SANYO OS-CON16SVP330M

OS-CON DATA SHEET
OS-CON 16SVP330M
Frequency (kHz)
Impedance (ohm)
ESR (ohm)
0.12
3.824
0.079
0.5
0.930
0.044
1
0.474
0.037
10
0.058
0.020
100
0.012
0.011
500
0.020
0.010
No.OS02N-DFSVP056
1000
0.040
0.010
5000
0.190
0.014
10000
0.320
0.019
Frequency characteristics
1000
Impedance (ohm)
ESR (ohm)
ESR, Impedance (ohm)
100
10
1
0.1
0.01
0.001
0.1
1
10
100
1000
10000
Frequency (kHz)
Measuring equipment: HP4194A
Test fixture: HP16047C
Measuring position: root of leads
OS Engineering Department, OS-CON Control Department
Saga SANYO Industries Co., Ltd.
n = 3p.(Ave.)
Room temperature
OS-CON DATA SHEET
SVP series
Test item
Endurance
(After V.P.S test)
Test temperature
105 deg.C
Model
Applied voltage
16 V
Lot No.
16SVP330M
060202471
Tangent of loss angle (120Hz)
Change in capacitance (120Hz)
Tangent of loss angle
20
Percent delta [%]
10
0
-10
-20
-30
-40
2000
0
Time[h]
ESR (100kHz)
Leakage current (16V 60s)
10000
100
90
80
70
60
50
40
30
20
10
0
1000
100
10
1
0.1
0.01
0
2000
Time[h]
Note:
2000
Time[h]
Leakage current(µA)
ESR(mohm)
0
0.15
0.14
0.13
0.12
0.11
0.1
0.09
0.08
0.07
0.06
0.05
0.04
0.03
0.02
0.01
0
0
2000
Time[h]
n =30p.
V.P.S test conditions : 230deg.C×75s×2times
(V.P.S = Vapor Phase Soldering method)
Start on June 20, 2000
Executed by M. Koyama
End on September 11, 2000
Drawn by S. Kodera
No.OS02D-DESVP056
OS Engineering Department., OS-CON Control Department, Saga SANYO Industries Co., Ltd.
OS-CON DATA SHEET
SVP series
Test item
Damp heat (Steady state)
(After V.P.S test)
Test temperature
60 deg.C
Model
Test humidity
90% RH
Lot No.
16SVP330M
060202471
Change in capacitance (120Hz)
Tangent of loss angle (120Hz)
Tangent of loss angle
20
Percent delta [%]
10
0
-10
-20
-30
-40
1000
0
Time[h]
ESR (100kHz)
Leakage current (16V 60s)
100
90
80
70
60
50
40
30
20
10
0
10000
1000
100
10
1
0.1
0.01
0
1000
Time[h]
Note:
1000
Time[h]
Leakage current(µA)
ESR(mohm)
0
0.15
0.14
0.13
0.12
0.11
0.1
0.09
0.08
0.07
0.06
0.05
0.04
0.03
0.02
0.01
0
0
1000
Time[h]
n =20p.
V.P.S test conditions : 230deg.C×75s×2times
(V.P.S = Vapor Phase Soldering method)
Start on June 15, 2000
Executed by M. Koyama
End on July 27, 2000
Drawn by M. Kimura
No.OS02D-DHSVP056
OS Engineering Department, OS-CON Control Department, Saga SANYO Industries Co., Ltd.