STM6502, STM6503
STM6504, STM6505
Dual push-button Smart ResetTM with user-adjustable setup delays
Features
■
Dual Smart Reset push-button inputs with
extended reset setup delay
■
Adjustable Smart Reset setup delay (tSRC):
by external capacitor or three-state logic
(product options): tSRC = 2, 6, 10 s (min.)
■
Power-on reset
■
Single RST output, active-low, open-drain
■
Factory-programmable thresholds to monitor
VCC in the range of 1.575 to 4.625 V typ.
■
Operating voltage 1.0 V (active-low output
valid) to 5.5 V
TDFN8 (DG)
2 mm x 2 mm
Applications
■
Mobile phones, smartphones
■
Low supply current
■
e-books
■
Operating temperature:
industrial grade –40 °C to +85 °C
■
MP3 players
■
Games
■
Portable navigation devices
■
Any application that requires delayed reset
push-button(s) response for improved system
stability
■
TDFN8 package: 2 mm x 2 mm x 0.75 mm
■
RoHS compliant
Table 1.
Device summary
Voltage inputs
Smart Reset inputs
Part
number
VCC
VBAT
SR0
SR1
STM6502(1)
✓
✓
✓
STM6503
✓
✓
✓
STM6504(1)
✓
✓
STM6505
✓
✓
✓
tSRC
programming
SRE
Ext.
immediate,
SRC pin
independent
Threestate
input
✓
✓
Package
RST
BLD
TSR
✓
✓
Reset or Power
Good outputs
✓
TDFN-8L
✓
✓
TDFN-8L
✓
✓
TDFN-8L
✓
✓
TDFN-8L
1. Contact local ST sales office for availability.
June 2010
Doc ID 16101 Rev 5
1/29
www.st.com
1
Contents
STM6502, STM6503, STM6504, STM6505
Contents
1
Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
1.1
Smart Reset devices . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
1.2
Pin descriptions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
1.2.1
Power supply (VCC) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
1.2.2
Ground (VSS) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
1.2.3
Primary Smart Reset input (SR0) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
1.2.4
Secondary Smart Reset input (SR1) . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
1.2.5
Edge-triggered Smart Reset input (SRE pin) – STM6504 only . . . . . . . 11
1.2.6
Adjustable delay of Smart Reset input (SRC pin) – STM6502
and STM6505 only . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
1.2.7
Programmable Smart Reset input delay (TSR pin) – STM6503
and STM6504 only . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
1.2.8
Reset output (RST) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
1.2.9
Battery monitoring input (VBAT) – STM6505 only . . . . . . . . . . . . . . . . . 12
1.2.10
Battery low detect output (BLD) – STM6505 only . . . . . . . . . . . . . . . . . 12
2
Typical operating characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
3
Maximum ratings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
4
DC and AC parameters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
5
Package mechanical data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
6
Part numbering . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26
7
Package marking . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27
8
Revision history . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28
2/29
Doc ID 16101 Rev 5
STM6502, STM6503, STM6504, STM6505
List of tables
List of tables
Table 1.
Table 2.
Table 3.
Table 4.
Table 5.
Table 6.
Table 7.
Table 8.
Table 9.
Table 10.
Table 11.
Table 12.
Table 13.
Table 14.
Device summary . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
Signal names . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
tSRC programmed by an ideal external capacitor – STM6502 and STM6505 . . . . . . . . . . 11
Absolute maximum ratings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
Operating and measurement conditions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
DC and AC characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
VCC voltage thresholds . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
TDFN – 8-lead 2 x 2 x 0.75 mm, 0.5 mm pitch package mechanical data . . . . . . . . . . . . . 21
Parameter for landing pattern - TDFN – 8-lead 2 x 2 mm package . . . . . . . . . . . . . . . . . . 22
Carrier tape dimensions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
Reel dimensions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
Ordering information scheme . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26
Package marking . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27
Document revision history . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28
Doc ID 16101 Rev 5
3/29
STM6502, STM6503, STM6504, STM6505
List of figures
List of figures
Figure 1.
Figure 2.
Figure 3.
Figure 4.
Figure 5.
Figure 6.
Figure 7.
Figure 8.
Figure 9.
Figure 10.
Figure 11.
Figure 12.
Figure 13.
Figure 14.
Figure 15.
Figure 16.
Figure 17.
Figure 18.
Figure 19.
Figure 20.
Figure 21.
Logic diagrams . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
Pin connections . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
Block diagram - STM6502, STM6503, STM6504 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
Block diagram - STM6505 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
Single-button Smart Reset typical hookup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Dual-button Smart Reset typical hookup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
STM6502, STM6503 timing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
STM6504 timing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
STM6505 timing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
Supply current (ICC) vs. temperature (STM6505) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
Smart Reset delay (tSRC) vs. temperature, CSRC = 0.62 µF (STM6505) . . . . . . . . . . . . . . 13
Reset threshold (VRST) vs. temperature, “S” threshold option, VCC falling (STM6505) . . . 14
VBAT monitoring threshold (VBATTH) vs. temperature, falling (STM6505) . . . . . . . . . . . . . . 14
AC testing input/output waveforms . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
TDFN – 8-lead 2 x 2 x 0.75 mm, 0.5 mm pitch package outline . . . . . . . . . . . . . . . . . . . . . 21
Landing pattern - TDFN – 8-lead 2 x 2 mm without thermal pad . . . . . . . . . . . . . . . . . . . . 22
Carrier tape . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
Reel dimensions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
Tape trailer/leader. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25
Pin 1 orientation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25
Package marking, top view . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27
Doc ID 16101 Rev 5
4/29
STM6502, STM6503, STM6504, STM6505
1
Description
Description
STM6502 has two combined Smart Reset inputs (SR0 and SR1) with delayed Smart Reset
setup time (tSRC) programmed by an external capacitor on the SRC pin.
STM6503 is similar to STM6502, has two combined delayed Smart Reset inputs (SR0, SR1)
and three user-selectable delayed Smart Reset setup time (tSRC) options of 2 s, 6 s and
10 s through a three-state TSR input pin: when connected to ground, tSRC = 2 s; when left
open, tSRC = 6 s; when connected to VCC, tSRC = 10 s (all the times are minimum).
STM6504 has two independent Smart Reset inputs. SR0 provides the delayed Smart Reset
setup time (tSRC) function with three user-selectable tSRC options through a three-state TSR
input pin: when connected to ground, tSRC = 2 s; when left open, tSRC = 6 s; when
connected to VCC, tSRC = 10 s (all the times are minimum). SRE provides instant reset. SRE
is edge-triggered with a special debounce time (tDEBOUNCE = 240 ms min.) at the falling
edge after a valid reset period.
STM6505 has two combined delayed Smart Reset inputs (SR0, SR1) and provides an
adjustable reset delay setup time via an external capacitor connected to the SRC pin.
The RST output depends also on the VCC monitoring threshold. STM6505 also provides
independent low battery detect (BLD) output controlled by the secondary external input
voltage VBAT. VBAT is monitored for low voltage and provides an indication on the battery low
detect output pin (BLD). VBAT threshold is 1.25 V, fixed, and an external resistor divider is to
be used to set the actual battery voltage threshold. VBAT threshold hysteresis is 8 mV typ.
(16 mV max.). VBAT is voltage monitoring input only, the device is powered only from the
VCC pin; VCC must be ≥ 1.575 V for proper operation of the VBAT comparator.
1.1
Smart Reset devices
The Smart Reset device family STM65xx provides a useful feature that ensures inadvertent
short reset push-button closures do not cause system resets. This is done by implementing
extended Smart Reset input delay (tSRC). Once the valid Smart Reset input levels and setup
delay are met, the device generates an output reset pulse with user-programmable timeout
period (tREC).
The Smart Reset inputs can be also connected to the applications interrupt to allow the
control of both the interrupt pin and the hard reset functions. If the push-buttons are closed
for a short time, the processor is only interrupted. If the system still does not respond
properly, holding the push-buttons for the extended setup time (tSRC) causes hard reset of
the processor through the reset outputs. The Smart Reset feature helps significantly
increase system stability.
The STM65xx family of Smart Reset devices consists of low current microprocessor reset
circuits targeted at applications such as MP3 players, navigation, smartphones or mobile
phones; generally any application that requires delayed reset push-button(s) response for
improved system stability. The STM65xx devices feature single or dual Smart Reset inputs
(SR). The delayed Smart Reset setup time (tSRC) options of 2 s, 6 s and 10 s
(all min.) are adjustable by an external capacitor on the SRC pin or selectable by three-state
logic. The delayed setup period ignores switch closures shorter than tSRC, thus preventing
unwanted resets.
Doc ID 16101 Rev 5
5/29
Description
STM6502, STM6503, STM6504, STM6505
The STM65xx devices have active-low (optionally active-high) open-drain reset (RST)
output(s) with or without internal pull-up resistor or push-pull as output options, with factoryprogrammed or capacitor-adjustable or push-buttons defined output reset pulse duration,
with or without power-on reset function.
Some devices also have an undervoltage monitoring feature: the reset output is also
asserted when the monitored supply voltage VCC drops below the specified threshold. The
reset output remains asserted for the reset timeout period (tREC) after the monitored supply
voltage goes above the specified threshold.
Figure 1.
Logic diagrams
VCC
VCC
SR0
SR0
STM6502
SR1
RST
STM6503
SR1
RST
TSR
SRC
VSS
VSS
VCC
VCC
SR0
SR0
STM6504
SRE
RST
RST
SR1
STM6505
SRC
TSR
BLD
VBAT
VSS
VSS
AM00378
Figure 2.
6/29
Pin connections
RST
1
8
VCC
RST
1
8
VCC
VSS
2
7
SR0
VSS
2
7
SR0
SR1
3
6
SRC
SR1
3
6
TSR
NC
4
5
NC
NC
4
5
NC
STM
6502
STM
6503
RST
1
8
VCC
RST
1
8
VCC
VSS
2
7
SR0
VSS
2
7
SR0
SRE
3
6
TSR
SR1
3
6
SRC
NC
4
5
NC
BLD
4
5
VBAT
STM
6504
Doc ID 16101 Rev 5
STM
6505
AM00379
STM6502, STM6503, STM6504, STM6505
Table 2.
Description
Signal names
Symbol
Input/
output
RST
Output
Open-drain reset output, active-low.
BLD
Output
Battery low detect output, active-low, open-drain. STM6505 only.
SR0
Input
Primary push-button Smart Reset input. Active-low, with or without internal
65 kΩ pull-up to VCC (product options).
SR1
Input
Secondary push-button Smart Reset input - combines with the primary pushbutton reset to provide setup delay time before reset. Active-low, with or without
internal 65 kΩ pull-up to VCC (product options).
SRE
Input
Secondary push-button Smart Reset input - provides instant Smart Reset. SRE
is edge-triggered with a special debounce time (tDEBOUNCE = 240 ms min.) at
the falling edge after a valid reset period. Active-high, no internal pull-up to VCC.
STM6504 only.
SRC
Input
Smart Reset input delay setup control: connect to an external capacitor to adjust
the delay setup time (tSRC). STM6502 and STM6505 only.
TSR
Input
A three-state Smart Reset input delay setup control. When connected to
ground, tSRC = 2 s; when left open, tSRC = 6 s; when connected to VCC,
tSRC = 10 s (all times are minimum). TSR is a DC-type input, intended to be
either permanently grounded, permanently connected to VCC or permanently
left open. If left open, for improved system glitch immunity it is strongly
recommended to connect a 0.1 µF decoupling ceramic capacitor between the
TSR and VSS pins. STM6503 and STM6504 only.
VCC
Supply
VBAT
Input
VSS
Supply
NC
Description
Supply voltage input. Power supply for the device and an input for the monitored
supply voltage. A 0.1 µF decoupling ceramic capacitor is recommended to be
connected between the VCC and VSS pins.
Battery voltage monitoring input. STM6505 only.
Ground
No connect (not bonded); should be connected to VSS.
Doc ID 16101 Rev 5
7/29
Description
STM6502, STM6503, STM6504, STM6505
Figure 3.
Block diagram - STM6502, STM6503, STM6504
VCC
SR1
(SRE
STM6504
only)(1)
SR0
SRC (STM6502)
TSR (STM6503,
STM6504)
VRST
COMPARE
Logic
tREC
generator
RST
Logic
AM00352a
1. STM6504 only: SR0 and SRE are working independently. SRE is edge-triggered and has a special
debounce time (tDEBOUNCE = 240 ms min.) at the falling edge after a valid reset period.
Figure 4.
Block diagram - STM6505
6"!4
6##
6"!44(
#/-0!2%
6234
#/-0!2%
",$
T2%#
GENERATOR
6##
234
32
32
,OGIC
32#
!-B
8/29
Doc ID 16101 Rev 5
STM6502, STM6503, STM6504, STM6505
Figure 5.
Description
Single-button Smart Reset typical hookup
6##
6##
2%3%4
234
6##
432
34-
-#5
32
).4
.-)
32
633
633
053("544/.
37)4#(
!-B
Figure 6.
Dual-button Smart Reset typical hookup
6##
6##
234
2%3%4
6##
432
34-
-#5
32
).4
.-)
32
633
053("544/.
37)4#(
633
053("544/.
37)4#(
!-6
Doc ID 16101 Rev 5
9/29
Description
STM6502, STM6503, STM6504, STM6505
1.2
Pin descriptions
1.2.1
Power supply (VCC)
This pin is used to provide the power to the device and to monitor the power supply.
A 0.1 µF decoupling ceramic capacitor is recommended to be connected between the VCC
and VSS pins.
1.2.2
Ground (VSS)
This is the supply ground for the device.
1.2.3
Primary Smart Reset input (SR0)
The primary push-button Smart Reset input, active-low pin is connected to the first pushbutton switch.
1.2.4
Secondary Smart Reset input (SR1)
The secondary push-button Smart Reset input, active-low pin is connected to the second
push-button switch. Keeping both Smart Reset inputs SR0 and SR1 active for longer than
tSRC activates the reset output pulse.
Figure 7.
STM6502, STM6503 timing
tSRC
tREC
SR0
SR1
RST
AM00327
Reset is asserted “low” right after the Smart Reset setup delay (tSRC) has been met and
returns to high after the tREC period.
10/29
Doc ID 16101 Rev 5
STM6502, STM6503, STM6504, STM6505
1.2.5
Description
Edge-triggered Smart Reset input (SRE pin) – STM6504 only
The SRE pin is active-high, immediate and independent reset input that includes an edge
trigger with debounce delay tDEBOUNCE on the falling edge.
Note:
The triggering edge must be a high-to-low or low-to-high transition with a slew-rate faster
than 1 V/µs typ.
Figure 8.
STM6504 timing
t < tDEBOUNCE
=> tREC timer reset
t < tSRC
=> no output response
tSRC
SR0
Independent
SRE
RST
No debounce
tREC
tDEBOUNCE
tREC
(rising edges within
tDEBOUNCE are ignored)
1.2.6
tREC
AM00328V2
Adjustable delay of Smart Reset input (SRC pin) – STM6502 and
STM6505 only
This pin controls the setup time before the push-button action is validated by the reset
output. It is connected to an external capacitor (CSRC), which is tied to ground to provide the
desired value of the setup time (tSRC).
Calculated tSRC and CSRC examples are given in Table 3. Refer also to Table 6.
Table 3.
tSRC programmed by an ideal external capacitor – STM6502 and STM6505
Calculated CSRC
value [µF]
Setup delay tSRC [s](1)(2)
Min.
Typ.
Max.
Closest common
CSRC value [µF]
0.2
2
2.5
3.0
0.22
0.3
3
3.75
4.5
0.33
0.6
6
7.5
9
0.56
1
10
12.5
15
1
1. At 25 °C. Example calculations based on an ideal capacitor. During application design and component
selection it should be considered that the current flowing into the external tSRC programming capacitor
(CSRC) is on the order of 100 nA, therefore a low-leakage capacitor (ceramic or film capacitor) should be
used and placed as close as possible to the SRC pin. Also an adequate low-leakage PCB environment
should be ensured to prevent tSRC accuracy from being affected. A recommended minimum value of CSRC
is 0.01 µF.
2. In case of repeated activations of the tSRC timer, an interval of 10 ms min. is needed between the
activations to fully discharge C SRC, so that the next tSRC is as specified.
Doc ID 16101 Rev 5
11/29
Description
1.2.7
STM6502, STM6503, STM6504, STM6505
Programmable Smart Reset input delay (TSR pin) – STM6503 and
STM6504 only
The TSR pin allows the user to program the setup time before the push-button action is
validated by the reset output. It is controlled by different voltage levels on the three-state
TSR input pin: when connected to ground, tSRC = 2 s; when left open, tSRC = 6 s; when
connected to VCC, tSRC = 10 s (all times are minimum). TSR is a DC-type input, intended to
be either permanently grounded, permanently connected to VCC or permanently left open.
If it is left open, for improved system glitch immunity it is strongly recommended to connect
a 0.1 µF decoupling ceramic capacitor between the TSR and VSS pins.
1.2.8
Reset output (RST)
RST is the active-low, open-drain reset output in the Smart Reset family.
1.2.9
Battery monitoring input (VBAT) – STM6505 only
VBAT is an input for monitoring the battery voltage. VBAT threshold is 1.25 V, fixed, and an
external resistor divider is to be used to set the actual battery voltage threshold.
1.2.10
Battery low detect output (BLD) – STM6505 only
The battery low detect output is controlled by the VBAT voltage monitoring input and is
active-low, open-drain, with no pull-up.
Figure 9.
STM6505 timing
tSRC
tREC
SR0
SR1
RST
VBAT
VBATTH
BLD
AM00329
12/29
Doc ID 16101 Rev 5
STM6502, STM6503, STM6504, STM6505
2
Typical operating characteristics
Typical operating characteristics
Figure 10. Supply current (ICC) vs. temperature (STM6505)
3
2.5
ICC [μA]
2
1.5
1
0.5
0
-60
-40
-20
0
20
40
60
80
100
120
140
Temperature [°C]
5.5 V
2V
5V
3V
AM04886v1
Figure 11. Smart Reset delay (tSRC) vs. temperature, CSRC = 0.62 µF (STM6505)
9.2
8.7
tSRC [s]
8.2
7.7
7.2
6.7
6.2
-60
-40
-20
0
20
40
60
80
100
120
140
Temperature [°C]
5.75 V
5.5 V
3.3 V
Doc ID 16101 Rev 5
AM04887v1
13/29
Typical operating characteristics
STM6502, STM6503, STM6504, STM6505
Figure 12. Reset threshold (VRST) vs. temperature, “S” threshold option, VCC falling (STM6505)
2.99
2.97
VRST [V]
2.95
2.93
2.91
2.89
2.87
2.85
-60
-40
-20
0
20
40
60
80
100
120
140
Temperature [°C]
AM04888v1
Figure 13. VBAT monitoring threshold (VBATTH) vs. temperature, falling (STM6505)
1.275
1.27
1.265
1.26
VBATTH [V]
1.255
1.25
1.245
1.24
1.235
1.23
1.225
-60
-40
-20
0
20
40
60
80
100
120
140
Temperature [°C]
5.75 V
14/29
5.5 V
3.3 V
Doc ID 16101 Rev 5
2V
1.58 V
AM04889v1
STM6502, STM6503, STM6504, STM6505
3
Maximum ratings
Maximum ratings
Stressing the device above the rating listed in Table 4: Absolute maximum ratings may
cause permanent damage to the device. These are stress ratings only and operation of the
device at these or any other conditions above those indicated in the operating sections of
this specification is not implied. Exposure to absolute maximum rating conditions for
extended periods may affect device reliability. Refer also to the STMicroelectronics SURE
Program and other relevant quality documents.
Table 4.
Absolute maximum ratings
Symbol
TSTG
Parameter
Storage temperature (VCC off)
TSLD(1)
Lead solder temperature for 10 seconds
θ JA
Thermal resistance (junction to ambient)
VIO
Input or output voltage
VCC
Supply voltage
TDFN8
Value
Unit
–55 to +150
°C
260
°C
149.0
°C/W
–0.3 to 5.5(2)
V
–0.3 to 7
V
1. Reflow at peak temperature of 260 °C. The time above 255 °C must not exceed 30 seconds.
2. For inputs or outputs with internal pull-up resistors and push-pull type outputs –0.3 to VCC +0.3 V only.
Doc ID 16101 Rev 5
15/29
DC and AC parameters
4
STM6502, STM6503, STM6504, STM6505
DC and AC parameters
This section summarizes the operating measurement conditions, and the DC and AC
characteristics of the device. The parameters in the DC and AC characteristics tables that
follow, are derived from tests performed under the measurement conditions summarized in
Table 5: Operating and measurement conditions. Designers should check that the operating
conditions in their circuit match the operating conditions when relying on the quoted
parameters.
Table 5.
Operating and measurement conditions
Parameter
Value
Unit
VCC supply voltage
1.0 to 5.5
V
Ambient operating temperature (TA)
–40 to +85
°C
≤ 5
ns
Input pulse voltages
0.2 to 0.8 V CC
V
Input and output timing ref. voltages
0.3 to 0.7 V CC
V
Input rise and fall times
Figure 14. AC testing input/output waveforms
16/29
0.8 VCC
0.7 VCC
0.2 VCC
0.3 VCC
Doc ID 16101 Rev 5
AM00478
STM6502, STM6503, STM6504, STM6505
Table 6.
DC and AC characteristics
Symbol
VCC
DC and AC parameters
Test conditions(1)
Parameter
Supply voltage range
Reset output valid - active-low
STM6502
STM6503
(3)
VCC = 5.0 V, TSR left open
VCC = 3.0 V, TSR left open
Supply current (inputs in
their inactive state)
STM6504
STM6505
Unit
5.5
V
µA
1.1
µA
5.8
3
4
(3)
2.3
V(3)
µA
µA
5.8
3
VCC = 5.0 V
VCC = 3.0
Max.
1.2
4
(3)
VCC = 5.0 V, TSR left open
VCC = 3.0 V, TSR left open
Typ.(2)
1.0
VCC = 5.0 V
VCC = 3.0 V
ICC
Min.
µA
µA
3.3
2.2
µA
µA
Output characteristics
VOL
tREC
Reset output voltage low
(reset asserted: RST, BLD)
Reset timeout delay,
factory-programmed
VCC ≥ 4.5 V, sinking 3.2 mA
0.3
V
VCC ≥ 3.3 V, sinking 2.5 mA
0.3
V
VCC ≥ 1.0 V, sinking 0.1 mA
0.3
V
Option A
140
210
280
ms
Option B
240
360
480
ms
–40 to +85 °C
VRST
–2.5%
VRST
VRST
+2.5%
V
25 °C
VRST
–2.0%
VRST
VRST
+2.0%
V
VCC monitoring reset thresholds
VRST
Fixed voltage trip point for
VCC monitoring (refer to
Table 7)
L, M
VHYST
Hysteresis of VRST
VCC to reset delay
0.5%
T, S, R, Z, Y, W, V
1%
VCC falling from
(VRST + 100 mV) to (VRST - 100 mV) at
10 mV/µs(4)
20
µs
VBAT monitoring
VBATTH
Fixed VBAT monitoring
threshold
STM6505 only
VBATHYST
VBATTH hysteresis
STM6505 only
ILI(VBAT)
VBAT input leakage current
STM6505 only
Doc ID 16101 Rev 5
1.225
–100
1.25
1.275
V
8
16
mV
10
100
nA
17/29
DC and AC parameters
Table 6.
STM6502, STM6503, STM6504, STM6505
DC and AC characteristics (continued)
Symbol
Test conditions(1)
Parameter
Min.
Typ.(2)
Max.
Unit
Smart Reset inputs
VIL
SR0, SR1, SRE input
voltage low
VSS
–0.3
0.3
VCC
V
VIH
SR0, SR1, SRE input
voltage high
0.7
VCC
5.5
V
ILI(SR)
Input leakage current, SR
and SRE inputs
Option without internal pull-up resistor
–1
+1
µA
ILI(TSR)
Input leakage current, TSR
input
STM6503 and STM6504 only
–5
+7
µA
RPUI
Internal pull-up resistor,
input (optional - refer to
Table 12)
tDEBOUNCE
SRE input falling edge
debounce time
65
STM6504 only
kΩ
240
360
480
ms
TA = 25 °C
10 x
CSRC
(µF)
12.5 x
CSRC
(µF)
15 x
CSRC
(µF)
s
TSR = VSS
2
2.5
3
s
6
7.5
9
s
10
12.5
15
s
Smart Reset delay
tSRC
(5)
Capacitor-programmable
Smart Reset setup time,
STM6502 and STM6505.
Refer to Table 3.
tSRC
(5)
TSR pin-programmable
Smart Reset setup time,
STM6503 and STM6504.
TSR =
floating(6)
TSR = VCC
1. Valid for ambient operating temperature: TA = –40 to +85 °C; VCC = 1.0 to 5.5 V (except where noted).
2. Typical value is at 25 °C and VCC = 3.3 V unless otherwise noted.
3. For devices with VRST < 3.0 V.
4. Guaranteed by design.
5. Input glitch immunity is equal to tSRC (when both SR inputs are low, otherwise infinite). STM6502, STM6503, STM6505
only.
6. If left open, for improved system glitch immunity it is strongly recommended to connect a 0.1 µF decoupling ceramic
capacitor between the TSR and VSS pins.
18/29
Doc ID 16101 Rev 5
STM6502, STM6503, STM6504, STM6505
.
Table 7.
DC and AC parameters
VCC voltage thresholds
VCC monitoring threshold
VRST
±2.5% (–40 °C to +85 °C)
±2.0% (25 °C)
Typ.
Unit
Min.
Max.
Min.
Max.
L (falling)
4.625
4.509
4.741
4.533
4.718
V
M (falling)
4.375
4.266
4.484
4.288
4.463
V
T (falling)
3.075
2.998
3.152
3.014
3.137
V
S (falling)
2.925
2.852
2.998
2.867
2.984
V
R (falling)
2.625
2.559
2.691
2.573
2.678
V
Z (falling)
2.313
2.255
2.371
2.267
2.359
V
Y (falling)
2.188
2.133
2.243
2.144
2.232
V
W (falling)
1.665
1.623
1.707
1.632
1.698
V
V (falling)
1.575
1.536
1.614
1.544
1.607
V
Doc ID 16101 Rev 5
19/29
Package mechanical data
5
STM6502, STM6503, STM6504, STM6505
Package mechanical data
In order to meet environmental requirements, ST offers these devices in different grades of
ECOPACK® packages, depending on their level of environmental compliance. ECOPACK®
specifications, grade definitions and product status are available at: www.st.com.
ECOPACK® is an ST trademark.
20/29
Doc ID 16101 Rev 5
STM6502, STM6503, STM6504, STM6505
Package mechanical data
Figure 15. TDFN – 8-lead 2 x 2 x 0.75 mm, 0.5 mm pitch package outline
D
A
B
PIN 1 INDEX AREA
E
0.10 C 2x
0.10 C 2x
TOP VIEW
0.10 C
C
A1
A
SEAT ING
PLANE
SIDE VIEW
0.08 C
e
b
PIN 1 INDEX AREA
1
4
0.10
C A B
Pin#1 ID
L
5
8
BOTTOM VIEW
8070540_A
Table 8.
TDFN – 8-lead 2 x 2 x 0.75 mm, 0.5 mm pitch package mechanical data
Dimension (mm)
Dimension (inches)
Symbol
Min.
Nom.
Max.
Min.
Nom.
Max.
A
0.70
0.75
0.80
0.028
0.030
0.031
A1
0.00
0.02
0.05
0.000
0.001
0.002
b
0.15
0.20
0.25
0.006
0.008
0.010
D
BSC
1.9
2.00
2.1
0.075
0.079
0.083
E
BSC
1.9
2.00
2.1
0.075
0.079
0.083
e
L
0.50
0.45
0.55
0.020
0.65
Doc ID 16101 Rev 5
0.018
0.022
0.026
21/29
Package mechanical data
STM6502, STM6503, STM6504, STM6505
Figure 16. Landing pattern - TDFN – 8-lead 2 x 2 mm without thermal pad
D
P
E
E1
L
b
Table 9.
AM00441
Parameter for landing pattern - TDFN – 8-lead 2 x 2 mm package
Dimension (mm)
Parameter
22/29
Description
Min.
Nom.
Max.
L
Contact length
1.05
—
1.15
b
Contact width
0.25
—
0.30
E
Max. land pattern Y-direction
—
2.85
—
E1
Contact gap spacing
—
0.65
—
D
Max. land pattern X-direction
—
1.75
—
P
Contact pitch
—
0.5
—
Doc ID 16101 Rev 5
STM6502, STM6503, STM6504, STM6505
Package mechanical data
Figure 17. Carrier tape
P0
D
P2
T
E
A0
F
Top cover
tape
W
B0
Center lines
of cavity
K0
P1
User direction of feed
AM03073v2
Table 10.
Carrier tape dimensions
Package
W
D
TDFN8
8.00
+0.30
–0.10
1.50
+0.10/
–0.00
E
P0
P2
F
1.75
4.00
2.00
3.50
±0.10 ±0.10 ±0.10 ±0.05
A0
B0
K0
P1
T
2.30
±0.05
2.30
±0.05
1.00
±0.05
4.00
±0.10
0.250
±0.05
Doc ID 16101 Rev 5
Unit
Bulk
qty.
mm 3000
23/29
Package mechanical data
STM6502, STM6503, STM6504, STM6505
Figure 18. Reel dimensions
T
40 mm min.
acces hole
at slot location
B
D
C
N
A
Full radius
Tape slot
in core for
tape start
25 mm min width
G measured
at hub
AM00443
Table 11.
24/29
Reel dimensions
Tape sizes
A max.
B min.
C
D min.
N min.
G
T max.
8 mm
180 (7 inches)
1.50
13.0 +/– 0.20
20.20
60
8.4 +2/–0
14.40
Doc ID 16101 Rev 5
STM6502, STM6503, STM6504, STM6505
Package mechanical data
Figure 19. Tape trailer/leader
End
Top
cover
tape
Start
No components
Components
100 mm min.
T RA IL ER
No components
L EA D ER
160 mm min.
400 mm min.
Sealed with cover tape
User direction of feed
AM00444
Figure 20. Pin 1 orientation
User direction of feed
Note:
1
Drawings are not to scale.
2
All dimensions are in mm, unless otherwise noted.
Doc ID 16101 Rev 5
AM00442
25/29
Part numbering
STM6502, STM6503, STM6504, STM6505
6
Part numbering
Table 12.
Ordering information scheme
Example:
STM6505
W
C
A
B
DG
6
F
Device type
STM6502(1)
STM6503
STM6504(1)
STM6505
Reset (VCC monitoring) threshold voltage
(VRST), typ., falling
L = 4.625 V
S = 2.925 V
R = 2.625 V
Z = 2.313 V
W = 1.665 V
V = 1.575 V
Smart Reset setup delay (tSRC); presence of internal input
pull-up on all Smart Reset inputs (SRx, SRE)
A = user-programmable (external capacitor); no input pull-up
C = user-programmable (external capacitor); 65 kΩ input pull-up
E = 2 or 6 or 10 s min., user-programmable (three-state); no input pull-up
F = 2 or 6 or 10 s min., user-programmable (three-state); 65 kΩ input pull-up
Output type
A = open-drain, no pull-up, active-low
Reset timeout period (tREC)
A = 140 ms min.
B = 240 ms min.
Package
DG = TDFN8 2 x 2 x 0.75 mm, 0.5 mm pitch
Temperature range
6 = –40 °C to +85 °C
Shipping method
F = ECOPACK® package, tape and reel
1. Contact local ST sales office for availability.
For device options currently available refer to Table 13. For other options, voltage threshold values etc. or
for more information on any aspect of this device, please contact the ST sales office nearest you.
26/29
Doc ID 16101 Rev 5
STM6502, STM6503, STM6504, STM6505
7
Package marking
Package marking
Table 13.
Package marking
tSRC
delay
control
Smart
Reset
inputs(1)
VRST
RST
output(1)
TSR
AL
V
AL, OD
A
—
3VG
TSR
AL
S
AL, OD
B
—
4SG
STM6505SCABDG6F
CSRC
AL, PU
S
AL, OD
B
AL, OD
5SK
STM6505RCABDG6F
CSRC
AL, PU
R
AL, OD
B
AL, OD
5RK
STM6505WCABDG6F
CSRC
AL, PU
W
AL, OD
B
AL, OD
5WK
Part number
STM6503VEAADG6F
STM6504SEABDG6F
(2)
tREC
BLD
option output(1)
Topmark
1. AL = active-low, AH = active-high, PU = with internal pull-up resistor, OD = open-drain.
2. Contact local ST sales office for availability.
Figure 21. Package marking, top view
A
B
C
D
E
Topmark
A = dot (pin 1 reference)
B = assembly plant (P)
C = assembly year (Y, 0-9): 9 = 2009 etc.
D = assembly work week (WW, 01 to 52): 20 = WW20 etc.
E = marking area (topmark)
AM00479
Doc ID 16101 Rev 5
27/29
Revision history
8
STM6502, STM6503, STM6504, STM6505
Revision history
Table 14.
Document revision history
Date
Revision
31-Aug-2009
1
Initial release.
06-Nov-2009
2
Updated Applications, Section 1, Section , Figure 3 to Figure 6
updated and moved to Section , updated Table 1, Table 2, Table 3,
Table 4, Table 6, Table 12, Section 1.2.3, Section 1.2.7,
Section 1.2.9, Section 5, added package footprint, tape and reel
information, and Section 7.
15-Jan-2010
3
Updated Features, Section 1, Section 1.2.6, Table 1, Table 2,
Figure 5, Figure 6, Table 3, Table 6, Table 12, Table 13, removed
Table 4.
01-Mar-2010
4
Updated title of datasheet, Features, Applications, Table 1, 2, 6, 12,
footnote 5 of Table 6; updated Figure 3, 4; added Section 2: Typical
operating characteristics; minor textual and formatting changes.
5
Updated Features, Section 1, Figure 8, footnote 1 and 2 of Table 3,
updated Table 4, added footnote 2 to Table 4, Table 6, added
footnote 6 to Table 6, updated Table 6 to Table 9, and added footnote
2 of Table 13.
21-Jun-2010
28/29
Changes
Doc ID 16101 Rev 5
STM6502, STM6503, STM6504, STM6505
Please Read Carefully:
Information in this document is provided solely in connection with ST products. STMicroelectronics NV and its subsidiaries (“ST”) reserve the
right to make changes, corrections, modifications or improvements, to this document, and the products and services described herein at any
time, without notice.
All ST products are sold pursuant to ST’s terms and conditions of sale.
Purchasers are solely responsible for the choice, selection and use of the ST products and services described herein, and ST assumes no
liability whatsoever relating to the choice, selection or use of the ST products and services described herein.
No license, express or implied, by estoppel or otherwise, to any intellectual property rights is granted under this document. If any part of this
document refers to any third party products or services it shall not be deemed a license grant by ST for the use of such third party products
or services, or any intellectual property contained therein or considered as a warranty covering the use in any manner whatsoever of such
third party products or services or any intellectual property contained therein.
UNLESS OTHERWISE SET FORTH IN ST’S TERMS AND CONDITIONS OF SALE ST DISCLAIMS ANY EXPRESS OR IMPLIED
WARRANTY WITH RESPECT TO THE USE AND/OR SALE OF ST PRODUCTS INCLUDING WITHOUT LIMITATION IMPLIED
WARRANTIES OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE (AND THEIR EQUIVALENTS UNDER THE LAWS
OF ANY JURISDICTION), OR INFRINGEMENT OF ANY PATENT, COPYRIGHT OR OTHER INTELLECTUAL PROPERTY RIGHT.
UNLESS EXPRESSLY APPROVED IN WRITING BY AN AUTHORIZED ST REPRESENTATIVE, ST PRODUCTS ARE NOT
RECOMMENDED, AUTHORIZED OR WARRANTED FOR USE IN MILITARY, AIR CRAFT, SPACE, LIFE SAVING, OR LIFE SUSTAINING
APPLICATIONS, NOR IN PRODUCTS OR SYSTEMS WHERE FAILURE OR MALFUNCTION MAY RESULT IN PERSONAL INJURY,
DEATH, OR SEVERE PROPERTY OR ENVIRONMENTAL DAMAGE. ST PRODUCTS WHICH ARE NOT SPECIFIED AS "AUTOMOTIVE
GRADE" MAY ONLY BE USED IN AUTOMOTIVE APPLICATIONS AT USER’S OWN RISK.
Resale of ST products with provisions different from the statements and/or technical features set forth in this document shall immediately void
any warranty granted by ST for the ST product or service described herein and shall not create or extend in any manner whatsoever, any
liability of ST.
ST and the ST logo are trademarks or registered trademarks of ST in various countries.
Information in this document supersedes and replaces all information previously supplied.
The ST logo is a registered trademark of STMicroelectronics. All other names are the property of their respective owners.
© 2010 STMicroelectronics - All rights reserved
STMicroelectronics group of companies
Australia - Belgium - Brazil - Canada - China - Czech Republic - Finland - France - Germany - Hong Kong - India - Israel - Italy - Japan Malaysia - Malta - Morocco - Philippines - Singapore - Spain - Sweden - Switzerland - United Kingdom - United States of America
www.st.com
Doc ID 16101 Rev 5
29/29