SLOS412C − APRIL 2003 − REVISED MARCH 2004 D D D D D D D D Operating Voltage . . . ±2 V to ±18 V Low Noise Voltage . . . 0.8 µVrms (TYP) Wide GBW . . . 12 MHz (TYP) Low THD . . . 0.0005% (TYP) Slew Rate . . . 5 V/µs (TYP) Suitable for Applications Such As Audio Preamplifier, Active Filter, Headphone Amplifier, Industrial Measurement Equipment Drop-In Replacement for NJM4580 Pin and Function Compatible With LM833, NE5532, NJM4558/9, and NJM4560/2/5 D, P, OR PW PACKAGE (TOP VIEW) 1OUT 1IN− 1IN+ VCC− 1 8 2 7 3 6 4 5 VCC+ 2OUT 2IN− 2IN+ description/ordering information The RC4580 is a dual operational amplifier that has been designed optimally for audio applications, such as improving tone control. It offers low noise, high gain bandwidth, low harmonic distortion, and high output current, all of which make the device ideally suited for audio electronics, such as audio preamplifiers and active filters, as well as industrial measurement equipment. When high output current is required, the RC4580 also can be used as a headphone amplifier. Due to its wide operating supply voltage, the RC4580 also can be used in low-voltage applications. ORDERING INFORMATION PACKAGE† TA PDIP (P) −40°C −40 C to 85 85°C C SOIC (D) TSSOP (PW) ORDERABLE PART NUMBER Tube of 50 RC4580IP Tube of 75 RC4580ID Reel of 2500 RC4580IDR Tube of 150 RC4580IPW Reel of 2000 RC4580IPWR TOP-SIDE MARKING RC4580IP R4580I R4580I † Package drawings, standard packing quantities, thermal data, symbolization, and PCB design guidelines are available at www.ti.com/sc/package. Please be aware that an important notice concerning availability, standard warranty, and use in critical applications of Texas Instruments semiconductor products and disclaimers thereto appears at the end of this data sheet. Copyright 2004, Texas Instruments Incorporated !" #$ # % & ## '($ # ) # "( "# ) "" $ POST OFFICE BOX 655303 • DALLAS, TEXAS 75265 1 SLOS412C − APRIL 2003 − REVISED MARCH 2004 equivalent schematic VCC+ Output − Input + Input VCC− 2 POST OFFICE BOX 655303 • DALLAS, TEXAS 75265 SLOS412C − APRIL 2003 − REVISED MARCH 2004 absolute maximum ratings over operating free-air temperature range (unless otherwise noted)† Supply voltage, VCC+ . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ±18 V Input voltage (any input) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ±15 V Differential input voltage, VID . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ±30 V Output current . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ±50 mA Package thermal impedance, θJA (see Notes 1 and 2): D package . . . . . . . . . . . . . . . . . . . . . . . . . . . . 97°C/W P package . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 85°C/W PW package . . . . . . . . . . . . . . . . . . . . . . . . . . 149°C/W Operating virtual junction temperature, TJ . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 150°C Storage temperature range, Tstg . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . −60°C to 125°C † Stresses beyond those listed under “absolute maximum ratings” may cause permanent damage to the device. These are stress ratings only, and functional operation of the device at these or any other conditions beyond those indicated under “recommended operating conditions” is not implied. Exposure to absolute-maximum-rated conditions for extended periods may affect device reliability. NOTES: 1. Maximum power dissipation is a function of TJ(max), θJA, and TA. The maximum allowable power dissipation at any allowable ambient temperature is PD = (TJ(max) − TA)/θJA. Operating at the absolute maximum TJ of 150°C can affect reliability. 2. The package thermal impedance is calculated in accordance with JESD 51-7. recommended operating conditions VCC+ VCC− VICR TA Supply voltage Input common-mode voltage range Operating free-air temperature range MIN MAX 2 16 UNIT −2 −16 −13.5 13.5 V −40 85 °C TYP MAX V electrical characteristics, VCC± = ±15 V, TA = 25°C (unless otherwise noted) PARAMETER TEST CONDITIONS MIN RS ≤ 10 kΩ VIO IIO Input offset voltage IIB AVD Input bias current Large-signal differential-voltage amplification RL ≥ 2 kΩ, VO = ±10 V VOM VICR Output voltage swing RL ≥ 2 kΩ CMRR kSVR‡ Common-mode rejection ratio RS ≤ 10 kΩ Supply-voltage rejection ratio RS ≤ 10 kΩ Input offset current Common-mode input voltage range UNIT 0.5 3 mV 5 200 nA 100 500 nA 90 110 dB ±12 ±13.5 V ±12 ±13.5 V 80 110 dB 80 110 dB ICC Supply current (all amplifiers) ‡ Measured with VCC± varied simultaneously 6 9 mA operating characteristics, VCC± = ±15 V, TA = 25°C (unless otherwise noted) PARAMETER TEST CONDITIONS TYP UNIT SR Slew rate at unity gain RL ≥ 2 kΩ 5 V/µs GBW Gain-bandwidth product f = 10 kHz 12 MHz THD Total harmonic distortion Vn Equivalent input noise voltage VO = 5 V, RL = 2 kΩ, f = 1 kHz, AVD = 20 dB RIAA, RS ≤ 2.2 kΩ, 30-kHz LPF POST OFFICE BOX 655303 • DALLAS, TEXAS 75265 0.0005% 0.8 µVrms 3 SLOS412C − APRIL 2003 − REVISED MARCH 2004 TYPICAL CHARACTERISTICS MAXIMUM OUTPUT VOLTAGE SWING vs LOAD RESISTANCE MAXIMUM OUTPUT VOLTAGE SWING vs FREQUENCY 30 Maximum Output Voltage Swing − V Maximum Output Voltage Swing − V 15 VCC± = ±15 V TA = 25°C 10 VOM+ 5 0 −5 VOM− −10 25 20 15 10 5 0 −15 1k 100 10 k V+/V− = ±15 V RL = 2 kΩ TA = 25°C 1 5 10 50 60 70 80 100 200 300 500 700 1M 10M Frequency − kHz RL − Load Resistance − Ω Figure 2 Figure 1 EQUIVALENT INPUT NOISE VOLTAGE vs FREQUENCY Vn − Equivalent Input Noise Voltage − nV/ Hz OUTPUT VOLTAGE SWING vs OUTPUT CURRENT 20 VCC± = ±15 V Output Voltage Swing − V 15 VOM+ 10 5 0 −5 −10 VOM− −15 −20 1 10 100 IO − Output Current − mA 1000 30 VCC± = ±1.5 V RS = 50 Ω AV = 60 dB TA = 25°C 20 10 0 10 1k Frequency − Hz Figure 4 Figure 3 4 100 POST OFFICE BOX 655303 • DALLAS, TEXAS 75265 10 k 100 k SLOS412C − APRIL 2003 − REVISED MARCH 2004 TYPICAL CHARACTERISTICS OPERATING CURRENT vs TEMPERATURE OUTPUT VOLTAGE SWING vs TEMPERATURE 15 18 V O − Output Voltage Swing − V I CC − Operating Current − mA VOM+ VCC± = ±15 V 16 14 12 10 8 6 4 VCC± = 15 V RL = 2 kΩ 10 5 0 −5 −10 VOM− 2 0 −55 −15 −40 0 25 70 85 −55 125 −40 0 25 TA − Ambient Temperature − °C Figure 5 85 105 Figure 6 INPUT OFFSET VOLTAGE vs TEMPERATURE INPUT BIAS CURRENT vs TEMPERATURE 100 400 VCC± = ±15 V VCC± = ±15 V IIB − Input Bias Current − nA VIO − Input Offset Voltage − µV 70 TA − Ambient Temperature − °C 50 0 −50 300 200 100 0 −100 −50 −40 0 25 70 85 TA − Ambient Temperature − °C 125 −40 0 25 70 85 TA − Ambient Temperature − °C Figure 7 Figure 8 POST OFFICE BOX 655303 • DALLAS, TEXAS 75265 5 SLOS412C − APRIL 2003 − REVISED MARCH 2004 TYPICAL CHARACTERISTICS MAXIMUM OUTPUT VOLTAGE SWING vs OPERATING VOLTAGE OPERATING CURRENT vs OPERATING VOLTAGE 7 TA = 25°C TA = 25°C RL = 2 kΩ 15 +VOM 6 10 5 Operating Current − mA 5 0 −5 −10 −VOM 4 3 2 1 −15 −20 ±5 0 ±10 ±15 0 ±0 ±20 VCC+/VCC− − Operating Voltage − V ±4 ±8 ±10 ±12 Figure 9 Figure 10 TOTAL HARMONIC DISTORTION vs OUTPUT VOLTAGE VOLTAGE GAIN, PHASE vs FREQUENCY ±14 VCC± = ±15 V RL = 2 kΩ 40-dB Amplification TA = 25°C 40 35 20 kHz 20 Hz 0.001 30 −90 −120 20 −150 15 −210 5 −240 10 k 100 k 1M Frequency − Hz Figure 12 Figure 11 POST OFFICE BOX 655303 −180 10 0 10 −30 25 1 kHz 1 VO − Output Voltage − V 0 −60 Phase Gain 0.1 ±16 30 45 VCC± = ±15 V Gain = 20 dB RL = 2 kΩ 0.01 0.0001 6 ±6 VCC+/VCC− − Operating Voltage − V Voltage Gain − dB THD − Total Harmonic Distortion − % 0.1 ±2 • DALLAS, TEXAS 75265 −270 10 M Phase − Deg V O − Maximum Output Voltage Swing − V 20 MECHANICAL DATA MPDI001A – JANUARY 1995 – REVISED JUNE 1999 P (R-PDIP-T8) PLASTIC DUAL-IN-LINE 0.400 (10,60) 0.355 (9,02) 8 5 0.260 (6,60) 0.240 (6,10) 1 4 0.070 (1,78) MAX 0.325 (8,26) 0.300 (7,62) 0.020 (0,51) MIN 0.015 (0,38) Gage Plane 0.200 (5,08) MAX Seating Plane 0.010 (0,25) NOM 0.125 (3,18) MIN 0.100 (2,54) 0.021 (0,53) 0.015 (0,38) 0.430 (10,92) MAX 0.010 (0,25) M 4040082/D 05/98 NOTES: A. All linear dimensions are in inches (millimeters). B. This drawing is subject to change without notice. C. Falls within JEDEC MS-001 For the latest package information, go to http://www.ti.com/sc/docs/package/pkg_info.htm POST OFFICE BOX 655303 • DALLAS, TEXAS 75265 MECHANICAL DATA MTSS001C – JANUARY 1995 – REVISED FEBRUARY 1999 PW (R-PDSO-G**) PLASTIC SMALL-OUTLINE PACKAGE 14 PINS SHOWN 0,30 0,19 0,65 14 0,10 M 8 0,15 NOM 4,50 4,30 6,60 6,20 Gage Plane 0,25 1 7 0°– 8° A 0,75 0,50 Seating Plane 0,15 0,05 1,20 MAX PINS ** 0,10 8 14 16 20 24 28 A MAX 3,10 5,10 5,10 6,60 7,90 9,80 A MIN 2,90 4,90 4,90 6,40 7,70 9,60 DIM 4040064/F 01/97 NOTES: A. B. C. D. All linear dimensions are in millimeters. This drawing is subject to change without notice. Body dimensions do not include mold flash or protrusion not to exceed 0,15. Falls within JEDEC MO-153 POST OFFICE BOX 655303 • DALLAS, TEXAS 75265 IMPORTANT NOTICE Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, modifications, enhancements, improvements, and other changes to its products and services at any time and to discontinue any product or service without notice. Customers should obtain the latest relevant information before placing orders and should verify that such information is current and complete. All products are sold subject to TI’s terms and conditions of sale supplied at the time of order acknowledgment. TI warrants performance of its hardware products to the specifications applicable at the time of sale in accordance with TI’s standard warranty. Testing and other quality control techniques are used to the extent TI deems necessary to support this warranty. Except where mandated by government requirements, testing of all parameters of each product is not necessarily performed. TI assumes no liability for applications assistance or customer product design. Customers are responsible for their products and applications using TI components. To minimize the risks associated with customer products and applications, customers should provide adequate design and operating safeguards. TI does not warrant or represent that any license, either express or implied, is granted under any TI patent right, copyright, mask work right, or other TI intellectual property right relating to any combination, machine, or process in which TI products or services are used. Information published by TI regarding third-party products or services does not constitute a license from TI to use such products or services or a warranty or endorsement thereof. Use of such information may require a license from a third party under the patents or other intellectual property of the third party, or a license from TI under the patents or other intellectual property of TI. Reproduction of information in TI data books or data sheets is permissible only if reproduction is without alteration and is accompanied by all associated warranties, conditions, limitations, and notices. Reproduction of this information with alteration is an unfair and deceptive business practice. TI is not responsible or liable for such altered documentation. Resale of TI products or services with statements different from or beyond the parameters stated by TI for that product or service voids all express and any implied warranties for the associated TI product or service and is an unfair and deceptive business practice. TI is not responsible or liable for any such statements. Following are URLs where you can obtain information on other Texas Instruments products and application solutions: Products Applications Amplifiers amplifier.ti.com Audio www.ti.com/audio Data Converters dataconverter.ti.com Automotive www.ti.com/automotive DSP dsp.ti.com Broadband www.ti.com/broadband Interface interface.ti.com Digital Control www.ti.com/digitalcontrol Logic logic.ti.com Military www.ti.com/military Power Mgmt power.ti.com Optical Networking www.ti.com/opticalnetwork Microcontrollers microcontroller.ti.com Security www.ti.com/security Telephony www.ti.com/telephony Video & Imaging www.ti.com/video Wireless www.ti.com/wireless Mailing Address: Texas Instruments Post Office Box 655303 Dallas, Texas 75265 Copyright 2004, Texas Instruments Incorporated