DATA SHEET DI100S~DI1010S SURFACE MOUNT GLASS PASSIVATED SINGLE-PHASE BRIDGE RECTIFIER VOLTAGE 50 to 1000 Volts CURRENT 1.0 Amperes Unit : inch (mm) SDIP .060(1.524) FEATURES .009(0.25) .335(8.51) • Plastic material used carries Underwriters Laboratory recognition 94V-O .040(1.016) Recognized File #E111753 .316(8.05) .011(0.28) .004(0.10) .310(7.9) .290(7.4) .255(6.5) • Ideal for printed circuit board .245(6.2) • Surge overload rating-- 30 amperes peak .360(9.40) .410(10.4) • Low leakage • Exceeds environmental standards of MIL-S-19500/228 • In compliance with EU RoHS 2002/95/EC directives .045(1.14) .035(0.89) MECHANICALDATA .205(5.2) .195(5.0) Polarity: Polarity symbols molded or marking on body .089(2.5) Terminals: Lead solderable per MIL-STD-750, Method 2026 .086(2.2) Case: Reliable low cost construction utilizing molded plastic technique results in inexpensive product Mounting Position: Any Weight: 0.02 ounce, 300mg MAXIMUM RATINGS AND ELECTRICAL CHARACTERISTICS Ratings at 25°C ambient temperature unless otherwise specified.Single phase, half wave, 60Hz, Resistive or inductive load. For capacitive load, derate current by 20% PARAMETER SYMBOL D I100S D I101S D I102S D I104S D I106S D I108S D I1010S UNITS Maxi mum Recurrent Peak Reverse Voltage VRRM 50 100 200 400 600 800 1000 V Maxi mum RMS Bri dge Input Voltage VRMS 35 70 140 280 420 560 700 V Maxi mum D C Blocki ng Voltage VDC 50 100 200 400 600 800 1000 V Maxi mum Average Forward C urrent TA=40OC IAV 1.0 A IFSM 30 A I2t 3.735 A 2t VF 1.1 V Maxi mum D C Reverse C urrent TA=25 C at Rated D C Blocki ng VoltageTA=125 OC IR 5.0 500 uA Typi cal Juncti on capaci tance (Note 1) CJ 25 pF RθJA RθJL 40 15 TJ,TSTG -55 to +150 Peak Forward Surge C urrent : 8.3ms si ngle half si ne-wave superi mposed on rated load (JED EC method) I2t Rati ng for fusi ng ( t<8.35ms) Maxi mum Forward Voltage D rop per Bri dge Element at 1.0A O Typi cal thermal resi stance per leg ((Note 2) Operati ng Junsti on and Storage Temperature Range O C/W O C NOTES: 1. Measured at 1.0 MHz and applied reverse voltage of 4.0 Volts 2. Thermal resistance from junction to ambient and from junction to lead mounted on P.C.B. with 0.5 X 0.5"(13 X 13mm) copper pads STAD-JAN.22.2007 PAGE . 1 3.0 2.5 2.0 1.5 1.0 0.5 0 0 50 100 150 INSTANTANEOUS FWD CURRENT, AMPERES AVERAGE FORWARD OUTPUT CURRENT, AMPERES RATING AND CHARACTERISTIC CURVES T J =25 OC Pulse Width = 200uS AMBIENT TEMPERATURE, O C INSTANTANEOUS FWD VOLTAGE, VOLTS 10 O TA = 100 C 1.0 0.1 O TA= 25 C 0.01 0 20 40 60 80 100 120 140 PERCENT OF PEAK REVERSE VOLTAGE, % FIG.3 TYPICAL REVERSE CHARACTERISTICS STAD-JAN.22.2007 FIG.2 TYPICAL FORWARD CHARACTERISTICS FORWARD SURGE CURRENT, AMPERES pk (HALF SINE-WAVE) INSTANTANEOUS REVERSE CURRENT,uA F I G . 1 D E R AT I N G C U RV E F O R O U T P U T RECTIFIED CURRENT 50 40 30 20 10 0 1 2 6 10 20 40 60 100 NO. OF CYCLES AT 60Hz FIG.4 MAX NON-REPETITIVE SURGE CURRENT PAGE . 2 MOUNTING PAD LAYOUT ORDER INFORMATION • Packing information T/R - 1.5K per 13" plastic Reel LEGAL STATEMENT Copyright PanJit International, Inc 2007 The information presented in this document is believed to be accurate and reliable. The specifications and information herein are subject to change without notice. Pan Jit makes no warranty, representation or guarantee regarding the suitability of its products for any particular purpose. Pan Jit products are not authorized for use in life support devices or systems. Pan Jit does not convey any license under its patent rights or rights of others. STAD-JAN.22.2007 PAGE . 1