HITACHI HM5216405LTT-10H

HM5216805 Series,
HM5216405 Series
16 M LVTTL Interface SDRAM
100 MHz/83 MHz
1-Mword × 8-bit × 2-bank/2-Mword × 4-bit × 2-bank
ADE-203-304E (Z)
Rev. 5.0
November 1, 1997
Description
All inputs and outputs are referred to the rising edge of the clock input. The HM5216805 Series,
HM5216405 Series are offered in 2 banks for improved performance.
Features
•
•
•
•
•
•
•
•
3.3V Power supply
Clock frequency: 100 MHz/83 MHz (max)
LVTTL interface
Single pulsed RAS
2 Banks can operates simultaneously and independently
Burst read/write operation and burst read/single write operation capability
Programmable burst length: 1/2/4/8/full page
2 variations of burst sequence
 Sequential (BL = 1/2/4/8/full page)
 Interleave (BL = 1/2/4/8)
• Programmable CAS latency: 1/2/3
• Refresh cycles: 4096 refresh cycles/64 ms
• 2 variations of refresh
 Auto refresh
 Self refresh (L-version)
HM5216805 Series, HM5216405 Series
Ordering Information
Type No.
Frequency
Package
HM5216805TT-10H
HM5216805TT-12
100 MHz
83 MHz
400-mil 44-pin plastic TSOP II (TTP-44DE)
HM5216805LTT-10H
100 MHz
HM5216405TT-10H
HM5216405TT-12
100 MHz
83 MHz
HM5216405LTT-10H
100 MHz
2
HM5216805 Series, HM5216405 Series
Pin Arrangement (HM5216805 Series)
HM5216805TT/LTT Series
VCC
1
44
VSS
I/O0
2
43
I/O7
VSSQ
3
42
VSSQ
I/O1
4
41
I/O6
VCCQ
5
40
VCCQ
I/O2
6
39
I/O5
VSSQ
7
38
VSSQ
I/O3
8
37
I/O4
VCCQ
9
36
VCCQ
NC
10
35
NC
NC
11
34
NC
WE
12
33
DQM
CAS
13
32
CLK
RAS
14
31
CKE
CS
15
30
NC
A11
16
29
A9
A10
17
28
A8
A0
18
27
A7
A1
19
26
A6
A2
20
25
A5
A3
21
24
A4
VCC
22
23
VSS
(Top view)
3
HM5216805 Series, HM5216405 Series
Pin Description (HM5216805 Series)
Pin name
Function
A0 to A11
Address input
Row address
A0 to A10
Column address A0 to A8
Bank select address
A11
I/O0 to I/O7
Data-input/output
CS
Chip select
RAS
Row address strobe command
CAS
Column address strobe command
WE
Write enable command
DQM
Input/output mask
CLK
Clock input
CKE
Clock enable
VCC
Power for internal circuit
VSS
Ground for internal circuit
VCCQ
Power for I/O pin
VSS Q
Ground for I/O pin
NC
No connection
4
HM5216805 Series, HM5216405 Series
Pin Arrangement (HM5216405 Series)
HM5216405TT/LTT Series
VCC
1
44
VSS
NC
2
43
NC
VSSQ
3
42
VSSQ
I/O0
4
41
I/O3
VCCQ
5
40
VCCQ
NC
6
39
NC
VSSQ
7
38
VSSQ
I/O1
8
37
I/O2
VCCQ
9
36
VCCQ
NC
10
35
NC
NC
11
34
NC
WE
12
33
DQM
CAS
13
32
CLK
RAS
14
31
CKE
CS
15
30
NC
A11
16
29
A9
A10
17
28
A8
A0
18
27
A7
A1
19
26
A6
A2
20
25
A5
A3
21
24
A4
VCC
22
23
VSS
(Top view)
5
HM5216805 Series, HM5216405 Series
Pin Description (HM5216405 Series)
Pin name
Function
A0 to A11
Address input
Row address
A0 to A10
Column address A0 to A9
Bank select address
A11
I/O0 to I/O3
Data-input/output
CS
Chip select
RAS
Row address strobe command
CAS
Column address strobe command
WE
Write enable command
DQM
Input/output mask
CLK
Clock input
CKE
Clock enable
VCC
Power for internal circuit
VSS
Ground for internal circuit
VCCQ
Power for I/O pin
VSS Q
Ground for I/O pin
NC
No connection
6
HM5216805 Series, HM5216405 Series
Block Diagram (HM5216805 Series)
A0 – A11
A0 – A8
Column address
counter
A0 – A11
Column address
buffer
Memory array
2048 row X 512 column X 8 bit
Memory array
Bank 1
2048 row X 512 column X 8 bit
Output
buffer
Control logic &
timing generator
DQM
WE
CAS
RAS
CS
CKE
I/O0 – I/O7
CLK
Input
buffer
Sense amplifier & I/O bus
Row decoder
Column decoder
Sense amplifier & I/O bus
Column decoder
Row decoder
Bank 0
Refresh
counter
Row address
buffer
7
HM5216805 Series, HM5216405 Series
Block Diagram (HM5216405 Series)
A0 – A11
A0 – A9
Column address
counter
A0 – A11
Column address
buffer
Memory array
2048 row X 1024 column X 4 bit
Input
buffer
Sense amplifier & I/O bus
Row decoder
Column decoder
Sense amplifier & I/O bus
Column decoder
Row decoder
Bank 0
Refresh
counter
Row address
buffer
Memory array
Bank 1
2048 row X 1024 column X 4 bit
Output
buffer
Control logic &
timing generator
8
DQM
WE
CAS
RAS
CS
CKE
CLK
I/O0 – I/O3
HM5216805 Series, HM5216405 Series
Pin Functions
CLK (input pin): CLK is the master clock input to this pin. The other input signals are referred at CLK
rising edge.
CS (input pin): When CS is Low, the command input cycle becomes valid. When CS is High, all inputs
are ignored. However, internal operations (bank active, burst operations, etc.) are held.
RAS, CAS, and WE (input pins): Although these pin names are the same as those of conventional
DRAMs, they function in a different way. These pins define operation commands (read, write, etc.)
depending on the combination of their voltage levels. For details, refer to the command operation section.
A0 to A10 (input pins): Row address (AX0 to AX10) is determined by A0 to A10 level at the bank active
command cycle CLK rising edge. Column address (AY0 to AY8; HM5216805 Series, AY0 to AY9;
HM5216405 Series) is determined by A0 to A8 or A9 (A8; HM5216805 Series, A9; HM5216405 Series)
level at the read or write command cycle CLK rising edge. And this column address becomes burst access
start address. A10 defines the precharge mode. When A10 = High at the precharge command cycle, both
banks are precharged. But when A10 = Low at the precharge command cycle, only the bank that is
selected by A11(BS) is precharged.
A11 (input pin): A11 is a bank select signal (BS). The memory array of the HM5216805 Series, the
HM5216405 Series is divided into bank 0 and bank 1. HM5216805 Series contain 2048 row × 512 column
× 8 bits. HM5216405 Series contain 2048 row × 1024 column × 4 bits. If A11 is Low, bank 0 is selected,
and if A11 is High, bank 1 is selected.
CKE (input pin): This pin determines whether or not the next CLK is valid. If CKE is High, the next
CLK rising edge is valid. If CKE is Low, the next CLK rising edge is invalid. This pin is used for powerdown and clock suspend modes.
DQM (input pins): DQM controls input/output buffers.
Read operation: If DQM is High, the output buffer becomes High-Z. If the DQM is Low, the output buffer
becomes Low-Z.
Write operation: If DQM is High, the previous data is held (the new data is not written). If DQM is Low,
the data is written.
I/O0 to I/O7 (I/O pins): Data is input to and output from these pins. These pins are the same as those of a
conventional DRAM.
VCC and VCCQ (power supply pins): 3.3 V is applied. (VCC is for the internal circuit and V CCQ is for the
output buffer.)
VSS and VSSQ (power supply pins): Ground is connected. (VSS is for the internal circuit and VSS Q is for
the output buffer.)
9
HM5216805 Series, HM5216405 Series
Command Operation
Command Truth Table
The synchronous DRAM recognizes the following commands specified by the CS, RAS, CAS, WE and
address pins.
CKE
Function
Symbol
n–1 n
CS
RAS
CAS
WE
A11
A10
A0 to A9
Ignore command
DESL
H
×
H
×
×
×
×
×
×
No operation
NOP
H
×
L
H
H
H
×
×
×
Burst stop in full page
BST
H
×
L
H
H
L
×
×
×
Column address and read
command
READ
H
×
L
H
L
H
V
L
V
Read with auto-precharge
READ A
H
×
L
H
L
H
V
H
V
Column address and write
command
WRIT
H
×
L
H
L
L
V
L
V
Write with auto-precharge
WRIT A
H
×
L
H
L
L
V
H
V
Row address strobe and
bank act.
ACTV
H
×
L
L
H
H
V
V
V
Precharge select bank
PRE
H
×
L
L
H
L
V
L
×
Precharge all bank
PALL
H
×
L
L
H
L
×
H
×
Refresh
REF/SELF H
V
L
L
L
H
×
×
×
Mode register set
MRS
×
L
L
L
L
V
V
V
H
Note: H: V IH. L: V IL. ×: VIH or VIL. V: Valid address input
Ignore command [DESL]: When this command is set (CS is High), the synchronous DRAM ignore
command input at the clock. However, the internal status is held.
No operation [NOP]: This command is not an execution command. However, the internal operations
continue.
Burst stop in full-page [BST]: This command stops a full-page burst operation (burst length = full-page
(512; HM5216805 Series, 1024; HM5216405 Series)), and is illegal otherwise. Full page burst continues
until this command is input. When data input/output is completed for a full-page of data, it automatically
returns to the start address, and input/output is performed repeatedly.
Column address strobe and read command [READ]: This command starts a read operation. In
addition, the start address of burst read is determined by the column address (AY0 to AY8; HM5216805
Series, AY0 to AY9; HM5216405 Series) and the bank select address (BS). After the read operation, the
output buffer becomes High-Z.
10
HM5216805 Series, HM5216405 Series
Read with auto-precharge [READ A]: This command automatically performs a precharge operation
after a burst read with a burst length of 1, 2, 4, or 8. When the burst length is full-page, this command is
illegal.
Column address strobe and write command [WRIT]: This command starts a write operation. When the
burst write mode is selected, the column address (AY0 to AY8; HM5216805 Series, AY0 to AY9;
HM5216405 Series) and the bank select address (A11) become the burst write start address. When the
single write mode is selected, data is only written to the location specified by the column address (AY0 to
AY8; HM5216805 Series, AY0 to AY9; HM5216405 Series) and the bank select address (A11).
Write with auto-precharge [WRIT A]: This command automatically performs a precharge operation
after a burst write with a length of 1, 2, 4, or 8, or after a single write operation. When the burst length is
full-page, this command is illegal.
Row address strobe and bank activate [ACTV]: This command activates the bank that is selected by
A11 (BS) and determines the row address (AX0 to AX10). When A11 is Low, bank 0 is activated. When
A11 is High, bank 1 is activated.
Precharge selected bank [PRE]: This command starts precharge operation for the bank selected by A11.
If A11 is Low, bank 0 is selected. If A11 is High, bank 1 is selected.
Precharge all banks [PALL]: This command starts a precharge operation for all banks.
Refresh [REF/SELF]: This command starts the refresh operation. There are two types of refresh
operation, the one is auto-refresh, and the other is self-refresh. For details, refer to the CKE truth table
section.
Mode register set [MRS]: Synchronous DRAM has a mode register that defines how it operates. The
mode register is specified by the address pins (A0 to A11) at the mode register set cycle. For details, refer
to the mode register configuration. After power on, the contents of the mode register are undefined,
execute the mode register set command to set up the mode register.
DQM Truth Table
CKE
Function
Symbol
n–1
n
DQM
Write enable/output enable
ENB
H
×
L
Write inhibit/output disable
MASK
H
×
H
Note: H: VIH. L: V IL. ×: VIH or VIL.
The HM5216805 Series, HM5216405 Series can mask input/output data by means of DQM. During
reading, the output buffer is set to Low-Z by setting DQM to Low, enabling data output. On the other
hand, when DQM is set to High, the output buffer becomes High-Z, disabling data output.
During writing, data is written by setting DQM to Low. When DQM is set to High, the previous data is
held (the new data is not written). Desired data can be masked during burst read or burst write by setting
DQM. For details, refer to the DQM control section of the HM5216805 Series, HM5216405 Series
operating instructions.
11
HM5216805 Series, HM5216405 Series
CKE Truth Table
CKE
Current state
Function
n–1 n
CS
RAS
CAS
WE
Address
Active
Clock suspend mode entry
H
L
H
×
×
×
×
Any
Clock suspend
L
L
×
×
×
×
×
Clock suspend Clock suspend mode exit
L
H
×
×
×
×
×
Idle
Auto-refresh command REF
H
H
L
L
L
H
×
Idle
Self-refresh entry
H
L
L
L
L
H
×
Idle
Power down entry
H
L
L
H
H
H
×
H
L
H
×
×
×
×
L
H
L
H
H
H
×
L
H
H
×
×
×
×
L
H
L
H
H
H
×
L
H
H
×
×
×
×
Self refresh
Power down
Self refresh exit
Power down exit
SELF
SELFX
Note: H: VIH. L: V IL. ×: VIH or VIL.
Clock suspend mode entry: The synchronous DRAM enters clock suspend mode from active mode by
setting CKE to Low. The clock suspend mode changes depending on the current status (1 clock before) as
shown below.
ACTIVE clock suspend: This suspend mode ignores inputs after the next clock by internally maintaining
the bank active status.
READ suspend and READ A suspend: The data being output is held (and continues to be output).
WRITE suspend and WRIT A suspend: In this mode, external signals are not accepted. However, the
internal state is held.
Clock suspend: During clock suspend mode, keep the CKE to Low.
Clock suspend mode exit: The synchronous DRAM exits from clock suspend mode by setting CKE to
High during the clock suspend state.
IDLE: In this state, all banks are not selected, and completed precharge operation.
Auto-refresh command [REF]: When this command is input from the IDLE state, the synchronous
DRAM starts auto-refresh operation. (The auto-refresh is the same as the CBR refresh of conventional
DRAMs.) During the auto-refresh operation, refresh address and bank select address are generated inside
the synchronous DRAM. For every auto-refresh cycle, the internal address counter is updated.
Accordingly, 4096 times are required to refresh the entire memory. Before executing the auto-refresh
command, all the banks must be in the IDLE state. In addition, since the precharge for all banks is
automatically performed after auto-refresh, no precharge command is required after auto-refresh.
12
HM5216805 Series, HM5216405 Series
Self-refresh entry [SELF]: When this command is input during the IDLE state, the synchronous DRAM
starts self-refresh operation. After the execution of this command, self-refresh continues while CKE is
Low. Since self-refresh is performed internally and automatically, external refresh operations are
unnecessary.
Power down mode entry: When this command is executed during the IDLE state, the synchronous
DRAM enters power down mode. In power down mode, power consumption is suppressed by cutting off
the initial input circuit.
Self-refresh exit: When this command is executed during self-refresh mode, the synchronous DRAM can
exit from self-refresh mode. After exiting from self-refresh mode, the synchronous DRAM enters the
IDLE state.
Power down exit: When this command is executed at the power down mode, the synchronous DRAM can
exit from power down mode. After exiting from power down mode, the synchronous DRAM enters the
IDLE state.
13
HM5216805 Series, HM5216405 Series
Function Truth Table
The following table shows the operations that are performed when each command is issued in each mode of
the synchronous DRAM.
Current state
CS
RAS CAS WE
Address
Command
Operation
Precharge
H
×
×
×
×
DESL
Enter IDLE after t RP
L
H
H
H
×
NOP
Enter IDLE after t RP
L
H
H
L
×
BST
NOP
L
H
L
H
BA, CA, A10
READ/READ A
ILLEGAL
L
H
L
L
BA, CA, A10
WRIT/WRIT A
ILLEGAL
L
L
H
H
BA, RA
ACTV
ILLEGAL
L
L
H
L
BA, A10
PRE, PALL
NOP
L
L
L
H
×
REF, SELF
ILLEGAL
L
L
L
L
MODE
MRS
ILLEGAL
H
×
×
×
×
DESL
NOP
L
H
H
H
×
NOP
NOP
L
H
H
L
×
BST
NOP
L
H
L
H
BA, CA, A10
READ/READ A
ILLEGAL
L
H
L
L
BA, CA, A10
WRIT/WRIT A
ILLEGAL
L
L
H
H
BA, RA
ACTV
Bank and row active
L
L
H
L
BA, A10
PRE, PALL
NOP
L
L
L
H
×
REF, SELF
Refresh
L
L
L
L
MODE
MRS
Mode register set
H
×
×
×
×
DESL
NOP
L
H
H
H
×
NOP
NOP
L
H
H
L
×
BST
NOP
L
H
L
H
BA, CA, A10
READ/READ A
Begin read
L
H
L
L
BA, CA, A10
WRIT/WRIT A
Begin write
L
L
H
H
BA, RA
ACTV
Other bank active
ILLEGAL on same bank*3
L
L
H
L
BA, A10
PRE, PALL
Precharge
L
L
L
H
×
REF, SELF
ILLEGAL
L
L
L
L
MODE
MRS
ILLEGAL
Idle
Row active
14
HM5216805 Series, HM5216405 Series
Current state
CS
RAS CAS WE
Address
Command
Operation
Read
H
×
×
×
×
DESL
Continue burst to end
L
H
H
H
×
NOP
Continue burst to end
L
H
H
L
×
BST
Burst stop on full page
L
H
L
H
BA, CA, A10
READ/READ A
Continue burst read to CAS
latency and New read
L
H
L
L
BA, CA, A10
WRIT/WRIT A
Term burst read/start write
L
L
H
H
BA, RA
ACTV
Other bank active
ILLEGAL on same bank*3
L
L
H
L
BA, A10
PRE, PALL
Term burst read and Precharge
L
L
L
H
×
REF, SELF
ILLEGAL
L
L
L
L
MODE
MRS
ILLEGAL
Read with auto- H
precharge
×
×
×
×
DESL
Continue burst to end and
precharge
L
H
H
H
×
NOP
Continue burst to end and
precharge
L
H
H
L
×
BST
ILLEGAL
L
H
L
H
BA, CA, A10
READ/READ A
ILLEGAL
L
H
L
L
BA, CA, A10
WRIT/WRIT A
ILLEGAL
L
L
H
H
BA, RA
ACTV
Other bank active
ILLEGAL on same bank *3
L
L
H
L
BA, A10
PRE, PALL
ILLEGAL
L
L
L
H
×
REF, SELF
ILLEGAL
L
L
L
L
MODE
MRS
ILLEGAL
H
×
×
×
×
DESL
Continue burst to end
L
H
H
H
×
NOP
Continue burst to end
L
H
H
L
×
BST
Burst stop on full page
L
H
L
H
BA, CA, A10
READ/READ A
Term burst and New read
L
H
L
L
BA, CA, A10
WRIT/WRIT A
Term burst and New write
L
L
H
H
BA, RA
ACTV
Other bank active
ILLEGAL on same bank*3
L
L
H
L
BA, A10
PRE, PALL
Term burst write and
Precharge*2
L
L
L
H
×
REF, SELF
ILLEGAL
L
L
L
L
MODE
MRS
ILLEGAL
Write
15
HM5216805 Series, HM5216405 Series
RAS CAS WE
Address
Command
Operation
Write with auto- H
precharge
×
×
×
×
DESL
Continue burst to end and
precharge
L
H
H
H
×
NOP
Continue burst to end and
precharge
L
H
H
L
×
BST
ILLEGAL
L
H
L
H
BA, CA, A10
READ/READ A
ILLEGAL
L
H
L
L
BA, CA, A10
WRIT/WRIT A
ILLEGAL
L
L
H
H
BA, RA
ACTV
Other bank active
ILLEGAL on same bank *3
L
L
H
L
BA, A10
PRE, PALL
ILLEGAL
L
L
L
H
×
REF, SELF
ILLEGAL
L
L
L
L
MODE
MRS
ILLEGAL
H
×
×
×
×
DESL
Enter IDLE after t RC
L
H
H
H
×
NOP
Enter IDLE after t RC
L
H
H
L
×
BST
Enter IDLE after t RC
L
H
L
H
BA, CA, A10
READ/READ A
ILLEGAL
L
H
L
L
BA, CA, A10
WRIT/WRIT A
ILLEGAL
L
L
H
H
BA, RA
ACTV
ILLEGAL
L
L
H
L
BA, A10
PRE, PALL
ILLEGAL
L
L
L
H
×
REF, SELF
ILLEGAL
L
L
L
L
MODE
MRS
ILLEGAL
Current state
Refresh (autorefresh)
CS
Notes: 1. H: VIH. L: V IL. ×: VIH or VIL.
The other combinations are inhibit.
2. An interval of t DPL is required between the final valid data input and the precharge command.
3. If tRRD is not satisfied, this operation is illegal.
From [PRECHARGE]
To [DESL], [NOP] or [BST]: When these commands are executed, the synchronous DRAM enters the
IDLE state after tRP has elapsed from the completion of precharge.
From [IDLE]
To [DESL], [NOP], [BST], [PRE] or [PALL]: These commands result in no operation.
To [ACTV]: The bank specified by the address pins and the ROW address is activated.
To [REF], [SELF]: The synchronous DRAM enters refresh mode (auto-refresh or self-refresh).
To [MRS]: The synchronous DRAM enters the mode register set cycle.
16
HM5216805 Series, HM5216405 Series
From [ROW ACTIVE]
To [DESL], [NOP] or [BST]: These commands result in no operation.
To [READ], [READ A]: A read operation starts. (However, an interval of tRCD is required.)
To [WRIT], [WRIT A]: A write operation starts. (However, an interval of tRCD is required.)
To [ACTV]: This command makes the other bank active. (However, an interval of tRRD is required.)
Attempting to make the currently active bank active results in an illegal command.
To [PRE], [PALL]: These commands set the synchronous DRAM to precharge mode. (However, an
interval of t RAS is required.)
From [READ]
To [DESL], [NOP]: These commands continue read operations until the burst operation is completed.
To [BST]: This command stops a full-page burst.
To [READ], [READ A]: Data output by the previous read command continues to be output. After CAS
latency, the data output resulting from the next command will start.
To [WRIT], [WRIT A]: These commands stop a burst read, and start a write cycle.
To [ACTV]: This command makes other banks bank active. (However, an interval of tRRD is required.)
Attempting to make the currently active bank active results in an illegal command.
To [PRE], [PALL]: These commands stop a burst read, and the synchronous DRAM enters precharge
mode.
From [READ with AUTO-PRECHARGE]
To [DESL], [NOP]: These commands continue read operations until the burst operation is completed, and
the synchronous DRAM then enters precharge mode.
To [ACTV]: This command makes other banks bank active. (However, an interval of tRRD is required.)
Attempting to make the currently active bank active results in an illegal command.
17
HM5216805 Series, HM5216405 Series
From [WRITE]
To [DESL], [NOP]: These commands continue write operations until the burst operation is completed.
To [BST]: This command stops a full-page burst.
To [READ], [READ A]: These commands stop a burst and start a read cycle.
To [WRIT], [WRIT A]: These commands stop a burst and start the next write cycle.
To [ACTV]: This command makes the other bank active. (However, an interval of tRRD is required.)
Attempting to make the currently active bank active results in an illegal command.
To [PRE], [PALL]: These commands stop burst write and the synchronous DRAM then enters precharge
mode.
From [WRITE with AUTO-PRECHARGE]
To [DESL], [NOP]: These commands continue write operations until the burst is completed, and the
synchronous DRAM enters precharge mode.
To [ACTV]: This command makes the other bank active. (However, an interval of t RC is required.)
Attempting to make the currently active bank active results in an illegal command.
From [REFRESH]
To [DESL], [NOP]: After an auto-refresh cycle (after tRC), the synchronous DRAM automatically enters
the IDLE state.
18
HM5216805 Series, HM5216405 Series
Simplified State Diagram
SELF
REFRESH
SR ENTRY
SR EXIT
MRS
MODE
REGISTER
SET
REFRESH
IDLE
*1
AUTO
REFRESH
CKE
CKE_
IDLE
POWER
DOWN
ACTIVE
ACTIVE
CLOCK
SUSPEND
CKE_
CKE
ROW
ACTIVE
BST
(on full page)
BST
(on full page)
WRITE
Write
WRITE
SUSPEND
CKE_
WRITE
READ
WRITE
WITH
AP
READ
WRITE
CKE
READ
WITH AP
WRITE
WITH AP
WRITEA
READ
CKE
CKE
POWER
ON
READ
SUSPEND
READ
WITH AP
CKE_
READA
CKE
PRECHARGE
POWER
APPLIED
WRITE
WITH AP
Read
CKE_
PRECHARGE
CKE_
WRITEA
SUSPEND
READ
WITH
AP
READA
SUSPEND
PRECHARGE
PRECHARGE
PRECHARGE
Automatic transition after completion of command.
Transition resulting from command input.
Note: 1. After the auto-refresh operation, precharge operation is performed automatically and
enter the IDLE state.
19
HM5216805 Series, HM5216405 Series
Mode Register Configuration
The mode register is set by the input to the address pins (A0 to A11) during mode register set cycles. The
mode register consists of five sections, each of which is assigned to address pins.
A11, A10, A9, A8 (OPCODE): The synchronous DRAM has two types of write modes. One is the burst
write mode, and the other is the single write mode. These bits specify write mode.
Burst read and BURST WRITE: Burst write is performed for the specified burst length starting from the
column address specified in the write cycle.
Burst read and SINGLE WRITE: Data is only written to the column address specified during the write
cycle, regardless of the burst length.
A7: Keep this bit Low at the mode register set cycle.
A6, A5, A4 (LMODE): These pins specify the CAS latency.
A3 (BT): A burst type is specified. When full-page burst is performed, only “sequential” can be selected.
A2, A1, A0 (BL): These pins specify the burst length.
A11
A10
A9
A8
A7
OPCODE
0
A6
A11 A10
A9
A8
0
0
0
0
X
X
0
1
X
X
1
0
X
X
1
1
20
A6
A5
A4
LMODE
A5
A3
A2
BT
A4 CAS Latency
0
0
0
R
0
0
1
1
A1
A0
BL
A3 Burst Type
0 Sequential
1
Interleave
A2 A1
A0
Burst Length
BT=0
BT=1
0
0
0
1
1
0
1
0
2
0
0
1
2
2
0
1
1
3
0
1
0
4
4
1
X
X
R
0
1
1
8
8
1
0
0
R
R
1
0
1
R
R
1
1
0
R
R
1
1
1
F.P.
R
Write mode
Burst read and burst write
R
Burst read and SINGLE WRITE
R
F.P. = Full Page (512: HM5216805)
(1024: HM5216405)
R is Reserved (inhibit)
X: 0 or 1
HM5216805 Series, HM5216405 Series
Burst Sequence
Burst length = 2
Burst length = 4
Starting Ad. Addressing(decimal)
A0
Sequence
Interleave
Starting Ad. Addressing(decimal)
A1
A0
Sequence
Interleave
0
0, 1,
0, 1,
0
0, 1, 2, 3,
0
1
1, 0,
1, 0,
0
0, 1, 2, 3,
1
1, 2, 3, 0,
1, 0, 3, 2,
1
0
2, 3, 0, 1,
2, 3, 0, 1,
1
1
3, 0, 1, 2,
3, 2, 1, 0,
Burst length = 8
Addressing(decimal)
Starting Ad.
A2
A1
0
0
A0 Sequence
0
0, 1, 2, 3, 4, 5, 6, 7,
Interleave
0, 1, 2, 3, 4, 5, 6, 7,
0
0
1
1, 2, 3, 4, 5, 6, 7, 0,
1, 0, 3, 2, 5, 4, 7, 6,
0
1
0
2, 3, 4, 5, 6, 7, 0, 1,
2, 3, 0, 1, 6, 7, 4, 5,
0
1
1
3, 4, 5, 6, 7, 0, 1, 2,
3, 2, 1, 0, 7, 6, 5, 4,
1
0
0
4, 5, 6, 7, 0, 1, 2, 3,
4, 5, 6, 7, 0, 1, 2, 3,
1
0
1
5, 6, 7, 0, 1, 2, 3, 4,
5, 4, 7, 6, 1, 0, 3, 2,
1
1
0
6, 7, 0, 1, 2, 3, 4, 5,
6, 7, 4, 5, 2, 3, 0, 1,
1
1
1
7, 0, 1, 2, 3, 4, 5, 6,
7, 6, 5, 4, 3, 2, 1, 0,
21
HM5216805 Series, HM5216405 Series
Operation of HM5216805 Series, HM5216405 Series
Read/Write Operations
Bank active: Before executing a read or write operation, the corresponding bank and the row address must
be activated by the bank active (ACTV) command. Either bank 0 or bank 1 is activated according to the
status of the A11 pin, and the row address (AX0 to AX10) is activated by the A0 to A10 pins at the bank
active command cycle. An interval of tRCD is required between the bank active command input and the
following read/write command input.
Read operation: A read operation starts when a read command is input. Output buffer becomes Low-Z in
the (CAS Latency - 1) cycle after read command set. HM5216805 Series, HM5216405 Series can perform
a burst read operation. The burst length can be set to 1, 2, 4, 8 or full-page (512; HM5216805 Series,
1024; HM5216405 Series). The start address for a burst read is specified by the column address (AY0 to
AY8; HM5216805 Series, AY0 to AY9; HM5216405 Series) and the bank select address (A11) at the read
command set cycle. In a read operation, data output starts after the number of cycles specified by the CAS
Latency. The CAS Latency can be set to 1, 2 or 3. When the burst length is 1, 2, 4, or 8, the Dout buffer
automatically becomes High-Z at the next cycle after the successive burst-length data has been output.
When the burst length is full-page (512; HM5216805 Series, 1024; HM5216405 Series), data is
repeatedly output until the burst stop command is input. The CAS latency and burst length must be
specified at the mode register.
CAS Latency
CLK
t RCD
Command
Address
ACTV
Row
CL = 1
Dout
CL = 2
CL = 3
22
READ
Column
out 0
out 1
out 2
out 3
out 0
out 1
out 2
out 3
out 0
out 1
out 2
out 3
CL: CAS latency
Burst length = 4
HM5216805 Series, HM5216405 Series
Burst Length
CLK
t RCD
Command
ACTV
READ
Address
Row
Column
out 0
BL = 1
out 0 out 1
BL = 2
Dout
out 0 out 1 out 2 out 3
BL = 4
out 0 out 1 out 2 out 3 out 4 out 5 out 6 out 7
BL = 8
out 0 out 1 out 2 out 3 out 4 out 5 out 6 out 7 out 8
out 255
BL = full page
out 0
out 1
BL: Burst Length
CAS Latency = 2
Write operation: Burst write or single write mode is selected by the OPCODE (A11, A10, A9, A8) of the
mode register.
Burst write: A burst write operation is enabled by setting OPCODE (A9, A8) to (0, 0). A burst write
starts in the same cycle as a write command set. (The latency of data input is 0.) The burst length can be
set to 1, 2, 4 or 8 and full-page, like burst read operations. The write start address is specified by the
column address (AY0 to AY8; HM5216805 Series, AY0 to AY9; HM5216405 Series) and the bank select
address (A11) at the write command set cycle.
CLK
t RCD
Command
ACTV
WRIT
Address
Row
Column
BL = 1
in 0
in 0
in 1
in 0
in 1
in 2
in 3
in 0
in 1
in 2
in 3
in 4
in 5
in 6
in 7
in 0
in 1
in 2
in 3
in 4
in 5
in 6
in 7
BL = 2
Din
BL = 4
BL = 8
BL = full page
in 8
in 255
in 0
in 1
CAS Latency = 1, 2, 3
23
HM5216805 Series, HM5216405 Series
Single write: A single write operation is enabled by setting OPCODE (A9, A8) to (1, 0). In a single write
operation, data is only written to the column address (AY0 to AY8; HM5216805 Series, AY0 to AY9;
HM5216405 Series) and the bank select address (A11) specified by the write command set cycle without
regard to the burst length setting. (The latency of data input is 0).
CLK
t RCD
Command
Address
Din
Active
Row
Write
Column
in 0
CAS latency = 1, 2, 3
Burst length = 1, 2, 4, 8, full page
24
HM5216805 Series, HM5216405 Series
Auto-precharge
Read with auto-precharge: In this operation, since precharge is automatically performed after completing
a read operation, a precharge command need not be executed after each read operation. The command
executed for the same bank after the execution of this command must be the bank active (ACTV)
command. In addition, an interval defined by lAPR is required before execution of the next command.
CAS latency
Precharge start cycle
3
2 cycle before the final data is output
2
1 cycle before the final data is output
1
same cycle as the final data is output
CLK
CL = 1 Command
READ
ACTV
out0
Dout
out1
out2
out3
lAPR
CL = 2 Command
READ
ACTV
out0
Dout
out1
out2
out3
lAPR
CL = 3 Command
Dout
READ
ACTV
out0
out1
out2
out3
lAPR
Note: Internal auto-precharge starts at the timing indicated by "
".
At CLK = 50 MHz ( lAPR changes depending on the operating frequency. )
25
HM5216805 Series, HM5216405 Series
Write with auto-precharge: In this operation, since precharge is automatically performed after
completing a burst write or single write operation, a precharge command need not be executed after each
write operation. The command executed for the same bank after the execution of this command must be
the bank active (ACTV) command. In addition, an interval of lAPW is required between the final valid data
input and input of the next command.
Burst Write (Burst Length = 4)
CLK
Command
I/O (input)
WRIT
in0
ACTV
in1
in2
in3
lAPW
Single Write
CLK
Command
I/O (input)
WRIT
ACTV
in
lAPW
26
HM5216805 Series, HM5216405 Series
Full-page Burst Stop
Burst stop command during burst read: The burst stop (BST) command is used to stop data output
during a full-page burst. The BST command sets the output buffer to High-Z and stops the full-page burst
read. The timing from command input to the last data changes depending on the CAS latency setting. In
addition, the BST command is valid only during full-page burst mode, and is invalid with burst lengths 1,
2, 4 and 8.
CAS latency
BST to valid data
BST to high impedance
1
0
1
2
1
2
3
2
3
CAS Latency = 1, Burst Length = full page
CLK
BST
Command
I/O (output)
out
out
out
out
out
l BSR
l BSH
0 cycle
1 cycle
CAS Latency = 2, Burst Length = full page
CLK
BST
Command
I/O (output)
out
out
out
out
out
out
l BSH = 2 cycle
l BSR = 1 cycle
27
HM5216805 Series, HM5216405 Series
CAS Latency = 3, Burst Length = full page
CLK
BST
Command
I/O (output)
out
out
out
out
out
out
l BSR = 2 cycle
out
l BSH = 3 cycle
Burst stop command at burst write: The burst stop command (BST command) is used to stop data input
during a full-page burst write. No data is written in the same cycle as the BST command, and in
subsequent cycles. In addition, the BST command is only valid during full-page burst mode, and is invalid
with burst lengths of 1, 2, 4 and 8. And an interval of tDPL is required between the BST command and the
next precharge command.
Burst Length = full page
CLK
BST
Command
I/O (input)
in
in
t DPL
I BSW = 0 cycle
28
PRE/PALL
HM5216805 Series, HM5216405 Series
Command Intervals
Read command to Read command interval
Same bank, same ROW address: When another read command is executed at the same ROW address of
the same bank as the preceding read command execution, the second read can be performed after an
interval of no less than 1 cycle. Even when the first command is a burst read that is not yet finished, the
data read by the second command will be valid.
READ to READ Command Interval (same ROW address in same bank)
CLK
Command
ACTV
Address
(A0-A10)
Row
READ
READ
Column A Column B
BS (A11)
Dout
out A0 out B0 out B1 out B2 out B3
Bank0
Active
Column =A Column =B Column =A Column =B
Dout
Read
Read
Dout
CAS Latency = 3
Burst Length = 4
Bank0
Same bank, different ROW address: When the ROW address changes on same bank, consecutive read
commands cannot be executed; it is necessary to separate the two read commands with a precharge
command and a bank-active command.
Different bank: When the bank changes, the second read can be performed after an interval of no less
than 1 cycle, provided that the other bank is in the bank-active state. Even when the first command is a
burst read that is not yet finished, the data read by the second command will be valid.
READ to READ Command Interval (different bank)
CLK
Command
ACTV
ACTV
READ READ
Address
(A0-A10)
Row 0
Row 1
Column A Column B
BS (A11)
Dout
out A0 out B0 out B1 out B2 out B3
Bank0
Active
Bank1 Bank0 Bank1
Active Read Read
Bank0 Bank1
Dout
Dout
CAS Latency = 3
Burst Length = 4
29
HM5216805 Series, HM5216405 Series
Write command to Write command interval
Same bank, same ROW address: When another write command is executed at the same ROW address of
the same bank as the preceding write command, the second write can be performed after an interval of no
less than 1 cycle. In the case of burst writes, the second write command has priority.
WRITE to WRITE Command Interval (same ROW address in same bank)
CLK
Command
ACTV
Address
(A0-A10)
Row
WRIT
WRIT
Column A Column B
BS (A11)
Din
in A0
Bank0
Active
in B0
in B1
in B2
in B3
Burst Write Mode
Burst Length = 4
Bank0
Column =A Column =B
Write
Write
Same bank, different ROW address: When the ROW address changes, consecutive write commands
cannot be executed; it is necessary to separate the two write commands with a precharge command and a
bank-active command.
Different bank: When the bank changes, the second write can be performed after an interval of no less
than 1 cycle, provided that the other bank is in the bank-active state. In the case of burst write, the second
write command has priority.
WRITE to WRITE Command Interval (different bank)
CLK
Command
Address
(A0-A10)
ACTV
Row 0
ACTV WRIT
Row 1
WRIT
Column A Column B
BS (A11)
Din
in A0
Bank0
Active
30
in B0
Bank1 Bank0 Bank1
Active Write Write
in B1
in B2
in B3
Burst Write Mode
Burst Length = 4
HM5216805 Series, HM5216405 Series
Read command to Write command interval
Same bank, same ROW address: When the write command is executed at the same ROW address of the
same bank as the preceding read command, the write command can be performed after an interval of no
less than 1 cycle. However, DQM must be set High so that the output buffer becomes High-Z before data
input.
READ to WRITE Command Interval-1
CLK
Command
READ WRIT
CL=1
DQM
CL=2
CL=3
in B0
Din
in B1
in B2
in B3
Burst Length = 4
Burst write
High-Z
Dout
READ to WRITE Command Interval-2
CLK
Command
DQM
CL=1
Dout CL=2
CL=3
READ
WRIT
2 clock
High-Z
High-Z
High-Z
Din
Same bank, different ROW address: When the ROW address changes, consecutive write commands
cannot be executed; it is necessary to separate the two commands with a precharge command and a bankactive command.
Different bank: When the bank changes, the write command can be performed after an interval of no less
than 1 cycle, provided that the other bank is in the bank-active state. However, DQM must be set High so
that the output buffer becomes High-Z before data input.
31
HM5216805 Series, HM5216405 Series
Write command to Read command interval
Same bank, same ROW address: When the read command is executed at the same ROW address of the
same bank as the preceding write command, the read command can be performed after an interval of no
less than 1 cycle. However, in the case of a burst write, data will continue to be written until one cycle
before the read command is executed.
WRITE to READ Command Interval-1
CLK
Command
WRIT
READ
DQM
Din
in A0
Dout
out B0
Column=A
Write
out B1
out B2
out B3
CAS Latency
Column=B
Read
Burst Write Mode
CAS Latency = 1
Burst Length = 4
Bank = 0
Column=B
Dout
WRITE to READ Command Interval-2
CLK
Command
WRIT
READ
DQM
Din
in A0
in A1
Dout
out B0
Column=A
Write
CAS Latency
Column=B
Read
Column=B
Dout
out B1
out B2
out B3
Burst Write Mode
CAS Latency = 1
Burst Length = 4
Bank = 0
Same bank, different ROW address: When the ROW address changes, consecutive read commands
cannot be executed; it is necessary to separate the two commands with a precharge command and a bankactive command.
Different bank: When the bank changes, the read command can be performed after an interval of no less
than 1 cycle, provided that the other bank is in the bank-active state. However, in the case of a burst write,
data will continue to be written until one cycle before the read command is executed (as in the case of the
same bank and the same address).
32
HM5216805 Series, HM5216405 Series
Read command to Precharge command interval (same bank): When the precharge command is
executed for the same bank as the read command that preceded it, the minimum interval between the two
commands is one cycle. However, since the output buffer then becomes High-Z after the cycles defined by
lHZP, there is a possibility that burst read data output will be interrupted, if the precharge command is input
during burst read. To read all data by burst read, the cycles defined by lEP must be assured as an interval
from the final data output to precharge command execution.
READ to PRECHARGE Command Interval (same bank): To output all data
CAS Latency = 1, Burst Length = 4
CLK
Command
READ
PRE/PALL
Dout
out A0
out A1
out A2
out A3
l EP = 0 cycle
CL=1
CAS Latency = 2, Burst Length = 4
CLK
Command
READ
PRE/PALL
Dout
out A0
out A1
CL=2
out A2
out A3
l EP = -1 cycle
CAS Latency = 3, Burst Length = 4
CLK
Command
READ
PRE/PALL
Dout
out A0
CL=3
out A1
out A2
out A3
l EP = -2 cycle
33
HM5216805 Series, HM5216405 Series
READ to PRECHARGE Command Interval (same bank): To stop output data
CAS Latency = 1, Burst Length = 1, 2, 4, 8
CLK
Command
READ
PRE/PALL
High-Z
Dout
out A0
l HZP =1
CAS Latency = 2, Burst Length = 1, 2, 4, 8
CLK
Command
READ
PRE/PALL
High-Z
Dout
out A0
l HZP =2
CAS Latency = 3, Burst Length = 1, 2, 4, 8
CLK
Command
READ
PRE/PALL
High-Z
Dout
out A0
l HZP =3
34
HM5216805 Series, HM5216405 Series
Write command to Precharge command interval (same bank): When the precharge command is
executed for the same bank as the write command that preceded it, the minimum interval between the two
commands is 1 cycle. However, if the burst write operation is unfinished, the input data must be masked
by means of DQM for assurance of the cycle defined by tDPL.
WRITE to PRECHARGE Command Interval (same bank)
Burst Length = 4 (To stop write operation)
CLK
Command
WRIT
PRE/PALL
DQM
Din
t DPL
CLK
Command
PRE/PALL
WRIT
DQM
Din
in A0
in A1
t DPL
Burst Length = 4 (To write all data)
CLK
Command
PRE/PALL
WRIT
DQM
Din
in A0
in A1
in A2
in A3
t DPL
35
HM5216805 Series, HM5216405 Series
Bank active command interval
Same bank: The interval between the two bank-active commands must be no less than tRC.
In the case of different bank-active commands: The interval between the two bank-active commands
must be no less than tRRD.
Bank active to bank active for same bank
CLK
Command
ACTV
ACTV
Address
(A0-A10)
ROW
ROW
BS (A11)
t RC
Bank 0
Active
Bank 0
Active
Bank active to bank active for different bank
CLK
Command
ACTV
ACTV
Address
(A0-A10)
ROW:0
ROW:1
BS (A11)
t RRD
Bank 0
Active
36
Bank 1
Active
HM5216805 Series, HM5216405 Series
Mode register set to Bank-active command interval: The interval between setting the mode register and
executing a bank-active command must be no less than tRSA .
CLK
Command
MRS
ACTV
Address
(A0-A11)
CODE
BS & ROW
t RSA
Mode
Register Set
Bank
Active
37
HM5216805 Series, HM5216405 Series
DQM Control
The DQM mask the lower and upper bytes of the I/O data, respectively. The timing of DQM is different
during reading and writing.
Reading: When data is read, the output buffer can be controlled by DQM.
By setting DQM to Low, the output buffer becomes Low-Z, enabling data output. By setting DQM to
High, the output buffer becomes High-Z, and the corresponding data is not output. However, internal
reading operations continue. The latency of DQM during reading is 2.
CLK
DQM
I/O(output)
High-Z
out 0
out 1
out 3
lDOD = 2 Latency
Writing: Input data can be masked by DQM. By setting DQM to Low, data can be written. In addition,
when DQM is set to High, the corresponding data is not written, and the previous data is held. The latency
of DQM during writing is 0.
CLK
DQM
I/O(input)
in 0
in 3
in 1
l DID = 0 Latency
38
HM5216805 Series, HM5216405 Series
Refresh
Auto-refresh: All the banks must be precharged before executing an auto-refresh command. Since the
auto-refresh command updates the internal counter every time it is executed and determines the banks and
the ROW addresses to be refreshed, external address specification is not required. The refresh cycle is
4,096 cycles/64 ms. (4,096 cycles are required to refresh all the ROW addresses.) The output buffer
becomes High-Z after auto-refresh start. In addition, since a precharge has been completed by an internal
operation after the auto-refresh, an additional precharge operation by the precharge command is not
required.
Self-refresh: After executing a self-refresh command, the self-refresh operation continues while CKE is
held Low. During self-refresh operation, all ROW addresses are refreshed by the internal refresh timer. A
self-refresh is terminated by a self-refresh exit command. If you use distributed auto-refresh mode with
15.6 µs interval in normal read/write cycle, auto-refresh should be executed within 15.6 µs immediately
after exiting from and before entering into self refresh mode. If you use address refresh or burst autorefresh mode in normal read/write cycle, 4096 cycles of distributed auto-refresh with 15.6 µs interval
should be executed within 64 ms immediately after exiting from and before entering into self refresh mode.
Others
Power-down mode: The synchronous DRAM enters power-down mode when CKE goes Low in the IDLE
state. In power down mode, power consumption is suppressed by deactivating the input initial circuit.
Power down mode continues while CKE is held Low. In addition, by setting CKE to High, the
synchronous DRAM exits from the power down mode, and command input is enabled from the next cycle.
In this mode, internal refresh is not performed.
Clock suspend mode: By driving CKE to Low during a bank-active or read/write operation, the
synchronous DRAM enters clock suspend mode. During clock suspend mode, external input signals are
ignored and the internal state is maintained. When CKE is driven High, the synchronous DRAM
terminates clock suspend mode, and command input is enabled from the next cycle. For details, refer to the
"CKE Truth Table".
Power-up sequence: During power-up sequence, the DQM and the CKE must be set to High. When 200
µs has past after power on, all banks must be precharged using the precharge command. After tRP delay, set
8 or more auto refresh commands. And set the mode register set command to initialize the mode register.
39
HM5216805 Series, HM5216405 Series
Absolute Maximum Ratings
Parameter
Symbol
Value
Unit
Note
Voltage on any pin relative to V SS
VT
–1.0 to +4.6
V
1
Supply voltage relative to VSS
VCC
–1.0 to +4.6
V
1
Short circuit output current
Iout
50
mA
Power dissipation
PT
1.0
W
Operating temperature
Topr
0 to +70
°C
Storage temperature
Tstg
–55 to +125
°C
Note:
1. Respect to V SS
Recommended DC Operating Conditions (Ta = 0 to +70°C)
Parameter
Symbol
Min
Max
Unit
Notes
Supply voltage
VCC, VCCQ
3.0
3.6
V
1
VSS , VSS Q
0
0
V
Input high voltage
VIH
2.0
4.6
V
1, 2
Input low voltage
VIL
–0.3
0.8
V
1, 3
Notes: 1. All voltage referred to VSS
2. VIH (max) = 5.5 V for pulse width ≤ 5 ns
3. VIL (min) = –1.0 V for pulse width ≤ 5 ns
40
HM5216805 Series, HM5216405 Series
DC Characteristics (Ta = 0 to 70°C, VCC, VCCQ = 3.3 V ± 0.3 V, VSS, VSSQ = 0 V)
HM5216805/HM5216405
-10H
-12
Parameter
Symbol
Min
Max
Min
Max
Unit Test conditions
Notes
Operating current
I CC1
—
100
—
85
mA
t RC = min
Burst length = 1
1, 2, 4
Standby current
(Bank Disable)
I CC2
—
3
—
3
mA
CKE = VIL,
t CK = min
5
—
2
—
2
mA
CKE = VIL
CLK = VIL
or V IH Fixed
6
—
40
—
35
mA
CKE = VIH,
NOP command
t CK = min
3
—
7
—
7
mA
CKE = VIL,
t CK = min,
I/O = High-Z
1, 2
—
45
—
40
mA
CKE = VIH,
NOP command
t CK = min,
I/O = High-Z
1, 2, 3
I CC4
—
65
—
55
mA
t CK = min
BL = 4
1, 2, 4
(CAS latency = 2)
I CC4
—
100
—
85
mA
(CAS latency = 3)
I CC4
—
150
—
125
mA
Refresh current
I CC5
—
85
—
70
mA
t RC = min
Self refresh current
I CC6
—
2
—
2
mA
VIH ≥ V CC – 0.2
VIL ≤ 0.2 V
7
Self refresh current
(L-version)
I CC6
—
250
—
—
µA
VIH ≥ V CC – 0.2
VIL ≤ 0.2 V
7
Input leakage current
I LI
–10
10
–10
10
µA
0 ≤ Vin ≤ V CC
Output leakage current
I LO
–10
10
–10
10
µA
0 ≤ Vout ≤ V CC
I/O = disable
Output high voltage
VOH
2.4
—
2.4
—
V
I OH = –2 mA
Output low voltage
VOL
—
0.4
—
0.4
V
I OL = 2 mA
Active standby current
(Bank active)
Burst operating current
(CAS latency = 1)
I CC3
41
HM5216805 Series, HM5216405 Series
Notes: 1. I CC depends on output load condition when the device is selected. ICC (max) is specified at the
output open condition.
2. One bank operation.
3. Input signal transition is once per two CLK cycles.
4. Input signal transition is once per one CLK cycle.
5. After power down mode set, CLK operating current.
6. After power down mode set, no CLK operating current.
7. After self refresh mode set, self refresh current.
Capacitance (Ta = 25°C, VCC, VCCQ = 3.3 V ± 0.3 V)
Parameter
Symbol
Min
Max
Unit
Notes
Input capacitance (Address)
CI1
2
5
pF
1, 3
Input capacitance (Signals)
CI2
2
5
pF
1, 3
Output capacitance (I/O)
CO
4
7
pF
1, 2, 3
Notes: 1. Capacitance measured with Boonton Meter or effective capacitance measuring method.
2. DQM = VIH to disable Dout.
3. This parameter is sampled and not 100% tested.
42
HM5216805 Series, HM5216405 Series
AC Characteristics (Ta = 0 to 70°C, VCC, VCCQ = 3.3 V ± 0.3 V, VSS, VSSQ = 0 V)
HM5216805/HM5216405
-10H
-12
Parameter
Symbol
Min
Max
Min
Max
Unit
Notes
System clock cycle time
(CAS latency = 1)
t CK
30
—
36
—
ns
1
(CAS latency = 2)
t CK
15
—
18
—
(CAS latency = 3)
t CK
10
—
12
—
CLK high pulse width
t CKH
3
—
4
—
ns
1
CLK low pulse width
t CKL
3
—
4
—
ns
1
Access time from CLK
(CAS latency = 1)
t AC
—
27
—
32
ns
1, 2
(CAS latency = 2)
t AC
—
9.0
—
12
(CAS latency = 3)
t AC
—
7.5
—
9
Data-out hold time
t OH
3
—
3
—
ns
1, 2
CLK to Data-out low impedance
t LZ
0
—
0
—
ns
1, 2, 3
CLK to Data-out high impedance
(CAS latency = 1)
t HZ
—
13
—
15
ns
t HZ
—
7
—
9
ns
1, 4
Data-in setup time
t DS
2
—
3
—
ns
1
Data in hold time
t DH
1
—
1
—
ns
1
Address setup time
t AS
2
—
3
—
ns
1
Address hold time
t AH
1
—
1
—
ns
1
CKE setup time
t CES
2
—
3
—
ns
1, 5
CKE setup time for power down exit
t CESP
2
—
3
—
ns
1
CKE hold time
t CEH
1
—
1
—
ns
1
Command (CS, RAS, CAS, WE, DQM)
setup time
t CS
2
—
3
—
ns
1
Command (CS, RAS, CAS, WE, DQM)
hold time
t CH
1
—
1
—
ns
1
(CAS latency = 2, 3)
43
HM5216805 Series, HM5216405 Series
AC Characteristics (Ta = 0 to 70°C, VCC, VCCQ = 3.3 V ± 0.3 V, VSS, VSSQ = 0 V) (cont)
HM5216805/HM5216405
-10H
Parameter
Min
Max
Min
Max
Unit
Notes
Ref/Active to Ref/Active command period t RC
90
—
100
—
ns
1
Active to Precharge command period
t RAS
60
120000
70
120000
ns
1
Active to precharge on full page mode
t RASC
—
120000
—
120000
ns
1
Active command to column command
(same bank)
t RCD
30
—
30
—
ns
1
Precharge to active command period
t RP
30
—
30
—
ns
1
Write recovery or data-in to precharge
lead time
t DPL
15
—
15
—
ns
1
Active (a) to Active (b) command period
t RRD
20
—
20
—
ns
1
Transition time (rise to fall)
tT
1
5
1
5
ns
Refresh period
t REF
—
64
—
64
ms
Notes: 1.
2.
3.
4.
5.
Symbol
-12
AC measurement assumes t T = 1 ns. Reference level for timing of input signals is 1.40 V.
Access time is measured at 1.40 V. Load condition is C L = 50 pF with current source.
t LZ (max) defines the time at which the outputs achieves the low impedance state.
t HZ (max) defines the time at which the outputs achieves the high impedance state.
t CES defines CKE setup time to CKE rising edge except power down exit command.
Test Conditions
• Input and output timing reference level: 1.4 V
• Input waveform and output load: See following figures
2.8 V
80%
input
I/O
50 Ω
20%
V SS
+1.4 V
CL
t
44
T
tT
HM5216805 Series, HM5216405 Series
Relationship Between Frequency and Minimum Latency
HM5216805/HM5216405
Parameter
Frequency (MHz)
tCK (ns)
-10H
-12
100
10
66
15
33
30
83
12
55
18
28
36
Notes
Active command to column command (same t RCD
bank)
3
2
1
3
2
1
1
Active command to active command (same
bank)
t RC
9
6
3
9
6
3
= [tRAS + tRP]
1
Active command to precharge command
(same bank)
t RAS
6
4
2
6
4
2
1
Precharge command to active command
(same bank)
t RP
3
2
1
3
2
1
1
Write recovery or data-in to precharge
command (same bank)
t DPL
2
1
1
2
1
1
1
Active command to active command
(different bank)
t RRD
2
2
1
2
2
1
1
Self refresh exit time
I SREX
2
2
2
2
2
2
2
Last data in to active command
(Auto precharge, same bank)
I APW
5
3
2
5
3
2
= [tDPL + tRP]
Self refresh exit to command input
I SEC
9
6
3
9
6
3
= [tRC]
Precharge command to high impedance
(CAS latency = 3)
I HZP
3
3
3
3
3
3
(CAS latency = 2)
I HZP
—
2
2
—
2
2
(CAS latency = 1)
I HZP
—
—
1
—
—
1
I APR
1
1
1
1
1
1
–2
–2
–2
–2
–2
–2
Last data out to active command (auto
precharge) (same bank)
Symbol
Last data out to precharge (early precharge)
(CAS latency = 3)
I EP
(CAS latency = 2)
I EP
—
–1
–1
—
–1
–1
(CAS latency = 1)
I EP
—
—
0
—
—
0
Column command to column command
I CCD
1
1
1
1
1
1
Write command to data in latency
I WCD
0
0
0
0
0
0
DQM to data in
I DID
0
0
0
0
0
0
DQM to data out
I DOD
2
2
2
2
2
2
CKE to CLK disable
I CLE
1
1
1
1
1
1
45
HM5216805 Series, HM5216405 Series
Relationship Between Frequency and Minimum Latency (cont)
HM5216805/HM5216405
Parameter
-10H
-12
Frequency (MHz)
tCK (ns)
Symbol
100
10
66
15
33
30
83
12
55
18
28
36
Register set to active command
t RSA
1
1
1
1
1
1
CS to command disable
I CDD
0
0
0
0
0
0
Power down exit to command input
I PEC
1
1
1
1
1
1
Burst stop to output valid data hold (CAS
latency = 3)
I BSR
2
2
2
2
2
2
(CAS latency = 2)
I BSR
—
1
1
—
1
1
(CAS latency = 1)
I BSR
—
—
0
—
—
0
I BSH
3
3
3
3
3
3
(CAS latency = 2)
I BSH
—
2
2
—
2
2
(CAS latency = 1)
I BSH
—
—
1
—
—
1
I BSW
0
0
0
0
0
0
Burst stop to output high impedance (CAS
latency = 3)
Burst stop to write data ignore
Notes
Notes: 1. t RCD to tRRD are recommended value.
2. When self refresh exit is executed, CKE should be kept “H” longer than l SREX from exit cycle.
46
HM5216805 Series, HM5216405 Series
Timing Waveforms
Read Cycle
t CK
t CKH t CKL
CLK
t RC
VIH
CKE
t CS t CH
t RP
t RAS
t RCD
t CS t CH
t CS t CH
t CS t CH
t CS t CH
t CS t CH
t CS t CH
t CS t CH
CS
t CS t CH
t CS t CH
RAS
t CS t CH
t CS t CH
CAS
t CS t CH
t CS t CH
t AS t AH
t AS t AH
t AS t AH
t AS t AH
t AS t AH
t CS t CH
t CS t CH
WE
t AS t AH
A11
t AS t AH
t AS t AH
A10
t AS t AH
t AS t AH
t AS t AH
Address
t CH
t CS
DQMU
/DQML
I/O(input)
t AC
I/O(output)
t AC
t AC
t AC
Bank 0
Active
Bank 0
Read
t LZ
t OH
t OH
t OH
Bank 0
Precharge
t HZ
Burst length = 4
Bank0 Access
= VIH or VIL
47
HM5216805 Series, HM5216405 Series
Write Cycle
t CK
t CKH t CKL
CLK
t RC
VIH
CKE
t RAS
t RCD
t CS t CH
t RP
t CS t CH
t CS t CH
t CS t CH
t CS t CH
t CS t CH
t CS t CH
t CS t CH
CS
t CS t CH
t CS t CH
RAS
t CS t CH
t CS t CH
CAS
t CS t CH
t CS t CH
t CS t CH
t AS t AH
t AS t AH
t AS t AH
t AS t AH
t CS t CH
WE
t AS t AH
t AS t AH
A11
t AS t AH
t AS t AH
A10
t AS t AH
t AS t AH
t AS t AH
Address
t CS
t CH
DQMU
/DQML
t DS t DH tDS
t DH t DS t DH t DS
t DH
I/O(input)
t RWL
I/O(output)
Bank 0
Active
48
Bank 0
Write
Bank 0
Precharge
Burst length = 4
Bank0 Access
= VIH or VIL
HM5216805 Series, HM5216405 Series
Mode Register Set Cycle
0
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
CLK
CKE
VIH
CS
RAS
CAS
WE
A11(BS)
Address
code R: b
valid
C: b’
C: b
DQMU
/DQML
I/O(output)
b
b+3
b’
b’+1
b’+2
b’+3
High-Z
I/O(input)
t RP
Precharge
If needed
t RSA
Mode
Bank 1
register Active
Set
t RCD
Output mask
Bank 1
Read
tRCD = 3
CAS Latency = 3
Burst Length = 4
= VIH or VIL
49
HM5216805 Series, HM5216405 Series
Read Cycle/Write Cycle
0
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
CLK
CKE
Read cycle
RAS-CAS delay = 3
CAS Latency = 3
Burst Length = 4
= VIH or VIL
VIH
CS
RAS
CAS
WE
A11(BS)
Address
DQMU
/DQML
I/O
(output)
I/O
(input)
CKE
R:a
C:a
R:b
C:b
a
C:b'
a+1 a+2 a+3
b
C:b"
b+1 b+2 b+3 b'
b'+1 b"
b"+1 b"+2 b"+3
High-Z
Bank 0
Active
Bank 0
Read
Bank 1
Active
Bank 1 Bank 0
Read
Precharge
Bank 1
Read
Bank 1
Read
Bank 1
Precharge
VIH
Write cycle
RAS-CAS delay = 3
CAS Latency = 3
Burst Length = 4
= VIH or VIL
CS
RAS
CAS
WE
A11(BS)
Address
DQMU
/DQML
I/O
(output)
I/O
(input)
50
R:a
C:a
R:b
C:b
C:b'
C:b"
High-Z
a
Bank 0
Active
Bank 0
Write
a+1 a+2 a+3
Bank 1
Active
b
Bank 1
Write
b+1 b+2 b+3 b'
Bank 0
Precharge
Bank 1
Write
b'+1 b"
Bank 1
Write
b"+1 b"+2 b"+3
Bank 1
Precharge
HM5216805 Series, HM5216405 Series
Read/Single Write Cycle
0
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
CLK
CKE
VIH
CS
RAS
CAS
WE
A11(BS)
Address
DQMU
/DQML
I/O
(input)
I/O
(output)
CKE
R:a
C:a
R:b
C:a' C:a
a
a
Bank 0
Active
Bank 0
Read
Bank 1
Active
C:a
R:b
a+1 a+2 a+3
a
Bank 0 Bank 0
Write
Read
a+1 a+2 a+3
Bank 0
Precharge
Bank 1
Precharge
VIH
CS
RAS
CAS
WE
A11(BS)
R:a
C:a
C:b C:c
Address
DQMU
/DQML
I/O
(input)
I/O
(output)
a
a
Bank 0
Active
Bank 0
Read
Bank 1
Active
a+1
b
c
a+3
Bank 0
Write
Bank 0 Bank 0
Write Write
Bank 0
Precharge
Read/Single write
RAS-CAS delay = 3
CAS Latency = 3
Burst Length = 4
= VIH or VIL
51
HM5216805 Series, HM5216405 Series
Read/Burst Write Cycle
0
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
CLK
CKE
CS
RAS
CAS
WE
A11(BS)
Address
DQMU
/DQML
I/Q
(input)
I/Q
(output)
CKE
R:a
C:a
R:b
C:a
a a+1 a+2 a+3
a a+1 a+2
Bank 0
Active
Bank 0
Read
Bank 1
Active
a+3
Clock
Suspend
Bank 0
Write
Bank 0
Precharge
Bank 1
Precharge
VIH
CS
RAS
CAS
WE
A11(BS)
Address
DQMU
/DQML
I/Q
(input)
I/Q
(output)
R:a
C:a
R:b
C:a
a a+1 a+2 a+3
a a+1
Bank 0
Active
Bank 0
Read
Bank 1
Active
a+3
Bank 0
Write
Bank 0
Precharge
Read/Burst write
RAS-CAS delay = 3
CAS Latency = 4
Burst Length = 4
= VIH or VIL
52
HM5216805 Series, HM5216405 Series
Full Page Read/Write Cycle
0
1
2
3
4
5
6
7
8
9
260 261 262 263 264 265 266 267 268 269
CLK
CKE
VIH
Read cycle
RAS-CAS delay = 3
CAS Latency = 3
Burst Length = full page
= VIH or VIL
CS
RAS
CAS
WE
A11(BS)
Address
DQMU
/DQML
I/O
(output)
I/O
(input)
CKE
R:a
C:a
R:b
a
a+1
a+2
a+3
a-2
a-1
a
a+1
a+2
a+3
a+4
a+5
High-Z
Bank 0
Active
Bank 0
Read
Bank 1
Active
Burst stop
Bank 1
Precharge
VIH
Write cycle
RAS-CAS delay = 3
CAS Latency = 3
Burst Length = full page
= VIH or VIL
CS
RAS
CAS
WE
A11(BS)
Address
DQMU
/DQML
I/O
(output)
I/O
(input)
R:a
C:a
R:b
High-Z
a
Bank 0
Active
Bank 0
Write
a+1
a+2
Bank 1
Active
a+3
a+4
a+5
a+6
a+1
a+2
a+3
a+4
a+5
Burst stop
Bank 1
Precharge
53
HM5216805 Series, HM5216405 Series
Auto Refresh Cycle
0
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
a
a+1
CLK
CKE
VIH
CS
RAS
CAS
WE
A11(BS)
Address
C:a
R:a
A10=1
DQMU
/DQML
I/O(input)
High-Z
I/O(output)
t RC
t RP
Auto Refresh
Precharge
If needed
tRC
Auto Refresh
Active
Bank 0
Read
Bank 0
Refresh cycle and
Read cycle
RAS-CAS delay=2
CAS latency=2
Burst length=4
= VIH or VIL
Self Refresh Cycle
CLK
ISREX
CKE
CKE Low
CKE High
CS
RAS
CAS
WE
A11(BS)
Address
DQMU
/DQML
I/O(imput)
I/O(output)
A10=1
High-Z
tRP
Precharge command
If needed
54
tRC
Self refresh entry
command
Self refresh exit
ignore command
or No operation
Next Self refresh entry
clock command
enable
Next Auto
clock refresh
enable
Self refresh cycle
RAS-CAS delay = 3
CAS Latency = 3
Burst Length = 4
=VIH or VIL
HM5216805 Series, HM5216405 Series
Clock Suspend Mode
t CESP
0
1
2
3
4
5
t CES
t CEH
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
CLK
CKE
Read cycle
RAS-CAS delay=2
CAS latency=2
Burst length=4
= VIH or VIL
CS
RAS
CAS
WE
A11(BS)
Address
DQMU
/DQML
I/O
(output)
I/O
(input)
R:a
C:a
R:b
a
C:b
a+1 a+2
a+3
b
b+1 b+2 b+3
High-Z
Bank0 Active clock
Active suspend start
Active clock Bank0
suspend end Read
Bank1
Active
Read suspend
start
Read suspend
end
Bank1
Read
Bank0
Precharge
Earliest Bank1
Precharge
CKE
Write cycle
RAS-CAS delay=2
CAS latency=2
Burst length=4
= VIH or VIL
CS
RAS
CAS
WE
A11(BS)
Address
DQMU
/DQML
I/O
(output)
I/O
(input)
C:a R:b
R:a
C:b
High-Z
a
Bank0
Active
Active clock
suspend start
a+1 a+2
Active clock Bank0 Bank1
supend end Write Active
Write suspend
start
a+3 b
Write suspend
end
b+1 b+2 b+3
Bank1 Bank0
Write Precharge
Earliest Bank1
Precharge
55
HM5216805 Series, HM5216405 Series
Power Down Mode
CLK
CKE Low
CKE
CS
RAS
CAS
WE
A11(BS)
Address
R: a
A10=1
DQMU
/DQML
I/O(input)
High-Z
I/O(output)
Power down cycle
RAS-CAS delay=3
CAS latency=2
Burst length=4
= VIH or VIL
tRP
Power down entry
Precharge command
If needed
Power down
mode exit
Active Bank 0
Power Up Sequence
0
1
2
3
4
5
6
7
8
9
10
48
49
50
51
52
53
54
55
CLK
CKE
VIH
CS
RAS
CAS
WE
Address
DQMU
/DQML
Valld
code
VIH
High-Z
I/O
tRP
All banks
Auto Refresh
Precharge
56
Valld
tRC
tRC
Auto Refresh
tRSA
Mode register Bank active
Set
If needed
HM5216805 Series, HM5216405 Series
Package Dimensions
HM5216805TT/HM5216405TT Series (TTP-44DE)
Unit: mm
18.41
18.81 Max
23
10.16
44
0.80
0.27 ± 0.07
0.25 ± 0.05
22
0.80
0.13 M
11.76 ± 0.20
1.005 Max
Dimension including the plating thickness
Base material dimension
0.13 ± 0.05
0.10
0.145 ± 0.05
0.125 ± 0.04
1.20 Max
0° – 5°
0.50 ± 0.10
Hitachi Code
JEDEC
EIAJ
Weight (reference value)
0.68
1
TTP-44DE
—
—
0.43 g
57
HM5216805 Series, HM5216405 Series
When using this document, keep the following in mind:
1. This document may, wholly or partially, be subject to change without notice.
2. All rights are reserved: No one is permitted to reproduce or duplicate, in any form, the whole or part of
this document without Hitachi’s permission.
3. Hitachi will not be held responsible for any damage to the user that may result from accidents or any
other reasons during operation of the user’s unit according to this document.
4. Circuitry and other examples described herein are meant merely to indicate the characteristics and
performance of Hitachi’s semiconductor products. Hitachi assumes no responsibility for any intellectual
property claims or other problems that may result from applications based on the examples described
herein.
5. No license is granted by implication or otherwise under any patents or other rights of any third party or
Hitachi, Ltd.
6. MEDICAL APPLICATIONS: Hitachi’s products are not authorized for use in MEDICAL
APPLICATIONS without the written consent of the appropriate officer of Hitachi’s sales company.
Such use includes, but is not limited to, use in life support systems. Buyers of Hitachi’s products are
requested to notify the relevant Hitachi sales offices when planning to use the products in MEDICAL
APPLICATIONS.
Hitachi, Ltd.
Semiconductor & IC Div.
Nippon Bldg., 2-6-2, Ohte-machi, Chiyoda-ku, Tokyo 100, Japan
Tel: Tokyo (03) 3270-2111
Fax: (03) 3270-5109
For further information write to:
Hitachi America, Ltd.
Semiconductor & IC Div.
2000 Sierra Point Parkway
Brisbane, CA. 94005-1835
USA
Tel: 415-589-8300
Fax: 415-583-4207
Hitachi Europe GmbH
Continental Europe
Dornacher Straße 3
D-85622 Feldkirchen
München
Tel: 089-9 91 80-0
Fax: 089-9 29 30-00
Hitachi Europe Ltd.
Electronic Components Div.
Northern Europe Headquarters
Whitebrook Park
Lower Cookham Road
Maidenhead
Berkshire SL6 8YA
United Kingdom
Tel: 01628-585000
Fax: 01628-585160
Hitachi Asia Pte. Ltd.
16 Collyer Quay #20-00
Hitachi Tower
Singapore 049318
Tel: 535-2100
Fax: 535-1533
Hitachi Asia (Hong Kong) Ltd.
Unit 706, North Tower,
World Finance Centre,
Harbour City, Canton Road
Tsim Sha Tsui, Kowloon
Hong Kong
Tel: 27359218
Fax: 27306071
Copyright © Hitachi, Ltd., 1997. All rights reserved. Printed in Japan.
58
HM5216805 Series, HM5216405 Series
Revision Record
Rev. Date
Contents of Modification
Drawn by
Approved by
0.0
Initial issue
S. Ishikawa
T. Kizaki
T. Kizaki
T. Kizaki
Nov. 4, 1994
0.1
Feb. 22, 1995 Addition of Full-page Burst Stop
Command Truth Table
Addition of BST: H/X/L/H/H/L/X/X/X
Addition of description for burst stop in full page
Function Truth Table
Addition of BST: L/H/H/L/X
Change of Simplified State Diagram and Mode
Register Configuration
DC Characteristics
ICC2 max: 40/35/30 mA to 30/25/20 mA
ICC3 max: 40/35/30 mA to 35/30/25 mA
AC Characteristics
tRWL min: 20/24/30 ns to 15/18/22.5 ns
Relationship Between Frequency and Minimum Latency
tRWL: 2/2/1/2/2/1/2/2/1 to 2/1/1/2/1/1/2/1/1
Addition of l BSR (CL = 3): 2/2/2/2/2/2/2/2/2
Addition of l BSR (CL = 2): —/1/1/—/1/1/—/1/1
Addition of l BSR (CL = 1): —/—/0/—/—/0/—/—/0
Addition of l BSH (CL = 3): 3/3/3/3/3/3/3/3/3
Addition of l BSH (CL = 2): —/2/2/—/2/2/—/2/2
Addition of l BSH (CL = 1): —/—/1/—/—/1/—/—/1
Addition of l BSW : 0/0/0/0/0/0/0/0/0
Timing Waveforms: Addition of Full Page Read/Write cycle
S. Ishikawa
0.2
Aug, 4, 1995
S. Ishikawa
1.0
Oct. 20, 1995 Correct errors
DC Characteristics
ICC2 max: 30/25/20 mA to 40/35/30 mA
ICC3 max: 35/30/25 mA to 45/40/35 mA
AC Characteristics
tHZ min: 2/3/3 ns to 2/2/2 ns
Relationship Between Frequency and Minimum Latency
Change of notes 2
Unification of HM5216805 Series and HM5216405 Series
Operation of HM5216805 Series, HM5216405 Series
Addition of figure for READ to WRITE Command
Interval (2)
Absolute Maximum Ratings: Addition of note1
AC Characteristics
tAC (CL = 1) max: 28/32/36 ns to 27/32/36 ns
tAC (CL = 2) max: 13/15/17 ns to 12/15/17 ns
tCESP min: 5/5/5 ns to 2/3/3 ns
Relationship Between Frequency and Minimum Latency
Addition of l SREX : 2/2/2/2/2/2/2/2/2
lAPW: 5/4/2/5/4/2/5/4/2 to 5/3/2/5/3/2/5/3/2
Addition of notes3
Timing Waveforms
Change of Self Refresh Cycle
K. Nishimoto T. Kizaki
59
HM5216805 Series, HM5216405 Series
Rev. Date
Contents of Modification
Drawn by
Approved by
2.0
Dec. 10, 1996 Addition of HM5216805/5216405-10H Series
Capacitance
C|1, C|2: — typ to 2 min
C|3: — typ to 2 min
AC Characteristics
Addition of tAC (CL = 2) (HM5216805/5216405-10H)
max: 9.0/12/17 ns
tAC (CL = 2) max: 12/15/17 ns to 9.5/12/17 ns
tAC (CL = 3) max: 8/10/12 ns to 7.5/9/12 ns
tHZ min: 2/2/2 ns to —/—/— ns
Change of symbol: t RWL to tDPL
T. Takemura S. Ishikawa
3.0
Jan. 20, 1997 Addition of HM5216805/5216405L-10H/10 Series
Change of description for Self-refresh
DC Characteristics
Addition of ICC6 (L-version) max: 250/—/— µA
T. Takemura S. Ishikawa
4.0
Jun. 12, 1997 Deletion of HM5216805/5216405-10/15 Series
T. Takemura S. Ishikawa
5.0
Nov. 1997
60
Change of Subtitle