RB200 SERIES 2.0 A SILICON BRIDGE RECTIFIERS VOLTAGE 50 to 1000 Volts CURRENT 2.0 Amperes FEATURES • Plastic material used carries Underwriters Laboratory recognition. • High case dielectric strength. • Typical IR LESS Than 1uA. • Exceeds environmental standards of MIL-STD-19500 • Ideal for printed circuit board. • High temperature soldering guaranteed: 265OC/10 seconds/ .375” (9.5 mm) lead length/5 Ibs. (2.3kg) tension • Component are in compliance with EU RoHS 2002/95/EC directives MECHANICALDATA • Case: Reliable low cost construction utilizing molded plastic technique • Terminals: Leads solderable per MIL-STD-750, Method 2026 • Mounting Position: Any • Weight:1.4 grams. MAXIMUM RATINGS AND ELECTRICAL CHARACTERISTICS Rating at 25°C ambient temperature unless otherwise specified. Resistive or inductive load, Single phase, half wave, 60Hz. For Capacitive load derate current by 20%. PARAMETER SYMBOL RB200 RB201 RB202 RB204 RB206 RB208 RB2010 UNITS Maximum Recurrent Peak Reverse Voltage VRRM 50 100 200 400 600 800 1000 V Maximum RMS Bridge Input Voltage VRMS 35 70 140 280 420 560 700 V Maximum DC Blocking Voltage VDC 50 100 200 400 600 800 1000 V Maximum Average Forward Rectified Output Current .375" (9.5mm ) Lead Length at TA=25O C IF(AV) 2.0 A Peak Forward Surge Current : 8.3ms single half sine-wave superimposed on rated load (JEDEC method) IFSM 50 A I2 t Rating for fusing ( t<8.35ms) I 2t 15 A2 s Maximum Forward Voltage Drop per Element at 1.0A VF 1.0 V Maximum DC Reverse Current TA=25 O C at Rated DC Blocking Voltage T A=100 O C IR 10 1 µA Typical Junction capacitance per bridge element (Note 1) CJ 30 pF Operating Junction Temperature Range TJ -55 to + 125 O C TSTG -55 to + 150 O C Storage Temperature Range NOTES: 1. Measured at 1.0 MHz and applied reverse voltage of 4.0 Volts. STAD-JAN.11.2007 PAGE . 1 RB200 SERIES 80 PEAK FORWARD SURGE CURRENT, AMPERES BRIDGE OUTPUT FULL WAVE RECTIFIED CURRENT AVERAGE AMPERES 4.0 3.5 3.0 2.5 2.0 1.5 1.0 0.5 0 0 20 40 60 80 100 120 T A=25 OC 8.3ms SINGLE HALF SINE WAVE JEDED METHOD 60 40 30 20 10 0 2 140 6 10 20 40 60 100 NUMBER OF CYCLES AT 60Hz O AMBIENT TEMPERATURE, C Fig.1 DERATING CURVE OUTPUT RECTIFIED CURRENT Fig.2MAXIMUM NON-REPETITIVE PEAK FORWARD CURRENT 20 10 INSTANTANEOUS REVERSE CURRENT, uA INSTANTANEOUS FORWARD CURRENT, AMPERES 4 10 1.0 0.1 T J =25 OC Pulse Width =300us 1% Duty Cycle 0.01 0.4 0.6 0.8 1.0 1.2 T J=100 OC 1.0 0.1 T J=25 OC 0.01 1 1.4 INSTANTANEOUS FORWARD VOLTAGE, VOLTS 20 40 60 80 100 120 160 PERCENT OF RATED PEAK REVERSE VOLTAGE Fig.4 TYPICAL REVERSE CHARACTERISTICS Fig.3 TYPICAL FORWARD CHARACTERISTIC 100 CAPACITANCE, pF 60 40 20 10 6 4 2 1 .1 .2 .4 1 2 4 10 20 40 100 REVERSE VOLTAGE, VOLTS Fig.5 TYPICAL JUNCTION CAPACITANCE PER BRIDGE ELEMENT STAD-JAN.11.2007 PAGE . 2