MITSUBISHI MICROCOMPUTERS 7630 Group SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER z z DESCRIPTION The 7630 group is a single chip 8-bit microcomputer designed with CMOS silicon gate technology. Being equipped with a CAN (Controller Area Network) module circuit, the microcomputer is suited to drive automotive equipments. The CAN module complies with CAN specification version 2.0, part B and allows priority-based message management. In addition to the microcomputers simple instruction set, the ROM, RAM and I/O addresses are placed in the same memory map to enable easy programming. The built-in ROM is available as mask ROM or One Time PROM. For development purposes, emulator- and EPROM-type microcomputers are available as well. z z z z z z z FEATURES z z z z Interrupts . . . . . . . . . . . . . . . . . . . . . . . . 24 sources, 24 vectors Timers 16-bit Timers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 channels 8-bit Timers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 channels Serial I/Os Clock synchronous. . . . . . . . . . . . . . . . . . . . . . . . . . . 1 channel UART . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 channel CAN module (CAN specification version 2.0, part B) . . . . . . . . . . . 1 channel A-D converter . . . . . . . . . . . . . . . . . . . . . . . . 8-bits x 8 channels Watchdog timer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 Clock Generating Circuit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 Built-in with internal feedback resistor Power source voltage (at 10 MHz oscillation frequency). . . . . . . . . . . . . . . 4.0 to 5.5 V Power dissipation In high-speed mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . 55 mW (at 8 MHz oscillation frequency, at 5 V power source voltage) Operating temperature range. . . . . . . . . . . . . . . . . –40 to 85 °C Package . . . . . . . . . . . . . . . . . . . . . . . . . . . . 44QFP (44P6N-A) Basic machine-language instructions . . . . . . . . . . . . . . . . . . 71 Minimum instruction execution time (at 10 MHz oscillation frequency) . . . . . . . . . . . . . . . . . . 0.2 µs Memory size ROM . . . . . . . . . . . . . . . . . 16252 bytes (M37630M4T-XXXFP) RAM . . . . . . . . . . . . . . . . . . . 512 bytes (M37630M4T-XXXFP) I/O ports Programmable I/O ports . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35 Input . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 z z APPLICATION Automotive controls P11/INT0 P07/AN7 P06/AN6 P05/AN5 P04/AN4 P03/AN3 27 26 25 24 23 P12/INT1 29 28 P14/CNTR0 P13/TX0 30 P15/CNTR1 32 31 P16/PWM 33 PIN CONFIGURATION (TOP VIEW) P17 P20/SIN P21/SOUT P22/SCLK P23/SRDY VSS P24/URXD P25/UTXD 34 22 35 21 36 20 41 15 P26/URTS P27/UCTS P30 42 14 43 13 44 12 19 37 M37630M4T-XXXFP 38 39 18 17 M37630E4T-XXXFP 1 2 3 4 5 6 7 8 9 10 11 P31/CTX P33 P34 P40/KW0 P41/KW1 P42/KW2 P43/KW3 P44/KW4 P45/KW5 P46/KW6 16 P32/CRX 40 P02/AN2 P01/AN1 P00/AN0 VREF AVSS VCC XOUT XIN VSS RESET P47/KW7 Package type: 44P6N-A 44-pin plastic molded QFP Fig. 1 Pin configuration of M37630M4T–XXXFP MITSUBISHI ELECTRIC 1 Fig. 2 2 M37630MXT-XXXFP FUNCTIONAL BLOCK DIAGRAM (PACKAGE: 44P6N-A) Functional block diagram Clock output XOUT Clock input XIN Reset input RESET VCC 16 15 13 17 VSS 14 AVSS 39 18 Clock generating circuit CPU A (8) ROM RAM WDT X (8) Timer X (16) Timer 1 (8) Timer Y (16) Timer 2 (8) 2 Y (8) S (8) PCH (8) PWM Timer 3 (8) PCL (8) PS (8) MITSUBISHI ELECTRIC CAN UART 2 Serial I/O 4 A-D Converter INT0, INT1 4 8 2 P2 (8) 12 11 10 9 8 7 6 5 4 3 2 1 44 43 42 41 40 38 37 36 35 3 P1 (7) 34 33 32 31 30 29 28 P0 (8) 19 27 26 25 24 23 22 21 20 VREF input I/O port P4 I/O port P3 I/O port P2 I/O port P1 I/O port P0 MITSUBISHI MICROCOMPUTERS P3 (5) 7630 Group P4 (8) SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER key on wake up MITSUBISHI MICROCOMPUTERS 7630 Group SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER PIN DESCRIPTION Table 1: Pin description Pin Name Input/Output Description VCC, VSS Power source voltage Power supply pins; apply 4.0 to 5.5 V to VCC and 0 V to VSS AVSS Analog power source voltage Ground pin for A-D converter. Connect to VSS RESET Reset input Input XIN Clock input Input XOUT Clock output Output Input and output pins of the internal clock generating circuit. Connect a ceramic or quartz–crystal resonator between the XIN and XOUT pins. When an external clock source is used, connect it to XIN and leave XOUT open. VREF Reference voltage input Input Reference voltage input pin for A-D converter P00/AN0— P07/AN7 I/O port P0 I/O CMOS I/O ports or analog input ports Input CMOS input port or external interrupt input port. The active edge (rising or falling) of external interrupts can be selected. This pin will be used as VPP pin during PROM programming of One Time PROM Versions. P11/INT0 Reset pin. This pin must be kept at “L” level for more than 2 µs, to enter the reset state. If the crystal or ceramic resonator requires more time to stabilize, extend the “L” level period. P12/INT1 CMOS I/O port or external interrupt input port. The active edge (rising or falling) of external interrupts can be selected. P13/TX0 CMOS I/O port or input pin used in the bi-phase counter mode P14/CNTR0 I/O port P1 I/O CMOS I/O port or timer X input pin used for the event counter, pulse width measurement and bi-phase counter mode P15/CNTR1 CMOS I/O port or timer Y input pin used for the event counter, pulse width and pulse period measurement mode P16/PWM CMOS I/O port or PWM output pin used in the PWM mode of timers 2 and 3 P17 CMOS I/O port P20/SIN P21/SOUT P22/SCLK P23/SRDY CMOS I/O ports or clock synchronous serial I/O pins I/O port P2 I/O P24/URXD P25/UTXD P26/URTS P27/UCTS CMOS I/O ports or asynchronous serial I/O pins P30 CMOS I/O port P31/CTX CMOS I/O port or CAN transmit data pin I/O port P3 I/O P32/CRX CMOS I/O port or CAN receive data pin P33—P34 CMOS I/O port P40/KW0— P47/KW7 I/O port P4 I/O CMOS I/O ports. These ports can be used for key-on wake-up when configured as inputs. MITSUBISHI ELECTRIC 3 MITSUBISHI MICROCOMPUTERS 7630 Group SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER PART NUMBERING Product M37630 M 4 T– XXX FP Package type FP: 44P6N-A package FS: 80D0 package ROM number Omitted in One Time PROM version (blank) and EPROM version T: Automotive use ROM/PROM size 4: 16384 bytes The first 128 bytes and the last 4 bytes of ROM are reserved areas. They cannot be used. Memory type M: Mask ROM version E: EPROM or One Time PROM version Fig. 3 4 Part numbering MITSUBISHI ELECTRIC MITSUBISHI MICROCOMPUTERS 7630 Group SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER GROUP EXPANSION Memory Size Mitsubishi plans to expand the 7630 group as follows: ROM/PROM size . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16 Kbytes RAM size. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 512 bytes Memory Type Package Support mask ROM, One Time PROM and EPROM versions. 44P6N-A . . . . . . . . . . . . . . . . .0.8mm-pitch plastic molded QFP 80D0 . . . . . . . . . . . 0.8mm-pitch ceramic LCC (EPROM version) ROM External 60K 48K 32K 28K 24K 20K Under development M37630M4T 16K 12K M37630E4T Mass product 8K 384 512 640 768 896 1024 RAM size (bytes) Fig. 4 Memory expansion plan Currently supported products are listed below: Table 2: List of supported products Product (P)ROM size (bytes) ROM size for User ( ) As of March 1998 RAM size (bytes) M37630M4T-XXXFP M37630E4T-XXXFP M37630E4FP M37630E4FS Remarks Package Mask ROM version 16384 512 44P6N-A (16252) One Time PROM version One Time PROM version (blank) 80D0 MITSUBISHI ELECTRIC EPROM version 5 MITSUBISHI MICROCOMPUTERS 7630 Group SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER FUNCTIONAL DESCRIPTION Central Processing Unit (CPU) CPU Mode Register CPUM The core of 7630 group microcomputers is the 7600 series CPU. This core is based on the standard instruction set of 740 series; however the performance is improved by allowing to execute the same instructions as that of the 740 series in less cycles. Refer to the 7600 Series Software Manual for details of the instruction set. The CPU mode register contains the stack page selection bit and internal system clock selection bit. The CPU mode register is allocated to address 000016. 7 0 CPU mode register (address 000016) CPUM Processor mode bits (set these bits to “00”) b1 b0 0 0: Single–chip mode 0 1: Not used 1 0: Not used 1 1: Not used Stack page selection bit 0 : 0 page 1 : 1 page Not used (“0” when read, do not write “1”) Internal system clock selection bit 0 : φ=f(XIN) divided by 2 (high–speed mode) 1 : φ=f(XIN) divided by 8 (middle–speed mode) Not used (“0” when read, do not write “1”) Fig. 5 6 Structure of CPU mode register MITSUBISHI ELECTRIC MITSUBISHI MICROCOMPUTERS 7630 Group SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER MEMORY Special Function Register (SFR) Area Interrupt Vector Area The special function register (SFR) area contains the registers relating to functions such as I/O ports and timers. The interrupt vector area is for storing jump destination addresses used at reset or when an interrupt is generated. RAM Zero Page RAM is used for data storage and for stack area of subroutine calls and interrupts. This area can be accessed most efficiently by means of the zero page addressing mode. ROM Special Page ROM is used for storing user’s program code as well as the interrupt vector area. This area can be accessed most efficiently by means of the special page addressing mode. RAM area Address XXXX16 000016 192 011F16 004016 256 015F16 384 01DF16 006016 512 025F16 00FF16 640 02DF16 768 035F16 896 03DF16 1024 045F16 1536 06DF16 2048 085F16 RAM size (byte) CAN SFRs Zero page User RAM XXXX16 086016 ROM area Fig. 6 SFR area Not used ROM size (byte) Address YYYY16 Address ZZZZ16 4096 F00016 F08016 YYYY16 8192 E00016 E08016 ZZZZ16 12288 D00016 D08016 16384 C00016 C08016 20480 B00016 B08016 24576 A00016 A08016 28672 900016 908016 32768 800016 808016 36864 700016 708016 40960 600016 608016 45056 500016 508016 49152 400016 408016 53248 300016 308016 57344 200016 208016 61440 100016 108016 ROM Reserved ROM area FF0016 FFCA16 FFFB16 FFFC16 FFFF16 Interrupt vector area Special page Reserved ROM area Memory map diagram MITSUBISHI ELECTRIC 7 MITSUBISHI MICROCOMPUTERS 7630 Group SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER SPECIAL FUNCTION REGISTERS (SFR) 000016 000116 000216 000316 000416 000516 000616 000716 000816 000916 000A16 000B16 000C16 000D16 CPU mode register Not used Interrupt request register A Interrupt request register B Interrupt request register C Interrupt control register A Interrupt control register B Interrupt control register C Port P0 register Port P0 direction register Port P1 register Port P1 direction register Port P2 register Port P2 direction register 000E16 Port P3 register 000F16 Port P3 direction register 001016 Port P4 register 001116 Port P4 direction register 001216 Serial I/O shift register 001316 Serial I/O control register 001416 A-D conversion register 001516 A-D control register 001616 Timer 1 001716 Timer 2 001816 Timer 3 001916 Timer 123 mode register 001A16 001B16 001C16 001D16 001E16 001F16 002016 002116 002216 002316 002416 002516 002616 002716 002816 002916 002A16 002B16 002C16 002D16 002E16 002F16 Fig. 7 8 Timer XL Timer XH Timer YL Timer YH Timer X mode register Timer Y mode register UART mode register UART baud rate generator UART control register UART status register UART transmit buffer register 1 UART transmit buffer register 2 UART receive buffer register 1 UART receive buffer register 2 Port P0 pull-up control register Port P1 pull-up control register Port P2 pull-up control register Port P3 pull-up control register Port P4 pull-up/down control register Interrupt polarity selection register Watchdog timer register Polarity control register CPUM IREQA IREQB IREQC ICONA ICONB ICONC P0 P0D P1 P1D P2 P2D P3 P3D P4 P4D SIO SIOCON AD ADCON T1 T2 T3 T123M TXL TXH TYL TYH TXM TYM UMOD UBRG UCON USTS UTBR1 UTBR2 URBR1 URBR2 PUP0 PUP1 PUP2 PUP3 PUP4 IPOL WDT PCON 003016 003116 003216 003316 003416 003516 003616 003716 003816 003916 003A16 003B16 003C16 003D16 CAN transmit control register CAN bus timing control register 1 CAN bus timing control register 2 CAN acceptance code register 0 CAN acceptance code register 1 CAN acceptance code register 2 CAN acceptance code register 3 CAN acceptance code register 4 CAN acceptance mask register 0 CAN acceptance mask register 1 CAN acceptance mask register 2 CAN acceptance mask register 3 CAN acceptance mask register 4 CAN receive control register 003E16 CAN transmit abort register 003F16 Reserved 004016 CAN transmit buffer register 0 004116 CAN transmit buffer register 1 004216 CAN transmit buffer register 2 004316 CAN transmit buffer register 3 004416 CAN transmit buffer register 4 004516 CAN transmit buffer register 5 004616 CAN transmit buffer register 6 004716 CAN transmit buffer register 7 004816 CAN transmit buffer register 8 004916 CAN transmit buffer register 9 004A16 004B16 004C16 004D16 004E16 004F16 005016 005116 005216 005316 005416 005516 005616 005716 005816 005916 005A16 005B16 005C16 005D16 005E16 005F16 Memory map of special register (SFR) MITSUBISHI ELECTRIC CAN transmit buffer register A CAN transmit buffer register B CAN transmit buffer register C CAN transmit buffer register D Reserved Reserved CAN receive buffer register 0 CAN receive buffer register 1 CAN receive buffer register 2 CAN receive buffer register 3 CAN receive buffer register 4 CAN receive buffer register 5 CAN receive buffer register 6 CAN receive buffer register 7 CAN receive buffer register 8 CAN receive buffer register 9 CAN receive buffer register A CAN receive buffer register B CAN receive buffer register C CAN receive buffer register D Reserved Reserved CTRM CBTCON1 CBTCON2 CAC0 CAC1 CAC2 CAC3 CAC4 CAM0 CAM1 CAM2 CAM3 CAM4 CREC CABORT CTB0 CTB1 CTB2 CTB3 CTB4 CTB5 CTB6 CTB7 CTB8 CTB9 CTBA CTBB CTBC CTBD CRB0 CRB1 CRB2 CRB3 CRB4 CRB5 CRB6 CRB7 CRB8 CRB9 CRBA CRBB CRBC CRBD MITSUBISHI MICROCOMPUTERS 7630 Group SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER I/O PORTS The 7630 group has 35 programmable I/O pins and one input pin arranged in five I/O ports (ports P0 to P4). The I/O ports are controlled by the corresponding port registers and port direction registers; each I/O pin can be controlled separately. When data is read from a port configured as an output port, the port latch’s contents are read instead of the port level. A port configured 7 as an input port becomes floating and its level can be read. Data written to this port will affect the port latch only; the port remains floating. Refer to Structure of port- and port direction registers, Structure of port I/Os (1) and Structure of port I/Os (2). 0 Port Pi register (i = 0 to 4) (address 000816 + 2 · i) Pi Port Pij control bit (j = 0 to 7) 0 : “L” level 1 : “H” level Note : 7 The control bits corresponding to P10, P35, P36 and P37 are not used (“0” when read, do not write “1”). 0 Port Pi direction register (i = 0 to 4) (address 000916 + 2 · i) PiD Port Pij direction control bit (j = 0 to 7) 0 : Port configured as input 1 : Port configured as output Note : The direction control bits corresponding to P10, P11, P35, P36 and P37 are not used (“0” when read, do not write “1”). Port direction registers are undefined when read (write only). Fig. 8 Structure of port- and port direction registers MITSUBISHI ELECTRIC 9 MITSUBISHI MICROCOMPUTERS 7630 Group SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER (1) Ports P00/AN0 to P07/AN7 (4) Port P13/TX0 Pull-up control bit Pull-up control bit Analog input selection direction register Direction register Data bus Port latch Port latch Data bus ADC input Analog input selection Timer bi-phase mode input (5) Ports P14/CNTR0, P15/CNTR1 Pull-up control bit (2) Port P11/INT0 Direction register Interrupt input Port latch Data bus Data bus Timer bi-phase mode input (3) Port P12/INT1 (6) Port P16/PWM Pull-up control bit Pull-up control bit PWM output enable Direction register Data bus Port latch Direction register Data bus Interrupt input Fig. 9 10 Port latch PWM output Structure of port I/Os (1) MITSUBISHI ELECTRIC MITSUBISHI MICROCOMPUTERS 7630 Group SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER (7) Ports P17, P30, P33, P34 (12) Ports P24/URXD, P27/UCTS Transmission or reception* in Pull-up control bit progress Transmit or receive* enable bit Direction register Pull-up control bit Direction register Port latch Data bus Port latch Data bus URXD or UCTS input (8) Port P20/SIN (13) Ports P25/UTXD, P26/URTS Transmission or reception** in progress Pull-up control bit SIO Port Select Direction register Port latch Data bus Port latch Data bus Pull-up control bit Transmit or receive** enable bit Direction register UTXD or URTS output SIO1 input (*) for UCTS (**) for URTS (14) Port P31/CTX (9) Port P21/SOUT Pull-up control bit Pull-up control bit SIO port selection bit Transmit complete signal Direction register CAN port selection bit Direction register Port latch Data bus Port latch Data bus CTX output SIO output (15) Port P32/CRX CAN dominant level control bit Pull-up/down control bit (10) Port P22/SCLK Direction register Pull-up control bit Clock selection bit Port selection bit direction register Data bus Port latch Port latch Data bus CAN interrupt SIO clock output External clock input CRX input (16) Ports P40/KW0 to P47/KW7 Key-on wake-up control bit Pull-up/down control bit (11) Port P23/SRDY Pull-up control bit Direction register SRDY output selection bit Direction register Data bus Data bus Port latch Port latch Key-on wake-up interrupt SRDY output Fig. 10 Structure of port I/Os (2) MITSUBISHI ELECTRIC 11 MITSUBISHI MICROCOMPUTERS 7630 Group SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER Port Pull-up/pull-down Function Each pin of ports P0 to P4 except P11 is equipped with a programmable pull-up transistor. P32/CRX and P40/KW0 to P47/KW7 are equipped with programmable pull-down transistors as well. The pull-up function of P0 to P3 can be controlled by the corresponding 7 port pull-up control registers (see Structure of port pull-up/down control registers). The pull-up/down function of ports P3 2 and P4 can be controlled by the corresponding port pull-up/pull-down registers together with the polarity control register (see Structure of polarity control register). 0 Port Pi pull-up control register (address 002816 + i) (i = 0, 2) PUP0, PUP2 Pij pull-up transistor control bit (j = 0 to 7) 0 : Pull-up transistor disabled 1 : Pull-up transistor enabled 7 0 Port P1 pull-up control register (address 002916) PUP1 Not used (“0” when read, do not write “1”) P1j pull-up transistor control bit (j = 2 to 7) 7 0 Port P3 pull-up control register (address 002B16) PUP3 P3j pull-up transistor control bit (j = 0, 1) P32 pull-up/down transistor control bit P3j pull-up transistor control bit (j = 3, 4) Not used (“0” when read, do not write “1”) 7 0 Port P4 pull-up/down control register (address 002C16) PUP4 P4j pull-up/down transistor control bit (j = 0 to 7) 0 : Pull-up/down transistor disabled 1 : Pull-up/down transistor enabled Fig. 11 Structure of port pull-up/down control registers 7 0 Polarity control register (address 002F16) PCON Key-on wake-up polarity control bit 0 : Low level active 1 : High level active CAN module dominant level control bit 0 : Low level dominant 1 : High level dominant Not used (undefined when read) Fig. 12 12 Structure of polarity control register MITSUBISHI ELECTRIC MITSUBISHI MICROCOMPUTERS 7630 Group SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER Port Overvoltage Application When configured as input ports, P1 to P4 may be subjected to overvoltage (VI > VCC) if the input current to the applicable port is limited to the specified values (see “Table 8:”). Use a serial resistor of appropriate size to limit the input current. To estimate the resistor value, assume the port voltage to be VCC at overvoltage condition. • Avoid to subject ports to overvoltage causing VCC to rise above 5.5 V. • The overvoltage condition causing input current flowing through the internal port protection circuits has a negative effect on the ports noise immunity. Therefore, careful and intense testing of the target system’s noise immunity is required. Refer to the “countermeasures against noise” of the corresponding users manual. • Port P0 must not be subjected to overvoltage conditions. Notes: • Subjecting ports to overvoltage may effect the supply voltage. Assure to keep VCC and VSS within the target limits. MITSUBISHI ELECTRIC 13 MITSUBISHI MICROCOMPUTERS 7630 Group SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER INTERRUPTS There are 24 interrupts: 6 external, 17 internal, and 1 software. Interrupt Control Each interrupt except the BRK instruction interrupt has both an interrupt request bit and an interrupt enable bit, and is controlled by the interrupt disable flag. An interrupt occurs when the corresponding interrupt request and enable bits are “1” and the interrupt disable flag is “0”. Interrupt enable bits can be cleared or set by software. Interrupt request bits can be cleared by software but cannot be set by software. The BRK instruction interrupt and reset cannot be disabled with any flag or bit. The I flag disables all interrupts except the BRK instruction interrupt and reset. If several interrupt requests occur at the same time, the interrupt with the highest priority is accepted first. Interrupt Operation Upon acceptance of an interrupt, the following operations are automatically performed. 1. The processing being executed is stopped. 14 2. 3. 4. The contents of the program counter and processor status register are automatically pushed onto the stack. Concurrently with the push operation, the interrupt jump destination address is read from the vector table into the program counter. The interrupt disable flag is set and the corresponding interrupt request bit is cleared. Notes on use When the active edge of an external interrupt (INT0, INT1, CNTR0, CNTR1, CWKU or KOI) is changed, the corresponding interrupt request bit may also be set. Therefore, take the following sequence. (1) Disable the external interrupt which is selected. (2) Change the active edge in interrupt edge selection register. (in the case of CNTR0: Timer X mode register; in the case of CNTR1: Timer Y mode register) (3) Clear the interrupt request bit to “0”. (4) Enable the external interrupt which is selected. MITSUBISHI ELECTRIC MITSUBISHI MICROCOMPUTERS 7630 Group SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER . Table 3: Interrupt vector addresses and priority Vector Address (Note 1) Interrupt source Priority High Low Interrupt Request Generating Conditions Remarks Reset (Note 2) 1 FFFB16 FFFA16 At Reset Non-maskable Watchdog timer 2 FFF916 FFF816 At Watchdog timer underflow Non-maskable INT0 3 FFF716 FFF616 At detection of either rising or falling edge of INT0 interrupt External Interrupt (active edge selectable) INT1 4 FFF516 FFF416 At detection of either rising or falling edge of INT1 interrupt External Interrupt (active edge selectable) 5 FFF316 FFF216 At CAN module successful transmission of message Valid when CAN module is activated and request transmit CAN successful receive 6 FFF116 FFF016 At CAN module successful reception of message Valid when CAN module is activated CAN overrun 7 FFEF16 FFEE16 If CAN module receives message when receive buffers are full. Valid when CAN module is activated CAN error passive 8 FFED16 FFEC16 When CAN module enters into error passive state Valid when CAN module is active CAN error bus off 9 FFEB16 FFEA16 When CAN module enters into bus off state Valid when CAN module is active CAN wake up 10 FFE916 FFE816 When CAN module wakes up via CAN bus Timer X 11 FFE716 FFE616 At Timer X underflow or overflow Timer Y 12 FFE516 FFE416 At Timer Y underflow Timer 1 13 FFE316 FFE216 At Timer 1 underflow Timer 2 14 FFE116 FFE016 At Timer 2 underflow Timer 3 15 FFDF16 FFDE16 At Timer 3 underflow CNTR0 16 FFDD16 FFDC16 At detection of either rising or falling edge in CNTR0 input External Interrupt (active edge selectable) CNTR1 17 FFDB16 FFDA16 At detection of either rising or falling edge in CNTR1 input External Interrupt (active edge selectable) UART receive 18 FFD916 FFD816 At completion of UART receive Valid when UART is selected UART transmit 19 FFD716 FFD616 At completion of UART transmit Valid when UART is selected UART transmit buffer empty 20 FFD516 FFD416 At UART transmit buffer empty Valid when UART is selected UART receive error 21 FFD316 FFD216 When UART reception error occurs. Valid when UART is selected Serial I/O 22 FFD116 FFD016 At completion of serial I/O data transmit and receive Valid when serial I/O is selected A-D conversion 23 FFCF16 FFCE16 At completion of A-D conversion Key-on wake-up 24 FFCD16 FFCC16 At detection of either rising or falling edge of P4 input External Interrupt (active edge selectable) BRK instruction 25 FFCB16 FFCA16 At BRK instruction execution Non-maskable CAN successful transmit Notes 1: Vector addresses contain interrupt jump destination address 2: Reset function in the same way as an interrupt with the highest priority MITSUBISHI ELECTRIC 15 MITSUBISHI MICROCOMPUTERS 7630 Group SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER Interrupt request bit Interrupt enable bit Interrupt disable flag I BRK instruction Reset Fig. 13 Interrupt request Interrupt control For the external interrupts INT0 and INT1, the active edge causing the interrupt request can be selected by the INT0 and INT1 interrupt edge selection bits of the interrupt polarity selection register (IPOL); please refer to Fig. 14 below. 7 0 Interrupt polarity selection register (Address 002D16) IPOL Not used (returns to “0” when read, do not write “1” in this bit) INT0 interrupt edge selection bit INT1 interrupt edge selection bit Not used (returns to “0” when read, do not write “1” in these bits) 0 : Falling edge active 1 : Rising edge active Fig. 14 16 Structure of interrupt polarity selection register MITSUBISHI ELECTRIC MITSUBISHI MICROCOMPUTERS 7630 Group SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER 7 0 Interrupt request register A (address 000216) IREQA Interrupt control register A (address 000516) ICONA Not used (returns to ”0” when read) External interrupt INT0 enable bit External interrupt INT1 enable bit CAN successful transmission interrupt enable bit CAN successful receive interrupt enable bit CAN overrun interrupt enable bit CAN error passive interrupt enable bit CAN bus off interrupt enable bit 0 7 Not used (returns to ”0” when read) External interrupt INT0 request bit External interrupt INT1 request bit CAN successful transmission interrupt request bit CAN successful receive interrupt request bit CAN overrun interrupt request bit CAN error passive interrupt request bit CAN bus off interrupt request bit 7 0 0 Interrupt control register B (address 000616) ICONB 7 Interrupt request register B (address 000316) IREQB CAN wake–up interrupt enable bit CAN wake up interrupt request bit Timer X interrupt enable bit Timer X interrupt request bit Timer Y interrupt enable bit Timer Y interrupt request bit Timer 1 interrupt enable bit Timer 1 interrupt request bit Timer 2 interrupt enable bit Timer 2 interrupt request bit Timer 3 interrupt enable bit Timer 3 interrupt request bit CNTR0 interrupt enable bit CNTR0 interrupt request bit CNTR1 interrupt enable bit CNTR1 interrupt request bit 7 0 Interrupt request register C (address 000416) IREQC 7 0 UART receive complete (receive buffer full) interrupt request bit UART transmit complete (transmit register empty) interrupt request bit UART transmit buffer empty interrupt request bit UART receive error interrupt request bit Serial I/O interrupt request bit AD conversion complete interrupt request bit Key-on wake-up interrupt request bit Not used (returns to ”0” when read) 0 : No interrupt request 1 : Interrupt requested Fig. 15 Interrupt control register C (address 000716) ICONC UART receive complete (receive buffer full) interrupt enable bit UART transmit complete (transmit register empty) interrupt enable bit UART transmit buffer empty interrupt enable bit UART receive error interrupt enable bit Serial I/O interrupt enable bit AD conversion complete interrupt enable bit Key-on wake-up interrupt enable bit Not used (returns to ”0” when read) 0: 1: Interrupt disabled Interrupt enabled Structure of interrupt request and control registers A, B and C MITSUBISHI ELECTRIC 17 MITSUBISHI MICROCOMPUTERS 7630 Group SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER KEY-ON WAKE-UP “Key-on wake-up” is one way of returning from a power-down state caused by the STP or WIT instruction. Any terminal of port P4 can be used to generate the key-on wake-up interrupt request. The active polarity can be selected by the key-on wake-up polarity con- trol bit of PCON (see Fig. 12). If any pin of port P4 has the selected active level applied, the key-on wake-up interrupt request will be set to “1”. Please refer to Fig. 16. key-on wake-up control bit P4Dj PUP4j port P4j/KWj … key-on wake-up interrupt port P4j I/O circuit j = 0 to 7 Fig. 16 18 Block diagram of key-on wake-up circuit MITSUBISHI ELECTRIC MITSUBISHI MICROCOMPUTERS 7630 Group SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER TIMERS The 7630 group has five timers: two 16-bit timers and three 8-bit timers . All these timers will be described in detail below. φ 16-bit Timers Timers X and Y are 16-bit timers with multiple operating modes. Please refer to Fig. 17. TYM1,0 1/4 1/16 1/64 1/128 “00” TXM5,4 “01” TXM7 “00”, “11” “01” “10” “10” “11” TXL latch (8) TXH latch (8) TXL counter (8) TXH counter (8) TX interrupt request count direction control P13/TX0 down edge detector “00”, “10”, “11” “01” sign generator P14/CNTR0 TXM5, 4 edge detector “0” CNTR0 interrupt request “1” 1/2 1/8 1/32 “00” “01” TXM6 TXM5, 4=“11” TYM7 TYM3, 2 “0x”, “11” TYH latch (8) TYL counter (8) TYH counter (8) TYM5, 4 “10” 1/64 “11” TYL latch (8) TY interrupt request “10” TYM5, 4=“11” rising edge detector falling edge detector P15/CNTR1 TYM5, 4=“01” “0” “1” “11” TYM6 Fig. 17 CNTR1 interrupt request “0x”, “10” TYM5, 4 Block diagram of timers X and Y (φ is internal system clock) Timer X Timer X is a 16-bit timer with a 16-bit reload latch supporting the following operating modes: (1) Timer mode (2) Bi-phase counter mode (3) Event counter mode (4) Pulse width measurement mode These modes can be selected by the timer X mode register (TXM). In the timer- and pulse width measurement mode, the timer’s count source can be selected by the timer X count source selection bits of the timer Y mode register (TYM). Please refer to the Figures below for the TXM and TYM bit assignment. On read or write access to timer X, note that the high-order and loworder bytes must be accessed in the specific order. Write method When writing to the timer X, write the low-order byte first. The data written is stored in a temporary register which is assigned to the same address as TXL. Next, write the high-order byte. When this is finished, the data is placed in the timer X high-order reload latch and the low-order byte is transferred from its temporary register to the timer X low-order reload latch. Depending on the timer X write control bit, the latch contents are reloaded to the timer immediately (write control bit = “0”) or on the next timer underflow (write control bit = “1”). Read method When reading the timer X, read the high-order byte first. This causes the timer X high- and low-order bytes to be transferred to temporary registers being assigned to the same addresses as TXH and TXL. Next, read the low-order byte which is read from the temporary register. This method assures the correct timer value can be read during the timer count operation. Timer X count stop control Regardless of the actual operating mode, timer X can be stopped by setting the timer X count stop bit (bit 7 of the timer X mode register) to “1”. MITSUBISHI ELECTRIC 19 MITSUBISHI MICROCOMPUTERS 7630 Group SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER 7 0 Timer X mode register (address 001E16) TXM Timer X data write control bit 0 : Data is written to latch and timer 1 : Data is written to latch only Not used (“0” when read, do not write “1”) Timer X mode bits b5 b4 0 0: Timer mode 0 1: Bi-phase counter mode 1 0: Event counter mode 1 1: Pulse width measurement mode CNTR0 polarity selection bit 0 : For event counter mode, rising edge active For interrupt request, falling edge active For pulse width measurement mode, measure “H” period 1 : For event counter mode, falling edge active For interrupt request, rising edge active For pulse width measurement mode, measure “L” period Timer X stop control bit 0 : Timer counting 1 : Timer stopped Fig. 18 Structure of Timer X mode register Timer Y Timer Y is a 16 bit timer with a 16-bit reload latch supporting the following operating modes: (1) Timer mode (3) Event counter mode (5) Pulse period measurement mode (6) H/L pulse width measurement mode These modes can be selected by the timer Y mode register (TYM). In the timer, pulse period- and pulse width measurement modes’ the timer’s count source can be selected by the timer Y count source selection bits. Please refer to Fig. 19. On read or write access to timer Y, note that the high-order and loworder bytes must be accessed in a specific order. Write method When writing to timer Y, write the low-order byte first. The data written is stored in a temporary register which is assigned to the same 20 address as TYL. Next, write the high-order byte. When this is finished, the data is placed in the timer Y high-order reload latch and the low-order byte is transferred from its temporary register to the timer Y low-order reload latch. Read method When reading the timer Y, read the high-order byte first. This causes the timer Y high- and low-order bytes to be transferred to temporary registers being assigned to the same addresses as TYH and TYL. Next, read the low-order byte which is read from the temporary register. This method assures the correct timer value can be read during timer count operation. Timer Y count stop control Regardless of the actual operating mode, timer Y can be stopped by setting the timer Y count stop bit (bit 7 of the timer Y mode register) to “1”. MITSUBISHI ELECTRIC MITSUBISHI MICROCOMPUTERS 7630 Group SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER 7 0 Timer Y mode register (address 001F16) TYM Timer X count source selection bits b1 b0 0 0: φ divided by 4 0 1: φ divided by 16 1 0: φ divided by 64 1 1: φ divided by 128 Timer Y count source selection bits b3 b2 0 0: φ divided by 2 0 1: φ divided by 8 1 0: φ divided by 32 1 1: φ divided by 64 Timer Y operation mode bits b5 b4 0 0: Timer mode 0 1: Pulse period measurement mode 1 0: Event counter mode 1 1: H/L pulse width measurement mode CNTR1 polarity selection bit 0 : For event counter mode, rising edge active For interrupt request, falling edge active For pulse period measurement mode, refer to falling edges 1 : For event counter mode, falling edge active For interrupt request, rising edge active For pulse period measurement mode, refer to rising edges Timer Y stop control bit 0 : Timer counting 1 : Timer stopped Fig. 19 Structure of timer Y mode register (φ is internal system clock) Operating Modes The count direction is determined by the edge polarity and level of count source inputs and may change during the count operation. Refer to the table below. (1) Timer mode This mode is available with timer X and timer Y. • Count source The count source for timer X and Y is the output of the corresponding clock divider. The division ratio can be selected by the timer Y mode register. • Operation Both timers X and Y are down counters. On a timer underflow, the corresponding timer interrupt request bit will be set to “1”, the contents of the corresponding timer latches will be reloaded to the counters and counting continues. Table 4: Timer X count direction in Bi-phase counter mode P13/TX0 ↑ Edge ↓ Edge L (2) Bi-phase counter mode (quadruplicate) This mode is available with timer X only. • Count source The count sources are P14/CNTR0 and the P13/TX0 pins. • Operation Timer X will count both rising and falling edges on both input pins (see above). Refer to Timer X bi-phase counter mode operation for the timing chart of the bi-phase counter mode. H L H P14/CNTR0 Count direction L Up H Down L Down H ↑ Edge ↓ Edge Up Down Up Up Down On a timer over- or underflow, the corresponding interrupt request bit will be set to “1” and counting continues. MITSUBISHI ELECTRIC 21 MITSUBISHI MICROCOMPUTERS 7630 Group SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER P13/TX0 input signal P14/CNTR0 input signal TX counter count direction Fig. 20 down up Timer X bi-phase counter mode operation (3) Event counter mode • This mode is available with timer X and timer Y. • Count source The count source for timer X is the input signal to the P14/CNTR0 pin and for timer Y the input signal to P15/CNTR1 pin. • Operation The timer counts down. On a timer underflow, the corresponding timer interrupt request bit will be set to “1”, the contents of the corresponding timer latches will be reloaded to the counters and counting continues. The active edge used for counting can be selected by the polarity selection bit of the corresponding pin P14/CNTR0 or P15/CNTR1. These bits are part of TXM (Structure of Timer X mode register) and TYM (Structure of timer Y mode register (f is internal system clock)) registers. (4) Pulse width measurement mode This mode is available with timer X only. • Count source The count source is the output of timer X clock divider. The division ratio can be selected by the timer Y mode register. • Operation The timer counts down while the input signal level on P14/CNTR0 matches the active polarity selected by the CNTR0 polarity selection bit of TXM (Structure of Timer X mode register). On a timer underflow, the timer X interrupt request bit will be set to “1”, the contents of the timer latches are reloaded to the counters and counting continues. When the input level changes from active polarity (as selected), the CNTR0 interrupt request bit will be set to “1.” The measurement result may be obtained by reading timer X during interrupt service. (5) Pulse period measurement mode This mode is available with timer Y only. • Count source The count source is the output of timer Y clock divider. 22 Operation The active edge of input signal to be measured can be selected by CNTR1 polarity selection bit (Fig. 18). When this bit is set to “0”, the time between two consecutive falling edges of the signal input to P15/CNTR1 pin will be measured, when the polarity bit is set to “1”, the time between two consecutive rising edges will be measured. The timer counts down. On detection of an active edge of input signal, the contents of the TY counters will be transferred to temporary registers assigned to the same addresses as TY. At the same time, the contents of TY latches will be reloaded to the counters and counting continues. The active edge of input signal also causes the CNTR1 interrupt request bit to be set to “1”. The measurement result may be obtained by reading timer Y during interrupt service. (6) H/L pulse width measurement mode This mode is available with timer Y only. • Count source The count source is the output of the timer Y’s clock divider. • Operation This mode measures both the “H” and “L” periods of a signal input to P15/CNTR1 pin continuously. On detection of any edge (rising or falling) of input signal to P15/CNTR1 pin, the contents of timer Y counters are stored to temporary registers which are assigned to the same addresses as timer Y. At the same time, the contents of timer Y latches are reloaded to the counters and counting continues. The detection of an edge causes the CNTR1 interrupt request bit to be set to “1” as well. The result of measurement may be obtained by reading timer Y during interrupt service. This read access will address the temporary registers. On a timer underflow, the timer Y interrupt request bit will be set to “1”, the contents of timer Y latches will be transferred to the counters and counting continues. MITSUBISHI ELECTRIC MITSUBISHI MICROCOMPUTERS 7630 Group SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER TIMER 1, TIMER 2, TIMER 3 Timers 1 to 3 are 8-bit timers with 8-bit reload latches and one common pre-divider. Timer 1 can operate in the timer mode only, φ 1 1/8 1/32 1/128 “00” T123M67 whereas timers 2 and 3 can be used to generate a PWM output signal timing as well. Timers 1 to 3 are down count timers. See Fig. 21. T1 latch (8) “01” T1 counter (8) “10” T1 interrupt “11” T2 latch (8) “1” “0” T2 counter (8) T123M3 “0” “1” T2 interrupt S T123M1 Q R T3 latch (8) “1” “0” T3 counter (8) T123M4 “0” Fig. 21 T3 interrupt S T123M1 P1D6 T123M1 P16/PWM “1” Q R T123M0 S P16 latch T Q Block diagram of timers 1 to 3 (φ is internal system clock) Timer 1 The count source of timer 1 is the output of timer 123 pre-divider. The division ratio of the pre-divider can be selected by the predivider division ratio bits of timer 123 mode register (T123M). Refer to Timer 123 mode register configuration (f is internal system clock). On a timer 1 underflow, the timer 1 interrupt request bit will be set to “1”. Writing to timer 1 initializes the latch and counter. be selected by the timer count source selection bits of timer 123 mode register (T123M). Timers 2 and 3 Writing to timer 2 register affects the reload latch only or both of the reload latch and counter depending on the timer 2 write control bit of T123M. When the timer write control bit is set to “0”, both latch and counter will be initialized simultaneously; when set to “1” only the reload latch will be initialized, on an underflow, the counter will be set to the modified reload value. Writing to timer 3 initializes latch and counter both. The count source of timers 2 and 3 can be either the output of the timer 123 pre-divider or the timer 1 underflow. The count source can Timer 2 or 3 underflow causes the timer 2 or 3 interrupt request bit to be set to “1”. MITSUBISHI ELECTRIC 23 MITSUBISHI MICROCOMPUTERS 7630 Group SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER 7 0 Timer 123 mode register (address 001916) T123M PWM polarity selection bit 0 : Start on “H” level output 1 : Start on “L” level output PWM output enable bit 0 : PWM output disabled 1 : PWM output enabled Timer 2 write control bit 0 : Latch and counter 1 : Latch only Timer 2 count source selection bit 0 : Timer 1 underflow 1 : Pre-divider output Timer 3 count source selection bit 0 : Timer 1 underflow 1 : Pre-divider output Not used (“0” when read, do not write “1”) Pre-divider division ratio bits b7 b6 0 0: φ divided by 1 0 1: φ divided by 8 1 0: φ divided by 32 1 1: φ divided by 128 Fig. 22 Timer 123 mode register configuration (φ is internal system clock) Operating Modes (1) Timer Mode This mode is available with timers 1 to 3. • Count source For timer 1, the count source is the output of the corresponding pre-divider. For timers 2 and 3, the count source can be separately selected to be either the pre-divider output or timer 1 underflow. • Operation The timer counts down. On a timer underflow, the corresponding timer interrupt request bit will be set to “1”, the contents of the corresponding timer latch will be reloaded to the counter and counting continues. 24 (2) PWM Mode This mode is available with timer 2 and 3. • Count source The count source can be separately selected to be either the pre-divider output or timer 1 underflow. • Operation When the PWM-mode is enabled, timer 2 starts counting. As soon as timer 2 underflows, timer 2 stops and timer 3 starts counting. If bit 0 is set, timer 2 determines the low duration and the initial output level is low. Timer 3 determines the high duration. If bit 0 is zero timer 2 determines the high duration and the initial output level is high. In this case timer 3 determines the low duration. Note: Be sure to configure the P16/PWM pin as an output port before using PWM mode. MITSUBISHI ELECTRIC MITSUBISHI MICROCOMPUTERS 7630 Group SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER SERIAL I/Os The serial I/O section of 7630 group consists of one clock synchronous and one asynchronous (UART) interface. Clock Synchronous Serial I/O (SI/O) speeds. Refer to Block diagram of clock synchronous I/O (f is internal system clock). The operation of the clock synchronous serial I/O can be configured by the serial I/O control register SIOCON; refer to Fig. 25. The clock synchronous interface allows full duplex communication based on 8 bit word length. The transfer clock can be selected from an internal or external clock. When an internal clock is selected, a programmable clock divider allows eight different transmission φ SIOCON2, 1, 0 Clock divider P23/SRDY SIOCON6 SIOCON4 Sync. circuit “1” “0” P23 latch P22/SCLK SIOCON3 SIO counter (3) “1” “0” P22 latch P21/SOUT “1” “0” SIO interrupt SIOCON3 “1” SIO shift register (8) “0” P21 latch P20/SIN SIOCON3 “1” “0” P20 latch Fig. 23 Block diagram of clock synchronous I/O (φ is internal system clock) (1) Clock synchronous serial I/O operation Either an internal or external transfer clock can be selected by bit 6 of SIOCON. The internal clock divider can be programmed by bits 0 to 2 of SIOCON. Bit 3 of SIOCON determines whether the double function pins P20 to P22 will act as I/O ports or serve as SIO pins. Bit 4 of SIOCON allows the same selection for pin P23. When an internal transfer clock is selected, transmission can be triggered by writing data to the SI/O shift register (SIO, address 001216). After an 8–bit transmission has been completed, the SOUT pin will change to high impedance and the SIO interrupt request bit will be set to “1”. When an external transfer clock is selected, the SIO interrupt request bit will be set to “1” after 8 cycles but the contents of the SI/O shift register continue to be shifted while the transfer clock is being input. Therefore, the clock needs to be controlled externally; the SOUT pin will not change to high impedance automatically. MITSUBISHI ELECTRIC 25 MITSUBISHI MICROCOMPUTERS 7630 Group SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER synchronous clock transfer clock write signal to SIO receive enable signal SRDY Serial Output SOUT D0 D1 D2 D3 D4 D5 D6 D7 Serial input SIN D0 D1 D2 D3 D4 D5 D6 D7 SIO interrupt request bit = “1” Note: When an internal clock is selected, SOUT pin will change to high impedance after 8 bits of data have been transmitted. Fig. 24 Timing of clock synchronous SI/O function (LSB first selected) 7 0 SIO control register (address 001316) SIOCON Clock divider selection bits b2 b1 b0 0 0 0 0 1 1 1 1 0 0 1 1 0 0 1 1 0: 1: 0: 1: 0: 1: 0: 1: φ divided by 4 φ divided by 8 φ divided by 16 φ divided by 32 φ divided by 64 φ divided by 128 φ divided by 256 φ divided by 512 P20/SIN, P21/SOUT and P22/SCLK function selection bit 0 : I/O port function 1 : SI/O function P23/SRDY function selection bit 0 : I/O port function 1 : SI/O function Transmission order selection bit 0 : LSB first 1 : MSB first Synchronization clock selection bit 0 : use external clock 1 : use internal clock Not used (“0” when read) Fig. 25 Structure of serial I/O control register (φ is internal system clock) Clock Asynchronous Serial I/O (UART) The UART is a full duplex asynchronous transmit/receive unit. The built-in clock divider and baud rate generator enable a broad range of transmission speeds. Please refer to Block diagram of UART. (1) Description The transmit and receive shift registers have a buffer (consisting of high and low order byte) each. Since the shift registers cannot be 26 written to or read from directly, transmit data is written to the transmit buffer and receive data is read from the receive buffer. A transmit or receive operation will be triggered by the transmit enable bit and receive enable bit of the UART control register UCON (see Structure of UART control register). The double function terminals P25/UTXD, P26/URTS and P24/URXD, P27/UCTS will be switched to serve as UART pins automatically. MITSUBISHI ELECTRIC MITSUBISHI MICROCOMPUTERS 7630 Group SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER (2) Baud rate selection UART status register (USTS, Structure of UART status register) The baud rate of transmission and reception is determined by the setting of the prescaler and the contents of the UART baud rate generator register. It is calculated by: where p is the division ratio of The read-only UART status register consists of 7 bits (bit 0 to bit 6) which indicate the operating status of the UART function and various errors. φ b = ----------------------------------16 ⋅ p ⋅ ( n + 1 ) (3) Handshaking signals the prescaler and n is the content of UART baud rate generator register. The prescalers division ration can be selected by the UART mode register (see below). When used as transmitter the UART will recognize the clear-tosend signal via P27/UCTS terminal for handshaking. When used as receiver it will issue a request-to-send signal through P26/URTS pin. UART mode register (UMOD, Structure of UART mode register) Clear-to-send input When used as a transmitter (transmit enable bit set to “1”), the UART starts transmission after recognizing “L” level on P27/UCTS. After started the UART will continue to transmit regardless of the actual level of P27/UCTS or status of the transmit enable bit. The UART mode register allows to select the transmission and reception format with the following options: • word length: 7, 8 or 9 bits • parity: none, odd or even • stop bits: 1 or 2 Request-to-send output The UART controls the P26/URTS output according to the following conditions. Table 5: Output control conditions It allows to select the prescalers division ratio as well. UART baud rate generator (UBRG) P26/URTS Condition Receive enable bit is set to “1” This 8 bit register allows to select the baud rate of the UART (see above). Set this register to the desired value before enabling reception or transmission. “L” Reception completed during receive enable bit set to “1” Start bit (falling edge) detected UART control register (UCON, Structure of UART control register) Receive enable bit is set to “0” before reception started “H” Hardware reset The UART control register consists of four control bits (bit 0 to bit 3) which allow to control reception and transmission. Receive initialization bit is set to “1” data bus UART control register φ UART status register transmit buffer (9) transmit buffer empty flag UMOD2, 1 1 “00” 1/8 “01” 1/32 “10” transmit register empty interrupt request UMOD7, 6 UBRG (8) transmit buffer empty interrupt request bit counter P25/UTXD transmit shift register (9) 1/256 “11” UMOD4,3,2 transmission control circuit transmit register empty flag P27/UCTS reception control circuit UMOD7, 6 bit counter receive shift register (9) P26/URTS receive error interrupt request P24/URXD receive error flags receive buffer (9) receive buffer full interrupt request receive buffer full flag data bus Fig. 26 Block diagram of UART MITSUBISHI ELECTRIC 27 MITSUBISHI MICROCOMPUTERS 7630 Group SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER 7 0 UART mode register UMOD (address 002016) Not used (“0” when read, do not write “1”) clock divider selection bits b2 b1 0 0 : φ divided by 1 0 1 : φ divided by 8 1 0 : φ divided by 32 1 1 : φ divided by 256 Stop bits selection bit 0 : One stop bit 1 : Two stop bits Parity selection bit 0 : Even parity 1 : Odd parity Parity enable bit 0 : Parity disabled 1 : Parity enabled UART word length selection bits b7 b6 0 0 : 7 bits 0 1 : 8 bits 1 0 : 9 bits 1 1 : Not used Fig. 27 Structure of UART mode register 7 0 UART control register UCON (address 002216) Transmit enable bit 0 : Transmit disabled (an ongoing transmission will be finished correctly) 1 : Transmit enabled Receive enable bit 0 : Receive disabled (an ongoing reception will be finished correctly) 1 : Receive enabled Transmission initialization bit 0 : No action 1 : Clear transmit buffer full flag and transmit shifter full flag, set the transmit status register bits and stop transmission Receive initialization bit 0 : No action 1 : Clear receive status flags and the receive enable bit Not used (“0” when read, do not write “1”) Fig. 28 28 Structure of UART control register MITSUBISHI ELECTRIC MITSUBISHI MICROCOMPUTERS 7630 Group SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER 7 0 UART status register (address 002316) USTS Transmit register empty flag 0 : Register full 1 : Register empty Transmit buffer empty flag 0 : Buffer full 1 : Buffer empty Receive buffer full flag 0 : Buffer full 1 : Buffer empty Receive parity error flag 0 : No parity error detected 1 : Parity error detected Receive framing error flag 0 : No framing error detected 1 : Framing error detected Receive overrun flag 0 : No overrun detected 1 : Overrun detected Receive error sum flag 0 : No error detected 1 : Error detected Not used (“0” when read) Note: this register is read only; writing does not affect its contents. Fig. 29 Structure of UART status register MITSUBISHI ELECTRIC 29 MITSUBISHI MICROCOMPUTERS 7630 Group SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER CAN MODULE The CAN (Controller Area Network) interface of the 7630 group complies with the 2.0B specification, enabling reception and transmission of frames with either 11- or 29- bit identifier length. Refer to Fig. 31 for a block diagram of the CAN interface. The programmer’s interface to the CAN module is formed by three status/control registers (Fig. 32, Fig. 33, Fig. 34), two bus timing control registers (Fig. 35 Fig. 36), several registers for acceptance filtering (Fig. 37), the transmit and receive buffer registers (Fig. 38) and one dominant level control bit (Fig. 22). CAN Bus Timing Control Each bit-time consists of four different segments (see Fig. 30): • Synchronization segment (SS), • Propagation time segment (PTS), • Phase buffer segment 1 (PBS1) and • Phase buffer segment 2 (PBS2). Bit-time SS Baud Rate Selection A programmable clock prescaler is used to derive the CAN module’s basic clock from the internal system clock frequency (φ). Bit 0 to bit 3 of the CAN bus timing control register represent the prescaler allowing a division ratio from 1 to 1/16 to be selected. So the CAN module basic clock frequency fCANB can be calculated as follows: φ fCANB = -----------p+1 where p is the value of the prescaler (selectable from 1 to 15). The effective baud rate of the CAN bus communication depends on the CAN bus timing control parameters and will be explained below. PTS PBS1 PBS2 Sample point Fig. 30 Bit time of CAN module The first of these segments is of fixed length (one Time Quantum) and the latter three can be programmed to be 1 to 8 Time Quanta by the CAN bus timing control register 1 and 2 (see Fig. 35 and Fig. 36). The whole bit-time has to consist of minimum 8 and maximum 25 Time Quanta. The duration of one Time Quantum is the cycle time of fCANB. For example, assuming φ = 5 MHz, p = 0, one Time Quantum will be 200 ns long. This allows the maximum transmission rate of 625 kb/s to be reached (assuming 8 Time Quanta per bit-time). data bus polarity control register CAN status/control registers bus timing control register acceptance mask register acceptance code register receive buffer 1 acceptance filter P31/CTX P32/CRX receive buffer 2 protocol controller transmit buffer wake-up logic CAN wake-up data bus Fig. 31 30 Block diagram of CAN module MITSUBISHI ELECTRIC MITSUBISHI MICROCOMPUTERS 7630 Group SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER 7 0 CAN transmit control register (address 003016) CTRM Sleep control bit 0 : CAN module in normal mode 1 : CAN module in sleep mode Reset/configuration control bit 0 : CAN module in normal mode 1 : CAN module in configuration mode (plus reset at write) Port double function control bit 0 : P31/CTX serves as I/O port 1 : P31/CTX serves as CTX output port Transmit request bit 0 : No transmission requested 1 : Transmission requested (write “0” has no effect) Not used (no operation, “0” when read) Transmit buffer control bit 0 : CPU access possible 1 : No CPU access (write “0” has no effect, while CTRM(3) = 1) Not used (no operation, “0” when read) Transmit status bit (read only) 0 : CAN module idle or receiving 1 : CAN module transmitting Fig. 32 Structure of CAN transmit control register MITSUBISHI ELECTRIC 31 MITSUBISHI MICROCOMPUTERS 7630 Group SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER 7 0 CAN receive control register (address 003D16) CREC Receive buffer control bit 0 : Receive buffer empty 1 : Receive buffer full (write “1” has no effect) Receive status bit (read only) 0 : CAN module idle or transmitting 1 : CAN module receiving Not used (do not write “1”, read as “0”) Auto-receive disable bit 0 : Auto-receive enabled 1 : Auto-receive disabled Note: Suppresses reception of self initiated/transmitted frames Not used (do not write “1”, “0” when read) Fig. 33 Structure of CAN receive control register 7 0 CAN transmit abort register (address 003E16) CABORT Transmit Abort control bit 0 : No Transmit Abort Request 1 : Transmit Abort Request (write “1” has no effect, while CTRM(3) = 0) Not used (No operation, “0” when read) Fig. 34 32 Structure of CAN transmit abort register MITSUBISHI ELECTRIC MITSUBISHI MICROCOMPUTERS 7630 Group SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER 7 0 CAN bus timing control register 1 (address 003116) CBTCON1 Prescaler division ratio selection bits b3 b2 b1 b0 0 0 0 0: φ divided by 1 0 0 0 1: φ divided by 2 0 0 1 0: φ divided by 3 … 1 1 1 0: φ divided by 15 1 1 1 1: φ divided by 16 Sampling control bit 0 : One sample per bit 1 : Three sample per bit Propagation time duration control bits b7 b6 b5 0 0 0: One Time Quantum 0 0 1: Two Time Quanta … 1 1 0: Seven Time Quanta 1 1 1 : Eight Time Quanta Fig. 35 Structure of CAN bus timing control register 1 7 0 CAN bus timing control register 2 (address 003216) CBTCON2 Phase buffer segment 1 duration control bits b2 b1 b0 0 0 0: One Time Quantum 0 0 1: Two Time Quanta … 1 1 0: Seven Time Quanta 1 1 1 : Eight Time Quanta Phase buffer segment 2 duration control bits b5 b4 b3 0 0 0: One Time Quantum 0 0 1: Two Time Quanta … 1 1 0: Seven Time Quanta 1 1 1 : Eight Time Quanta Synchronization jump width control bits b7 b6 0 0 1 1 Fig. 36 0: 1: 0: 1: One Time Quantum Two Time Quanta Three Time Quanta Four Time Quanta Structure of CAN bus timing control register 2 MITSUBISHI ELECTRIC 33 MITSUBISHI MICROCOMPUTERS 7630 Group SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER Acceptance code registers: name 7 CAC0 Not used Not used Not used CSID10 address 0 CSID6 003316 Not used Not used 003416 CSID9 CSID8 CSID1 CSID0 CAC2 Not used Not used Not used Not used CEID 17 CEID16 CEID15 CEID14 003516 CEID7 CEID6 003616 CAC1 CSID5 CSID4 CSID3 CSID2 CAC3 CEID13 CEID12 CEID11 CEID10 CEID9 CEID8 CAC4 CEID5 CEID4 CEID3 CEID2 CEID1 CEID0 CSID7 Not used Not used 003716 Select the bit pattern of identifiers which allows to pass acceptance filtering. Acceptance mask registers: 7 CAM0 Not used Not used Not used MSID 10 MSID9 MSID8 CAM1 MSID1 MSID0 CAM2 Not used Not used Not used Not used MEID17 MEID16 MEID15 MEID14 003A16 CAM3 MEID13 MEID12 MEID11 MEID10 MEID9 MEID8 MEID7 MEID6 003B16 CAM4 MEID5 MEID4 MEID3 MEID2 MEID1 MEID0 MSID5 MSID4 MSID3 MSID2 0 MSID6 003816 Not used Not used 003916 MSID7 Not used Not used 003C16 0 : Mask identifier bit (do not care) 1 : Compare identifier bit with acceptance code register bit (Not used: write to “0”) Fig. 37 Structure of CAN mask and code registers name CTB0, CRB0 CTB1, CRB1 CTB2, CRB2 7 Not used Not used Not used SID5 SID4 SID3 0 SID9 SID8 SID7 SID6 000016 SID2 SID1 SID0 RTR/SRR IDE 000116 EID17 EID16 EID15 EID14 000216 Not used Not used Not used Not used CTB3, CRB3 EID13 EID12 EID11 EID10 EID9 EID8 EID7 EID6 000316 CTB4, CRB4 EID5 EID4 EID3 EID2 EID1 EID0 RTR r1 000416 r0 DLC3 DLC2 DLC1 DLC0 000516 CTB5, CRB5 Not used Not used Not used CTB6, CRB6 data byte 0 000616 CTB7, CRB7 data byte 1 000716 CTB8, CRB8 data byte 2 000816 CTB9, CRB9 data byte 3 000916 CTBA, CRBA data byte 4 000A16 CTBB, CRBB data byte 5 000B16 CTBC, CRBC data byte 6 000C16 CTBD, CRBD data byte 7 000D16 Calculate the actual address as follows: TxD buffer address = 004016 + offset RxD buffer address = 005016 +offset (Not used: write to “0”) Fig. 38 Note 1: 34 offset SID10 Structure of CAN transmission and reception buffer registers All CAN related SFRs must not be written in “CAN sleep” mode. MITSUBISHI ELECTRIC MITSUBISHI MICROCOMPUTERS 7630 Group SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER A-D CONVERTER The A-D converter uses the successive approximation method with 8 bit resolution. The functional blocks of the A-D converter are described below. Refer to Block diagram of A-D converter. Comparison Voltage Generator Channel Selector The channel selector selects one of ports P00/AN0 to P07/AN7, and inputs its voltage to the comparator. A-D conversion register AD The comparison voltage generator divides the voltage between AVSS and VREF by 256, and outputs the divided voltage. The A-D conversion register is a read-only register that stores the result of an A-D conversion. This register must not be read during an A-D conversion. Data bus b7 b0 A-D control register 3 A-D control circuit A-D interrupt request channel selector P00/AN0 A-D conversion register Comparator comparison voltage generator P07/AN7 VREF/Input switch bit VREF Fig. 39 AVSS Block diagram of A-D converter A-D control register (Structure of A-D control register) The A-D control register controls the A-D conversion process. Bits 0 to 2 select a specific analog input pin. Bit 3 signals the completion of an A-D conversion. The value of this bit remains “0” during an A- D conversion, and changes to “1” when an A-D conversion ends. Writing “0” to this bit starts the A-D conversion. Bit 4 is the VREF/ Input switch bit. MITSUBISHI ELECTRIC 35 MITSUBISHI MICROCOMPUTERS 7630 Group SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER 7 0 A-D control register (address 001516) ADCON Analog input pin selection bits b2 b1 b0 000 001 010 011 100 101 110 111 : : : : : : : : P00/AN0 P01/AN1 P02/AN2 P03/AN3 P04/AN4 P05/AN5 P06/AN6 P07/AN7 A-D conversion completion bit 0 : Conversion in progress 1 : Conversion completed VREF/Input switch bit 0 : Off 1 : On Not used (“0” when read, do not write “1”) Fig. 40 Structure of A-D control register A-D Converter Operation The comparator and control circuit reference an analog input voltage with the reference voltage, then stores the result in the A-D conversion register. When an A-D conversion is complete, the control circuit sets the A-D conversion completion bit and the A-D inter- 36 rupt request bit to “1”. The result of A-D conversion can be obtained from the A-D conversion register, AD (address 001416). Note that the comparator is linked to a capacitor, so set f(XIN) to 500 kHz or higher during A-D conversion. MITSUBISHI ELECTRIC MITSUBISHI MICROCOMPUTERS 7630 Group SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER WATCHDOG TIMER The watchdog timer consists of two separate counters: one 7-bit counter (WDH) and one 4-bit counter (WDL). Cascading both counters or using the high-order counter allows only to select the time-out from either 524288 or 32768 cycles of the internal clock φ. Refer to Fig. 41 and Fig. 42. Both counters are addressed by the same watchdog timer register (WDT). When writing to this register, both counters will be set to the following default values: • the high-order counter will be set to address 7F16 • the low-order counter will be set to address F16 regardless of the data written to the WDT register. Reading the watchdog timer register will return the corresponding control bit status, not the counter contents. φ Once the WDT register is written to, the watchdog timer starts counting down and the watchdog timer interrupt is enabled. Once it is running, the watchdog timer cannot be disabled or stopped except by reset. On a watchdog timer underflow, a non-maskable watchdog timer interrupt will be requested. To prevent the system being stopped by STP instruction, this instruction can be disabled by the STP instruction disable bit of WDT register. Once the STP instruction is disabled, it cannot be enabled again except by RESET. “1” 1/256 WDL counter (4) “0” WDT7 “F16” WDH counter (7) WDT interrupt “7F16” WDT register (8) Fig. 41 Block diagram of watchdog timer 7 0 Watchdog timer register (address 002E16) WDT Not used (undefined when read) Stop instruction disable bit 0 : Stop instruction enabled 1 : Execute two NOP instructions instead (once this bit is set to “1” it can not be cleared to “0” again, except on RESET.) Upper byte count source selection bit 0 : Underflow of the low order counter 1 : φ divided by 256 Fig. 42 Structure of watchdog timer register (φ is internal clock system) MITSUBISHI ELECTRIC 37 MITSUBISHI MICROCOMPUTERS 7630 Group SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER RESET CIRCUIT in the recommended operating condition and then returned to “H” level. Refer to Fig. 43 for an example of the reset circuit. The 7630 group is reset according to the sequence shown in Fig. 44. It starts program execution from the address formed by the contents of the addresses FFFB16 and FFFA16, when the RESET pin is held at “L” level for more than 2 µs while the power supply voltage is power on 4.0V power source voltage 0V reset input voltage 0.8V 0V VCC 1 5 M51953AL 4 RESET 0.1µF 3 VSS 7630 group Fig. 43 Example of reset circuit XIN RESET internal reset Address ? Data ? 8192 cycles of XIN (T1, T2) Fig. 44 38 ? 28 to 34 cycles of XIN ? ? ? ? ? ? 24 cycles of XIN Reset sequence MITSUBISHI ELECTRIC FFFA16 ? FFFB16 ADL ADL, ADH ADH 20 cycles of XIN … 1st op code MITSUBISHI MICROCOMPUTERS 7630 Group SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER Register Address Register contents Register Address Register contents CPU mode reg. 000016 4816 Timer XH 001B16 FF16 Interrupt request reg. A 000216 0016 Timer YL 001C16 FF16 Interrupt request reg. B 000316 0016 Timer YH 001D16 FF16 Interrupt request reg. C 000416 0016 Timer X mode reg. 001E16 0016 Interrupt control reg. A 000516 0016 Timer Y mode reg. 001F16 0016 Interrupt control reg. B 000616 0016 UART mode reg. 002016 0010 Interrupt control reg. C 000716 0016 UART control reg. 002216 0016 Port P0 reg. 000816 0016 UART status reg. 002316 0710 Port P0 direction reg. 000916 0016 Port P0 pull-up control reg. 002816 0016 Port P1 reg. 000A16 0016 Port P1 pull-up control reg. 002916 0016 Port P1 direction reg. 000B16 0016 Port P2 pull-up control reg. 002A16 0016 Port P2 reg. 000C16 0016 Port P3 pull-up control reg. 002B16 0016 Port P2 direction reg. 000D16 0016 Port P4 pull-up/down control reg. 002C16 0016 Port P3 reg. 000E16 0016 Interrupt polarity selection reg. 002D16 0016 Port P3 direction reg. 000F16 0016 Watchdog timer reg. 002E16 3F16 Port P4 reg. 001016 0016 Polarity control reg. 002F16 0016 Port P4 direction reg. 001116 0016 CAN transmit control reg. 003016 0216 Serial I/O control reg. 001316 0016 CAN bus timing control reg. 1 003116 0016 A-D control reg. 001516 0816 CAN bus timing control reg. 2 003216 0016 Timer 1 001616 FF16 CAN receive control reg. 003D16 0016 Timer 2 001716 0116 CAN transmit abort reg. 003E16 0016 Timer 3 001816 FF16 Processor status reg. (PS) Timer 123 mode reg. 001916 4016 Program counter (high-order byte) (PCH) contents of FFFB16 Timer XL 001A16 FF16 Program counter (low-order byte) (PCL) contents of FFFA16 0416 Note: The contents of RAM and registers other than the above registers are undefined after reset; thus software initialization is required. Fig. 45 Internal status of microcomputer after reset MITSUBISHI ELECTRIC 39 MITSUBISHI MICROCOMPUTERS 7630 Group SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER CLOCK GENERATING CIRCUIT The 7630 group is equipped with an internal clock generating circuit. Please refer to Fig. 46 for a circuit example using a ceramic resonator or quartz crystal oscillator. For the capacitor values, refer to the manufacturers recommended parameters which depend on each oscillators characteristics. When using an external clock, input it to the XIN pin and leave XOUT open. XIN XOUT CIN Fig. 46 Oscillation Control COUT Ceramic resonator circuit . clock oscillation becomes stable. When using reset, a fixed time-out will be generated allowing oscillation to stabilize. Wait mode The microcomputer enters the wait mode by executing the WIT instruction. The internal clock ø stops at “H” level while the oscillator keeps running. Recovery from wait mode can be done in the same way as from stop mode. However, the time-out period mentioned above is not required to return from wait-mode, thus no such time-out mechanism has been implemented. Note: Set the interrupt enable bit of the interrupt source to be used to return from stop or wait mode to “1” before executing STP or WIT instruction. The 7630 group has two low power modes: the stop and the wait mode. Stop mode The microcomputer enters the stop mode by executing the STP instruction. The oscillator stops with the internal clock φ at “H” level. Timers 1 and 2 will be cascaded and initialized by their reload latches contents. The count source for timer 1 will be set to f(XIN)/16. Oscillation is restarted if an external interrupt is accepted or at reset. When using an external interrupt, the internal clock φ remains at “H” level until timer 2 underflows allowing a time-out until the XOUT 1/4 “1” XIN “0” 1/2 CPUM6 R interrupt request interrupt disable flag S RESET STP delay Q STP Q D S Q φ internal clock for peripherals φ internal clock for CPU T R 2 R STP oscillator countdown (timer 1 and 2) Fig. 47 40 D S R WIT Q T Q S Block diagram of clock generating circuit MITSUBISHI ELECTRIC P2 Q MITSUBISHI MICROCOMPUTERS 7630 Group SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER DATA REQUIRED FOR MASK ORDERS The following are necessary when ordering a mask ROM production: 1 Mask ROM Order Confirmation Form 2 Mark Specification Form 3 Contents of Mask ROM, in EPROM form (three identical copies) The PROM of the blank One Time PROM version is not tested or screened in the assembly process and following processes. To ensure proper operation after programming, the procedure shown in Fig. 48 is recommended to verify programming. Programming with PROM programmer PROM PROGRAMMING METHOD The built-in PROM of the blank One Time PROM version and builtin EPROM version can be read or programmed with a general purpose PROM programmer using a special programming adapter. Set the address of PROM programmer to the user ROM area. Screening *(Note) (150 °C for 40 hours) For the programming adapter type name, please refer to the following table: Verification with PROM programmer Table 6: Programming adapter name MCU type Package Programming adapter type One Time PROM 44P6N-A PCA7430 EPROM 80D0 PCA7431 Functional test in target unit Note on screening: The screening temperature is far higher than the storage temperature. Never subject the device to 150 °C exceeding 100 hours. Fig. 48 Programming and testing of One Time PROM version MITSUBISHI ELECTRIC 41 MITSUBISHI MICROCOMPUTERS 7630 Group SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER Table 7: ABSOLUTE MAXIMUM RATINGS Symbol VCC Parameter Power source voltage Input voltage VI Output voltage VO Ratings Unit –0.3 to 7.0 V –0.3 to VCC + 0.3 V –0.3 to VCC + 0.3 V 500 mW Conditions P00—P07, P11—P17, P20—P27, P30—P34, P40—P47, RESET, XIN P00—P07, P12—P17, P20—P27, P30—P34, P40—P47, XOUT All voltages with respect to VSS and output transistors are “off”. Ta = 25 °C Pd Power dissipation Topr Operating temperature –40 to 85 °C Tstg Storage temperature –60 to 150 °C Table 8: RECOMMENDED OPERATING CONDITIONS (VCC = 4.0 to 5.5 V, VSS = AVSS = 0 V, Ta = – 40 to 85 °C unless otherwise noted) Limits Symbol VCC VSS Parameter Unit Power source voltage min. typ. max. 4.0 5.0 5.5 0 V V VIH “H” Input voltage P00—P07, P11—P17, P20—P27, P30—P34, P40—P47, RESET, XIN 0.8 · VCC VCC V VIL “L” Input voltage P00—P07, P11—P17, P20—P27, P30—P34, P40—P47, RESET, XIN 0 0.2 · VCC V ∑ IOH (peak) “H” sum peak output current P00—P07, P12—P17, P20—P27, P30—P34, P40—P47 –80 mA ∑ IOH (avg) ∑ IOL (peak) ∑ IOL (avg) “H” sum average output current –40 mA “L” sum peak output current 80 mA “L” sum average output current 40 mA IOH (peak) “H” peak output current –10 mA IOH (avg) “H” average output current –5 mA IOL (peak) “L” peak output current 10 mA IOL (avg) “L” average output current 5 mA IIO input current at overvoltage condiP11—P17, P20—P27, tion P30—P34, P40—P47 (VI > VCC) 1 mA ∑ IIO total input current at overvoltage condition (VI > VCC) 16 mA P14/CNTR0, P15/CNTR1 (except bi-phase counter mode) f(XIN)/16 MHz P13/TX0, P14/CNTR0 (bi-phase counter mode) f(XIN)/32 MHz 10 MHz f(CNTR) f(XIN) 42 Timer input frequency (based on 50 % duty) P11—P17, P20—P27, P30—P34, P40—P47 Clock input oscillation frequency MITSUBISHI ELECTRIC MITSUBISHI MICROCOMPUTERS 7630 Group SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER Table 9: ELECTRICAL CHARACTERISTICS (VCC = 4.0 to 5.5 V, VSS = AVSS = 0 V, Ta = – 40 to 85 °C unless otherwise noted) Limits Symbol Parameter Test conditions Unit min. VOH “H” output voltage P00—P07, P12—P17, P20—P27, P30—P34, P40—P47 IOH = –5 mA VOL “L” output voltage P00—P07, P12—P17, P20—P27, P30—P34, P40—P47 IOL = 5 mA VT+ – VT– Hysteresis P11/INT0, P12/INT1, P13/TX0, P14/CNTR0, P15/CNTR1,P20/SIN, P22/SCLK, P26/URTS, P27/UCTS, P32/CRX, RESET IIH “H” input current P00—P07, P11—P17, P20—P27, P30—P34, P40—P47, RESET VI = VCC IIH “H” input current XIN VI = VCC IIL “L” input current P00—P07, P11—P17, P20—P27, P30—P34, P40—P47, RESET VI = VSS IIL “L” input current XIN VI = VSS “H” input current P32, P40—P47 VI = VCC Pull-Down = ’On’ P00—P07, P11—P17, P20—P27, P30—P34, P40—P47, RESET VI = VSS Pull-Up = ’On’ IIH IIL VRAM “L” input current RAM hold voltage typ. max. 0.8 · VCC V 2.0 0.5 When clock stopped MITSUBISHI ELECTRIC V V 5 µA µA 4 –5 µA µA –4 20 200 µA -200 -20 µA 2.0 V 43 MITSUBISHI MICROCOMPUTERS 7630 Group SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER Limits Symbol Parameter Test conditions Unit min. ICC Power source current typ. max. high speed mode, f(XIN) = 8MHz, VCC = 5V, output transistors off, CAN module running, ADC running 11.0 18.0 mA high speed mode, f(XIN) = 8MHz, VCC = 5V, output transistors off, CAN module stopped, ADC running 9.0 16.0 mA middle speed mode, f(XIN) = 8MHz, VCC = 5V, output transistors off, CAN module running, ADC running 6.0 11.0 mA middle speed mode, wait mode, f(XIN) = 8MHz, VCC = 5V, output transistors off, CAN module stopped, ADC stopped 2.0 stop mode, f(XIN) = 0MHz, VCC = 5V, Ta = 25°C 0.1 stop mode, f(XIN) = 0MHz, VCC = 5V, Ta = 85°C Table 10: A-D converter characteristics (VCC = 4.0 to 5.5 V, VSS = AVSS = 0 V, Ta = –40 to 85 °C, mA 1.0 µA 10.0 µA unless otherwise noted) Limits Symbol Parameter Test conditions Unit min. — Resolution — Absolute accuracy tCONV Conversion time VREF Reference input voltage IREF Reference input current RLADDER Ladder resistor value IIAN 44 Analog input current typ. max. 8 Bit ±1.0 ±2.5 LSB 108 tC(XIN) tC(XIN) high–speed mode 106 middle–speed mode 424 432 2.0 VCC V 200 µA VCC = VREF = 5.12 V 150 35 VI = VSS to VCC MITSUBISHI ELECTRIC 0.5 kΩ 5.0 µA MITSUBISHI MICROCOMPUTERS 7630 Group SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER (VCC=4.0 to 5.5 V, VSS=AVSS=0 V, Ta=–40 to 85 °C unless otherwise noted) Table 11: Timing requirements Limits Symbol Parameter Unit min. typ. max. 2 µs External clock input cycle time 100 ns tWH(XIN) External clock input “H” pulse width 37 ns tWL(XIN) External clock input “L” pulse width 37 ns CNTR0, CNTR1 input cycle time (except bi-phase counter mode) 1600 ns CNTR0 input cycle time (bi-phase counter mode) 2000 ns CNTR0, CNTR1 input “H” pulse width (except bi-phase counter mode) 800 ns CNTR0 input “H” pulse width (bi-phase counter mode) 1000 ns CNTR0, CNTR1 input “L” pulse width (except bi-phase counter mode) 800 ns CNTR0 input “L” pulse width (bi-phase counter mode) 1000 ns tL(CNTR0-TX0) Lag of CNTR0 and TX0 input edges (bi-phase counter mode) 500 ns tC(TX0) TX0 input cycle time (bi-phase counter mode) 3200 ns tWH(TX0) TX0 input “H” pulse width (bi-phase counter mode) 1600 ns tWL(TX0) TX0 input “L” pulse width (bi-phase counter mode) 1600 ns tWH(INT) INT0, INT1 input “H” pulse width 460 ns tWL(INT) INT0, INT1 input “L” pulse width 460 ns tC(SCLK) Serial I/O clock input cycle time 8 · tC(XIN) ns tWH(SCLK) Serial I/O clock input “H” pulse width 4 · tC(XIN) ns tWL(SCLK) Serial I/O clock input “L” pulse width 4 · tC(XIN) ns tSU(SIN–SCLK) Serial I/O input setup time 200 ns tH(SCLK–SIN) Serial I/O input hold time 150 ns tW(RESET) Reset input “L” pulse width tC(XIN) tC(CNTR) tWH(CNTR) tWL(CNTR) MITSUBISHI ELECTRIC 45 MITSUBISHI MICROCOMPUTERS 7630 Group SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER Table 12: Switching characteristics (VCC = 4.0 to 5.5 V, VSS = AVSS = 0 V, Ta = –40 to 85 °C, unless otherwise noted) Limits Symbol Parameter Unit min. typ. max. tWH(SCLK) Serial I/O clock output “H” pulse width 0.5 · tC(SCLK) – 50 ns tWL(SCLK) Serial I/O clock output “L” pulse width 0.5 · tC(SCLK) – 50 ns tD(SCLK–SOUT) Serial I/O output delay time tV(SCLK–SOUT) Serial I/O output valid time tR(SCLK) Serial I/O clock output rise time tR(CMOS) CMOS output rise time tF(CMOS) CMOS output fall time 100 pF CMOS output 46 ns 50 ns 50 ns 10 50 ns 10 50 ns 0 measurement output pin Fig. 49 50 Circuit for measuring output switching characteristics MITSUBISHI ELECTRIC MITSUBISHI MICROCOMPUTERS 7630 Group SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER TIMING DIAGRAM tC(TX0) tWH(TX0) tWL(TX0) 0.8·VCC TX0 0.2·VCC tC(CNTR) tWH(CNTR) tWL(CNTR) 0.8·VCC CNTR0, CNTR1 0.2·VCC tWH(INT) tWL(INT) 0.8·VCC INT0, INT1 0.2·VCC tWL(RESET) RESET 0.2·VCC tC(XIN) tWH(XIN) tWL(XIN) 0.8·VCC XIN 0.2·VCC tC(SCLK) tF SCLK tWL(SCLK) tR 0.8·VCC 0.2·VCC tSU(SIN-SCLK) SIN tWH(SCLK) tH(SCLK-SIN) 0.8·VCC 0.2·VCC tD(SCLK-SOUT) tV(SCLK-SOUT) SOUT Fig. 50 Timing diagram MITSUBISHI ELECTRIC 47 REVISION 7630 English Data Sheets REVISION DATE Page New 1.1 MODIFICATIONS Old 10. 98 “CAN controller” is replaced by “CAN module” in whole document. 11 11 Schematics (8) and (11) are corrected. 18 18 Replaced: “PUPDj” with “PUP4j” 26 26 Replaced: “UTXD” with “SOUT” Replaced: “URXD” with “SIN” 38 38 Replaced: “FFFBH” with “FFFB16” Replaced: “FFFAH” with “FFFA16” 41 (1.2) 13.01.99 Replaced: “44P6N” with “44P6N-A) 43 43 Values changed:Iih(35, 113) to (20, 200) and Iil(-122, -70) to (-200, -20); typical values are removed. 10 10 Schematic (1) is modified. 35 35 Fig. 39 is modified. Revision Report M37630 E4/M4 1