www.ti.com TVP5154 4-CHANNEL LOW-POWER PAL/NTSC/SECAM VIDEO DECODER WITH INDEPENDENT SCALERS AND FAST LOCK SLES163A – MARCH 2006 – REVISED JULY 2006 1 Introduction 1.1 Features • • • • • • • Four Separate Video Decoder Channels With Features for Each Channel: – Accept NTSC (M, 4.43), PAL (B, D, G, H, I, M, N), and SECAM (B, D, G, K, K1, L) Video Data – Support ITU-R BT.601 Standard Sampling – High-Speed 9-Bit Analog-to-Digital Converter (ADC) – Two Composite Inputs or One S-video Input (for Each Channel) – Fully Differential CMOS Analog Preprocessing Channels With Clamping and Automatic Gain Control (AGC) for Best Signal to Noise (SNR) Performance – Brightness, Contrast, Saturation, Hue, and Sharpness Control Through Inter-Integrated Circuit (I2C) – Complementary 4-Line (3-H Delay) Adaptive Comb Filters for Both Cross-Luminance and Cross-Chrominance Noise Reduction – Patented Architecture for Locking to Weak, Noisy, or Unstable Signals Four Independent Polymorphic Scalers Single or Concurrent Scaled and Unscaled Outputs Via Dual Clocking Data, Interleaved 54-MHz Data or Single 27-MHz Clock Scaled/Unscaled Image Toggle Mode Gives Variable Field Rate for Both Scaled and Unscaled Video Low Power Consumption: 700 mW Typical 128-Pin Thin Quad Flat Pack (TQFP) Package Single 14.31818-MHz Crystal for All Standards and All Channels 1.2 • • • • • • • • Internal Phase-Locked Loop (PLL) for Line-Locked Clock (Separate for Each Channel) and Sampling Sub-Carrier Genlock Output for Synchronizing Color Sub-Carrier of External Encoder Standard Programmable Video Output Format – ITU-R BT.656, 8-Bit 4:2:2 With Embedded Syncs – 8-Bit 4:2:2 With Discrete Syncs Advanced Programmable Video Output Formats – 2× Over-Sampled Raw Vertical Blanking Interval (VBI) Data During Active Video – Sliced VBI Data During Horizontal Blanking or Active Video VBI Modes Supported: – Teletext (NABTS, WST) – Closed-Caption Decode With FIFO, and Extended Data Services (EDS) – Wide Screen Signaling (WSS), Video Program System (VPS), Copy Generation Management System (CGMS), Vertical Interval Time Code (VITC) – Gemstar 1×/2× Electronic Program Guide Compatible Mode – Custom Configuration Mode Allows User to Program the Slice Engine for Unique VBI Data Signals Improved Fast Lock Mode Can Be Used When Input Video Standard Is Known and Signals on Switching Channels Are Clean Four Possible I2C Addresses Allowing 16 Decoder Channels on a Single I2C Bus Applications The following is a partial list of suggested applications: – Security Camera Systems – Large Format Video Wall Displays – Games Systems Please be aware that an important notice concerning availability, standard warranty, and use in critical applications of Texas Instruments semiconductor products and disclaimers thereto appears at the end of this document. PowerPAD is a trademark of Texas Instruments. PRODUCTION DATA information is current as of publication date. Products conform to specifications per the terms of the Texas Instruments standard warranty. Production processing does not necessarily include testing of all parameters. Copyright © 2006–2006, Texas Instruments Incorporated TVP5154 4-CHANNEL LOW-POWER PAL/NTSC/SECAM VIDEO DECODER WITH INDEPENDENT SCALERS AND FAST LOCK www.ti.com SLES163A – MARCH 2006 – REVISED JULY 2006 1.3 Description The TVP5154 device is a 4-channel, low-power, NTSC/PAL/SECAM video decoder. Available in a space-saving 128-pin thin quad flat pack (TQFP) package, each channel of the TVP5154 decoder converts NTSC, PAL, or SECAM video signals to 8-bit ITU-R BT.656 format. Discrete syncs are also available. All four channels of the TVP5154 are independently controllable. The decoders share one crystal for all channels and for all supported standards. The TVP5154 can be programmed using a single inter-integrated circuit (I2C) serial interface. The decoder uses a 1.8-V supply for its analog and digital supplies, and a 3.3-V supply for its I/O. The optimized architecture of the TVP5154 decoder allows for low power consumption. The decoder consumes less than 720 mW of power in typical operation. Each channel of the TVP5154 is an independent video decoder with a programmable polymorphic scaler. Each channel converts baseband analog video into digital YCbCr 4:2:2 component video, which can then be scaled down to any resolution to 1/256 vertical and 15-bit horizontal in 2-pixel decrements. Composite and S-video inputs are supported. Each channel includes one 9-bit analog-to-digital converter (ADC) with 2× sampling. Sampling is ITU-R BT.601 (27.0) MHz, generated from a single 14.31818-MHz crystal or oscillator input) and is line locked. The output formats can be 8-bit 4:2:2 with discrete syncs or 8-bit ITU-R BT.656 with embedded synchronization. The TVP5154 utilizes Texas Instruments patented technology for locking to weak, noisy, or unstable signals. A real-time control (RTC) output is generated for each channel for synchronizing downstream video encoders. Complementary 4-line adaptive comb filtering is available per channel for both the luma and chroma data paths to reduce both cross-luma and cross-chroma artifacts. A chroma trap filter also is available. An improved fast lock mode can be used when the input video standard is known and the signals on the switching channels are clean. Note, switching from snow and/or noisy channels to good channels takes longer. In fast lock mode, video lock is achieved in three fields or less. Video characteristics, including hue, contrast, brightness, saturation, and sharpness, may be independently programmed for each channel using the industry standard I2C serial interface. The TVP5154 generates synchronization, blanking, lock, and clock signals in addition to digital video outputs for each channel. The TVP5154 includes methods for advanced vertical blanking interval (VBI) data retrieval. The VBI data processor slices, parses, and performs error checking on teletext, closed caption, and other data in several formats. I2C commands can be sent to one or more decoder cores simultaneously, reducing the amount of I2C activity necessary to configure each core. A register controls which decoder core receives I2C commands, and can be configured such that all four decoders receive commands at the same time. The main blocks for each of the channels of the TVP5154 decoder include: • Robust sync detector • ADC with analog processor • Y/C separation using 4-line adaptive comb filter • Independent, concurrent scaler outputs • Chrominance processor • Luminance processor • Video clock/timing processor and power-down control • I2C interface • VBI data processor 2 Introduction Submit Documentation Feedback TVP5154 4-CHANNEL LOW-POWER PAL/NTSC/SECAM VIDEO DECODER WITH INDEPENDENT SCALERS AND FAST LOCK www.ti.com SLES163A – MARCH 2006 – REVISED JULY 2006 1.3.1 Related Products • • • • • • TVP5150 TVP5150AM1 TVP5145 TVP5146 TVP5147 TVP5160 1.3.2 Ordering Information abc TA 0°C to 70°C Submit Documentation Feedback PACKAGED DEVICES 128-PIN TQFP-PowerPAD™ PACKAGE OPTION TVP5154PNP Tray TVP5154PNPR Tape and reel Introduction 3 TVP5154 4-CHANNEL LOW-POWER PAL/NTSC/SECAM VIDEO DECODER WITH INDEPENDENT SCALERS AND FAST LOCK www.ti.com SLES163A – MARCH 2006 – REVISED JULY 2006 OUTPUT FORMATTER 2 Functional Block Diagram AIP1B M U X 9−Bit A/D AGC LUMINANCE PROCESSING SCALER CHROMINANCE PROCESSING OUTPUT FORMATTER AIP1A Y/C SEPARATION VBI SLICER AIP2B M U X 9−Bit A/D AGC LUMINANCE PROCESSING SCALER CHROMINANCE PROCESSING OUTPUT FORMATTER AIP2A Y/C SEPARATION VBI SLICER AIP3B M U X 9−Bit A/D AGC LUMINANCE PROCESSING SCALER CHROMINANCE PROCESSING OUTPUT FORMATTER AIP3A Y/C SEPARATION VBI SLICER AIP4B M U X 9−Bit A/D AGC SCL SDA SCALER CHROMINANCE PROCESSING I2C INTERFACE HOST PROCESSOR XIN/OSC LUMINANCE PROCESSING PLL XOUT CH2_OUT [7:0] YCBCR 8−Bit 4:2:2 CH3_OUT [7:0] YCBCR 8−Bit 4:2:2 CH4_OUT [7:0] YCBCR 8−Bit 4:2:2 FID/GLCO[1−4] SYNC PROCESSOR AIP4A Y/C SEPARATION VBI SLICER CH1_OUT [7:0] YCBCR 8−Bit 4:2:2 VSYNC/PAL[1−4] INTERQ/GPCL/BLK[1−4] HSYNC[1−4] AVID[1−4] CLK[1−4] SCLK[1−4] Figure 2-1. Functional Block Diagram 4 Functional Block Diagram Submit Documentation Feedback TVP5154 4-CHANNEL LOW-POWER PAL/NTSC/SECAM VIDEO DECODER WITH INDEPENDENT SCALERS AND FAST LOCK www.ti.com SLES163A – MARCH 2006 – REVISED JULY 2006 3 Terminal Assignments 128 127 126 125 124 123 122 121 120 119 118 117 116 115 114 113 112 111 110 109 108 107 106 105 104 103 102 101 100 99 98 97 AGND AVDD REFP1 REFM1 XIN/OSC XOUT PDN RESETB SCL SDA I2CA0 I2CA1 DGND DVDD IOVDD IOGND CH1_OUT0 CH1_OUT1 CH1_OUT2 CH1_OUT3 CH1_OUT4 CH1_OUT5 CH1_OUT6 CH1_OUT7 SCLK1 CLK1 INT1/GPCL1/VBLK1 AVID1 HSYNC1 DGND DVDD IOVDD 3.1 Pinout 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 TVP5154 128−Pin TQFP Package (Top View) 96 95 94 93 92 91 90 89 88 87 86 85 84 83 82 81 80 79 78 77 76 75 74 73 72 71 70 69 68 67 66 65 IOGND VSYNC1/PALI1 FID1/GLCO1 CH2_OUT0 CH2_OUT1 CH2_OUT2 CH2_OUT3 CH2_OUT4 CH2_OUT5 CH2_OUT6 CH2_OUT7 SCLK2 CLK2 INT2/GPCL2/VBLK2 DGND DVDD IOVDD IOGND AVID2 HSYNC2 VSYNC2/PALI2 FID2/GLCO2 CH3_OUT0 CH3_OUT1 CH3_OUT2 CH3_OUT3 CH3_OUT4 CH3_OUT5 CH3_OUT6 CH3_OUT7 DGND DVDD PLL_VDD PLL_GND AGND TMS FID4/GLCO4 VSYNC4/PALI4 HSYNC4 AVID4 INT4/GPCL4/VBLK4 CLK4 SCLK4 IOGND IOVDD DVDD DGND CH4_OUT7 CH4_OUT6 CH4_OUT5 CH4_OUT4 CH4_OUT3 CH4_OUT2 CH4_OUT1 CH4_OUT0 FID3/GLCO3 VSYNC3/PALI3 HSYNC3 AVID3 INT3/GPCL3/VBLK3 CLK3 SCLK3 IOGND IOVDD 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 AI1GND AIP1A AIP1B PLL_VDD PLL_GND REFM2 REFP2 AVDD AGND AI2GND AIP2A AIP2B PLL_VDD PLL_GND AVDD AGND REFM3 REFP3 AVDD AGND AI3GND AIP3A AIP3B PLL_VDD PLL_GND REFM4 REFP4 AVDD AGND AI4GND AIP4A AIP4B Submit Documentation Feedback Terminal Assignments 5 TVP5154 4-CHANNEL LOW-POWER PAL/NTSC/SECAM VIDEO DECODER WITH INDEPENDENT SCALERS AND FAST LOCK www.ti.com SLES163A – MARCH 2006 – REVISED JULY 2006 3.2 Terminal Functions TERMINAL NAME NO. I/O DESCRIPTION Analog Section AIP1A AIP1B 2 3 I Analog inputs for Channel 1. Connect to the video analog input via a 0.1-µF capacitor. The maximum input range is 0–0.75 VPP, and may require an attenuator to reduce the input amplitude to the desired level. If not used, connect to AGND via a 0.1-µF capacitor. Refer to the schematic in Section 12. AIP2A AIP2B 11 12 I Analog inputs for Channel 2. Connect to the video analog input via a 0.1-µF capacitor. The maximum input range is 0-0.75 VPP, and may require an attenuator to reduce the input amplitude to the desired level. If not used, connect to AGND via a 0.1-µF capacitor. Refer to the schematic in Section 12. AIP3A AIP3B 22 23 I Analog inputs for Channel 3. Connect to the video analog input via a 0.1-µF capacitor. The maximum input range is 0-0.75 VPP, and may require an attenuator to reduce the input amplitude to the desired level. If not used, connect to AGND via a 0.1-µF capacitor. Refer to the schematic in Section 12. AIP4A AIP4B 31 32 I Analog inputs for Channel 4. Connect to the video analog input via a 0.1-µF capacitor. The maximum input range is 0-0.75 VPP, and may require an attenuator to reduce the input amplitude to the desired level. If not used, connect to AGND via a 0.1-µF capacitor. Refer to the schematic in Section 12. AVDD 8, 15, 19, 28, 127 P Analog power supply. Connect to 1.8-V analog supply. AGND 9, 16, 20, 29, 35, 128 P Analog power supply return. Connect to analog ground. AIxGND 1, 10, 21, 30 P Analog input signal return. Connect to analog ground. PLL_GND 5, 14, 25, 34 P PLL power supply return. Connect to analog ground. PLL_VDD 4, 13, 24, 33 P PLL power supply. Connect to 1.8-V analog supply. REFMx 6, 17, 26, 125 I Reference supply decoupling . Connect to analog ground through a 1-µF capacitor. Connect to REFPx through a 1-µF capacitor. REFPx 7, 18, 27, 126 I Reference supply decoupling . Connect to analog ground through a 1-µF capacitor. Connect to REFMx through a 1-µF capacitor. DGND 47, 66, 82, 99, 116 P Digital power supply return. Connect to digital ground DVDD 46, 65, 81, 98, 115 P Digital power supply. Connect to 1.8-V digital supply. IOGND 44, 63, 79, 96, 113 P I/O power supply return. Connect to digital ground. IOVDD 45, 64, 80, 97, 114 P I/O power supply. Connect to 3.3-V digital supply FID1/GLCO1 FID2/GLCO2 FID3/GLCO3 FID4/GLCO4 94 75 56 37 O 1. FID: Odd/even field indicator or vertical lock indicator. For the odd/even indicator, a 1 indicates the odd field. 2. GLCO: This serial output carries color PLL information. A slave device can decode the information to allow chroma frequency control from the TVP5154 decoder. Data is transmitted at the CLK rate in Genlock mode. AVID1 AVID2 AVID3 AVID4 101 78 59 40 O Active video indicator. This signal is high during the horizontal active time of the video output. INTREQ1/GPCL1/VBLK1 INTREQ2/GPCL2/VBLK2 INTREQ3/GPCL3/VBLK3 INTREQ4/GPCL4/VBLK4 102 83 60 41 I/O 1. Interrupt request : Open drain when active low. Digital Section 2. GPCL: General-purpose output. In this mode, the state of GPCL is directly programmed via I2C. 3. VBLK: Vertical blank output. In this mode, the GPCL terminal is used to indicate the VBI of the output video. The beginning and end times of this signal are programmable via I2C. 6 Terminal Assignments Submit Documentation Feedback TVP5154 4-CHANNEL LOW-POWER PAL/NTSC/SECAM VIDEO DECODER WITH INDEPENDENT SCALERS AND FAST LOCK www.ti.com SLES163A – MARCH 2006 – REVISED JULY 2006 TERMINAL NAME HSYNC1 HSYNC2 HSYNC3 HSYNC4 NO. I/O DESCRIPTION 100 77 58 39 O Horizontal synchronization 95 76 57 38 O 1. VSYNC: Vertical synchronization 2. PALI: PAL line indicator or horizontal lock indicator. For the PAL line indicator, a 1 indicates a noninverted line, and a 0 indicates an inverted line. PDN 122 I Power down (active low). A 0 on this pin puts the decoder in standby mode. PDN preserves the value of the registers. RESETB 121 I Active-low reset. RESETB can be used only when PDN = 1. When RESETB is pulled low, it resets all the registers and restarts the internal microprocessor. SCL 120 I/O I2C serial clock (open drain) SDA 119 I/O I2C serial data (open drain) I2CA0 118 I During power-on reset, this pin is sampled along with pin 117 (I2CA1) to determine the I2C address the device is configured to. A 10-kΩ resistor should pull this either high (to IOVDD) or low to select different I2C device addresses. I2CA1 117 I During power-on reset, this pin is sampled along with pin 118 (I2CA0) to determine the I2C address the device is configured to. A 10-kΩ resistor should pull this either high (to IOVDD) or low to select different I2C device addresses. CLK1 CLK2 CLK3 CLK4 103 84 61 42 O Unscaled system data clock at either 27 MHz or 54 MHz SCLK1 SCLK2 SCLK3 SCLK4 104 85 62 43 O Scaled system data clock at 27 MHz. This signal can be used to qualify scaled/unscaled data when the unscaled system data clock is set to 54 MHz. XIN/OSC XOUT 124 123 I O External clock reference. The user may connect XIN to an oscillator or to one terminal of a crystal oscillator. The user may connect XOUT to the other terminal of the crystal oscillator or not connect XOUT at all. One single 14.31818-MHz crystal or oscillator is needed for ITU-R BT.601 sampling, for all supported standards. CH1_OUT[7:0] 105–112 O Decoded ITU-R BT.656 output/YCbCr 4:2:2 output with discrete sync for channel 1 CH2_OUT[7:0] 86–93 O Decoded ITU-R BT.656 output/YCbCr 4:2:2 output with discrete sync for channel 2 CH3_OUT[7:0] 67–74 O Decoded ITU-R BT.656 output/YCbCr 4:2:2 output with discrete sync for channel 3 CH4_OUT[7:0] 48–55 O Decoded ITU-R BT.656 output/YCbCr 4:2:2 output with discrete sync for channel 4 36 I Test-mode select. This pin should be connected to digital ground for correct device operation. VSYNC1 VSYNC2 VSYNC3 VSYNC4 TMS /PALI1 /PALI2 /PALI3 /PALI4 4 Functional Description 4.1 Analog Front End Each channel of the TVP5154 decoder has an analog input channel that accepts two video inputs, which should be ac coupled through 0.1-µF capacitors. The decoder supports a maximum input voltage range of 0.75 V; therefore, an attenuation of one-half is needed for standard input signals with a peak-to-peak variation of 1.5 V. The maximum parallel termination before the input to the device is 75 Ω. Refer to schematic at the end of this document for recommended configuration. The two analog input ports can be connected as follows: • Two selectable composite video inputs or • One S-video input An internal clamping circuit restores the ac-coupled video signal to a fixed dc level. The programmable gain amplifier (PGA) and the automatic gain control (AGC) circuit work together to ensure that the input signal is amplified or attenuated correctly, ensuring the proper input range for the ADC. Submit Documentation Feedback Functional Description 7 TVP5154 4-CHANNEL LOW-POWER PAL/NTSC/SECAM VIDEO DECODER WITH INDEPENDENT SCALERS AND FAST LOCK www.ti.com SLES163A – MARCH 2006 – REVISED JULY 2006 When switching CVBS inputs from one input to the other, the AGC settings are internally stored and the previous settings for the new input are restored. This eliminates flashes and dark frames associated with switching between inputs that have different signal amplitudes. The ADC has nine bits of resolution and runs at a maximum speed of 27 MHz. The clock input for the ADC comes from the PLL. 4.2 Composite Processing Block Diagram The composite processing block processes NTSC/PAL/SECAM signals into the YCbCr color space. Figure 2-1 shows the basic architecture of this processing block. Figure 2-1 shows the luminance/chrominance (Y/C) separation process in the TVP5154 decoders. The composite video is multiplied by sub-carrier signals in the quadrature modulator to generate the color difference signals Cb and Cr. Cb and Cr are then low pass (LP) filtered to achieve the desired bandwidth and to reduce crosstalk. An adaptive 4-line comb filter separates CbCr from Y. Chroma is remodulated through another quadrature modulator and subtracted from the line-delayed composite video to generate luma. Contrast, brightness, hue, saturation, and sharpness (using the peaking filter) are programmable via I2C. The Y/C separation is bypassed for S-video input. For S-video, the remodulation path is disabled. 4.3 Adaptive Comb Filtering The 4-line comb filter can be selectively bypassed in the luma or chroma path. If the comb filter is bypassed in the luma path, chroma notch filters are used. TI’s patented adaptive 4-line comb filter algorithm reduces artifacts, such as hanging dots at color boundaries, and detects and properly handles false colors in high-frequency luminance images, such as a multiburst pattern or circle pattern. 4.4 Color Low-Pass Filter In some applications, it is desirable to limit the Cb/Cr bandwidth to avoid crosstalk. This is especially true in the case of video signals that have asymmetrical Cb/Cr sidebands. The color LP filters provided limit the bandwidth of the Cb/Cr signals. Color LP filters are needed when the comb filtering turns off, due to extreme color transitions in the input image. Refer to Chrominance Control #2 Register, for the response of these filters. The filters have three options that allow three different frequency responses based on the color frequency characteristics of the input video. 4.5 Luminance Processing The luma component is derived from the composite signal by subtracting the remodulated chroma information. A line delay exists in this path to compensate for the line delay in the adaptive comb filter in the color processing chain. The luma information is then fed into the peaking circuit, which enhances the high-frequency components of the signal, thus, improving sharpness. 4.6 Chrominance Processing For NTSC/PAL formats, the color processing begins with a quadrature demodulator. The Cb/Cr signals then pass through the gain control stage for chroma saturation adjustment. An adaptive comb filter is applied to the demodulated signals to separate chrominance and eliminate cross-chrominance artifacts. An automatic color-killer circuit is also included in this block. The color killer suppresses the chroma processing when the color burst of the video signal is weak or not present. The SECAM standard is similar to PAL except for the modulation of color, which is FM instead of QAM. 8 Functional Description Submit Documentation Feedback TVP5154 4-CHANNEL LOW-POWER PAL/NTSC/SECAM VIDEO DECODER WITH INDEPENDENT SCALERS AND FAST LOCK www.ti.com SLES163A – MARCH 2006 – REVISED JULY 2006 4.7 Timing Processor The timing processor is a combination of hardware and software running in the internal microprocessor that serves to control horizontal lock to the input sync pulse edge, AGC and offset adjustment in the analog front end, and vertical sync detection. 4.8 VBI Data Processor The TVP5154 VBI data processor (VDP) slices various data services, such as teletext (WST, NABTS), closed caption (CC), wide screen signaling (WSS), etc. These services are acquired by programming the VDP to enable standards in the VBI. The results are stored in a FIFO and/or registers. The teletext results are stored in a FIFO only. Table 4-1 lists a summary of the types of VBI data supported according to the video standard. It supports ITU-R BT. 601 sampling for each. Table 4-1. Data Types Supported by the VDP LINE MODE REGISTER (D0h–FCh) BITS [3:0] NAME DESCRIPTION 0000b WST SECAM Teletext, SECAM 0001b WST PAL B Teletext, PAL, System B 0010b WST PAL C Teletext, PAL, System C 0011b WST, NTSC B Teletext, NTSC, System B 0100b NABTS, NTSC C Teletext, NTSC, System C 0101b NABTS, NTSC D Teletext, NTSC, System D (Japan) 0110b CC, PAL Closed caption PAL 0111b CC, NTSC Closed caption NTSC 1000b WSS, PAL Wide-screen signal, PAL 1001b WSS, NTSC Wide-screen signal, NTSC 1010b VITC, PAL Vertical interval timecode, PAL 1011b VITC, NTSC Vertical interval timecode, NTSC 1100b VPS, PAL Video program system, PAL 1111b Active Video Active video/full field At power up, the host interface is required to program the VDP-configuration RAM (VDP-CRAM) contents with the lookup table (see Section 9.2.63). This is done through port address C3h. Each read from or write to this address auto increments an internal counter to the next RAM location. To access the VDP-CRAM, the line mode registers (D0h–FCh) must be programmed with FFh to avoid a conflict with the internal microprocessor and the VDP in both writing and reading. Full field mode must also be disabled. Available VBI lines are from line 6 to line 27 of both field 1 and field 2. Each line can be any VBI mode. Output data is available either through the VBI-FIFO (B0h) or through dedicated registers at 90h–AFh, both of which are available through the I2C port. 4.9 VBI FIFO and Ancillary Data in Video Stream Sliced VBI data can be output as ancillary data in the video stream in the ITU-R BT.656 mode. VBI data is output during the horizontal blanking period following the line from which the data was retrieved. Table 4-2 shows the header format and sequence of the ancillary data inserted into the video stream. This format is also used to store any VBI data into the FIFO. The size of FIFO is 512 bytes. Therefore, the FIFO can store up to 11 lines of teletext data with the NTSC NABTS standard. Submit Documentation Feedback Functional Description 9 TVP5154 4-CHANNEL LOW-POWER PAL/NTSC/SECAM VIDEO DECODER WITH INDEPENDENT SCALERS AND FAST LOCK www.ti.com SLES163A – MARCH 2006 – REVISED JULY 2006 Table 4-2. Ancillary Data Format and Sequence BYTE NO. D7 (MSB) D6 D5 D4 D3 D2 D1 D0 (LSB) 0 0 0 0 0 0 0 0 0 1 1 1 1 1 1 1 1 1 DESCRIPTION Ancillary data preamble 2 1 1 1 1 1 1 1 1 3 NEP EP 0 1 0 DID2 DID1 DID0 4 NEP EP F5 F4 F3 F2 F1 F0 Secondary data ID (SDID) 5 NEP EP N5 N4 N3 N2 N1 N0 Number of 32 bit data (NN) 6 Video line # [7:0] 7 0 0 0 Data error Match #1 Data ID (DID) Internal data ID0 (IDID0) Match #2 Video line # [9:8] Internal data ID1 (IDID1) 8 1. Data Data byte 9 2. Data Data byte 10 3. Data Data byte 11 4. Data Data byte • • • • • • — 1. Data Data byte m. Data 4(N+2)-1 NEP EP 0 0 0 Nth word Data byte CS[5:0] 0 1st word 0 EP: Even parity for D0–D5 NEP: Negated even parity DID: 91h: Sliced data of VBI lines of first field Check sum 0 0 0 Fill byte 53h: Sliced data of line 24 to end of first field 55h: Sliced data of VBI lines of second field 97h: Sliced data of line 24 to end of second field SDID: This field holds the data format taken from the line mode register of the corresponding line. NN: Number of Dwords beginning with byte 8 through 4(N+2). This value is the number of Dwords where each Dword is 4 bytes. IDID0: Transaction video line number [7:0] IDID1: Bit 0/1 = Transaction video line number [9:8] Bit 2 = Match 2 flag Bit 3 = Match 1 flag Bit 4 = 1 if an error was detected in the EDC block. 0 if not. CS: Sum of D0–D7 of DID through last data byte Fill byte: Fill bytes make a multiple of four bytes from byte 0 to last fill byte. For teletext modes, byte 8 is the sync pattern byte. Byte 9 is 1. Data (the first data byte). 4.10 Raw Video Data Output The TVP5154 decoder can output raw A/D video data at 2× sampling rate for external VBI slicing. This is transmitted as an ancillary data block during the active horizontal portion of the line and during vertical blanking. 10 Functional Description Submit Documentation Feedback TVP5154 4-CHANNEL LOW-POWER PAL/NTSC/SECAM VIDEO DECODER WITH INDEPENDENT SCALERS AND FAST LOCK www.ti.com SLES163A – MARCH 2006 – REVISED JULY 2006 4.11 Output Formatter The output formatter is responsible for generating the output digital video stream. The YCbCr digital output can be programmed as 8-bit 4:2:2 or 8-bit ITU-R BT.656 parallel interface standard. Depending on which output mode is selected, the output for each channel can be unscaled data, scaled data, or both scaled and unscaled data interleaved in various ways. Table 4-3. Summary of Line Frequencies, Data Rates, and Pixel Counts STANDARDS HORIZONTAL LINE RATE (kHz) PIXELS PER LINE ACTIVE PIXELS PER LINE CLK FREQUENCY (MHz) 15.73426 858 720 27.00 NTSC (M, 4.43), ITU-R BT.601 PAL (B, D, G, H, I), ITU-R BT.601 15.625 864 720 27.00 PAL (M), ITU-R BT.601 15.73426 858 720 27.00 PAL (N), ITU-R BT.601 15.625 864 720 27.00 SECAM, ITU-R BT.601 15.625 864 720 27.00 4.12 Synchronization Signals External (discrete) syncs are provided via the following signals: • VSYNC (vertical sync) • FID/VLK (field indicator or vertical lock indicator) • GPCL/VBLK (general-purpose I/O or vertical blanking indicator) • PALI/HLK (PAL switch indicator or horizontal lock indicator) • HSYNC (horizontal sync) • AVID (active video indicator) VSYNC, FID, PALI, and VBLK are software set and programmable to the CLK pixel count. This allows any possible alignment to the internal pixel count and line count. The default settings for a 525-/625-line video output are shown in Figure 4-1. Submit Documentation Feedback Functional Description 11 TVP5154 4-CHANNEL LOW-POWER PAL/NTSC/SECAM VIDEO DECODER WITH INDEPENDENT SCALERS AND FAST LOCK www.ti.com SLES163A – MARCH 2006 – REVISED JULY 2006 525 LINE 525 1 2 3 4 5 6 7 8 9 10 11 20 21 22 Composite Video VSYNC FID GPCL/VBLK ↔ VBLK Stop ↔ VBLK Start 262 263 264 265 266 267 268 269 270 271 272 273 282 283 284 Composite Video VSYNC FID GPCL/VBLK ↔ VBLK Stop ↔ VBLK Start 625 LINE 310 311 312 313 314 315 316 317 318 319 320 333 334 335 336 Composite Video VSYNC FID GPCL/VBLK ↔ VBLK Stop ↔ VBLK Start 622 623 624 625 1 2 3 4 5 6 7 20 21 22 23 Composite Video VSYNC FID GPCL/VBLK ↔ VBLK Start ↔ VBLK Stop Line numbering conforms to ITU-R BT.470. Figure 4-1. 8-Bit 4:2:2, Timing With 2× Pixel Clock (CLK) Reference HSYN HSYN START AVID AV ID STOP AV ID STA RT NOTE: AVID rising edge occurs four CLK cycles early when in ITU-R BT.656 output mode. Figure 4-2. Horizontal Synchronization Signals 12 Functional Description Submit Documentation Feedback TVP5154 4-CHANNEL LOW-POWER PAL/NTSC/SECAM VIDEO DECODER WITH INDEPENDENT SCALERS AND FAST LOCK www.ti.com SLES163A – MARCH 2006 – REVISED JULY 2006 4.13 Active Video (AVID) Cropping AVID cropping provides a means to decrease the amount of video data output. This is accomplished by horizontally blanking a number of AVID pulses and by vertically blanking a number of lines per frame. The horizontal AVID cropping is controlled using registers 11h and 12h for start pixels MSB and LSB, respectively. Registers 13h and 14h provide access to stop pixels MSB and LSB, respectively. The vertical AVID cropping is controlled using the vertical blanking (VBLK) start and stop registers at addresses 18h and 19h. Figure 4-3 shows an AVID application. AVID cropping can be independently controlled for scaled (registers 25h, 26h, 29h, and 2Ah) and unscaled (registers 11h thru 14h) data streams. AVID start and stop must be changed in multiples of two pixels to ensure correct UV alignment. Additionally, AVID start and stop can be configured to include the SAV- and EAV-embedded sync signals or to exclude them, and to either include or exclude ITU656 ancillary data. VBLK Stop Active Video Area AVID Cropped Area VSYNC VBLK Start AVID Start AVID Stop HSYNC Figure 4-3. AVID Application 4.14 Embedded Syncs Standards with embedded syncs insert SAV and EAV codes into the data stream at the beginning and end of horizontal blanking. These codes contain the V and F bits that also define vertical timing. F and V change on EAV. Table 4-4 gives the format of the SAV and EAV codes. H equals 1 always indicates EAV. H equals 0 always indicates SAV. The alignment of V and F to the line and field counter varies depending on the standard. Please refer to ITU-R BT.656 for more information on embedded syncs. The P bits are protection bits: P3 = V x or H P2 = F x or H P1 = F x or V P0 = F x or V x or H Submit Documentation Feedback Functional Description 13 TVP5154 4-CHANNEL LOW-POWER PAL/NTSC/SECAM VIDEO DECODER WITH INDEPENDENT SCALERS AND FAST LOCK www.ti.com SLES163A – MARCH 2006 – REVISED JULY 2006 Table 4-4. EAV and SAV Sequence 8-BIT DATA D7 (MSB) D6 D5 D4 D3 D2 D1 D0 Preamble 1 1 1 1 1 1 1 1 Preamble 0 0 0 0 0 0 0 0 Preamble 0 0 0 0 0 0 0 0 Status word 1 F V H P3 P2 P1 P0 The status word may be modified in order to pass information about whether the current data corresponds to scaled or unscaled data. See register 1Fh for more information. 4.15 Clock and Data Control Figure 4-4 shows a logical schematic of the data and clock control signals. Blank =01 Delay =00 Scaler =11 Data Decoder Field mode(0) Field mode(1) Field mode(2) Field mode(3) Field mode(4) Field mode(5) Field mode(6) Field mode(7) Field mode(8) Field mode(9) Field mode(10) Field mode(11) Field mode(12) Field mode(13) Field mode(14) Field mode(15) =4 01 =1 00 =0 /2 = 27MHz =2/3 Mode SCLK SCLK OE SCLK edge !=3 CLK 54MHz =3 CLK OE Mode CLK edge Figure 4-4. Clock and Data Control 14 Functional Description Submit Documentation Feedback TVP5154 4-CHANNEL LOW-POWER PAL/NTSC/SECAM VIDEO DECODER WITH INDEPENDENT SCALERS AND FAST LOCK www.ti.com SLES163A – MARCH 2006 – REVISED JULY 2006 5 I2C Host Interface The I2C standard consists of two signals, serial input/output data line (SDA) and input/output clock line (SCL), which carry information between the devices connected to the bus. The input pins I2CA0 and I2CA1 are used to select the slave address to which the device responds. Although the I2C system can be multimastered, the TVP5154 decoder functions as a slave device only. Both SDA and SCL must be connected to IOVDD via pullup resistors. When the bus is free, both lines are high. The slave address select terminals (I2CA0 and I2CA1) enable the use of four TVP5154 decoders on the same I2C bus. At the trailing edge of reset, the status of the I2CA0 and I2CA1 lines are sampled to determine the device address used. Table 5-1 summarizes the terminal functions of the I2C-mode host interface. Table 5-2 shows the device address selection options. Table 5-1. I2C Terminal Description SIGNAL TYPE I2CA0 I Slave address selection DESCRIPTION I2CA1 I Slave address selection SCL I/O (open drain) Input/output clock line SDA I/O (open drain) Input/output data line Table 5-2. I2C Host Interface Device Addresses A6 A5 A4 A3 A2 A1 (I2CA1) A0 (I2CA0) R/W HEX 1 0 1 1 1 0 0 1/0 B9/B8 1 0 1 1 1 0 1 1/0 BB/BA 1 0 1 1 1 1 0 1/0 BD/BC 1 0 1 1 1 1 1 1/0 BF/BE Data transfer rate on the bus is up to 400 kbit/s. The number of interfaces connected to the bus is dependent on the bus capacitance limit of 400 pF. The data on the SDA line must be stable during the high period of the SCL, except for start and stop conditions. The high or low state of the data line can only change with the clock signal on the SCL line being low. A high-to-low transition on the SDA line while the SCL is high indicates an I2C start condition. A low-to-high transition on the SDA line while the SCL is high indicates an I2C stop condition. Every byte placed on the SDA must be eight bits long. The number of bytes that can be transferred is unrestricted. Each byte must be followed by an acknowledge bit. The acknowledge-related clock pulse is generated by the I2C master. To simplify programming of each of the four decoder channels, a single I2C write transaction can be transmitted to any one or more of the four cores in parallel. This reduces the time required to download firmware or to configure the device when all channels are to be configured in the same manner. It also enables the addresses for all registers to be common across all decoders. I2C sub-address 0xFE contains four bits, with each bit corresponding to one of the decoder cores. If this bit is set, I2C write transactions are sent to the corresponding decoder core. If the bit is 0, the corresponding decoder does not receive the I2C write transactions. I2C sub-address 0xFF contains four bits, with each bit corresponding to one of the decoder cores. If this bit is set, I2C read transactions are sent to the corresponding decoder core. Note, only one of the bits in this register should be set at a given time, ensuring that only one decoder core is accessed at a time for read operations. If more than one bit is set, the lowest set bit number corresponds to the core that responds to the read transaction. Submit Documentation Feedback I2C Host Interface 15 TVP5154 4-CHANNEL LOW-POWER PAL/NTSC/SECAM VIDEO DECODER WITH INDEPENDENT SCALERS AND FAST LOCK www.ti.com SLES163A – MARCH 2006 – REVISED JULY 2006 Note, when register 0xFE is written to with any value, register 0xFF is set to 0x00. Likewise, when register 0xFF is written to with any value, register 0xFE is set to 0x00. 5.1 I2C Write Operation Data transfers occur utilizing the following illustrated formats. An I2C master initiates a write operation to the TVP5154 decoder by generating a start condition (S) followed by the TVP5154 I2C address (as shown below), in MSB first bit order, followed by a 0 to indicate a write cycle. After receiving an acknowledge from the TVP5154 decoder, the master presents the sub-address of the register, or the first of a block of registers it wants to write, followed by one or more bytes of data, MSB first. The TVP5154 decoder acknowledges each byte after completion of each transfer. The I2C master terminates the write operation by generating a stop condition (P). abc Step 1 0 I2C start (master) S Step 2 7 6 5 4 3 2 1 0 I2C general address (master) 1 0 1 1 1 0 X 0 Step 3 9 I2C acknowledge (slave) A Step 4 I2C write register address (master) 7 6 5 4 3 2 1 0 addr addr addr addr addr addr addr addr Step 5 9 I2C acknowledge (slave) A Step 6 7 6 5 4 3 2 1 0 Data Data Data Data Data Data Data Data I2C write data (master) Step 7 (1) 9 I2C A acknowledge (slave) Step 8 0 I2C P (1) stop (master) Repeat steps 6 and 7 until all data have been written. 5.2 I2C Read Operation The read operation consists of two phases. The first phase is the address phase. In this phase, an I2C master initiates a write operation to the TVP5154 decoder by generating a start condition (S) followed by the TVP5154 I2C address, in MSB first bit order, followed by a 0 to indicate a write cycle. After receiving acknowledges from the TVP5154 decoder, the master presents the sub-address of the register or the first of a block of registers it wants to read. After the cycle is acknowledged, the master terminates the cycle immediately by generating a stop condition (P). The second phase is the data phase. In this phase, an I2C master initiates a read operation to the TVP5154 decoder by generating a start condition followed by the TVP5154 I2C address (as shown below for a read operation), in MSB first bit order, followed by a 1 to indicate a read cycle. After an acknowledge from the TVP5154 decoder, the I2C master receives one or more bytes of data from the TVP5154 decoder. The I2C master acknowledges the transfer at the end of each byte. After the last data byte desired has been transferred from the TVP5154 decoder to the master, the master generates a not acknowledge followed by a stop. 16 I2C Host Interface Submit Documentation Feedback TVP5154 4-CHANNEL LOW-POWER PAL/NTSC/SECAM VIDEO DECODER WITH INDEPENDENT SCALERS AND FAST LOCK www.ti.com SLES163A – MARCH 2006 – REVISED JULY 2006 Read Phase 1 abc Step 1 0 I2C start (master) S Step 2 7 6 5 4 3 2 1 0 I2C general address (master) 1 0 1 1 1 0 X 0 Step 3 9 I2C A 7 6 5 4 3 2 1 0 addr addr addr addr addr addr addr addr acknowledge (slave) Step 4 I2C read register address (master) Step 5 9 I2C A acknowledge (slave) Step 6 0 I2C stop (master) P Read Phase 2 abc Step 7 0 I2C start (master) S Step 8 7 6 5 4 3 2 1 0 I2C 1 0 1 1 1 0 X 1 7 6 5 4 3 2 1 0 Data Data Data Data Data Data Data Data general address (master) Step 9 9 I2C A acknowledge (slave) Step 10 I2C read data (slave) Step 11 (1) 9 I2C not acknowledge (master) A Step 12 0 I2C stop (master) P (1) Repeat steps 10 and 11 for all bytes read. Master does not acknowledge the last read data received. 5.2.1 I2C Timing Requirements The TVP5154 decoder requires delays in the I2C accesses to accommodate its internal processor’s timing. In accordance with I2C specifications, the TVP5154 decoder holds the I2C clock line (SCL) low to indicate the wait period to the I2C master. If the I2C master is not designed to check for the I2C clock line held-low condition, the maximum delays must always be inserted where required. These delays are of variable length; maximum delays are indicated in the following diagram: Table 5-3. I2C Timing Start (1) Slave address (B8h) Ack Subaddress Ack Data (XXh) Ack Wait 128 µs (1) Stop If the SCL pin is not monitored by the master to enable pausing, a delay of 128 µs should be inserted between transactions for registers 00h through 8Fh. Submit Documentation Feedback I2C Host Interface 17 TVP5154 4-CHANNEL LOW-POWER PAL/NTSC/SECAM VIDEO DECODER WITH INDEPENDENT SCALERS AND FAST LOCK www.ti.com SLES163A – MARCH 2006 – REVISED JULY 2006 6 Clock Circuits An internal line-locked PLL generates the system and pixel clocks. A 14.31818-MHz clock is required to drive the PLL. This may be input to the TVP5154 decoder on terminal 124 (XIN), or a crystal of 14.31818-MHz fundamental resonant frequency may be connected across terminals 123 and 124 (XIN and XOUT). Figure 6-1 shows the reference clock configurations. For the example crystal circuit shown (a parallel-resonant crystal with 14.31818-MHz fundamental frequency), the external capacitors must have the following relationship: CL1 = CL2 = 2CL – CSTRAY where CSTRAY is the terminal capacitance with respect to ground. Figure 6-1 shows the reference clock configurations. 14.31818-MHz Crystal 124 14.31818 MHz 1.8-V Clock CL1 124 R 123 123 CL2 Figure 6-1. Clock and Crystal Connectivity 7 Genlock Control and RTC A Genlock control (GLCO) function is provided to support a standard video encoder to synchronize its internal color oscillator for properly reproduced color with unstable timebase sources like VCRs. The frequency control word of the internal color subcarrier digital control oscillator (DTO) and the subcarrier phase reset bit are transmitted via the GLCO terminal. The frequency control word is a 23-bit binary number. The frequency of the DTO can be calculated from the following equation: F F dto + ctrl F clk 223 (1) where Fdto is the frequency of the DTO, Fctrl is the 23–bit DTO frequency control, and Fclk is the frequency of the CLK. 7.1 TVP5154 Genlock Control Interface A write of 1 to bit 4 of the chrominance control register at I2C subaddress 1Ah causes the subcarrier DTO phase reset bit to be sent on the next scan line on GLCO. The active-low reset bit occurs seven CLKs after the transmission of the last bit of DCO frequency control. Upon the transmission of the reset bit, the phase of the TVP5154 internal subcarrier DCO is reset to zero. A Genlock slave device can be connected to the GLCO terminal and uses the information on GLCO to synchronize its internal color phase DCO to achieve clean line and color lock. 7.2 RTC Mode Figure 7-1 shows the timing diagram of the RTC mode. Clock rate for the RTC mode is four times slower than the GLCO clock rate. For PLL frequency control, the upper 22 bits are used. Each frequency control bit is two clock cycles long. The active-low reset bit occurs six CLKs after the transmission of the last bit of PLL frequency control. 18 Clock Circuits Submit Documentation Feedback TVP5154 4-CHANNEL LOW-POWER PAL/NTSC/SECAM VIDEO DECODER WITH INDEPENDENT SCALERS AND FAST LOCK www.ti.com SLES163A – MARCH 2006 – REVISED JULY 2006 CLK GLCO 22 MSB LSB 21 0 >128 CLK 23 CLK 23-Bit Frequency Control 7 CLK 1 CLK 1 CLK Start Bit DCO Reset Bit GLCO Timing M S B RTC L S B 0 21 128 CLK 16 CLK 44 CLK 1 CLK 22-Bit Fsc Frequency Control 2 CLK PAL Switch 2 CLK Start Bit 3 CLK 1 CLK Reset Bit Figure 7-1. RTC Timing 8 Power-Up, Reset, and Power-Down Sequence (Required) Terminals 121 (RESETB) and 122 (PDN) work together to put the TVP5154 decoder into one of three modes. Table 8-1 shows the configuration. After power up, the device is in an unknown state with its outputs undefined until it receives a RESETB active low for at least 200 ns. The power supplies should be active and stable for 10 ms before RESETB becomes inactive. There are no power-sequencing requirements, except that all power supplies should become active and stable within 500 ms of each other. After each power-up and hardware reset, this procedure must be followed: 1. Wait at least 1 ms. Each decoder must be started by writing 0x00h to register 7Fh for all four decoders. 2. Wait at least 1 ms. Check the status of the TVP5154 by doing an I2C read of the version number, register 81h, for all four decoders. 3. Verify that the value 0x54h is read. 4. If the value 0x54h is not read, toggle the TVP5154 reset pin (RESETB, pin number 121). This procedure should be repeated if necessary until the value 0x54h is read from register 81h for all four decoders. Submit Documentation Feedback Power-Up, Reset, and Power-Down Sequence (Required) 19 TVP5154 4-CHANNEL LOW-POWER PAL/NTSC/SECAM VIDEO DECODER WITH INDEPENDENT SCALERS AND FAST LOCK www.ti.com SLES163A – MARCH 2006 – REVISED JULY 2006 Table 8-1. Reset and Power-Down Modes PDN RESETB CONFIGURATION 0 0 Reserved (undefined state) 0 1 Powers down the decoder 1 0 Resets the decoder 1 1 Normal operation 9 Internal Control Registers 9.1 Overview The TVP5154 decoder is initialized and controlled by sets of internal registers that set all device operating parameters. Communication between the external controller and the TVP5154 decoder is through the I2C. Two sets of registers exist, direct and indirect. Table 9-1 shows the summary of the direct registers. Reserved registers must not be written. Reserved bits in the defined registers must be written with 0s, unless otherwise noted. The detailed programming information of each register is described in the following sections. I2C register 0xFE controls which of the four decoders receives I2C commands. I2C register 0xFF controls which decoder core responds to I2C reads. Note, for a read operation, it is necessary to perform a write first, in order to set the desired sub-address for reading. After power up and the hardware reset, each decoder must be started by writing 0x00h to register 7Fh for all four decoders. Table 9-1. Direct Register Summary ADDRESS DEFAULT R/W (1) Video input source selection #1 00h 00h R/W Analog channel controls 01h 15h R/W Operation mode controls 02h 00h R/W Miscellaneous controls 03h 01h R/W Autoswitch mask 04h DCh R/W Clock control 05h 08h R/W Color killer threshold control 06h 10h R/W Luminance processing control #1 07h 60h R/W Luminance processing control #2 08h 00h R/W Brightness control 09h 80h R/W Color saturation control 0Ah 80h R/W Hue control 0Bh 00h R/W Contrast control 0Ch 80h R/W Outputs and data rates select 0Dh 47h R/W Luminance processing control #3 0Eh 00h R/W Configuration shared pins 0Fh 08h R/W Reserved 10h Active video cropping start MSB for unscaled data 11h 00h R/W Active video cropping start LSB for unscaled data 12h 00h R/W Active video cropping stop MSB for unscaled data 13h 00h R/W Active video cropping stop LSB for unscaled data 14h 00h R/W Genlock/RTC 15h 01h R/W Horizontal sync start 16h 80h R/W REGISTER FUNCTION (1) 20 R = Read only, W = Write only, R/W = Read and write Internal Control Registers Submit Documentation Feedback TVP5154 4-CHANNEL LOW-POWER PAL/NTSC/SECAM VIDEO DECODER WITH INDEPENDENT SCALERS AND FAST LOCK www.ti.com SLES163A – MARCH 2006 – REVISED JULY 2006 Table 9-1. Direct Register Summary (continued) ADDRESS DEFAULT R/W (1) Ancillary SAV/EAV control 17h 52h R/W Vertical blanking start 18h 00h R/W REGISTER FUNCTION Vertical blanking stop 19h 00h R/W Chrominance processing control #1 1Ah 0Ch R/W Chrominance processing control #2 1Bh 14h R/W Interrupt reset register B 1Ch 00h R/W Interrupt enable register B 1Dh 00h R/W Interrupt configuration register B 1Eh 00h R/W Output control 1Fh 00h R/W Reserved 20h I2C indirect registers 21h–24h 00h R/W AVID start/control for scaled data 25h–26h 00h R/W 28h 00h R/W 29h–2Ah 00h R/W Reserved Video standard AVID stop for scaled data 27h Reserved 2Bh Cb gain factor 2Ch R Cr gain factor 2Dh R Reserved 656 Revision Select Reserved 2Eh–2Fh 30 00h R/W 31h–7Fh MSB of device ID 80h 51h R LSB of device ID 81h 54h R ROM major version 82h 02h R ROM minor version 83h 00h R Vertical line count MSB 84h R Vertical line count LSB 85h R Interrupt status register B 86h R Interrupt active register B 87h R Status register #1 88h R Status register #2 89h R Status register #3 8Ah R Status register #4 8Bh R Status register #5 8Ch R Reserved 8Dh–8Fh Closed caption data registers 90h–93h R WSS data registers 94h–99h R VPS data registers 9Ah–A6h R VITC data registers A7h–AFh R VBI FIFO read data B0h R Teletext filter 1 B1h–B5h 00h R/W Teletext filter 2 B6h–BAh 00h R/W BBh 00h R/W Teletext filter enable Reserved BCh–BFh Interrupt status register A C0h 00h R/W Interrupt enable register A C1h 00h R/W Interrupt configuration C2h 04h R/W Submit Documentation Feedback Internal Control Registers 21 TVP5154 4-CHANNEL LOW-POWER PAL/NTSC/SECAM VIDEO DECODER WITH INDEPENDENT SCALERS AND FAST LOCK www.ti.com SLES163A – MARCH 2006 – REVISED JULY 2006 Table 9-1. Direct Register Summary (continued) ADDRESS DEFAULT R/W (1) VDP configuration RAM data C3h B8h R/W Configuration RAM address low byte C4h 1Fh R/W Configuration RAM address high byte C5h 00h R/W VDP status register C6h R FIFO word count C7h R FIFO interrupt threshold C8h 80h FIFO reset C9h 00h W Line number interrupt CAh 00h R/W Pixel alignment register low byte CBh 4Eh R/W Pixel alignment register high byte CCh 00h R/W FIFO output control CDh 01h R/W Reserved CEh Full field enable CFh 00h R/W D0h D1h–FBh 00h FFh R/W Full field mode register FCh 7Fh R/W Reserved FDh Decoder core write enables FEh 0Fh R/W Decoder core read enables FFh 00h R/W REGISTER FUNCTION Line mode registers R/W 9.2 Direct Register Definitions Direct registers are written to by performing a 3-byte I2C transaction: START : DEVICE_ID : SUB_ADDRESS : DATA : STOP Each direct register is eight bits wide. 9.2.1 Video Input Source Selection #1 Register Address 00h Default 00h 7 6 5 4 Reserved 3 2 1 0 Black output Reserved Channel n source selection S-video selection Channel n source selection: 0 = AIPnA selected (default) 1 = AIPnB selected 22 Internal Control Registers Submit Documentation Feedback TVP5154 4-CHANNEL LOW-POWER PAL/NTSC/SECAM VIDEO DECODER WITH INDEPENDENT SCALERS AND FAST LOCK www.ti.com SLES163A – MARCH 2006 – REVISED JULY 2006 Table 9-2. Analog Channel and Video Mode Selection ADDRESS 00 INPUT(S) SELECTED BIT 1 BIT 0 AIPnA (default) 0 0 AIPnB 1 0 AIPnA (luma), AIPnB (chroma) x 1 Composite S-Video Where n = 1, 2, 3, 4 Black output: 0 = Normal operation (default) 1 = Force black screen output (outputs synchronized) a. Forced to 10h in normal mode b. Forced to 01h in extended mode 9.2.2 Analog Channel Controls Register Address 01h Default 15h 7 6 5 Reserved 4 1 3 2 Automatic offset control 1 0 Automatic gain control Automatic offset control: 00 = Disabled 01 = Automatic offset enabled (default) 10 = Reserved 11 = Offset level frozen to the previously set value Automatic gain control (AGC): 00 = Disabled (fixed gain value) 01 = AGC enabled (default) 10 = Reserved 11 = AGC frozen to the previously set value Submit Documentation Feedback Internal Control Registers 23 TVP5154 4-CHANNEL LOW-POWER PAL/NTSC/SECAM VIDEO DECODER WITH INDEPENDENT SCALERS AND FAST LOCK www.ti.com SLES163A – MARCH 2006 – REVISED JULY 2006 9.2.3 Operation Mode Controls Register Address 02h Default 00h 7 6 Fast lock mode Color burst reference enable 5 4 TV/VCR mode 3 2 1 0 White peak disable Color subcarrier PLL frozen Luma peak disable Power down mode Fast lock mode: 0 = Normal operation (default) 1 = Fast lock mode. Locks within three fields if stable input signal and forced video standard. Color burst reference enable: 0 = Color burst reference for AGC disabled (default) 1 = Color burst reference for AGC enabled TV/VCR mode: 00 = Automatic mode determined by the internal detection circuit (default) 01 = Reserved 10 = VCR (nonstandard video) mode 11 = TV (standard video) mode With automatic detection enabled, unstable or nonstandard syncs on the input video forces the detector into the VCR mode. This turns off the comb filters and turns on the chroma trap filter. White peak disable: 0 = White peak protection enabled (default) 1 = White peak protection disabled Color subcarrier PLL frozen: 0 = Color subcarrier PLL increments by the internally generated phase increment (default). GLCO pin outputs the frequency increment. 1 = Color subcarrier PLL stops operating. GLCO pin outputs the frozen frequency increment. Luma peak disable 0 = Luma peak processing enabled (default) 1 = Luma peak processing disabled Power-down mode: 0 = Normal operation (default) 1 = Power-down mode. A/Ds are turned off and internal clocks are reduced to minimum. 24 Internal Control Registers Submit Documentation Feedback TVP5154 4-CHANNEL LOW-POWER PAL/NTSC/SECAM VIDEO DECODER WITH INDEPENDENT SCALERS AND FAST LOCK www.ti.com SLES163A – MARCH 2006 – REVISED JULY 2006 9.2.4 Miscellaneous Control Register Address 03h Default 01h 7 6 5 4 3 2 1 0 VBKO GPCL pin GPCL output enable Lock status (HVLK) YCbCr output enable(TVPOE) HSYNC, VSYNC/PALI, AVID, FID/GLCO output enable Vertical blanking on/off CLK output enable VBKO (pins 41, 60, 83, 102) function select: 0 = GPCL (default) 1 = VBLK Note, if these pins are not configured as outputs, they must not be left floating. A 10-kΩ pulldown resistor is recommended if not driven externally. GPCL (data is output based on state of bit 5): 0 = GPCL outputs 0 (default) 1 = GPCL outputs 1 GPCL output enable:(1) 0 = GPCL is inactive (default). 1 = GPCL is output. Note, if these pins are not configured as outputs, they must not be left floating. A 10-kΩ pulldown resistor is recommended if not driven externally. (1)GPCL should not be programmed to be 0 when register 0Fh bit 1 is ‘1 (programmed to be GPCL/VBLK). Lock status (HVLK) (configured along with register 0Fh, see Figure 9-1 for the relationship between the configuration shared pins): 0 = Terminal VSYNC/PALI outputs the PAL indicator (PALI) signal and terminal FID/GLCO outputs the field ID (FID) signal (default) (if terminals are configured to output PALI and FID in register 0Fh). 1 = Terminal VSYNC/PALI outputs the horizontal lock indicator (HLK) and terminal FID outputs the vertical lock indicator (VLK) (if terminals are configured to output PALI and FID in register 0Fh). These are additional functionalities that are provided for ease of use. YCbCr output enable: 0 = YOUT[7:0] high impedance (default) 1 = YOUT[7:0] active Note, if these pins are not configured as outputs, they must not be left floating. A 10-kΩ pulldown resistor is recommended if not driven externally. HSYNC, VSYNC/PALI, active video indicator (AVID), and FID/GLCO output enables: 0 = HSYNC, VSYNC/PALI, AVID, and FID/GLCO are high impedance (default). 1 = HSYNC, VSYNC/PALI, AVID, and FID/GLCO are active. Note, if these pins are not configured as outputs, they must not be left floating. A 10-kΩ pulldown resistor is recommended if not driven externally. Vertical blanking on/off: 0 = Vertical blanking (VBLK) off (default) 1 = Vertical blanking (VBLK) on CLK output enable: 0 = CLK output is high impedance. 1 = CLK output is enabled (default). Note: CLK edge and SCLK are configured through register 05h. Table 9-3. Digital Output Control (1) Submit Documentation Feedback REGISTER 03h, BIT 3 (TVPOE) (1) REGISTER C2h, BIT 2 (VDPOE) (1) YCbCr OUTPUT 0 X High impedance X 0 High impedance 1 1 Active VDPOE default is 1 and TVPOE default is 0. Internal Control Registers 25 TVP5154 4-CHANNEL LOW-POWER PAL/NTSC/SECAM VIDEO DECODER WITH INDEPENDENT SCALERS AND FAST LOCK www.ti.com SLES163A – MARCH 2006 – REVISED JULY 2006 0F(Bit 2) VSYNC/PALI 0F(Bit 4) LOCK24B VSYNC PALI HLK 0 HVLK 1 HVLK 1 VLK 0 0 0 M U X HLK/HVLK 1 M U X VLK/HVLK 1 FID 0 M U X PALI/HLK/HVLK 1 M U X FID/VLK/HVLK 0 GLCO 1 M U X VSYNC/PALI/HLK/HVLK M U X FID/GLCO/VLK/HVLK Pins 38, 57, 76, 95 Pins 37, 56, 75, 94 0F(Bit 6) LOCK23 0F(Bit 3) FID/GLCO 03(Bit 4) HVLK VBLK 1 GPCL 0 M U X VBLK/GPCL 1 INTREQ 03(Bit 7) VBKO 0 M U X INTREQ/GPCL//VBLK Pins 41, 60, 83, 102 CLK 0 PCLK 1 0F(Bit 1) INTREQ/GPCL/VBLK M U X PCLK/CLK Pins 42, 61, 84, 103 0F(Bit 0) CLK/PCLK NOTE: Also refer to the configuration shared pins register at subaddress 0Fh. Figure 9-1. Configuration Shared Pins 26 Internal Control Registers Submit Documentation Feedback TVP5154 4-CHANNEL LOW-POWER PAL/NTSC/SECAM VIDEO DECODER WITH INDEPENDENT SCALERS AND FAST LOCK www.ti.com SLES163A – MARCH 2006 – REVISED JULY 2006 9.2.5 Autoswitch Mask Register Address 04h Default DCh 7 6 Reserved N443_OFF: 0= 1= PALN_OFF: 0= 1= PALM_OFF: 0= 1= SEC_OFF: 0= 1= 9.2.6 5 4 3 2 SEC_OFF N443_OFF PALN_OFF PALM_OFF 1 0 Reserved NTSC443 is unmasked from the autoswitch process. Autoswitch does switch to NTSC443. NTSC443 is masked from the autoswitch process. Autoswitch does not switch to NTSC443 (default). PAL-N is unmasked from the autoswitch process. Autoswitch does switch to PAL-N. PAL-N is masked from the autoswitch process. Autoswitch does not switch to PAL-N (default). PAL-M is unmasked from the autoswitch process. Autoswitch does switch to PAL-M. PAL-M is masked from the autoswitch process. Autoswitch does not switch to PAL-M (default). SECAM is unmasked from the autoswitch process. Autoswitch does switch to SECAM (default). SECAM is masked from the autoswitch process. Autoswitch does not switch to SECAM. Clock Control Register Address 05h Default 08h 7 6 5 4 Reserved 3 2 1 0 SCLK OE Reserved SCLK edge CLK edge CLK edge 0 = CLK data changes on falling edge of CLK. 1 = CLK data changes on rising edge of CLK. SCLK edge 0 = SCLK data changes on falling edge of SCLK. 1 = SCLK data changes on rising edge of SCLK. SCLK OE 0 = SCLK output disabled. Output is high impedance. 1 = SCLK output enabled. NOTE: CLK OE is configured through register 0x03 to maintain compatibility with the TVP5150 family of devices. 9.2.7 Color Killer Threshold Control Register Address 06h Default 10h 7 Reserved 6 5 Automatic color killer 4 3 2 1 0 Color killer threshold Automatic color killer: 00 = Automatic mode (default) 01 = Reserved 10 = Color killer enabled, the CbCr terminals are forced to a zero color state. 11 = Color killer disabled Color killer threshold: 11111 = –30 dB (minimum) 10000 = – 24 dB (default) 00000 = – 18 dB (maximum) Submit Documentation Feedback Internal Control Registers 27 TVP5154 4-CHANNEL LOW-POWER PAL/NTSC/SECAM VIDEO DECODER WITH INDEPENDENT SCALERS AND FAST LOCK www.ti.com SLES163A – MARCH 2006 – REVISED JULY 2006 9.2.8 Luminance Processing Control #1 Register Address 07h Default 60h 7 6 5 4 3 2× luma output enable Pedestal not present Disable raw header Luma bypass enabled during vertical blanking 2 1 0 Luminance signal delay with respect to chrominance signal 2× luma output enable: 0 = Output depends on bit 4, luminance bypass enabled during vertical blanking (default). 1 = Outputs 2x luma samples during the entire frame. This bit takes precedence over bit 4. Pedestal not present: 0 = 7.5 IRE pedestal is present on the analog video input signal. 1 = Pedestal is not present on the analog video input signal (default). Disable raw header: 0 = Insert 656 ancillary headers for raw data 1 = Disable 656 ancillary headers and instead force dummy ones (0x40) (default) Luminance bypass enabled during vertical blanking: 0 = Disabled. If bit 7, 2× luma output enable, is 0, normal luminance processing occurs and YCbCr samples are output during the entire frame (default). 1 = Enabled. If bit 7, 2× luma output enable, is 0, normal luminance processing occurs and YCbCr samples are output during VACTIVE and 2× luma samples are output during VBLK. Luminance bypass occurs for the duration of the vertical blanking as defined by registers 18h and 19h. Luma signal delay with respect to chroma signal in pixel clock increments (range –8 to 7 pixel clocks): 1111 = – 8 pixel clocks delay 1011 = – 4 pixel clocks delay 1000 = – 1 pixel clocks delay 0000 = 0 pixel clocks delay (default) 0011 = 3 pixel clocks delay 0111 = 7 pixel clocks delay 9.2.9 Luminance Processing Control #2 Register Address 08h Default 00h 7 6 Reserved Luminance filter select 5 4 3 Reserved 2 1 Peaking gain 0 Reserved Luminance filter select: 0 = Luminance comb filter enabled (default) 1 = Luminance chroma trap filter enabled Peaking gain (sharpness): 00 = 0 (default) 01 = 0.5 10 = 1 11 = 2 Information on peaking frequency: ITU-R BT.601 sampling rate: all standards — peaking center frequency is 2.6 MHz 9.2.10 Brightness Control Register Address 09h Default 80h 7 6 5 4 3 2 1 0 Brightness control Brightness control: 1111 1111 = 255 (bright) 1000 0000 = 128 (default) 0000 0000 = 0 (dark) 28 Internal Control Registers Submit Documentation Feedback TVP5154 4-CHANNEL LOW-POWER PAL/NTSC/SECAM VIDEO DECODER WITH INDEPENDENT SCALERS AND FAST LOCK www.ti.com SLES163A – MARCH 2006 – REVISED JULY 2006 9.2.11 Color Saturation Control Register Address 0Ah Default 80h 7 6 5 4 3 2 1 0 3 2 1 0 3 2 1 0 Saturation control Saturation control: 1111 1111 = 255 (maximum) 1000 0000 = 128 (default) 0000 0000 = 0 (no color) 9.2.12 Hue Control Register (does not apply to SECAM) Address 0Bh Default 00h 7 6 5 4 Hue control Hue control: 0111 1111 = +180 degrees 0000 0000 = 0 degrees (default) 1000 0000 = – 180 degrees 9.2.13 Contrast Control Register Address 0Ch Default 80h 7 6 5 4 Contrast control Contrast control: 1111 1111 = 255 (maximum contrast) 1000 0000 = 128 (default) 0000 0000 = 0 (minimum contrast) Submit Documentation Feedback Internal Control Registers 29 TVP5154 4-CHANNEL LOW-POWER PAL/NTSC/SECAM VIDEO DECODER WITH INDEPENDENT SCALERS AND FAST LOCK www.ti.com SLES163A – MARCH 2006 – REVISED JULY 2006 9.2.14 Outputs and Data Rates Select Register Address 0Dh Default 47h 7 6 5 Reserved YCbCr output code range CbCr code format 4 3 YCbCr data path bypass 2 1 0 YCbCr output format YCbCr output code range: 0 = ITU-R BT.601 coding range (Y ranges from 16 to 235. U and V range from 16 to 240) 1 = Extended coding range (Y, U, and V range from 1 to 254) (default) CbCr code format: 0 = Offset binary code (2s complement + 128) (default) 1 = Straight binary code (2s complement) YCbCr data path bypass: 00 = Normal operation (default) 01 = Decimation filter output connects directly to the YCbCr output pins. This data is similar to the digitized composite data, but the HBLANK area is replaced with ITU-R BT.656 digital blanking. 10 = Digitized composite (or digitized S-video luma). A/D output connects directly to the YCbCr output pins. 11 = Reserved YCbCr output format: 000 = 8-bit 4:2:2 YCbCr with discrete sync output 001 = Reserved 010 = Reserved 011 = Reserved 100 = Reserved 101 = Reserved 110 = Reserved 111 = 8-bit ITU-R BT.656 interface with embedded sync output (default) 9.2.15 Luminance Processing Control #3 Register Address 0Eh Default 00h 7 6 5 4 Reserved 3 2 1 0 Luminance trap filter select Luminance filter stop band bandwidth (MHz): 00 = No notch (default) 01 = Notch 1 10 = Notch 2 11 = Notch Luminance filter select [1:0] selects one of the four chroma trap (notch) filters to produce luminance signal by removing the chrominance signal from the composite video signal. The stopband of the chroma trap filter is centered at the chroma subcarrier frequency, with stopband bandwidth controlled by the two control bits. Refer to Table 9-4 for the stopband bandwidths. The WCF bit is controlled in the chrominance control #2 register. 30 Internal Control Registers Submit Documentation Feedback TVP5154 4-CHANNEL LOW-POWER PAL/NTSC/SECAM VIDEO DECODER WITH INDEPENDENT SCALERS AND FAST LOCK www.ti.com SLES163A – MARCH 2006 – REVISED JULY 2006 Table 9-4. Luma Filter Selection WCF 0 1 9.2.16 FILTER SELECT NTSC/PAL/SECAM ITU-R BT.601 00 1.2214 01 0.8782 10 0.7297 11 0.4986 00 1.4170 01 1.0303 10 0.8438 11 0.5537 Configuration Shared Pins Register Address 0Fh Default 08h 7 6 5 4 3 2 1 0 Reserved FID PIN Reserved PALI PIN FID/GLCO VSYNC/PALI INTREQ/GPCL/VBLK CLK/PCLK FID PIN function select: 0 = FID (default, if bit 3 is selected to output FID) 1 = Lock indicator (indicates whether the device is locked vertically) PALI PIN function select: 0 = PALI (default, if bit 2 is selected to output PALI) 1 = Lock indicator (indicates whether the device is locked horizontally) FID/GLCO function select (also refer to register 03h for enhanced functionality): 0 = FID 1 = GLCO (default) VSYNC/PALI function select (also refer to register 03h for enhanced functionality): 0 = VSYNC (default) 1 = PALI INTREQ/GPCL/VBLK function select: 0 = INTREQ (default) 1 = GPCL or VBLK depending on bit 7 of register 03h CLK/PCLK (pins 42, 61, 84, 103) function select: 0 = CLK at 27 MHz (default) 1 = PCLK (1× pixel clock frequency at 13.5 MHz) See Figure 9-1 for the relationship between the configuration shared pins. 9.2.17 Active Video Cropping Start Pixel MSB for Unscaled Data Register Address 11h Default 00h 7 6 5 4 3 2 1 0 AVID start pixel MSB [9:2] Active video cropping start pixel MSB [9:2], set this register first before setting register 12h. The TVP5154 decoder updates the AVID start values only when register 12h is written to. This start pixel value is relative to the default values of the AVID start pixel. Submit Documentation Feedback Internal Control Registers 31 TVP5154 4-CHANNEL LOW-POWER PAL/NTSC/SECAM VIDEO DECODER WITH INDEPENDENT SCALERS AND FAST LOCK www.ti.com SLES163A – MARCH 2006 – REVISED JULY 2006 9.2.18 Active Video Cropping Start Pixel LSB for Unscaled Data Register Address 12h Default 00h 7 6 5 4 3 2 Reserved 1 AVID active 0 AVID start pixel LSB [1:0] AVID active: 0 = AVID out active in VBLK (default) 1 = AVID out inactive in VBLK AVID start [9:0] (combined registers 11h and 12h): 01 1111 1111 = 511 00 0000 0001 = 1 00 0000 0000 = 0 (default) 11 1111 1111 = – 1 10 0000 0000 = – 512 Active video cropping start pixel LSB [1:0]: The TVP5154 decoder updates the AVID start values only when this register is written to. 9.2.19 Active Video Cropping Stop Pixel MSB LSB for Unscaled Data Register Address 13h Default 00h 7 6 5 4 3 2 1 0 AVID stop pixel MSB [9:2] Active video cropping stop pixel MSB [9:2], set this register first before setting the register 14h. The TVP5154 decoder updates the AVID stop values only when register 14h is written to. This stop pixel value is relative to the default values of the AVID stop pixel. 9.2.20 Active Video Cropping Stop Pixel LSB for Unscaled Data Register Address 14h Default 00h 7 6 5 4 Reserved 3 2 1 0 AVID stop pixel LSB [1:0] Active video cropping stop pixel LSB [1:0]: The number of pixels of active video must be an even number. The TVP5154 decoder updates the AVID stop values only when this register is written to. AVID stop [9:0] (combined registers 13h and 14h): 01 1111 1111 = 511 00 0000 0001 = 1 00 0000 0000 = 0 (default) (see Figure 4-2) and Figure 4-3) 11 1111 1111 = – 1 10 0000 0000 = – 512 32 Internal Control Registers Submit Documentation Feedback TVP5154 4-CHANNEL LOW-POWER PAL/NTSC/SECAM VIDEO DECODER WITH INDEPENDENT SCALERS AND FAST LOCK www.ti.com SLES163A – MARCH 2006 – REVISED JULY 2006 9.2.21 Genlock and RTC Register Address 15h Default 01h 7 6 Stable syncs Reserved 5 4 3 F/V bit control 2 Auto inc 1 0 GLCO/RTC Stable syncs 0 = Output F and V bits follow the input signal producing fixed vertical blanking periods by adapting the active video. 1 = Output F and V bits produce fixed active video periods by adapting the vertical blanking. F/V bit control Table 9-5. F/V Bit Control BIT 5 0 BIT 4 NUMBER OF LINES 0 0 1 1 0 1 1 F BIT V BIT Standard ITU-R BT.656 ITU-R BT.656 Nonstandard even Force to 1 Switch at field boundary Nonstandard odd Toggles Switch at field boundary Standard ITU-R BT.656 ITU-R BT.656 Nonstandard Toggles Switch at field boundary Standard ITU-R BT.656 ITU-R BT.656 Nonstandard Pulse mode Switch at field boundary Illegal Auto inc: When this bit is set to 1, subsequent reading/writing from/to back door registers automatically increment the address index. GLCO/RTC: Table 9-6 for different modes. Table 9-6. GLCO/RTC Control BIT 2 BIT 1 BIT 0 0 x 0 GLCO GENLOCK/RTC MODE 0 x 1 RTC output mode 0 (default) 1 x 0 GLCO 1 x 1 RTC output mode 1 All other values are reserved. Figure 7-1 shows the timing of GLCO and the timing of RTC. Submit Documentation Feedback Internal Control Registers 33 TVP5154 4-CHANNEL LOW-POWER PAL/NTSC/SECAM VIDEO DECODER WITH INDEPENDENT SCALERS AND FAST LOCK www.ti.com SLES163A – MARCH 2006 – REVISED JULY 2006 9.2.22 Horizontal Sync (HSYNC) Start Register Address 16h Default 80h 7 6 5 4 3 2 1 0 HSYNC start HSYNC start: 1111 1111 = 1111 1110 = 1000 0001 = 1000 0000 = 0111 1111 = 0111 1110 = 0000 0000 = – 127 × 4 pixel clocks – 126 × 4 pixel clocks – 1 × 4 pixel clocks 0 pixel clocks (default) 1 × 4 pixel clocks 2 × 4 pixel clocks 128 × 4 pixel clocks BT.656 EAV Code YOUT[7:0] U Y V Y F F 0 0 0 0 X Y 8 0 BT.656 SAV Code 1 0 8 0 1 0 F F 0 0 0 0 X Y U Y HSYNC AVID 128 SCLK Start of Digital Active Line Nhbhs Nhb Figure 9-2. Horizontal Sync Table 9-7. Clock Delays (CLKs) STANDARD Nhbhs Nhb NTSC 16 272 PAL 20 284 SECAM 40 280 Detailed timing information is also available in Section 4.12, Synchronization Signals. 34 Internal Control Registers Submit Documentation Feedback TVP5154 4-CHANNEL LOW-POWER PAL/NTSC/SECAM VIDEO DECODER WITH INDEPENDENT SCALERS AND FAST LOCK www.ti.com SLES163A – MARCH 2006 – REVISED JULY 2006 9.2.23 Ancillary SAV/EAV Control Address 17h Default 52h 7 6 5 4 3 2 1 0 Reserved Scaler PD Include scale ancillary Include scale SAV Include scale EAV Include unscale ancillary Include unscale SAV Include unscale EAV Include unscaled EAV: 0 = AVID period does not include the EAV sync codes (default). 1 = AVID period includes the EAV sync codes. Include unscaled SAV: 0 = AVID period does not include the SAV sync codes. 1 = AVID period includes the SAV sync codes (default). Include unscaled ancillary data: 0 = AVID period includes the ancillary data region (default). 1 = AVID period does not include the ancillary data region. Include scaled EAV: 0 = AVID period does not include the EAV sync codes (default). 1 = AVID period includes the EAV sync codes. Include scaled SAV: 0 = AVID period does not include the SAV sync codes. 1 = AVID period includes the SAV sync codes (default). Include scaled ancillary data: 0 = AVID period includes the ancillary data region (default). 1 = AVID period does not include the ancillary data region. Scaler PD (scaler power down): 0 = Scaler active 1 = Scaler powered down (default) Data SAV EAV Pixel Data ANC Un−scaled pixel data AVID Include SAV = 0, Include EAV = 0, Include ancillary = 1 AVID Include SAV = 1, Include EAV = 0, Include ancillary = 0 AVID Data Include SAV = 0, Include EAV = 1, Include ancillary = 1 SAV Pixel Data EAV ANC Scaled pixel data, AVID start/stop reduced AVID Include SAV = 0, Include EAV = 0, Include ancillary = 1 AVID Include SAV = 1, Include EAV = 0, Include ancillary = 0 AVID Include SAV = 0, Include EAV = 1, Include ancillary = 1 Figure 9-3. AVID Behavior When Ancillary Data Present Submit Documentation Feedback Internal Control Registers 35 TVP5154 4-CHANNEL LOW-POWER PAL/NTSC/SECAM VIDEO DECODER WITH INDEPENDENT SCALERS AND FAST LOCK www.ti.com SLES163A – MARCH 2006 – REVISED JULY 2006 Data SAV Pixel Data EAV Un−scaled pixel data AVID Include SAV = 0, Include EAV = 0 AVID Include SAV = 1, Include EAV = 0 AVID Include SAV = 0, Include EAV = 1 Data SAV 0 Data Pixel Data EAV Scaled pixel data, AVID start/stop same as for un−scaled data AVID Include SAV = 0, Include EAV = 0 AVID Include SAV = 1, Include EAV = 0 AVID Include SAV = 0, Include EAV = 1 Data SAV Pixel Data EAV Scaled pixel data, AVID start/stop reduced AVID Include SAV = 0, Include EAV = 0 AVID Include SAV = 1, Include EAV = 0 AVID Include SAV = 0, Include EAV = 1 Figure 9-4. AVID Behavior When No Ancillary Data Present 36 Internal Control Registers Submit Documentation Feedback TVP5154 4-CHANNEL LOW-POWER PAL/NTSC/SECAM VIDEO DECODER WITH INDEPENDENT SCALERS AND FAST LOCK www.ti.com SLES163A – MARCH 2006 – REVISED JULY 2006 9.2.24 Vertical Blanking Start Register Address 18h Default 00h 7 6 5 4 3 2 1 0 Vertical blanking start Vertical blanking (VBLK) start: 0111 1111 = 127 lines after start of vertical blanking interval 0000 0001 = 1 line after start of vertical blanking interval 0000 0000 = Same time as start of vertical blanking interval (default) (see Figure 4-1, Figure 4-2, and Figure 4-3) 1111 1111 = 1 line before start of vertical blanking interval 1000 0000 = 128 lines before start of vertical blanking interval Vertical register register register 9.2.25 blanking is adjustable with respect to the standard vertical blanking intervals. The setting in this determines the timing of the GPCL/VBLK signal when it is configured to output vertical blank (see 03h). The setting in this register also determines the duration of the luma bypass function (see 07h). Vertical Blanking Stop Register Address 19h Default 00h 7 6 5 4 3 2 1 0 Vertical blanking stop Vertical blanking (VBLK) stop: 0111 1111 = 127 lines after stop of vertical blanking interval 0000 0001 = 1 line after stop of vertical blanking interval 0000 0000 = Same time as stop of vertical blanking interval (default) (see Figure 4-1, Figure 4-2, and Figure 4-3) 1111 1111 = 1 line before stop of vertical blanking interval 1000 0000 = 128 lines before stop of vertical blanking interval Vertical register register register 9.2.26 blanking is adjustable with respect to the standard vertical blanking intervals. The setting in this determines the timing of the GPCL/VBLK signal when it is configured to output vertical blank (see 03h). The setting in this register also determines the duration of the luma bypass function (see 07h). Chrominance Control #1 Register Address 1Ah Default 0Ch 7 6 5 Reserved color 4 3 2 1 PLL reset Chrominance adaptive comb filter enable (ACE) Chrominance comb filter enable (CE) 0 Automatic color gain control Color PLL reset: 0 = Color PLL not reset (default) 1 = Color PLL reset Writing a 1 to this bit resets the color PLL and transmits a 1 in the reset bit of the GLCO output stream. Chrominance adaptive comb filter enable (ACE): 0 = Disable 1 = Enable (default) Chrominance comb filter enable (CE): 0 = Disable 1 = Enable (default) Automatic color gain control (ACGC): 00 = ACGC enabled (default) 01 = Reserved 10 = ACGC disabled 11 = ACGC frozen to the previously set value Submit Documentation Feedback Internal Control Registers 37 TVP5154 4-CHANNEL LOW-POWER PAL/NTSC/SECAM VIDEO DECODER WITH INDEPENDENT SCALERS AND FAST LOCK www.ti.com SLES163A – MARCH 2006 – REVISED JULY 2006 9.2.27 Chrominance Control #2 Register Address 1Bh Default 14h 7 6 5 4 Reserved 3 2 Reserved WCF 1 0 Chrominance filter select Wideband chroma filter (WCF): 0 = Disable 1 = Enable (default) Chrominance filter select: 00 = No notch (default) 01 = Notch 1 10 = Notch 2 11 = Notch 3 Chrominance output bandwidth (MHz), see Table 9-8 Table 9-8. Chroma Output Bandwidth Select WCF 0 1 38 Internal Control Registers FILTER SELECT NTSC/PAL/SECAM ITU-R BT.601 00 1.2214 01 0.8782 10 0.7297 11 0.4986 00 1.4170 01 1.0303 10 0.8438 11 0.5537 Submit Documentation Feedback TVP5154 4-CHANNEL LOW-POWER PAL/NTSC/SECAM VIDEO DECODER WITH INDEPENDENT SCALERS AND FAST LOCK www.ti.com SLES163A – MARCH 2006 – REVISED JULY 2006 9.2.28 Interrupt Reset Register B Address 1Ch Default 00h 7 6 5 4 3 2 1 0 Software initialization reset Reserved Reserved Field rate changed reset Line alternation changed reset Color lock changed reset H/V lock changed reset TV/VCR changed reset Interrupt reset register B is used by the external processor to reset the interrupt status bits in interrupt status register B. Bits loaded with a 1 allow the corresponding interrupt status bit to reset to 0. Bits loaded with a 0 have no effect on the interrupt status bits. Software initialization reset: 0 = No effect (default) 1 = Reset software initialization bit Field rate changed reset: 0 = No effect (default) 1 = Reset field rate changed bit Line alternation changed reset: 0 = No effect (default) 1 = Reset line alternation changed bit Color lock changed reset: 0 = No effect (default) 1 = Reset color lock changed bit H/V lock changed reset: 0 = No effect (default) 1 = Reset H/V lock changed bit TV/VCR changed reset [TV/VCR mode is determined by counting the total number of lines/frame. The mode switches to VCR for nonstandard number of lines]: 0 = No effect (default) 1 = Reset TV/VCR changed bit 9.2.29 Interrupt Enable Register B Address 1Dh Default 00h 7 6 5 4 3 2 1 0 Software initialization occurred enable Reserved Reserved Field rate changed Line alternation changed Color lock changed H/V lock changed TV/VCR changed Submit Documentation Feedback Internal Control Registers 39 TVP5154 4-CHANNEL LOW-POWER PAL/NTSC/SECAM VIDEO DECODER WITH INDEPENDENT SCALERS AND FAST LOCK www.ti.com SLES163A – MARCH 2006 – REVISED JULY 2006 Software initialization occurred enable: 0 = Disabled (default) 1 = Enabled Field rate changed: 0 = Disabled (default) 1 = Enabled Line alternation changed: 0 = Disabled (default) 1 = Enabled Color lock changed: 0 = Disabled (default) 1 = Enabled H/V lock changed: 0 = Disabled (default) 1 = Enabled TV/VCR changed: 0 = Disabled (default) 1 = Enabled Interrupt enable register B is used by the external processor to mask unnecessary interrupt sources for interrupt B. Bits loaded with a 1 allow the corresponding interrupt condition to generate an interrupt on the external pin. Conversely, bits loaded with 0s mask the corresponding interrupt condition from generating an interrupt on the external pin. This register only affects the external pin; it does not affect the bits in the interrupt status register. A given condition can set the appropriate bit in the status register and not cause an interrupt on the external pin. To determine if this device is driving the interrupt pin, either AND interrupt status register B with interrupt enable register B, or check the state of interrupt B in the interrupt B active register. 9.2.30 Interrupt Configuration Register B Address 1Eh Default 00h 7 6 5 4 Reserved 3 2 1 0 Interrupt polarity B Interrupt polarity B: 0 = Interrupt B is active low (default). 1 = Interrupt B is active high. Interrupt polarity B must be same as interrupt polarity A bit at bit 0 of the interrupt configuration register A at address C2h. Interrupt configuration register B is used to configure the polarity of interrupt B on the external interrupt pin. When the interrupt B is configured for active low, the pin is driven low when active and high impedance when inactive (open drain). Conversely, when the interrupt B is configured for active high, it is driven high for active and driven low for inactive. 40 Internal Control Registers Submit Documentation Feedback TVP5154 4-CHANNEL LOW-POWER PAL/NTSC/SECAM VIDEO DECODER WITH INDEPENDENT SCALERS AND FAST LOCK www.ti.com SLES163A – MARCH 2006 – REVISED JULY 2006 9.2.31 Output Control Address 1Fh Default 00h 7 6 5 4 3 2 Bit swap Ancillary Enable Parity modifier SAV/EAV modifier 1 0 Output mode Output mode: 000 = Mode 0 : Unscaled data clocked by clock 1 001 = Mode 1 : Scaled data clocked by clock 1 010 = Mode 2 : Multiplexed data with separate clocks 011 = Mode 3 : Multiplexed data with clock 1 at 54 MHz 100 = Mode 4 : Unscaled/scaled field toggled data clocked by clock 1 SAV/EAV modifier: 0 = SAV/EAV codes not modified 1 = SAV/EAV MSB modified. MSB = 1 indicates unscaled data, MSB = 0 indicates scaled data Parity modifier: 0 = Parity calculation includes SAV/EAV MSB. 1 = Parity calculation does not include SAV/EAV MSB. Ancillary enable: 0 = Ancillary data not enabled 1 = Ancillary data packet added to indicate scaled or unscaled data Note : Scaled/unscaled ancillary data cannot be enabled at the same time as VBI ancillary data Bit swap: 0 = chx_out(0) corresponds to data LSB, chx_out(7) corresponds to data MSB 1 = chx_out(0) corresponds to data MSB, chx_out(7) corresponds to data LSB Table 9-9. Ancillary Data Format and Sequence BYTE NO. D7 (MSB) D6 D5 D4 D3 D2 D1 D0 (LSB) 0 0 0 0 0 0 0 0 0 1 1 1 1 1 1 1 1 1 DESCRIPTION Ancillary data preamble 2 1 1 1 1 1 1 1 1 3 NEP EP 0 1 DID3 DID2 DID1 DID0 4 1 0 0 0 0 0 0 0 Secondary data ID (SDID) 5 0 1 0 0 0 0 0 1 Number of 32 bit data (NN) 6 Z Video line # [7:0] 0 0 0 0 8 Internal data ID0 (IDID0) 0 0 Video line # [9:8] 00h 9 1 0 11 1 0 Submit Documentation Feedback 0 Data Data byte 00h 0 Internal data ID1 (IDID1) Data byte 00h 10 Data ID (DID) 0 Check sum 0 0 0 Fill byte Internal Control Registers 41 TVP5154 4-CHANNEL LOW-POWER PAL/NTSC/SECAM VIDEO DECODER WITH INDEPENDENT SCALERS AND FAST LOCK www.ti.com SLES163A – MARCH 2006 – REVISED JULY 2006 EP: Even parity for D0–D5 NEP: Negated even parity DID: For unscaled data D0–D3 taken from EAV DID value for unscaled data stream register low nibble for field 0 and from high nibble for field 1 For scaled data D0–D3 taken from EAV DID value for scaled data stream register low nibble for field 0 and from high nibble for field 1 SDID: Zero data NN: Indicates 1 D word of data IDID0: Transaction video line number [7:0] IDID1: Bit 0/1 = Transaction video line number [9:8] CS: Sum of D0–D7 of DID through last data byte Fill byte: Fill bytes make a multiple of four bytes from byte 0 to last fill byte. For teletext modes, byte 8 is the sync pattern byte. Byte 9 is 1. Data (the first data byte). 9.2.32 Active Video Cropping Start Pixel MSB for Scaled Data Register Address 25h Default 00h 7 6 5 4 3 2 1 0 AVID start pixel MSB [9:2] Active video cropping start pixel MSB [9:2], set this register first before setting register 26h. The TVP5154 decoder updates the AVID start values only when register 26h is written to. This start pixel value is relative to the default values of the AVID start pixel. 9.2.33 Active Video Cropping Start Pixel LSB for Scaled Data Register Address 26h Default 00h 7 6 5 Reserved 4 3 2 Active 1 0 AVID start pixel LSB [1:0] AVID active: 0 = AVID out active in VBLK (default) 1 = AVID out inactive in VBLK Active video cropping start pixel LSB [1:0]: The TVP5154 decoder updates the AVID start values only when this register is written to. AVID start [9:0]: 01 1111 1111 = 511 00 0000 0001 = 1 00 0000 0000 = 0 (default) 11 1111 1111 = – 1 10 0000 0000 = – 512 42 Internal Control Registers Submit Documentation Feedback TVP5154 4-CHANNEL LOW-POWER PAL/NTSC/SECAM VIDEO DECODER WITH INDEPENDENT SCALERS AND FAST LOCK www.ti.com SLES163A – MARCH 2006 – REVISED JULY 2006 9.2.34 Video Standard Register Address 28h Default 00h 7 6 5 4 3 2 Reserved Video standard: 0000 = 0001 = 0010 = 0011 = 0100 = 0101 = 0110 = 0111 = 1000 = 1001 = 1010 = 1011 = 1100 = 1 0 Video standard Autoswitch mode (default) Reserved (M) NTSC ITU-R BT.601 Reserved (B, G, H, I, N) PAL ITU-R BT.601 Reserved (M) PAL ITU-R BT.601 Reserved (Combination-N) PAL ITU-R BT.601 Reserved NTSC 4.43 ITU-R BT.601 Reserved SECAM ITU-R BT.601 With the autoswitch code running, the user can force the device to operate in a particular video standard mode and sample rate by writing the appropriate value into this register. 9.2.35 Active Video Cropping Stop Pixel MSB for Scaled Data Register Address 29h Default 00h 7 6 5 4 3 2 1 0 AVID stop pixel MSB [9:2] Active video cropping stop pixel MSB [9:2], set this register first before setting the register 2Ah. The TVP5154 decoder updates the AVID stop values only when register 2Ah is written to. This stop pixel value is relative to the default values of the AVID stop pixel. 9.2.36 Active Video Cropping Stop Pixel LSB for Scaled Data Register Address 2Ah Default 00h 7 6 5 4 3 Reserved AVID stop [9:0]: 01 1111 1111 00 0000 0001 00 0000 0000 11 1111 1111 10 0000 0000 = = = = = 2 1 0 AVID stop pixel LSB [1:0] 511 1 0 (default) (see Figure 4-1, Figure 4-2, and Figure 4-3) –1 – 512 Active video cropping stop pixel LSB [1:0]: The number of pixels of active video must be an even number. The TVP5154 decoder updates the AVID stop values only when this register is written to. Submit Documentation Feedback Internal Control Registers 43 TVP5154 4-CHANNEL LOW-POWER PAL/NTSC/SECAM VIDEO DECODER WITH INDEPENDENT SCALERS AND FAST LOCK www.ti.com SLES163A – MARCH 2006 – REVISED JULY 2006 9.2.37 Address Cb Gain Factor Register 2Ch 7 6 5 4 3 2 1 0 Cb gain factor This is a read-only register that provides the gain applied to the Cb in the YCbCr data stream. 9.2.38 Address Cr Gain Factor Register 2Dh 7 6 5 4 3 2 1 0 Cr gain factor This is a read-only register that provides the gain applied to the Cr in the YCbCr data stream. 9.2.39 656 Revision Select Register Address 30h Default 00h 7 6 5 4 3 2 1 0 656 Rev 656 revision select: 0 = Adheres to ITU-R BT656.4 timing 1 = Adheres to ITU-R BT656.3 timing 9.2.40 MSB of Device ID Register Address 80h Default 51h 7 6 5 4 3 2 1 0 2 1 0 2 1 0 MSB of device ID This register identifies the MSB of the device ID. Value = 0x51. 9.2.41 LSB of Device ID Register Address 81h Default 54h 7 6 5 4 3 LSB of device ID This register identifies the LSB of the device ID. Value = 0x54. 9.2.42 ROM Major Version Register Address 82h Default 02h 7 6 5 4 3 ROM major version (1) (1) 44 This register can contain a number from 0x01 to 0xFF. Internal Control Registers Submit Documentation Feedback TVP5154 4-CHANNEL LOW-POWER PAL/NTSC/SECAM VIDEO DECODER WITH INDEPENDENT SCALERS AND FAST LOCK www.ti.com SLES163A – MARCH 2006 – REVISED JULY 2006 9.2.43 ROM Minor Version Register Address 83h Default 00h 7 6 5 4 3 ROM minor (1) 2 1 0 2 1 0 version (1) This register can contain a number from 0x01 to 0xFF. 9.2.44 Vertical Line Count MSB Register Address 84h 7 6 5 4 3 Reserved Vertical line count MSB Vertical line count bits [9:8] 9.2.45 Vertical Line Count LSB Register Address 85h 7 6 5 4 3 2 1 0 Vertical line count LSB Vertical line count bits [7:0] Registers 84h and 85h can be read and combined to extract the detected number of lines per frame. This can be used with nonstandard video signals, such as a VCR in fast-forward or rewind modes, to synchronize the downstream video circuitry. 9.2.46 Interrupt Status Register B Address 86h 7 6 5 4 3 2 1 0 Software initialization Reserved Command ready Field rate changed Line alternation changed Color lock changed H/V lock changed TV/VCR changed Software initialization: 0 = Software initialization is not ready (default). 1 = Software initialization is ready. Command ready: 0 = TVP5154 is not ready to accept a new command (default). 1 = TVP5154 is ready to accept a new command. Field rate changed: 0 = Field rate has not changed (default). 1 = Field rate has changed. Line alternation changed: 0 = Line alteration has not changed (default). 1 = Line alternation has changed. Color lock changed: 0 = Color lock status has not changed (default). 1 = Color lock status has changed. H/V lock changed: 0 = H/V lock status has not changed (default). 1 = H/V lock status has changed. TV/VCR changed: 0 = TV/VCR status has not changed (default). 1 = TV/VCR status has changed. Interrupt status register B is polled by the external processor to determine the interrupt source for interrupt B. After an interrupt condition is set, it can be reset by writing to the interrupt reset register B at subaddress 1Ch with a 1 in the appropriate bit. Submit Documentation Feedback Internal Control Registers 45 TVP5154 4-CHANNEL LOW-POWER PAL/NTSC/SECAM VIDEO DECODER WITH INDEPENDENT SCALERS AND FAST LOCK www.ti.com SLES163A – MARCH 2006 – REVISED JULY 2006 9.2.47 Interrupt Active Register B Address 87h 7 6 5 4 3 2 1 0 Reserved Interrupt B Interrupt B: 0 = Interrupt B is not active on the external terminal (default). 1 = Interrupt B is active on the external terminal. The interrupt active register B is polled by the external processor to determine if interrupt B is active. 9.2.48 Status Register #1 Address 88h 7 6 5 4 3 2 1 0 Peak white detect status Line-alternating status Field rate status Lost lock detect Color subcarrier lock status Vertical sync lock status Horizontal sync lock status TV/VCR status Peak white detect status: 0 = Peak white is not detected. 1 = Peak white is detected. Line–alternating status: 0 = Nonline alternating 1 = Line alternating Field rate status: 0 = 60 Hz 1 = 50 Hz Lost lock detect: 0 = No lost lock since status register #1 was last read 1 = Lost lock since status register #1 was last read Color subcarrier lock status: 0 = Color subcarrier is not locked. 1 = Color subcarrier is locked. Vertical sync lock status: 0 = Vertical sync is not locked. 1 = Vertical sync is locked. Horizontal sync lock status: 0 = Horizontal sync is not locked. 1 = Horizontal sync is locked. TV/VCR status. TV mode is determined by detecting standard line-to-line variations and specific chroma SCH phases based on the standard input video format. VCR mode is determined by detecting variations in the chroma SCH phases compared to the chroma SCH phases of the standard input video format. 0 = TV 1 = VCR 9.2.49 Address Status Register #2 89h 7 6 5 4 3 2 Reserved Weak signal detection PAL switch polarity Field sequence status AGC and offset frozen status 1 0 Reserved Weak signal detection: 0 = No weak signal 1 = Weak signal mode PAL switch polarity of first line of odd field: 0 = PAL switch is 0. 1 = PAL switch is 1. Field sequence status: 0 = Even field 1 = Odd field AGC and offset frozen status: 0 = AGC and offset are not frozen. 1 = AGC and offset are frozen. 46 Internal Control Registers Submit Documentation Feedback TVP5154 4-CHANNEL LOW-POWER PAL/NTSC/SECAM VIDEO DECODER WITH INDEPENDENT SCALERS AND FAST LOCK www.ti.com SLES163A – MARCH 2006 – REVISED JULY 2006 9.2.50 Status Register #3 Address 8Ah 7 6 5 4 3 Front-end AGC gain value (analog and (1) 2 1 0 2 1 0 digital) (1) Represents eight bits (MSB) of a 10-bit value This register provides the front-end AGC gain value of both analog and digital gains. 9.2.51 Status Register #4 Address 8Bh 7 6 5 4 3 Subcarrier to horizontal (SCH) phase SCH (color PLL subcarrier phase at 50% of the falling edge of horizontal sync of line one of odd field; step size 360°/256): 0000 0000 = 0.00o 0000 0001 = 1.41o 0000 0010 = 2.81o 1111 1110 = 357.2o 1111 1111 = 358.6o 9.2.52 Status Register #5 Address 8Ch 7 6 5 Autoswitch mode 4 3 Reserved 2 1 Video standard 0 Sampling rate Autoswitch mode: 0 = Stand-alone (forced video standard) mode 1 = Autoswitch mode This register contains information about the detected video standard and the sampling rate at which the device is currently operating. When autoswitch code is running, this register must be tested to determine which video standard has been detected. Table 9-10. Auto Switch Video Standard SR (1) VIDEO STANDARD [3:1] (1) VIDEO STANDARD BIT 3 BIT 2 BIT 1 BIT 0 0 0 0 0 Reserved 0 0 0 1 (M) NTSC ITU-R BT.601 0 0 1 0 Reserved 0 0 1 1 (B, G, H, I, N) PAL ITU-R BT.601 0 1 0 0 Reserved 0 1 0 1 (M) PAL ITU-R BT.601 0 1 1 0 Reserved 0 1 1 1 PAL-N ITU-R BT.601 1 0 0 0 Reserved 1 0 0 1 NTSC 4.43 ITU-R BT.601 1 0 1 0 Reserved 1 0 1 1 SECAM ITU-R BT.601 Sampling rate (SR): 0 = Reserved, 1 = ITU-R BT.601 Submit Documentation Feedback Internal Control Registers 47 TVP5154 4-CHANNEL LOW-POWER PAL/NTSC/SECAM VIDEO DECODER WITH INDEPENDENT SCALERS AND FAST LOCK www.ti.com SLES163A – MARCH 2006 – REVISED JULY 2006 9.2.53 Closed Caption Data Registers Address 90h–93h Address 7 6 5 4 3 2 90h Closed caption field 1 byte 1 91h Closed caption field 1 byte 2 92h Closed caption field 2 byte 1 93h Closed caption field 2 byte 2 1 0 These registers contain the closed caption data arranged in bytes per field. 9.2.54 WSS Data Registers Address 94h–99h NTSC abc Address 7 6 94h 95h b13 4 3 2 1 0 b4 b3 b2 b1 b0 WSS field 1 byte 1 BYTE b11 b10 b9 b8 b7 b6 WSS field 1 byte 2 96h b19 b18 b17 b16 b15 b14 WSS field 1 byte 3 97h b5 b4 b3 b2 b1 b0 WSS field 2 byte 1 b11 b10 b9 b8 b7 b6 WSS field 2 byte 2 b19 b18 b17 b16 b15 b14 WSS field 2 byte 3 98h b13 b12 5 b5 b12 99h These registers contain the wide screen signaling (WSS) data for NTSC. Bits 0–1 represent word 0, aspect ratio. Bits 2–5 represent word 1, header code for word 2. Bits 6–13 represent word 2, copy control. Bits 14–19 represent word 3, CRC. PAL/SECAM abc Address 7 6 94h b7 b6 95h 5 3 2 1 0 BYTE b5 b4 b3 b2 b1 b0 WSS field 1 byte 1 b13 b12 b11 b10 b9 b8 WSS field 1 byte 2 96h 97h 4 Reserved b7 b6 98h 99h b5 b4 b3 b2 b1 b0 WSS field 2 byte 1 b13 b12 b11 b10 b9 b8 WSS field 2 byte 2 Reserved Bits 0–3 represent group 1, aspect ratio. Bits 4–7 represent group 2, enhanced services. Bits 8–10 represent group 3, subtitles. Bits 11–13 represent group 4, others. 48 Internal Control Registers Submit Documentation Feedback TVP5154 4-CHANNEL LOW-POWER PAL/NTSC/SECAM VIDEO DECODER WITH INDEPENDENT SCALERS AND FAST LOCK www.ti.com SLES163A – MARCH 2006 – REVISED JULY 2006 9.2.55 VPS Data Registers Address 9Ah–A6h Address 7 6 5 4 3 9Ah VPS byte 1 9Bh VPS byte 2 9Ch VPS byte 3 9Dh VPS byte 4 9Eh VPS byte 5 9Fh VPS byte 6 A0h VPS byte 7 A1h VPS byte 8 A2h VPS byte 9 A3h VPS byte 10 A4h VPS byte 11 A5h VPS byte 12 A6h VPS byte 13 2 1 0 These registers contain the entire VPS data line except the clock run-in code or the start code. 9.2.56 VITC Data Registers Address A7h–AFh Address 7 6 5 4 A7h 3 2 1 0 VITC byte 1, frame byte 1 A8h VITC byte 2, frame byte 2 A9h VITC byte 3, seconds byte 1 AAh VITC byte 4, seconds byte 2 ABh VITC byte 5, minutes byte 1 ACh VITC byte 6, minutes byte 2 ADh VITC byte 7, hour byte 1 AEh VITC byte 8, hour byte 2 AFh VITC byte 9, CRC These registers contain the VITC data. 9.2.57 Address 7 VBI FIFO Read Data Register B0h 6 5 4 3 2 1 0 FIFO read data This address is provided to access VBI data in the FIFO through the host port. All forms of teletext data come directly from the FIFO, while all other forms of VBI data can be programmed to come from the registers or from the FIFO. Current status of the FIFO can be found at address C6h and the number of bytes in the FIFO is located at address C7h. If the host port is to be used to read data from the FIFO, the output formatter must be disabled at address CDh bit 0. The format used for the VBI FIFO is shown in Section 4.9. Submit Documentation Feedback Internal Control Registers 49 TVP5154 4-CHANNEL LOW-POWER PAL/NTSC/SECAM VIDEO DECODER WITH INDEPENDENT SCALERS AND FAST LOCK www.ti.com SLES163A – MARCH 2006 – REVISED JULY 2006 9.2.58 Teletext Filter and Mask Registers Address B1h–BAh Default 00h Address 7 6 5 4 3 2 1 B1h Filter 1 mask 1 Filter 1 pattern 1 B2h Filter 1 mask 2 Filter 1 pattern 2 B3h Filter 1 mask 3 Filter 1 pattern 3 B4h Filter 1 mask 4 Filter 1 pattern 4 B5h Filter 1 mask 5 Filter 1 pattern 5 B6h Filter 2 mask 1 Filter 2 pattern 1 B7h Filter 2 mask 2 Filter 2 pattern 2 B8h Filter 2 mask 3 Filter 2 pattern 3 B9h Filter 2 mask 4 Filter 2 pattern 4 BAh Filter 2 mask 5 Filter 2 pattern 5 0 For an NABTS system, the packet prefix consists of five bytes. Each byte contains four data bits (D[3:0]) interlaced with four Hamming protection bits (H[3:0]): Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0 D[3] H[3] D[2] H[2] D[1] H[1] D[0] H[0] Only the data portion D[3:0] from each byte is applied to a teletext filter function with the corresponding pattern bits P[3:0] and mask bits M[3:0]. Hamming protection bits are ignored by the filter. For a WST system (PAL or NTSC), the packet prefix consists of two bytes so that two patterns are used. Patterns 3, 4, and 5 are ignored. The mask bits enable filtering using the corresponding bit in the pattern register. For example, a 1 in the LSB of mask 1 means that the filter module must compare the LSB of nibble 1 in the pattern register to the first data bit on the transaction. If these match, a true result is returned. A 0 in a bit of mask 1 means that the filter module must ignore that data bit of the transaction. If all 0s are programmed in the mask bits, the filter matches all patterns returning a true result (default 00h). Pattern and mask for each byte and filter are referred as <1,2><P,M><1,2,3,4,5> where: <1,2> identifies the filter 1 or 2 <P,M> identifies the pattern or mask <1,2,3,4,5> identifies the byte number 50 Internal Control Registers Submit Documentation Feedback TVP5154 4-CHANNEL LOW-POWER PAL/NTSC/SECAM VIDEO DECODER WITH INDEPENDENT SCALERS AND FAST LOCK www.ti.com SLES163A – MARCH 2006 – REVISED JULY 2006 9.2.59 Teletext Filter Control Register Address BBh Default 00h 7 6 5 4 Reserved 3 Filter logic 2 1 0 Mode TTX filter 2 enable TTX filter 1 enable Filter logic: Allows different logic to be applied when combining the decision of filter 1 and filter 2 as follows: 00 = NOR (default) 01 = NAND 10 = OR 11 = AND Mode: 0 = Teletext WST PAL mode B (2 header bytes) (default) 1 = Teletext NABTS NTSC mode C (5 header bytes) TTX filter 2 enable: 0 = Disabled (default) 1 = Enabled TTX filter 1 enable: 0 = Disabled (default) 1 = Enabled If the filter matches or if the filter mask is all 0s, a true result is returned. 9.2.60 Interrupt Status Register A Address C0h Default 00h 7 6 Lock state interrupt Lock interrupt 5 4 Reserved 3 2 1 0 FIFO threshold interrupt Line interrupt Data interrupt Lock state interrupt: 0 = TVP5154 is not locked to the video signal (default) 1 = TVP5154 is locked to the video signal. Lock interrupt: 0 = A transition has not occurred on the lock signal (default). 1 = A transition has occurred on the lock signal. FIFO threshold interrupt: 0 = The amount of data in the FIFO has not yet crossed the threshold programmed at address C8h (default). 1 = The amount of data in the FIFO has crossed the threshold programmed at address C8h. Line interrupt: 0 = The video line number has not yet been reached (default). 1 = The video line number programmed in address CAh has occurred. Data interrupt: 0 = No data is available (default). 1 = VBI data is available either in the FIFO or in the VBI data registers. The interrupt status register A can be polled by the host processor to determine the source of an interrupt. After an interrupt condition is set it can be reset by writing to this register with a 1 in the appropriate bit(s). Submit Documentation Feedback Internal Control Registers 51 TVP5154 4-CHANNEL LOW-POWER PAL/NTSC/SECAM VIDEO DECODER WITH INDEPENDENT SCALERS AND FAST LOCK www.ti.com SLES163A – MARCH 2006 – REVISED JULY 2006 9.2.61 Interrupt Enable Register A Address C1h Default 00h 7 6 5 4 3 2 1 0 Reserved Lock interrupt enable Cycle complete interrupt enable Bus error interrupt enable Reserved FIFO threshold interrupt enable Line interrupt enable Data interrupt enable Lock interrupt enable: 0 = Disabled (default) 1 = Enabled Cycle complete interrupt enable: 0 = Disabled (default) 1 = Enabled Bus error interrupt enable: 0 = Disabled (default) 1 = Enabled FIFO threshold interrupt enable: 0 = Disabled (default) 1 = Enabled Line interrupt enable: 0 = Disabled (default) 1 = Enabled Data interrupt enable: 0 = Disabled (default) 1 = Enabled The interrupt enable register A is used by the host processor to mask unnecessary interrupt sources. Bits loaded with a 1 allow the corresponding interrupt condition to generate an interrupt on the external pin. Conversely, bits loaded with a 0 mask the corresponding interrupt condition from generating an interrupt on the external pin. This register only affects the interrupt on the external terminal, it does not affect the bits in interrupt status register A. A given condition can set the appropriate bit in the status register and not cause an interrupt on the external terminal. To determine if this device is driving the interrupt terminal either perform a logical AND of interrupt status register A with interrupt enable register A, or check the state of the interrupt A bit in the interrupt configuration register at address C2h. 52 Internal Control Registers Submit Documentation Feedback TVP5154 4-CHANNEL LOW-POWER PAL/NTSC/SECAM VIDEO DECODER WITH INDEPENDENT SCALERS AND FAST LOCK www.ti.com SLES163A – MARCH 2006 – REVISED JULY 2006 9.2.62 Interrupt Configuration Register A Address C2h Default 04h 7 6 5 4 3 Reserved 2 1 0 YCbCr enable (VDPOE) Interrupt A Interrupt polarity A YCbCr enable (VDPOE): 0 = YCbCr pins are high impedance. 1 = YCbCr pins are active if other conditions are met (default). Interrupt A (read only): 0 = Interrupt A is not active on the external pin (default). 1 = Interrupt A is active on the external pin. Interrupt polarity A: 0 = Interrupt A is active low (default). 1 = Interrupt A is active high. Interrupt configuration register A is used to configure the polarity of the external interrupt terminal. When interrupt A is configured as active low, the terminal is driven low when active and high impedance when inactive (open collector). Conversely, when the terminal is configured as active high, it is driven high when active and driven low when inactive. 9.2.63 VDP Configuration RAM Register Address C3h C4h C5h Default B8h 1Fh 00h Address 7 C3h C4h C5h 6 5 4 3 2 1 0 Configuration data RAM address (7:0) Reserved RAM address 8 The configuration RAM data is provided to initialize the VDP with initial constants. The configuration RAM is 512 bytes organized as 32 different configurations of 16 bytes each. The first 12 configurations are defined for the current VBI standards. An additional two configurations can be used as a custom programmed mode for unique standards, such as Gemstar. Address C3h is used to read or write to the RAM. The RAM internal address counter is automatically incremented with each transaction. Addresses C5h and C4h make up a 9-bit address to load the internal address counter with a specific start address. This can be used to write a subset of the RAM for only those standards of interest. Registers D0h–FBh must all be programmed with FFh before writing or reading the configuration RAM. Full field mode (CFh) must be disabled as well. The suggested RAM contents are shown in the following table. All values are hexadecimal. Submit Documentation Feedback Internal Control Registers 53 TVP5154 4-CHANNEL LOW-POWER PAL/NTSC/SECAM VIDEO DECODER WITH INDEPENDENT SCALERS AND FAST LOCK www.ti.com SLES163A – MARCH 2006 – REVISED JULY 2006 Index Address Reserved 000 WST SECAM 010 Reserved 020 WST PAL B 030 Reserved 040 WST PAL C 050 Reserved 060 WST NTSC 070 Reserved 080 NABTS, NTSC 090 Reserved 0A0 0 1 2 3 4 5 6 7 8 AA AA FF FF E7 2E 20 26 E6 AA AA FF FF 27 2E 20 2B AA AA FF FF E7 2E 20 22 A6 B C D E F B4 0E 0 0 0 10 0 72 10 0 0 0 10 0 98 0D 0 0 0 10 0 93 0D 0 0 0 10 0 93 0D 0 0 0 15 0 93 0D 0 0 0 10 0 7B 09 0 0 0 27 0 8C 09 0 0 0 27 0 CD 0F 0 0 0 3A 0 7C 08 0 0 0 39 0 85 08 0 0 0 4C 0 94 08 0 0 0 4C 0 DA 0B 0 0 0 60 0 Reserved A6 Reserved AA AA FF FF 27 2E 20 23 69 Reserved AA AA FF FF E7 2E 20 22 69 Reserved 0B0 Reserved 0C0 CC, PAL/SECAM 0D0 Reserved 0E0 CC, NTSC 0F0 Reserved 100 WSS, PAL/SECAM 110 Reserved 120 WSS, NTSC C 130 Reserved 140 VITC, PAL/SECAM 150 Reserved 160 VITC, NTSC 170 Reserved 180 VPS, PAL 190 Reserved 1A0 Reserved Custom 1 1B0 Programmable Reserved 1C0 Reserved Custom 2 1D0 Programmable Internal Control Registers A Reserved NABTS, NTSC–J 54 9 Reserved AA AA FF FF A7 2E 20 23 69 Reserved AA 2A FF 3F 04 51 6E 02 A6 Reserved AA 2A FF 3F 04 51 6E 02 69 Reserved 5B 55 C5 FF 0 71 6E 42 A6 Reserved 38 00 3F 00 0 71 6E 43 69 Reserved 0 0 0 0 0 8F 6D 49 A6 Reserved 0 0 0 0 0 8F 6D 49 AA AA FF FF BA CE 2B 0D 69 Reserved A6 Submit Documentation Feedback TVP5154 4-CHANNEL LOW-POWER PAL/NTSC/SECAM VIDEO DECODER WITH INDEPENDENT SCALERS AND FAST LOCK www.ti.com SLES163A – MARCH 2006 – REVISED JULY 2006 9.2.64 Address VDP Status Register C6h 7 6 5 4 3 2 1 0 FIFO full error FIFO empty TTX available CC field 1 available CC field 2 available WSS available VPS available VITC available The VDP status register indicates whether data is available in either the FIFO or data registers, and status information about the FIFO. Reading data from the corresponding register does not clear the status flags automatically. These flags are only reset by writing a 1 to the respective bit. However, bit 6 is updated automatically. FIFO full error: 0 = No FIFO full error 1 = FIFO was full during a write to FIFO. The FIFO full error flag is set when the current line of VBI data can not enter the FIFO. For example, if the FIFO has only ten bytes left and teletext is the current VBI line, the FIFO full error flag is set, but no data is written because the entire teletext line will not fit. However, if the next VBI line is closed caption requiring only two bytes of data plus the header, this goes into the FIFO (even if the full error flag is set). FIFO empty: 0 = FIFO is not empty. 1 = FIFO is empty. TTX available: 0 = Teletext data is not available. 1 = Teletext data is available. CC field 1 available: 0 = Closed caption data from field 1 is not available. 1 = Closed caption data from field 1 is available. CC field 2 available: 0 = Closed caption data from field 2 is not available. 1 = Closed caption data from field 2 is available. WSS available: 0 = WSS data is not available. 1 = WSS data is available. VPS available 0 = VPS data is not available. 1 = VPS data is available. VITC available: 0 = VITC data is not available. 1 = VITC data is available. 9.2.65 Address FIFO Word Count Register C7h 7 6 5 4 3 2 1 0 1 0 Number of words This register provides the number of words in the FIFO. One word equals two bytes. 9.2.66 FIFO Interrupt Threshold Register Address C8h Default 80h 7 6 5 4 3 2 Number of words This register is programmed to trigger an interrupt when the number of words in the FIFO exceeds this value (default 80h). This interrupt must be enabled at address C1h. One word equals two bytes. Submit Documentation Feedback Internal Control Registers 55 TVP5154 4-CHANNEL LOW-POWER PAL/NTSC/SECAM VIDEO DECODER WITH INDEPENDENT SCALERS AND FAST LOCK www.ti.com SLES163A – MARCH 2006 – REVISED JULY 2006 9.2.67 FIFO Reset Register Address C9h Default 00h 7 6 5 4 3 2 1 0 Any data Writing any data to this register resets the FIFO and clears any data present in both the FIFO and the VDP registers. 9.2.68 Line Number Interrupt Register Address CAh Default 00h 7 6 Field 1 enable Field 2 enable 5 4 3 2 1 0 Line number This register is programmed to trigger an interrupt when the video line number matches this value in bits 5:0. This interrupt must be enabled at address C1h. The value of 0 or 1 does not generate an interrupt. Field 1 enable: 0 = Disabled (default) 1 = Enabled Field 2 enable: 0 = Disabled (default) 1 = Enabled Line number: (default 00h) 9.2.69 Pixel Alignment Registers Address CBh CCh Default 4Eh 00h Address 7 6 5 4 CBh 3 2 1 0 Switch pixel [7:0] CCh Reserved Switch pixel [9:8] These registers form a 10-bit horizontal pixel position from the falling edge of sync, where the VDP controller initiates the program from one line standard to the next line standard; for example, the previous line of teletext to the next line of closed caption. This value must be set so that the switch occurs after the previous transaction has cleared the delay in the VDP, but early enough to allow the new values to be programmed before the current settings are required. 9.2.70 FIFO Output Control Register Address CDh Default 01h 7 6 5 4 3 2 1 0 Reserved Host access enable I2C This register is programmed to allow access to the FIFO or allowing all VDP data to go out the video port. Host access enable: 0 = Output FIFO data to the video output Y[7:0] 1 = Allow I2C access to the FIFO data (default) 56 Internal Control Registers Submit Documentation Feedback TVP5154 4-CHANNEL LOW-POWER PAL/NTSC/SECAM VIDEO DECODER WITH INDEPENDENT SCALERS AND FAST LOCK www.ti.com SLES163A – MARCH 2006 – REVISED JULY 2006 9.2.71 Full Field Enable Register Address CFh Default 00h 7 6 5 4 Reserved 3 2 1 0 Full field enable This register enables the full field mode. In this mode, all lines outside the vertical blank area and all lines in the line mode registers programmed with FFh are sliced with the definition of register FCh. Values other than FFh in the line mode registers allow a different slice mode for that particular line. Full field enable: 0 = Disable full field mode (default) 1 = Enable full field mode 9.2.72 Line Mode Registers Address D0h D1h–FBh Default 00h FFh Submit Documentation Feedback Internal Control Registers 57 TVP5154 4-CHANNEL LOW-POWER PAL/NTSC/SECAM VIDEO DECODER WITH INDEPENDENT SCALERS AND FAST LOCK www.ti.com SLES163A – MARCH 2006 – REVISED JULY 2006 Address 58 7 6 5 4 3 D0h Line 6 Field 1 D1h Line 6 Field 2 D2h Line 7 Field 1 D3h Line 7 Field 2 D4h Line 8 Field 1 D5h Line 8 Field 2 D6h Line 9 Field 1 D7h Line 9 Field 2 D8h Line 10 Field 1 D9h Line 10 Field 2 DAh Line 11 Field 1 DBh Line 11 Field 2 DCh Line 12 Field 1 DDh Line 12 Field 2 DEh Line 13 Field 1 DFh Line 13 Field 2 E0h Line 14 Field 1 E1h Line 14 Field 2 E2h Line 15 Field 1 E3h Line 15 Field 2 E4h Line 16 Field 1 E5h Line 16 Field 2 E6h Line 17 Field 1 E7h Line 17 Field 2 E8h Line 18 Field 1 E9h Line 18 Field 2 EAh Line 19 Field 1 EBh Line 19 Field 2 ECh Line 20 Field 1 EDh Line 20 Field 2 EEh Line 21 Field 1 EFh Line 21 Field 2 F0h Line 22 Field 1 F1h Line 22 Field 2 F2h Line 23 Field 1 F3h Line 23 Field 2 F4h Line 24 Field 1 F5h Line 24 Field 2 F6h Line 25 Field 1 F7h Line 25 Field 2 F8h Line 26 Field 1 F9h Line 26 Field 2 FAh Line 27 Field 1 FBh Line 27 Field 2 Internal Control Registers 2 1 0 Submit Documentation Feedback www.ti.com TVP5154 4-CHANNEL LOW-POWER PAL/NTSC/SECAM VIDEO DECODER WITH INDEPENDENT SCALERS AND FAST LOCK SLES163A – MARCH 2006 – REVISED JULY 2006 These registers program the specific VBI standard at a specific line in the video field. Bit 7: 0 = Disable filtering of null bytes in closed caption modes. 1 = Enable filtering of null bytes in closed caption modes (default). In teletext modes, bit 7 enables the data filter function for that particular line. If it is set to 0, the data filter passes all data on that line. Bit 6: 0 = Send VBI data to registers only. 1 = Send VBI data to FIFO and the registers. Teletext data only goes to FIFO. (default) Bit 5: 0 = Allow VBI data with errors in the FIFO. 1 = Do not allow VBI data with errors in the FIFO (default). Bit 4: 0 = Do not enable error detection and correction. 1 = Enable error detection and correction (when bits [3:0] = 1 2, 3, and 4 only) (default). Bits [3:0]: 0000 = WST SECAM 0001 = WST PAL B 0010 = WST PAL C 0011 = WST NTSC 0100 = NABTS NTSC C 0101 = NABTS NTSC D 0110 = CC PAL 0111 = CC NTSC 1000 = WSS PAL 1001 = WSS NTSC 1010 = VITC PAL 1011 = VITC NTSC 1100 = VPS PAL 1101 = Custom 1 1110 = Custom 2 1111 = Active video (VDP off) (default) A value of FFh in the line mode registers is required for any line to be sliced as part of the full field mode. Submit Documentation Feedback Internal Control Registers 59 TVP5154 4-CHANNEL LOW-POWER PAL/NTSC/SECAM VIDEO DECODER WITH INDEPENDENT SCALERS AND FAST LOCK www.ti.com SLES163A – MARCH 2006 – REVISED JULY 2006 9.2.73 Full Field Mode Register Address FCh Default 7Fh 7 6 5 4 3 2 1 0 Full field mode This register programs the specific VBI standard for full field mode. It can be any VBI standard. Individual line settings take priority over the full field register. This allows each VBI line to be programmed independently but have the remaining lines in full field mode. The full field mode register has the same definitions as the line mode registers (default 7Fh). 9.2.74 Decoder Write Enable Address FEh Default 0Fh 7 6 5 4 Reserved 3 2 1 0 Decoder 4 Decoder 3 Decoder 2 Decoder 1 This register controls which of the four decoder cores receives I2C write transactions. A 1 in the corresponding bit position enables the decoder to receive write commands. Any combination of decoders can be configured to receive write commands, allowing all four decoders to be programmed concurrently. 9.2.75 Decoder Read Enable Address FFh Default 00h 7 6 5 Reserved 4 3 2 1 0 Decoder 4 Decoder 3 Decoder 2 Decoder 1 This register controls which of the four decoder cores responds to I2C read transactions. A 1 in the corresponding bit position enables the decoder to respond to read commands. If more than one decoder is enabled for reading, only the lowest numbered decoder responds. Reads from multiple decoders at the same time is not possible. Note that when register 0xFE is written to with any value, register 0xFF is set to 0x00. Likewise, when register 0xFF is written to with any value, register 0xFE is set to 0x00. 9.3 Indirect Register Definitions To write to the TVP5154 indirect registers, it is required that the registers be unlocked using a password. The password prevents undesirable writes into the device at start-up due to power surges, for example. The following example demonstrates the method for unlocking the indirect registers. After writing to the desired indirect registers described in the following text, it is recommended that the device be locked again. • Unlock the device 1. Write 0x51 to I2C_0x21. //MSB data 2. Write 0x54 to I2C_0x22. //LSB data 3. Write 0xFF to I2C_0x23. //Data address 4. Write 0x04 to I2C_0x24. //Write command 60 Internal Control Registers Submit Documentation Feedback TVP5154 4-CHANNEL LOW-POWER PAL/NTSC/SECAM VIDEO DECODER WITH INDEPENDENT SCALERS AND FAST LOCK www.ti.com SLES163A – MARCH 2006 – REVISED JULY 2006 • Lock the device 1. Write 0x00 to I2C_0x21. //MSB data 2. Write 0x00 to I2C_0x22. //LSB data 3. Write 0xFF to I2C_0x23. //Data address 4. Write 0x04 to I2C_0x24. //Write command Indirect registers are written to by performing the following I2C transaction: START : DEVICE_ID_w : 0x21 : DATA_HIGH : STOP START : DEVICE_ID_w : 0x22 : DATA_LOW : STOP START : DEVICE_ID_w : 0x23 : ADDRESS_LOW : STOP START : DEVICE_ID_w : 0x24 : WR_STROBE : STOP To read from an indirect register, the following I2C transaction should be performed: START : DEVICE_ID_w : 0x23 : ADDRESS_LOW : STOP START : DEVICE_ID_w : 0x24 : RD_STROBE : STOP START : DEVICE_ID_r : 0x21 : data_msb : STOP START : DEVICE_ID_r : 0x22 : data_lsb : STOP Where: DEVICE_ID_w is the selected TVP5154 device ID with the read/write bit (LSB) set to write. DEVICE_ID_r is the selected TVP5154 device ID with the read/write bit (LSB) set to read. ADDRESS_LOW is the low byte of the register address. WR_STROBE is 0x06. RD_STROBE is 0x05. Note, the upper byte of the address is not directly used but is replaced by the corresponding STROBE signal. Each indirect register is 16 bits wide. 9.3.1 DID Control Address 36Ah Default 000h 7 6 5 4 3 Unscaled field 1 DID 15 14 2 1 0 Unscaled field 0 DID 13 Scaled field 1 DID 12 11 10 9 8 Scaled field 0 DID This register controls the value of the EAV DID bytes for scaled and unscaled data. The value for each field can be independently set, allowing identification of both which field is being processed and whether the data comes from the scaled or unscaled channel. Submit Documentation Feedback Internal Control Registers 61 TVP5154 4-CHANNEL LOW-POWER PAL/NTSC/SECAM VIDEO DECODER WITH INDEPENDENT SCALERS AND FAST LOCK www.ti.com SLES163A – MARCH 2006 – REVISED JULY 2006 9.3.2 Misc Control Address 36Bh Default 0Ch 7 6 15 14 5 4 3 13 12 11 Clock rate 2 1 10 9 Clock OE 0 Clock edge 8 Scaled blank data Scaled blank data: When no active scaled data is available, this value is output during the active video region. Clock rate: This register controls various clock modes. Since this register is modified by the device during normal operation, the clock rate bits should not be modified by the user. Clock OE: This register controls various clock modes. Since this register is modified by the device during normal operation, the clock rate bits should not be modified by the user. Clock edge: This register controls various clock modes. Since this register is modified by the device during normal operation, the clock rate bits should not be modified by the user. 9.3.3 Interleave Field Control 1 Address 36Dh Default 0h 7 6 5 4 3 2 1 0 11 10 9 8 Reserved Blank timing End pixel count[7:0] 15 14 13 12 Field count End pixel count[9:8] End pixel count: Pixel count at which the frame status is updated. Do not change this value. Blank timing: 0: No timing signals are generated for blank fields. 1: H, V, and F timing generated for blank fields based on unscaled video timing sequences Field count: Number of output fields in field interleaved sequence 9.3.4 Interleave Field Control 2 Address 36Eh Default 0h 7 6 5 Field mode(3) 15 14 13 Field mode(7) 9.3.5 3 2 1 Field mode(1) 12 11 Field mode(6) 0 Field mode(0) 10 9 Field mode(5) 8 Field mode(4) Interleave Field Control 3 Address 36Fh Default 0h 7 6 5 14 13 Field mode(11) 15 4 3 12 11 Field mode(10) Field mode(15) 62 4 Field mode(2) Internal Control Registers Field mode(14) 2 1 10 9 Field mode(9) Field mode(13) 0 Field mode(8) 8 Field mode(12) Submit Documentation Feedback TVP5154 4-CHANNEL LOW-POWER PAL/NTSC/SECAM VIDEO DECODER WITH INDEPENDENT SCALERS AND FAST LOCK www.ti.com SLES163A – MARCH 2006 – REVISED JULY 2006 These registers allow the output data stream to toggle between unscaled and scaled data on a field basis. By setting Field mode[n] appropriately, it is possible to use the available output bandwidth to interleave unscaled and scaled frames to achieve reduced frame rates, while still maintaining compatibility with legacy data receivers. These registers can also be used to reduce the frame rate of either unscaled data or scaled data by disabling fields within the sequence. A counter automatically moves from Field mode[0] to Field mode[n] where n can be 0 through 15, then returns back to Field mode[0]. Depending on the value of Field mode[n], either unscaled data, scaled data, or no data is sent for the current frame. 00 = Unscaled data 01 = Null frame (no SAV/EAV sequence will be generated) 10 = Scaled data 11 = Reserved The values programmed for registers 3A8h and 3A9h are different for NTSC (also NTSC4.43 and PAL-M) and for PAL (also PAL-Nc and SECAM). 9.3.6 Vertical Scaling Field 1 Control Address 3A8h Default 0h 7 6 5 4 3 2 1 11 10 9 0 V_Field1[7:0] 15 14 13 12 Reserved 8 V_Field1[8] Vertical scaling initial value in field 1 [8:0]: Initial value of vertical accumulator for field 1 For NTSC: V_Field1 = (1.5 × V_Field2) – 128 If V_Field 1 is negative, add V_Field2 to V_Field1 and add V_Field2 to V_Field2 until V_Field1 is positive. For PAL: V_Field1 = (Vdesired/Vactive) × 256 9.3.7 Vertical Scaling Field 2 Control Address 3A9h Default 0h 7 6 5 4 15 14 13 12 3 2 1 11 10 9 0 V_Field2[7:0] Reserved 8 V_Field2[8] Vertical scaling initial value in field 2 [8:0]: Initial value of vertical accumulator for field 2 For NTSC: V_Field2 = (Vdesired/Vactive) × 256 For PAL: V_Field2 = (1.5 × V_Field1) – 128 If V_Field 2 is negative, add V_Field1 to V_Field2 and add V_Field1 to V_Field1 until V_Field2 is positive. 9.3.8 Scaler Output Active Pixels Address 3ABh Default 2D0h 7 6 5 4 3 2 1 0 10 9 8 SCAL_PIXEL[7:0] 15 14 13 12 Reserved 11 SCAL_PIXEL[9:8] SCAL_PIXEL [9:0]: Scaler active pixel outputs per line Submit Documentation Feedback Internal Control Registers 63 TVP5154 4-CHANNEL LOW-POWER PAL/NTSC/SECAM VIDEO DECODER WITH INDEPENDENT SCALERS AND FAST LOCK www.ti.com SLES163A – MARCH 2006 – REVISED JULY 2006 9.3.9 Vertical Scaling Control Address 3ACh Default 2100h 7 6 5 4 3 2 1 10 9 0 VERT_COEF[7:0] 15 14 Reserved 13 12 1 Enable 11 Reserved 8 VERT_COEF[8] Enabled: Enable vertical and horizontal scaler 0 = Disable scaler (default) 1 = Enable scaler VERT_COEF [8:0]: Vertical scaling coefficient VERT_COEF = (Vdesired/Vactive) × 256 9.3.10 Horizontal Scaling Control Address 3ADh Default 400h 7 6 5 4 3 2 1 0 10 9 8 HORZ_COEF[7:0] 15 14 Reserved HORZ_COEF[14:0]: 13 12 11 HORZ_COEF[14:8] Horizontal scaling coefficient, MSB five bits are integer values and LSB ten bits are fraction numbers. HORZ_COEF = Hactive/Hdesired 10 Scaler Configuration 10.1 Overview The TVP5154 contains four independent scalers, one for each video decoder channel. Each scaler is able to filter and scale both horizontally and vertically to different ratios. Horizontally, a 7-tap poly-phase filter is used to ensure optimal scaling performance, and can be configured to scale to any output size below the input resolution, in decrements of two pixels. Vertically a running average filter is used to filter vertically and can be configured to scale to any output size below the input resolution. When scaling horizontally, the output pixels are packed together to allow continuous reading of the pixels. AVID should be configured so that it qualifies the active pixels, allowing the receiving back end to ignore nonactive pixels. When scaling vertically, inactive lines are not removed from the output since there is no internal frame memory. The receiving back end must use AVID to qualify active lines/pixels. AVID can be configured to be either active or inactive during invalid output lines. Due to the fact that vertical scaling is performed on a field basis, it is possible that the vertical resolution will be reduced due to filtering across lines within the field, rather than adjacent lines in the frame. Aliasing will not occur, but the output image will appear soft vertically. If the desired scaling ration is 0.5, this can be achieved by simply ignoring every other field. This maintains sharpness, but may introduce aliasing artifacts. 64 Scaler Configuration Submit Documentation Feedback TVP5154 4-CHANNEL LOW-POWER PAL/NTSC/SECAM VIDEO DECODER WITH INDEPENDENT SCALERS AND FAST LOCK www.ti.com SLES163A – MARCH 2006 – REVISED JULY 2006 10.2 Horizontal Scaling 10.2.1 Registers The horizontal scaler uses a 32-phase polymorphic filter. Excellent performance can be achieved by using the set of coefficients programmed into the 5154 for all scaling ratios. It is necessary to program the input and output scaling control registers (3AB and 3AD). Figure 10-1 shows how data is packed horizontally when scaled. Unscaled SAV EAV Scaled SAV EAV Figure 10-1. Unscaled and Scaled Pixel Data Alignment 10.3 Vertical Scaling 10.3.1 Registers The vertical scaler implements a weighted running average filter, which requires the initial weights and the ratio registers to be configured. Additionally, it is necessary to program the input and output scaling control registers (3A8, 3A9, and 3AC). Figure 10-2 shows the active and inactive data lines when scaled vertically. Unscaled Un Line n SAV EAV Line n+1 SAV EAV Line n+2 SAV EAV Line n+3 SAV EAV Line n+4 SAV EAV Line n+5 SAV EAV Line n+6 SAV EAV Line n+7 SAV EAV Scaled Line n SAV EAV Line n+1 SAV EAV Line n+3 SAV EAV Line n+4 SAV EAV Line n+6 SAV EAV Line n+7 SAV EAV Line n+2 Line n+5 Figure 10-2. Unscaled and Scaled Vertical Data Formatting Submit Documentation Feedback Scaler Configuration 65 TVP5154 4-CHANNEL LOW-POWER PAL/NTSC/SECAM VIDEO DECODER WITH INDEPENDENT SCALERS AND FAST LOCK www.ti.com SLES163A – MARCH 2006 – REVISED JULY 2006 10.4 Field Interleaving In systems where either there are insufficient video ports on the back end processor to accommodate both scaled and unscaled video streams, or where the back end processor does not have sufficient processing power to perform compression on the unscaled image at the same time as other video processing, such as composting of scaled images for display, it is possible to configure the TVP5154 to output different image types on consecutive fields. In this configuration, the field rates for each of the scaled and unscaled images is reduced to accommodate the interleaving of fields, while maintaining a 27-MHz pixel clock. This is useful in video recording systems that are required to display a scaled image but still wish to compress and store full resolution images, albeit at reduced field rates. Field interleaving can generate a sequence of up to 16 fields, where each field can be either unscaled, scaled, or blank. 10.4.1 Registers The field loop count register controls how many fields are in the sequence. The field mode registers control the output field type for each field. Figure 10-3 shows how to configure field interleaving for a sequence of five fields where the first field is unscaled, the second field is scaled, the third field is blank, the fourth field is scaled, and the fifth field is blank. Field 0 Field 1 Field 2 Field 3 Field 4 Field 0 Field 1 Figure 10-3. Field Interleaving Various additional registers exist to configure how the TVP5154 indicates to the back-end processor the state of the current field. The Output Control register 1Fh allows the scaled/unscaled status to be indicated by the upper bit of the SAV/EAV codes. The Output Control register 1Fh also allows the scaled/unscaled status to be indicated by the DID codes of ancillary data. 66 Scaler Configuration Submit Documentation Feedback TVP5154 4-CHANNEL LOW-POWER PAL/NTSC/SECAM VIDEO DECODER WITH INDEPENDENT SCALERS AND FAST LOCK www.ti.com SLES163A – MARCH 2006 – REVISED JULY 2006 11 Electrical Specifications Absolute Maximum Ratings (1) 11.1 over operating free-air temperature range (unless otherwise noted) VALUE Supply voltage range IOVDD to DGND –0.5 to 3.6 DVDD to DGND – 0.5 to 2 PLL_AVDD to PLL_AGND –0.5 to 2 AVDD to AGND –0.5 to 2 V Digital input voltage range, VI to DGND –0.5 to 3.6 V Input voltage range, XIN to PLL_GND –0.5 to 2 V Analog input voltage range, AI to AGND –0.2 to 2 V Digital output voltage range, VO to DGND TA Operating free-air temperature range Tstg Storage temperature range (1) UNIT –0.5 to 3.6 V 0 to 70 °C –65 to 150 °C Stresses beyond those listed under absolute maximum ratings may cause permanent damage to the device. These are stress ratings only and functional operation of the device at these or any other conditions beyond those indicated under recommended operating conditions is not implied. Exposure to absolute-maximum-rated conditions for extended periods may affect device reliability. 11.2 Recommended Operating Conditions MIN NOM MAX UNIT IOVDD Digital I/O supply voltage 3.0 3.3 3.6 V DVDD Digital supply voltage 1.65 1.8 1.95 V PLL_AVDD Analog PLL supply voltage 1.65 1.8 1.95 V AVDD Analog core supply voltage 1.65 1.8 1.95 V VI(P–P) Analog input voltage (ac-coupling necessary) 0.75 V VIH Digital input voltage high VIL Digital input voltage low VIH_XIN XIN input voltage high VIL_XIN XIN input voltage low IOH High-level output current 2 4 mA IOL Low-level output current –2 –4 mA IOH_CLK CLK high-level output current 4 8 mA IOL_CLK CLK low-level output current –4 –8 mA TA Operating free-air temperature 11.3 0 0.7 IOVDD V 0.3 IOVDD 0.7 PLL_AVDD V 0.3 PLL_AVDD 0 V 70 V °C Crystal Specifications Frequency Frequency tolerance Submit Documentation Feedback TYP UNIT 14.31818 MHz ±50 ppm Electrical Specifications 67 TVP5154 4-CHANNEL LOW-POWER PAL/NTSC/SECAM VIDEO DECODER WITH INDEPENDENT SCALERS AND FAST LOCK www.ti.com SLES163A – MARCH 2006 – REVISED JULY 2006 11.4 Electrical Characteristics For typical values: Nominal conditions, TA = 25°C For minimum/maximum values: Over recommended operating conditions (unless otherwise noted) PARAMETER TEST CONDITIONS (1) MIN TYP MAX UNIT DC I/O digital supply current at 27 MHz Color bar input (2) 46 52 mA I/O digital supply current at 54 MHz Color bar input (2) 84 90 mA Digital supply current Color bar input (2) 154 174 mA IDD(PLL_A) Analog PLL supply current Color bar input (2) 20 29 mA IDD(A) Analog core supply current Color bar input (2) 134 168 mA PTOT Total power dissipation, normal mode at 27 MHz Color bar input (2) 706 910 mW Total power dissipation, normal mode at 54 MHz Color bar input (2) 832 1050 mW IDD(IO_D) IDD(D) Ci Input capacitance (3) 10 VOH Output voltage high IOH = 2 mA VOL Output voltage low IOL = –2 mA VOH_CLK CLK output voltage high IOH = 4 mA VOL_CLK CLK output voltage low IOL = –4 mA IIH High-level input current IIL Low-level input current 0.8 IOVDD pF V 0.22 IOVDD 0.8 IOVDD V V 0.22 IOVDD V VI = VIH ±22 µA VI = VIL ±22 µA Analog Processing and ADCs (at FS = 30 MSPS) Zi Input impedance, analog video inputs By design Ci Input capacitance, analog video inputs By design VI(pp) Input voltage range (4) Ccoupling = 0.1 µF DG Gain control minimum DG Gain control maximum DNL DC differential nonlinearity A/D only INL DC integral nonlinearity A/D only Fr Frequency response 6 MHz SNR Signal-to-noise ratio 1 MHz, 0.5 VP-P 48 50 NS Noise spectrum (3) 50% flat field 48 50 dB DP Differential phase (3) Modulated ramp 1.5 deg DG Differential gain (3) Modulated ramp 0.5 % (1) (2) (3) (4) 68 200 500 kΩ 10 0 0.75 0 pF V dB 12 dB ±0.5 ±1 LSB ±1 ±2.5 LSB –0.9 –3 dB dB Measured with a load of 15 pF. For typical measurements only By design, not production tested The 0.75-V maximum applies to the sync-chroma amplitude, not sync-white. The recommended termination resistors are 37.4 Ω. Electrical Specifications Submit Documentation Feedback TVP5154 4-CHANNEL LOW-POWER PAL/NTSC/SECAM VIDEO DECODER WITH INDEPENDENT SCALERS AND FAST LOCK www.ti.com SLES163A – MARCH 2006 – REVISED JULY 2006 11.5 Timing Requirements TEST CONDITIONS (1) PARAMETER MIN Duty cycle SCL TYP MAX 50 UNIT % t1 CLK high time (at 27 MHz) 13.5 t2 CLK low time (at 27 MHz) 13.5 t3 CLK fall time (at 27 MHz) 90% to 10% t4 CLK rise time (at 27 MHz) 10% to 90% t5 Output hold time t6 Output delay time t7 Output hold time t8 Output delay time t9 Data period t10 Output hold time t11 Output delay time t12 Data period t13 CLK high time (at 54 MHz) t14 CLK low time (at 54 MHz) t15 CLK fall time (at 54 MHz) 90% to 10% 6 ns t16 CLK rise time (at 54 MHz) 10% to 90% 6 ns (1) ns ns 5 ns 5 ns 10 ns 25 4 ns ns 16.5 18.5 ns ns 4 ns 16.5 18.5 ns ns 3 ns 3 ns Measured with a load of 15 pF for 27-MHz signals, 25 pF for 54-MHz signals. By design. Timing not production tested. t1 t2 Negative edge clock Positive edge clock t3 t4 Data 1 Y/C & Syncs Data 2 t5 t6 Figure 11-1. Output Modes 0 and 1: Clocks, Video Data, and Sync t1 t2 SCLK CLK t3 Y/C & Syncs Unscaled Data 1 t4 Scaled Data 1 Unscaled Data 2 Scaled Data 2 t7 t8 t9 t9 Figure 11-2. Output Mode 2: Clocks, Video Data, and Sync Submit Documentation Feedback Electrical Specifications 69 TVP5154 4-CHANNEL LOW-POWER PAL/NTSC/SECAM VIDEO DECODER WITH INDEPENDENT SCALERS AND FAST LOCK www.ti.com SLES163A – MARCH 2006 – REVISED JULY 2006 t13 t14 CLK t15 Y/C & Syncs Scaled Data 1 Unscaled Data 1 t16 Unscaled Data 2 Scaled Data 2 t10 t11 t12 t12 Figure 11-3. Output Mode 3: Clock, Video Data, and Sync (Positive Edge Clock) 70 Electrical Specifications Submit Documentation Feedback TVP5154 4-CHANNEL LOW-POWER PAL/NTSC/SECAM VIDEO DECODER WITH INDEPENDENT SCALERS AND FAST LOCK www.ti.com SLES163A – MARCH 2006 – REVISED JULY 2006 11.6 I2C Host Port Timing PARAMETER TEST CONDITIONS MIN MAX UNIT t1 Bus free time, between STOP and START 1.3 µs t2 Setup time, (repeated) START condition 0.6 µs t3 Hold time, (repeated) START condition 0.6 µs t4 Setup time, STOP condition 0.6 ns t5 Data setup time 100 t6 Data hold time t7 Rise time, VC1(SDA) and VC0(SCL) signal t8 Cb fI2C I2C clock frequency ns 0.9 µs Specified by design 250 ns Fall time, VC1(SDA) and VC0(SCL) signal Specified by design 250 ns Capacitive load for each bus line Specified by design 400 pF 400 kHz 0 Stop Start VC1 (SDA) Stop Data t1 t3 t7 t3 t5 t6 t8 t2 t4 VC0 (SCL) Figure 11-4. I2C Host Port Timing Submit Documentation Feedback Electrical Specifications 71 A B 1 37.4 R 37.4 R 37.4 R 37.4 R R 37.4 R 37.4 R 37.4 R 37.4 CH4_A CH3_A CH2_A CH1_A CH4_B IN CH3_B IN CH2_B IN CH1_B IN I2CA0 R 10k 2 R 10k IOVDD I2CA1 R 10k 2 R 10k IOVDD 2-3 Base Addr 0xB8 - Default I2C ADDRESS SELECTION CH4_A IN CH3_A IN CH2_A IN CH1_A IN 1 3 C C 0.1uF C 0.1uF REMEMBER 75ohm TERMINATION FOR 0-0.75V INPUT RANGE INPUT V DIVIDER NETWORK C 0.1uF DVDD 1 3 D C 0.1uF PLL_VDD C 0.1uF C 0.1uF 37.4 R 37.4 R 37.4 R 37.4 R C 0.1uF C 0.1uF 2 R 37.4 R 37.4 R 37.4 R 37.4 CH4_B CH3_B CH2_B CH1_B C 0.1uF C 0.1uF TMS R 10k R 100 IOVDD C CH1_B 0.1uF 0.1uF C CH2_B 0.1uF 0.1uF C CH3_B 0.1uF 0.1uF 0.1uF 0.1uF C C CH4_A CH4_B REFM4 REFP4 C CH3_A REFM3 REFP3 C CH2_A REFM2 REFP2 C CH1_A C 1uF PLL_VDD AVDD REFM1 C 0.1uF 1uF C 3 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 C 1uF TVP5154PNP AI1GND AI1A AI1B PLL_VDD PLL_GND REFM2 REFP2 AVDD AGND AI2GND AI2A AI2B PLL_VDD PLL_GND AVDD AGND REFM3 REFP3 AVDD AGND AI3GND AI3A AI3B PLL_VDD PLL_GND REFM4 REFP4 AVDD AGND AI4GND AI4A AI4B U1 XIN/OSC CL1 = CL2 = 2CL CSTRAY CL1 R 100k Y4 14.31818MHz TMS C 0.1uF C 1uF REFM2 3 1uF C REFP2 2 CL2 DVDD IOVDD C 1uF C 1uF REFM3 IOVDD 1uF C REFP3 AVDD REFP1 XOUT REFP1 REFM1 XIN/OSC XOUT PDN /RESET SCL SDA I2CA0 I2CA1 4 C 1uF 4 C 1uF IOGND VSYNC1/PALI1 FID1/GLCO1 CH2OUT0 CH2OUT1 CH2OUT2 CH2OUT3 CH2OUT4 CH2OUT5 CH2OUT6 CH2OUT7 SCLK2 CLK2 INT2/GPCL2/VBLK2 DGND DVDD IOVDD IOGND AVID2 HSYNC2 VSYNC2/PALI2 FID2/GLCO2 CH3OUT0 CH3OUT1 CH3OUT2 CH3OUT3 CH3OUT4 CH3OUT5 CH3OUT6 CH3OUT7 DGND DVDD 128 127 126 125 124 123 122 121 120 119 118 117 116 115 114 113 112 111 110 109 108 107 106 105 104 103 102 101 100 99 98 97 AGND AVDD REFP1 REFM1 XIN/OSC XOUT PDN RESETB SCL SDA I2CA0 I2CA1 DGND DVDD IOVDD IOGND CH1OUT0 CH1OUT1 CH1OUT2 CH1OUT3 CH1OUT4 CH1OUT5 CH1OUT6 CH1OUT7 SCLK1 CLK1 INT1/GPCL1/VBLK1 AVID1 HSYNC1 DGND DVDD IODVDD PLL_VDD PLL_GND AGND TMS FID4/GLCO4 VSYNC4/PALI4 HSYNC4 AVID4 INT4/GPCL4/VBLK4 CLK4 SCLK4 IOGND IOVDD DVDD DGND CH4OUT7 CH4OUT6 CH4OUT5 CH4OUT4 CH4OUT3 CH4OUT2 CH4OUT1 CH4OUT0 FID3/GLCO3 VSYNC3/PALI3 HSYNC3 AVID3 INT4/GPCL4/VBLK4 CLK3 SCLK3 IOGND IOVDD 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 Schematic REFM4 72 1uF C 96 95 94 93 92 91 90 89 88 87 86 85 84 83 82 81 80 79 78 77 76 75 74 73 72 71 70 69 68 67 66 65 REFP4 1 C 1uF CH4_D0 CH4_D1 CH4_D2 CH4_D3 CH4_D4 CH4_D5 CH4_D6 CH4_D7 CH3_D0 CH3_D1 CH3_D2 CH3_D3 CH3_D4 CH3_D5 CH3_D6 CH3_D7 CH2_D0 CH2_D1 CH2_D2 CH2_D3 CH2_D4 CH2_D5 CH2_D6 CH2_D7 CH1_D0 CH1_D1 CH1_D2 CH1_D3 CH1_D4 CH1_D5 CH1_D6 CH1_D7 SCLK4 CLK4 GPCL4/VBLK4 AVID4 HSYNC4 VSYNC4/PALI4 FID4/GLCO4 SCLK3 CLK3 GPCL3/VBLK3 AVID3 HSYNC3 VSYNC3/PALI3 FID3/GLCO3 AVID2 HSYNC2 VSYNC2/PALI2 FID2/GLCO2 SCLK2 CLK2 GPCL2/VBLK2 SCLK1 CLK1 GPCL1/VBLK1 AVID1 HSYNC1 VSYNC1/PALI1 FID1/GLCO1 5 5 Scale Size C FCSM No. TVP5154 TEXAS INSTRUMENTS, INC. 12500 TI BLVD DALLAS, TEXAS 75243 RPACK8-33 Sheet /RESET SDA SCL SCK4 CK4 VB4 AV4 HS4 VS4 FID4 RPACK8-33 CH4_OUT0 CH4_OUT1 CH4_OUT2 CH4_OUT3 CH4_OUT4 CH4_OUT5 CH4_OUT6 CH4_OUT7 RPACK8-33 SCK3 CK3 VB3 AV3 HS3 VS3 FID3 RPACK8-33 CH3_OUT0 CH3_OUT1 CH3_OUT2 CH3_OUT3 CH3_OUT4 CH3_OUT5 CH3_OUT6 CH3_OUT7 RPACK8-33 SCK2 CK2 VB2 AV2 HS2 VS2 FID2 RPACK8-33 CH2_OUT0 CH2_OUT1 CH2_OUT2 CH2_OUT3 CH2_OUT4 CH2_OUT5 CH2_OUT6 CH2_OUT7 RPACK8-33 SCK1 CK1 VB1 AV1 HS1 VS1 FID1 RPACK8-33 CH1_OUT0 CH1_OUT1 CH1_OUT2 CH1_OUT3 CH1_OUT4 CH1_OUT5 CH1_OUT6 CH1_OUT7 DWG No. SCLK4 CLK4 GPCL4/VBLK4 AVID4 HSYNC4 VSYNC4/PALI4 FID4/GLCO4 CH4_D0 CH4_D1 CH4_D2 CH4_D3 CH4_D4 CH4_D5 CH4_D6 CH4_D7 SCLK3 CLK3 GPCL3/VBLK3 AVID3 HSYNC3 VSYNC3/PALI3 FID3/GLCO3 CH3_D0 CH3_D1 CH3_D2 CH3_D3 CH3_D4 CH3_D5 CH3_D6 CH3_D7 SCLK2 CLK2 GPCL2/VBLK2 AVID2 HSYNC2 VSYNC2/PALI2 FID2/GLCO2 CH2_D0 CH2_D1 CH2_D2 CH2_D3 CH2_D4 CH2_D5 CH2_D6 CH2_D7 SCLK1 CLK1 GPCL1/VBLK1 AVID1 HSYNC1 VSYNC1/PALI1 FID1/GLCO1 CH1_D0 CH1_D1 CH1_D2 CH1_D3 CH1_D4 CH1_D5 CH1_D6 CH1_D7 6 2 of 17 /RESET SDA SCL SCK4 CK4 VB4 AV4 HS4 VS4 FID4 CH4_OUT[7..0] SCK3 CK3 VB3 AV3 HS3 VS3 FID3 CH3_OUT[7..0] SCK2 CK2 VB2 AV2 HS2 VS2 FID2 CH2_OUT[7..0] SCK1 CK1 VB1 AV1 HS1 VS1 FID1 CH1_OUT[7..0] 6 Rev 1 CH4_OUT[7..0] CH3_OUT[7..0] CH2_OUT[7..0] CH1_OUT[7..0] A B C D TVP5154 4-CHANNEL LOW-POWER PAL/NTSC/SECAM VIDEO DECODER WITH INDEPENDENT SCALERS AND FAST LOCK SLES163A – MARCH 2006 – REVISED JULY 2006 www.ti.com 12 Schematic Submit Documentation Feedback www.ti.com TVP5154 4-CHANNEL LOW-POWER PAL/NTSC/SECAM VIDEO DECODER WITH INDEPENDENT SCALERS AND FAST LOCK SLES163A – MARCH 2006 – REVISED JULY 2006 13 MECHANICAL Submit Documentation Feedback MECHANICAL 73 TVP5154 4-CHANNEL LOW-POWER PAL/NTSC/SECAM VIDEO DECODER WITH INDEPENDENT SCALERS AND FAST LOCK www.ti.com SLES163A – MARCH 2006 – REVISED JULY 2006 74 MECHANICAL Submit Documentation Feedback PACKAGE OPTION ADDENDUM www.ti.com 13-Jun-2006 PACKAGING INFORMATION Orderable Device Status (1) Package Type Package Drawing Pins Package Eco Plan (2) Qty TVP5154PNP ACTIVE HTQFP PNP 128 90 Green (RoHS & no Sb/Br) CU NIPDAU Level-3-260C-168 HR TVP5154PNPG4 ACTIVE HTQFP PNP 128 90 Green (RoHS & no Sb/Br) CU NIPDAU Level-3-260C-168 HR TVP5154PNPR ACTIVE HTQFP PNP 128 1000 Green (RoHS & no Sb/Br) CU NIPDAU Level-3-260C-168 HR TVP5154PNPRG4 ACTIVE HTQFP PNP 128 1000 Green (RoHS & no Sb/Br) CU NIPDAU Level-3-260C-168 HR Lead/Ball Finish MSL Peak Temp (3) (1) The marketing status values are defined as follows: ACTIVE: Product device recommended for new designs. LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect. NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in a new design. PREVIEW: Device has been announced but is not in production. Samples may or may not be available. OBSOLETE: TI has discontinued the production of the device. (2) Eco Plan - The planned eco-friendly classification: Pb-Free (RoHS), Pb-Free (RoHS Exempt), or Green (RoHS & no Sb/Br) - please check http://www.ti.com/productcontent for the latest availability information and additional product content details. TBD: The Pb-Free/Green conversion plan has not been defined. Pb-Free (RoHS): TI's terms "Lead-Free" or "Pb-Free" mean semiconductor products that are compatible with the current RoHS requirements for all 6 substances, including the requirement that lead not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered at high temperatures, TI Pb-Free products are suitable for use in specified lead-free processes. Pb-Free (RoHS Exempt): This component has a RoHS exemption for either 1) lead-based flip-chip solder bumps used between the die and package, or 2) lead-based die adhesive used between the die and leadframe. The component is otherwise considered Pb-Free (RoHS compatible) as defined above. Green (RoHS & no Sb/Br): TI defines "Green" to mean Pb-Free (RoHS compatible), and free of Bromine (Br) and Antimony (Sb) based flame retardants (Br or Sb do not exceed 0.1% by weight in homogeneous material) (3) MSL, Peak Temp. -- The Moisture Sensitivity Level rating according to the JEDEC industry standard classifications, and peak solder temperature. Important Information and Disclaimer:The information provided on this page represents TI's knowledge and belief as of the date that it is provided. TI bases its knowledge and belief on information provided by third parties, and makes no representation or warranty as to the accuracy of such information. Efforts are underway to better integrate information from third parties. TI has taken and continues to take reasonable steps to provide representative and accurate information but may not have conducted destructive testing or chemical analysis on incoming materials and chemicals. TI and TI suppliers consider certain information to be proprietary, and thus CAS numbers and other limited information may not be available for release. In no event shall TI's liability arising out of such information exceed the total purchase price of the TI part(s) at issue in this document sold by TI to Customer on an annual basis. Addendum-Page 1 IMPORTANT NOTICE Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, modifications, enhancements, improvements, and other changes to its products and services at any time and to discontinue any product or service without notice. Customers should obtain the latest relevant information before placing orders and should verify that such information is current and complete. All products are sold subject to TI’s terms and conditions of sale supplied at the time of order acknowledgment. TI warrants performance of its hardware products to the specifications applicable at the time of sale in accordance with TI’s standard warranty. Testing and other quality control techniques are used to the extent TI deems necessary to support this warranty. Except where mandated by government requirements, testing of all parameters of each product is not necessarily performed. TI assumes no liability for applications assistance or customer product design. Customers are responsible for their products and applications using TI components. To minimize the risks associated with customer products and applications, customers should provide adequate design and operating safeguards. TI does not warrant or represent that any license, either express or implied, is granted under any TI patent right, copyright, mask work right, or other TI intellectual property right relating to any combination, machine, or process in which TI products or services are used. Information published by TI regarding third-party products or services does not constitute a license from TI to use such products or services or a warranty or endorsement thereof. Use of such information may require a license from a third party under the patents or other intellectual property of the third party, or a license from TI under the patents or other intellectual property of TI. Reproduction of information in TI data books or data sheets is permissible only if reproduction is without alteration and is accompanied by all associated warranties, conditions, limitations, and notices. Reproduction of this information with alteration is an unfair and deceptive business practice. TI is not responsible or liable for such altered documentation. Resale of TI products or services with statements different from or beyond the parameters stated by TI for that product or service voids all express and any implied warranties for the associated TI product or service and is an unfair and deceptive business practice. TI is not responsible or liable for any such statements. Following are URLs where you can obtain information on other Texas Instruments products and application solutions: Products Applications Amplifiers amplifier.ti.com Audio www.ti.com/audio Data Converters dataconverter.ti.com Automotive www.ti.com/automotive DSP dsp.ti.com Broadband www.ti.com/broadband Interface interface.ti.com Digital Control www.ti.com/digitalcontrol Logic logic.ti.com Military www.ti.com/military Power Mgmt power.ti.com Optical Networking www.ti.com/opticalnetwork Microcontrollers microcontroller.ti.com Security www.ti.com/security Low Power Wireless www.ti.com/lpw Mailing Address: Telephony www.ti.com/telephony Video & Imaging www.ti.com/video Wireless www.ti.com/wireless Texas Instruments Post Office Box 655303 Dallas, Texas 75265 Copyright 2006, Texas Instruments Incorporated