Precision Edge® PrecisionSY10ELT23 Edge® SY100ELT23 DUAL DIFFERENTIAL PECL-to-TTL TRANSLATOR Micrel SY10ELT23 SY100ELT23 FEATURES ■ ■ ■ ■ ■ ■ ■ 3.0ns typical propagation delay <500ps typical output-to-output skew Differential PECL inputs 24mA TTL outputs Flow-through pinouts Internal input 50kΩ pulldown resistors Available in 8-pin SOIC package Precision Edge® DESCRIPTION The SY10/100ELT23 are dual differential PECL-to-TTL translators. Because PECL (Positive ECL) levels are used, only +5V and ground are required. The small outline 8-lead SOIC package and the low skew dual gate design of the ELT23 makes it ideal for applications which require the translation of a clock and a data signal. The ELT23 is available in both ECL standards: the 10ELT is compatible with positive ECL 10H logic levels, while the 100ELT is compatible with positive ECL 100K logic levels. PIN CONFIGURATION/BLOCK DIAGRAM D0 1 8 VCC D0 2 7 Q0 PECL PIN NAMES TTL D1 3 6 Q1 D1 4 5 GND Pin SOIC TOP VIEW Function Qn TTL Outputs Dn Differential PECL Inputs VCC +5.0V Supply GND Ground Precision Edge is a registered trademark of Micrel, Inc. Rev.: J 1 Amendment: 0 Issue Date: February 2008 Precision Edge® SY10ELT23 SY100ELT23 Micrel ABSOLUTE MAXIMUM RATINGS(1) Symbol TRUTH TABLE Value Unit D D Q –0.5 to +7.0 V L H L 0V to VCC+0.5 V H L H Open Open L Paramter VCC Power Supply Voltage VI PECL Input Voltage VO Voltage Applied to Output at HIGH State –0.5 to +5.5 V IO Current Applied to Output at LOW State Twice the Rated IOL mA Tstore Storage Temperature –65 to +150 °C TA Operating Temperature –40 to +85 °C Note: 1. Permanent device damage may occur if ABSOLUTE MAXIMUM RATINGS are exceeded. This is a stress rating only and functional operation is not implied at conditions other than those detailed in the operational sections of this data sheet. Exposure to ABSOLUTE MAXIMUM RATlNG conditions for extended periods may affect device reliability. DC ELECTRICAL CHARACTERISTICS(1) VCC = VCC (Min.) to VCC (Max.) TA = -40°C Symbol ICC Parameter Power Supply Current Note: 1. Parametric values specified at: TA = +25°C TA = +85°C Min. Max. Min. TA = 0°C Max. Min. Max. Min. Max. Unit Condition — 30 — 30 — 30 — 30 mA — 5 volt Power Supply Range 100ELT23 Series: 10ELT23 Series +4.5V to +5.5V. +4.75V to +5.5V. AC ELECTRICAL CHARACTERISTICS(1) VCC = VCC (Min.) to VCC (Max.) TA = -40°C Symbol Parameter TA = 0°C TA = +25°C TA = +85°C Min. Max. Min. Max. Min. Max. Min. Max. Unit Condition tPLH tPHL Propagation Delay D to Output Q 2.5 3.5 2.5 3.5 2.5 3.5 2.5 3.5 ns CL = 50pF tskpp Part-to-Part Skew(2,5) — 0.5 — 0.5 — 0.5 — 0.5 ns CL = 50pF tskew++ Within-Device Skew(3,5) — 0.3 — 0.3 — 0.3 — 0.3 ns CL = 50pF tskew– – Within-Device Skew(4,5) — 0.3 — 0.3 — 0.3 — 0.3 ns CL = 50pF tr tf Output Rise/Fall Time 1.0V to 2.0V — 1.5 — 1.5 — 1.5 — 1.5 ns CL = 50pF fMAX Maximum Input Frequency(5) 160 — 160 — 160 — 160 — MHz CL = 50pF Notes: 1. Parametric values specified at: 2. 3. 4. 5. 5 volt Power Supply Range 100ELT23 Series: 10ELT23 Series Device-to-Device Skew considering HIGH-to-HIGH transitions at common VCC level. Within-Device Skew considering HIGH-to-HIGH transitions at common VCC level. Within-Device Skew considering LOW-to-LOW transitions at common VCC level. These parameters are guaranteed but not tested. 2 +4.5V to +5.5V. +4.75V to +5.5V. Precision Edge® SY10ELT23 SY100ELT23 Micrel TTL DC ELECTRICAL CHARACTERISTICS(1) VCC = VCC (Min.) to VCC (Max.) TA = -40°C Symbol Parameter VOH Output HIGH Voltage VOL Output LOW Voltage IOS Output Short Circuit Current Note: 1. Parametric values specified at: TA = +25°C TA = +85°C Min. Max. Min. TA = 0°C Max. Min. Max. Min. Max. Unit Condition 2.5 2.0 — — 2.5 2.0 — — 2.5 2.0 — — 2.5 2.0 — — V V IOH = –3.0mA IOH = –15mA — 0.5 — 0.5 — 0.5 — 0.5 V IOL = 24mA –80 –200 –80 –200 –80 –200 –80 –200 mA VOUT = 0V 5 volt Power Supply Range 100ELT23 Series: 10ELT23 Series +4.5V to +5.5V. +4.75V to +5.5V. PECL DC ELECTRICAL CHARACTERISTICS(1) VCC = VCC (Min.) to VCC (Max.) TA = -40°C Symbol Parameter TA = 0°C TA = +25°C TA = +85°C Min. Typ. Max. Min. Typ. Max. Min. Typ. Max. Min. Typ. Max. Unit IIH Input HIGH Current — — 150 — — 150 — — 150 — — 150 µA IIL Input HIGH Current 0.5 — — 0.5 — — 0.5 — — 0.5 — — µA VCMR Common Mode Range 2.2 — VCC 2.2 — VCC 2.2 — VCC 2.2 — VCC V VPP Minimum Peak-to-Peak Input(2) 200 — — 200 — — 200 — — 200 — — mV 10ELT 3770 100ELT 3835 — — 4110 4120 3830 3835 — — 4160 4120 3870 3835 — — 4190 4120 3940 3835 — — 4280 4120 Input LOW Voltage(3) 10ELT 3050 100ELT 3190 — — 3500 3525 3050 3190 — — 3520 3525 3050 3190 — — 3520 3525 3050 3190 — — 3555 3525 VIH VIL Input HIGH Voltage(3) Notes: 1. Parametric values specified at: mV mV 5 volt Power Supply Range 100ELT23 Series: 10ELT23 Series 2. 200mV input guarantees full logic at output. 3. These values are for VCC = 5.0V. Level Specifications will vary 1:1 VCC. 3 +4.5V to +5.5V. +4.75V to +5.5V. Precision Edge® SY10ELT23 SY100ELT23 Micrel PRODUCT ORDERING CODE Package Type Operating Range Package Marking Lead Finish SY10ELT23ZC Z8-1 Commercial HEL23 Standard SY10ELT23ZCTR(1) Z8-1 Commercial HEL23 Standard SY100ELT23ZC Z8-1 Commercial XEL23 Standard SY100ELT23ZCTR(1) Z8-1 Commercial XEL23 Standard SY10ELT23ZI Z8-1 Industrial HEL23 Standard SY10ELT23ZITR(1) Z8-1 Industrial HEL23 Standard SY100ELT23ZI Z8-1 Industrial XEL23 Standard SY100ELT23ZITR(1) Z8-1 Industrial XEL23 Standard SY10ELT23ZG(2,3) Z8-1 Industrial HEL23 Pb-Free NiPdAu SY10ELT23ZGTR(1,2,3) Z8-1 Industrial HEL23 Pb-Free NiPdAu SY100ELT23ZG(2,3) Z8-1 Industrial XEL23 Pb-Free NiPdAu SY100ELT23ZGTR(1,2,3) Z8-1 Industrial XEL23 Pb-Free NiPdAu Part Number Notes: 1. Tape and Reel. 2. Recommended for new designs. 3. Pb-Free version. 4 Precision Edge® SY10ELT23 SY100ELT23 Micrel 8 LEAD SOIC .150" WIDE (Z8-1) Rev. 03 MICREL, INC. 1849 FORTUNE DRIVE SAN JOSE, CA 95131 TEL + 1 (408) 944-0800 FAX + 1 (408) 944-0970 WEB USA http://www.micrel.com The information furnished by Micrel in this datasheet is believed to be accurate and reliable. However, no responsibility is assumed by Micrel for its use. Micrel reserves the right to change circuitry and specifications at any time without notification to the customer. Micrel Products are not designed or authorized for use as components in life support appliances, devices or systems where malfunction of a product can reasonably be expected to result in personal injury. Life support devices or systems are devices or systems that (a) are intended for surgical implant into the body or (b) support or sustain life, and whose failure to perform can be reasonably expected to result in a significant injury to the user. A Purchaser’s use or sale of Micrel Products for use in life support appliances, devices or systems is at Purchaser’s own risk and Purchaser agrees to fully indemnify Micrel for any damages resulting from such use or sale. © 2003 Micrel, Incorporated. 5