TVP5154A www.ti.com SLES214C – DECEMBER 2007 – REVISED SEPTEMBER 2010 4-Channel Low-Power PAL/NTSC/SECAM Video Decoder With Independent Scalers and Fast Lock Check for Samples: TVP5154A 1 Introduction 1.1 Features 1 • Four Separate Video Decoder Channels With Features for Each Channel: – Accept NTSC (J, M, 4.43), PAL (B, D, G, H, I, M, N, Nc), and SECAM (B, D, G, K, K1, L) Video – Support ITU-R BT.601 Standard Sampling – High-Speed 9-Bit Analog-to-Digital Converter (ADC) – Two Composite Inputs or One S-Video Input (for Each Channel) – Fully Differential CMOS Analog Preprocessing Channels With Clamping and Automatic Gain Control (AGC) for Best Signal to Noise (SNR) Performance – Brightness, Contrast, Saturation, Hue, and Sharpness Control Through Inter-Integrated Circuit (I2C) – Complementary 4-Line (3-H Delay) Adaptive Comb Filters for Both Cross-Luminance and Cross-Chrominance Noise Reduction – Patented Architecture for Locking to Weak, Noisy, or Unstable Signals • Four Independent Polymorphic Scalers • Single or Concurrent Scaled and Unscaled Outputs Via Dual Clocking Data, Interleaved 54-MHz Data or Single 27-MHz Clock • Scaled/Unscaled Image Toggle Mode Gives Variable Field Rate for Both Scaled and Unscaled Video • Low Power Consumption: 700 mW Typical • 128-Pin Thin Quad Flat Pack (TQFP) Package • Single 14.31818-MHz Crystal for All Standards and All Channels 1.2 • Internal Phase-Locked Loop (PLL) for Line-Locked Clock (Separate for Each Channel) and Sampling • Sub-Carrier Genlock Output for Synchronizing Color Sub-Carrier of External Encoder • Standard Programmable Video Output Format – ITU-R BT.656, 8-Bit 4:2:2 With Embedded Syncs – 8-Bit 4:2:2 With Discrete Syncs • Advanced Programmable Video Output Formats – 2× Over-Sampled Raw Vertical Blanking Interval (VBI) Data During Active Video – Sliced VBI Data During Horizontal Blanking or Active Video • VBI Modes Supported: – Teletext (NABTS, WST) – Closed-Caption Decode With FIFO, and Extended Data Services (EDS) – Wide Screen Signaling (WSS), Video Program System (VPS), Copy Generation Management System (CGMS), Vertical Interval Time Code (VITC) – Gemstar 1×/2× Electronic Program Guide Compatible Mode – Custom Configuration Mode Allows User to Program the Slice Engine for Unique VBI Data Signals • Improved Fast Lock Mode Can Be Used When Input Video Standard Is Known and Signals on Switching Channels Are Clean • Four Possible I2C Addresses Allowing 16 Decoder Channels on a Single I2C Bus • Available in Commercial (0°C to 70°C) and Industrial (–40°C to 85°C) Temperature Ranges Description The TVP5154A device is a 4-channel, low-power, NTSC/PAL/SECAM video decoder. Available in a space-saving 128-pin thin quad flat pack (TQFP) package, each channel of the TVP5154A decoder converts NTSC, PAL, or SECAM video signals to 8-bit ITU-R BT.656 format. Discrete syncs are also 1 Please be aware that an important notice concerning availability, standard warranty, and use in critical applications of Texas Instruments semiconductor products and disclaimers thereto appears at the end of this data sheet. PRODUCTION DATA information is current as of publication date. Products conform to specifications per the terms of the Texas Instruments standard warranty. Production processing does not necessarily include testing of all parameters. Copyright © 2007–2010, Texas Instruments Incorporated TVP5154A SLES214C – DECEMBER 2007 – REVISED SEPTEMBER 2010 www.ti.com available. All four channels of the TVP5154A are independently controllable. The decoders share one crystal for all channels and for all supported standards. The TVP5154A can be programmed using a single inter-integrated circuit (I2C) serial interface. The decoder uses a 1.8-V supply for its analog and digital supplies, and a 3.3-V supply for its I/O. The optimized architecture of the TVP5154A decoder allows for low power consumption. The decoder consumes less than 720 mW of power in typical operation. Each channel of the TVP5154A is an independent video decoder with a programmable polymorphic scaler. Each channel converts baseband analog video into digital YCbCr 4:2:2 component video, which can then be scaled down to any resolution to 1/256 vertical and 15-bit horizontal in 2-pixel decrements. Composite and S-video inputs are supported. Each channel includes one 9-bit analog-to-digital converter (ADC) with 2× sampling. Sampling is ITU-R BT.601 (27.0) MHz, generated from a single 14.31818-MHz crystal or oscillator input) and is line locked. The output formats can be 8-bit 4:2:2 with discrete syncs or 8-bit ITU-R BT.656 with embedded synchronization. The TVP5154A utilizes Texas Instruments patented technology for locking to weak, noisy, or unstable signals. A real-time control (RTC) output is generated for each channel for synchronizing downstream video encoders. Complementary 4-line adaptive comb filtering is available per channel for both the luma and chroma data paths to reduce both cross-luma and cross-chroma artifacts. A chroma trap filter also is available. An improved fast lock mode can be used when the input video standard is known and the signals on the switching channels are clean. Note, switching from snow and/or noisy channels to good channels takes longer. In fast lock mode, video lock is achieved in three fields or less. Video characteristics, including hue, contrast, brightness, saturation, and sharpness, may be independently programmed for each channel using the industry standard I2C serial interface. The TVP5154A generates synchronization, blanking, lock, and clock signals in addition to digital video outputs for each channel. The TVP5154A includes methods for advanced vertical blanking interval (VBI) data retrieval. The VBI data processor slices, parses, and performs error checking on teletext, closed caption, and other data in several formats. I2C commands can be sent to one or more decoder cores simultaneously, reducing the amount of I2C activity necessary to configure each core. A register controls which decoder core receives I2C commands, and can be configured such that all four decoders receive commands at the same time. The main blocks for each of the channels of the TVP5154A decoder include: • Robust sync detector • ADC with analog processor • Y/C separation using 4-line adaptive comb filter • Independent, concurrent scaler outputs • Chrominance processor • Luminance processor • Video clock/timing processor and power-down control • I2C interface • VBI data processor 1.3 • • • • 2 Applications Security/Surveillance Digital Video Recorders/Servers and PCI Products Automotive Infotainment Video Hub Large-Format Video Wall Displays Games Systems Introduction Copyright © 2007–2010, Texas Instruments Incorporated Submit Documentation Feedback Product Folder Link(s): TVP5154A TVP5154A www.ti.com 1.4 Related Products • • • • • 1.5 SLES214C – DECEMBER 2007 – REVISED SEPTEMBER 2010 TVP5150AM1 TVP5151 TVP5146M2 TVP5147M1 TVP5158 Trademarks PowerPAD is a trademark of Texas Instruments. Macrovision is a trademark of Macrovision Corporation. Gemstar is a trademark of Gemstar-TV Guide International. Other trademarks are the property of their respective owners. 1.6 Document Conventions Throughout this data manual, several conventions are used to convey information. These conventions are: • To identify a binary number or field, a lower case b follows the numbers. For example: 000b is a 3-bit binary field. • To identify a hexadecimal number or field, a lower case h follows the numbers. For example: 8AFh is a 12-bit hexadecimal field. • All other numbers that appear in this document that do not have either a b or h following the number are assumed to be decimal format. • If the signal or terminal name has a bar above the name (for example, RESETB), then this indicates the logical NOT function. When asserted, this signal is a logic low, 0, or 0b. • RSVD indicates that the referenced item is reserved. 1.7 Ordering Information TA 0°C to 70°C –40°C to 85°C (1) PACKAGED DEVICES (1) 128-PIN TQFP PowerPAD™ PACKAGE OPTION TVP5154APNP Tray TVP5154APNPR Tape and reel TVP5154AIPNP Tray TVP5154AIPNPR Tape and reel For the most current package and ordering information, see the Package Option Addendum at the end of this document, or see the TI web site at www.ti.com. Introduction Copyright © 2007–2010, Texas Instruments Incorporated Submit Documentation Feedback Product Folder Link(s): TVP5154A 3 TVP5154A SLES214C – DECEMBER 2007 – REVISED SEPTEMBER 2010 1 2 3 4 .............................................. 1 1.1 Features .............................................. 1 1.2 Description ........................................... 1 1.3 Applications .......................................... 2 1.4 Related Products ..................................... 3 1.5 Trademarks .......................................... 3 1.6 Document Conventions .............................. 3 1.7 Ordering Information ................................. 3 Device Details ............................................ 5 2.1 Functional Block Diagram ............................ 5 2.2 Terminal Diagram .................................... 6 2.3 Terminal Functions ................................... 7 Functional Description ................................. 9 3.1 Analog Front End .................................... 9 3.2 Composite Processing Block Diagram ............... 9 3.3 Adaptive Comb Filtering ............................ 10 3.4 Color Low-Pass Filter ............................... 11 3.5 Luminance Processing ............................. 11 3.6 Chrominance Processing ........................... 11 3.7 Timing Processor ................................... 11 3.8 VBI Data Processor ................................ 12 3.9 VBI FIFO and Ancillary Data in Video Stream ..... 13 3.10 Raw Video Data Output ............................ 14 3.11 Output Formatter ................................... 14 3.12 Synchronization Signals ............................ 14 3.13 Active Video (AVID) Cropping ...................... 15 3.14 Embedded Syncs ................................... 17 www.ti.com Introduction ............................. ...................................... 4.1 I2C Write Operation ................................. 4.2 I2C Read Operation ................................. Clock Circuits .......................................... Genlock Control and RTC ........................... 6.1 TVP5154A Genlock Control Interface .............. 6.2 RTC Mode .......................................... 6.3 Reset and Power Down ............................ 6.4 Reset Sequence .................................... Internal Control Registers ........................... 7.1 Overview ............................................ 7.2 Direct Register Definitions .......................... 7.3 Indirect Register Definitions ........................ Scaler Configuration .................................. 8.1 Overview ............................................ 8.2 Horizontal Scaling .................................. 8.3 Vertical Scaling ..................................... 8.4 Field Interleaving ................................... Electrical Specifications ............................. 9.1 Absolute Maximum Ratings ........................ 9.2 Recommended Operating Conditions .............. 9.3 Reference Clock Specifications .................... 9.4 Electrical Characteristics ........................... 9.5 Timing Requirements ............................... 9.6 I2C Host Port Timing ................................ 9.7 Thermal Specifications ............................. Schematic ............................................... Revision History ....................................... 3.15 4 5 6 7 8 9 10 11 Clock and Data Control I2C Host Interface Contents 18 19 20 20 22 23 23 23 24 25 26 26 29 75 79 79 79 80 81 82 82 82 82 83 84 85 85 86 87 Copyright © 2007–2010, Texas Instruments Incorporated Submit Documentation Feedback Product Folder Link(s): TVP5154A TVP5154A www.ti.com SLES214C – DECEMBER 2007 – REVISED SEPTEMBER 2010 2 Device Details 9−Bit A/D PGA Luminance Processing Scaler Chrominance Processing AIP2A AIP2B M U X Y/C Separation VBI Data Processor (VDP) 9−Bit A/D PGA Luminance Processing Scaler Chrominance Processing AIP3A AIP3B M U X Y/C Separation VBI Data Processor (VDP) 9−Bit A/D PGA Luminance Processing Scaler Chrominance Processing AIP4B M U X 9−Bit A/D PGA SCL SDA XOUT Scaler Chrominance Processing Host Interface Embedded Processor XIN/OSC Luminance Processing Horizontal and Color PLLs CH1_OUT [7:0] YCBCR 8−Bit 4:2:2 CH2_OUT [7:0] YCBCR 8−Bit 4:2:2 CH3_OUT [7:0] YCBCR 8−Bit 4:2:2 CH4_OUT [7:0] YCBCR 8−Bit 4:2:2 FID/GLCO[1−4] Timing Processor AIP4A Y/C Separation VBI Data Processor (VDP) Output Formatter AIP1B M U X Output Formatter AIP1A Y/C Separation VBI Data Processor (VDP) Output Formatter Functional Block Diagram Output Formatter 2.1 VSYNC/PAL[1−4] INTERQ/GPCL/BLK[1−4] HSYNC[1−4] AVID[1−4] CLK[1−4] SCLK[1−4] Figure 2-1. Functional Block Diagram Device Details Copyright © 2007–2010, Texas Instruments Incorporated Submit Documentation Feedback Product Folder Link(s): TVP5154A 5 TVP5154A SLES214C – DECEMBER 2007 – REVISED SEPTEMBER 2010 2.2 www.ti.com Terminal Diagram 128 127 126 125 124 123 122 121 120 119 118 117 116 115 114 113 112 111 110 109 108 107 106 105 104 103 102 101 100 99 98 97 AGND AVDD REFP1 REFM1 XIN/OSC XOUT PDN RESETB SCL SDA I2CA0 I2CA1 DGND DVDD IOVDD IOGND CH1_OUT0 CH1_OUT1 CH1_OUT2 CH1_OUT3 CH1_OUT4 CH1_OUT5 CH1_OUT6 CH1_OUT7 SCLK1 CLK1 INTREQ1/GPCL1/VBLK1 AVID1 HSYNC1 DGND DVDD IOVDD PNP Package (Top View) 96 95 94 93 92 91 90 89 88 87 86 85 84 83 82 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 81 80 79 78 77 76 75 74 73 72 71 70 69 68 67 66 65 IOGND VSYNC1/PALI1 FID1/GLCO1 CH2_OUT0 CH2_OUT1 CH2_OUT2 CH2_OUT3 CH2_OUT4 CH2_OUT5 CH2_OUT6 CH2_OUT7 SCLK2 CLK2 INTREQ2/GPCL2/VBLK2 DGND DVDD IOVDD IOGND AVID2 HSYNC2 VSYNC2/PALI2 FID2/GLCO2 CH3_OUT0 CH3_OUT1 CH3_OUT2 CH3_OUT3 CH3_OUT4 CH3_OUT5 CH3_OUT6 CH3_OUT7 DGND DVDD PLL_VDD PLL_GND AGND TMS FID4/GLCO4 VSYNC4/PALI4 HSYNC4 AVID4 INTREQ4/GPCL4/VBLK4 CLK4 SCLK4 IOGND IOVDD DVDD DGND CH4_OUT7 CH4_OUT6 CH4_OUT5 CH4_OUT4 CH4_OUT3 CH4_OUT2 CH4_OUT1 CH4_OUT0 FID3/GLCO3 VSYNC3/PALI3 HSYNC3 AVID3 INTREQ3/GPCL3/VBLK3 CLK3 SCLK3 IOGND IOVDD 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 AI1GND AIP1A AIP1B PLL_VDD PLL_GND REFM2 REFP2 AVDD AGND AI2GND AIP2A AIP2B PLL_VDD PLL_GND AVDD AGND REFM3 REFP3 AVDD AGND AI3GND AIP3A AIP3B PLL_VDD PLL_GND REFM4 REFP4 AVDD AGND AI4GND AIP4A AIP4B 6 Device Details Copyright © 2007–2010, Texas Instruments Incorporated Submit Documentation Feedback Product Folder Link(s): TVP5154A TVP5154A www.ti.com 2.3 SLES214C – DECEMBER 2007 – REVISED SEPTEMBER 2010 Terminal Functions TERMINAL NAME NO. I/O DESCRIPTION I Analog inputs for Channel 1. Connect to the video analog input via a 0.1-µF capacitor. The maximum input range is 0–0.75 VPP, and may require an attenuator to reduce the input amplitude to the desired level. If not used, connect to AGND via a 0.1-µF capacitor. See the schematic in Section 10. I Analog inputs for Channel 2. Connect to the video analog input via a 0.1-µF capacitor. The maximum input range is 0-0.75 VPP, and may require an attenuator to reduce the input amplitude to the desired level. If not used, connect to AGND via a 0.1-µF capacitor. See the schematic in Section 10. I Analog inputs for Channel 3. Connect to the video analog input via a 0.1-µF capacitor. The maximum input range is 0-0.75 VPP, and may require an attenuator to reduce the input amplitude to the desired level. If not used, connect to AGND via a 0.1-µF capacitor. See the schematic in Section 10. Analog Section AIP1A AIP1B 2 3 AIP2A AIP2B 11 12 AIP3A AIP3B 22 23 AIP4A AIP4B 31 32 I Analog inputs for Channel 4. Connect to the video analog input via a 0.1-µF capacitor. The maximum input range is 0-0.75 VPP, and may require an attenuator to reduce the input amplitude to the desired level. If not used, connect to AGND via a 0.1-µF capacitor. See the schematic in Section 10. AVDD 8, 15, 19, 28, 127 P Analog power supply. Connect to 1.8-V analog supply. AGND 9, 16, 20, 29, 35, 128 G Analog power supply return. Connect to analog ground. AIxGND 1, 10, 21, 30 G Analog input signal return. Connect to analog ground. PLL_GND 5, 14, 25, 34 G PLL power supply return. Connect to analog ground. PLL_VDD 4, 13, 24, 33 P PLL power supply. Connect to 1.8-V analog supply. REFMx 6, 17, 26, 125 I Reference supply decoupling . Connect to analog ground through a 1-µF capacitor. Connect to REFPx through a 1-µF capacitor. REFPx 7, 18, 27, 126 I Reference supply decoupling . Connect to analog ground through a 1-µF capacitor. Connect to REFMx through a 1-µF capacitor. DGND 47, 66, 82, 99, 116 G Digital power supply return. Connect to digital ground DVDD 46, 65, 81, 98, 115 P Digital power supply. Connect to 1.8-V digital supply. IOGND 44, 63, 79, 96, 113 G I/O power supply return. Connect to digital ground. IOVDD 45, 64, 80, 97, 114 P I/O power supply. Connect to 3.3-V digital supply Digital Section FID1/GLCO1 FID2/GLCO2 FID3/GLCO3 FID4/GLCO4 94 75 56 37 O 1. FID: Odd/even field indicator or vertical lock indicator. For the odd/even indicator, a 1 indicates the odd field. 2. GLCO: This serial output carries color PLL information. A slave device can decode the information to allow chroma frequency control from the TVP5154A decoder. Data is transmitted at the CLK rate in Genlock mode. AVID1 AVID2 AVID3 AVID4 101 78 59 40 O Active video indicator. This signal is high during the horizontal active time of the video output. INTREQ1/GPCL1/VBLK1 INTREQ2/GPCL2/VBLK2 INTREQ3/GPCL3/VBLK3 INTREQ4/GPCL4/VBLK4 102 83 60 41 1. 2. I/O 3. Interrupt request : Open drain when active low. GPCL: General-purpose output. In this mode, the state of GPCL is directly programmed via I2C. VBLK: Vertical blank output. In this mode, the GPCL terminal is used to indicate the VBI of the output video. The beginning and end times of this signal are programmable via I2C. Device Details Copyright © 2007–2010, Texas Instruments Incorporated Submit Documentation Feedback Product Folder Link(s): TVP5154A 7 TVP5154A SLES214C – DECEMBER 2007 – REVISED SEPTEMBER 2010 TERMINAL NAME NO. I/O www.ti.com DESCRIPTION HSYNC1 HSYNC2 HSYNC3 HSYNC4 100 77 58 39 O Horizontal synchronization VSYNC1/PALI1 VSYNC2/PALI2 VSYNC3/PALI3 VSYNC4/PALI4 95 76 57 38 O 1. 2. PDN 122 I Power down (active low). A 0 on this pin puts the decoder in standby mode. PDN preserves the value of the registers. RESETB 121 I Active-low reset. RESETB can be used only when PDN = 1. When RESETB is pulled low, it resets all the registers and restarts the internal microprocessor. SCL 120 I/O I2C serial clock (open drain) SDA 119 I/O I2C serial data (open drain) I2CA0 118 I During power-on reset, this pin is sampled along with pin 117 (I2CA1) to determine the I2C address the device is configured to. A 10-kΩ resistor should pull this either high (to IOVDD) or low to select different I2C device addresses. I2CA1 117 I During power-on reset, this pin is sampled along with pin 118 (I2CA0) to determine the I2C address the device is configured to. A 10-kΩ resistor should pull this either high (to IOVDD) or low to select different I2C device addresses. CLK1 CLK2 CLK3 CLK4 103 84 61 42 O Unscaled system data clock at either 27 MHz or 54 MHz SCLK1 SCLK2 SCLK3 SCLK4 104 85 62 43 O Scaled system data clock at 27 MHz. This signal can be used to qualify scaled/unscaled data when the unscaled system data clock is set to 54 MHz. XIN/OSC XOUT 124 123 I O External clock reference. The user may connect XIN to an oscillator or to one terminal of a crystal oscillator. The user may connect XOUT to the other terminal of the crystal oscillator or not connect XOUT at all. One single 14.31818-MHz crystal or oscillator is needed for ITU-R BT.601 sampling, for all supported standards. CH1_OUT[7:0] 105–112 O Decoded ITU-R BT.656 output/YCbCr 4:2:2 output with discrete sync for channel 1 CH2_OUT[7:0] 86–93 O Decoded ITU-R BT.656 output/YCbCr 4:2:2 output with discrete sync for channel 2 CH3_OUT[7:0] 67–74 O Decoded ITU-R BT.656 output/YCbCr 4:2:2 output with discrete sync for channel 3 CH4_OUT[7:0] 48–55 O Decoded ITU-R BT.656 output/YCbCr 4:2:2 output with discrete sync for channel 4 36 I Test-mode select. This pin should be connected to digital ground for correct device operation. TMS 8 VSYNC: Vertical synchronization PALI: PAL line indicator or horizontal lock indicator. For the PAL line indicator, a 1 indicates a noninverted line, and a 0 indicates an inverted line. Device Details Copyright © 2007–2010, Texas Instruments Incorporated Submit Documentation Feedback Product Folder Link(s): TVP5154A TVP5154A www.ti.com SLES214C – DECEMBER 2007 – REVISED SEPTEMBER 2010 3 Functional Description 3.1 Analog Front End Each channel of the TVP5154A decoder has an analog input channel that accepts two video inputs, which should be ac coupled through 0.1-µF capacitors. The decoder supports a maximum input voltage range of 0.75 V; therefore, an attenuation of one-half is needed for standard input signals with a peak-to-peak variation of 1.5 V. The maximum parallel termination before the input to the device is 75 Ω. See the schematic in Section 10 for recommended configuration. The two analog input ports can be connected as follows: • Two selectable composite video inputs or • One S-video input An internal clamping circuit restores the ac-coupled video signal to a fixed dc level. The programmable gain amplifier (PGA) and the automatic gain control (AGC) circuit work together to ensure that the input signal is amplified or attenuated correctly, ensuring the proper input range for the ADC. When switching CVBS inputs from one input to the other, the AGC settings are internally stored and the previous settings for the new input are restored. This eliminates flashes and dark frames associated with switching between inputs that have different signal amplitudes. The ADC has nine bits of resolution and runs at a maximum speed of 27 MHz. The clock input for the ADC comes from the PLL. 3.2 Composite Processing Block Diagram The composite processing block processes NTSC/PAL/SECAM signals into the YCbCr color space. Figure 2-1 shows the basic architecture of this processing block. Figure 2-1 shows the luminance/chrominance (Y/C) separation process in the TVP5154A decoders. The composite video is multiplied by sub-carrier signals in the quadrature modulator to generate the color difference signals Cb and Cr. Cb and Cr are then low pass (LP) filtered to achieve the desired bandwidth and to reduce crosstalk. An adaptive 4-line comb filter separates CbCr from Y. Chroma is remodulated through another quadrature modulator and subtracted from the line-delayed composite video to generate luma. Contrast, brightness, hue, saturation, and sharpness (using the peaking filter) are programmable via I2C. The Y/C separation is bypassed for S-video input. For S-video, the remodulation path is disabled. Functional Description Copyright © 2007–2010, Texas Instruments Incorporated Submit Documentation Feedback Product Folder Link(s): TVP5154A 9 TVP5154A SLES214C – DECEMBER 2007 – REVISED SEPTEMBER 2010 3.3 www.ti.com Adaptive Comb Filtering The 4-line comb filter can be selectively bypassed in the luma or chroma path. If the comb filter is bypassed in the luma path, then chroma trap filters are used which are shown in Figure 3-1 and Figure 3-2. TI's patented adaptive 4-line comb filter algorithm reduces artifacts, such as hanging dots at color boundaries, and detects and properly handles false colors in high-frequency luminance images, such as a multiburst pattern or circle pattern. Figure 3-1. Chroma Trap Filter Frequency Response, NTSC ITU-R BT.601 Sampling Figure 3-2. Chroma Trap Filter Frequency Response, PAL ITU-R BT.601 Sampling 10 Functional Description Copyright © 2007–2010, Texas Instruments Incorporated Submit Documentation Feedback Product Folder Link(s): TVP5154A TVP5154A www.ti.com 3.4 SLES214C – DECEMBER 2007 – REVISED SEPTEMBER 2010 Color Low-Pass Filter In some applications, it is desirable to limit the Cb/Cr bandwidth to avoid crosstalk. This is especially true in the case of video signals that have asymmetrical Cb/Cr sidebands. The provided color LP filters limit the bandwidth of the Cb/Cr signals. Color LP filters are needed when the comb filtering turns off, due to extreme color transitions in the input image. See Chrominance Control #2 Register (Section 7.2.27), for the response of these filters. The filters have three options that allow three different frequency responses based on the color frequency characteristics of the input video as shown in Figure 3-3. Figure 3-3. Color Low-Pass Filter with Filter Characteristics, NTSC/PAL ITU-R BT.601 Sampling 3.5 Luminance Processing The luma component is derived from the composite signal by subtracting the remodulated chroma information. A line delay exists in this path to compensate for the line delay in the adaptive comb filter in the color processing chain. The luma information is then fed into the peaking circuit, which enhances the high-frequency components of the signal, thus, improving sharpness. 3.6 Chrominance Processing For NTSC/PAL formats, the color processing begins with a quadrature demodulator. The Cb/Cr signals then pass through the gain control stage for chroma saturation adjustment. An adaptive comb filter is applied to the demodulated signals to separate chrominance and eliminate cross-chrominance artifacts. An automatic color-killer circuit is also included in this block. The color killer suppresses the chrominance processing when the burst amplitude falls below a programmable threshold (see I2C subaddress 06h, Section 7.2.7). The SECAM standard is similar to PAL except for the modulation of color, which is FM instead of QAM. 3.7 Timing Processor The timing processor is a combination of hardware and software running in the internal microprocessor that serves to control horizontal lock to the input sync pulse edge, AGC and offset adjustment in the analog front end, and vertical sync detection. Functional Description Copyright © 2007–2010, Texas Instruments Incorporated Submit Documentation Feedback Product Folder Link(s): TVP5154A 11 TVP5154A SLES214C – DECEMBER 2007 – REVISED SEPTEMBER 2010 3.8 www.ti.com VBI Data Processor The TVP5154A VBI data processor (VDP) slices various data services, such as teletext (WST, NABTS), closed caption (CC), wide screen signaling (WSS), etc. These services are acquired by programming the VDP to enable standards in the VBI. The results are stored in a FIFO and/or registers. The teletext results are stored in a FIFO only. Table 3-1 lists a summary of the types of VBI data supported according to the video standard. It supports ITU-R BT.601 sampling for each. Table 3-1. Data Types Supported by the VDP LINE MODE REGISTER (D0h–FCh) BITS [3:0] NAME DESCRIPTION 0000b WST SECAM Teletext, SECAM 0001b WST PAL B Teletext, PAL, System B 0010b WST PAL C Teletext, PAL, System C 0011b WST, NTSC B Teletext, NTSC, System B 0100b NABTS, NTSC C Teletext, NTSC, System C 0101b NABTS, NTSC D Teletext, NTSC, System D (Japan) 0110b CC, PAL Closed caption PAL 0111b CC, NTSC Closed caption NTSC 1000b WSS/CGMS-A, PAL Wide-screen signaling/Copy Generation Management System-Analog, PAL 1001b WSS/CGMS-A, NTSC Wide-screen signaling/Copy Generation Management System-Analog, NTSC 1010b VITC, PAL Vertical interval timecode, PAL 1011b VITC, NTSC Vertical interval timecode, NTSC 1100b VPS, PAL Video program system, PAL 1101b Gemstar 2x Custom 1 Electronic program guide 1110b Reserved Reserved 1111b Active Video Active video/full field At power up, the host interface is required to program the VDP-configuration RAM (VDP-CRAM) contents with the lookup table (see Section 7.2.69). This is done through port address C3h. Each read from or write to this address auto increments an internal counter to the next RAM location. To access the VDP-CRAM, the line mode registers (D0h–FCh) must be programmed with FFh to avoid a conflict with the internal microprocessor and the VDP in both writing and reading. Full field mode must also be disabled. Available VBI lines are from line 6 to line 27 of both field 1 and field 2. Each line can be any VBI mode. Output data is available either through the VBI-FIFO (B0h) or through dedicated registers at 90h–AFh, both of which are available through the I2C port. 12 Functional Description Copyright © 2007–2010, Texas Instruments Incorporated Submit Documentation Feedback Product Folder Link(s): TVP5154A TVP5154A www.ti.com 3.9 SLES214C – DECEMBER 2007 – REVISED SEPTEMBER 2010 VBI FIFO and Ancillary Data in Video Stream Sliced VBI data can be output as ancillary data in the video stream in the ITU-R BT.656 mode. VBI data is output during the horizontal blanking period following the line from which the data was retrieved. Table 3-2 shows the header format and sequence of the ancillary data inserted into the video stream. This format is also used to store any VBI data into the FIFO. The size of FIFO is 512 bytes. Therefore, the FIFO can store up to 11 lines of teletext data with the NTSC NABTS standard. Table 3-2. Ancillary Data Format and Sequence BYTE NO. D7 (MSB) D6 D5 D4 D3 D2 D1 D0 (LSB) 0 0 0 0 0 0 0 0 0 1 1 1 1 1 1 1 1 1 2 1 1 1 1 1 1 1 1 3 NEP EP 0 1 0 DID2 DID1 DID0 4 NEP EP F5 F4 F3 F2 F1 F0 Secondary data ID (SDID) 5 NEP EP N5 N4 N3 N2 N1 N0 Number of 32 bit data (NN) 6 DESCRIPTION Ancillary data preamble Data ID (DID) Video line # [7:0] 7 0 0 0 Data error Internal data ID0 (IDID0) Match #1 Match #2 Video line # [9:8] Internal data ID1 (IDID1) 8 1. Data Data byte 9 2. Data Data byte 10 3. Data Data byte 11 4. Data Data byte ⋮ ⋮ ⋮ —1. Data Data byte m. Data NEP EP 0 0 4(N+2)-1 0 EP: Even parity for D0–D5 NEP: Negated even parity DID: 91h: Sliced data of VBI lines of first field Nth word Data byte CS[5:0] 0 1st word 0 Check sum 0 0 0 Fill byte 53h: Sliced data of line 24 to end of first field 55h: Sliced data of VBI lines of second field 97h: Sliced data of line 24 to end of second field SDID: This field holds the data format taken from the line mode register of the corresponding line. NN: Number of Dwords beginning with byte 8 through 4(N+2). This value is the number of Dwords where each Dword is 4 bytes. IDID0: Transaction video line number [7:0] IDID1: Bit 0/1 = Transaction video line number [9:8] Bit 2 = Match 2 flag Bit 3 = Match 1 flag Bit 4 = 1 if an error was detected in the EDC block. 0 if not. CS: Sum of D0–D7 of DID through last data byte Fill byte: Fill bytes make a multiple of four bytes from byte 0 to last fill byte. For teletext modes, byte 8 is the sync pattern byte. Byte 9 is 1. Data (the first data byte). Functional Description Copyright © 2007–2010, Texas Instruments Incorporated Submit Documentation Feedback Product Folder Link(s): TVP5154A 13 TVP5154A SLES214C – DECEMBER 2007 – REVISED SEPTEMBER 2010 www.ti.com 3.10 Raw Video Data Output The TVP5154A decoder can output raw A/D video data at 2× sampling rate for external VBI slicing. This is transmitted as an ancillary data block during the active horizontal portion of the line and during vertical blanking. 3.11 Output Formatter The output formatter is responsible for generating the output digital video stream. The YCbCr digital output can be programmed as 8-bit 4:2:2 or 8-bit ITU-R BT.656 parallel interface standard. Depending on which output mode is selected, the output for each channel can be unscaled data, scaled data, or both scaled and unscaled data interleaved in various ways. Table 3-3. Summary of Line Frequencies, Data Rates and Pixel Counts for Different Standards STANDARDS (ITU-R BT.601) PIXELS PER LINE ACTIVE PIXELS PER LINE LINES PER FRAME PIXEL FREQUENCY (MHz) COLOR SUB-CARRIER FREQUENCY (MHz) HORIZONTAL LINE RATE (kHz) NTSC-J, M 858 720 525 13.5 3.579545 15.73426 NTSC-4.43 858 720 525 13.5 4.43361875 15.73426 PAL-M 858 720 525 13.5 3.57561149 15.73426 PAL-B, D, G, H, I 864 720 625 13.5 4.43361875 15.625 PAL-N 864 720 625 13.5 4.43361875 15.625 PAL-Nc 864 720 625 13.5 3.58205625 15.625 SECAM 864 720 625 13.5 4.40625/4.25 15.625 3.12 Synchronization Signals External (discrete) syncs are provided via the following signals: • VSYNC (vertical sync) • FID/VLK (field indicator or vertical lock indicator) • GPCL/VBLK (general-purpose I/O or vertical blanking indicator) • PALI/HLK (PAL switch indicator or horizontal lock indicator) • HSYNC (horizontal sync) • AVID (active video indicator) VSYNC, FID, PALI, and VBLK are software set and programmable to the CLK pixel count. This allows any possible alignment to the internal pixel count and line count. The default settings for a 525-/625-line video output are shown in Figure 3-4. 14 Functional Description Copyright © 2007–2010, Texas Instruments Incorporated Submit Documentation Feedback Product Folder Link(s): TVP5154A TVP5154A www.ti.com SLES214C – DECEMBER 2007 – REVISED SEPTEMBER 2010 525 LINE 525 1 2 3 4 5 6 7 8 9 10 11 20 21 22 Composite Video VSYNC FID GPCL/VBLK ↔ VBLK Stop ↔ VBLK Start 262 263 264 265 266 267 268 269 270 271 272 273 282 283 284 Composite Video VSYNC FID GPCL/VBLK ↔ VBLK Stop ↔ VBLK Start 625 LINE 310 311 312 313 314 315 316 317 318 319 320 333 334 335 336 Composite Video VSYNC FID GPCL/VBLK ↔ VBLK Stop ↔ VBLK Start 622 623 624 625 1 2 3 4 5 6 7 20 21 22 23 Composite Video VSYNC FID GPCL/VBLK ↔ VBLK Start ↔ VBLK Stop Line numbering conforms to ITU-R BT.470. Figure 3-4. 8-Bit 4:2:2, Timing With 2× Pixel Clock (CLK) Reference HSYN HSYN START AVID AV ID STOP AV ID STA RT NOTE: AVID rising edge occurs four CLK cycles early when in ITU-R BT.656 output mode. Figure 3-5. Horizontal Synchronization Signals 3.13 Active Video (AVID) Cropping AVID cropping provides a means to decrease the amount of video data output. This is accomplished by horizontally blanking a number of AVID pulses and by vertically blanking a number of lines per frame. The horizontal AVID cropping is controlled using registers 11h and 12h for start pixels MSB and LSB, respectively. Functional Description Copyright © 2007–2010, Texas Instruments Incorporated Submit Documentation Feedback Product Folder Link(s): TVP5154A 15 TVP5154A SLES214C – DECEMBER 2007 – REVISED SEPTEMBER 2010 www.ti.com Registers 13h and 14h provide access to stop pixels MSB and LSB, respectively. The vertical AVID cropping is controlled using the vertical blanking (VBLK) start and stop registers at addresses 18h and 19h. Figure 3-6 shows an AVID application. AVID cropping can be independently controlled for scaled (registers 25h, 26h, 29h, and 2Ah) and unscaled (registers 11h thru 14h) data streams. AVID start and stop must be changed in multiples of two pixels to ensure correct UV alignment. Additionally, AVID start and stop can be configured to include the SAV- and EAV-embedded sync signals or to exclude them, and to either include or exclude ITU656 ancillary data. NOTE The above settings alter AVID output timing, but the video output data is not forced to black level outside of the AVID interval. VBLK Stop Active Video Area AVID Cropped Area VSYNC VBLK Start AVID Start AVID Stop HSYNC Figure 3-6. AVID Application 16 Functional Description Copyright © 2007–2010, Texas Instruments Incorporated Submit Documentation Feedback Product Folder Link(s): TVP5154A TVP5154A www.ti.com SLES214C – DECEMBER 2007 – REVISED SEPTEMBER 2010 3.14 Embedded Syncs Standards with embedded syncs insert SAV and EAV codes into the data stream at the beginning and end of horizontal blanking. These codes contain the V and F bits that also define vertical timing. F and V change on EAV. Table 3-4 gives the format of the SAV and EAV codes. H equals 1 always indicates EAV. H equals 0 always indicates SAV. The alignment of V and F to the line and field counter varies depending on the standard. See ITU-R BT.656 for more information on embedded syncs. The P bits are protection bits: P3 = V x or H P2 = F x or H P1 = F x or V P0 = F x or V x or H Table 3-4. EAV and SAV Sequence 8-BIT DATA D7 (MSB) D6 D5 D4 D3 D2 D1 D0 Preamble 1 1 1 1 1 1 1 1 Preamble 0 0 0 0 0 0 0 0 Preamble 0 0 0 0 0 0 0 0 Status word 1 F V H P3 P2 P1 P0 The status word may be modified to pass information about whether the current data corresponds to scaled or unscaled data. See register 1Fh for more information. Functional Description Copyright © 2007–2010, Texas Instruments Incorporated Submit Documentation Feedback Product Folder Link(s): TVP5154A 17 TVP5154A SLES214C – DECEMBER 2007 – REVISED SEPTEMBER 2010 www.ti.com 3.15 Clock and Data Control Figure 3-7 shows a logical schematic of the data and clock control signals. Blank Blank =01 Delay Delay =00 Scaler Scaler =11 Data Decoder Decoder Field mode(0) Field mode(1) Field mode(2) Field mode(3) Field mode(4) Field mode(5) Field mode(6) Field mode(7) Field mode(8) Field mode(9) Field mode(10) Field mode(11) Field mode(12) Field mode(13) Field mode(14) Field mode(15) =4 01 =1 00 =0 /2 = 27 MHz =2/3 Mode SCLK SCLK OE SCLK edge !=3 CLK 54 54MHz MHz =3 CLK OE Mode CLK edge Figure 3-7. Clock and Data Control 18 Functional Description Copyright © 2007–2010, Texas Instruments Incorporated Submit Documentation Feedback Product Folder Link(s): TVP5154A TVP5154A www.ti.com SLES214C – DECEMBER 2007 – REVISED SEPTEMBER 2010 4 I2C Host Interface The I2C standard consists of two signals, serial input/output data line (SDA) and input/output clock line (SCL), which carry information between the devices connected to the bus. The input pins I2CA0 and I2CA1 are used to select the slave address to which the device responds. Although the I2C system can be multimastered, the TVP5154A decoder functions as a slave device only. Both SDA and SCL must be connected to IOVDD via pullup resistors. When the bus is free, both lines are high. The slave address select terminals (I2CA0 and I2CA1) enable the use of four TVP5154A decoders on the same I2C bus. At the trailing edge of reset, the status of the I2CA0 and I2CA1 lines are sampled to determine the device address used. Table 4-1 summarizes the terminal functions of the I2C-mode host interface. Table 4-2 shows the device address selection options. Table 4-1. I2C Terminal Description SIGNAL TYPE DESCRIPTION I2CA0 I Slave address selection I2CA1 I Slave address selection SCL I/O (open drain) Input/output clock line SDA I/O (open drain) Input/output data line Table 4-2. I2C Host Interface Device Addresses A6 A5 A4 A3 A2 A1 (I2CA1) A0 (I2CA0) R/W HEX 1 0 1 1 1 0 0 1/0 B9/B8 1 0 1 1 1 0 1 1/0 BB/BA 1 0 1 1 1 1 0 1/0 BD/BC 1 0 1 1 1 1 1 1/0 BF/BE Data transfer rate on the bus is up to 400 kbit/s. The number of interfaces connected to the bus is dependent on the bus capacitance limit of 400 pF. The data on the SDA line must be stable during the high period of the SCL, except for start and stop conditions. The high or low state of the data line can only change with the clock signal on the SCL line being low. A high-to-low transition on the SDA line while the SCL is high indicates an I2C start condition. A low-to-high transition on the SDA line while the SCL is high indicates an I2C stop condition. Every byte placed on the SDA must be eight bits long. The number of bytes that can be transferred is unrestricted. Each byte must be followed by an acknowledge bit. The acknowledge-related clock pulse is generated by the I2C master. To simplify programming of each of the four decoder channels, a single I2C write transaction can be transmitted to any one or more of the four cores in parallel. This reduces the time required to download firmware or to configure the device when all channels are to be configured in the same manner. It also enables the addresses for all registers to be common across all decoders. I2C sub-address 0xFE contains four bits, with each bit corresponding to one of the decoder cores. If this bit is set, I2C write transactions are sent to the corresponding decoder core. If the bit is 0, the corresponding decoder does not receive the I2C write transactions. I2C sub-address 0xFF contains four bits, with each bit corresponding to one of the decoder cores. If this bit is set, I2C read transactions are sent to the corresponding decoder core. Note, only one of the bits in this register should be set at a given time, ensuring that only one decoder core is accessed at a time for read operations. If more than one bit is set, the lowest set bit number corresponds to the core that responds to the read transaction. Note that, when register 0xFE is written to with any value, register 0xFF is set to 0x00. Likewise, when register 0xFF is written to with any value, register 0xFE is set to 0x00. I2C Host Interface Copyright © 2007–2010, Texas Instruments Incorporated Submit Documentation Feedback Product Folder Link(s): TVP5154A 19 TVP5154A SLES214C – DECEMBER 2007 – REVISED SEPTEMBER 2010 4.1 www.ti.com I2C Write Operation Data transfers occur utilizing the following illustrated formats. An I2C master initiates a write operation to the TVP5154A decoder by generating a start condition (S) followed by the TVP5154A I2C address (as shown below), in MSB first bit order, followed by a 0 to indicate a write cycle. After receiving an acknowledge from the TVP5154A decoder, the master presents the sub-address of the register, or the first of a block of registers it wants to write, followed by one or more bytes of data, MSB first. The TVP5154A decoder acknowledges each byte after completion of each transfer. The I2C master terminates the write operation by generating a stop condition (P). Step 1 I2C start (master) 0 S Step 2 I2C general address (master) 7 1 Step 3 I2C acknowledge (slave) 9 A Step 4 I2C write register address (master) Step 5 I2C acknowledge (slave) Step 6 I2C write data (master) 7 addr 7 Data 9 A Step 8 I2C stop (master) 0 P 4.2 5 1 4 1 3 1 2 0 1 X 0 0 6 addr 5 addr 4 addr 3 addr 2 addr 1 addr 0 addr 6 Data 5 Data 4 Data 3 Data 2 Data 1 Data 0 Data 9 A Step 7 (1) I2C acknowledge (slave) (1) 6 0 Repeat steps 6 and 7 until all data have been written. I2C Read Operation The read operation consists of two phases. The first phase is the address phase. In this phase, an I2C master initiates a write operation to the TVP5154A decoder by generating a start condition (S) followed by the TVP5154A I2C address, in MSB first bit order, followed by a 0 to indicate a write cycle. After receiving acknowledges from the TVP5154A decoder, the master presents the sub-address of the register or the first of a block of registers it wants to read. After the cycle is acknowledged, the master terminates the cycle immediately by generating a stop condition (P). The second phase is the data phase. In this phase, an I2C master initiates a read operation to the TVP5154A decoder by generating a start condition followed by the TVP5154A I2C address (as shown below for a read operation), in MSB first bit order, followed by a 1 to indicate a read cycle. After an acknowledge from the TVP5154A decoder, the I2C master receives one or more bytes of data from the TVP5154A decoder. The I2C master acknowledges the transfer at the end of each byte. After the last data byte desired has been transferred from the TVP5154A decoder to the master, the master generates a not acknowledge followed by a stop. 20 I2C Host Interface Copyright © 2007–2010, Texas Instruments Incorporated Submit Documentation Feedback Product Folder Link(s): TVP5154A TVP5154A www.ti.com SLES214C – DECEMBER 2007 – REVISED SEPTEMBER 2010 Read Phase 1 Step 1 I2C start (master) 0 S Step 2 I2C general address (master) 7 1 Step 3 I2C acknowledge (slave) 9 A Step 4 I2C read register address (master) 7 addr Step 5 I2C acknowledge (slave) 9 A Step 6 I2C stop (master) 0 P 6 0 5 1 4 1 3 1 2 0 1 X 0 0 6 addr 5 addr 4 addr 3 addr 2 addr 1 addr 0 addr 6 0 5 1 4 1 3 1 2 0 1 X 0 1 6 Data 5 Data 4 Data 3 Data 2 Data 1 Data 0 Data Read Phase 2 Step 7 I2C start (master) 0 S Step 8 I2C general address (master) 7 1 Step 9 I2C acknowledge (slave) 9 A Step 10 I2C read data (slave) 7 Data Step 11 (1) I2C not acknowledge (master) 9 A Step 12 I2C stop (master) 0 P (1) Repeat steps 10 and 11 for all bytes read. Master does not acknowledge the last read data received. 4.2.1 I2C Timing Requirements The TVP5154A decoder requires delays in the I2C accesses to accommodate its internal processor's timing. In accordance with I2C specifications, the TVP5154A decoder holds the I2C clock line (SCL) low to indicate the wait period to the I2C master. If the I2C master is not designed to check for the I2C clock line held-low condition, the maximum delays must always be inserted where required. These delays are of variable length; maximum delays are indicated in the following diagram: Table 4-3. I2C Timing Start (1) Slave address (B8h) Ack Subaddress Ack Data (XXh) Ack Wait 128 µs (1) Stop If the SCL pin is not monitored by the master to enable pausing, a delay of 128 µs should be inserted between transactions for registers 00h through 8Fh. Clock Circuits Copyright © 2007–2010, Texas Instruments Incorporated Submit Documentation Feedback Product Folder Link(s): TVP5154A 21 TVP5154A SLES214C – DECEMBER 2007 – REVISED SEPTEMBER 2010 www.ti.com 5 Clock Circuits An internal line-locked PLL generates the system and pixel clocks. A 14.31818-MHz clock is required to drive the PLL. This may be input to the TVP5154A decoder on terminal 124 (XIN), or a crystal of 14.31818-MHz fundamental resonant frequency may be connected across terminals 123 and 124 (XIN and XOUT). Figure 5-1 shows the reference clock configurations. For the example crystal circuit shown (a parallel-resonant crystal with 14.31818-MHz fundamental frequency), the external capacitors must have the following relationship: CL1 = CL2 = 2CL – CSTRAY where CSTRAY is the terminal capacitance with respect to ground and CL is the crystal load capacitance specified by the crystal manufacturer. Figure 5-1 shows the reference clock configurations. TVP5154A XIN/OSC TVP5154A 124 14.31818-MHz 1.8-V Clock XIN/OSC 124 C L1 R XOUT 123 NC XOUT 123 14.31818-MHz Crystal C L2 NOTE: The resistor (R) in parallel with the crystal is recommended to support a wide range of crystal types. A 100-kΩ resistor may be used for most crystal types. Figure 5-1. Clock and Crystal Connectivity 22 Clock Circuits Copyright © 2007–2010, Texas Instruments Incorporated Submit Documentation Feedback Product Folder Link(s): TVP5154A TVP5154A www.ti.com SLES214C – DECEMBER 2007 – REVISED SEPTEMBER 2010 6 Genlock Control and RTC A Genlock control (GLCO) function is provided to support a standard video encoder to synchronize its internal color oscillator for properly reproduced color with unstable timebase sources like VCRs. The frequency control word of the internal color subcarrier digital control oscillator (DTO) and the subcarrier phase reset bit are transmitted via the GLCO terminal. The frequency control word is a 23-bit binary number. The frequency of the DTO can be calculated from the following equation: F F dto + ctrl F clk 223 (1) where Fdto is the frequency of the DTO, Fctrl is the 23–bit DTO frequency control, and Fclk is the frequency of the CLK. 6.1 TVP5154A Genlock Control Interface A write of 1 to bit 4 of the chrominance control register at I2C subaddress 1Ah causes the subcarrier DTO phase reset bit to be sent on the next scan line on GLCO. The active-low reset bit occurs seven CLKs after the transmission of the last bit of DCO frequency control. Upon the transmission of the reset bit, the phase of the TVP5154A internal subcarrier DCO is reset to zero. A Genlock slave device can be connected to the GLCO terminal and uses the information on GLCO to synchronize its internal color phase DCO to achieve clean line and color lock. 6.2 RTC Mode Figure 6-1 shows the timing diagram of the RTC mode. Clock rate for the RTC mode is four times slower than the GLCO clock rate. For PLL frequency control, the upper 22 bits are used. Each frequency control bit is two clock cycles long. The active-low reset bit occurs six CLKs after the transmission of the last bit of PLL frequency control. Genlock Control and RTC Copyright © 2007–2010, Texas Instruments Incorporated Submit Documentation Feedback Product Folder Link(s): TVP5154A 23 TVP5154A SLES214C – DECEMBER 2007 – REVISED SEPTEMBER 2010 www.ti.com CLK GLCO 22 MSB LSB 21 0 >128 CLK 23 CLK 23-Bit Frequency Control 7 CLK 1 CLK 1 CLK Start Bit DCO Reset Bit GLCO Timing L S B M S B RTC 0 21 128 CLK 16 CLK 44 CLK 1 CLK 22-Bit Fsc Frequency Control 2 CLK PAL Switch 2 CLK Start Bit 3 CLK 1 CLK Reset Bit Figure 6-1. RTC Timing 6.3 Reset and Power Down The RESETB and PDN terminals work together to put the TVP5154A decoder into one of the two modes. Table 6-1 shows the configuration. After power-up, the device is in an unknown state with its outputs undefined, until it receives a RESETB signal as depicted in Figure 6-2. After RESETB is released, the data (CHn_OUT[7:0]), sync (HSYNCn, VSYNCn/PALIn), and clock (CLKn, SCLKn) outputs are Hi-Z until the chip is initialized and the outputs are activated. NOTE I2C SCL and SDA signals must not change state until the TVP5154A reset sequence has been completed. 24 Genlock Control and RTC Copyright © 2007–2010, Texas Instruments Incorporated Submit Documentation Feedback Product Folder Link(s): TVP5154A TVP5154A www.ti.com SLES214C – DECEMBER 2007 – REVISED SEPTEMBER 2010 Table 6-1. Reset and Power-Down Modes PDN RESETB 0 0 Reserved (unknown state) CONFIGURATION 0 1 Powers down the decoder 1 0 Resets the decoder 1 1 Normal operation PLL_AVDD DVDD IO_DVDD t1 Normal Operation RESETB Reset t2 PDN t3 SDA Data SCL Figure 6-2. Power-On Reset Timing Table 6-2. Power-On Reset Timing NO. PARAMETER MIN MAX Delay time between power supplies active and reset t2 RESETB pulse duration 500 ns t3 Delay time between end of reset to I2C active 200 µs 6.4 20 UNIT t1 ms Reset Sequence Table 6-3 shows the reset sequence of the TVP5154A pins status during reset time and immediately after reset time. Table 6-3. Reset Sequence DURING RESETB IMMEDIATELY AFTER RESETB 3-state 3-state AIP1A, AIP1B, AIP2A, AIP2B, AIP3A, AIP3B, AIP4A, AIP4B, RESETB, PDN, SDA, SCL, I2CA0, I2CA1, XIN/OSC, TMS Input Input FID1/GLCO1, FID2/GLCO2, FID3/GLCO3, FID4/GLCO4, AVID1, AVID2, AVID3, AVID4, CLK1, CLK2, CLK3, CLK4, SCLK1, SCLK2, SCLK3, SCLK4, XOUT Output Output PIN DESCRIPTION INTREQ1/GPCL1/VBLK1, INTREQ2/GPCL2/VBLK2, INTREQ3/GPCL3/VBLK3, INTREQ4/GPCL4/VBLK4, HSYNC1, HSYNC2, HSYNC3, HSYNC4, VSYNC1/PALI1, VSYNC2/PALI2, VSYNC3/PALI3, VSYNC4/PALI4, CH1_OUT[7:0], CH2_OUT[7:0], CH3_OUT[7:0], CH4_OUT[7:0], Genlock Control and RTC Copyright © 2007–2010, Texas Instruments Incorporated Submit Documentation Feedback Product Folder Link(s): TVP5154A 25 TVP5154A SLES214C – DECEMBER 2007 – REVISED SEPTEMBER 2010 www.ti.com 7 Internal Control Registers 7.1 Overview The TVP5154A decoder is initialized and controlled by sets of internal registers that set all device operating parameters. Communication between the external controller and the TVP5154A decoder is through the I2C. Two sets of registers exist, direct and indirect. Table 7-1 shows the summary of the direct registers. Reserved registers must not be written. Reserved bits in the defined registers must be written with zeros, unless otherwise noted. The detailed programming information of each register is described in the following sections. I2C register FEh controls which of the four decoders receives I2C commands. I2C register FFh controls which decoder core responds to I2C reads. Note, for a read operation, it is necessary to perform a write first, to set the desired sub-address for reading. After power up and the hardware reset, each decoder must be started by writing 00h to register 7Fh for all four decoders. Table 7-1. Direct Register Summary ADDRESS DEFAULT R/W (1) Video input source selection #1 00h 00h R/W Analog channel controls 01h 15h R/W Operation mode controls 02h 00h R/W Miscellaneous controls 03h 01h R/W Autoswitch mask 04h DCh R/W Clock control 05h 08h R/W Color killer threshold control 06h 10h R/W Luminance processing control #1 07h 60h R/W Luminance processing control #2 08h 00h R/W Brightness control 09h 80h R/W Color saturation control 0Ah 80h R/W Hue control 0Bh 00h R/W Contrast control 0Ch 80h R/W Outputs and data rates select 0Dh 47h R/W Luminance processing control #3 0Eh 00h R/W Configuration shared pins 0Fh 08h R/W Reserved 10h Active video cropping start MSB for unscaled data 11h 00h R/W Active video cropping start LSB for unscaled data 12h 00h R/W Active video cropping stop MSB for unscaled data 13h 00h R/W Active video cropping stop LSB for unscaled data 14h 00h R/W Genlock/RTC 15h 01h R/W Horizontal sync start 16h 80h R/W Ancillary SAV/EAV control 17h 52h R/W Vertical blanking start 18h 00h R/W Vertical blanking stop 19h 00h R/W Chrominance processing control #1 1Ah 0Ch R/W Chrominance processing control #2 1Bh 14h R/W Interrupt reset register B 1Ch 00h R/W Interrupt enable register B 1Dh 00h R/W REGISTER FUNCTION (1) 26 R = Read only, W = Write only, R/W = Read and write Internal Control Registers Copyright © 2007–2010, Texas Instruments Incorporated Submit Documentation Feedback Product Folder Link(s): TVP5154A TVP5154A www.ti.com SLES214C – DECEMBER 2007 – REVISED SEPTEMBER 2010 Table 7-1. Direct Register Summary (continued) ADDRESS DEFAULT R/W (1) Interrupt configuration register B 1Eh 00h R/W Output control 1Fh 00h R/W Reserved 20h 21h–22h 00h R/W Indirect Register Address 23h 00h R/W Indirect Register Read/Write Strobe 24h 00h R/W 25h–26h 00h R/W 28h 00h R/W 29h–2Ah 00h R/W REGISTER FUNCTION Indirect Register Data AVID start/control for scaled data Reserved Video standard AVID stop for scaled data 27h Reserved 2Bh Cb gain factor 2Ch R Cr gain factor 2Dh R Reserved 656 Revision Select Reserved 2Eh–2Fh 30 00h R/W 31h–7Dh Patch Write Address 7Eh 00h R/W (2) Patch Code Execute 7Fh 00h R/W(2) MSB of device ID 80h 51h R LSB of device ID 81h 54h R ROM major version 82h 02h R ROM minor version 83h 00h R Vertical line count MSB 84h R Vertical line count LSB 85h R Interrupt status register B 86h R Interrupt active register B 87h R Status register #1 88h R Status register #2 89h R Status register #3 8Ah R Status register #4 8Bh R Status register #5 8Ch R Reserved 8Dh Patch Read Address 8Eh Reserved 8Fh 00h R/W(2) Closed caption data registers 90h–93h R WSS/CGMS-A data registers 94h–99h R VPS/Gemstar 2x data registers 9Ah–A6h R VITC data registers A7h–AFh R VBI FIFO read data B0h R Teletext filter 1 B1h–B5h 00h R/W Teletext filter 2 B6h–BAh 00h R/W BBh 00h R/W Teletext filter enable Reserved BCh–BFh Interrupt status register A C0h 00h R/W Interrupt enable register A C1h 00h R/W Interrupt configuration C2h 04h R/W (2) These registers are used for firmware patch code and should not be written to or read from during normal operation. Internal Control Registers Copyright © 2007–2010, Texas Instruments Incorporated Submit Documentation Feedback Product Folder Link(s): TVP5154A 27 TVP5154A SLES214C – DECEMBER 2007 – REVISED SEPTEMBER 2010 www.ti.com Table 7-1. Direct Register Summary (continued) ADDRESS DEFAULT R/W (1) VDP configuration RAM data C3h B8h R/W Configuration RAM address low byte C4h 1Fh R/W Configuration RAM address high byte C5h 00h R/W VDP status register C6h FIFO word count C7h FIFO interrupt threshold C8h 80h R/W FIFO reset C9h 00h W Line number interrupt CAh 00h R/W Pixel alignment register low byte CBh 4Eh R/W Pixel alignment register high byte CCh 00h R/W FIFO output control CDh 01h R/W Reserved CEh Full field enable CFh 00h R/W D0h D1h–FBh 00h FFh R/W Full field mode register FCh 7Fh R/W Reserved FDh Decoder core write enables FEh 0Fh R/W Decoder core read enables FFh 00h R/W REGISTER FUNCTION Line mode registers 28 Internal Control Registers R R Copyright © 2007–2010, Texas Instruments Incorporated Submit Documentation Feedback Product Folder Link(s): TVP5154A TVP5154A www.ti.com 7.2 SLES214C – DECEMBER 2007 – REVISED SEPTEMBER 2010 Direct Register Definitions Direct registers are written to by performing a 3-byte I2C transaction: START : DEVICE_ID : SUB_ADDRESS : DATA : STOP Each direct register is eight bits wide. 7.2.1 Address Default 7 Video Input Source Selection #1 Register 00h 00h 6 5 Reserved 4 3 Black output 2 Reserved 1 Channel n source selection 0 S-video selection Channel n source selection: 0 = AIPnA selected (default) 1 = AIPnB selected Table 7-2. Analog Channel and Video Mode Selection INPUT(S) SELECTED Composite S-Video ADDRESS 00 BIT 1 BIT 0 AIPnA (default) 0 0 AIPnB 1 0 AIPnA (luma), AIPnB (chroma) x 1 Where n = 1, 2, 3, 4 Black output: 0 = Normal operation (default) 1 = Force black screen output (outputs synchronized) a. Forced to 10h in normal mode b. Forced to 01h in extended mode Internal Control Registers Copyright © 2007–2010, Texas Instruments Incorporated Submit Documentation Feedback Product Folder Link(s): TVP5154A 29 TVP5154A SLES214C – DECEMBER 2007 – REVISED SEPTEMBER 2010 7.2.2 www.ti.com Analog Channel Controls Register Address Default 01h 15h 7 6 Reserved 5 4 1 3 0 2 1 1 0 Automatic gain control Automatic gain control (AGC): 00 = AGC disabled (fixed gain value) 01 = AGC enabled (default) 10 = Reserved 11 = AGC frozen to the previously set value 7.2.3 Operation Mode Controls Register Address Default 02h 00h 7 Fast lock mode 6 Color burst reference enable 5 4 TV/VCR mode 3 Composite peak disable 2 Color subcarrier PLL frozen 1 Luma peak disable 0 Power down mode Fast lock mode: 0 = Normal operation (default) 1 = Fast lock mode. Locks within three fields if stable input signal and forced video standard. Color burst reference enable: 0 = Color burst reference for AGC disabled (default) 1 = Color burst reference for AGC enabled (not recommended) TV/VCR mode: 00 = Automatic mode determined by the internal detection circuit (default) 01 = Reserved 10 = VCR (nonstandard video) mode (recommended when using a camera locked to the AC line frequency) 11 = TV (standard video) mode With automatic detection enabled, unstable or nonstandard syncs on the input video forces the detector into the VCR mode. This turns off the comb filters and turns on the chroma trap filter. Composite peak disable: 0 = Composite peak protection enabled (default) 1 = Composite peak protection disabled Color subcarrier PLL frozen: 0 = Color subcarrier PLL increments by the internally generated phase increment (default). GLCO pin outputs the frequency increment. 1 = Color subcarrier PLL stops operating. GLCO pin outputs the frozen frequency increment. Luma peak disable 0 = Luma peak processing enabled (default) 1 = Luma peak processing disabled (recommended) Power-down mode: 0 = Normal operation (default) 1 = Power-down mode. A/Ds are turned off and internal clocks are reduced to minimum. 30 Internal Control Registers Copyright © 2007–2010, Texas Instruments Incorporated Submit Documentation Feedback Product Folder Link(s): TVP5154A TVP5154A www.ti.com 7.2.4 Address Default 7 VBKO SLES214C – DECEMBER 2007 – REVISED SEPTEMBER 2010 Miscellaneous Control Register 03h 01h 6 GPCL pin 5 GPCL output enable 4 Lock status (HVLK) 3 YCbCr output enable(TVPOE) 2 HSYNC, VSYNC/PALI, AVID, FID/GLCO output enable 1 Vertical blanking on/off 0 CLK output enable VBKO (pins 41, 60, 83, 102) function select: 0 = GPCL (default) 1 = VBLK Note, if these pins are not configured as outputs, they must not be left floating. A 10-kΩ pulldown resistor is recommended if not driven externally. GPCL (data is output based on state of bit 5): 0 = GPCL outputs 0 (default) 1 = GPCL outputs 1 GPCL output enable: 0 = GPCL is inactive (default). GPCL should not be programmed to 0 when register 0Fh bit 1 is 1 (programmed to be GPCL/VBLK). 1 = GPCL is output. Note that, if these pins are not configured as outputs, they must not be left floating. A 10-kΩ pulldown resistor is recommended if not driven externally. Lock status (HVLK) (configured along with register 0Fh, see Figure 7-1 for the relationship between the configuration shared pins): 0 = Terminal VSYNC/PALI outputs the PAL indicator (PALI) signal and terminal FID/GLCO outputs the field ID (FID) signal (default) (if terminals are configured to output PALI and FID in register 0Fh). 1 = Terminal VSYNC/PALI outputs the horizontal lock indicator (HLK) and terminal FID outputs the vertical lock indicator (VLK) (if terminals are configured to output PALI and FID in register 0Fh). These are additional functionalities that are provided for ease of use. YCbCr output enable: 0 = YOUT[7:0] high impedance (default) 1 = YOUT[7:0] active Note, if these pins are not configured as outputs, they must not be left floating. A 10-kΩ pulldown resistor is recommended if not driven externally. HSYNC, VSYNC/PALI, active video indicator (AVID), and FID/GLCO output enables: 0 = HSYNC, VSYNC/PALI, AVID, and FID/GLCO are high impedance (default). 1 = HSYNC, VSYNC/PALI, AVID, and FID/GLCO are active. Note, if these pins are not configured as outputs, they must not be left floating. A 10-kΩ pulldown resistor is recommended if not driven externally. Vertical blanking on/off: 0 = Vertical blanking (VBLK) off (default) 1 = Vertical blanking (VBLK) on CLK output enable: 0 = CLK output is high impedance. 1 = CLK output is enabled (default). Note: CLK edge and SCLK are configured through register 05h. Table 7-3. Digital Output Control (1) REGISTER 03h, BIT 3 (TVPOE) (1) REGISTER C2h, BIT 2 (VDPOE) (1) YCbCr OUTPUT 0 X High impedance X 0 High impedance 1 1 Active VDPOE default is 1 and TVPOE default is 0. Internal Control Registers Copyright © 2007–2010, Texas Instruments Incorporated Submit Documentation Feedback Product Folder Link(s): TVP5154A 31 TVP5154A SLES214C – DECEMBER 2007 – REVISED SEPTEMBER 2010 www.ti.com 0F(Bit 2) VSYNC/PALI 0F(Bit 4) LOCK24B VSYNC PALI HLK 0 HVLK 1 HVLK 1 VLK 0 0 0 M U X HLK/HVLK 1 M U X VLK/HVLK 1 FID 0 M U X PALI/HLK/HVLK 1 M U X FID/VLK/HVLK 0 GLCO 1 M U X VSYNC/PALI/HLK/HVLK M U X FID/GLCO/VLK/HVLK Pins 38, 57, 76, 95 Pins 37, 56, 75, 94 0F(Bit 6) LOCK23 0F(Bit 3) FID/GLCO 03(Bit 4) HVLK VBLK 1 GPCL 0 M U X VBLK/GPCL 1 INTREQ 03(Bit 7) VBKO 0 M U X INTREQ/GPCL//VBLK Pins 41, 60, 83, 102 CLK 0 PCLK 1 0F(Bit 1) INTREQ/GPCL/VBLK M U X PCLK/CLK Pins 42, 61, 84, 103 0F(Bit 0) CLK/PCLK NOTE: Also see the configuration shared pins register at subaddress 0Fh (Section 7.2.16). Figure 7-1. Configuration Shared Pins 32 Internal Control Registers Copyright © 2007–2010, Texas Instruments Incorporated Submit Documentation Feedback Product Folder Link(s): TVP5154A TVP5154A www.ti.com 7.2.5 SLES214C – DECEMBER 2007 – REVISED SEPTEMBER 2010 Autoswitch Mask Register Address Default 04h DCh 7 6 Reserved N443_OFF: 0= 1= PALN_OFF: 0= 1= PALM_OFF: 0= 1= SEC_OFF: 0= 1= 7.2.6 5 SEC_OFF 4 N443_OFF 3 PALN_OFF 2 PALM_OFF 1 0 Reserved NTSC443 is unmasked from the autoswitch process. Autoswitch does switch to NTSC443. NTSC443 is masked from the autoswitch process. Autoswitch does not switch to NTSC443 (default). PAL-N is unmasked from the autoswitch process. Autoswitch does switch to PAL-N. PAL-N is masked from the autoswitch process. Autoswitch does not switch to PAL-N (default). PAL-M is unmasked from the autoswitch process. Autoswitch does switch to PAL-M. PAL-M is masked from the autoswitch process. Autoswitch does not switch to PAL-M (default). SECAM is unmasked from the autoswitch process. Autoswitch does switch to SECAM (default). SECAM is masked from the autoswitch process. Autoswitch does not switch to SECAM. Clock Control Register Address Default 05h 08h 7 6 5 4 Reserved 3 SCLK OE 2 Reserved 1 SCLK edge 0 CLK edge CLK edge 0 = CLK data changes on falling edge of CLK. 1 = CLK data changes on rising edge of CLK. SCLK edge 0 = SCLK data changes on falling edge of SCLK. 1 = SCLK data changes on rising edge of SCLK. SCLK OE 0 = SCLK output disabled. Output is high impedance. 1 = SCLK output enabled. NOTE: CLK OE is configured through register 0x03 to maintain compatibility with the TVP5150 family of devices. 7.2.7 Color Killer Threshold Control Register Address Default 7 Reserved 06h 10h 6 5 Automatic color killer 4 3 2 Color killer threshold 1 0 Automatic color killer: 00 = Automatic mode (default) 01 = Reserved 10 = Color killer enabled, the CbCr terminals are forced to a zero color state. 11 = Color killer disabled Color killer threshold: 11111 = –30 dB (minimum) 10000 = –24 dB (default) 00000 = –18 dB (maximum) Internal Control Registers Copyright © 2007–2010, Texas Instruments Incorporated Submit Documentation Feedback Product Folder Link(s): TVP5154A 33 TVP5154A SLES214C – DECEMBER 2007 – REVISED SEPTEMBER 2010 7.2.8 www.ti.com Luminance Processing Control #1 Register Address Default 07h 60h 7 2× luma output enable 6 Pedestal not present 5 Disable raw header 4 Luma bypass enabled during vertical blanking 3 2 1 0 Luminance signal delay with respect to chrominance signal 2× luma output enable: 0 = Output depends on bit 4, luminance bypass enabled during vertical blanking (default). 1 = Outputs 2x luma samples during the entire frame. This bit takes precedence over bit 4. Pedestal not present: 0 = 7.5 IRE pedestal is present on the analog video input signal. 1 = Pedestal is not present on the analog video input signal (default). Disable raw header: 0 = Insert 656 ancillary headers for raw data 1 = Disable 656 ancillary headers and instead force dummy ones (0x40) (default) Luminance bypass enabled during vertical blanking: 0 = Disabled. If bit 7, 2× luma output enable, is 0, normal luminance processing occurs and YCbCr samples are output during the entire frame (default). 1 = Enabled. If bit 7, 2× luma output enable, is 0, normal luminance processing occurs and YCbCr samples are output during VACTIVE and 2× luma samples are output during VBLK. Luminance bypass occurs for the duration of the vertical blanking as defined by registers 18h and 19h. Luma signal delay with respect to chroma signal in pixel clock increments (range –8 to 7 pixel clocks): 1111 = –8 pixel clocks delay 1011 = –4 pixel clocks delay 1000 = –1 pixel clocks delay 0000 = 0 pixel clocks delay (default) 0011 = 3 pixel clocks delay 0111 = 7 pixel clocks delay 7.2.9 Luminance Processing Control #2 Register Address Default 7 Reserved 08h 00h 6 Luminance filter select 5 4 Reserved 3 2 Peaking gain 1 0 Reserved Luminance filter select: 0 = Luminance comb filter enabled (default) 1 = Luminance chroma trap filter enabled Peaking gain (sharpness): 00 = 0 (default) 01 = 0.5 10 = 1 11 = 2 Information on peaking frequency: ITU-R BT.601 sampling rate: all standards — peaking center frequency is 2.6 MHz 34 Internal Control Registers Copyright © 2007–2010, Texas Instruments Incorporated Submit Documentation Feedback Product Folder Link(s): TVP5154A TVP5154A www.ti.com 7.2.10 Address Default SLES214C – DECEMBER 2007 – REVISED SEPTEMBER 2010 Brightness Control Register 09h 80h 7 6 5 4 3 Brightness control 2 1 0 Brightness control: This register works for CVBS and S-Video luminance. 1111 1111 = 255 (bright) 1000 0000 = 128 (default) 0000 0000 = 0 (dark) The output black level relative to the nominal black level (16 out of 256) as a function of the Brightness[7:0] setting and the Contrast[7:0] setting is as follows. Black Level = nominal_black_level + (Brightness[7:0] - 128) + (438 / 4) × (1 – Contrast[7:0] / 128) 7.2.11 Color Saturation Control Register Address Default 0Ah 80h 7 6 5 4 3 Saturation control 2 1 0 Saturation control: This register works for CVBS and S-Video chrominance. 1111 1111 = 255 (maximum) 1000 0000 = 128 (default) 0000 0000 = 0 (no color) The total chrominance gain relative to the nominal chrominance gain as a function of the Saturation [7:0] setting is as follows. Chrominance Gain = nominal_chrominance_gain × (Saturation[7:0] / 128) 7.2.12 Hue Control Register (does not apply to SECAM) Address Default 7 0Bh 00h 6 5 4 3 2 1 0 Hue control Hue control: 0111 1111 = +180 degrees 0000 0000 = 0 degrees (default) 1000 0000 = –180 degrees Internal Control Registers Copyright © 2007–2010, Texas Instruments Incorporated Submit Documentation Feedback Product Folder Link(s): TVP5154A 35 TVP5154A SLES214C – DECEMBER 2007 – REVISED SEPTEMBER 2010 www.ti.com 7.2.13 Contrast Control Register Address Default 0Ch 80h 7 6 5 4 3 2 1 0 Contrast [7:0] Contrast [7:0]: This register works for CVBS and S-Video luminance. 1111 1111 to 1101 Reserved 0000 = 1100 1111 = 207 (maximum contrast) 1000 0000 = 128 (default) 0000 0000 = 0 (minimum contrast) The total luminance gain relative to the nominal luminance gain as a function of the Contrast [7:0] setting is as follows. Luminance Gain = nominal_luminance_gain × (Contrast[7:0] / 128) Note: Luminance peak processing (see bit 1 of subaddress: 02h) may limit the upper end of the contrast control range. Note: Whenever the contrast control setting is modified, the brightness control setting must be modified immediately afterward to maintain the proper output black level. 7.2.14 Outputs and Data Rates Select Register Address Default 7 Reserved 0Dh 47h 6 YCbCr output code range 5 CbCr code format 4 3 YCbCr data path bypass 2 1 0 YCbCr output format YCbCr output code range: 0 = ITU-R BT.601 coding range (Y ranges from 16 to 235. U and V range from 16 to 240) 1 = Extended coding range (Y, U, and V range from 1 to 254) (default) CbCr code format: 0 = Offset binary code (2s complement + 128) (default) 1 = Straight binary code (2s complement) YCbCr data path bypass: 00 = Normal operation (default) 01 = Decimation filter output connects directly to the YCbCr output pins. This data is similar to the digitized composite data, but the HBLANK area is replaced with ITU-R BT.656 digital blanking. 10 = Digitized composite (or digitized S-video luma). A/D output connects directly to the YCbCr output pins. 11 = Reserved YCbCr output format: 000 = 8-bit 4:2:2 YCbCr with discrete sync output 001 = Reserved 010 = Reserved 011 = Reserved 100 = Reserved 101 = Reserved 110 = Reserved 111 = 8-bit ITU-R BT.656 interface with embedded sync output (default) 36 Internal Control Registers Copyright © 2007–2010, Texas Instruments Incorporated Submit Documentation Feedback Product Folder Link(s): TVP5154A TVP5154A www.ti.com SLES214C – DECEMBER 2007 – REVISED SEPTEMBER 2010 7.2.15 Luminance Processing Control #3 Register Address Default 7 0Eh 00h 6 5 4 3 2 Reserved 1 0 Luminance trap filter select Luminance filter stop band bandwidth (MHz): 00 = No notch (default) 01 = Notch 1 10 = Notch 2 11 = Notch Luminance filter select [1:0] selects one of the four chroma trap (notch) filters to produce luminance signal by removing the chrominance signal from the composite video signal. The stopband of the chroma trap filter is centered at the chroma subcarrier frequency, with stopband bandwidth controlled by the two control bits. See Table 7-4 for the stopband bandwidths. The WCF bit is controlled in the chrominance control #2 register. Table 7-4. Luma Filter Selection WCF 0 1 FILTER SELECT NTSC/PAL/SECAM ITU-R BT.601 00 1.2214 01 0.8782 10 0.7297 11 0.4986 00 1.4170 01 1.0303 10 0.8438 11 0.5537 Internal Control Registers Copyright © 2007–2010, Texas Instruments Incorporated Submit Documentation Feedback Product Folder Link(s): TVP5154A 37 TVP5154A SLES214C – DECEMBER 2007 – REVISED SEPTEMBER 2010 7.2.16 Address Default 7 Reserved www.ti.com Configuration Shared Pins Register 0Fh 08h 6 FID PIN 5 Reserved 4 PALI PIN 3 FID/GLCO 2 VSYNC/PALI 1 INTREQ/GPCL/VBLK 0 CLK/PCLK FID PIN function select: 0 = FID (default, if bit 3 is selected to output FID) 1 = Lock indicator (indicates whether the device is locked vertically) PALI PIN function select: 0 = PALI (default, if bit 2 is selected to output PALI) 1 = Lock indicator (indicates whether the device is locked horizontally) FID/GLCO function select (see register 03h, Section 7.2.4, for enhanced functionality): 0 = FID 1 = GLCO (default) VSYNC/PALI function select (see register 03h, Section 7.2.4, for enhanced functionality): 0 = VSYNC (default) 1 = PALI INTREQ/GPCL/VBLK function select: 0 = INTREQ (default) 1 = GPCL or VBLK depending on bit 7 of register 03h CLK/PCLK (pins 42, 61, 84, 103) function select: 0 = CLK at 27 MHz (default) 1 = PCLK (1× pixel clock frequency at 13.5 MHz) See Figure 7-1 for the relationship between the configuration shared pins. 7.2.17 Address Default 7 Active Video Cropping Start Pixel MSB for Unscaled Data Register 11h 00h 6 5 4 3 AVID start pixel MSB [9:2] 2 1 0 Active video cropping start pixel MSB [9:2], set this register first before setting register 12h. The TVP5154A decoder updates the AVID start values only when register 12h is written to. This start pixel value is relative to the default values of the AVID start pixel. 38 Internal Control Registers Copyright © 2007–2010, Texas Instruments Incorporated Submit Documentation Feedback Product Folder Link(s): TVP5154A TVP5154A www.ti.com 7.2.18 SLES214C – DECEMBER 2007 – REVISED SEPTEMBER 2010 Active Video Cropping Start Pixel LSB for Unscaled Data Register Address Default 12h 00h 7 6 5 Reserved 4 3 2 AVID active 1 0 AVID start pixel LSB [1:0] AVID active: 0 = AVID out active in VBLK (default) 1 = AVID out inactive in VBLK AVID start [9:0] (combined registers 11h and 12h): 01 1111 1111 = 511 00 0000 0001 = 1 00 0000 0000 = 0 (default) 11 1111 1111 = –1 10 0000 0000 = –512 Active video cropping start pixel LSB [1:0]: The TVP5154A decoder updates the AVID start values only when this register is written to. 7.2.19 Address Default Active Video Cropping Stop Pixel MSB LSB for Unscaled Data Register 13h 00h 7 6 5 4 3 AVID stop pixel MSB [9:2] 2 1 0 Active video cropping stop pixel MSB [9:2], set this register first before setting the register 14h. The TVP5154A decoder updates the AVID stop values only when register 14h is written to. This stop pixel value is relative to the default values of the AVID stop pixel. 7.2.20 Address Default 7 Active Video Cropping Stop Pixel LSB for Unscaled Data Register 14h 00h 6 5 4 3 Reserved 2 1 0 AVID stop pixel LSB [1:0] Active video cropping stop pixel LSB [1:0]: The number of pixels of active video must be an even number. The TVP5154A decoder updates the AVID stop values only when this register is written to. AVID stop [9:0] (combined registers 13h and 14h): 01 1111 1111 = 511 00 0000 0001 = 1 00 0000 0000 = 0 (default) (see Figure 3-5) and Figure 3-6) 11 1111 1111 = –1 10 0000 0000 = –512 Internal Control Registers Copyright © 2007–2010, Texas Instruments Incorporated Submit Documentation Feedback Product Folder Link(s): TVP5154A 39 TVP5154A SLES214C – DECEMBER 2007 – REVISED SEPTEMBER 2010 7.2.21 www.ti.com Genlock and RTC Register Address Default 15h 01h 7 Stable syncs 6 Reserved 5 4 3 Auto inc F/V bit control 2 1 GLCO/RTC 0 Stable syncs 0 = Output F and V bits follow the input signal producing fixed vertical blanking periods by adapting the active video. 1 = Output F and V bits produce fixed active video periods by adapting the vertical blanking. F/V bit control Table 7-5. F/V Bit Control BIT 5 BIT 4 0 0 0 NUMBER OF LINES 1 1 0 1 1 F BIT V BIT Standard ITU-R BT.656 ITU-R BT.656 Nonstandard even Force to 1 Switch at field boundary Nonstandard odd Toggles Switch at field boundary Standard ITU-R BT.656 ITU-R BT.656 Nonstandard Toggles Switch at field boundary Standard ITU-R BT.656 ITU-R BT.656 Nonstandard Pulse mode Switch at field boundary Illegal Auto inc: When this bit is set to 1, subsequent reading/writing from/to back door registers automatically increment the address index. GLCO/RTC: Table 7-6 for different modes. Table 7-6. GLCO/RTC Control BIT 2 BIT 1 BIT 0 0 x 0 GLCO GENLOCK/RTC MODE 0 x 1 RTC output mode 0 (default) 1 x 0 GLCO 1 x 1 RTC output mode 1 All other values are reserved. Figure 6-1 shows the timing of GLCO and the timing of RTC. 40 Internal Control Registers Copyright © 2007–2010, Texas Instruments Incorporated Submit Documentation Feedback Product Folder Link(s): TVP5154A TVP5154A www.ti.com 7.2.22 Address Default SLES214C – DECEMBER 2007 – REVISED SEPTEMBER 2010 Horizontal Sync (HSYNC) Start Register 16h 80h 7 6 5 4 3 2 1 0 HSYNC start HSYNC start: 1111 1111 = 1111 1110 = 1000 0001 = 1000 0000 = 0111 1111 = 0111 1110 = 0000 0000 = –127 × 4 pixel clocks –126 × 4 pixel clocks –1 × 4 pixel clocks 0 pixel clocks (default) 1 × 4 pixel clocks 2 × 4 pixel clocks 128 × 4 pixel clocks BT.656 SAV Code BT.656 EAV Code YOUT[7:0] U Y V Y F F 0 0 0 0 X Y 8 0 1 0 8 0 1 0 F F 0 0 0 0 X Y U Y HSYNC AVID 128 SCLK Start of Digital Active Line Nhbhs Nhb Figure 7-2. Horizontal Sync Table 7-7. Clock Delays (CLKs) STANDARD Nhbhs Nhb NTSC 16 272 PAL 20 284 SECAM 40 280 Detailed timing information is also available in Section 3.12, Synchronization Signals. Internal Control Registers Copyright © 2007–2010, Texas Instruments Incorporated Submit Documentation Feedback Product Folder Link(s): TVP5154A 41 TVP5154A SLES214C – DECEMBER 2007 – REVISED SEPTEMBER 2010 7.2.23 www.ti.com Ancillary SAV/EAV Control Address Default 7 Reserved 17h 52h 6 Scaler PD 5 Include scale ancillary 4 Include scale SAV 3 Include scale EAV 2 Include unscale ancillary 1 Include unscale SAV 0 Include unscale EAV Include unscaled EAV: 0 = AVID period does not include the EAV sync codes (default). 1 = AVID period includes the EAV sync codes. Include unscaled SAV: 0 = AVID period does not include the SAV sync codes. 1 = AVID period includes the SAV sync codes (default). Include unscaled ancillary data: 0 = AVID period includes the ancillary data region (default). 1 = AVID period does not include the ancillary data region. Include scaled EAV: 0 = AVID period does not include the EAV sync codes (default). 1 = AVID period includes the EAV sync codes. Include scaled SAV: 0 = AVID period does not include the SAV sync codes. 1 = AVID period includes the SAV sync codes (default). Include scaled ancillary data: 0 = AVID period includes the ancillary data region (default). 1 = AVID period does not include the ancillary data region. Scaler PD (scaler power down): 0 = Scaler active 1 = Scaler powered down (default) 42 Internal Control Registers Copyright © 2007–2010, Texas Instruments Incorporated Submit Documentation Feedback Product Folder Link(s): TVP5154A TVP5154A www.ti.com SLES214C – DECEMBER 2007 – REVISED SEPTEMBER 2010 Data SAV EAV Pixel Data ANC Unscaled pixel data AVID Include SAV = 0, Include EAV = 0, Include ancillary = 1 AVID Include SAV = 1, Include EAV = 0, Include ancillary = 0 AVID Data Include SAV = 0, Include EAV = 1, Include ancillary = 1 SAV Pixel Data EAV ANC Scaled pixel data, AVID start/stop reduced AVID Include SAV = 0, Include EAV = 0, Include ancillary = 1 AVID Include SAV = 1, Include EAV = 0, Include ancillary = 0 AVID Include SAV = 0, Include EAV = 1, Include ancillary = 1 Figure 7-3. AVID Behavior When Ancillary Data Present Internal Control Registers Copyright © 2007–2010, Texas Instruments Incorporated Submit Documentation Feedback Product Folder Link(s): TVP5154A 43 TVP5154A SLES214C – DECEMBER 2007 – REVISED SEPTEMBER 2010 Data www.ti.com SAV Pixel Data EAV Unscaled pixel data AVID Include SAV = 0, Include EAV = 0 AVID Include SAV = 1, Include EAV = 0 AVID Include SAV = 0, Include EAV = 1 Data SAV 0 Data Pixel Data EAV Scaled pixel data, AVID start/stop same as for un−scaled data AVID Include SAV = 0, Include EAV = 0 AVID Include SAV = 1, Include EAV = 0 AVID Include SAV = 0, Include EAV = 1 Data SAV Pixel Data EAV Scaled pixel data, AVID start/stop reduced AVID Include SAV = 0, Include EAV = 0 AVID Include SAV = 1, Include EAV = 0 AVID Include SAV = 0, Include EAV = 1 Figure 7-4. AVID Behavior When No Ancillary Data Present 44 Internal Control Registers Copyright © 2007–2010, Texas Instruments Incorporated Submit Documentation Feedback Product Folder Link(s): TVP5154A TVP5154A www.ti.com 7.2.24 SLES214C – DECEMBER 2007 – REVISED SEPTEMBER 2010 Vertical Blanking Start Register Address Default 18h 00h 7 6 5 4 3 Vertical blanking start 2 1 0 Vertical blanking (VBLK) start: 0111 1111 = 127 lines after start of vertical blanking interval 0000 0001 = 1 line after start of vertical blanking interval 0000 0000 = Same time as start of vertical blanking interval (default) (see Figure 3-4, Figure 3-5, and Figure 3-6) 1111 1111 = 1 line before start of vertical blanking interval 1000 0000 = 128 lines before start of vertical blanking interval Vertical register register register 7.2.25 blanking is adjustable with respect to the standard vertical blanking intervals. The setting in this determines the timing of the GPCL/VBLK signal when it is configured to output vertical blank (see 03h). The setting in this register also determines the duration of the luma bypass function (see 07h). Vertical Blanking Stop Register Address Default 7 19h 00h 6 5 4 3 Vertical blanking stop 2 1 0 Vertical blanking (VBLK) stop: 0111 1111 = 127 lines after stop of vertical blanking interval 0000 0001 = 1 line after stop of vertical blanking interval 0000 0000 = Same time as stop of vertical blanking interval (default) (see Figure 3-4, Figure 3-5, and Figure 3-6) 1111 1111 = 1 line before stop of vertical blanking interval 1000 0000 = 128 lines before stop of vertical blanking interval Vertical register register register blanking is adjustable with respect to the standard vertical blanking intervals. The setting in this determines the timing of the GPCL/VBLK signal when it is configured to output vertical blank (see 03h). The setting in this register also determines the duration of the luma bypass function (see 07h). Internal Control Registers Copyright © 2007–2010, Texas Instruments Incorporated Submit Documentation Feedback Product Folder Link(s): TVP5154A 45 TVP5154A SLES214C – DECEMBER 2007 – REVISED SEPTEMBER 2010 7.2.26 www.ti.com Chrominance Control #1 Register Address Default 1Ah 0Ch 7 6 5 Reserved color 4 PLL reset 3 Chrominance adaptive comb filter enable (ACE) 2 Chrominance comb filter enable (CE) 1 0 Automatic color gain control Color PLL reset: 0 = Color PLL not reset (default) 1 = Color PLL reset Writing a 1 to this bit resets the color PLL and transmits a 1 in the reset bit of the GLCO output stream. Chrominance adaptive comb filter enable (ACE): 0 = Disable 1 = Enable (default) Chrominance comb filter enable (CE): 0 = Disable 1 = Enable (default) Automatic color gain control (ACGC): 00 = ACGC enabled (default) 01 = Reserved 10 = ACGC disabled 11 = ACGC frozen to the previously set value 7.2.27 Address Default 7 Chrominance Control #2 Register 1Bh 14h 6 5 4 Reserved 3 Reserved 2 WCF 1 0 Chrominance filter select Wideband chroma filter (WCF): 0 = Disable 1 = Enable (default) Chrominance filter select: 00 = No notch (default) 01 = Notch 1 10 = Notch 2 11 = Notch 3 Chrominance output bandwidth (MHz), see Table 7-8 Table 7-8. Chroma Output Bandwidth Select WCF 0 1 46 FILTER SELECT NTSC/PAL/SECAM ITU-R BT.601 00 1.2214 01 0.8782 10 0.7297 11 0.4986 00 1.4170 01 1.0303 10 0.8438 11 0.5537 Internal Control Registers Copyright © 2007–2010, Texas Instruments Incorporated Submit Documentation Feedback Product Folder Link(s): TVP5154A TVP5154A www.ti.com 7.2.28 SLES214C – DECEMBER 2007 – REVISED SEPTEMBER 2010 Interrupt Reset Register B Address Default 7 Software initialization reset 1Ch 00h 6 Reserved 5 Reserved 4 Field rate changed reset 3 Line alternation changed reset 2 Color lock changed reset 1 H/V lock changed reset 0 TV/VCR changed reset Interrupt reset register B is used by the external processor to reset the interrupt status bits in interrupt status register B. Bits loaded with a 1 allow the corresponding interrupt status bit to reset to 0. Bits loaded with a 0 have no effect on the interrupt status bits. Software initialization reset: 0 = No effect (default) 1 = Reset software initialization bit Field rate changed reset: 0 = No effect (default) 1 = Reset field rate changed bit Line alternation changed reset: 0 = No effect (default) 1 = Reset line alternation changed bit Color lock changed reset: 0 = No effect (default) 1 = Reset color lock changed bit H/V lock changed reset: 0 = No effect (default) 1 = Reset H/V lock changed bit TV/VCR changed reset [TV/VCR mode is determined by counting the total number of lines/frame. The mode switches to VCR for nonstandard number of lines]: 0 = No effect (default) 1 = Reset TV/VCR changed bit Internal Control Registers Copyright © 2007–2010, Texas Instruments Incorporated Submit Documentation Feedback Product Folder Link(s): TVP5154A 47 TVP5154A SLES214C – DECEMBER 2007 – REVISED SEPTEMBER 2010 7.2.29 Address Default www.ti.com Interrupt Enable Register B 1Dh 00h 7 Software initialization occurred enable 6 Reserved 5 Reserved 4 Field rate changed 3 Line alternation changed 2 Color lock changed 1 H/V lock changed 0 TV/VCR changed Software initialization occurred enable: 0 = Disabled (default) 1 = Enabled Field rate changed: 0 = Disabled (default) 1 = Enabled Line alternation changed: 0 = Disabled (default) 1 = Enabled Color lock changed: 0 = Disabled (default) 1 = Enabled H/V lock changed: 0 = Disabled (default) 1 = Enabled TV/VCR changed: 0 = Disabled (default) 1 = Enabled Interrupt enable register B is used by the external processor to mask unnecessary interrupt sources for interrupt B. Bits loaded with a 1 allow the corresponding interrupt condition to generate an interrupt on the external pin. Conversely, bits loaded with zeros mask the corresponding interrupt condition from generating an interrupt on the external pin. This register only affects the external pin; it does not affect the bits in the interrupt status register. A given condition can set the appropriate bit in the status register and not cause an interrupt on the external pin. To determine if this device is driving the interrupt pin, either AND interrupt status register B with interrupt enable register B, or check the state of interrupt B in the interrupt B active register. 48 Internal Control Registers Copyright © 2007–2010, Texas Instruments Incorporated Submit Documentation Feedback Product Folder Link(s): TVP5154A TVP5154A www.ti.com 7.2.30 SLES214C – DECEMBER 2007 – REVISED SEPTEMBER 2010 Interrupt Configuration Register B Address Default 1Eh 00h 7 6 5 4 Reserved 3 2 1 0 Interrupt polarity B Interrupt polarity B: 0 = Interrupt B is active low (default). 1 = Interrupt B is active high. Interrupt polarity B must be same as interrupt polarity A bit at bit 0 of the interrupt configuration register A at address C2h. Interrupt configuration register B is used to configure the polarity of interrupt B on the external interrupt pin. When the interrupt B is configured for active low, the pin is driven low when active and high impedance when inactive (open drain). Conversely, when the interrupt B is configured for active high, it is driven high for active and driven low for inactive. 7.2.31 Indirect Register Data Address Default 21h-22h 00h Address 22h 21h 7 6 5 4 3 2 1 0 Data[15:8] Data[7:0] I2C registers 21h and 22h can be used to write data to or read data from indirect registers. See I2C registers 23h and 24h. 7.2.32 Indirect Register Address Address Default 7 23h 00h 6 5 4 3 2 1 0 ADDR[7:0] ADDR[7:0] = LSB of indirect address Internal Control Registers Copyright © 2007–2010, Texas Instruments Incorporated Submit Documentation Feedback Product Folder Link(s): TVP5154A 49 TVP5154A SLES214C – DECEMBER 2007 – REVISED SEPTEMBER 2010 www.ti.com 7.2.33 Indirect Register Read/Write Strobe Address Default 7 24h 00h 6 5 4 3 2 1 0 R/W[7:0] This register selects the most significant bits of the indirect register address and performs either an indirect read or write operation. Data will be written from are read to Indirect Register Data registers 21h-22h. R/W[7:0]: 01h = read from 00h-1FFh address bank 02h = write to 00h-1FFh address bank 03h = read from 200h-3FFh address bank 04h = write to 200h-3FFh address bank 05h = read from 300h-3FFh address bank 06h = write to 300h-3FFh address bank 50 Internal Control Registers Copyright © 2007–2010, Texas Instruments Incorporated Submit Documentation Feedback Product Folder Link(s): TVP5154A TVP5154A www.ti.com SLES214C – DECEMBER 2007 – REVISED SEPTEMBER 2010 7.2.34 Output Control Address Default 1Fh 00h 7 6 Bit swap 5 Ancillary Enable 4 Parity modifier 3 SAV/EAV modifier 2 1 Output mode 0 Output mode: 000 = Mode 0 : Unscaled data clocked by clock 1 001 = Mode 1 : Scaled data clocked by clock 1 010 = Mode 2 : Multiplexed data with separate clocks 011 = Mode 3 : Multiplexed data with clock 1 at 54 MHz 100 = Mode 4 : Unscaled/scaled field toggled data clocked by clock 1 SAV/EAV modifier: 0 = SAV/EAV codes not modified 1 = SAV/EAV MSB modified. MSB = 1 indicates unscaled data, MSB = 0 indicates scaled data Parity modifier: 0 = Parity calculation includes SAV/EAV MSB. 1 = Parity calculation does not include SAV/EAV MSB. Ancillary enable: 0 = Ancillary data not enabled 1 = Ancillary data packet added to indicate scaled or unscaled data Note : Scaled/unscaled ancillary data cannot be enabled at the same time as VBI ancillary data Bit swap: 0 = chx_out(0) corresponds to data LSB, chx_out(7) corresponds to data MSB 1 = chx_out(0) corresponds to data MSB, chx_out(7) corresponds to data LSB Table 7-9. Ancillary Data Format and Sequence BYTE NO. D7 (MSB) D6 D5 D4 D3 D2 D1 D0 (LSB) 0 0 0 0 0 0 0 0 0 1 1 1 1 1 1 1 1 1 2 1 1 1 1 1 1 1 1 3 NEP EP 0 1 DID3 DID2 DID1 DID0 4 1 0 0 0 0 0 0 0 Secondary data ID (SDID) 5 0 1 0 0 0 0 0 1 Number of 32 bit data (NN) 6 Z Video line # [7:0] 0 0 0 0 DESCRIPTION Ancillary data preamble Data ID (DID) Internal data ID0 (IDID0) 0 0 Video line # [9:8] Internal data ID1 (IDID1) 8 00h Data byte 9 00h Data byte 10 1 0 11 1 0 EP: NEP: DID: SDID: NN: IDID0: IDID1: CS: Fill byte: 00h 0 0 0 Data Check sum 0 0 0 Fill byte Even parity for D0–D5 Negated even parity For unscaled data D0–D3 taken from EAV DID value for unscaled data stream register low nibble for field 0 and from high nibble for field 1 For scaled data D0–D3 taken from EAV DID value for scaled data stream register low nibble for field 0 and from high nibble for field 1 Zero data Indicates 1 D word of data Transaction video line number [7:0] Bit 0/1 = Transaction video line number [9:8] Sum of D0–D7 of DID through last data byte Fill bytes make a multiple of four bytes from byte 0 to last fill byte. For teletext modes, byte 8 is the sync pattern byte. Byte 9 is 1. Data (the first data byte). Internal Control Registers Copyright © 2007–2010, Texas Instruments Incorporated Submit Documentation Feedback Product Folder Link(s): TVP5154A 51 TVP5154A SLES214C – DECEMBER 2007 – REVISED SEPTEMBER 2010 7.2.35 Address Default www.ti.com Active Video Cropping Start Pixel MSB for Scaled Data Register 25h 00h 7 6 5 4 3 AVID start pixel MSB [9:2] 2 1 0 Active video cropping start pixel MSB [9:2], set this register first before setting register 26h. The TVP5154A decoder updates the AVID start values only when register 26h is written to. This start pixel value is relative to the default values of the AVID start pixel. 7.2.36 Active Video Cropping Start Pixel LSB for Scaled Data Register Address Default 7 26h 00h 6 5 4 3 Reserved 2 Active 1 0 AVID start pixel LSB [1:0] AVID active: 0 = AVID out active in VBLK (default) 1 = AVID out inactive in VBLK Active video cropping start pixel LSB [1:0]: The TVP5154A decoder updates the AVID start values only when this register is written to. AVID start [9:0]: 01 1111 1111 = 511 00 0000 0001 = 1 00 0000 0000 = 0 (default) 11 1111 1111 = –1 10 0000 0000 = –512 52 Internal Control Registers Copyright © 2007–2010, Texas Instruments Incorporated Submit Documentation Feedback Product Folder Link(s): TVP5154A TVP5154A www.ti.com 7.2.37 SLES214C – DECEMBER 2007 – REVISED SEPTEMBER 2010 Video Standard Register Address Default 28h 00h 7 6 5 4 3 2 Reserved Video standard: 0000 = 0001 = 0010 = 0011 = 0100 = 0101 = 0110 = 0111 = 1000 = 1001 = 1010 = 1011 = 1100 = 1 0 Video standard Autoswitch mode (default) Reserved (M, J) NTSC ITU-R BT.601 Reserved (B, G, H, I, N) PAL ITU-R BT.601 Reserved (M) PAL ITU-R BT.601 Reserved (Combination-N) PAL ITU-R BT.601 Reserved NTSC 4.43 ITU-R BT.601 Reserved SECAM ITU-R BT.601 With the autoswitch code running, the user can force the device to operate in a particular video standard mode and sample rate by writing the appropriate value into this register. 7.2.38 Address Default Active Video Cropping Stop Pixel MSB for Scaled Data Register 29h 00h 7 6 5 4 3 AVID stop pixel MSB [9:2] 2 1 0 Active video cropping stop pixel MSB [9:2], set this register first before setting the register 2Ah. The TVP5154A decoder updates the AVID stop values only when register 2Ah is written to. This stop pixel value is relative to the default values of the AVID stop pixel. 7.2.39 Active Video Cropping Stop Pixel LSB for Scaled Data Register Address Default 7 2Ah 00h 6 5 4 3 Reserved AVID stop [9:0]: 01 1111 1111 = 00 0000 0001 = 00 0000 0000 = 11 1111 1111 = 10 0000 0000 = 2 1 0 AVID stop pixel LSB [1:0] 511 1 0 (default) (see Figure 3-4, Figure 3-5, and Figure 3-6) –1 –512 Active video cropping stop pixel LSB [1:0]: The number of pixels of active video must be an even number. The TVP5154A decoder updates the AVID stop values only when this register is written to. Internal Control Registers Copyright © 2007–2010, Texas Instruments Incorporated Submit Documentation Feedback Product Folder Link(s): TVP5154A 53 TVP5154A SLES214C – DECEMBER 2007 – REVISED SEPTEMBER 2010 7.2.40 Address www.ti.com Cb Gain Factor Register 2Ch 7 6 5 4 3 2 1 0 Cb gain factor This is a read-only register that provides the gain applied to the Cb in the YCbCr data stream. 7.2.41 Address Cr Gain Factor Register 2Dh 7 6 5 4 3 2 1 0 Cr gain factor This is a read-only register that provides the gain applied to the Cr in the YCbCr data stream. 7.2.42 Address Default 656 Revision Select Register 30h 00h 7 6 5 4 3 2 1 0 656 Rev 4 3 MSB of device ID 2 1 0 2 1 0 656 revision select: 0 = Adheres to ITU-R BT.656-4 and BT.656-5 timing (default) 1 = Adheres to ITU-R BT.656-3 timing 7.2.43 Address Default MSB of Device ID Register 80h 51h 7 6 5 This register identifies the MSB of the device ID. Value = 0x51. 7.2.44 Patch Write Address Address Default 7 7Eh 00h 6 5 4 3 R/W[7:0] This register is used for downloading firmware patch code. Please refer to the patch load application note for more detail. This register must not be written to or read from during normal operation. 54 Internal Control Registers Copyright © 2007–2010, Texas Instruments Incorporated Submit Documentation Feedback Product Folder Link(s): TVP5154A TVP5154A www.ti.com SLES214C – DECEMBER 2007 – REVISED SEPTEMBER 2010 7.2.45 Patch Code Execute Address Default 7Fh 00h 7 6 5 4 3 2 1 0 R/W[7:0] Writing to this register following a firmware patch load restarts the CPU and initiates execution of the patch code. This register must not be written to or read from during normal operation. 7.2.46 LSB of Device ID Register Address Default 81h 54h 7 6 5 4 3 LSB of device ID 2 1 0 2 1 0 This register identifies the LSB of the device ID. Value = 0x54. 7.2.47 ROM Major Version Register Address Default 7 (1) 82h 02h 6 5 4 3 ROM major version (1) This register can contain a number from 0x01 to 0xFF. Internal Control Registers Copyright © 2007–2010, Texas Instruments Incorporated Submit Documentation Feedback Product Folder Link(s): TVP5154A 55 TVP5154A SLES214C – DECEMBER 2007 – REVISED SEPTEMBER 2010 7.2.48 Address Default ROM Minor Version Register 83h 00h 7 (1) www.ti.com 6 5 4 3 ROM minor version (1) 2 1 0 This register can contain a number from 0x01 to 0xFF. 7.2.49 Address Vertical Line Count MSB Register 84h 7 6 5 4 3 2 Reserved 1 0 Vertical line count MSB Vertical line count bits [9:8] 7.2.50 Address 7 Vertical Line Count LSB Register 85h 6 5 4 3 Vertical line count LSB 2 1 0 Vertical line count bits [7:0] Registers 84h and 85h can be read and combined to extract the detected number of lines per frame. This can be used with nonstandard video signals, such as a VCR in fast-forward or rewind modes, to synchronize the downstream video circuitry. 56 Internal Control Registers Copyright © 2007–2010, Texas Instruments Incorporated Submit Documentation Feedback Product Folder Link(s): TVP5154A TVP5154A www.ti.com 7.2.51 SLES214C – DECEMBER 2007 – REVISED SEPTEMBER 2010 Interrupt Status Register B Address 7 Software initialization 86h 6 Reserved 5 Command ready 4 Field rate changed 3 Line alternation changed 2 Color lock changed 1 H/V lock changed 0 TV/VCR changed Software initialization: 0 = Software initialization is not ready (default). 1 = Software initialization is ready. Command ready: 0 = TVP5154A is not ready to accept a new command (default). 1 = TVP5154A is ready to accept a new command. Field rate changed: 0 = Field rate has not changed (default). 1 = Field rate has changed. Line alternation changed: 0 = Line alteration has not changed (default). 1 = Line alternation has changed. Color lock changed: 0 = Color lock status has not changed (default). 1 = Color lock status has changed. H/V lock changed: 0 = H/V lock status has not changed (default). 1 = H/V lock status has changed. TV/VCR changed: 0 = TV/VCR status has not changed (default). 1 = TV/VCR status has changed. Interrupt status register B is polled by the external processor to determine the interrupt source for interrupt B. After an interrupt condition is set, it can be reset by writing to the interrupt reset register B at subaddress 1Ch with a 1 in the appropriate bit. Internal Control Registers Copyright © 2007–2010, Texas Instruments Incorporated Submit Documentation Feedback Product Folder Link(s): TVP5154A 57 TVP5154A SLES214C – DECEMBER 2007 – REVISED SEPTEMBER 2010 7.2.52 www.ti.com Interrupt Active Register B Address 87h 7 6 5 4 Reserved 3 2 1 0 Interrupt B Interrupt B: 0 = Interrupt B is not active on the external terminal (default). 1 = Interrupt B is active on the external terminal. The interrupt active register B is polled by the external processor to determine if interrupt B is active. 7.2.53 Status Register #1 Address 7 Peak white detect status 88h 6 Line-alternating status 5 Field rate status 4 Lost lock detect 3 Color subcarrier lock status 2 Vertical sync lock status 1 Horizontal sync lock status 0 TV/VCR status Peak white detect status: 0 = Peak white is not detected. 1 = Peak white is detected. Line–alternating status: 0 = Nonline alternating 1 = Line alternating Field rate status: 0 = 60 Hz 1 = 50 Hz Lost lock detect: 0 = No lost lock since status register #1 was last read 1 = Lost lock since status register #1 was last read Color subcarrier lock status: 0 = Color subcarrier is not locked. 1 = Color subcarrier is locked. Vertical sync lock status: 0 = Vertical sync is not locked. 1 = Vertical sync is locked. Horizontal sync lock status: 0 = Horizontal sync is not locked. 1 = Horizontal sync is locked. TV/VCR status. TV mode is determined by detecting standard line-to-line variations and specific chroma SCH phases based on the standard input video format. VCR mode is determined by detecting variations in the chroma SCH phases compared to the chroma SCH phases of the standard input video format. 0 = TV 1 = VCR 58 Internal Control Registers Copyright © 2007–2010, Texas Instruments Incorporated Submit Documentation Feedback Product Folder Link(s): TVP5154A TVP5154A www.ti.com 7.2.54 SLES214C – DECEMBER 2007 – REVISED SEPTEMBER 2010 Status Register #2 Address 7 Reserved 89h 6 Weak signal detection 5 PAL switch polarity 4 Field sequence status 3 AGC and offset frozen status 2 1 0 Reserved Weak signal detection: 0 = No weak signal 1 = Weak signal mode PAL switch polarity of first line of odd field: 0 = PAL switch is 0. 1 = PAL switch is 1. Field sequence status: 0 = Even field 1 = Odd field AGC and offset frozen status: 0 = AGC and offset are not frozen. 1 = AGC and offset are frozen. 7.2.55 Status Register #3 Address 7 8Ah 6 5 4 3 Analog gain 2 1 0 Digital gain Analog gain: 4-bit front-end AGC analog gain setting Digital gain: 4 MSBs of 6-bit front-end AGC digital gain setting The product of the analog and digital gain is given below. Gain Product = (1 + 3 × analog_gain/15) × (1 + gain_step × digital_gain/4096) Where, 0 ≤ analog_gain ≤ 15 0 ≤ digital_gain ≤ 63 The gain_step setting as a function of the analog_gain setting is shown below. analog_gain 0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 gain_step 61 55 48 44 38 33 29 26 24 22 20 19 18 17 16 15 Internal Control Registers Copyright © 2007–2010, Texas Instruments Incorporated Submit Documentation Feedback Product Folder Link(s): TVP5154A 59 TVP5154A SLES214C – DECEMBER 2007 – REVISED SEPTEMBER 2010 www.ti.com 7.2.56 Status Register #4 Address 8Bh 7 6 5 4 3 Subcarrier to horizontal (SCH) phase 2 1 0 SCH (color PLL subcarrier phase at 50% of the falling edge of horizontal sync of line one of odd field; step size 360°/256): 0000 0000 = 0.00o 0000 0001 = 1.41o 0000 0010 = 2.81o 1111 1110 = 357.2o 1111 1111 = 358.6o 7.2.57 Status Register #5 Address 8Ch 7 Autoswitch mode 6 5 Reserved 4 3 2 Video standard 1 0 Sampling rate Autoswitch mode: 0 = Stand-alone (forced video standard) mode 1 = Autoswitch mode This register contains information about the detected video standard and the sampling rate at which the device is currently operating. When autoswitch code is running, this register must be tested to determine which video standard has been detected. Table 7-10. Auto Switch Video Standard SR (1) VIDEO STANDARD [3:1] (1) 60 VIDEO STANDARD BIT 3 BIT 2 BIT 1 BIT 0 0 0 0 0 Reserved 0 0 0 1 (M, J) NTSC ITU-R BT.601 0 0 1 0 Reserved 0 0 1 1 (B, G, H, I, N) PAL ITU-R BT.601 0 1 0 0 Reserved 0 1 0 1 (M) PAL ITU-R BT.601 0 1 1 0 Reserved 0 1 1 1 PAL-Nc ITU-R BT.601 1 0 0 0 Reserved 1 0 0 1 NTSC 4.43 ITU-R BT.601 1 0 1 0 Reserved 1 0 1 1 SECAM ITU-R BT.601 Sampling rate (SR): 0 = Reserved, 1 = ITU-R BT.601 Internal Control Registers Copyright © 2007–2010, Texas Instruments Incorporated Submit Documentation Feedback Product Folder Link(s): TVP5154A TVP5154A www.ti.com SLES214C – DECEMBER 2007 – REVISED SEPTEMBER 2010 7.2.58 Patch Read Address Address Default 8Eh 00h 7 6 5 4 3 2 1 0 R/W[7:0] This register can be used for patch code read-back. This register must not be written to or read from during normal operation. 7.2.59 Closed Caption Data Registers Address Address 90h 91h 92h 93h 90h–93h 7 6 5 4 Closed Closed Closed Closed 3 caption field 1 byte caption field 1 byte caption field 2 byte caption field 2 byte 2 1 0 1 2 1 2 These registers contain the closed caption data arranged in bytes per field. Internal Control Registers Copyright © 2007–2010, Texas Instruments Incorporated Submit Documentation Feedback Product Folder Link(s): TVP5154A 61 TVP5154A SLES214C – DECEMBER 2007 – REVISED SEPTEMBER 2010 www.ti.com 7.2.60 WSS/CGMS-A Data Registers Address 94h–99h NTSC Address 94h 95h 96h 97h 98h 99h 7 6 b13 b12 b13 b12 5 b5 b11 b19 b5 b11 b19 4 b4 b10 b18 b4 b10 b18 3 b3 b9 b17 b3 b9 b17 2 b2 b8 b16 b2 b8 b16 1 b1 b7 b15 b1 b7 b15 0 b0 b6 b14 b0 b6 b14 WSS field 1 WSS field 1 WSS field 1 WSS field 2 WSS field 2 WSS field 2 BYTE byte 1 byte 2 byte 3 byte 1 byte 2 byte 3 These registers contain the wide screen signaling (WSS/CGMS-A) data for NTSC. Bits 0–1 represent word 0, aspect ratio. Bits 2–5 represent word 1, header code for word 2. Bits 6–13 represent word 2, copy control. Bits 14–19 represent word 3, CRC. PAL/SECAM Address 94h 95h 96h 97h 98h 99h Bits Bits Bits Bits 62 7 b7 6 b6 5 b5 b13 b7 b6 b5 b13 4 3 b4 b3 b12 b11 Reserved b4 b3 b12 b11 Reserved 2 b2 b10 1 b1 b9 0 b0 b8 BYTE WSS field 1 byte 1 WSS field 1 byte 2 b2 b10 b1 b9 b0 b8 WSS field 2 byte 1 WSS field 2 byte 2 0–3 represent group 1, aspect ratio. 4–7 represent group 2, enhanced services. 8–10 represent group 3, subtitles. 11–13 represent group 4, others. Internal Control Registers Copyright © 2007–2010, Texas Instruments Incorporated Submit Documentation Feedback Product Folder Link(s): TVP5154A TVP5154A www.ti.com SLES214C – DECEMBER 2007 – REVISED SEPTEMBER 2010 7.2.61 VPS/Gemstar 2x Data Registers Address 9Ah–A6h Address 9Ah 9Bh 9Ch 9Dh 9Eh 9Fh A0h A1h A2h A3h A4h A5h A6h 7 6 5 4 3 VPS/Gemstar 2x byte 1 VPS/Gemstar 2x byte 2 VPS/Gemstar 2x byte 3 VPS/Gemstar 2x byte 4 VPS/Gemstar 2x byte 5 VPS/Gemstar 2x byte 6 VPS/Gemstar 2x byte 7 VPS/Gemstar 2x byte 8 VPS/Gemstar 2x byte 9 VPS/Gemstar 2x byte 10 VPS/Gemstar 2x byte 11 VPS/Gemstar 2x byte 12 VPS/Gemstar 2x byte 13 2 1 0 When PAL VPS is used, these registers contain the entire VPS data line except the clock run-in code and the start code. When NTSC Gemstar 2x is used, these registers contain the Gemstar 2x data. 7.2.62 VITC Data Registers Address A7h–AFh Address A7h A8h A9h AAh ABh ACh ADh AEh AFh 7 6 5 4 3 VITC byte 1, frame byte 1 VITC byte 2, frame byte 2 VITC byte 3, seconds byte 1 VITC byte 4, seconds byte 2 VITC byte 5, minutes byte 1 VITC byte 6, minutes byte 2 VITC byte 7, hour byte 1 VITC byte 8, hour byte 2 VITC byte 9, CRC 2 1 0 These registers contain the VITC data. 7.2.63 Address 7 VBI FIFO Read Data Register B0h 6 5 4 3 2 1 0 FIFO read data This address is provided to access VBI data in the FIFO through the host port. All forms of teletext data come directly from the FIFO, while all other forms of VBI data can be programmed to come from the registers or from the FIFO. Current status of the FIFO can be found at address C6h and the number of bytes in the FIFO is located at address C7h. If the host port is to be used to read data from the FIFO, the output formatter must be disabled at address CDh bit 0. The format used for the VBI FIFO is shown in Section 3.9. Internal Control Registers Copyright © 2007–2010, Texas Instruments Incorporated Submit Documentation Feedback Product Folder Link(s): TVP5154A 63 TVP5154A SLES214C – DECEMBER 2007 – REVISED SEPTEMBER 2010 7.2.64 www.ti.com Teletext Filter and Mask Registers Address Default Address B1h B2h B3h B4h B5h B6h B7h B8h B9h BAh B1h–BAh 00h 7 6 Filter Filter Filter Filter Filter Filter Filter Filter Filter Filter 1 1 1 1 1 2 2 2 2 2 5 mask 1 mask 2 mask 3 mask 4 mask 5 mask 1 mask 2 mask 3 mask 4 mask 5 4 3 2 Filter Filter Filter Filter Filter Filter Filter Filter Filter Filter 1 1 1 1 1 2 2 2 2 2 1 pattern 1 pattern 2 pattern 3 pattern 4 pattern 5 pattern 1 pattern 2 pattern 3 pattern 4 pattern 5 0 For an NABTS system, the packet prefix consists of five bytes. Each byte contains four data bits (D[3:0]) interlaced with four Hamming protection bits (H[3:0]): Bit 7 D[3] Bit 6 H[3] Bit 5 D[2] Bit 4 H[2] Bit 3 D[1] Bit 2 H[1] Bit 1 D[0] Bit 0 H[0] Only the data portion D[3:0] from each byte is applied to a teletext filter function with the corresponding pattern bits P[3:0] and mask bits M[3:0]. Hamming protection bits are ignored by the filter. For a WST system (PAL or NTSC), the packet prefix consists of two bytes so that two patterns are used. Patterns 3, 4, and 5 are ignored. The mask bits enable filtering using the corresponding bit in the pattern register. For example, a 1 in the LSB of mask 1 means that the filter module must compare the LSB of nibble 1 in the pattern register to the first data bit on the transaction. If these match, a true result is returned. A 0 in a bit of mask 1 means that the filter module must ignore that data bit of the transaction. If all zeros are programmed in the mask bits, the filter matches all patterns returning a true result (default 00h). Pattern and mask for each byte and filter are referred as <1,2><P,M><1,2,3,4,5> where: <1,2> identifies the filter 1 or 2 <P,M> identifies the pattern or mask <1,2,3,4,5> identifies the byte number 64 Internal Control Registers Copyright © 2007–2010, Texas Instruments Incorporated Submit Documentation Feedback Product Folder Link(s): TVP5154A TVP5154A www.ti.com SLES214C – DECEMBER 2007 – REVISED SEPTEMBER 2010 7.2.65 Teletext Filter Control Register Address Default 7 BBh 00h 6 Reserved 5 4 3 2 Mode Filter logic 1 TTX filter 2 enable 0 TTX filter 1 enable Filter logic: Allows different logic to be applied when combining the decision of filter 1 and filter 2 as follows: 00 = NOR (default) 01 = NAND 10 = OR 11 = AND Mode: 0 = Teletext WST PAL mode B (2 header bytes) (default) 1 = Teletext NABTS NTSC mode C (5 header bytes) TTX filter 2 enable: 0 = Disabled (default) 1 = Enabled TTX filter 1 enable: 0 = Disabled (default) 1 = Enabled If the filter matches or if the filter mask is all zeros, a true result is returned. 7.2.66 Address Default Interrupt Status Register A C0h 00h 7 Lock state interrupt 6 Lock interrupt 5 4 Reserved 3 2 FIFO threshold interrupt 1 Line interrupt 0 Data interrupt Lock state interrupt: 0 = TVP5154A is not locked to the video signal (default) 1 = TVP5154A is locked to the video signal. Lock interrupt: 0 = A transition has not occurred on the lock signal (default). 1 = A transition has occurred on the lock signal. FIFO threshold interrupt: 0 = The amount of data in the FIFO has not yet crossed the threshold programmed at address C8h (default). 1 = The amount of data in the FIFO has crossed the threshold programmed at address C8h. Line interrupt: 0 = The video line number has not yet been reached (default). 1 = The video line number programmed in address CAh has occurred. Data interrupt: 0 = No data is available (default). 1 = VBI data is available either in the FIFO or in the VBI data registers. The interrupt status register A can be polled by the host processor to determine the source of an interrupt. After an interrupt condition is set it can be reset by writing to this register with a 1 in the appropriate bit(s). Internal Control Registers Copyright © 2007–2010, Texas Instruments Incorporated Submit Documentation Feedback Product Folder Link(s): TVP5154A 65 TVP5154A SLES214C – DECEMBER 2007 – REVISED SEPTEMBER 2010 www.ti.com 7.2.67 Interrupt Enable Register A Address Default 7 Reserved C1h 00h 6 Lock interrupt enable 5 Cycle complete interrupt enable 4 Bus error interrupt enable 3 Reserved 2 FIFO threshold interrupt enable 1 Line interrupt enable 0 Data interrupt enable Lock interrupt enable: 0 = Disabled (default) 1 = Enabled Cycle complete interrupt enable: 0 = Disabled (default) 1 = Enabled Bus error interrupt enable: 0 = Disabled (default) 1 = Enabled FIFO threshold interrupt enable: 0 = Disabled (default) 1 = Enabled Line interrupt enable: 0 = Disabled (default) 1 = Enabled Data interrupt enable: 0 = Disabled (default) 1 = Enabled The interrupt enable register A is used by the host processor to mask unnecessary interrupt sources. Bits loaded with a 1 allow the corresponding interrupt condition to generate an interrupt on the external pin. Conversely, bits loaded with a 0 mask the corresponding interrupt condition from generating an interrupt on the external pin. This register only affects the interrupt on the external terminal, it does not affect the bits in interrupt status register A. A given condition can set the appropriate bit in the status register and not cause an interrupt on the external terminal. To determine if this device is driving the interrupt terminal either perform a logical AND of interrupt status register A with interrupt enable register A, or check the state of the interrupt A bit in the interrupt configuration register at address C2h. 66 Internal Control Registers Copyright © 2007–2010, Texas Instruments Incorporated Submit Documentation Feedback Product Folder Link(s): TVP5154A TVP5154A www.ti.com SLES214C – DECEMBER 2007 – REVISED SEPTEMBER 2010 7.2.68 Interrupt Configuration Register A Address Default 7 C2h 04h 6 5 Reserved 4 3 2 YCbCr enable (VDPOE) 1 Interrupt A 0 Interrupt polarity A YCbCr enable (VDPOE): 0 = YCbCr pins are high impedance. 1 = YCbCr pins are active if other conditions are met (default). Interrupt A (read only): 0 = Interrupt A is not active on the external pin (default). 1 = Interrupt A is active on the external pin. Interrupt polarity A: 0 = Interrupt A is active low (default). 1 = Interrupt A is active high. Interrupt configuration register A is used to configure the polarity of the external interrupt terminal. When interrupt A is configured as active low, the terminal is driven low when active and high impedance when inactive (open collector). Conversely, when the terminal is configured as active high, it is driven high when active and driven low when inactive. 7.2.69 VDP Configuration RAM Register Address Default Address C3h C4h C5h C3h B8h 7 C4h 1Fh C5h 00h 6 5 4 3 Configuration data RAM address (7:0) Reserved 2 1 0 RAM address 8 The configuration RAM data is provided to initialize the VDP with initial constants. The configuration RAM is 512 bytes organized as 32 different configurations of 16 bytes each. The first 12 configurations are defined for the current VBI standards. An additional two configurations can be used as a custom programmed mode for unique standards, such as Gemstar. Address C3h is used to read or write to the RAM. The RAM internal address counter is automatically incremented with each transaction. Addresses C5h and C4h make up a 9-bit address to load the internal address counter with a specific start address. This can be used to write a subset of the RAM for only those standards of interest. Registers D0h–FBh must all be programmed with FFh before writing or reading the configuration RAM. Full field mode (CFh) must be disabled as well. The suggested RAM contents are shown in Table 7-11. All values are hexadecimal. Table 7-11. VBI Configuration RAM for Signals With Pedestal INDEX ADDRESS 0 1 2 3 4 5 6 7 8 9 A B C D E F WST SECAM 000 AA AA FF FF E7 2E 20 A6 E4 B4 0E 0 7 0 10 0 WST SECAM 010 AA AA FF FF E7 2E 20 A6 E4 B4 0E 0 7 0 10 0 WST PAL B 020 AA AA FF FF 27 2E 20 AB A4 72 10 0 7 0 10 0 WST PAL B 030 AA AA FF FF 27 2E 20 AB A4 72 10 0 7 0 10 0 WST PAL C 040 AA AA FF FF E7 2E 20 22 A4 98 0D 0 0 0 10 0 WST PAL C 050 AA AA FF FF E7 2E 20 22 A4 98 0D 0 0 0 10 0 WST NTSC 060 AA AA FF FF 27 2E 20 23 63 93 0D 0 0 0 10 0 WST NTSC 070 AA AA FF FF 27 2E 20 23 63 93 0D 0 0 0 10 0 NABTS, NTSC 080 AA AA FF FF E7 2E 20 A2 63 93 0D 0 7 0 15 0 Internal Control Registers Copyright © 2007–2010, Texas Instruments Incorporated Submit Documentation Feedback Product Folder Link(s): TVP5154A 67 TVP5154A SLES214C – DECEMBER 2007 – REVISED SEPTEMBER 2010 www.ti.com Table 7-11. VBI Configuration RAM for Signals With Pedestal (continued) ADDRESS 0 1 2 3 4 5 6 7 8 9 A B C D E F NABTS, NTSC INDEX 090 AA AA FF FF E7 2E 20 A2 63 93 0D 0 7 0 15 0 NABTS, NTSC-J 0A0 AA AA FF FF A7 2E 20 A3 63 93 0D 0 7 0 10 0 NABTS, NTSC-J 0B0 AA AA FF FF A7 2E 20 A3 63 93 0D 0 7 0 10 0 CC, PAL/SECAM 0C0 AA 2A FF 3F 04 51 6E 02 A4 7B 09 0 0 0 27 0 CC, PAL/SECAM 0D0 AA 2A FF 3F 04 51 6E 02 A4 7B 09 0 0 0 27 0 CC, NTSC 0E0 AA 2A FF 3F 04 51 6E 02 63 8C 09 0 0 0 27 0 CC, NTSC 0F0 AA 2A FF 3F 04 51 6E 02 63 8C 09 0 0 0 27 0 WSS/CGMS-A, PAL/SECAM 100 5B 55 C5 FF 0 71 6E 42 A4 CD 0F 0 0 0 3A 0 WSS/CGMS-A, PAL/SECAM 110 5B 55 C5 FF 0 71 6E 42 A4 CD 0F 0 0 0 3A 0 WSS/CGMS-A, NTSC C 120 38 00 3F 00 0 71 6E 43 63 7C 08 0 0 0 39 0 WSS/CGMS-A, NTSC C 130 38 00 3F 00 0 71 6E 43 63 7C 08 0 0 0 39 0 VITC, PAL/SECAM 140 0 0 0 0 0 8F 6D 49 A4 85 08 0 0 0 4C 0 VITC, PAL/SECAM 150 0 0 0 0 0 8F 6D 49 A4 85 08 0 0 0 4C 0 VITC, NTSC 160 0 0 0 0 0 8F 6D 49 63 94 08 0 0 0 4C 0 VITC, NTSC 170 0 0 0 0 0 8F 6D 49 63 94 08 0 0 0 4C 0 VPS, PAL 180 AA AA FF FF BA CE 2B 8D A4 DA 0B 0 7 0 60 0 VPS, PAL 190 AA AA FF FF BA CE 2B 8D A4 DA 0B 0 7 0 60 0 Gemstar 2x Custom 1 1A0 99 99 FF FF 05 51 6E 05 63 18 13 80 00 00 60 00 Gemstar 2x Custom 1 1B0 99 99 FF FF 05 51 6E 05 63 18 13 80 00 00 60 00 Custom 2 1C0 Programmable Custom 2 1D0 Programmable 68 Internal Control Registers Copyright © 2007–2010, Texas Instruments Incorporated Submit Documentation Feedback Product Folder Link(s): TVP5154A TVP5154A www.ti.com 7.2.70 Address 7 FIFO full error SLES214C – DECEMBER 2007 – REVISED SEPTEMBER 2010 VDP Status Register C6h 6 FIFO empty 5 TTX available 4 CC field 1 available 3 CC field 2 available 2 WSS/CGMS-A available 1 VPS/Gemstar 2x available 0 VITC available The VDP status register indicates whether data is available in either the FIFO or data registers, and status information about the FIFO. Reading data from the corresponding register does not clear the status flags automatically. These flags are only reset by writing a 1 to the respective bit. However, bit 6 is updated automatically. FIFO full error: 0 = No FIFO full error 1 = FIFO was full during a write to FIFO. The FIFO full error flag is set when the current line of VBI data can not enter the FIFO. For example, if the FIFO has only ten bytes left and teletext is the current VBI line, the FIFO full error flag is set, but no data is written because the entire teletext line will not fit. However, if the next VBI line is closed caption requiring only two bytes of data plus the header, this goes into the FIFO (even if the full error flag is set). FIFO empty: 0 = FIFO is not empty. 1 = FIFO is empty. TTX available: 0 = Teletext data is not available. 1 = Teletext data is available. CC field 1 available: 0 = Closed caption data from field 1 is not available. 1 = Closed caption data from field 1 is available. CC field 2 available: 0 = Closed caption data from field 2 is not available. 1 = Closed caption data from field 2 is available. WSS/CGMS-A available: 0 = WSS/CGMS-A data is not available. 1 = WSS/CGMS-A data is available. VPS/Gemstar 2x available 0 = VPS/Gemstar 2x data is not available. 1 = VPS/Gemstar 2x data is available. VITC available: 0 = VITC data is not available. 1 = VITC data is available. 7.2.71 Address 7 FIFO Word Count Register C7h 6 5 4 3 Number of words 2 1 0 This register provides the number of words in the FIFO. One word equals two bytes. Internal Control Registers Copyright © 2007–2010, Texas Instruments Incorporated Submit Documentation Feedback Product Folder Link(s): TVP5154A 69 TVP5154A SLES214C – DECEMBER 2007 – REVISED SEPTEMBER 2010 7.2.72 www.ti.com FIFO Interrupt Threshold Register Address Default C8h 80h 7 6 5 4 3 Number of words 2 1 0 This register is programmed to trigger an interrupt when the number of words in the FIFO exceeds this value (default 80h). This interrupt must be enabled at address C1h. One word equals two bytes. 7.2.73 FIFO Reset Register Address Default C9h 00h 7 6 5 4 3 2 1 0 Any data Writing any data to this register resets the FIFO and clears any data present in both the FIFO and the VDP registers. 7.2.74 Line Number Interrupt Register Address Default CAh 00h 7 Field 1 enable 6 Field 2 enable 5 4 3 2 Line number 1 0 This register is programmed to trigger an interrupt when the video line number matches this value in bits 5:0. This interrupt must be enabled at address C1h. The value of 0 or 1 does not generate an interrupt. Field 1 enable: 0 = Disabled (default) 1 = Enabled Field 2 enable: 0 = Disabled (default) 1 = Enabled Line number: (default 00h) 7.2.75 Pixel Alignment Registers Address Default Address CBh CCh CBh 4Eh 7 CCh 00h 6 5 4 3 Switch pixel [7:0] Reserved 2 1 0 Switch pixel [9:8] These registers form a 10-bit horizontal pixel position from the falling edge of sync, where the VDP controller initiates the program from one line standard to the next line standard; for example, the previous line of teletext to the next line of closed caption. This value must be set so that the switch occurs after the previous transaction has cleared the delay in the VDP, but early enough to allow the new values to be programmed before the current settings are required. 70 Internal Control Registers Copyright © 2007–2010, Texas Instruments Incorporated Submit Documentation Feedback Product Folder Link(s): TVP5154A TVP5154A www.ti.com SLES214C – DECEMBER 2007 – REVISED SEPTEMBER 2010 7.2.76 FIFO Output Control Register Address Default 7 CDh 01h 6 5 4 Reserved 3 2 1 0 Host access enable This register is programmed to allow I2C access to the FIFO or allowing all VDP data to go out the video port. Host access enable: 0 = Output FIFO data to the video output Y[7:0] 1 = Allow I2C access to the FIFO data (default) 7.2.77 Full Field Enable Register Address Default 7 CFh 00h 6 5 4 Reserved 3 2 1 0 Full field enable This register enables the full field mode. In this mode, all lines outside the vertical blank area and all lines in the line mode registers programmed with FFh are sliced with the definition of register FCh. Values other than FFh in the line mode registers allow a different slice mode for that particular line. Full field enable: 0 = Disable full field mode (default) 1 = Enable full field mode Internal Control Registers Copyright © 2007–2010, Texas Instruments Incorporated Submit Documentation Feedback Product Folder Link(s): TVP5154A 71 TVP5154A SLES214C – DECEMBER 2007 – REVISED SEPTEMBER 2010 7.2.78 Line Mode Registers Address Default Address D0h D1h D2h D3h D4h D5h D6h D7h D8h D9h DAh DBh DCh DDh DEh DFh E0h E1h E2h E3h E4h E5h E6h E7h E8h E9h EAh EBh ECh EDh EEh EFh F0h F1h F2h F3h F4h F5h F6h F7h F8h F9h FAh FBh 72 www.ti.com D0h 00h D1h–FBh FFh 7 6 5 4 3 Line 6 Field 1 Line 6 Field 2 Line 7 Field 1 Line 7 Field 2 Line 8 Field 1 Line 8 Field 2 Line 9 Field 1 Line 9 Field 2 Line 10 Field 1 Line 10 Field 2 Line 11 Field 1 Line 11 Field 2 Line 12 Field 1 Line 12 Field 2 Line 13 Field 1 Line 13 Field 2 Line 14 Field 1 Line 14 Field 2 Line 15 Field 1 Line 15 Field 2 Line 16 Field 1 Line 16 Field 2 Line 17 Field 1 Line 17 Field 2 Line 18 Field 1 Line 18 Field 2 Line 19 Field 1 Line 19 Field 2 Line 20 Field 1 Line 20 Field 2 Line 21 Field 1 Line 21 Field 2 Line 22 Field 1 Line 22 Field 2 Line 23 Field 1 Line 23 Field 2 Line 24 Field 1 Line 24 Field 2 Line 25 Field 1 Line 25 Field 2 Line 26 Field 1 Line 26 Field 2 Line 27 Field 1 Line 27 Field 2 Internal Control Registers 2 1 0 Copyright © 2007–2010, Texas Instruments Incorporated Submit Documentation Feedback Product Folder Link(s): TVP5154A TVP5154A www.ti.com SLES214C – DECEMBER 2007 – REVISED SEPTEMBER 2010 These registers program the specific VBI standard at a specific line in the video field. Bit 7: 0 = Disable filtering of null bytes in closed caption modes. 1 = Enable filtering of null bytes in closed caption modes (default). In teletext modes, bit 7 enables the data filter function for that particular line. If it is set to 0, the data filter passes all data on that line. Bit 6: 0 = Send VBI data to registers only. 1 = Send VBI data to FIFO and the registers. Teletext data only goes to FIFO. (default) Bit 5: 0 = Allow VBI data with errors in the FIFO. 1 = Do not allow VBI data with errors in the FIFO (default). Bit 4: 0 = Do not enable error detection and correction. 1 = Enable error detection and correction (when bits [3:0] = 1 2, 3, and 4 only) (default). Bits [3:0]: 0000 = WST SECAM 0001 = WST PAL B 0010 = WST PAL C 0011 = WST NTSC 0100 = NABTS NTSC C 0101 = NABTS NTSC D 0110 = CC PAL 0111 = CC NTSC 1000 = WSS/CGMS-A PAL 1001 = WSS/CGMS-A NTSC 1010 = VITC PAL 1011 = VITC NTSC 1100 = VPS PAL 1101 = Gemstar 2x Custom 1 1110 = Custom 2 1111 = Active video (VDP off) (default) A value of FFh in the line mode registers is required for any line to be sliced as part of the full field mode. Internal Control Registers Copyright © 2007–2010, Texas Instruments Incorporated Submit Documentation Feedback Product Folder Link(s): TVP5154A 73 TVP5154A SLES214C – DECEMBER 2007 – REVISED SEPTEMBER 2010 www.ti.com 7.2.79 Full Field Mode Register Address Default 7 FCh 7Fh 6 5 4 3 Full field mode 2 1 0 This register programs the specific VBI standard for full field mode. It can be any VBI standard. Individual line settings take priority over the full field register. This allows each VBI line to be programmed independently but have the remaining lines in full field mode. The full field mode register has the same definitions as the line mode registers (default 7Fh). 7.2.80 Decoder Write Enable Register Address Default FEh 0Fh 7 6 5 4 Reserved 3 Decoder 4 2 Decoder 3 1 Decoder 2 0 Decoder 1 This register controls which of the four decoder cores receives I2C write transactions. A 1 in the corresponding bit position enables the decoder to receive write commands. Any combination of decoders can be configured to receive write commands, allowing all four decoders to be programmed concurrently. 7.2.81 Decoder Read Enable Register Address Default 7 FFh 00h 6 5 Reserved 4 3 Decoder 4 2 Decoder 3 1 Decoder 2 0 Decoder 1 This register controls which of the four decoder cores responds to I2C read transactions. A 1 in the corresponding bit position enables the decoder to respond to read commands. If more than one decoder is enabled for reading, only the lowest numbered decoder responds. Reads from multiple decoders at the same time is not possible. Note that when register 0xFE is written to with any value, register 0xFF is set to 0x00. Likewise, when register 0xFF is written to with any value, register 0xFE is set to 0x00. 74 Internal Control Registers Copyright © 2007–2010, Texas Instruments Incorporated Submit Documentation Feedback Product Folder Link(s): TVP5154A TVP5154A www.ti.com 7.3 SLES214C – DECEMBER 2007 – REVISED SEPTEMBER 2010 Indirect Register Definitions To write to the TVP5154A indirect registers, it is required that the registers be unlocked using a password. The password prevents undesirable writes into the device at start-up due to power surges, for example. The following example demonstrates the method for unlocking the indirect registers. After writing to the desired indirect registers described in the following text, it is recommended that the device be locked again. • Unlock the device 1. Write 0x51 to I2C_0x21. //MSB data 2. Write 0x54 to I2C_0x22. //LSB data 3. Write 0xFF to I2C_0x23. //Data address 4. Write 0x04 to I2C_0x24. //Write command • Lock the device 1. Write 0x00 to I2C_0x21. //MSB data 2. Write 0x00 to I2C_0x22. //LSB data 3. Write 0xFF to I2C_0x23. //Data address 4. Write 0x04 to I2C_0x24. //Write command Indirect registers are written to by performing the following I2C transaction: START : DEVICE_ID_w : 0x21 : DATA_HIGH : STOP START : DEVICE_ID_w : 0x22 : DATA_LOW : STOP START : DEVICE_ID_w : 0x23 : ADDRESS_LOW : STOP START : DEVICE_ID_w : 0x24 : WR_STROBE : STOP To read from an indirect register, the following I2C transaction should be performed: START : DEVICE_ID_w : 0x23 : ADDRESS_LOW : STOP START : DEVICE_ID_w : 0x24 : RD_STROBE : STOP START : DEVICE_ID_r : 0x21 : data_msb : STOP START : DEVICE_ID_r : 0x22 : data_lsb : STOP Where: DEVICE_ID_w is the selected TVP5154A device ID with the read/write bit (LSB) set to write. DEVICE_ID_r is the selected TVP5154A device ID with the read/write bit (LSB) set to read. ADDRESS_LOW is the low byte of the register address. WR_STROBE is 0x06. RD_STROBE is 0x05. Note, the upper byte of the address is not directly used but is replaced by the corresponding STROBE signal. Each indirect register is 16 bits wide. Internal Control Registers Copyright © 2007–2010, Texas Instruments Incorporated Submit Documentation Feedback Product Folder Link(s): TVP5154A 75 TVP5154A SLES214C – DECEMBER 2007 – REVISED SEPTEMBER 2010 7.3.1 www.ti.com DID Control Address Default 7 15 36Ah 000h 6 Unscaled field 1 DID 5 4 3 2 1 Unscaled field 0 DID 0 14 13 Scaled field 1 DID 12 11 10 9 Scaled field 0 DID 8 This register controls the value of the EAV DID bytes for scaled and unscaled data. The value for each field can be independently set, allowing identification of both which field is being processed and whether the data comes from the scaled or unscaled channel. 7.3.2 Misc Control Address Default 36Bh 0Ch 7 6 5 4 3 Clock rate 15 14 2 1 Clock OE 13 12 11 Scaled blank data 0 Clock edge 10 9 8 Scaled blank data: When no active scaled data is available, this value is output during the active video region. Clock rate: This register controls various clock modes. Since this register is modified by the device during normal operation, the clock rate bits should not be modified by the user. Clock OE: This register controls various clock modes. Since this register is modified by the device during normal operation, the clock rate bits should not be modified by the user. Clock edge: This register controls various clock modes. Since this register is modified by the device during normal operation, the clock rate bits should not be modified by the user. 7.3.3 Interleave Field Control 1 Address Default 36Dh 0h 7 6 15 14 Field count 5 4 3 End pixel count[7:0] 13 12 11 Reserved 2 10 Blank timing 1 0 9 8 End pixel count[9:8] End pixel count: Pixel count at which the frame status is updated. Do not change this value. Blank timing: 0: No timing signals are generated for blank fields. 1: H, V, and F timing generated for blank fields based on unscaled video timing sequences Field count: Number of output fields in field interleaved sequence 76 Internal Control Registers Copyright © 2007–2010, Texas Instruments Incorporated Submit Documentation Feedback Product Folder Link(s): TVP5154A TVP5154A www.ti.com 7.3.4 SLES214C – DECEMBER 2007 – REVISED SEPTEMBER 2010 Interleave Field Control 2 Address Default 36Eh 0h 7 6 5 Field mode(3) 15 14 13 Field mode(7) 7.3.5 4 3 Field mode(2) 2 1 Field mode(1) 12 11 Field mode(6) 0 Field mode(0) 10 9 Field mode(5) 8 Field mode(4) Interleave Field Control 3 Address Default 36Fh 0h 7 6 5 Field mode(11) 15 4 3 Field mode(10) 14 13 Field mode(15) 2 1 Field mode(9) 12 11 Field mode(14) 0 Field mode(8) 10 9 Field mode(13) 8 Field mode(12) These registers allow the output data stream to toggle between unscaled and scaled data on a field basis. By setting Field mode[n] appropriately, it is possible to use the available output bandwidth to interleave unscaled and scaled frames to achieve reduced frame rates, while still maintaining compatibility with legacy data receivers. These registers can also be used to reduce the frame rate of either unscaled data or scaled data by disabling fields within the sequence. A counter automatically moves from Field mode[0] to Field mode[n] where n can be 0 through 15, then returns back to Field mode[0]. Depending on the value of Field mode[n], either unscaled data, scaled data, or no data is sent for the current frame. 00 = Unscaled data 01 = Null frame (no SAV/EAV sequence will be generated) 10 = Scaled data 11 = Reserved The values programmed for registers 3A8h and 3A9h are different for NTSC (also NTSC4.43 and PAL-M) and for PAL (also PAL-Nc and SECAM). 7.3.6 Vertical Scaling Field 1 Control Address Default 7 3A8h 0h 6 5 4 3 2 1 0 11 10 9 8 V_Field1[8] V_Field1[7:0] 15 14 13 12 Reserved Vertical scaling initial value in field 1 [8:0]: Initial value of vertical accumulator for field 1 For NTSC: V_Field1 = (1.5 × V_Field2) – 128 If V_Field 1 is negative, add V_Field2 to V_Field1 and add V_Field2 to V_Field2 until V_Field1 is positive. For PAL: V_Field1 = (Vdesired/Vactive) × 256 Internal Control Registers Copyright © 2007–2010, Texas Instruments Incorporated Submit Documentation Feedback Product Folder Link(s): TVP5154A 77 TVP5154A SLES214C – DECEMBER 2007 – REVISED SEPTEMBER 2010 7.3.7 www.ti.com Vertical Scaling Field 2 Control Address Default 3A9h 0h 7 6 5 4 3 2 1 0 11 10 9 8 V_Field2[8] 0 V_Field2[7:0] 15 14 13 12 Reserved Vertical scaling initial value in field 2 [8:0]: Initial value of vertical accumulator for field 2 For NTSC: V_Field2 = (Vdesired/Vactive) × 256 For PAL: V_Field2 = (1.5 × V_Field1) – 128 If V_Field 2 is negative, add V_Field1 to V_Field2 and add V_Field1 to V_Field1 until V_Field2 is positive. 7.3.8 Scaler Output Active Pixels Address Default 3ABh 2D0h 7 6 5 15 14 13 4 3 SCAL_PIXEL[7:0] 2 1 12 11 10 9 8 SCAL_PIXEL[9:8] 4 3 VERT_COEF[7:0] 2 1 0 10 Reserved 9 8 VERT_COEF[8] Reserved SCAL_PIXEL [9:0]: Scaler active pixel outputs per line 7.3.9 Vertical Scaling Control Address Default 3ACh 2100h 7 15 6 5 14 13 1 Reserved 12 Enable 11 Enabled: Enable vertical and horizontal scaler 0 = Disable scaler (default) 1 = Enable scaler VERT_COEF [8:0]: Vertical scaling coefficient VERT_COEF = (Vdesired/Vactive) × 256 7.3.10 Horizontal Scaling Control Address Default 3ADh 400h 7 6 5 4 3 HORZ_COEF[7:0] 2 1 0 15 Reserved 14 13 12 10 9 8 HORZ_COEF[14:0]: 78 11 HORZ_COEF[14:8] Horizontal scaling coefficient, MSB five bits are integer values and LSB ten bits are fraction numbers. HORZ_COEF = Hactive/Hdesired Internal Control Registers Copyright © 2007–2010, Texas Instruments Incorporated Submit Documentation Feedback Product Folder Link(s): TVP5154A TVP5154A www.ti.com SLES214C – DECEMBER 2007 – REVISED SEPTEMBER 2010 8 Scaler Configuration 8.1 Overview The TVP5154A contains four independent scalers, one for each video decoder channel. Each scaler is able to filter and scale both horizontally and vertically to different ratios. Horizontally, a 7-tap poly-phase filter is used to ensure optimal scaling performance and can be configured to scale to any output size below the input resolution, in decrements of two pixels. Vertically a running average filter is used to filter vertically and can be configured to scale to any output size below the input resolution. When scaling horizontally, the output pixels are packed together to allow continuous reading of the pixels. AVID should be configured so that it qualifies the active pixels, allowing the receiving back end to ignore nonactive pixels. When scaling vertically, inactive lines are not removed from the output since there is no internal frame memory. The receiving back end must use AVID to qualify active lines/pixels. AVID can be configured to be either active or inactive during invalid output lines. Due to the fact that vertical scaling is performed on a field basis, it is possible that the vertical resolution will be reduced due to filtering across lines within the field, rather than adjacent lines in the frame. Aliasing will not occur, but the output image will appear soft vertically. If the desired scaling ration is 0.5, this can be achieved by simply ignoring every other field. This maintains sharpness, but may introduce aliasing artifacts. 8.2 8.2.1 Horizontal Scaling Registers The horizontal scaler uses a 32-phase polymorphic filter. Excellent performance can be achieved by using the set of coefficients programmed into the 5154 for all scaling ratios. It is necessary to program the input and output scaling control registers (3AB and 3AD). Figure 8-1 shows how data is packed horizontally when scaled. Unscaled SAV EAV Scaled SAV EAV Figure 8-1. Unscaled and Scaled Pixel Data Alignment Scaler Configuration Copyright © 2007–2010, Texas Instruments Incorporated Submit Documentation Feedback Product Folder Link(s): TVP5154A 79 TVP5154A SLES214C – DECEMBER 2007 – REVISED SEPTEMBER 2010 8.3 8.3.1 www.ti.com Vertical Scaling Registers The vertical scaler implements a weighted running average filter, which requires the initial weights and the ratio registers to be configured. Additionally, it is necessary to program the input and output scaling control registers (3A8, 3A9, and 3AC). Figure 8-2 shows the active and inactive data lines when scaled vertically. Unscaled Un Line n SAV EAV Line n+1 SAV EAV Line n+2 SAV EAV Line n+3 SAV EAV Line n+4 SAV EAV Line n+5 SAV EAV Line n+6 SAV EAV Line n+7 SAV EAV Scaled Line n SAV EAV Line n+1 SAV EAV Line n+3 SAV EAV Line n+4 SAV EAV Line n+6 SAV EAV Line n+7 SAV EAV Line n+2 Line n+5 Figure 8-2. Unscaled and Scaled Vertical Data Formatting 80 Scaler Configuration Copyright © 2007–2010, Texas Instruments Incorporated Submit Documentation Feedback Product Folder Link(s): TVP5154A TVP5154A www.ti.com 8.4 SLES214C – DECEMBER 2007 – REVISED SEPTEMBER 2010 Field Interleaving In systems where either there are insufficient video ports on the back end processor to accommodate both scaled and unscaled video streams, or where the back end processor does not have sufficient processing power to perform compression on the unscaled image at the same time as other video processing, such as composting of scaled images for display, it is possible to configure the TVP5154A to output different image types on consecutive fields. In this configuration, the field rates for each of the scaled and unscaled images is reduced to accommodate the interleaving of fields, while maintaining a 27-MHz pixel clock. This is useful in video recording systems that are required to display a scaled image but still wish to compress and store full resolution images, albeit at reduced field rates. Field interleaving can generate a sequence of up to 16 fields, where each field can be either unscaled, scaled, or blank. 8.4.1 Registers The field loop count register controls how many fields are in the sequence. The field mode registers control the output field type for each field. Figure 8-3 shows how to configure field interleaving for a sequence of five fields where the first field is unscaled, the second field is scaled, the third field is blank, the fourth field is scaled, and the fifth field is blank. Field 0 Field 1 Field 2 Field 3 Field 4 Field 0 Field 1 Figure 8-3. Field Interleaving Various additional registers exist to configure how the TVP5154A indicates to the back-end processor the state of the current field. The Output Control register 1Fh allows the scaled/unscaled status to be indicated by the upper bit of the SAV/EAV codes. The Output Control register 1Fh also allows the scaled/unscaled status to be indicated by the DID codes of ancillary data. Scaler Configuration Copyright © 2007–2010, Texas Instruments Incorporated Submit Documentation Feedback Product Folder Link(s): TVP5154A 81 TVP5154A SLES214C – DECEMBER 2007 – REVISED SEPTEMBER 2010 www.ti.com 9 Electrical Specifications Absolute Maximum Ratings (1) 9.1 over operating free-air temperature range (unless otherwise noted) VALUE Supply voltage range IOVDD to DGND –0.5 to 3.6 DVDD to DGND –0.5 to 2 PLL_AVDD to PLL_AGND –0.5 to 2 AVDD to AGND –0.5 to 2 –0.5 to 3.6 V Input voltage range, XIN to PLL_GND –0.5 to 2 V –0.2 to 2 V –0.5 to 3.6 V Digital output voltage range, VO to DGND Commercial Operating free-air temperature range Tstg (1) V Digital input voltage range, VI to DGND Analog input voltage range, AI to AGND TA UNIT 0 to 70 Industrial °C –40 to 85 Storage temperature range –65 to 150 °C Stresses beyond those listed under absolute maximum ratings may cause permanent damage to the device. These are stress ratings only and functional operation of the device at these or any other conditions beyond those indicated under recommended operating conditions is not implied. Exposure to absolute-maximum-rated conditions for extended periods may affect device reliability. 9.2 Recommended Operating Conditions MIN NOM MAX 3.0 3.3 3.6 V Digital supply voltage 1.65 1.8 1.95 V Analog PLL supply voltage 1.65 1.8 1.95 V AVDD Analog core supply voltage 1.65 1.8 1.95 V VI(P–P) Analog input voltage (ac-coupling necessary) 0.75 V VIH Digital input voltage high VIL Digital input voltage low VIH_XIN XIN input voltage high VIL_XIN XIN input voltage low IOH High-level output current 2 4 mA IOL Low-level output current –2 –4 mA IOH_CLK CLK high-level output current 4 8 mA IOL_CLK CLK low-level output current –4 –8 IOVDD Digital I/O supply voltage DVDD PLL_AVDD TA 9.3 0 0.7 IOVDD V 0.3 IOVDD 0.7 PLL_AVDD Operating free-air temperature Industrial mA 0 70 –40 85 MIN Frequency Δf Frequency tolerance (1) 82 V °C Reference Clock Specifications f (1) V V 0.3 PLL_AVDD Commercial UNIT NOM MAX 14.31818 –50 UNIT MHz +50 ppm Specified by design Electrical Specifications Copyright © 2007–2010, Texas Instruments Incorporated Submit Documentation Feedback Product Folder Link(s): TVP5154A TVP5154A www.ti.com 9.4 SLES214C – DECEMBER 2007 – REVISED SEPTEMBER 2010 Electrical Characteristics For typical values: Nominal conditions, TA = 25°C For minimum/maximum values: Over recommended operating conditions (unless otherwise noted) TEST CONDITIONS (1) PARAMETER MIN TYP MAX UNIT DC IDD(IO_D) IDD(D) Color bar input (2) 46 52 mA I/O digital supply current at 54 MHz Color bar input (2) 84 90 mA Digital supply current Color bar input (2) 154 174 mA Color bar input (2) 20 29 mA I/O digital supply current at 27 MHz IDD(PLL_A) Analog PLL supply current IDD(A) Analog core supply current Color bar input (2) 134 168 mA PTOT Total power dissipation, normal mode at 27 MHz Color bar input (2) 706 910 mW Total power dissipation, normal mode at 54 MHz Color bar input (2) 832 1050 mW Ci Input capacitance (3) 10 VOH Output voltage high IOH = 2 mA VOL Output voltage low IOL = –2 mA VOH_CLK CLK output voltage high IOH = 4 mA VOL_CLK CLK output voltage low IOL = –4 mA IIH High-level input current IIL Low-level input current 0.8 IOVDD pF V 0.22 IOVDD 0.8 IOVDD V V 0.22 IOVDD V VI = VIH ±22 µA VI = VIL ±22 µA Analog Processing and ADCs (at FS = 30 MSPS) Zi Input impedance, analog video inputs By design Ci Input capacitance, analog video inputs By design (4) 500 kΩ 10 Input voltage range DG Gain control minimum 0 dB DG Gain control maximum 12 dB DNL DC differential nonlinearity A/D only ±0.5 ±1 LSB INL DC integral nonlinearity A/D only ±1 ±2.5 LSB Fr Frequency response 6 MHz –0.9 –3 SNR Signal-to-noise ratio 1 MHz, 0.5 VP-P 48 NS Noise spectrum 50% flat field 48 50 dB DP Differential phase (5) Modulated ramp 1.5 deg DG Differential gain (5) Modulated ramp 0.5 % (1) (2) (3) (4) (5) 0 0.75 pF VI(pp) (5) Ccoupling = 0.1 µF 200 50 V dB dB Measured with a load of 15 pF. For typical measurements only Specified by design The 0.75-V maximum applies to the sync-chroma amplitude, not sync-white. The recommended termination resistors are 37.4 Ω. Specified by design Electrical Specifications Copyright © 2007–2010, Texas Instruments Incorporated Submit Documentation Feedback Product Folder Link(s): TVP5154A 83 TVP5154A SLES214C – DECEMBER 2007 – REVISED SEPTEMBER 2010 9.5 www.ti.com Timing Requirements TEST CONDITIONS (1) PARAMETER MIN Duty cycle SCL TYP MAX 50 UNIT % t1 CLK high time (at 27 MHz) 13.5 t2 CLK low time (at 27 MHz) 13.5 t3 CLK fall time (at 27 MHz) 90% to 10% t4 CLK rise time (at 27 MHz) 10% to 90% t5 Output hold time t6 Output delay time t7 Output hold time t8 Output delay time t9 Data period t10 Output hold time t11 Output delay time t12 Data period t13 CLK high time (at 54 MHz) t14 CLK low time (at 54 MHz) t15 CLK fall time (at 54 MHz) 90% to 10% 6 ns t16 CLK rise time (at 54 MHz) 10% to 90% 6 ns (1) ns ns 5 ns 5 ns 10 ns 25 4 ns ns 16.5 18.5 ns ns 4 ns 16.5 18.5 ns ns 3 ns 3 ns Measured with a load of 15 pF for 27-MHz signals, 25 pF for 54-MHz signals. Specified by design. t1 t2 Negative edge clock Positive edge clock t3 t4 Data 1 Y/C & Syncs Data 2 t5 t6 Figure 9-1. Output Modes 0 and 1: Clocks, Video Data, and Sync t1 t2 SCLK CLK t3 Y/C & Syncs Unscaled Data 1 t4 Scaled Data 1 Unscaled Data 2 Scaled Data 2 t7 t8 t9 t9 Figure 9-2. Output Mode 2: Clocks, Video Data, and Sync 84 Electrical Specifications Copyright © 2007–2010, Texas Instruments Incorporated Submit Documentation Feedback Product Folder Link(s): TVP5154A TVP5154A www.ti.com SLES214C – DECEMBER 2007 – REVISED SEPTEMBER 2010 t13 t14 CLK t15 Y/C & Syncs t16 Scaled Data 1 Unscaled Data 1 Unscaled Data 2 Scaled Data 2 t10 t11 t12 t12 Figure 9-3. Output Mode 3: Clock, Video Data, and Sync (Positive Edge Clock) I2C Host Port Timing 9.6 PARAMETER TEST CONDITIONS MIN MAX UNIT t1 Bus free time, between STOP and START 1.3 µs t2 Setup time, (repeated) START condition 0.6 µs t3 Hold time, (repeated) START condition 0.6 µs t4 Setup time, STOP condition 0.6 ns t5 Data setup time 100 t6 Data hold time t7 Rise time, VC1(SDA) and VC0(SCL) signal t8 Fall time, VC1(SDA) and VC0(SCL) signal Cb Capacitive load for each bus line fI2C I2C clock frequency 0 µs Specified by design 250 ns Specified by design 250 ns Specified by design 400 pF 400 kHz Stop Start VC1 (SDA) ns 0.9 Stop Data t1 t3 t7 t3 t5 t6 t4 t2 t8 VC0 (SCL) Figure 9-4. I2C Host Port Timing 9.7 Thermal Specifications TEST CONDITIONS (1) PARAMETER MIN TYP MAX UNIT qJA Junction-to-ambient thermal resistance, still air Thermal pad soldered to 4-layer High-K PCB 17.17 °C/W qJC Junction-to-case thermal resistance, still air Thermal pad soldered to 4-layer High-K PCB 0.12 °C/W TJ(MAX) Maximum junction temperature for reliable operation (1) 105 °C The exposed thermal pad must be soldered to a JEDEC High-K PCB with adequate ground plane. Electrical Specifications Copyright © 2007–2010, Texas Instruments Incorporated Submit Documentation Feedback Product Folder Link(s): TVP5154A 85 A B C 0.1uF C 0.1uF 1 37.4 R 37.4 R 37.4 R 37.4 R R 37.4 R 37.4 R 37.4 R 37.4 CH4_A CH3_A CH2_A CH1_A CH4_B IN CH3_B IN CH2_B IN CH1_B IN C 0.1uF C 0.1uF I2CA0 R 10k 2 R 10k IOVDD I2CA1 R 10k 2 R 10k IOVDD 2-3 Base Addr 0xB8 - Default I2C ADDRESS SELECTION CH4_A IN CH3_A IN CH2_A IN CH1_A IN REMEMBER 75ohm TERMINATION FOR 0-0.75V INPUT RANGE 1 3 C C 0.1uF INPUT V DIVIDER NETWORK C 0.1uF C 0.1uF DVDD 1 3 D C 0.1uF PLL_VDD 37.4 R 37.4 R 37.4 R 37.4 R C 0.1uF C 0.1uF 2 R 37.4 R 37.4 R 37.4 R 37.4 CH4_B CH3_B CH2_B CH1_B C 0.1uF C 0.1uF TMS R 10k R 100 IOVDD 0.1uF C CH1_B 0.1uF C 0.1uF C CH3_B 0.1uF 0.1uF C C CH4_A CH4_B REFM4 REFP4 0.1uF C CH3_A REFM3 REFP3 0.1uF C CH2_A CH2_B REFM2 REFP2 0.1uF C CH1_A C 1uF PLL_VDD AVDD REFM1 1uF C 3 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 3 C 1uF TVP5154PNP AI1GND AI1A AI1B PLL_VDD PLL_GND REFM2 REFP2 AVDD AGND AI2GND AI2A AI2B PLL_VDD PLL_GND AVDD AGND REFM3 REFP3 AVDD AGND AI3GND AI3A AI3B PLL_VDD PLL_GND REFM4 REFP4 AVDD AGND AI4GND AI4A AI4B U1 XIN/OSC CL1 = CL2 = 2CL – CSTRAY CL1 R 100k Y4 14.31818MHz C 1uF TMS 2 CL2 1uF C REFP2 IOVDD DVDD IOVDD C 1uF C 1uF 1uF C REFP3 AVDD REFP1 XOUT REFP1 REFM1 XIN/OSC XOUT PDN /RESET SCL SDA I2CA0 I2CA1 4 C 1uF 4 C 1uF IOGND VSYNC1/PALI1 FID1/GLCO1 CH2OUT0 CH2OUT1 CH2OUT2 CH2OUT3 CH2OUT4 CH2OUT5 CH2OUT6 CH2OUT7 SCLK2 CLK2 INTREQ2/GPCL2/VBLK2 DGND DVDD IOVDD IOGND AVID2 HSYNC2 VSYNC2/PALI2 FID2/GLCO2 CH3OUT0 CH3OUT1 CH3OUT2 CH3OUT3 CH3OUT4 CH3OUT5 CH3OUT6 CH3OUT7 DGND DVDD 128 127 126 125 124 123 122 121 120 119 118 117 116 115 114 113 112 111 110 109 108 107 106 105 104 103 102 101 100 99 98 97 AGND AVDD REFP1 REFM1 XIN/OSC XOUT PDN RESETB SCL SDA I2CA0 I2CA1 DGND DVDD IOVDD IOGND CH1OUT0 CH1OUT1 CH1OUT2 CH1OUT3 CH1OUT4 CH1OUT5 CH1OUT6 CH1OUT7 SCLK1 CLK1 INTREQ1/GPCL1/VBLK1 AVID1 HSYNC1 DGND DVDD IODVDD PLL_VDD PLL_GND AGND TMS FID4/GLCO4 VSYNC4/PALI4 HSYNC4 AVID4 INTREQ4/GPCL4/VBLK4 CLK4 SCLK4 IOGND IOVDD DVDD DGND CH4OUT7 CH4OUT6 CH4OUT5 CH4OUT4 CH4OUT3 CH4OUT2 CH4OUT1 CH4OUT0 FID3/GLCO3 VSYNC3/PALI3 HSYNC3 AVID3 INTREQ3/GPCL3/VBLK3 CLK3 SCLK3 IOGND IOVDD 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 REFM2 Submit Documentation Feedback Product Folder Link(s): TVP5154A REFM3 Schematic REFM4 86 1uF C 96 95 94 93 92 91 90 89 88 87 86 85 84 83 82 81 80 79 78 77 76 75 74 73 72 71 70 69 68 67 66 65 REFP4 1 C 1uF CH4_D0 CH4_D1 CH4_D2 CH4_D3 CH4_D4 CH4_D5 CH4_D6 CH4_D7 CH3_D0 CH3_D1 CH3_D2 CH3_D3 CH3_D4 CH3_D5 CH3_D6 CH3_D7 CH2_D0 CH2_D1 CH2_D2 CH2_D3 CH2_D4 CH2_D5 CH2_D6 CH2_D7 CH1_D0 CH1_D1 CH1_D2 CH1_D3 CH1_D4 CH1_D5 CH1_D6 CH1_D7 SCLK4 CLK4 GPCL4/VBLK4 AVID4 HSYNC4 VSYNC4/PALI4 FID4/GLCO4 SCLK3 CLK3 GPCL3/VBLK3 AVID3 HSYNC3 VSYNC3/PALI3 FID3/GLCO3 AVID2 HSYNC2 VSYNC2/PALI2 FID2/GLCO2 SCLK2 CLK2 GPCL2/VBLK2 SCLK1 CLK1 GPCL1/VBLK1 AVID1 HSYNC1 VSYNC1/PALI1 FID1/GLCO1 5 5 Scale Size C FCSM No. TVP5154 TEXAS INSTRUMENTS, INC. 12500 TI BLVD DALLAS, TEXAS 75243 RPACK8-33 Sheet /RESET SDA SCL SCK4 CK4 VB4 AV4 HS4 VS4 FID4 RPACK8-33 CH4_OUT0 CH4_OUT1 CH4_OUT2 CH4_OUT3 CH4_OUT4 CH4_OUT5 CH4_OUT6 CH4_OUT7 RPACK8-33 SCK3 CK3 VB3 AV3 HS3 VS3 FID3 RPACK8-33 CH3_OUT0 CH3_OUT1 CH3_OUT2 CH3_OUT3 CH3_OUT4 CH3_OUT5 CH3_OUT6 CH3_OUT7 RPACK8-33 SCK2 CK2 VB2 AV2 HS2 VS2 FID2 RPACK8-33 CH2_OUT0 CH2_OUT1 CH2_OUT2 CH2_OUT3 CH2_OUT4 CH2_OUT5 CH2_OUT6 CH2_OUT7 RPACK8-33 SCK1 CK1 VB1 AV1 HS1 VS1 FID1 RPACK8-33 CH1_OUT0 CH1_OUT1 CH1_OUT2 CH1_OUT3 CH1_OUT4 CH1_OUT5 CH1_OUT6 CH1_OUT7 DWG No. SCLK4 CLK4 GPCL4/VBLK4 AVID4 HSYNC4 VSYNC4/PALI4 FID4/GLCO4 CH4_D0 CH4_D1 CH4_D2 CH4_D3 CH4_D4 CH4_D5 CH4_D6 CH4_D7 SCLK3 CLK3 GPCL3/VBLK3 AVID3 HSYNC3 VSYNC3/PALI3 FID3/GLCO3 CH3_D0 CH3_D1 CH3_D2 CH3_D3 CH3_D4 CH3_D5 CH3_D6 CH3_D7 SCLK2 CLK2 GPCL2/VBLK2 AVID2 HSYNC2 VSYNC2/PALI2 FID2/GLCO2 CH2_D0 CH2_D1 CH2_D2 CH2_D3 CH2_D4 CH2_D5 CH2_D6 CH2_D7 SCLK1 CLK1 GPCL1/VBLK1 AVID1 HSYNC1 VSYNC1/PALI1 FID1/GLCO1 CH1_D0 CH1_D1 CH1_D2 CH1_D3 CH1_D4 CH1_D5 CH1_D6 CH1_D7 Rev 1 CH4_OUT[7..0] CH3_OUT[7..0] CH2_OUT[7..0] CH1_OUT[7..0] A B C D SLES214C – DECEMBER 2007 – REVISED SEPTEMBER 2010 6 2 of 17 /RESET SDA SCL SCK4 CK4 VB4 AV4 HS4 VS4 FID4 CH4_OUT[7..0] SCK3 CK3 VB3 AV3 HS3 VS3 FID3 CH3_OUT[7..0] SCK2 CK2 VB2 AV2 HS2 VS2 FID2 CH2_OUT[7..0] SCK1 CK1 VB1 AV1 HS1 VS1 FID1 CH1_OUT[7..0] 6 TVP5154A www.ti.com 10 Schematic Copyright © 2007–2010, Texas Instruments Incorporated TVP5154A www.ti.com SLES214C – DECEMBER 2007 – REVISED SEPTEMBER 2010 11 Revision History Table 11-1. Revision History REVISION COMMENTS SLES214 Initial release SLES214A Industrial temperature devices added SLES214B Section 1.1, NTSC-J and PAL-Nc support added to feature list. Section 1.2, Application list modified. Section 1.4, Related Products modified. Section 1.5, Trademarks added. Section 1.6, Document conventions added. Section 2, Figure 2-1, Block diagram modified. Section 3.2, I/O type modified for ground pins. Section 4.3, Figure 4-1, Chroma trap filter characteristics for NTSC added. Section 4.3, Figure 4-2, Chroma trap filter characteristics for PAL added. Section 4.4, Figure 4-3, Color low-pass filter characteristics added. Section 4.8, Table 4-1, CGMS-A and Gemstar 2x support added. Section 4.11, Table 4-3, NTSC-J and PAL-Nc support added. Lines per frame and color subcarrier frequency columns also added. Section 6, Figure 6.1, Crystal parallel resistor recommendation added. Section 7.3, Reset and power down information added. Section 8.1, Table 8-1, CGMS-A support added to address 94h-99h. Gemstar 2x support added to address 9Ah-A6h. Section 8.2.2, Automatic offset control description removed. Section 8.2.3, Changed white peak to composite peak. Recommendations added. Section 8.2.10, Brightness control register description modified. Section 8.2.11, Color saturation control register description modified. Section 8.2.13, Contrast control register description modified. Section 8.2.34, NTSC-J support added. Section 8.2.39, Reference to ITU-R BT.656-5 standard added. Section 8.2.50, Status Register #3 description modified. Section 8.2.52, Table 8-10, NTSC-J and PAL-Nc support added. Section 8.2.54, CGMS-A support added. Section 8.2.63, Recommended VBI Configuration RAM settings modifications. Gemstar support included. Section 8.2.64, CGMS-A and Gemstar 2x support added. Section 8.2.72, CGMS-A and Gemstar 2x support added. Section 10.1, Units for temperature corrected. Section 10.2, Units for temperature corrected. Section 10.3, Table formatting modified. Made minor editorial changes (throughout). SLES214C Changed order of some sections in chapters 1, 2, and 3 Section 3.6, Modified when color killer suppresses chrominance processing. Section 9.7, Added thermal specifications. Section 7.2.31, Added Indirect Register Data Section 7.2.32, Added Indirect Register Address Section 7.2.33, Added Indirect Register Read/Write Strobe Section 7.2.44, Added Patch Write Address Section 7.2.45, Added Patch Code Execute Section 7.2.58, Added Patch Read Address Revision History Copyright © 2007–2010, Texas Instruments Incorporated Submit Documentation Feedback Product Folder Link(s): TVP5154A 87 PACKAGE OPTION ADDENDUM www.ti.com 11-Oct-2010 PACKAGING INFORMATION Orderable Device Status (1) Package Type Package Drawing Pins Package Qty Eco Plan (2) Lead/ Ball Finish MSL Peak Temp (3) Samples (Requires Login) TVP5154AIPNP ACTIVE HTQFP PNP 128 90 Green (RoHS & no Sb/Br) CU NIPDAU Level-3-260C-168 HR Request Free Samples TVP5154AIPNPR ACTIVE HTQFP PNP 128 1000 Green (RoHS & no Sb/Br) CU NIPDAU Level-3-260C-168 HR Purchase Samples TVP5154APNP ACTIVE HTQFP PNP 128 90 Green (RoHS & no Sb/Br) CU NIPDAU Level-3-260C-168 HR Purchase Samples TVP5154APNPR ACTIVE HTQFP PNP 128 1000 Green (RoHS & no Sb/Br) CU NIPDAU Level-3-260C-168 HR Request Free Samples (1) The marketing status values are defined as follows: ACTIVE: Product device recommended for new designs. LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect. NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in a new design. PREVIEW: Device has been announced but is not in production. Samples may or may not be available. OBSOLETE: TI has discontinued the production of the device. (2) Eco Plan - The planned eco-friendly classification: Pb-Free (RoHS), Pb-Free (RoHS Exempt), or Green (RoHS & no Sb/Br) - please check http://www.ti.com/productcontent for the latest availability information and additional product content details. TBD: The Pb-Free/Green conversion plan has not been defined. Pb-Free (RoHS): TI's terms "Lead-Free" or "Pb-Free" mean semiconductor products that are compatible with the current RoHS requirements for all 6 substances, including the requirement that lead not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered at high temperatures, TI Pb-Free products are suitable for use in specified lead-free processes. Pb-Free (RoHS Exempt): This component has a RoHS exemption for either 1) lead-based flip-chip solder bumps used between the die and package, or 2) lead-based die adhesive used between the die and leadframe. The component is otherwise considered Pb-Free (RoHS compatible) as defined above. Green (RoHS & no Sb/Br): TI defines "Green" to mean Pb-Free (RoHS compatible), and free of Bromine (Br) and Antimony (Sb) based flame retardants (Br or Sb do not exceed 0.1% by weight in homogeneous material) (3) MSL, Peak Temp. -- The Moisture Sensitivity Level rating according to the JEDEC industry standard classifications, and peak solder temperature. Important Information and Disclaimer:The information provided on this page represents TI's knowledge and belief as of the date that it is provided. TI bases its knowledge and belief on information provided by third parties, and makes no representation or warranty as to the accuracy of such information. Efforts are underway to better integrate information from third parties. TI has taken and continues to take reasonable steps to provide representative and accurate information but may not have conducted destructive testing or chemical analysis on incoming materials and chemicals. TI and TI suppliers consider certain information to be proprietary, and thus CAS numbers and other limited information may not be available for release. In no event shall TI's liability arising out of such information exceed the total purchase price of the TI part(s) at issue in this document sold by TI to Customer on an annual basis. Addendum-Page 1 IMPORTANT NOTICE Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, modifications, enhancements, improvements, and other changes to its products and services at any time and to discontinue any product or service without notice. Customers should obtain the latest relevant information before placing orders and should verify that such information is current and complete. All products are sold subject to TI’s terms and conditions of sale supplied at the time of order acknowledgment. TI warrants performance of its hardware products to the specifications applicable at the time of sale in accordance with TI’s standard warranty. Testing and other quality control techniques are used to the extent TI deems necessary to support this warranty. Except where mandated by government requirements, testing of all parameters of each product is not necessarily performed. TI assumes no liability for applications assistance or customer product design. Customers are responsible for their products and applications using TI components. To minimize the risks associated with customer products and applications, customers should provide adequate design and operating safeguards. TI does not warrant or represent that any license, either express or implied, is granted under any TI patent right, copyright, mask work right, or other TI intellectual property right relating to any combination, machine, or process in which TI products or services are used. Information published by TI regarding third-party products or services does not constitute a license from TI to use such products or services or a warranty or endorsement thereof. Use of such information may require a license from a third party under the patents or other intellectual property of the third party, or a license from TI under the patents or other intellectual property of TI. Reproduction of TI information in TI data books or data sheets is permissible only if reproduction is without alteration and is accompanied by all associated warranties, conditions, limitations, and notices. Reproduction of this information with alteration is an unfair and deceptive business practice. TI is not responsible or liable for such altered documentation. Information of third parties may be subject to additional restrictions. Resale of TI products or services with statements different from or beyond the parameters stated by TI for that product or service voids all express and any implied warranties for the associated TI product or service and is an unfair and deceptive business practice. TI is not responsible or liable for any such statements. TI products are not authorized for use in safety-critical applications (such as life support) where a failure of the TI product would reasonably be expected to cause severe personal injury or death, unless officers of the parties have executed an agreement specifically governing such use. Buyers represent that they have all necessary expertise in the safety and regulatory ramifications of their applications, and acknowledge and agree that they are solely responsible for all legal, regulatory and safety-related requirements concerning their products and any use of TI products in such safety-critical applications, notwithstanding any applications-related information or support that may be provided by TI. Further, Buyers must fully indemnify TI and its representatives against any damages arising out of the use of TI products in such safety-critical applications. TI products are neither designed nor intended for use in military/aerospace applications or environments unless the TI products are specifically designated by TI as military-grade or "enhanced plastic." Only products designated by TI as military-grade meet military specifications. Buyers acknowledge and agree that any such use of TI products which TI has not designated as military-grade is solely at the Buyer's risk, and that they are solely responsible for compliance with all legal and regulatory requirements in connection with such use. TI products are neither designed nor intended for use in automotive applications or environments unless the specific TI products are designated by TI as compliant with ISO/TS 16949 requirements. Buyers acknowledge and agree that, if they use any non-designated products in automotive applications, TI will not be responsible for any failure to meet such requirements. Following are URLs where you can obtain information on other Texas Instruments products and application solutions: Products Applications Audio www.ti.com/audio Communications and Telecom www.ti.com/communications Amplifiers amplifier.ti.com Computers and Peripherals www.ti.com/computers Data Converters dataconverter.ti.com Consumer Electronics www.ti.com/consumer-apps DLP® Products www.dlp.com Energy and Lighting www.ti.com/energy DSP dsp.ti.com Industrial www.ti.com/industrial Clocks and Timers www.ti.com/clocks Medical www.ti.com/medical Interface interface.ti.com Security www.ti.com/security Logic logic.ti.com Space, Avionics and Defense www.ti.com/space-avionics-defense Power Mgmt power.ti.com Transportation and Automotive www.ti.com/automotive Microcontrollers microcontroller.ti.com Video and Imaging RFID www.ti-rfid.com OMAP Mobile Processors www.ti.com/omap Wireless Connectivity www.ti.com/wirelessconnectivity TI E2E Community Home Page www.ti.com/video e2e.ti.com Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265 Copyright © 2011, Texas Instruments Incorporated