FREESCALE 56858

56858
Data Sheet
Technical Data
56800E
16-bit Digital Signal Controllers
DSP56858
Rev. 6
01/2007
freescale.com
DSP56858 General Description
• 120 MIPS at 120MHz
• Two (2) Serial Communication Interfaces (SCI)
• 40K x 16-bit Program SRAM
• Serial Port Interface (SPI)
• 24K x 16-bit Data SRAM
• 8-bit Parallel Host Interface
• 1K x 16-bit Boot ROM
• General Purpose 16-bit Quad Timer
• Access up to 2M words of program memory or 8M data
memory
• JTAG/Enhanced On-Chip Emulation (OnCE™) for
unobtrusive, real-time debugging
• Chip Select Logic for glue-less interface to ROM and
SRAM
• Computer Operating Properly (COP)/Watchdog Timer
• Six (6) independent channels of DMA
• 144 LQFP and 144 MAPBGA packages
• Two (2) Enhanced Synchronous Serial Interfaces
(ESSI)
• Up to 47 GPIO
• Time-of -Day (TOD)
6
VDDIO
VDD
12
8
VSSIO
14
JTAG/
Enhanced
OnCE
Program Controller
and
Hardware Looping Unit
VSS VDDA
8
VSSA
2
16-Bit
56800E Core
Address
Generation Unit
Data ALU
16 x 16 + 36 → 36-Bit MAC
Three 16-bit Input Registers
Four 36-bit Accumulators
Bit
Manipulation
Unit
PAB
PDB
CDBR
CDBW
Data Memory
24,576 x 16 SRAM
XAB1
XAB2
System Bus
Control
PAB
DMA
6 channel
PDB
Core CLK
Boot ROM
1024 x 16 ROM
XDB2
CDBR
CDBW
DMA Requests
Memory
Program Memory
40,960 x 16 SRAM
IPRDB
IPAB
Decoding
Peripherals
A0-20 [20:0]
IPWDB
IPBus Bridge (IPBB)
IPBus CLK
External Address
Bus Switch
D0-D15 [15:0]
External Data
Bus Switch
RD Enable
WR Enable
CS0-CS3[3:0] or
GPIOA0-A3
Bus Control
POR
System
COP/TOD CLK Integration
Module
CLKO
3
MODE A-C or
GPIOH0-H2
RSTO
RESET
External Bus
Interface Unit
2 SCI ESSI0
or
or
GPIOE GPIOC
4
6
ESSI1
or
GPIOD
6
Quad
Timer
or
GPIOG
4
SPI
Host
Interrupt
or
Interface Controller
GPIOF
or
GPIOB
4
16
COP/
Watchdog
Time
of
Day
Clock
Generator
EXTAL
XTAL
OSC PLL
IRQA
IRQB
56858 Block Diagram
56858 Technical Data, Rev. 6
Freescale Semiconductor
3
Part 1 Overview
1.1 56858 Features
1.1.1
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
1.1.2
•
•
Digital Signal Processing Core
Efficient 16-bit engine with dual Harvard architecture
120 Million Instructions Per Second (MIPS) at 120MHz core frequency
Single-cycle 16 × 16-bit parallel Multiplier-Accumulator (MAC)
Four (4) 36-bit accumulators including extension bits
16-bit bidirectional shifter
Parallel instruction set with unique DSP addressing modes
Hardware DO and REP loops
Three (3) internal address buses and one (1) external address bus
Four (4) internal data buses and one (1) external data bus
Instruction set supports both DSP and controller functions
Four (4) hardware interrupt levels
Five (5) software interrupt levels
Controller-style addressing modes and instructions for compact code
Efficient C-Compiler and local variable support
Software subroutine and interrupt stack with depth limited only by memory
JTAG/Enhanced OnCE debug programming interface
Memory
Harvard architecture permits up to three (3) simultaneous accesses to program and data memory
On-Chip Memory
— 40K × 16-bit Program RAM
— 24K × 16-bit Data RAM
— 1K × 16-bit Boot ROM
•
Off-Chip Memory Expansion (EMI)
— Access up to 2M words of program or 8M data memory (using chip selects)
— Chip Select Logic for glue-less interface to ROM and SRAM
1.1.3
•
•
•
•
•
•
56858 Peripheral Circuit Features
General Purpose 16-bit Quad Timer*
Two Serial Communication Interfaces (SCI)*
Serial Peripheral Interface (SPI) Port*
Two (2) Enhanced Synchronous Serial Interface (ESSI) modules*
Computer Operating Properly (COP)/Watchdog Timer
JTAG/Enhanced On-Chip Emulation (EOnCE) for unobtrusive, real-time debugging
56858 Technical Data, Rev. 6
4
Freescale Semiconductor
56858 Description
•
•
•
•
Six (6) independent channels of DMA
8-bit Parallel Host Interface*
Time-of-Day (TOD)
Up to 47 GPIO
* Each peripheral I/O can be used alternately as a GPIO if not needed
1.1.4
•
•
Energy Information
Fabricated in high-density CMOS with 3.3V, TTL-compatible digital inputs
Wait and Stop modes available
1.2 56858 Description
The 56858 is a member of the 56800E core-based family of controllers. This device combines the
processing power of a Digital Signal Processor (DSP) and the functionality of a microcontroller with a
flexible set of peripherals on a single chip to create an extremely cost-effective solution. The low cost,
flexibility, and compact program code make this device well-suited for many applications. The 56858
includes peripherals that are especially useful for teledatacom devices; Internet appliances; portable
devices; TAD; voice recognition; hands-free devices; and general purpose applications.
The 56800E core is based on a Harvard-style architecture consisting of three execution units operating in
parallel, allowing as many as six operations per instruction cycle. The microprocessor-style programming
model and optimized instruction set allow straightforward generation of efficient, compact DSP and
control code. The instruction set is also highly efficient for C Compilers, enabling rapid development of
optimized control applications.
The 56858 supports program execution from either internal or external memories. Two data operands can
be accessed from the on-chip Data RAM per instruction cycle. The 56858 also provides two external
dedicated interrupt lines, and up to 47 General Purpose Input/Output (GPIO) lines, depending on
peripheral configuration.
The 56858 controller includes 40K words of Program RAM, 24K words of Data RAM and 1K of Boot
RAM. It also supports program execution from external memory.
This controller also provides a full set of standard programmable peripherals that include an 8-bit Parallel
Host Interface, two Enhanced Synchronous Serial Interfaces (ESSI), one Serial Peripheral Interface (SPI),
two Serial Communications Interfaces (SCI), and one Quad Timer. The Host Interface, Quad Timer, SSI,
SPI, SCI I/O and four chip selects can be used as General Purpose Input/Outputs when its primary function
is not required.
1.3 State of the Art Development Environment
•
•
Processor ExpertTM (PE) provides a Rapid Application Design (RAD) tool that combines easy-to-use
component-based software application creation with an expert knowledge system.
The Code Warrior Integrated Development Environment is a sophisticated tool for code navigation,
compiling, and debugging. A complete set of evaluation modules (EVMs) and development system cards
will support concurrent engineering. Together, PE, Code Warrior and EVMs create a complete, scalable
tools solution for easy, fast, and efficient development.
56858 Technical Data, Rev. 6
Freescale Semiconductor
5
1.4 Product Documentation
The four documents listed in Table 1-1 are required for a complete description of and proper design with
the 56858. Documentation is available from local Freescale distributors, Freescale Semiconductor sales
offices, Freescale Literature Distribution Centers, or online at www.freescale.com.
Table 1-1 56858 Chip Documentation
Topic
Description
Order Number
56800E
Reference Manual
Detailed description of the 56800E architecture, 16-bit
core processor and the instruction set
56800ERM
DSP56858
User’s Manual
Detailed description of memory, peripherals, and
interfaces of the 56858
DSP5685xUM
56858
Technical Data Sheet
Electrical and timing specifications, pin descriptions,
and package descriptions (this document)
DSP56858
DSP56858
Errata
Details any chip issues that might be present
DSP56858E
1.5 Data Sheet Conventions
This data sheet uses the following conventions:
OVERBAR
This is used to indicate a signal that is active when pulled low. For example, the RESET pin is
active when low.
“asserted”
A high true (active high) signal is high or a low true (active low) signal is low.
“deasserted”
A high true (active high) signal is low or a low true (active low) signal is high.
Examples:
Signal/Symbol
Logic State
Signal State
Voltage1
PIN
True
Asserted
VIL/VOL
PIN
False
Deasserted
VIH/VOH
PIN
True
Asserted
VIH/VOH
PIN
False
Deasserted
VIL/VOL
1. Values for VIL, VOL, VIH, and VOH are defined by individual product specifications.
56858 Technical Data, Rev. 6
6
Freescale Semiconductor
Introduction
Part 2 Signal/Connection Descriptions
2.1 Introduction
The input and output signals of the 56858 are organized into functional groups, as shown in Table 2-1 and
as illustrated in Figure 2-1. In Table 3-1 each table row describes the package pin and the signal or signals
present.
Table 2-1 56858 Functional Group Pin Allocations
Functional Group
Number of Pins
Power (VDD, VDDIO, or VDDA)
(8, 12, 1)1
Ground (VSS, VSSIO,or VSSA)
(8, 14, 2)1
PLL and Clock
3
External Bus Signals
39
External Chip Select*
4
Interrupt and Program Control
72
Host Interface (HI)*
163
Enhanced Synchronous Serial Interface (ESSI0) Port*
6
Enhanced Synchronous Serial Interface (ESSI1) Port*
6
Serial Communications Interface (SCI0) Ports*
2
Serial Communications Interface (SCI1) Ports*
2
Serial Peripheral Interface (SPI) Port*
4
Quad Timer Module Port*
4
JTAG/On-Chip Emulation (OnCE)
6
*Alternately, GPIO pins
1. VDD = VDD CORE, VSS = VSS CORE, VDDIO= VDD IO, VSSIO = VSS IO, VDDA = VDD ANA, VSSA = VSS ANA
2. MODA, MODB and MODC can be used as GPIO after the bootstrap process has completed.
3. The following Host Interface signals are multiplexed: HRWB to HRD, HDS to HWR, HREQ to HTRQ and HACK to HRRQ.
56858 Technical Data, Rev. 6
Freescale Semiconductor
7
Logic
Power
VDD
VSS
1
8
1
8
56858
I/O
Power
VDDIO
VSSIO
12
1
1
14
1
Analog
Power1
VDDA
VSSA
1
2
1
1
1
1
A0 - A20
Address
Bus
D0 - D15
RD
WR
21
1
16
1
1
1
1
1
1
Chip
Select
CS0 - CS3 (GPIOA0 - A3)
4
1
1
HD0 - HD7 (GPIOB0 - B7)
HA0 - HA2 (GPIOB8 - B10)
HRWB (HRD) (GPIOB11)
Host
Interface
HDS (HWR) (GPIOB12)
HCS (GPIOB13)
HREQ (HTRQ) (GPIOB14)
HACK (HRRQ) (GPIOB15)
Timer
Module
TIO0 - TIO3 (GPIOG0 - G3)
IRQA
IRQB
Interrupt /
Program
Control
MODA, MODB, MODC
(GPIOH0 - H2)
RESET
RSTO
8
3
1
1
1
1
1
1
1
RXDO (GPIOE0)
SCI 0
TXDO (GPIOE1)
RXD1 (GPIOE2)
SCI 2
TXD1 (GPIOE3)
STD0 (GPIOC0)
SRD0 (GPIOC1)
SCK0 (GPIOC2)
ESSI 0
SC00 (GPIOC3)
SC01 (GPIOC4)
SC02 (GPIOC5)
STD1 (GPIOD0)
SRD1 (GPIOD1)
SCK1 (GPIOD2)
ESSI 1
SC10 (GPIOD3)
SC11 (GPIOD4)
SC12 (GPIOD5)
MISO (GPIOF0)
MOSI (GPIOF1)
SPI
SCK (GPIOF2)
SS (GPIOF3)
1
1
1
1
4
1
1
1
1
1
1
3
1
1
1
1
1
XTAL
EXTAL
PLL /
Clock
CLKO
TCK
TDI
TDO
JTAG /
Enhanced
OnCE
TMS
TRST
DE
Figure 2-1 56858 Signals Identified by Functional Group2
1. Specifically for PLL, OSC, and POR.
2. Alternate pin functions are shown in parentheses. Pin direction/type is represented as the preferred functionality. GPIO may provide
bidirectional use of any pin.
56858 Technical Data, Rev. 6
8
Freescale Semiconductor
Introduction
Part 3 Signals and Package Information
All digital inputs have a weak internal pull-up circuit associated with them. These pull-up circuits are
enabled by default. Exceptions:
1. When a pin has GPIO functionality, the pull-up may be disabled under software control.
2. MODE A, MODE B and MODE C pins have no pull-up.
3. TCK has a weak pull-down circuit always active.
4. Bidirectional I/O pullups automatically disable when the output is enabled.
This table is presented consistently with the Signals Identified by Functional Group figure.
1. BOLD entries in the Type column represents the state of the pin just out of reset.
2. Output(Z) means an output in a High-Z condition.
Table 3-1 56858 Signal and Package Information for the 144-pin LQFP and MAPBGA
Signal
Name
BGA
Pin No.
LQFP
Pin No.
Type
VDD
E1
14
VDD
VDD
M6
36
Logic Power (VDD)—These pins provide power to the internal
structures of the chip, and should all be attached to VDD.
VDD
F12
52
VDD
A9
72
VDD
M2
87
VDD
J12
88
VDD
E12
109
VDD
A12
125
VSS
G1
15
VSS
VSS
L6
16
Logic Power–Ground (VSS)—These pins provide grounding for the
internal structures of the chip and should all be attached to VSS.
VSS
D12
53
VSS
A7
54
VSS
F1
71
VSS
M7
89
VSS
K12
126
VSS
A8
127
Description
56858 Technical Data, Rev. 6
Freescale Semiconductor
9
Table 3-1 56858 Signal and Package Information for the 144-pin LQFP and MAPBGA
Signal
Name
BGA
Pin No.
LQFP
Pin No.
Type
VDDIO
B1
5
VDDIO
VDDIO
H1
6
I/O Power (VDDIO)—These pins provide power for all I/O and ESD
structures of the chip and should all be attached to VDDIO (3.3V).
VDDIO
M3
20
VDDIO
M8
45
VDDIO
M11
61
VDDIO
H12
67
VDDIO
C12
68
VDDIO
A11
80
VDDIO
A5
105
VDDIO
A3
113
VDDIO
C1
129
VDDIO
M10
139
VSSIO
D1
7
VSSIO
VSSIO
J1
21
I/O Power–Ground (VSSIO)—These pins provide grounding for all I/O
and ESD structures of the chip and should all be attached to VSS.
VSSIO
M5
46
VSSIO
M9
47
VSSIO
L12
62
VSSIO
G12
69
VSSIO
B12
70
VSSIO
A10
82
VSSIO
A4
106
VSSIO
A1
115
VSSIO
A2
128
VSSIO
M4
130
VSSIO
M12
140
VSSIO
A6
141
VDDA
K1
24
VDDA
Analog Power (VDDA)—These pins supply an analog power source.
VSSA
M1
25
VSSA
L1
26
VSSA
Description
Analog Ground (VSSA)—This pin supplies an analog ground.
56858 Technical Data, Rev. 6
10
Freescale Semiconductor
Introduction
Table 3-1 56858 Signal and Package Information for the 144-pin LQFP and MAPBGA
Signal
Name
BGA
Pin No.
LQFP
Pin No.
Type
A0
E5
10
Output(Z)
A1
E4
11
A2
E3
12
A3
E2
13
A4
J2
29
A5
H3
30
A6
G4
31
A7
H4
32
A8
G5
48
A9
L5
49
A10
J6
50
A11
K6
51
A12
J8
63
A13
K8
64
A14
L9
65
A15
K9
66
A16
K10
75
A17
K11
76
A18
J9
77
A19
J10
78
A20
J11
79
Description
Address Bus (A0-A20)—These signals specify a word address for
external program or data memory access.
56858 Technical Data, Rev. 6
Freescale Semiconductor
11
Table 3-1 56858 Signal and Package Information for the 144-pin LQFP and MAPBGA
Signal
Name
BGA
Pin No.
LQFP
Pin No.
D0
H7
81
D1
G7
94
D2
F9
95
D3
F10
96
D4
F11
97
D5
E10
98
D6
D7
120
D7
B7
121
D8
E7
122
D9
F8
123
D10
F7
124
D11
D5
137
D12
B4
138
D13
C4
142
D14
F6
143
D15
B3
144
RD
D3
8
Type
Input/
Output(Z)
Output
Description
Data Bus (D0-D15)—These pins provide the bidirectional data for
external program or data memory accesses.
Read Enable (RD) — is asserted during external memory read cycles.
This signal is pulled high during reset.
WR
D4
9
Output
Write Enable (WR) —is asserted during external memory write cycles.
This signal is pulled high during reset.
CS0
H8
83
Input/Output
GPIOA0
CS1
H9
84
H11
85
GPIOA3
Output
Input/Output
GPIOA2
CS3
Output
Input/Output
GPIOA1
CS2
Output
H10
86
Output
Input/Output
External Chip Select (CS0)—This pin is used as a dedicated GPIO.
Port A GPIO (0) —This pin is a General Purpose I/O (GPIO) pin when
not configured for host port usage.
External Chip Select (CS1)—This pin is used as a dedicated GPIO.
Port A GPIO (1) —This pin is a General Purpose I/O (GPIO) pin when
not configured for host port usage.
External Chip Select (CS2)—This pin is used as a dedicated GPIO.
Port A GPIO (2) —This pin is a General Purpose I/O (GPIO) pin when
not configured for host port usage.
External Chip Select (CS3)—This pin is used as a dedicated GPIO.
Port A GPIO (3)—This pin is a General Purpose I/O (GPIO) pin when
not configured for host port usage.
56858 Technical Data, Rev. 6
12
Freescale Semiconductor
Introduction
Table 3-1 56858 Signal and Package Information for the 144-pin LQFP and MAPBGA
Signal
Name
BGA
Pin No.
LQFP
Pin No.
Type
HD0
J3
33
Input
Description
Host Address (HD0)—This input provides data selection for HI
registers.
This pin is disconnected internally during reset.
GPIOB0
HD1
Input/Output
K2
34
Input
Port B GPIO (0)—This pin is a General Purpose I/O (GPIO) pin when
not configured for host port usage.
Host Address (HD1)—This input provides data selection for HI
registers.
This pin is disconnected internally during reset.
GPIOB1
HD2
Input/Output
L2
35
Input
Port B GPIO (1)—This pin is a General Purpose I/O (GPIO) pin when
not configured for host port usage.
Host Address (HD2)—This input provides data selection for HI
registers.
This pin is disconnected internally during reset.
GPIOB2
HD3
Input/Output
J4
40
Input
Port B GPIO (2)—This pin is a General Purpose I/O (GPIO) pin when
not configured for host port usage.
Host Address (HD3)—This input provides data selection for HI
registers.
This pin is disconnected internally during reset.
GPIOB3
HD4
Input/Output
L4
41
Input
Port B GPIO (3)—This pin is a General Purpose I/O (GPIO) pin when
not configured for host port usage.
Host Address (HD4)—This input provides data selection for HI
registers.
This pin is disconnected internally during reset.
GPIOB4
HD5
Input/Output
J5
42
Input
Port B GPIO (4)—This pin is a General Purpose I/O (GPIO) pin when
not configured for host port usage.
Host Address (HD5)—This input provides data selection for HI
registers.
This pin is disconnected internally during reset.
GPIOB5
Input/Output
Port B GPIO (5)—This pin is a General Purpose I/O (GPIO) pin when
not configured for host port usage.
56858 Technical Data, Rev. 6
Freescale Semiconductor
13
Table 3-1 56858 Signal and Package Information for the 144-pin LQFP and MAPBGA
Signal
Name
BGA
Pin No.
LQFP
Pin No.
Type
HD6
K5
43
Input
Description
Host Address (HD6)—This input provides data selection for HI
registers.
This pin is disconnected internally during reset.
GPIOB6
HD7
Input/Output
H5
44
Input
Port B GPIO (6)—This pin is a General Purpose I/O (GPIO) pin when
not configured for host port usage.
Host Address (HD7)—This input provides data selection for HI
registers.
This pin is disconnected internally during reset.
GPIOB7
HA0
G10
90
Input/Output
Port B GPIO (7)—This pin is a General Purpose I/O (GPIO) pin when
not configured for host port usage.
Input
Host Address (HA0)—These inputs provide the address selection for
HI registers.
These pins are disconnected internally during reset.
GPIOB8
HA1
Input/Output
G11
91
Input
Port B GPIO (8)—These pins are General Purpose I/O (GPIO) pins
when not configured for host port usage.
Host Address (HA0)—These inputs provide the address selection for
HI registers.
These pins are disconnected internally during reset.
GPIOB9
HA2
Input/Output
G9
92
Input
Port B GPIO (9)—These pins are General Purpose I/O (GPIO) pins
when not configured for host port usage.
Host Address (HA0)—These inputs provide the address selection for
HI registers.
These pins are disconnected internally during reset.
GPIOB10
HRWB
Input/Output
G8
93
Input
Port B GPIO (10)—These pins are General Purpose I/O (GPIO) pins
when not configured for host port usage.
Host Read/Write (HRWB)—When the HI08 is programmed to
interface to a single-data-strobe host bus and the HI function is
selected, this signal is the Read/Write input.
These pins are disconnected internally during reset.
HRD
Input
GPIOB11
Input/Output
Host Read Data (HRD)—This signal is the Read Data input when the
HI08 is programmed to interface to a double-data-strobe host bus and
the HI function is selected.
Port B GPIO (11) —This pin is a General Purpose I/O (GPIO) pin
when not configured for host port usage.
56858 Technical Data, Rev. 6
14
Freescale Semiconductor
Introduction
Table 3-1 56858 Signal and Package Information for the 144-pin LQFP and MAPBGA
Signal
Name
BGA
Pin No.
LQFP
Pin No.
Type
Description
HDS
C8
116
Input
Host Data Strobe (HDS)—When the HI08 is programmed to interface
to a single-data-strobe host bus and the HI function is selected, this
input enables a data transfer on the HI when HCS is asserted.
These pins are disconnected internally during reset.
HWR
Input
Host Write Enable (HWR)—This signal is the Write Data input when
the HI08 is programmed to interface to a double-data-strobe host bus
and the HI function is selected.
GPIOB12
Input/Output
Port B GPIO (12)—This pin is a General Purpose I/O (GPIO) pin when
not configured for host port usage.
HCS
D8
117
Input
Host Chip Select (HCS)—This input is the chip select input for the
Host Interface.
These pins are disconnected internally during reset.
GPIOB13
HREQ
B8
118
Input/Output
Port B GPIO (13)—This pin is a General Purpose I/O (GPIO) pin when
not configured for host port usage.
Open Drain
Output
Host Request (HREQ)—When the HI08 is programmed for HRMS=0
functionality (typically used on a single-data-strobe bus), this open
drain output is used by the HI to request service from the host
processor. The HREQ may be connected to an interrupt request pin of
a host processor, a transfer request of a DMA controller, or a control
input of external circuitry.
These pins are disconnected internally during reset.
HTRQ
Open Drain
Output
Transmit Host Request (HTRQ)—This signal is the Transmit Host
Request output when the HI08 is programmed for HRMS=1
functionality and is typically used on a double-data-strobe bus.
GPIOB14
Input/Output
Port B GPIO (14) —This pin is a General Purpose I/O (GPIO) pin
when not configured for host port usage.
56858 Technical Data, Rev. 6
Freescale Semiconductor
15
Table 3-1 56858 Signal and Package Information for the 144-pin LQFP and MAPBGA
Signal
Name
BGA
Pin No.
LQFP
Pin No.
Type
Description
HACK
C7
119
Input
Host Acknowledge (HACK)—When the HI08 is programmed for
HRMS=0 functionality (typically used on a single-data-strobe bus), this
input has two functions: (1) provide a Host Acknowledge signal for
DMA transfers or (2) to control handshaking and provide a Host
Interrupt Acknowledge compatible with the MC68000 family
processors.
These pins are disconnected internally during reset.
HRRQ
Open Drain
Output
Receive Host Request (HRRQ)—This signal is the Receive Host
Request output when the HI08 is programmed for HRMS=1
functionality and is typically used on a double-data-strobe bus.
GPIOB15
Input/Output
Port B GPIO (15)—This pin is a General Purpose I/O (GPIO) pin when
not configured for host port usage.
Input/Output
Timer Input/Outputs (TIO0)—This pin can be independently
configured to be either a timer input source or an output flag.
Input/Output
Port G GPIOG0—This pin is a General Purpose I/O (GPIO) pin that
can individually be programmed as an input or output pin.
Input/Output
Timer Input/Outputs (TIO1)—This pin can be independently
configured to be either a timer input source or an output flag.
Input/Output
Port G GPIO (1)—This pin is a General Purpose I/O (GPIO) pin that
can individually be programmed as an input or output pin.
Input/Output
Timer Input/Outputs (TIO2)—This pin can be independently
configured to be either a timer input source or an output flag.
Input/Output
Port G GPIO (2)—This pin is a General Purpose I/O (GPIO) pin that
can individually be programmed as an input or output pin.
Input/Output
Timer Input/Outputs (TIO3)—This pin can be independently
configured to be either a timer input source or an output flag.
Input/Output
Port G GPIO (3)—This pin is a General Purpose I/O (GPIO) pin that
can individually be programmed as an input or output pin.
Input
External Interrupt Request A and B—The IRQA and IRQB inputs
are asynchronous external interrupt requests that indicate that an
external device is requesting service. A Schmitt trigger input is used
for noise immunity. They can be programmed to be level-sensitive or
negative-edge-triggered. If level-sensitive triggering is selected, an
external pull-up resistor is required for Wired-OR operation.
Input
Mode Select (MODE A)—During the bootstrap process MODE A
selects one of the eight bootstrap modes.
TIO0
B9
114
GPIOG0
TIO1
C9
112
GPIOG1
TIO2
D9
111
GPIOG2
TIO3
B10
110
GPIOG3
IRQA
G2
22
IRQB
F5
23
MODE A
F4
17
GPIOH0
Input/Output
Port H GPIO (0)—This pin is a General Purpose I/O (GPIO) pin after
the bootstrap process has completed.
56858 Technical Data, Rev. 6
16
Freescale Semiconductor
Introduction
Table 3-1 56858 Signal and Package Information for the 144-pin LQFP and MAPBGA
Signal
Name
BGA
Pin No.
LQFP
Pin No.
Type
MODE B
F3
18
Input
GPIOH1
MODE C
Input/Output
F2
19
GPIOH2
RESET
K4
39
Input
Description
Mode Select (MODE B)—During the bootstrap process MODE A
selects one of the eight bootstrap modes.
Port H GPIO (1)—This pin is a General Purpose I/O (GPIO) pin after
the bootstrap process has completed.
Mode Select (MODE C)—During the bootstrap process MODE A
selects one of the eight bootstrap modes.
Input/Output
Port H GPIO (2)—This pin is a General Purpose I/O (GPIO) pin after
the bootstrap process has completed.
Input
Reset (RESET)—This input is a direct hardware reset on the
processor. When RESET is asserted low, the device is initialized and
placed in the Reset state. A Schmitt trigger input is used for noise
immunity. When the RESET pin is deasserted, the initial chip operating
mode is latched from the MODE A, MODE B, and MODE C pins.
To ensure complete hardware reset, RESET and TRST should be
asserted together. The only exception occurs in a debugging
environment when a hardware reset is required and it is necessary not
to reset the JTAG/Enhanced OnCE module. In this case, assert
RESET, but do not assert TRST.
RSTO
K3
38
Output
Reset Output (RSTO)—This output is asserted on any reset condition
(external reset, low voltage, software, or COP).
RXD0
L10
73
Input
Serial Receive Data 0 (RXD0)—This input receives byte-oriented
serial data and transfers it to the SCI 0 receive shift register.
GPIOE0
TXD0
L11
74
GPIOE1
RXD1
B11
107
GPIOE2
TXD1
C10
GPIOE3
108
Input/Output
Port E GPIO (0)—This pin is a General Purpose I/O (GPIO) pin that
can individually be programmed as input or output pin.
Output(Z)
Serial Transmit Data 0 (TXD0)—This signal transmits data from the
SCI 0 transmit data register.
Input/Output
Port E GPIO (1)—This pin is a General Purpose I/O (GPIO) pin that
can individually be programmed as input or output pin.
Input
Serial Receive Data 1 (RXD1)—This input receives byte-oriented
serial data and transfers it to the SCI 1 receive shift register.
Input/Output
Port E GPIO (2)—This pin is a General Purpose I/O (GPIO) pin that
can individually be programmed as input or output pin.
Output(Z)
Serial Transmit Data 1 (TXD1)—This signal transmits data from the
SCI 1 transmit data register.
Input/Output
Port E GPIO (3)—This pin is a General Purpose I/O (GPIO) pin that
can individually be programmed as input or output pin.
56858 Technical Data, Rev. 6
Freescale Semiconductor
17
Table 3-1 56858 Signal and Package Information for the 144-pin LQFP and MAPBGA
Signal
Name
BGA
Pin No.
LQFP
Pin No.
Type
STD0
B6
131
Output
GPIOC0
SRD0
Input/Output
C6
132
GPIOC1
SCK0
C5
133
GPIOC2
SC00
D6
134
GPIOC3
SC01
B5
135
GPIOC4
SC02
GPIOC5
E6
136
Input
Description
ESSI Transmit Data (STD0)—This output pin transmits serial data
from the ESSI Transmitter Shift Register.
Port C GPIO (0)—This pin is a General Purpose I/O (GPIO) pin when
the ESSI is not in use.
ESSI Receive Data (SRD0)—This input pin receives serial data and
transfers the data to the ESSI Receive Shift Register.
Input/Output
Port C GPIO (1)—This pin is a General Purpose I/O (GPIO) pin when
the ESSI is not in use.
Input/Output
ESSI Serial Clock (SCK0)—This bidirectional pin provides the serial
bit rate clock for the transmit section of the ESSI. The clock signal can
be continuous or gated and can be used by both the transmitter and
receiver in synchronous mode.
Input/Output
Port C GPIO (2)—This pin is a General Purpose I/O (GPIO) pin when
the ESSI is not in use.
Input/Output
ESSI Serial Control Pin 0 (SC00)—The function of this pin is
determined by the selection of either synchronous or asynchronous
mode. For asynchronous mode, this pin will be used for the receive
clock I/O. For synchronous mode, this pin is used either for
transmitter1 output or for serial I/O flag 0.
Input/Output
Port C GPIO (3)—This pin is a General Purpose I/O (GPIO) pin when
the ESSI is not in use.
Input/Output
ESSI Serial Control Pin 1 (SC01)—The function of this pin is
determined by the selection of either synchronous or asynchronous
mode. For asynchronous mode, this pin is the receiver frame sync I/O.
For synchronous mode, this pin is used either for transmitter2 output
or for serial I/O flag 1.
Input/Output
Port C GPIO (4)—This pin is a General Purpose I/O (GPIO) pin when
the ESSI is not in use.
Input/Output
ESSI Serial Control Pin 2 (SC02)—This pin is used for frame sync
I/O. SC02 is the frame sync for both the transmitter and receiver in
synchronous mode and for the transmitter only in asynchronous mode.
When configured as an output, this pin is the internally generated
frame sync signal. When configured as an input, this pin receives an
external frame sync signal for the transmitter (and the receiver in
synchronous operation).
Input or Output Port C GPIO (5)—This pin is a General Purpose I/O (GPIO) pin when
the ESSI is not in use.
56858 Technical Data, Rev. 6
18
Freescale Semiconductor
Introduction
Table 3-1 56858 Signal and Package Information for the 144-pin LQFP and MAPBGA
Signal
Name
BGA
Pin No.
LQFP
Pin No.
Type
STD1
E8
99
Output
GPIOD0
SRD1
Input/Output
E11
100
GPIOD1
SCK1
E9
101
GPIOD2
SC10
D10
102
GPIOD3
SC11
D11
103
GPIOD4
SC12
C11
GPIOC5
104
Input
Description
ESSI Transmit Data (STD1)—This output pin transmits serial data
from the ESSI Transmitter Shift Register.
Port D GPIO (0)—This pin is a General Purpose I/O (GPIO) pin when
the ESSI is not in use.
ESSI Receive Data (SRD1)—This input pin receives serial data and
transfers the data to the ESSI Receive Shift Register.
Input/Output
Port D GPIO (1)—This pin is a General Purpose I/O (GPIO) pin when
the ESSI is not in use.
Input/Output
ESSI Serial Clock (SCK1)—This bidirectional pin provides the serial
bit rate clock for the transmit section of the ESSI. The clock signal can
be continuous or gated and can be used by both the transmitter and
receiver in synchronous mode.
Input/Output
Port D GPIO (2)—This pin is a General Purpose I/O (GPIO) pin when
the ESSI is not in use.
Input/Output
ESSI Serial Control Pin 0 (SC10)—The function of this pin is
determined by the selection of either synchronous or asynchronous
mode. For asynchronous mode, this pin will be used for the receive
clock I/O. For synchronous mode, this pin is used either for
transmitter1 output or for serial I/O flag 0.
Input/Output
Port D GPIO (3)—This pin is a General Purpose I/O (GPIO) pin when
the ESSI is not in use.
Input/Output
ESSI Serial Control Pin 1 (SC11)—The function of this pin is
determined by the selection of either synchronous or asynchronous
mode. For asynchronous mode, this pin is the receiver frame sync I/O.
For synchronous mode, this pin is used either for transmitter2 output
or for serial I/O flag 1.
Input/Output
Port D GPIO (4)—This pin is a General Purpose I/O (GPIO) pin when
the ESSI is not in use.
Input/Output
ESSI Serial Control Pin 2 (SC12)—This pin is used for frame sync
I/O. SC02 is the frame sync for both the transmitter and receiver in
synchronous mode and for the transmitter only in asynchronous mode.
When configured as an output, this pin is the internally generated
frame sync signal. When configured as an input, this pin receives an
external frame sync signal for the transmitter (and the receiver in
synchronous operation).
Input/Output
Port D GPIO (5)—This pin is a General Purpose I/O (GPIO) pin when
the ESSI is not in use.
56858 Technical Data, Rev. 6
Freescale Semiconductor
19
Table 3-1 56858 Signal and Package Information for the 144-pin LQFP and MAPBGA
Signal
Name
BGA
Pin No.
LQFP
Pin No.
Type
Description
MISO
B2
1
Input/Output
SPI Master In/Slave Out (MISO)—This serial data pin is an input to a
master device and an output from a slave device. The MISO line of a
slave device is placed in the high-impedance state if the slave device
is not selected. The driver on this pin can be configured as an
open-drain driver by the SPI’s Wired-OR mode (WOM) bit when this
pin is configured for SPI operation.
Input/Output
Port F GPIO (0)—This pin is a General Purpose I/O (GPIO) pin that
can individually be programmed as input or output pin.
GPIOF0
MOSI
C3
2
GPIOF1
SCK
C2
3
GPIOF2
SS
D2
4
GPIOF3
Input/
Output (Z)
SPI Master Out/Slave In (MOSI)—This serial data pin is an output
from a master device and an input to a slave device. The master
device places data on the MOSI line a half-cycle before the clock edge
that the slave device uses to latch the data. The driver on this pin can
be configured as an open-drain driver by the SPI’s WOM bit when this
pin is configured for SPI operation.
Input/Output
Port F GPIO (1)—This pin is a General Purpose I/O (GPIO) pin that
can be individually programmed as input or output pin.
Input/Output
SPI Serial Clock (SCK)—This bidirectional pin provides a serial bit
rate clock for the SPI. This gated clock signal is an input to a slave
device and is generated as an output by a master device. Slave
devices ignore the SCK signal unless the SS pin is active low. In both
master and slave SPI devices, data is shifted on one edge of the SCK
signal and is sampled on the opposite edge where data is stable. The
driver on this pin can be configured as an open-drain driver by the
SPI’s WOM bit when this pin is configured for SPI operation. When
using Wired-OR mode, the user must provide an external pull-up
device.
Input/Output
Port F GPIO (2)—This pin is a General Purpose I/O (GPIO) pin that
can individually be programmed as input or output pin.
Input
SPI Slave Select (SS)—This input pin selects a slave device before a
master device can exchange data with the slave device. SS must be
low before data transactions and must stay low for the duration of the
transaction. The SS line of the master must be held high.
Input/Output
Port F GPIO (3)—This pin is a General Purpose I/O (GPIO) pin that
can individually be programmed as input or output pin.
XTAL
H2
27
Input/Output
Crystal Oscillator Output (XTAL)—This output connects the internal
crystal oscillator output to an external crystal. If an external clock
source other than a crystal oscillator is used, XTAL must be used as
the input.
EXTAL
G3
28
Input
External Crystal Oscillator Input (EXTAL)—This input should be
connected to an external crystal. If an external clock source other than
a crystal oscillator is used, EXTAL must be tied off. See Section 4.5.2
CLKO
L3
37
Output
Clock Output (CLKO)—This pin outputs a buffered clock signal.
When enabled, this signal is the system clock divided by four.
56858 Technical Data, Rev. 6
20
Freescale Semiconductor
Introduction
Table 3-1 56858 Signal and Package Information for the 144-pin LQFP and MAPBGA
Signal
Name
BGA
Pin No.
LQFP
Pin No.
Type
TCK
L8
60
Input
Test Clock Input (TCK)—This input pin provides a gated clock to
synchronize the test logic and to shift serial data to the JTAG/OnCE
port. The pin is connected internally to a pull-down resistor.
TDI
K7
58
Input
Test Data Input (TDI)—This input pin provides a serial input data
stream to the JTAG/OnCE port. It is sampled on the rising edge of
TCK and has an on-chip pull-up resistor.
TDO
G6
57
Output(Z)
TMS
J7
59
Input
Description
Test Data Output (TDO)—This tri-statable output pin provides a serial
output data stream from the JTAG/Enhanced OnCE port. It is driven in
the Shift-IR and Shift-DR controller states, and changes on the falling
edge of TCK.
Test Mode Select Input (TMS)—This input pin is used to sequence
the JTAG TAP controller’s state machine. It is sampled on the rising
edge of TCK and has an on-chip pull-up resistor.
Note:
TRST
L7
56
Input
Always tie the TMS pin to VDD through a 2.2K resistor.
Test Reset (TRST)—As an input, a low signal on this pin provides a
reset signal to the JTAG TAP controller. To ensure complete hardware
reset, TRST should be asserted whenever RESET is asserted. The
only exception occurs in a debugging environment, since the
Enhanced OnCE/JTAG module is under the control of the debugger. In
this case it is not necessary to assert TRST when asserting RESET.
Outside of a debugging environment RESET should be permanently
asserted by grounding the signal, thus disabling the Enhanced
OnCE/JTAG module on the device.
Note: For normal operation, connect TRST directly to VSS. If the design is
to be used in a debugging environment, TRST may be tied to VSS through a
1K resistor.
56858 Technical Data, Rev. 6
Freescale Semiconductor
21
Table 3-1 56858 Signal and Package Information for the 144-pin LQFP and MAPBGA
Signal
Name
BGA
Pin No.
LQFP
Pin No.
Type
Description
DE
H6
55
Input/Output
Debug Event (DE)—This is an open-drain, bidirectional, active low
signal. As an input, it is a means of entering debug mode of operation
from an external command controller. As an output, it is a means of
acknowledging that the chip has entered debug mode.
This pin is connected internally to a weak pull-up resistor.
Part 4 Specifications
4.1 General Characteristics
The 56858 is fabricated in high-density CMOS with 5-volt tolerant TTL-compatible digital inputs. The
term “5-volt tolerant” refers to the capability of an I/O pin, built on a 3.3V compatible process technology,
to withstand a voltage up to 5.5V without damaging the device. Many systems have a mixture of devices
designed for 3.3V and 5V power supplies. In such systems, a bus may carry both 3.3V and 5V-compatible
I/O voltage levels (a standard 3.3V I/O is designed to receive a maximum voltage of 3.3V ± 10% during
normal operation without causing damage). This 5V tolerant capability therefore offers the power savings
of 3.3V I/O levels while being able to receive 5V levels without being damaged.
Absolute maximum ratings given in Table 4-1 are stress ratings only, and functional operation at the
maximum is not guaranteed. Stress beyond these ratings may affect device reliability or cause permanent
damage to the device.
The 56858 DC/AC electrical specifications are preliminary and are from design simulations. These
specifications may not be fully tested or guaranteed at this early stage of the product life cycle. Finalized
specifications will be published after complete characterization and device qualifications have been
completed.
56858 Technical Data, Rev. 6
22
Freescale Semiconductor
General Characteristics
CAUTION
This device contains protective circuitry to guard
against damage due to high static voltage or
electrical fields. However, normal precautions are
advised to avoid application of any voltages higher
than maximum rated voltages to this high-impedance
circuit. Reliability of operation is enhanced if unused
inputs are tied to an appropriate voltage level.
Table 4-1 Absolute Maximum Ratings
Characteristic
Supply voltage, core
Supply voltage, IO
Supply voltage, analog
Symbol
Min
Max
Unit
VDD1
VSS – 0.3
VSS + 2.0
V
VDDIO2
VSSIO – 0.3
VSSA – 0.3
VSSIO + 4.0
VDDA + 4.0
V
VIN
VINA
VSSIO – 0.3
VSSA – 0.3
VSSIO + 5.5
VDDA + 0.3
V
I
—
8
mA
TJ
-40
120
°C
TSTG
-55
150
°C
VDDIO
Digital input voltages
Analog input voltages (XTAL, EXTAL)
Current drain per pin excluding VDD, GND
Junction temperature
Storage temperature range
2
1. VDD must not exceed VDDIO
2. VDDIO and VDDA must not differ by more that 0.5V
Table 4-2 Recommended Operating Conditions
Characteristic
Symbol
Min
Max
Unit
VDD
1.62
1.98
V
Supply voltage for I/O Power
VDDIO
3.0
3.6
V
Supply voltage for Analog Power
VDDA
3.0
3.6
V
Ambient operating temperature
TA
-40
85
°C
PLL clock frequency1
fpll
—
240
MHz
Operating Frequency2
fop
—
120
MHz
Frequency of peripheral bus
fipb
—
60
MHz
Supply voltage for Logic Power
56858 Technical Data, Rev. 6
Freescale Semiconductor
23
Table 4-2 Recommended Operating Conditions (Continued)
Characteristic
Symbol
Min
Max
Unit
Frequency of external clock
fclk
—
240
MHz
Frequency of oscillator
fosc
2
4
MHz
Frequency of clock via XTAL
fxtal
—
240
MHz
Frequency of clock via EXTAL
fextal
2
4
MHz
1. Assumes clock source is direct clock to EXTAL or crystal oscillator running 2-4MHz. PLL must be enabled, locked, and
selected. The actual frequency depends on the source clock frequency and programming of the CGM module.
2. Master clock is derived from on of the following four sources:
fclk = fxtal when the source clock is the direct clock to EXTAL
fclk = fpll when PLL is selected
fclk = fosc when the source clock is the crystal oscillator and PLL is not selected
fclk = fextal when the source clock is the direct clock to EXTAL and PLL is not selected
Table 4-3 Thermal Characteristics1
Value
Characteristic
Symbol
Unit
144-pin LQFP
144 MAPBGA
42.9
36.1
Thermal resistance junction-to-ambient
(estimated)
θJA
I/O pin power dissipation
PI/O
User Determined
W
Power dissipation
PD
PD = (IDD x VDD) + PI/O
W
PDMAX
(TJ - TA) / RθJA 2
W
Maximum allowed PD
°C/W
1. See Section 6.1 for more detail.
2. TJ = Junction Temperature
TA = Ambient Temperature
4.2 DC Electrical Characteristics
Table 4-4 DC Electrical Characteristics
Operating Conditions: VSS = VSSIO = VSSA = 0 V, VDD = 1.62-1.98V, VDDIO = VDDA = 3.0–3.6V, TA = –40° to +120°C, CL ≤ 50pF, fop = 120MHz
Characteristic
Symbol
Min
Typ
Max
Unit
Input high voltage (XTAL/EXTAL)
VIHC
VDDA – 0.8
VDDA
VDDA + 0.3
V
Input low voltage (XTAL/EXTAL)
VILC
-0.3
—
0.5
V
Input high voltage
VIH
2.0
—
5.5
V
Input low voltage
VIL
-0.3
—
0.8
V
56858 Technical Data, Rev. 6
24
Freescale Semiconductor
DC Electrical Characteristics
Table 4-4 DC Electrical Characteristics (Continued)
Operating Conditions: VSS = VSSIO = VSSA = 0 V, VDD = 1.62-1.98V, VDDIO = VDDA = 3.0–3.6V, TA = –40° to +120°C, CL ≤ 50pF, fop = 120MHz
Characteristic
Symbol
Min
Typ
Max
Unit
Input current low (pullups disabled)
IIL
-1
—
1
μA
Input current high (pullups disabled)
IIH
-1
—
1
μA
Output tri-state current low
IOZL
-10
—
10
μA
Output tri-state current high
IOZH
-10
—
10
μA
Output High Voltage
VOH
VDDIO – 0.7
—
—
V
Output Low Voltage
VOL
—
—
0.4
V
Output High Current
IOH
8
—
16
mA
Output Low Current
IOL
8
—
16
mA
Input capacitance
CIN
—
8
—
pF
Output capacitance
COUT
—
12
—
pF
VDD supply current (Core logic, memories, peripherals)
IDD4
—
—
—
70
0.05
5
110
10
14
mA
mA
mA
—
40
0
50
1.5
mA
mA
—
60
120
μA
1
Run
Deep Stop2
Light Stop3
VDDIO supply current (I/O circuity)
IDDIO
Run5
Deep
Stop2
VDDA supply current (analog circuity)
Deep
IDDA
Stop2
Low Voltage Interrupt6
VEI
—
2.5
2.85
V
Low Voltage Interrupt Recovery Hysteresis
VEIH
—
50
—
mV
Power on Reset7
POR
—
1.5
2.0
V
Note:
Run (operating) IDD measured using external square wave clock source (fosc = 4MHz) into XTAL. All inputs 0.2V from rail;
no DC loads; outputs unloaded. All ports configured as inputs; measured with all modules enabled. PLL set to 240MHz out.
1. Running Core, performing 50% NOP and 50% FIR. Clock at 120 MHz.
2. Deep Stop Mode - Operation frequency = 4 MHz, PLL set to 4 MHz, crystal oscillator and time of day module operating.
3. Light Stop Mode - Operation frequency = 120 MHz, PLL set to 240 MHz, crystal oscillator and time of day module operating.
4. IDD includes current for core logic, internal memories, and all internal peripheral logic circuitry.
5. Running core and performing external memory access. Clock at 120 MHz.
6. When VDD drops below VEI max value, an interrupt is generated.
7. Power-on reset occurs whenever the digital supply drops below 1.8V. While power is ramping up, this signal remains active
for as long as the internal 2.5V is below 1.8V no matter how long the ramp up rate is. The internally regulated voltage is
typically 100 mV less than VDD during ramp up until 2.5V is reached, at which time it self-regulates.
56858 Technical Data, Rev. 6
Freescale Semiconductor
25
150
EMI Mode5
MAC Mode1
120
IDD (mA)
90
60
30
0
20
40
60
80
120
100
Figure 4-1 Maximum Run IDDTOTAL vs. Frequency (see Notes 1. and 5. in Table 4-4)
4.3 Supply Voltage Sequencing and Separation Cautions
DC Power Supply Voltage
Figure 4-2 shows two situations to avoid in sequencing the VDD and VDDIO, VDDA supplies.
3.3V
VDDIO, VDDA
2
1.8V
Supplies Stable
VDD
1
0
Note:
Time
1. VDD rising before VDDIO, VDDA
2. VDDIO, VDDA rising much faster than VDD
Figure 4-2 Supply Voltage Sequencing and Separation Cautions
56858 Technical Data, Rev. 6
26
Freescale Semiconductor
AC Electrical Characteristics
VDD should not be allowed to rise early (1). This is usually avoided by running the regulator for the VDD
supply (1.8V) from the voltage generated by the 3.3V VDDIO supply, see Figure 4-3. This keeps VDD from
rising faster than VDDIO.
VDD should not rise so late that a large voltage difference is allowed between the two supplies (2).
Typically this situation is avoided by using external discrete diodes in series between supplies, as shown
in Figure 4-3. The series diodes forward bias when the difference between VDDIO and VDD reaches
approximately 2.1, causing VDD to rise as VDDIO ramps up. When the VDD regulator begins proper
operation, the difference between supplies will typically be 0.8V and conduction through the diode chain
reduces to essentially leakage current. During supply sequencing, the following general relationship
should be adhered to:
VDDIO > VDD > (VDDIO - 2.1V)
In practice, VDDA is typically connected directly to VDDIO with some filtering.
Supply
VDDIO, VDDA
3.3V
Regulator
VDD
1.8V
Regulator
Figure 4-3 Example Circuit to Control Supply Sequencing
4.4 AC Electrical Characteristics
Timing waveforms in Section 4.3 are tested with a VIL maximum of 0.8V and a VIH minimum of 2.0V for
all pins except XTAL, which is tested using the input levels in Section 4.2. In Figure 4-4 the levels of VIH
and VIL for an input signal are shown.
Low
VIH
Input Signal
High
90%
50%
10%
Midpoint1
VIL
Fall Time
Rise Time
Note: The midpoint is VIL + (VIH – VIL)/2.
Figure 4-4 Input Signal Measurement References
56858 Technical Data, Rev. 6
Freescale Semiconductor
27
Figure 4-5 shows the definitions of the following signal states:
•
•
•
Active state, when a bus or signal is driven, and enters a low impedance state
Tri-stated, when a bus or signal is placed in a high impedance state
Data Valid state, when a signal level has reached VOL or VOH
•
Data Invalid state, when a signal level is in transition between VOL and VOH
Data2 Valid
Data1 Valid
Data3 Valid
Data2
Data1
Data3
Data
Tri-stated
Data Invalid State
Data Active
Data Active
Figure 4-5 Signal States
4.5 External Clock Operation
The 56858 system clock can be derived from a crystal or an external system clock signal. To generate a
reference frequency using the internal oscillator, a reference crystal must be connected between the
EXTAL and XTAL pins.
4.5.1
Crystal Oscillator
The internal oscillator is designed to interface with a parallel-resonant crystal resonator in the frequency
range specified for the external crystal in Table 4-6. In Figure 4-6 a typical crystal oscillator circuit is
shown. Follow the crystal supplier’s recommendations when selecting a crystal, because crystal
parameters determine the component values required to provide maximum stability and reliable start-up.
The crystal and associated components should be mounted as close as possible to the EXTAL and XTAL
pins to minimize output distortion and start-up stabilization time.
Crystal Frequency = 2–4MHz (optimized for 4MHz)
EXTAL XTAL
Rz
Sample External Crystal Parameters:
Rz = 10MΩ
TOD_SEL bit in CGM must be set to 0
fc = 4MHz
fC
Figure 4-6 Crystal Oscillator
56858 Technical Data, Rev. 6
28
Freescale Semiconductor
External Clock Operation
4.5.2
High Speed External Clock Source (> 4MHz)
The recommended method of connecting an external clock is given in Figure 4-7. The external clock
source is connected to XTAL and the EXTAL pin is held at ground, VDDA, or VDDA/2. The TOD_SEL
bit in CGM must be set to 0.
56858
XTAL
EXTAL
GND,VDDA,
External
Clock
or VDDA/2
(up to 240MHz)
Figure 4-7 Connecting a High Speed External Clock Signal using XTAL
4.5.3
Low Speed External Clock Source (2-4MHz)
The recommended method of connecting an external clock is given in Figure 4-8. The external clock
source is connected to XTAL and the EXTAL pin is held at VDDA/2. The TOD_SEL bit in CGM must be
set to 0.
56858
XTAL
EXTAL
External
Clock
(2-4MHz)
VDDA/2
Figure 4-8 Connecting a Low Speed External Clock Signal using XTAL
Table 4-5 External Clock Operation Timing Requirements4
Operating Conditions: VSS = VSSIO = VSSA = 0 V, VDD = 1.62-1.98V, VDDIO = VDDA = 3.0–3.6V, TA = –40° to +120°C, CL ≤ 50pF, fop = 120MHz
Characteristic
Symbol
Min
Typ
Max
Unit
Frequency of operation (external clock driver)1
fosc
0
—
240
MHz
Clock Pulse Width4
tPW
6.25
—
—
ns
External clock input rise time2, 4
trise
—
—
TBD
ns
External clock input fall time3, 4
tfall
—
—
TBD
ns
1. See Figure 4-7 for details on using the recommended connection of an external clock driver.
2. External clock input rise time is measured from 10% to 90%.
3. External clock input fall time is measured from 90% to 10%.
4. Parameters listed are guaranteed by design.
56858 Technical Data, Rev. 6
Freescale Semiconductor
29
VIH
External
Clock
90%
50%
10%
tPW
90%
50%
10%
tPW
trise
tfall
VIL
Note: The midpoint is VIL + (VIH – VIL)/2.
Figure 4-9 External Clock Timing
Table 4-6 PLL Timing
Operating Conditions: VSS = VSSIO = VSSA = 0 V, VDD = 1.62-1.98V, VDDIO = VDDA = 3.0–3.6V, TA = –40° to +120°C, CL ≤ 50pF, fop = 120MHz
Characteristic
Symbol
Min
Typ
Max
Unit
External reference crystal frequency for the PLL1
fosc
2
4
4
MHz
PLL output frequency
fclk
40
—
240
MHz
PLL stabilization time 2
tplls
—
1
10
ms
1. An externally supplied reference clock should be as free as possible from any phase jitter for the PLL to work correctly.
The PLL is optimized for 4MHz input crystal.
2. This is the minimum time required after the PLL setup is changed to ensure reliable operation.
4.6 External Memory Interface Timing
The External Memory Interface is designed to access static memory and peripheral devices. Figure 4-10 shows
sample timing and parameters that are detailed in Table 4-7.
The timing of each parameter consists of both a fixed delay portion and a clock related portion; as well as user
controlled wait states. The equation:
t = D + P * (M + W)
should be used to determine the actual time of each parameter. The terms in the above equation are defined as:
t
parameter delay time
D fixed portion of the delay, due to on-chip path delays.
P
the period of the system clock, which determines the execution rate of the part (i.e. when the device is
operating at 120 MHz, P = 8.33 ns).
56858 Technical Data, Rev. 6
30
Freescale Semiconductor
External Memory Interface Timing
M Fixed portion of a clock period inherent in the design. This number is adjusted to account for possible
clock duty cycle derating.
W the sum of the applicable wait state controls. See the “Wait State Controls” column of Table 4-7 for
the applicable controls for each parameter. See the EMI chapter of the 83x Peripheral Manual for
details of what each wait state field controls.
Some of the parameters contain two sets of numbers. These parameters have two different paths and clock edges
that must be considered. Check both sets of numbers and use the smaller result. The appropriate entry may change
if the operating frequency of the part changes.
The timing of write cycles is different when WWS = 0 than when WWS > 0. Therefore, some parameters contain
two sets of numbers to account for this difference. The “Wait States Configuration” column of Table 4-7 should be
used to make the appropriate selection.
A0-Axx,CS
tRD
tARDD
tARDA
tRDA
tRDRD
RD
tWAC
tAWR
tWRWR
tWRRD
tWR
tRDWR
WR
tDWR
D0-D15
tDOS
tDOH
tAD
Data Out
tRDD
tDRD
Data In
Note: During read-modify-write instructions and internal instructions, the address lines do not change state.
Figure 4-10 External Memory Interface Timing
56858 Technical Data, Rev. 6
Freescale Semiconductor
31
Table 4-7 External Memory Interface Timing
Operating Conditions: VSS = VSSIO = VSSA = 0 V, VDD = 1.62-1.98 V, VDDIO = VDDA = 3.0–3.6V, TA = –40× to +120×C, CL £ 50pF, P = 8.333ns
Characteristic
Address Valid to WR Asserted
WR Width Asserted to WR
Deasserted
Symbol
tAWR
tWR
Data Out Valid to WR Asserted
tDWR
Wait States
Configuration
D
M
Wait States
Controls
Unit
WWS=0
-0.79
0.50
WWS>0
-1.98
0.69
WWSS
ns
WWS=0
-0.86
0.19
WWS>0
-0.01
0.00
WWS
ns
WWS=0
-1.52
0.00
WWS=0
- 5.69
0.25
WWS>0
-2.10
0.19
WWSS
ns
WWS>0
-4.66
0.50
-1.47
0.25
WWSH
ns
-2.36
0.19
-4.67
0.50
-1.60
0.25
WWSH
Valid Data Out Hold Time after WR
Deasserted
tDOH
Valid Data Out Set Up Time to WR
Deasserted
tDOS
Valid Address after WR
Deasserted
tWAC
RD Deasserted to Address Invalid
tRDA
- 0.44
0.00
RWSH
ns
Address Valid to RD Deasserted
tARDD
-2.07
1.00
RWSS,RWS
ns
Valid Input Data Hold after RD
Deasserted
tDRD
0.00
N/A1
—
ns
RD Assertion Width
tRD
-1.34
1.00
RWS
ns
Address Valid to Input Data Valid
tAD
-10.27
1.00
-13.5
1.19
RWSS,RWS
ns
- 0.94
0.00
RWSS
ns
-9.53
1.00
-12.64
1.19
RWSS,RWS
ns
Address Valid to RD Asserted
tARDA
RD Asserted to Input Data Valid
tRDD
WWS,WWSS
ns
WR Deasserted to RD Asserted
tWRRD
-0.75
0.25
WWSH,RWSS
ns
RD Deasserted to RD Asserted
tRDRD
-0.162
0.00
RWSS,RWSH
ns
WR Deasserted to WR Asserted
tWRWR
WWS=0
-0.44
0.75
WWS>0
-0.11
1.00
WWSS, WWSH
ns
0.14
0.50
-0.57
0.69
MDAR, BMDAR,
RWSH, WWSS
ns
RD Deasserted to WR Asserted
tRDWR
1. N/A since device captures data before it deasserts RD
2. If RWSS = RWSH = 0, RD does not deassert during back-to-back reads and D=0.00 should be used.
56858 Technical Data, Rev. 6
32
Freescale Semiconductor
Reset, Stop, Wait, Mode Select, and Interrupt Timing
4.7 Reset, Stop, Wait, Mode Select, and Interrupt Timing
Table 4-8 Reset, Stop, Wait, Mode Select, and Interrupt Timing1, 2
Operating Conditions: VSS = VSSIO = VSSA = 0 V, VDD = 1.62-1.98V, VDDIO = VDDA = 3.0–3.6V, TA = –40° to +120°C, CL ≤ 50pF, fop = 120MHz
Characteristic
Symbol
Min
Max
Unit
See Figure
RESET Assertion to Address, Data and Control
Signals High Impedance
tRAZ
—
11
ns
Figure 4-11
Minimum RESET Assertion Duration3
tRA
30
—
ns
Figure 4-11
RESET Deassertion to First External Address Output
tRDA
—
120T
ns
Figure 4-11
Edge-sensitive Interrupt Request Width
tIRW
1T + 3
—
ns
Figure 4-12
IRQA, IRQB Assertion to External Data Memory
Access Out Valid, caused by first instruction execution
in the interrupt service routine
tIDM
18T
—
ns
Figure 4-13
tIDM -FAST
14T
—
tIG
18T
—
ns
Figure 4-13
tIG -FAST
14T
—
tIRI
22T
—
ns
Figure 4-14
tIRI -FAST
18T
—
1.5T
—
IRQA, IRQB Assertion to General Purpose Output
Valid, caused by first instruction execution in the
interrupt service routine
IRQA Low to First Valid Interrupt Vector Address Out
recovery from Wait State4
Delay from IRQA Assertion (exiting Stop) to External
Data Memory5
tIW
Delay from IRQA Assertion (exiting Wait) to External
Data Memory
Fast6
Normal7
tIF
RSTO pulse width8
normal operation
internal reset mode
ns
Figure 4-15
Figure 4-15
18T
22ET
—
—
ns
ns
Figure 4-16
tRSTO
128ET
8ET
—
—
—
—
1. In the formulas, T = clock cycle. For fop = 120MHz operation and fipb = 60MHz, T = 8.33ns.
2. Parameters listed are guaranteed by design.
3. At reset, the PLL is disabled and bypassed. The part is then put into Run mode and tclk assumes the period of the source clock,
txtal, textal or tosc.
4. The minimum is specified for the duration of an edge-sensitive IRQA interrupt required to recover from the Stop state. This is not
the minimum required so that the IRQA interrupt is accepted.
5. The interrupt instruction fetch is visible on the pins only in Mode 3.
6. Fast stop mode:
Fast stop recovery applies when external clocking is in use (direct clocking to XTAL) or when fast stop mode recovery is
requested (OMR bit 6 is set to 1). In both cases the PLL and the master clock are unaffected by stop mode entry. Recovery takes
one less cycle and tclk will continue same value it had before stop mode was entered.
56858 Technical Data, Rev. 6
Freescale Semiconductor
33
7. Normal stop mode:
As a power saving feature, normal stop mode disables and bypasses the PLL. Stop mode will then shut down the master clock,
recovery will take an extra cycle (to restart the clock), and tclk will resume at the input clock source rate.
8. ET = External Clock period, For an external crystal frequency of 8MHz, ET=125 ns.
RESET
tRA
tRAZ
tRDA
A0–Axx,
D0–D15
First Fetch
CS,
RD, WR
First Fetch
Figure 4-11 Asynchronous Reset Timing
IRQA
IRQB
tIRW
Figure 4-12 External Interrupt Timing (Negative-Edge-Sensitive)
A0–Axx,
CS,
RD, WR
First Interrupt Instruction Execution
tIDM
IRQA,
IRQB
a) First Interrupt Instruction Execution
General
Purpose
I/O Pin
tIG
IRQA,
IRQB
b) General Purpose I/O
Figure 4-13 External Level-Sensitive Interrupt Timing
56858 Technical Data, Rev. 6
34
Freescale Semiconductor
Reset, Stop, Wait, Mode Select, and Interrupt Timing
IRQA,
IRQB
tIRI
A0–Axx,
CS,
RD, WR
First Interrupt Vector
Instruction Fetch
Figure 4-14 Interrupt from Wait State Timing
tIW
IRQA
tIF
A0–Axx,
CS,
RD, WR
First Instruction Fetch
Not IRQA Interrupt Vector
Figure 4-15 Recovery from Stop State Using Asynchronous Interrupt Timing
RESET
tRSTO
Figure 4-16 Reset Output Timing
56858 Technical Data, Rev. 6
Freescale Semiconductor
35
4.8 Host Interface Port
Table 4-9 Host Interface Port Timing1
Operating Conditions: VSS = VSSIO = VSSA = 0 V, VDD = 1.62-1.98V, VDDIO = VDDA = 3.0–3.6V, TA = –40° to +120°C, CL ≤ 50pF, fop = 120MHz
Characteristic
Symbol
Min
Max
Unit
See Figure
Access time
TACKDV
—
13
ns
4-17
Disable time
TACKDZ
3
—
ns
4-17
Time to disassert
TACKREQH
3.5
9
ns
4-17
4-20
Lead time
TREQACKL
0
—
ns
4-17
4-20
Access time
TRADV
—
13
Disable time
TRADX
5
—
Disable time
TRADZ
3
—
Setup time
TDACKS
3
Hold time
TACKDH
Setup time
ns
4-18
4-19
ns
4-18
4-19
ns
4-18
4-19
—
ns
4-20
1
—
ns
4-20
TADSS
3
—
ns
4-21
4-22
Hold time
TDSAH
1
—
ns
4-21
4-22
Pulse width
TWDS
5
—
ns
4-21
4-22
TACKREQL
4T + 5
5
5T + 9
13
ns
ns
4-19
4-20
Time to re-assert
1. After second write in 16-bit mode
2. After first write in 16-bit mode
or after write in 8-bit mode
1. The formulas: T = clock cycle. f ipb = 60MHz, T = 16.7ns.
56858 Technical Data, Rev. 6
36
Freescale Semiconductor
Host Interface Port
HACK
TACKDZ
TACKDV
HD
TREQACKL
TACKREQH
TACKREQL
HREQ
Figure 4-17 Controller-to-Host DMA Read Mode
HA
TRADX
HCS
HDS
HRW
TRADV
TRADZ
HD
Figure 4-18 Single Strobe Read Mode
56858 Technical Data, Rev. 6
Freescale Semiconductor
37
HA
TRADX
HCS
HWR
HRD
TRADZ
TRADV
HD
Figure 4-19 Dual Strobe Read Mode
HACK
TDACKS
TACKDH
HD
TREQACKL
TACKREQH
TACKREQL
HREQ
Figure 4-20 Host-to-Controller DMA Write Mode
56858 Technical Data, Rev. 6
38
Freescale Semiconductor
Host Interface Port
HA
TDSAH
HCS
TWDS
HDS
TDSAH
HRW
TADSS
TADSS
TDSAH
HD
Figure 4-21 Single Strobe Write Mode
HA
HCS
TWDS
HWR
TDSAH
TADSS
HRD
TADSS
HD
Figure 4-22 Dual Strobe Write Mode
56858 Technical Data, Rev. 6
Freescale Semiconductor
39
4.9 Serial Peripheral Interface (SPI) Timing
Figure 4-23 SPI Timing 1
Operating Conditions: VSS = VSSIO = VSSA = 0 V, VDD = 1.62-1.98V, VDDIO = VDDA = 3.0–3.6V, TA = –40° to +120°C, CL ≤ 50pF, fop = 120MHz
Characteristic
Symbol
Cycle time
Master
Slave
Min
Max
Unit
25
25
—
—
ns
ns
—
12.5
—
—
ns
ns
—
12.5
—
—
ns
ns
9
12.5
—
—
12
12.5
—
—
ns
ns
10
2
—
—
ns
ns
0
2
—
—
ns
ns
15
ns
ns
4-27
5
9
ns
ns
4-27
2
—
—
2
14
ns
ns
0
0
—
—
ns
ns
—
—
11.5
10.0
ns
ns
—
—
9.7
9.0
ns
ns
tC
Enable lead time
Master
Slave
tELD
Enable lag time
Master
Slave
tELG
Clock (SCLK) high time
Master
Slave
tCH
Clock (SCLK) low time
Master
Slave
tCL
Data set-up time required for inputs
Master
Slave
tDS
Data hold time required for inputs
Master
Slave
tDH
Access time (time to data active from high-impedance state)
Slave
tA
Disable time (hold time to high-impedance state)
Slave
tD
Data valid for outputs
Master
Slave (after enable edge)
tDV
Data invalid
Master
Slave
tDI
Rise time
Master
Slave
tR
Fall time
Master
Slave
tF
See Figure
4-24, 4-25,
4-26, 4-27
4-27
4-27
ns
ns
4-24, 4-25,
4-26, 4-27
4-27
4-24, 4-25,
4-26, 4-27
4-24, 4-25,
4-26, 4-27
4-24, 4-25,
4-26, 4-27
4-24, 4-25,
4-26, 4-27
4-24, 4-25,
4-26, 4-27
4-24, 4-25,
4-26, 4-27
1. Parameters listed are guaranteed by design.
56858 Technical Data, Rev. 6
40
Freescale Semiconductor
Serial Peripheral Interface (SPI) Timing
SS
SS is held High on master
(Input)
tC
tR
tF
tCL
SCLK (CPOL = 0)
(Output)
tCH
tF
tR
tCL
SCLK (CPOL = 1)
(Output)
tDH
tDS
tCH
MISO
(Input)
tCH
MSB in
Bits 14–1
tDI(ref)
tDV
tDI
MOSI
(Output)
LSB in
Master MSB out
Bits 14–1
Master LSB out
tR
tF
Figure 4-24 SPI Master Timing (CPHA = 0)
SS
(Input)
SS is held High on master
tC
tF
SCLK (CPOL = 0)
(Output)
tCH
tF
tCL
SCLK (CPOL = 1)
(Output)
tCH
MISO
(Input)
MSB in
tDS
tR
tDH
Bits 14–1
tDI
tDV(ref)
MOSI
(Output)
tR
tCL
Master MSB out
LSB in
tDV
Bits 14– 1
tF
Master LSB out
tR
Figure 4-25 SPI Master Timing (CPHA = 1)
56858 Technical Data, Rev. 6
Freescale Semiconductor
41
SS
(Input)
tC
tF
tR
tCL
SCLK (CPOL = 0)
(Input)
tELG
tCH
tELD
tCL
SCLK (CPOL = 1)
(Input)
tA
tCH
MISO
(Output)
Slave MSB out
tDS
tDH
MOSI
(Input)
MSB in
tF
tR
tD
Bits 14–1
Slave LSB out
tDV
tDI
Bits 14–1
tDI
LSB in
Figure 4-26 SPI Slave Timing (CPHA = 0)
SS
(Input)
tF
tC
tR
tCL
SCLK (CPOL = 0)
(Input)
tCH
tELG
tELD
SCLK (CPOL = 1)
(Input)
tCL
tDV
tA
MISO
(Output)
tF
tCH
Slave MSB out
tR
Bits 14–1
tDV
tDS
tD
Slave LSB out
tDI
tDH
MOSI
(Input)
MSB in
Bits 14–1
LSB in
Figure 4-27 SPI Slave Timing (CPHA = 1)
56858 Technical Data, Rev. 6
42
Freescale Semiconductor
Quad Timer Timing
4.10 Quad Timer Timing
Table 4-10 Quad Timer Timing1, 2
Operating Conditions: VSS = VSSIO = VSSA = 0 V, VDD = 1.62-1.98V, VDDIO = VDDA = 3.0–3.6V, TA = –40° to +120°C, CL ≤ 50pF, fop = 120MHz
Characteristic
Symbol
Min
Max
Unit
PIN
2T + 3
—
ns
Timer input high/low period
PINHL
1T + 3
—
ns
Timer output period
POUT
2T - 3
—
ns
POUTHL
1T - 3
—
ns
Timer input period
Timer output high/low period
1. In the formulas listed, T = clock cycle. For fop = 120MHz operation and fipb = 60MHz, T = 8.33ns.
2. Parameters listed are guaranteed by design.
Timer Inputs
PIN
PINHL
PINHL
POUT
POUTHL
POUTHL
Timer Outputs
Figure 4-28 Timer Timing
4.11 Enhanced Synchronous Serial Interface (ESSI) Timing
Table 4-11 ESSI Master Mode1 Switching Characteristics
Operating Conditions: VSS = VSSIO = VSSA = 0 V, VDD = 1.62-1.98V, VDDIO = VDDA = 3.0–3.6V, TA = –40° to +120°C, CL ≤ 50pF, fop = 120MHz
Parameter
Symbol
Min
Typ
fs
—
SCK period3
tSCKW
SCK high time
SCK low time
SCK frequency
Output clock rise/fall time
Delay from SCK high to SC2 (bl) high - Master5
Max
Units
—
152
MHz
66.7
—
—
ns
tSCKH
33.44
—
—
ns
tSCKL
33.44
—
—
ns
—
—
4
—
ns
tTFSBHM
-1.0
—
1.0
ns
56858 Technical Data, Rev. 6
Freescale Semiconductor
43
Table 4-11 ESSI Master Mode1 Switching Characteristics (Continued)
Operating Conditions: VSS = VSSIO = VSSA = 0 V, VDD = 1.62-1.98V, VDDIO = VDDA = 3.0–3.6V, TA = –40° to +120°C, CL ≤ 50pF, fop = 120MHz
Parameter
Symbol
Min
Typ
Max
Units
Delay from SCK high to SC2 (wl) high - Master5
tTFSWHM
-1.0
—
1.0
ns
Delay from SC0 high to SC1 (bl) high - Master5
tRFSBHM
-1.0
—
1.0
ns
Delay from SC0 high to SC1 (wl) high - Master5
tRFSWHM
-1.0
—
1.0
ns
Delay from SCK high to SC2 (bl) low - Master5
tTFSBLM
-1.0
—
1.0
ns
Delay from SCK high to SC2 (wl) low - Master5
tTFSWLM
-1.0
—
1.0
ns
Delay from SC0 high to SC1 (bl) low - Master5
tRFSBLM
-1.0
—
1.0
ns
Delay from SC0 high to SC1 (wl) low - Master5
tRFSWLM
-1.0
—
1.0
ns
SCK high to STD enable from high impedance - Master
tTXEM
-0.1
—
2
ns
SCK high to STD valid - Master
tTXVM
-0.1
—
2
ns
SCK high to STD not valid - Master
tTXNVM
-0.1
—
—
ns
SCK high to STD high impedance - Master
tTXHIM
-4
—
0
ns
SRD Setup time before SC0 low - Master
tSM
4
—
—
ns
SRD Hold time after SC0 low - Master
tHM
4
—
—
ns
Synchronous Operation (in addition to standard internal clock parameters)
SRD Setup time before SCK low - Master
tTSM
4
—
—
ns
SRD Hold time after SCK low - Master
tTHM
4
—
—
ns
1. Master mode is internally generated clocks and frame syncs
2. Max clock frequency is IP_clk/4 = 60MHz / 4 = 15MHz for an 120MHz part.
3. All the timings for the ESSI are given for a non-inverted serial clock polarity (TSCKP=0 in SCR2 and RSCKP=0 in SCSR)
and a non-inverted frame sync (TFSI=0 in SCR2 and RFSI=0 in SCSR). If the polarity of the clock and/or the frame sync
have been inverted, all the timings remain valid by inverting the clock signal SCK/SC0 and/or the frame sync SC2/SC1 in
the tables and in the figures.
4. 50 percent duty cycle
5. bl = bit length; wl = word length
56858 Technical Data, Rev. 6
44
Freescale Semiconductor
Enhanced Synchronous Serial Interface (ESSI) Timing
tSCKH
tSCKW
tSCKL
SCK output
tTFSBHM
tTFSBLM
SC2 (bl) output
tTFSWHM
tTFSWLM
SC2 (wl) output
tTXVM
tTXEM
tTXNVM
tTXHIM
First Bit
STD
Last Bit
SC0 output
tRFSBHM
tRFBLM
SC1 (bl) output
tRFSWHM
tRFSWLM
SC1 (wl) output
tSM
tHM
tTSM
tTHM
SRD
Figure 4-29 Master Mode Timing Diagram
Table 4-12 ESSI Slave Mode1 Switching Characteristics
Operating Conditions: VSS = VSSIO = VSSA = 0 V, VDD = 1.62-1.98V, VDDIO = VDDA = 3.0–3.6V, TA = –40° to +120°C, CL ≤ 50pF, fop = 120MHz
Parameter
Symbol
Min
Typ
Max
Units
fs
—
—
152
MHz
SCK period3
tSCKW
66.7
—
—
ns
SCK high time
tSCKH
33.44
—
—
ns
SCK low time
tSCKL
33.44
—
—
ns
—
—
4
—
ns
SCK frequency
Output clock rise/fall time
56858 Technical Data, Rev. 6
Freescale Semiconductor
45
Table 4-12 ESSI Slave Mode1 Switching Characteristics (Continued)
Operating Conditions: VSS = VSSIO = VSSA = 0 V, VDD = 1.62-1.98V, VDDIO = VDDA = 3.0–3.6V, TA = –40° to +120°C, CL ≤ 50pF, fop = 120MHz
Parameter
Symbol
Min
Typ
Max
Units
Delay from SCK high to SC2 (bl) high - Slave5
tTFSBHS
-1
—
29
ns
Delay from SCK high to SC2 (wl) high - Slave5
tTFSWHS
-1
—
29
ns
Delay from SC0 high to SC1 (bl) high - Slave5
tRFSBHS
-1
—
29
ns
Delay from SC0 high to SC1 (wl) high - Slave5
tRFSWHS
-1
—
29
ns
Delay from SCK high to SC2 (bl) low - Slave5
tTFSBLS
-29
—
29
ns
Delay from SCK high to SC2 (wl) low - Slave5
tTFSWLS
-29
—
29
ns
Delay from SC0 high to SC1 (bl) low - Slave5
tRFSBLS
-29
—
29
ns
Delay from SC0 high to SC1 (wl) low - Slave5
tRFSWLS
-29
—
29
ns
SCK high to STD enable from high impedance - Slave
tTXES
—
—
15
ns
SCK high to STD valid - Slave
tTXVS
4
—
15
ns
SC2 high to STD enable from high impedance (first bit) - Slave
tFTXES
4
—
15
ns
SC2 high to STD valid (first bit) - Slave
tFTXVS
4
—
15
ns
SCK high to STD not valid - Slave
tTXNVS
4
—
15
ns
SCK high to STD high impedance - Slave
tTXHIS
4
—
15
ns
SRD Setup time before SC0 low - Slave
tSS
4
—
—
ns
SRD Hold time after SC0 low - Slave
tHS
4
—
—
ns
Synchronous Operation (in addition to standard external clock parameters)
SRD Setup time before SCK low - Slave
tTSS
4
—
—
ns
SRD Hold time after SCK low - Slave
tTHS
4
—
—
ns
1. Slave mode is externally generated clocks and frame syncs
2. Max clock frequency is IP_clk/4 = 60MHz / 4 = 15MHz for a 120MHz part.
3. All the timings for the ESSI are given for a non-inverted serial clock polarity (TSCKP=0 in SCR2 and RSCKP=0 in SCSR)
and a non-inverted frame sync (TFSI=0 in SCR2 and RFSI=0 in SCSR). If the polarity of the clock and/or the frame sync
have been inverted, all the timings remain valid by inverting the clock signal SCK/SC0 and/or the frame sync SC2/SC1 in
the tables and in the figures.
4. 50 percent duty cycle
5. bl = bit length; wl = word length
56858 Technical Data, Rev. 6
46
Freescale Semiconductor
Enhanced Synchronous Serial Interface (ESSI) Timing
tSCKW
tSCKH
tSCKL
SCK input
tTFSBLS
tTFSBHS
SC2 (bl) input
tTFSWHS
tTFSWLS
SC2 (wl) input
tFTXVS
tFTXES
tTXNVS
tTXVS
tTXES
tTXHIS
First Bit
STD
SC0 input
Last Bit
tRFBLS
tRFSBHS
SC1 (bl) input
tRFSWHS
tRFSWLS
SC1 (wl) input
tSS
tHS
tTSS
tTHS
SRD
Figure 4-30 Slave Mode Clock Timing
56858 Technical Data, Rev. 6
Freescale Semiconductor
47
4.12 Serial Communication Interface (SCI) Timing
Table 4-13 SCI Timing4
Operating Conditions: VSS = VSSIO = VSSA = 0 V, VDD = 1.62-1.98V, VDDIO = VDDA = 3.0–3.6V, TA = –40° to +120°C, CL ≤ 50pF, fop = 120MHz
Characteristic
Symbol
Min
Max
Unit
BR
—
(fMAX)/(32)
Mbps
RXD2 Pulse Width
RXDPW
0.965/BR
1.04/BR
ns
TXD3 Pulse Width
TXDPW
0.965/BR
1.04/BR
ns
Baud Rate1
1. fMAX is the frequency of operation of the system clock in MHz.
2. The RXD pin in SCI0 is named RXD0 and the RXD pin in SCI1 is named RXD1.
3. The TXD pin in SCI0 is named TXD0 and the TXD pin in SCI1 is named TXD1.
4. Parameters listed are guaranteed by design.
RXD
SCI receive
data pin
(Input)
RXDPW
Figure 4-31 RXD Pulse Width
TXD
SCI receive
data pin
(Input)
TXDPW
Figure 4-32 TXD Pulse Width
56858 Technical Data, Rev. 6
48
Freescale Semiconductor
JTAG Timing
4.13 JTAG Timing
Table 4-14 JTAG Timing1, 3
Operating Conditions: VSS = VSSIO = VSSA = 0 V, VDD = 1.62-1.98V, VDDIO = VDDA = 3.0–3.6V, TA = –40° to +120°C, CL ≤ 50pF, fop = 120MHz
Characteristic
Symbol
Min
Max
Unit
TCK frequency of operation2
fOP
DC
30
MHz
TCK cycle time
tCY
33.3
—
ns
TCK clock pulse width
tPW
16.6
—
ns
TMS, TDI data setup time
tDS
3
—
ns
TMS, TDI data hold time
tDH
3
—
ns
TCK low to TDO data valid
tDV
—
12
ns
TCK low to TDO tri-state
tTS
—
10
ns
tTRST
35
—
ns
tDE
4T
—
ns
TRST assertion time
DE assertion time
1. Timing is both wait state and frequency dependent. For the values listed, T = clock cycle. For 120MHz operation,
T = 8.33ns.
2. TCK frequency of operation must be less than 1/4 the processor rate.
3. Parameters listed are guaranteed by design.
tCY
tPW
tPW
VIH
VM
TCK
(Input)
VM = VIL + (VIH – VIL)/2
VM
VIL
Figure 4-33 Test Clock Input Timing Diagram
56858 Technical Data, Rev. 6
Freescale Semiconductor
49
TCK
(Input)
tDS
TDI
TMS
(Input)
tDH
Input Data Valid
tDV
TDO
(Output)
Output Data Valid
tTS
TDO
(Output)
Figure 4-34 Test Access Port Timing Diagram
TRST
(Input)
tTRST
Figure 4-35 TRST Timing Diagram
DE
tDE
Figure 4-36 Enhanced OnCE—Debug Event
56858 Technical Data, Rev. 6
50
Freescale Semiconductor
GPIO Timing
4.14 GPIO Timing
Table 4-15 GPIO Timing1, 2
Operating Conditions: VSS = VSSIO = VSSA = 0 V, VDD = 1.62-1.98V, VDDIO = VDDA = 3.0–3.6V, TA = –40° to +120°C, CL ≤ 50pF, fop = 120MHz
Characteristic
Symbol
Min
Max
Unit
PIN
2T + 3
—
ns
GPIO input high/low period
PINHL
1T + 3
—
ns
GPIO output period
POUT
2T - 3
—
ns
POUTHL
1T - 3
—
ns
GPIO input period
GPIO output high/low period
1. In the formulas listed, T = clock cycle. For fop = 120MHz operation and fipb = 60MHz, T = 8.33ns
2. Parameters listed are guaranteed by design.
GPIO Inputs
PIN
PINHL
PINHL
POUT
POUTHL
POUTHL
GPIO Outputs
Figure 4-37 GPIO Timing
56858 Technical Data, Rev. 6
Freescale Semiconductor
51
Part 5 Packaging
5.1 Package and Pin-Out Information 56853
D15
D14
D13
VSSIO
VSSIO
VDDIO
D12
D11
SC02
SC01
SC00
SCK0
SRD0
STD0
VSSIO
VDDIO
VSSIO
VSS
VSS
VDD
D10
D9
D8
D7
D6
HACK
HREQ
HCS
HDS
VSSIO
TIO0
VDDIO
TIO1
TIO2
TIO3
VDD
This section contains package and pin-out information for the 144-pin LQFP configuration of the 56858.
MISO
MOSI
SCK
SS
VDDIO
VDDIO
VSSIO
Orientation Mark
PIN 109
PIN 1
RD
WR
A0
A1
A2
A3
VDD
VSS
VSS
MODA
MODB
MODC
VDDIO
VSSIO
IRQA
IRQB
VDDA
VSSA
VSSA
PIN 37
PIN 73
CS3
CS2
CS1
CS0
VSSIO
D0
VDDIO
A20
A19
A18
A17
A16
TXD0
RXD0
CLKO
RSTO
RESET
HD3
HD4
HD5
HD6
HD7
VDDIO
VSSIO
VSSIO
A8
A9
A10
A11
VDD
VSS
VSS
DE
TRST
TDO
TDI
TMS
TCK
VDDIO
VSSIO
A12
A13
A14
A15
VDDIO
VDDIO
VSSIO
VSSIO
VSS
VDD
XTAL
EXTAL
A4
A5
A6
A7
HD0
HD1
HD2
VDD
TXD1
RXD1
VSSIO
VDDIO
SC12
SC11
SC10
SCK1
SRD1
STD1
D5
D4
D3
D2
D1
HRWB
HA2
HA1
HA0
VSS
VDD
VDD
Figure 5-1 Top View, 56858 144-pin LQFP Package
56858 Technical Data, Rev. 6
52
Freescale Semiconductor
Package and Pin-Out Information 56853
Table 5-1 56858 Pin Identification by Pin Number
Pin
No.
Signal Name
Pin
No.
Signal Name
Pin
No.
Signal Name
Pin
No.
Signal Name
1
MISO
37
CLKO
73
RXD0
109
VDD
2
MOSI
38
RSTO
74
TXD0
110
TIO3
3
SCK
39
RESET
75
A16
111
TIO2
4
SS
40
HD3
76
A17
112
TIO1
5
VDDIO
41
HD4
77
A18
113
VDDIO
6
VDDIO
42
HD5
78
A19
114
TIO0
7
VSSIO
43
HD6
79
A20
115
VSSIO
8
RD
44
HD7
80
VDDIO
116
HDS
9
WR
45
VDDIO
81
D0
117
HCS
10
A0
46
VSSIO
82
VSSIO
118
HREQ
11
A1
47
VSSIO
83
CS0
119
HACK
12
A2
48
A8
84
CS1
120
D6
13
A3
49
A9
85
CS2
121
D7
14
VDD
50
A10
86
CS3
122
D8
15
VSS
51
A11
87
VDD
123
D9
16
VSS
52
VDD
88
VDD
124
D10
17
MODA
53
VSS
89
VSS
125
VDD
18
MODB
54
VSS
90
HA0
126
VSS
19
MODC
55
DE
91
HA1
127
VSS
20
VDDIO
56
TRST
92
HA2
128
VSSIO
21
VSSIO
57
TDO
93
HRWB
129
VDDIO
22
IRQA
58
TDI
94
D1
130
VSSIO
23
IRQB
59
TMS
95
D2
131
STD0
56858 Technical Data, Rev. 6
Freescale Semiconductor
53
Table 5-1 56858 Pin Identification by Pin Number (Continued)
Pin
No.
Signal Name
Pin
No.
Signal Name
Pin
No.
Signal Name
Pin
No.
Signal Name
24
VDDA
60
TCK
96
D3
132
SRD0
25
VSSA
61
VDDIO
97
D4
133
SCK0
26
VSSA
62
VSSIO
98
D5
134
SC00
27
XTAL
63
A12
99
STD1
135
SC01
28
EXTAL
64
A13
100
SRD1
136
SC02
29
A4
65
A14
101
SCK1
137
D11
30
A5
66
A15
102
SC10
138
D12
31
A6
67
VDDIO
103
SC11
139
VDDIO
32
A7
68
VDDIO
104
SC12
140
VSSIO
33
HD0
69
VSSIO
105
VDDIO
141
VSSIO
34
HD1
70
VSSIO
106
VSSIO
142
D13
35
HD2
71
VSS
107
RXD1
143
D14
36
VDD
72
VDD
108
TXD1
144
D15
56858 Technical Data, Rev. 6
54
Freescale Semiconductor
Package and Pin-Out Information 56853
Figure 5-2 144-pin LQFP Mechanical Information
Please see www.freescale.com for the most current case outline.
56858 Technical Data, Rev. 6
Freescale Semiconductor
55
This section contains package and pin-out information for the 144-pin MAPBGA configuration of the 56858.
METALLIZED MARK FOR
PIN 1 IDENTIFICATION
IN THIS AREA
12
11
10
9
8
7
6
5
4
VDD
VDDIO
VSSIO
VDD
VSS
VSS
VSSIO
VDDIO
VSSIO
VSSIO
RXD1
TIO3
TIO0
HREQ
D7
STD0
SC01
VDDIO
SC12
TXD1
TIO1
HDS
HACK
SRD0
VSS
SC11
SC10
TIO2
HCS
D6
VDD
SRD1
D5
SCK1
STD10
D8
2
1
VDDIO
VSSIO
VSSIO
D12
D15
MISO
VDDIO
SCK0
D13
MOSI
SCK
VDDIO
SC00
D11
WR
RD
SS
VSSIO
SC02
A0
A1
A2
A3
VDD
3
A
B
C
D
E
F
VDD
D4
D3
D2
D9
D10
D14
IRQB
MODA
MODB
MODC
VSS
G
VSSIO
HA1
HA0
HA2
HRWB
D1
TDO
A8
A6
EXTAL
IRQA
VSS
VDDIO
CS2
CS3
CS1
CS0
D0
DE
HD7
A7
A5
XTAL
VDDIO
VDD
A20
A19
A18
A12
TMS
A10
HD5
HD3
HD0
A4
VSSIO
VSS
A17
A16
A15
A13
TDI
A11
HD6
RESET
RSTO
HD1
VDDA
VSSIO
TXD0
RXD0
A14
TCK
TRST
VSS
A9
HD4
CLKO
HD2
VSSA
VSS10
VDDIO
VDDIO
VSSIO
VDDIO
VSS
VDD
VSSIO
VSSIO
VDD
VSSA
H
J
K
L
VDDIO
M
Figure 5-3 Bottom-View, 56858 144-pin MAPBGA Package
56858 Technical Data, Rev. 6
56
Freescale Semiconductor
Package and Pin-Out Information 56853
Table 5-2 56858 Pin Identification by Pin Number
Pin No.
Signal Name
Pin No.
Signal Name
Pin No.
Signal Name
Pin No.
Signal Name
E5
A0
F7
D10
D8
HCS
A5
VDDIO
E4
A1
D5
D11
J3
HD0
A3
VDDIO
E3
A2
B4
D12
K2
HD1
C1
VDDIO
E2
A3
C4
D13
L2
HD2
M10
VDDIO
J2
A4
F6
D14
J4
HD3
D3
RD
H3
A5
B3
D15
L4
HD4
K4
RESET
G4
A6
H6
DE
J5
HD5
K3
RSTO
H4
A7
G3
EXTAL
K5
HD6
L10
RXD0
G5
A8
M1
VSSA
H5
HD7
B11
RXD1
L5
A9
L1
VSSA
C8
HDS
D6
SC00
J6
A10
G1
VSS
B8
HREQ
B5
SC01
K6
A11
L6
VSS
G8
HRWB
E6
SC02
J8
A12
D12
VSS
G2
IRQA
D10
SC10
K8
A13
A7
VSS
F5
IRQB
D11
SC11
L9
A14
F1
VSS
B2
MISO
C11
SC12
K9
A15
M7
VSS
F4
MODA
C5
SCK0
K10
A16
K12
VSS
F3
MODB
E9
SCK1
K11
A17
A8
VSS
F2
MODC
C2
SCK
J9
A18
D1
VSSIO
C3
MOSI
C6
SRD0
J10
A19
J1
VSSIO
K1
VDDA
E11
SRD1
J11
A20
M5
VSSIO
E1
VDD
D2
SS
L3
CLKO
M9
VSSIO
M6
VDD
B6
STD0
H8
CS0
L12
VSSIO
F12
VDD
E8
STD1
H9
CS1
G12
VSSIO
A9
VDD
L8
TCK
56858 Technical Data, Rev. 6
Freescale Semiconductor
57
Table 5-2 56858 Pin Identification by Pin Number (Continued)
Pin No.
Signal Name
Pin No.
Signal Name
Pin No.
Signal Name
Pin No.
Signal Name
H11
CS2
B12
VSSIO
M2
VDD
K7
TDI
H10
CS3
A10
VSSIO
J12
VDD
G6
TDO
H7
D0
A4
VSSIO
E12
VDD
B9
TIO0
G7
D1
A1
VSSIO
A12
VDD
C9
TIO1
F9
D2
A2
VSSIO
B1
VDDIO
D9
TIO2
F10
D3
M4
VSSIO
H1
VDDIO
B10
TIO3
F11
D4
M12
VSSIO
M3
VDDIO
J7
TMS
E10
D5
A6
VSSIO
M8
VDDIO
L7
TRST
D7
D6
G10
HA0
M11
VDDIO
L11
TXD0
B7
D7
G11
HA1
H12
VDDIO
C10
TXD1
E7
D8
G9
HA2
C12
VDDIO
D4
WR
F8
D9
C7
HACK
A11
VDDIO
H2
XTAL
56858 Technical Data, Rev. 6
58
Freescale Semiconductor
Package and Pin-Out Information 56853
D
X
LASER MARK FOR PIN 1
IDENTIFICATION IN
THIS AREA
Y
Detail K
M
NOTES:
1. DIMENSIONS ARE IN MILLIMETERS.
2. INTERPRET DIMENSIONS AND
TOLERANCES PER ASME Y14.5M, 1994.
3. DIMENSION b IS MEASURED AT THE
MAXIMUM SOLDER BALL DIAMETER,
PARALLEL TO DATUM PLANE Z.
4. DATUM Z (SEATING PLANE) IS DEFINED BY
THE SPHERICAL CROWNS OF THE SOLDER
BALLS.
5. PARALLELISM MEASUREMENT SHALL
EXCLUDE ANY EFFECT OF MARK ON TOP
SURFACE OF PACKAGE.
E
0.20
MILLIMETERS
DIM MIN MAX
A
--1.60
A1
0.27
0.47
A2
1.16 REF
b
0.40
0.60
D
13.00 BSC
E
13.00 BSC
e
1.00 BSC
S
0.50 BSC
S
11X
e
12 11 10 9
8
5
4
3
2
METALIZED MARK FOR
PIN 1 IDENTIFICATION
IN THIS AREA
1
A
B
C
D
e
11X
E
5
F
G
H
S
A
0.20 Z
A2
J
K
A1
Z
4
0.12 Z
L
M
3
144X
b
0.25
0.10
Z X Y
DETAIL K
ROTATED 90 ° CLOCKWISE
VIEW M-M
Z
Figure 5-4 144-pin MAPBGA Mechanical Information
Please see www.freescale.com for the most current case outline.
56858 Technical Data, Rev. 6
Freescale Semiconductor
59
Part 6 Design Considerations
6.1 Thermal Design Considerations
An estimation of the chip junction temperature, TJ, in °C can be obtained from the equation:
Equation 1:
TJ = TA + (PD x RθJA)
Where:
TA = ambient temperature °C
RθJA = package junction-to-ambient thermal resistance °C/W
PD = power dissipation in package
Historically, thermal resistance has been expressed as the sum of a junction-to-case thermal resistance and
a case-to-ambient thermal resistance:
Equation 2:
RθJA = RθJC + RθCA
Where:
RθJA = package junction-to-ambient thermal resistance °C/W
RθJC = package junction-to-case thermal resistance °C/W
RθCA = package case-to-ambient thermal resistance °C/W
RθJC is device-related and cannot be influenced by the user. The user controls the thermal environment to
change the case-to-ambient thermal resistance, RθCA. For example, the user can change the air flow around
the device, add a heat sink, change the mounting arrangement on the Printed Circuit Board (PCB), or
otherwise change the thermal dissipation capability of the area surrounding the device on the PCB. This
model is most useful for ceramic packages with heat sinks; some 90% of the heat flow is dissipated through
the case to the heat sink and out to the ambient environment. For ceramic packages, in situations where
the heat flow is split between a path to the case and an alternate path through the PCB, analysis of the
device thermal performance may need the additional modeling capability of a system level thermal
simulation tool.
The thermal performance of plastic packages is more dependent on the temperature of the PCB to which
the package is mounted. Again, if the estimations obtained from RθJA do not satisfactorily answer whether
the thermal performance is adequate, a system level model may be appropriate.
A complicating factor is the existence of three common definitions for determining the junction-to-case
thermal resistance in plastic packages:
•
•
•
Measure the thermal resistance from the junction to the outside surface of the package (case) closest to the
chip mounting area when that surface has a proper heat sink. This is done to minimize temperature variation
across the surface.
Measure the thermal resistance from the junction to where the leads are attached to the case. This definition
is approximately equal to a junction to board thermal resistance.
Use the value obtained by the equation (TJ – TT)/PD where TT is the temperature of the package case
determined by a thermocouple.
56858 Technical Data, Rev. 6
60
Freescale Semiconductor
Electrical Design Considerations
As noted above, the junction-to-case thermal resistances quoted in this data sheet are determined using the
first definition. From a practical standpoint, that value is also suitable for determining the junction
temperature from a case thermocouple reading in forced convection environments. In natural convection,
using the junction-to-case thermal resistance to estimate junction temperature from a thermocouple
reading on the case of the package will estimate a junction temperature slightly hotter than actual. Hence,
the new thermal metric, Thermal Characterization Parameter, or ΨJT, has been defined to be (TJ – TT)/PD.
This value gives a better estimate of the junction temperature in natural convection when using the surface
temperature of the package. Remember that surface temperature readings of packages are subject to
significant errors caused by inadequate attachment of the sensor to the surface and to errors caused by heat
loss to the sensor. The recommended technique is to attach a 40-gauge thermocouple wire and bead to the
top center of the package with thermally conductive epoxy.
6.2 Electrical Design Considerations
CAUTION
This device contains protective circuitry to guard against
damage due to high static voltage or electrical fields.
However, normal precautions are advised to avoid
application of any voltages higher than maximum rated
voltages to this high-impedance circuit. Reliability of
operation is enhanced if unused inputs are tied to an
appropriate voltage level.
Use the following list of considerations to assure correct operation:
•
Provide a low-impedance path from the board power supply to each VDD pin on the controller, and from the
board ground to each VSS (GND) pin.
•
The minimum bypass requirement is to place six 0.01–0.1 μF capacitors positioned as close as possible to
the package supply pins. The recommended bypass configuration is to place one bypass capacitor on each
of the ten VDD/VSS pairs, including VDDA/VSSA.
•
Ensure that capacitor leads and associated printed circuit traces that connect to the chip VDD and VSS (GND)
pins are less than 0.5 inch per capacitor lead.
Use at least a four-layer Printed Circuit Board (PCB) with two inner layers for VDD and GND.
•
•
•
•
Bypass the VDD and GND layers of the PCB with approximately 100 μF, preferably with a high-grade
capacitor such as a tantalum capacitor.
Because the device’s output signals have fast rise and fall times, PCB trace lengths should be minimal.
Consider all device loads as well as parasitic capacitance due to PCB traces when calculating capacitance.
This is especially critical in systems with higher capacitive loads that could create higher transient currents
in the VDD and GND circuits.
56858 Technical Data, Rev. 6
Freescale Semiconductor
61
•
•
All inputs must be terminated (i.e., not allowed to float) using CMOS levels.
Take special care to minimize noise levels on the VDDA and VSSA pins.
•
•
When using Wired-OR mode on the SPI or the IRQx pins, the user must provide an external pull-up device.
Designs that utilize the TRST pin for JTAG port or Enhance OnCE module functionality (such as
development or debugging systems) should allow a means to assert TRST whenever RESET is asserted, as
well as a means to assert TRST independently of RESET. Designs that do not require debugging
functionality, such as consumer products, should tie these pins together.
The internal POR (Power on Reset) will reset the part at power on with reset asserted or pulled high but
requires that TRST be asserted at power on.
•
56858 Technical Data, Rev. 6
62
Freescale Semiconductor
Electrical Design Considerations
Part 7 Ordering Information
Table 7-1 lists the pertinent information needed to place an order. Consult a Freescale Semiconductor
sales office or authorized distributor to determine availability and to order parts.
Table 7-1 56858 Ordering Information
Part
Supply
Voltage
Pin
Count
Frequency
(MHz)
Order Number
DSP56858
1.8V, 3.3V
Low-Profile Quad Flat Pack (LQFP)
144
120
DSP56858FV120
DSP56858
1.8V, 3.3V
MAP Ball Grid Array (MAPBGA)
144
120
DSP56858VF120
DSP56858
1.8V, 3.3V
Low-Profile Quad Flat Pack (LQFP)
144
120
DSP56858FVE *
Package Type
*This package is RoHS compliant.
56858 Technical Data, Rev. 6
Freescale Semiconductor
63
How to Reach Us:
Home Page:
www.freescale.com
E-mail:
[email protected]
USA/Europe or Locations Not Listed:
Freescale Semiconductor
Technical Information Center, CH370
1300 N. Alma School Road
Chandler, Arizona 85224
+1-800-521-6274 or +1-480-768-2130
[email protected]
Europe, Middle East, and Africa:
Freescale Halbleiter Deutschland GmbH
Technical Information Center
Schatzbogen 7
81829 Muenchen, Germany
+44 1296 380 456 (English)
+46 8 52200080 (English)
+49 89 92103 559 (German)
+33 1 69 35 48 48 (French)
[email protected]
Japan:
Freescale Semiconductor Japan Ltd.
Headquarters
ARCO Tower 15F
1-8-1, Shimo-Meguro, Meguro-ku,
Tokyo 153-0064, Japan
0120 191014 or +81 3 5437 9125
[email protected]
Asia/Pacific:
Freescale Semiconductor Hong Kong Ltd.
Technical Information Center
2 Dai King Street
Tai Po Industrial Estate
Tai Po, N.T., Hong Kong
+800 2666 8080
[email protected]
For Literature Requests Only:
Freescale Semiconductor Literature Distribution Center
P.O. Box 5405
Denver, Colorado 80217
1-800-441-2447 or 303-675-2140
Fax: 303-675-2150
[email protected]
Information in this document is provided solely to enable system and
software implementers to use Freescale Semiconductor products. There are
no express or implied copyright licenses granted hereunder to design or
fabricate any integrated circuits or integrated circuits based on the
information in this document.
Freescale Semiconductor reserves the right to make changes without further
notice to any products herein. Freescale Semiconductor makes no warranty,
representation or guarantee regarding the suitability of its products for any
particular purpose, nor does Freescale Semiconductor assume any liability
arising out of the application or use of any product or circuit, and specifically
disclaims any and all liability, including without limitation consequential or
incidental damages. “Typical” parameters that may be provided in Freescale
Semiconductor data sheets and/or specifications can and do vary in different
applications and actual performance may vary over time. All operating
parameters, including “Typicals”, must be validated for each customer
application by customer’s technical experts. Freescale Semiconductor does
not convey any license under its patent rights nor the rights of others.
Freescale Semiconductor products are not designed, intended, or authorized
for use as components in systems intended for surgical implant into the body,
or other applications intended to support or sustain life, or for any other
application in which the failure of the Freescale Semiconductor product could
create a situation where personal injury or death may occur. Should Buyer
purchase or use Freescale Semiconductor products for any such unintended
or unauthorized application, Buyer shall indemnify and hold Freescale
Semiconductor and its officers, employees, subsidiaries, affiliates, and
distributors harmless against all claims, costs, damages, and expenses, and
reasonable attorney fees arising out of, directly or indirectly, any claim of
personal injury or death associated with such unintended or unauthorized
use, even if such claim alleges that Freescale Semiconductor was negligent
regarding the design or manufacture of the part.
Freescale™ and the Freescale logo are trademarks of Freescale Semiconductor,
Inc. All other product or service names are the property of their respective owners.
This product incorporates SuperFlash® technology licensed from SST.
© Freescale Semiconductor, Inc. 2005. All rights reserved.
DSP56858
Rev. 6
01/2007