SANYO 10SVP10M

OS-CON DATA SHEET
No.OS02N-DFSVP004
OS-CON 10SVP10M
Frequency (kHz)
Impedance (ohm)
ESR (ohm)
0.12
138.134
2.566
0.5
33.802
1.288
1
17.200
0.898
10
1.901
0.346
100
0.295
0.163
500
0.137
0.125
1000
0.123
0.120
5000
0.117
0.116
10000
0.127
0.116
Frequency characteristics
1000
Impedance (ohm)
ESR (ohm)
ESR, Impedance (ohm)
100
10
1
0.1
0.01
0.001
0.1
1
10
100
1000
10000
Frequency (kHz)
Measureing equipment: HP4194A
Test fixture: HP16047C
Measuring position: root of leads
OS Engineering Department, OS-CON Control Department
Saga SANYO Industries Co., Ltd.
n = 3p.(Ave.)
Room temperature
OS-CON DATA SHEET
SVP series
Test item
Endurance
(After V.P.S test)
Test temperature
105 deg. C
Model
Applied voltage
10V
Lot No.
10SVP10M
041902311
Tangent of loss angle (120Hz)
Change in capacitance (120Hz)
Tangent of loss angle
20
Percent delta (%)
10
0
-10
-20
-30
-40
2000
0
Time[h]
ESR (100kHz)
Leakage current (10V 60s)
10000
500
450
400
350
300
250
200
150
100
50
0
1000
100
10
1
0.1
0.01
0
2000
Time[h]
Note:
2000
Time[h]
Leakage current(µA)
ESR(mohm)
0
0.15
0.14
0.13
0.12
0.11
0.1
0.09
0.08
0.07
0.06
0.05
0.04
0.03
0.02
0.01
0
0
2000
Time[h]
n =30p.
V.P.S test conditions : 230deg.C×75s×2times
(V.P.S = Vapor Phase Soldering method)
Start on August 29, 2000
Executed by M. Koyama
End on December 14, 2000
Drawn by M. Kimura
No.OS02D-DESVP004
OS Engineering Department, OS-CON Control Department, Saga SANYO Industries Co., Ltd.
OS-CON DATA SHEET
SVP series
Test item
Damp heat (Steady state)
(After V.P.S test)
Test temperature
60 deg.C
Model
Test humidity
90% RH
Lot No.
10SVP10M
041902311
Change in capacitance (120Hz)
Tangent of loss angle (120Hz)
Tangent of loss angle
20
Percent delta [%]
10
0
-10
-20
-30
-40
1000
0
Time[h]
ESR (100kHz)
Leakage current (10V 60s)
500
450
400
350
300
250
200
150
100
50
0
10000
1000
100
10
1
0.1
0.01
0
1000
Time[h]
Note:
1000
Time[h]
Leakage current(µA)
ESR(mohm)
0
0.15
0.14
0.13
0.12
0.11
0.1
0.09
0.08
0.07
0.06
0.05
0.04
0.03
0.02
0.01
0
0
1000
Time[h]
n =20p.
V.P.S test conditions : 230deg.C×75s×2times
(V.P.S = Vapor Phase Soldering method)
Start on September 4, 2000
Executed by M. Koyama
End on October 17, 2000
Drawn by M. Kimura
No.OS02D-DHSVP004
OS Engineering Department, OS-CON Control Department, Saga SANYO Industries Co., Ltd.