT (mA)
0C
IBAT
100
50
0.5
PWR
0
0.0
0.5
1.0
1.5
2.0
2.5
3.0
3.5
0
4.0
Time (hrs)
10
SC908
LDO Line Regulation
LDO Load Regulation
ο
ο
RL1 = 54.9kΩ, RL2 = 39.2kΩ, TA = 25 C, VLVIN = 3.75V
RL1 = 54.9kΩ, RL2 = 39.2kΩ, TA = 25 C
1.799
1.799
ILVOUT = 10mA
ILVOUT = 50mA
1.7985
1.798
VLVOUT (V)
VLVOUT (V)
ILVOUT = 100mA
1.797
ILVOUT = 150mA
1.7975
1.796
1.795
2.2
1.798
2.4
2.6
2.8
3
3.2
3.4
3.6
3.8
4
4.2
1.797
0
20
40
60
80
100
120
140
ILVOUT (mA)
VLVIN (V)
LDO Temperature Regulation
LDO PSRR, LVIN to LVOUT
ο
TA = 25 C, VLVOUT = 1.8V, VLVIN = 3.7VDC + 0.5VAC, VBAT = 3.7V
RL1 = 54.9kΩ, RL2 = 39.2kΩ, VLVIN = 3.75V
-45
1.8
ILVOUT = 10mA
ILVOUT = 50mA
1.795
LDO PSRR LLVIN (dB)
ILVOUT = 100mA
1.79
VLVOUT (V)
-50
ILVOUT = 150mA
1.785
1.78
-55
-60
-65
-70
-75
1.775
-80
1.77
-40
-20
0
20
40
60
80
100
-85
10
120
100
o
LDO PSRR, BAT to LVOUT
ο
-45
-50
-50
-55
-55
LDO PSRR LBAT (dB)
LDO PSRR BAT (dB)
TA = 25 C, VLVOUT = 1.8V, VLVIN = VBAT = 3.7VDC + 0.5VAC
-45
-60
-65
-70
-60
-65
-70
-75
-75
-80
-80
100
1000
Frequency (Hz)
10000
LDO PSRR, LVIN and BAT to LVOUT
ο
TA = 25 C, VLVOUT = 1.8V, VLVIN = 3.7VDC, VBAT = 3.7VDC + 0.5VAC
-85
10
1000
Frequency (Hz)
Junction Temperature ( C)
10000
-85
10
100
1000
10000
Frequency (Hz)
11
SC908
Typical Characteristics (continued)
DC/DC Converter Line Regulation
DC/DC Converter Load Regulation
ο
ο
VSVOUT = 2.2V (RS1 = 340kΩ, RS2 = 100kΩ), TA = 25 C, VBAT = 3.7V
VSVOUT = 2.2V (RS1 = 340kΩ, RS2 = 100kΩ), TA = 25 C
2.25
2.23
ISVOUT = 35mA
2.24
2.23
2.22
PSAVE Mode
2.22
2.21
VSVOUT (V)
VSVOUT (V)
ISVOUT = 10mA
2.2
PWM Mode
ISVOUT = 100mA
Decreasing Load
Increasing Load
2.2
2.19
2.18
2.17
2.19
ISVOUT = 150mA
2.18
2.21
3
3.2
2.16
3.4
3.6
3.8
4
2.15
0
4.2
10
20
30
40
50
DC/DC Converter Temperature Regulation
80
90 100 110 120 130 140 150
DC/DC Converter Efficiency
100
2.23
ISVOUT = 35mA
90
80
2.22
PSAVE Mode
PWM Mode
PSAVE Mode
ISVOUT = 10mA
70
Efficiency (%)
VSVOUT (V)
70
VSVOUT = 2.2V (RS1 = 340kΩ, RS2 = 100kΩ), VBAT = 3.6V, L = 4.7 μH
VSVOUT = 2.2V (RS1 = 340kΩ, RS2 = 100kΩ), VBAT = 3.7V
2.21
2.2
PWM Mode
ISVOUT = 100mA
60
50
40
30
20
2.19
ISVOUT = 150mA
2.18
-40
-20
0
20
10
40
60
80
100
0
0
120
10
20
30
40
o
50
60
70
80
90 100 110 120 130 140 150
Junction Temperature ( C)
ISVOUT (mA)
DC/DC Converter Efficiency Detail
DC/DC Converter Efficiency — Low Loads
VSVOUT = 2.2V (RS1 = 340kΩ, RS2 = 100kΩ), VBAT = 3.6V, L = 4.7 μH
VSVOUT = 2.2V (RS1 = 340kΩ, RS2 = 100kΩ), VBAT = 3.6V, L = 4.7 μH
100
93
92
60
ISVOUT (mA)
VBAT (V)
PSAVE Mode
PSAVE Mode
90
80
PWM Mode
91
PWM Mode
89
88
Efficiency (%)
Efficiency (%)
70
90
60
50
40
30
87
20
86
85
0
10
10
20
30
40
50
60
70
80
ISVOUT (mA)
90 100 110 120 130 140 150
0
1
10
100
ISVOUT (mA)
12
SC908
Pin Descriptions
Pin #
Pin Name
Pin Function
1
VAD
Charger input pin
2
VSYS
Adapter input internal-regulation node which also serves as supply for EN_NTC, RTIME, and all input-referenced
(vs. battery-referenced or regulated output-referenced) pull-ups; load must not exceed 5mA.
3
IPRGM
Pin for setting constant current charging current — connect resistor to ground to set current.
4
ITERM
Pin for setting termination and precharge current — connect resistor to ground to set current.
5
RTIME
Charge timer pin — connect a resistor to ground to set timer, ground to disable the timer. Timer enabled with
internally programmed default time is selected with RTIME tied to VSYS.
6
RLBAT
Resistor is connected to ground to set Low Battery voltage threshold.
7
LVIN
8
LVOUT
9
LFB
LDO feedback voltage input
10
VREF
Bandgap reference bypass pin — connected to a 10nF capacitor to analog ground. No other connections are
permitted.
11
AGND
Analog ground pin — refer to grounding considerations in application section.
12
DGND
Digital ground pin — refer to grounding considerations in application section.
13
LEN
LDO enable pin — active high
14
SFB
DC-DC converter feedback input — connect voltage divider from output to this pin to set output voltage.
15
FLTB
Charging Fault indicator — open drain output is active low when a charging fault has occurred. Also, together
with LBATB, indicates when battery discharges below a programmable voltage set by RLBAT resistor.
16
LBATB
17
CPB
Charger Present indicator — open drain output is active low when a valid VAD input voltage is present.
18
SEN
DC-DC converter enable pin — active high
19
CHRGB
Charging-In-Progress indicator — open drain output is active low when charging until charging current drops
below the programmed termination current, or until charging is disabled by charge timeout or EN_NTC disable or
NTC temperature fault.
20
PGND
DC-DC converter power ground pin — No other connection is permitted.
21
SLX
DC-DC converter output — connect to an inductor between this point and SVOUT (the DC-DC converter load connection).
22
BAT
Charger output pin, also DC-DC converter input pin — connect to the positive battery terminal.
23
EN_NTC
24
BSEN
T
Thermal Pad
LDO voltage input — can be connected to either the battery supply (BAT) or the switching regulator output
(SVOUT). No other connections are permitted.
LDO voltage output
Low Battery indicator — open drain output is active low when battery discharges below 3.3V, and, together with
LBATB, indicates when battery discharges below a programmable voltage set by RLBAT resistor.
NTC thermistor input — charger is enabled if voltage is between 0.3 × VSYS and 0.75 × VSYS. Charger is disabled if
voltage is below 1V. Battery temperature fault otherwise.
Battery Kelvin sense pin — independent connection is tied directly to the battery positive terminal.
Connect to ground plane with thermal vias directly under pad.
13
SC908
Block Diagram With Typical Application Circuit
2
VSYS
VAD
VSYS
Regulation
CVSYS
Qterm
VSYS
10
Reference
Voltages
CVAD
Qpass
4.2V
VREF
1
Charging
Adapter
VREF
BSEN
24
Fast Charge Ref
Pre-Charge Ref
CVREF
VTH-cold
VTH-hot
(0.75VCC)
(0.3VCC)
Control
EN_NTC
RNPU
Pre-Charge On
Fast Charge On
Over Temp
Under Voltage
Over Voltage
BAT
Pre-Charge Ref
CVOUT
NTC
Interface
23
ITERM
RNTC
RRTIME
5
22
RTIME
IPRGM
Timer
4
RITERM
3
Fast Charge Ref
17
19
15
16
RIPRGM
VREF
CPB
LVIN
CHRGB
CLVIN
7
LDO
FLTB
LDO
Supply
from
battery or
SVOUT
LVOUT
8
LBATB
LFB
9
RL1
CLVOUT
RL2
AGND
RRLBAT
6
13
18
11
RLBAT
SVIN
Buck
Converter
Control Block
LEN
SEN
SLX
21
PGND
12
DGND
20
LS
SFB
14
RS2
CSFG
RS1
SVOUT
CSFB
CSVOUT
14
SC908
Applications Information
Charger Operation
The SC908 Li-Ion battery charger can be configured independently with respect to fast-charge, termination current,
and timing. The charging and battery voltage status are
indicated by the four status outputs.
A charge cycle is initiated when the power adapter is connected to the device and the SC908 VAD pin voltage is
between the Under-Voltage LockOut (UVLO) rising threshold and the input Over Voltage Protection (OVP) threshold.
If the battery voltage is less than the pre-charge threshold,
the output current is regulated to the programmed precharge current. When the pre-charge threshold voltage is
exceeded, the fast-charge Constant Current (CC) mode
begins, with the charge current rising to the programmed
fast-charge current in three soft-start current steps. The
charger enters the Constant Voltage (CV) mode when the
battery voltage rises to its final value (VCV ), typically 4.2V.
In the CV mode the BAT voltage is regulated to VCV, and as
the battery continues to charge it accepts decreasing
current. The CHRGB output turns off when IBAT drops
below the programmed termination current. If the charge
timer is active, the battery is held in the CV charge mode
until the timer cycle ends. The charger then enters the
monitor mode, where the output remains off until the
voltage at BAT drops by VTReQ, and a new charge cycle is
initiated. If the charge timer is disabled, the monitor mode
is immediately entered upon charge termination.
when VAD is cycled off and on, or when the EN_NTC pin
is forced low to disable the charger.
Fast-Charge Constant Current Mode
The fast-charge CC mode is active when the battery
voltage is above VTPreQ and less than VCV. The current can
be set to a maximum of 0.5A and is selected by the
program resistor on the IPRGM pin. The voltage on this
pin represents the charger output current. This allows
the charging current to be measured by sensing the
IPRGM pin voltage using a general purpose Analog-toDigital Converter (ADC) and the host microporocessor.
The fast-charge current is determined by
IFQ
VIPRGM _ Typ
u 697
RIPRGM
Excellent fast-charge current accuracy is obtained by the
use of a patented polarity-switched current sense
amplifier (US Patent 6,836,095). This nullifies current
measurement offset errors, leaving only a small gain
error. The range of expected fast-charge output current
versus programming resistance RIPRGM is shown in Figures
1a and 1b.
520
500
480
460
Pre-Charge Mode
The pre-charge mode is automatically entered when the
battery voltage is below the pre-charge threshold voltage,
which preconditions the battery for fast charging. The
pre-charge current value is set by the resistor on the ITERM
pin, and is programmable from 14mA to 65mA. The precharge current is determined by
Fast Charge Current (mA)
440
420
400
380
360
340
320
300
280
260
240
220
IPr eQ
VITERM _ Typ
u 130
RITERM
where VITERM_Typ designates the typical value of VITERM. (See
the Termination Current section for precharge current
accuracy.) When the timer is enabled, there is a maximum
allowed pre-charge duration. If the pre-charge time
exceeds 25% of the total charge cycle, the charger will
turn off due to a pre-charge fault. This fault is cleared
200
180
2
2.5
3
3.5
4
4.5
5
5.5
RIPRGM (kΩ)
Figure 1a — Fast-charge Current Variation vs. IPRGM
Resistance, Low Resistance Range
15
SC908
Applications Information (continued)
Fast Charge Current (mA)
180
160
140
120
100
80
60
5.5
6
6.5
7
7.5
8
8.5
9
9.5
10 10.5 11 11.5 12 12.5 13 13.5 14 14.5 15
RIPRGM (kΩ)
Figure 1b — Fast-charge Current Variation vs. IPRGM
Resistance, High Resistance Range
The figures show the nominal current versus nominal
RIPRGM resistance as the center plot and two theoretical
limit plots indicating maximum and minimum current
versus nominal programming resistance. These plots are
derived from models of the expected worst-case contribution of error sources depending on programmed
current. The current range includes the uncertainty due
to 1% tolerance resistors. The dots on each plot indicate
the currents obtained with standard value 1% tolerance
resistors. The figures show low and high resistance
ranges.
Termination Current
When the battery voltage reaches VCV, the SC908 transitions from constant current mode to constant voltage
mode. As the output holds the voltage measured at the
BSEN pin constant, the current through the battery will
decrease as the battery becomes fully charged. CHRGB is
disabled when the output current drops below the programmed termination current. If the timer is enabled, the
output will continue to float-charge in CV mode until the
charge timer expires. If the timer is disabled, the output
will turn off as soon as the termination current level is
reached. The termination current is determined by
ITERM
IPr eQ
Termination current can be programmed from 14mA to
65mA, and must be less than IFQ for correct operation of
the charge cycle. Pre-charge and termination current
regulation accuracy is dominated by offset error. The
range of expected pre-charge output current and termination threshold current versus programming resistance
RITERM is shown in Figures 2a and 2b. The figures show the
nominal pre-charge and termination current versus
nominal resistance as the center plot. Two theoretical
limit plots indicate maximum and minimum current
versus nominal programming resistance. These plots are
derived from models of the expected worst-case contribution of error sources depending on programmed
current. The current range includes the uncertainty due
to 1% tolerance resistors. The dots on each plot indicate
the currents obtained with standard value 1% tolerance
resistors. The figures show low and high resistance
ranges.
A sufficient separation between IFQ and ITERM must be
maintained to ensure proper operation of the constant
current regulator and charge termination detector. RIPRGM
and RITERM must be chosen to nominally satisfy
IFQ > ITERM + 90mA
75
70
65
Precharge/Termination Current (mA)
200
60
55
50
45
40
35
30
25
20
3
3.5
4
4.5
5
5.5
6
6.5
RITERM (kΩ)
Figure 2a — Pre-charge and Termination Current
Variation vs. ITERM Resistance, Low Resistance Range
VITERM _ Typ
u 130
RITERM
16
SC908
Applications Information (continued)
the battery voltage falls below the recharge threshold
(VCV - VReQ), the charger will clear the charge timer and initiate a charge cycle. The status of the charger output as a
function of the Charge Complete timer status and IBAT is
shown in Table 1.
40
Precharge/Termination Current (mA)
35
30
25
Table 1 — Charger Output Status
20
Timer
Iout
Output State
t < Timeout
N/A
On
15
10
t > Timeout
N/A
Off
Disabled
< Itermination
Off
5
0
6.5
7
7.5
8
8.5
9
9.5
10
10.5
11
11.5
12
12.5
13
13.5
14
RITERM (kΩ)
Figure 2b — Pre-charge and Termination Current
Variation vs. ITERM Resistance, High Resistance Range
Remote Kelvin Sensing at the Battery
The BSEN pin provides for Kelvin sensing of the battery
positive terminal voltage. This prevents feedback error
due to charging, battery load, and switching regulator
input currents flowing over resistive PCB traces.
Charge Timer
The timer provides over-charging protection in the event
of a faulty battery and maximizes charging capacity. The
RTIME pin is connected to VSYS to select the internal
(default) time duration of three hours, and to GND to
disable the timer. Connecting a resistor between RTIME
and GND will program the Charge Complete Time-Out, in
hours, according to the equation
t QComp
RRTIME
1
u
3.334 3600
The timer is programmable over the range of 2 to 6 hours.
The output is automatically turned off when the charge
timer cycle ends.
If the charge cycle remains in precharge for longer than
one fourth of the Charge Complete Time-Out period, a
charging fault is detected and the charger turns off. The
Precharge Fault Time-Out period, in minutes, is
tPr eQF
t QComp
u 60
4
Monitor Mode
When a charge cycle is complete (termination if the timer
is disabled, charge timeout if the timer is enabled), the
output turns off and the device enters monitor mode. If
Optimal PCB layout routes the BSEN trace directly to the
battery positive terminal connection on the PCB to
achieve the most accurate sensing of battery cell voltage.
Connecting BSEN to BAT directly at the SC908 will introduce battery voltage measurement error that can cause
an improper transition from CC to CV regulation, lengthening the charge time. This error could also raise or lower
the final battery voltage, and may alter the final
state-of-charge.
EN_NTC Interface
The EN_NTC pin is the interface to a battery pack temperature sensing Negative Temperature Coefficient (NTC)
thermistor, which can be used to suspend charging if the
battery pack temperature is outside of a safe-to-charge
range. It is also the charger-disable input. The typical
EN_NTC network is a fixed resistor from VSYS to the
EN_NTC pin, and the battery pack EN_NTC thermistor
from the EN_NTC pin to ground. In this configuration, an
increasing battery temperature produces a decreasing
NTC pin voltage.
When VEN_NTC is greater than the high (cold) threshold or
less than the low (hot) threshold, the charge cycle is suspended by turning off the output. This suspends but does
not reset the charge timer, and indicates a fault on the
FLTB pin. Hysteresis is included for both high and low
17
SC908
Applications Information (continued)
NTC thresholds to avoid chatter at the NTC fault thresholds. When VEN_NTC returns to the valid range, the charge
timer resumes and the charge cycle continues. The charge
timer will expire when the output on-time exceeds the
timer setting, regardless of how long it has been disabled
due to an NTC fault.
Using the recommended NTC external network, the
EN_NTC pin voltage and the internal hot and cold NTC
thresholds are all ratios of VVSYS, rather than absolute voltages. This ensures that the hot and cold OK-to-charge
thresholds are insensitive to the VSYS pin output voltage.
The ratiometric thresholds are given by the parameters
RTNTCH and RTNTCC. EN_NTC pin voltage VEN_NTC between
RTNTCH×VVSYS and RTNTCC×VVSYS enables charging. When VEN_NTC
is outside this range, charging is suspended and the FLTB
output is asserted (pulled low).
When VEN_NTC < VTNTCDIS (nominally 0.6V), the SC908 charger
is disabled. The EN_NTC pin can be pulled to ground by
an external n-channel FET or microprocessor GPIO to
asnychronously disable or reset the device. When VEN_NTC <
VTNTC_DIS, the charger is turned off, the charge timer is reset,
and the CHRGB status output is turned off. While disabled,
the VAD input UVLO and OVP threshold detectors remain
active, and the CPB pin continues to indicate whether the
VAD input voltage is valid for charging.
The response of the SC908 to an EN_NTC pin voltage
above the high threshold or below the low threshold (but
above VTNTCDIS) is the same. Therefore the EN_NTC network
can be configured with the battery pack thermistor
between EN_NTC and VSYS, and a fixed resistor between
EN_NTC and ground. This configuration may be used to
reset the charge timer (and the CHRGB output) when the
battery pack is removed; the fixed resistor pulls the NTC
pin to ground to disable the charger without indicating a
fault.
NTC Design Example
This example uses the conventional NTC network configuration shown in the block diagram. A fixed resistor (RNPU)
is connected between EN_NTC and VSYS, and a battery
NTC thermistor (RNTC) is connected between the EN_NTC
pin and ground. The battery temperature range over
which charging is permitted is from 0°C to 40°C. The data-
sheet for the proposed NTC thermistor, the Mitsubishi
TH11-3T223F, indicates that RNTC = 11.93kΩ at 40°C, and
R NTC = 69.41k Ω at 0°C, with a dissipation constant
DC = 3.0mW/°C. So RHOT = 11.93kΩ and RCOLD = 69.41kΩ.
Step 1
Select RNPU to obtain one of the desired temperature
thresholds. This example will solve for the hot threshold
for the normal (NTC thermistor to ground) configuration,
then evaluate the cold threshold. Solve the NTC network
voltage divider for R NPU to place the NTC voltage at
RTNTC_HF × VVSYS when RNTC = RHOT.
RTNTC _ HF u VVSYS
VVSYS u RHOT
RNPU RHOT
or, solving for RNPU,
RNPU
1 RTNTC _ HF
u RHOT
RTNTC _ HF
Using RTNTC_HF = 0.3, we obtain RNPU = 27.837kΩ exactly.
The closest 1% standard nominal value is RNPU = 28.0kΩ.
Step 2
Evaluate the NTC network at the cold threshold. Compute
the NTC network resistor divider voltage as a function of
VVSYS at the desired cold threshold.
NTC COLD
VVSYS u R COLD
R NPU R COLD
0.7126 u VVSYS
The value 0.7126 should be close to the nominal value of
RTNTC_CR = 0.75. To evaluate the significance of the discrepancy, an estimate of the actual cold threshold is obtained
by evaluating the value of R NTC_Cold_Actual that produces
the nominal value of RT NTC_CR = 0.75.
RTNTC _ CR
RNTC _ Cold _ Actual
RNTC _ Cold _ Actual RNPU
The solution shows RNTC_Cold_Actual = 84.0kΩ. Examination of
the thermistor specification resistance versus temperature
data indicates that the resulting actual cold threshold is
approximately -4°C, compared to the target of 0°C.
18
SC908
Applications Information (continued)
Step 3
With the example thermistor, there is no choice of RNPU
that will yield the specified results at both hot and cold
limits. A more sensitive thermistor, one with a wider percentage variation in resistance at the desired threshold
temperatures, may provide a better solution. Steps 1 and
2 are repeated using other devices from the same vendor,
seeking a closer match at the cold threshold.
The Mitsubishi TH11-4C153F was the final selection. Its
characteristics are: RHOT is 7.73kΩ (at 40°C), RCOLD is 53.94kΩ
(at 0°C). Its dissipation constant DC = 3.0mW/°C. Step 1
yields RNPU = 18.2kΩ, with the result that NTCCOLD/VVSYS =
0.748 ≈ RTNTC_CR, NTCHOT/VVSYS = 0.298 ≈ RTNTC_HF. The NTC
resistances that give the exact cold and hot thresholds
RTNTC_CR and RTNTC_HF are 54.6kΩ (which is RNTC at approximately -0.5°C) and 7.80kΩ respectively, closely matching
the resistance of the thermistor at the targeted threshold
temperatures.
Step 4
Verify acceptable thermistor self heating. The dissipation
constant is the power rating of the thermistor resulting in
a 1°C self heating error. Since accuracy is important only
at the thresholds, self heating is assessed only at 0°C and
40°C.
For VVSYS = 4.6V, the 0°C NTC network current is
INTC_COLD = VVSYS/(RNPU + RCOLD) = 63.8μA
Power dissipation in the thermistor at this temperature is
PCOLD = RCOLD × (INTC_COLD)2 = 0.219mW
The self heating error is
TSH _ COLD
0.219mW
3 mW C
0.073qC
The 40°C NTC network current
INTC_HOT = VVSYS/(RNPU + RHOT ) = 0.177mA
for self heating of approximately 0.081°C. The actual cold
and hot thresholds will be 0.073 and 0.081 degrees lower
than designed, respectively, which are negligible errors.
Logical CC-to-CV Transition
The SC908 differs from most monolithic linear single cell
Li-Ion chargers, which implement a linear transition from
CC to CV regulation. The linear transition method uses
two simultaneous feedback signals — output voltage and
output current — to the closed-loop controller. When the
output voltage is sufficiently below the CV regulation
voltage, the influence of the voltage feedback is negligible
and the output current is regulated to the desired current.
As the battery voltage approaches the CV regulation
voltage (4.2V), the voltage feedback signal begins to influence the control loop, which causes the output current to
decrease although the output voltage has not reached
4.2V. The output voltage limit dominates the controller
when the battery reaches 4.2V and eventually the controller is entirely in CV regulation. This system may be
characterized as a dual-constraint (voltage and current)
controller, with a soft transition between constraints. The
soft transition effectively reduces the charge current
below that which is permitted for a portion of the charge
cycle, which increases charge time.
In the SC908, a logical transition is implemented from CC
to CV to recover the charge current lost due to the soft
transition. The controller regulates only current until the
output voltage exceeds the transition threshold voltage.
It then asynchronously switches to CV regulation. The
transition voltage from CC to CV regulation is typically less
than 10mV higher than the CV regulation voltage, which
provides a sharp and clean transition free of chatter
between regulation modes. The difference between the
transition voltage and the regulation voltage is the CC/CV
overshoot. While in CV regulation, the output current is
limited to approximately 105% of the fast-charge current
programmed by the IPRGM pin or the IPUSB pin, depending on the charging input selected, providing mode
transition hysteresis. If the output current exceeds this
current limit threshold, the controller asynchronously
reverts to current regulation.
Power dissipation in the thermistor at this temperature is
PHOT = RHOT × (INTC_HOT )2 = 0.243mW
The logical transition from CC to CV results in the fastest
possible charging cycle that is compliant with the speci19
SC908
Applications Information (continued)
fied current and voltage limits of the Li-Ion cell. The output
current is constant at the CC limit, then decreases abruptly
when the output voltage steps from the overshoot voltage
to the regulation voltage at the transition to CV control.
This can be compared to voltage and current trajectories
for other monolithic charger devices to show the softness
of the linear crossover. This explains the charge-time
advantage of the SC908 logical crossover method.
Input Over-Voltage Protection
The VAD input is protected from adapter over-voltage to
at least 28V above VDGND. When VVAD exceeds its OVP rising
threshold VADOVP-R the charger turns off its output while
the charge timer continues to run, and the FLTB status
indicator is asserted. When VVAD subsequently falls below
the VAD OVP falling threshold VADOVP-F, charging continues
normally and FLTB is released.
Charger Protection Features
Thermal Protection
The charger’s internal over-temperature (OT) threshold is
set to approximately 145°C. If the temperature exceeds
this threshold prior to termination, the charger output is
turned off. All other functions remain active, the charger
logical state is preserved, and no fault is indicated. This
allows thermal pulse charging in conditions of high power
dissipation. Following termination, a charger OT condition will be indicated as a fault. Refer to the Indicator Flags
subsection for more information.
The protection features are:
•
•
•
•
Short Circuit Protection
Over Current and Max Temperature Protection
Input Overvoltage Protection
Thermal Protection
Short Circuit Protection
The BAT output can tolerate an indefinite short circuit to
ground. The current into a ground short will be equal to
the precharge current.
The ITERM pin voltage prior to termination, and the IPRGM
pin voltage while in CC mode, are regulated to 1.5V.
Precharge current and termination current are proportional to the resulting ITERM current, and CC current is
proportional to the resulting IPRGM current. High battery
current is prevented by pinshort detectors on both programming pins. Pinshort detection asynchronously forces
the charger into reset, turning off the output and clearing
the charge timer. When the pinshort condition is removed,
the charger begins normal operation automatically.
Over Current and Max Temperature Protection
Over current protection is provided in all modes of operation. When the device is in the charge mode the output is
current-limited to either the programmed pre-charge
current or the programmed fast charge current, depending on the voltage at the output. Junction over-temperature
protection allows operation with maximum power dissipation by disabling the charger output current when the
die temperature reaches the maximum operating temperature. This results in operation as a pulse charger in
extreme power dissipation applications, delivering the
maximum allowable output current while limiting the
internal die temperature to a safe level.
A second high OT threshold is set to approximately 165°C.
Should the die temperature exceed this threshold, all
SC908 functions are disabled, and the status outputs indicate an exceptional condition fault. Refer to the Indicator
Flags subsection for more information.
Low Battery Detector Operation
The low battery detector provides two low battery detection voltage thresholds: a fixed warning threshold and a
resistor programmable detection (shutdown request)
threshold. The low battery detector is enabled when
either the buck converter is enabled (SEN is high) or the
LDO regulator is enabled (LEN is high). The warning and
shutdown request are provided by the status output pins
FLTB and LBATB, as described in the Status Outputs subsection. When a charging adapter is present (V VAD >
VADUVLO-x), the FLTB and LBATB outputs are redefined to
reflect the interaction of battery voltage and charging
state.
The low battery detector warning threshold is fixed at
3.28V ± 70mV. The battery voltage fault threshold is programmable, with a resistor from the RLBAT pin to ground,
20
SC908
Applications Information (continued)
from 2.77V to 2.98V, ±10%. The low battery fault threshold
is set by the relationship
When VVAD is between its UVLO and OVP thresholds, VVAD
is valid to charge, and the CPB output is low indicating
that a charging adapter is present.
VDET = 3.9 μA × RRLBAT × 2.42
The CHRGB output indicates the battery charging status.
The charger-present status output states are described in
Table 3. When pre-charging or when the output current
is greater than ITERM, CHRGB is low. The CHRGB output is
latched off (high) when the output current becomes less
than ITERM during the charge cycle (and the battery voltage
is above the recharge threshold, VBSEN > VCV - VTReQ). This
latch is reset when the battery enters a recharge cycle
(VBSEN < VCV - VTReQ), or for any NTC_EN range other than
OK-to-charge, or if VVAD is above or below the VAD validto-charge range, allowing CHRGB to become active again
when charging resumes.
RRLBAT must satisfy the condition
294kΩ ≤ RRLBAT ≤ 316kΩ
Connect RLBAT to GND to disable the Low Battery Detector
fault. The Low Battery Detector warning remains active.
Status Outputs
Four charger status outputs/LED drivers are provided.
•
•
•
•
CPB (Charger Present)
CHRGB (Charge Active)
FLTB (Fault)
LBATB (Low Battery Warning)
When a charging adapter is present, the FLTB and LBATB
outputs are redefined to reflect the interaction of the
battery voltage, charging state, and charging faults, as
described in Table 3. The FLTB output is activated when
the device experiences a charger fault condition, or
(together with LBATB output) when the battery voltage is
less than the resistor-programmed low-battery detector
threshold, VDET. This output can be used to notify the
system controller of a fault condition when connected to
an interrupt input, or it can be used like CPB and CHRGB
to drive an indicator LED.
These outputs are active-low, open drain NMOS drivers
capable of sinking up to 2mA each. The state of each, in
various operating conditions, is defined in Tables 2, 3,
and 4.
When the VAD voltage is below its UVLO threshold (no
charging adapter is present), the CPB and CHRGB outputs
are off (high impedance). The FLTB and LBATB outputs
indicate the battery voltage as defined in Table 2.
Table 2 — Status Output State, Charging Adapter Absent
Conditions
T
off
off
off
on
T
off
off
on
on
T
VDET ≥ VBSEN
off
VWARN > VBSEN > VDET
VVAD < VADUVLO
off
VBSEN ≥ VWARN
LBATB
off
Description
Battery Voltage
(mutually exclusive)
and
Comments
VVAD > VADOVP
FLTB
off
VADUVLO < VVAD < VADOVP
CHRGB
Adapter Voltage
(mutually exclusive)
CPB
Status Pins Output State
(on = low)
T
on = open drain output driver is active
off = output is not active
T = listed condition is true
F = listed condition is false
- = don’t care
Blank = mutually exclusive with another condition
No Charging Adapter, Battery Voltage Good
T
No Charging Adapter, Low Battery Voltage Warning
T
No Charging Adapter, Low Battery Shutdown Request
21
SC908
Applications Information (continued)
The fault modes signaled by FLTB are:
•
•
•
•
When any of these conditions occurs the FLTB output goes
low; otherwise it remains high impedance.
input over-voltage
battery NTC temperature out of range
pre-charge timeout.
charger-only over-temperature (low OT, posttermination only)
The LBATB output is active when the battery voltage is
below the low-battery warning voltage, VWARN, if the charging adapter is absent. If CPB and CHRGB outputs are both
active, LBATB indicates when the charger is in precharge
mode. However, LBATB and FLTB active together always
Table 3 — Status Output State, Charging Adapter Present
Conditions
Status Pins
Output State
(on = low)
Adapter
Voltage
(mutually
exclusive)
Battery
Voltage
(mutually
exclusive)
EN_NTC
(mutually
exclusive)
Charging State,
Charging Faults
(Internal signals)
Description
and
Pre-Charging
Pre-Term Charging
-
-
-
-
T
F
-
-
Pre-Charge Timeout
BAT Short-to-GND
T
T
Charger OT
NTC Hot or Cold
NTC OK
Disable
VDET ≥ VBSEN
VWARN > VBSEN > VDET
off
VBSEN ≥ VWARN
LBATB
off
VVAD > VADOVP
FLTB
off
VADUVLO < VVAD < VADOVP
CHRGB
on
VVAD < VADUVLO
CPB
Comments
F
VVAD valid, Charger Disable/Reset OR
Charging Done (Die Temperature OK)
F
F
F
F
-
-
-
-
F
VVAD valid and Low Battery Warning,
Charger Disable/Reset OR
Charge Cycle Pending (about to begin)
F
-
-
F
VVAD valid,
Battery Temperature Fault OR
Charger Over-Temp Fault (Die Temp > TCHRGR_OT )
-
-
-
-
-
-
-
F
T
-
F
F
-
T
-
-
VVAD valid, Low Battery Detected, with either
Charger Disable/Reset OR
Battery Temperature Fault OR
Charger Over-Temp Fault OR
BAT short-to-ground
T
on
off
off
on
T
T
T
T
on
off
on
off
T
-
-
T
T
T
on
off
on
on
T
-
F
T
T
T
F
-
-
on = open drain output driver is active
off = output is not active
T = listed condition is true
F = listed condition is false
- = don’t care
Blank = mutually exclusive with another condition
on
on
off
off
T
-
-
F
T
-
F
F
T
F
VVAD valid, Pre-termination Charging,
Battery Voltage > VDET
on
on
off
on
T
-
-
F
T
F
F
T
T
F
VVAD valid, Pre-Charging (trickle charging),
Battery Voltage > VDET
on
on
on
off
T
-
-
F
T
T
F
T
T
F
VVAD valid, Pre-Charging with Charger Over-Temp
Fault, Battery Voltage > VDET
on
on
on
on
T
T
T
-
F
-
T
F
VVAD valid, Battery Voltage < VDET
Pre-Charging or Pre-Termination Charging
22
SC908
Applications Information (continued)
The load on VSYS should not exceed 5mA. If CHRGB is
used to operate an indicator LED, it is recommended that
the CHRGB status pin be pulled up to the battery or to a
battery-powered regulated supply. Since CHRGB is
asserted only while charging the battery, the current sunk
by CHRGB will be sourced by the charger output and will
not discharge the battery.
indicates that the battery voltage is below the low-battery
detect threshold, VDET. Table 3 gives a comprehensive
description of all combinations of status output states
while the adapter input is valid for charging.
Exceptions to these charging conditions occur when
certain events happen in combination. Table 4 describes
status condition exceptions. These exceptions include
VVAD > OVP threshold; a high over temperature condition,
in which device temperature exceeds the higher of two
over-temperature thresholds, causing charging and both
regulators to be disabled; a precharge timeout, which
may indicate a faulty battery.
Because VSYS is powered from VAD, it is unsuitable as a
pullup source for the FLTB and LBATB status pins. These
status pins must be powered from the battery or batterypowered regulated supply to function as battery level
indicators when the charging adapter is not present.
VSYS pin
Capacitor Selection
The voltage of the VSYS pin is regulated from the VAD input
and is present only when VAD is powered. VSYS provides
an external voltage reference and supply for the NTC
network, and a pull-up supply voltage for the CPB status
indicator. A capacitor of at least 0.1uF should be connected from VSYS to ground near the pin.
Low cost, low ESR ceramic capacitors such as the X5R and
X7R dielectric material types are recommended. The BAT
pin capacitor, CBAT, range is 1μF to 22μF. This capacitor
functions as both the charger output capacitor and as the
switching regulator input capacitor. The VAD pin input
capacitor CVAD is typically between 0.1μF to 2.2μF; however,
larger values will not degrade performance.
Table 4 — Status Output State, Exception Conditions
Conditions
Status Pins Output State
(on = low)
Adapter
Voltage
(mutually
exclusive)
Battery
Voltage
(mutually
exclusive)
EN_NTC
(mutually
exclusive)
Description
Charging State,
Charging Faults
(Internal signals)
and
T
off
on
on
off
-
-
-
-
off
on
on
on
F
-
-
-
Pre-Charge Timeout
on
Pre-Term Charging
on
Pre-Charging
off
BAT Short-to-GND
off
Charger OT, (High OT)
T
NTC Hot or Cold
off
NTC OK
on
Disable
off
-
-
-
-
-
-
-
F
VAD Overvoltage,
Battery Voltage Good or Warning
T
-
-
-
-
-
-
-
F
VAD Overvoltage, Low Battery Detect
-
-
-
-
-
Hi OT
-
-
-
-
High-Over-Temperature Detection (die
temperature > TOT; all functions shutdown.)
-
-
F
-
-
-
-
-
-
T
Pre-charge Timeout, NTC Not Disable,
Adapter Voltage Good or OVP
VDET ≥ VBSEN
off
VWARN > VBSEN > VDET
LBATB
VBSEN ≥ VWARN
FLTB
VVAD > VADOVP
CHRGB
VADUVLO < VVAD < VADOVP
CPB
VVAD < VADUVLO
Comments
T
T
on = open drain output driver is active
off = output is not active
T = listed condition is true
F = listed condition is false
- = don’t care
Blank = mutually exclusive with another
condition
23
SC908
Applications Information (continued)
LDO Regulator
The low-noise low-dropout (LDO) voltage regulator operates from an LVIN pin input voltage range of 2.2V up to the
battery voltage (VBAT ), and an output voltage from 1.5V to
3.3V, programmable with external resistors. The SC908
has a VREF bypass pin to enable the user to capacitively
decouple the bandgap reference (10nF recommended)
for very low output noise (50μVRMS typically).
The output voltage of the LDO regulator is divided externally using a resistor divider and compared to the buffered
bandgap voltage, typically 0.75V. The error amplifier
drives the gate of a low RDS(ON) P-channel MOSFET pass
device.
Enabling the LDO
The LDO has an independent enable input pin (active
high). The LDO can be enabled only if VLVIN ≥ VTLUVLO, typically 2.0V, although performance specifications are
guaranteed for VLVIN ≥ 2.2V. The LDO output will settle to
within 5% of its final value in 0.1ms (typically) when the
bandgap reference buffer has already settled (when the
switching regulator is already enabled, or when the charging adapter is present). A fast start-up circuit is used to
speed the initial charging time of the VREF pin bypass
capacitor. This is done so that the LDO output voltage will
settle to within 5% of its final value in 0.4ms (typically)
when the LDO is the first resource enabled. When the
battery charger is in its precharge mode of operation
(trickle charging of a deeply discharged battery), the LDO
enable signal will be disregarded until fast-charging
begins (at a battery voltage of 2.8V typically). An exception occurs when either the LDO or switching regulator
are already enabled. At this time when a charging source
is applied and the charger enters precharge mode, the
LDO will remain enabled (or can become enabled).
Precharge mode is indicated by the status outputs. (Refer
to Table 3.)
The LDO provides active shutdown. The capacitance on
LVOUT will be discharged by an on-chip FET when the
LDO is disabled.
Programming the LDO Output Voltage
The LDO regulates its output to obtain 0.75V at the LFB
pin. The output can be programmed to any voltage from
1.5V to 3.3V by an external resistor divider network from
LVOUT to LFB. The output voltage is set by
9/9287
9/)%
5 /
5/ LFB is a high impedance input, so large value resistors,
even on the order of 500kΩ, may be used to meet the
noise specification. When considering the effect of LDO
load current on performance specifications, the current
flowing in the feedback divider network should be
included in the load. The LDO is internally compensated.
No feedback capacitor is required for stability.
LDO Dropout
The LDO dropout voltage is the product of the minimum
RDS(ON) of the P-channel MOSFET pass device and the LDO
output current. As VLVIN decreases, the achievable sourceto-gate voltage of the pass device decreases, so the
minimum achievable RDS(ON) becomes larger. This is the
reason for the two-tier dropout specification. Minimum
RDS(ON) increases with die temperature, which is affected
not only by LDO power dissipation, but also by switching
regulator and charger power dissipation. The maximum
dropout is specified for a temperature of 85°C.
LDO Reference Voltage
The internal bandgap reference voltage must be externally bypassed to meet the LDO noise specification. A
10nF ceramic capacitor from the VREF pin to AGND is recommended to bypass the bandgap reference buffer.
Increasing this capacitor to 100nF will improve power
supply rejection, but at the cost of slower turn-on settling
time. All noise and turn-on settling time specifications
assume that the VREF bypass capacitor is 10nF. Low cost,
low ESR ceramic capacitors such as the X5R and X7R
dielectric material types are recommended.
The bandgap reference is trimmed and buffered to obtain
0.75V typically at the LFB pin with respect to AGND while
the LDO is operating. VVREF is the reference voltage for LFB,
so VVREF will be equal to VLFB within the offset error of the
LDO feedback error amplifier. The bandgap reference and
reference buffer are powered from the greater of V VSYS
(derived from VAD, when present) and VBAT (the battery
voltage). The PSRRREF specification is with respect to VBAT.
It is evaluated while the charging adapter is not present.
24
SC908
Applications Information (continued)
VREF power supply rejection with respect to VAD will be
similar.
improving overall load transient response, and may also
improve input supply rejection.
The VREF pin is a high impedance source. Any load on
VREF will degrade LDO and switching regulator voltage
accuracy. Note that the 10MΩ impedance of a typical
oscilloscope probe is not large enough to prevent loading
of the VREF pin.
Switching Regulator
LDO Power Supply Rejection
Power supply rejection must be considered with respect
to two inputs. The buffered bandgap reference is powered
by the greater of two possible sources, VVSYS (an internal/
external supply voltage, derived from VAD when present)
and VBAT. The LDO is powered from the LVIN pin. PSRRL is
defined as the power supply rejection from LVIN to LVOUT
with the reference and reference buffer powered from BAT
as DC voltage. The reference voltage VREF power supply
rejection specification (PSRRREF) is with respect to BAT. Any
reference voltage power supply noise or ripple is seen in
the LDO as noise on the LFB reference voltage. This noise
is then gained-up to the output by the reciprocal of the
LFB divider network, or by the gain (1 + RL1/RL2).
In the special case VLVIN = VBAT (the LVIN pin is connected
directly to the battery), the power supply rejection of the
LDO, PSRRLBAT, is determined by
PSRRLBAT
PSRR REF
PSRR L
§§ R ·
·
20
20 ¸
20 log10 ¨¨ ¨¨1 L1 ¸¸ u 10
10
¸
© © RL 2 ¹
¹
LDO Current Limit and Short-Circuit Protection
The LDO regulator has current limit circuitry to ensure that
the output current will not damage the device during
output short-circuit to ground, overload, or start-up. The
current limit is guaranteed to be greater than 200mA to
allow fast charging of the output capacitor and for high
transient load currents.
LDO Input and Output Capacitor
A minimum LDO input and output capacitance of 1μF
with a maximum equivalent series resistance (ESR) of less
than 1Ω over temperature is recommended. Increasing
the output capacitance will further reduce output noise
and improve load transient response. A larger input
capacitor will reduce input droop due to load transients,
The SC908 contains a synchronous step-down Pulse Width
Modulated (PWM), DC-DC converter (also referred to as a
Buck Converter or Switcher) with integrated power
devices. The switching frequency is set nominally to
1MHz, allowing the use of small inductors and capacitors.
The current limit of the internal PMOS switch (ILIM_P), allows
a DC output current of at least 150mA with appropriate
external components. For maximum efficiency over the
full load range, the switcher will automatically operate in
Power Save (PSAVE) mode with light loads, and in PWM
(normal switching) mode for heavier loads.
The voltage feedback loop uses an external feedback
divider. An internal synchronous NMOS low side switch is
used. An external Schottky diode on the LX pin is not
required.
Switcher Programmable Output Voltage
The buck converter regulates its output to obtain 0.5V at
the SFB pin. The output can be programmed to any
voltage from 1.0V to 3.0V by an external resistor divider
network from the external circuit node SVOUT to the SFB
pin. The equation for setting the output voltage is
969287
96)%
56
56 SFB is a high impedance input, therefore the magnitude
of resistances used will be determined by a trade off
between feedback network current and product design
practice. A 25pF feedback capacitor, designated CSFB, is
required for stability in PWM mode.
When considering the effect of buck converter load
current on performance specifications, the current flowing
in the feedback divider network should be included in the
load. In most situations, PSAVE mode operation will
require a capacitor from SFB to AGND. Refer to the PSAVE
mode description.
Switcher Power Save (PSAVE) Mode Operation
The PSAVE mode is automatically activated or deactivated
with light to heavy loads, maximizing efficiency across the
25
SC908
Applications Information (continued)
full load range. The SC908 automatically detects the load
current at which it should enter PSAVE mode. This detection is based on the minimum peak current in the PMOS
high side switch in PWM mode. This will vary with input
voltage, output voltage, and the converter external
inductance (LS). PSAVE entry DC load current will decrease
with decreasing LS.
In a PSAVE mode burst cycle, VSVOUT rises from a lower to
an upper voltage threshold with a switching burst (see
Figure 3). Within the burst, the PMOS switch is turned on
until the PMOS current reaches a current limit. It is then
turned off for a fixed duration, and then turned on again
(cycle may be repeated). The low-side NMOS switch is
turned on whenever the high-side switch is off. When the
upper threshold (1.5% above the programmed regulation
voltage) is reached, the switching burst is halted. This
reduces the quiescent current by turning off both highside and low-side switches. VSVOUT decays to the lower
threshold (0.8% above the programmed regulation
voltage) due to the load current discharging the output
capacitor, which initiates another switching burst. The
burst-time to off-time ratio in PSAVE will decrease with
decreasing load current.
PSAVE Mode at
Moderate Load
BURST
OFF
BURST
The SC908 automatically detects when to exit PSAVE
mode by monitoring VSFB, and thus VSVOUT. If the switching
burst output current is insufficient to supply the output
load, VSVOUT will not rise to the upper threshold during a
switching burst, but will instead decrease. If VSVOUT droops
to 2% below the programmed regulation voltage, PSAVE
mode will be deactivated, and the buck converter will
revert immediately to PWM mode. To prevent rapid PWM/
PSAVE mode cycling, the PSAVE entry and exit criteria are
chosen to provide load hysteresis. After reverting to PWM
mode the switcher will remain in PWM mode for 128
switching cycles (approximately 128μs) before it is permitted to re-enter PSAVE mode.
Proper operation of PSAVE mode requires the addition of
a capacitor from the SFB pin to ground, designated CSFG, of
value
CSFG = CSFB × RS1 / RS2.
Switcher Efficiency
Higher Load
Applied
PSAVE Mode at
High Load
OFF
BURST
PWM Mode at
High Load
PWM Mode
+1.6%
VSVOUT
lope frequency will exceed 20kHz for any load greater
than 3mA, if external component recommendations have
been followed. The envelope minimum frequency will
decrease with increasing CSVOUT capacitance.
+0.8%
Prog’d
Voltage
-2%
Inductor
Current
0A
Time
Switcher efficiency is affected by input voltage, output
voltage, temperature, and choice of inductor. It also varies
with load, and on which mode, PWM or PSAVE, is active.
The mode selection depends not only on the instantaneous load, but also on the immediate past load, since
transitions between PSAVE and PWM modes are load
dependent, with hysteresis.
For high loads (those that unconditionally place the
switcher in PWM mode), the efficiency typically exceeds
90%. For low loads (those that unconditionally place the
switcher in PSAVE mode), efficiency can vary from 88 to
92% over all conditions. As the load decreases further, the
SC908 quiescent current eventually becomes significant,
and efficiency drops off sharply.
Figure 3 Power Save Operation
The PSAVE switching burst is designed so that the inductor current ripple is similar to that of PWM mode. To
prevent audible noise, the PSAVE mode parameters have
been chosen such that the minimum PSAVE burst enve-
At intermediate modes, the switcher could select either
PSAVE or PWM mode depending on whether the recent
past load was higher or lower, due to load hysteresis.
Within the hysteresis load range, efficiency can vary from
86% to 92%, over all conditions.
26
SC908
Applications Information (continued)
Switcher Protection Features
The protection features are:
•
•
•
Current limit
Over-voltage protection
Soft-start
Current Limit
The PMOS power device in the buck switcher stage is protected by a current limit function. If a short to ground on
the output occurs, the part enters frequency foldback
mode, which causes the switching frequency to divide by
a factor determined by the output voltage. This prevents
the inductor current from stair-casing.
Over-Voltage Protection
In the event of over-voltage on the output in PWM mode,
the PWM drive is disabled. When disabled, the SLX output
becomes high impedance (both high-side and low-side
switches are turned off ). The switcher will not resume
switching until the output voltage has fallen to 2% below
the programmed regulation voltage.
Soft-Start
The soft-start mode is enabled after every shutdown cycle
to limit in-rush current. This controls the maximum current
during start-up. The PMOS current limit is stepped up
using three soft-start levels to the full value by a timer
driven from the internal oscillator. During soft-start, the
switching frequency is stepped by 1/8, 1/4, and 1/2 of the
internal oscillator frequency up to the full value, under
control of three output voltage thresholds. When the
output voltage rises to 98% of the regulation voltage, softstart mode is disabled.
Switcher External Components
The SC908 is designed for use with the inductor LS = 4.7μH,
although other values can be used. The magnitude of the
inductor current ripple is dependent on the inductor value
and can be determined by the equation
'ILS
VSVOUT
L S u fosc
§ VSVOUT ·
¸
¨¨1 VVOUT ¸¹
©
This equation demonstrates the relationship between
input voltage, output voltage, and inductor ripple
current.
The inductor should have a low DCR to minimize the conduction losses and maximize efficiency. As a minimum
requirement, the DC current rating of the inductor should
be equal to the maximum load current plus half of the
inductor current ripple as shown by the equation
IL S (Peak )
IOUT(MAX ) 'IL S
2
Final inductor selection will depend on various design
considerations such as efficiency, EMI, PSAVE entry, size
and cost.
CBAT Selection
CBAT functions as both the charger output capacitor and as
the switching regulator input capacitor. The source input
current to a buck converter is non-continuous. To prevent
large input voltage ripple a low ESR ceramic capacitor is
required. A minimum value of 10μF should be used for
sufficient input voltage filtering and a 22μF should be
used for improved input voltage filtering.
CSVOUT Selection
The internal compensation is designed to operate with a
minimum output capacitor value of 10μF. Larger output
capacitor values will improve transient performance.
Output voltage ripple is a combination of the voltage
ripple from the inductor current charging and discharging
the output capacitor and the voltage created from the
inductor current ripple through the output capacitor ESR.
Selecting an output capacitor with a low ESR will reduce
the output voltage ripple component, as can be seen in
the equation
'VSVOUT (ESR )
'ILS ( ripple ) u ESR CSVOUT
Capacitors with X7R or X5R ceramic dielectric are recommended for their low ESR and superior temperature and
voltage characteristics. Y5V capacitors should not be used
as their temperature coefficients make them unsuitable
for this application.
When selecting an output capacitor, it is essential that
CSVOUT capacitance be evaluated at the VSVOUT programmed
voltage. The specified capacitance of 0402, and even
0603, package size devices is often severely derated at just
27
SC908
Applications Information (continued)
a few volts of bias. This is especially true of inexpensive
dielectrics. Insufficient SVOUT capacitance can cause
rapid decay of output voltage between PSAVE bursts,
resulting in poor low-load efficiency, PSAVE/PWM mode
cycling, and other erratic behaviors.
Switcher Grounding and PCB Layout Considerations
Poor layout can degrade the performance of the DC-DC
converter and can contribute to EMI problems, ground
bounce and resistive voltage losses. Poor regulation and
instability can result.
A few simple design rules can be implemented to ensure
good layout:
•
•
•
•
Place the inductor and filter capacitors as close
to the device as possible and use short wide
traces between the power components.
Route the output voltage feedback path away
from the inductor and LX node to minimize
noise and magnetic interference.
Maximize ground metal on the component side
to improve the return connection and thermal
dissipation. Separation between the SLX node
and GND should be maintained to avoid coupling of switching noise to the ground plane.
Use a ground plane with several vias connecting
to the component side ground to further reduce
noise interference on sensitive circuit nodes.
Charger Grounding and PCB Layout Considerations
While layout for linear devices is generally not as critical as
for a switching application, careful attention to detail will
ensure reliable operation.
•
•
•
•
•
•
Attaching the part to a larger copper footprint
will enable better heat transfer from the device,
especially on PCBs with internal ground and
power planes.
Place the input, output and bypass capacitors
close to the device for optimal transient response
and device behavior.
Connect all ground connections directly to the
ground plane. If there is no ground plane,
connect to a common local ground point before
connecting to board ground.
The DGND pin and PGND pin should be connected directly to the PCB ground plane as close
to the part as possible. The thermal pad should
be connected to the ground plane with thermal
vias under the SC908.
The nodes indicated as AGND in the Block
Diagram should be connected together and to
the AGND pin. The AGND pin should be tied to
the DGND pin at a single point close to the
SC908.
Route the BSEN trace directly to the battery positive terminal connection on the PCB.
28
SC908
Outline Drawing — MLPQ-24 4x4
A
D
B
PIN 1
INDICATOR
(LASER MARK)
E
A2
DIMENSIONS
MILLIMETERS
INCHES
DIM
MIN NOM MAX MIN NOM MAX
A .031 .035 .039 0.80 0.90 1.00
A1 .000 .001 .002 0.00 0.02 0.05
(.008)
(0.20)
A2
.010
0.18
0.25
.012
b
0.30
.007
D .152 .157 .163 3.85 4.00 4.15
D1 .100 .106 .110 2.55 2.70 2.80
E .152 .157 .163 3.85 4.00 4.15
E1 .100 .106 .110 2.55 2.70 2.80
e
0.50 BSC
.020 BSC
L
.012 .016 .020 0.30 0.40 0.50
N
24
24
aaa
0.10
.004
.004
0.10
bbb
A
SEATING
PLANE
aaa C
A1
C
D1
LxN
E/2
E1
2
1
N
bxN
e
bbb
C A B
D/2
NOTES:
1. CONTROLLING DIMENSIONS ARE IN MILLIMETERS (ANGLES IN DEGREES).
2.
COPLANARITY APPLIES TO THE EXPOSED PAD AS WELL AS THE TERMINALS.
29
SC908
Land Pattern — MLPQ-24 4x4
K
DIMENSIONS
DIM
(C)
G
H
Z
C
G
H
K
P
X
Y
Z
INCHES
(.156)
.122
.106
.106
.020
.010
.033
.189
MILLIMETERS
(3.95)
3.10
2.70
2.70
0.50
0.25
0.85
4.80
X
P
NOTES:
1. THIS LAND PATTERN IS FOR REFERENCE PURPOSES ONLY.
CONSULT YOUR MANUFACTURING GROUP TO ENSURE YOUR
COMPANY'S MANUFACTURING GUIDELINES ARE MET.
2.
THERMAL VIAS IN THE LAND PATTERN OF THE EXPOSED PAD
SHALL BE CONNECTED TO A SYSTEM GROUND PLANE.
FAILURE TO DO SO MAY COMPROMISE THE THERMAL AND/OR
FUNCTIONAL PERFORMANCE OF THE DEVICE.
Contact Information
Semtech Corporation
Power Management Products Division
200 Flynn Road, Camarillo, CA 93012
Phone: (805) 498-2111 Fax: (805) 498-3804
www.semtech.com
30