OS-CON DATA SHEET No.OS02N-DFSVP008 OS-CON 20SVP10M Frequency (kHz) Impedance (ohm) ESR (ohm) 0.12 123.900 1.077 0.5 29.993 0.442 1 15.133 0.281 10 1.533 0.096 100 0.177 0.058 500 0.054 0.044 1000 0.045 0.044 5000 0.092 0.068 10000 0.169 0.114 Frequency characteristics 1000 Impedance (ohm) ESR (ohm) ESR, Impedance (ohm) 100 10 1 0.1 0.01 0.001 0.1 1 10 100 1000 10000 Frequency (kHz) Measureing equipment: HP4194A Test fixture: HP16047C Measuring position: root of leads OS Engineering Department, OS-CON Control Department Saga SANYO Industries Co., Ltd. n = 3p.(Ave.) Room temperature OS-CON DATA SHEET SVP series Test item Endurance (After V.P.S test) Test temperature 105 deg.C Model Applied voltage 20V Lot No. 20SVP10M 1N2902821 Tangent of loss angle (120Hz) Change in capacitance (120Hz) Tangent of loss angle 20 Percent delta [%] 10 0 -10 -20 -30 -40 2000 0 Time[h] ESR (100kHz) Leakage current (20V 60s) 10000 200 180 160 140 120 100 80 60 40 20 0 1000 100 10 1 0.1 0.01 0 2000 Time[h] Note: 2000 Time[h] Leakage current(µA) ESR(mohm) 0 0.15 0.14 0.13 0.12 0.11 0.1 0.09 0.08 0.07 0.06 0.05 0.04 0.03 0.02 0.01 0 0 2000 Time[h] n =30p. V.P.S test conditions : 230deg.C×75s×2times (V.P.S=Vapor Phase Soldering method) Start on December 26, 2001 Executed by R. Kawachino End on March 19, 2002 Drawn by S. Yoshino No.OS02D-DESVP008 OS Engineering Departmaent, OS-CON Control Department, Saga SANYO Industries Co., Ltd. OS-CON DATA SHEET SVP series Test item Damp heat (Steady state) (After V.P.S test) Test temperature 60 deg.C Model Test humidity 90% RH Lot No. 20SVP10M 1N2902821 Change in capacitance (120Hz) Tangent of loss angle (120Hz) Tangent of loss angle 20 Percent delta [%] 10 0 -10 -20 -30 -40 1000 1000 Time[h] ESR (100kHz) Leakage current (20V 60s) 200 180 160 140 120 100 80 60 40 20 0 10000 1000 100 10 1 0.1 0.01 0 1000 Time[h] Note: 0 Time[h] Leakage current(µA) ESR(mohm) 0 0.15 0.14 0.13 0.12 0.11 0.1 0.09 0.08 0.07 0.06 0.05 0.04 0.03 0.02 0.01 0 0 1000 Time[h] n =20p. V.P.S test conditions : 230deg.C×75s×2times (V.P.S = Vapor Phase Soldering method) *Voltage Processing: Applying rated voltage for 120 min at 105deg.C. Start on December 26, 2001 Executed by S. Yoshino End on February 6, 2002 Drawn by S. Yoshino No.OS02D-DHSVP008 OS Engineering Department, OS-CON Control Department, Saga SANYO Industries Co., Ltd. *