Ordering number : ENA0333A LB11692JH Monolithic Digital IC 24V Fan Motor Driver IC Overview The LB11692JH is a three-phase brushless motor driver IC that uses a direct PWM drive technique to achieve highly efficient drive. It is optimal for driving fuel pump motors and other miniature motors. Functions • Direct PWM drive • PWM control based on both a DC voltage input (the CTL voltage) and a pulse input • Provides a 5V regulator output • One Hall-effect sensor FG output • Start/stop switching circuit (Stop mode includes a power saving function.) • Built-in integrating amplifier • Automatic recovery constraint protection circuit (on/off = 1/14), RD output • Built-in current limiter circuit • Built-in LVSD circuit • Built-in thermal protection circuit Specifications Absolute Maximum Ratings at Ta = 25°C Parameter Supply voltage range Symbol Conditions VCC max Ratings Unit 30 V T ≤ 500ms 1.8 A Allowable power dissipation 1 Pd max1 Independent IC 0.9 W Allowable power dissipation 2 Pd max2 Mounted on a specifed board* 2.1 W Output current IO max Operating temperature Topr -40 to +85 °C Storage temperature Tstg -55 to +150 °C * Mounted on a specified board: 114.3mm×76.1mm×1.6mm, glass epoxy Any and all SANYO Semiconductor products described or contained herein do not have specifications that can handle applications that require extremely high levels of reliability, such as life-support systems, aircraft's control systems, or other applications whose failure can be reasonably expected to result in serious physical and/or material damage. Consult with your SANYO Semiconductor representative nearest you before using any SANYO Semiconductor products described or contained herein in such applications. SANYO Semiconductor assumes no responsibility for equipment failures that result from using products at values that exceed, even momentarily, rated values (such as maximum ratings, operating condition ranges, or other parameters) listed in products specifications of any and all SANYO Semiconductor products described or contained herein. D1306 MS IM 20060404-S00005 No.A0333-1/12 LB11692JH Allowable Operating Ranges at Ta = 25°C Parameter Symbol Conditions Ratings Unit Supply voltage range VCC 9.5 to 28 V Constant voltage output current IREG 0 to -30 mA RD output current IRD 0 to 10 mA FG output current IFG 0 to 10 mA Electrical Characteristics at Ta = 25°C, VCC = VM = 24V Ratings Parameter Symbol Conditions unit min Current drain 1 ICC1 Current drain 2 ICC2 typ max 13 17 mA When STOP 4.5 6 mA [Output Block] Output saturation voltage 1 VO sat1 IO = 0.7A,VO(SINK)+VO(SOURCE) 1.5 2.05 V Output saturation voltage 2 VO sat2 IO = 1.5A,VO(SINK)+VO(SOURCE) 2.2 2.9 V Output leakage current IO leak 100 µA Low side diode forward voltage 1 VD1-1 ID = -0.7A 1.1 1.35 V Low side diode forward voltage 2 VD1-2 ID = -1.5A 1.4 1.8 V High side diode forward voltage 1 VD2-1 ID = 0.7A 1.25 1.65 V High side diode forward voltage 2 VD2-2 ID = 1.5A 1.9 2.5 V [5V Constant Voltage Output] Output voltage VREG 5.0 5.3 V Line regulation ∆VREG1 VCC = 9.5 to 28V IO = -5mA 30 100 mV Load regulation ∆VREG2 IO = -5 to -20mA 20 100 mV 4.7 [Hall Amplifier] Input bias current IB(HA) Common-mode input voltage range VICM 0 Hall sensor input sensitivity VHIN 80 ∆VIN(HA) 15 Hysteresis -1 µA -0.2 VREG-2.0 V mVp-p 24 42 mV Input voltage (low to high) VSLH 12 mV Input voltage (high to low) VSHL -12 mV [CSD Pin] High-level output voltage VOH(CSD) 2.75 3.0 3.25 V Low-level output voltage VOL(CSD) 0.85 1.0 1.15 V External capacitor charge current ICSD1 -3.3 -2.4 -1.4 µA External capacitor discharge current ICSD2 0.09 0.17 0.23 Charge/discharge current ratio RCSD Charge current/discharge current 14 µA Times [Undervoltage Protection Circuit (LVS Pin)] Operating voltage VSDL 3.55 3.8 4.0 Release voltage VSDH 4.05 4.3 4.5 V Hysteresis ∆VSD 0.35 0.5 0.65 V 0.45 0.5 0.55 V 150 170 °C 40 °C V [Current Limiter Circuit] Limiter voltage VRF VCC-VM [Thermal Shutdown Operation] Thermal shutdown operating TSD temperature Hysteresis Design target value* (junction temperature) ∆TSD Design target value* (junction temperature) *: Design target value and no measurement was made. Continued on next page. No.A0333-2/12 LB11692JH Continued from preceding page. Ratings Parameter Symbol Conditions unit min typ max [CTL Amplifier] Input offset voltage Input bias current Common-mode input voltage range VIO(CTL) -10 IB(CTL) VICM High-level output voltage VOH(CTL) ITOC = -0.2mA Low-level output voltage VOL(CTL) ITOC = 0.2mA G(CTL) f(CTL) = 1kHz Open-loop gain 10 mV -1 1 µA 0 VREG-1.7 V VREG-1.2 VREG-0.8 0.8 45 V 1.05 51 V dB [PWM Oscillator Circuit] High-level output voltage VOH(PWM) 2.75 3.0 3.25 Low-level output voltage VOL(PWM) 1.1 1.3 1.4 V V(PWM) 1.5 1.7 2.0 Vp-p VPWM = 2.1V -120 -95 -70 µA f(PWM) C = 2200pF 16.5 21 27 kHz Input voltage 1 VTOC1 Output duty: 100% 2.72 3.0 3.30 V Input voltage 2 VTOC2 Output duty: 0% 1.07 1.3 1.45 V Input voltage 1L VTOC1L Design target value*. 100% when VREG = 4.7V 2.72 2.80 2.90 V Input voltage 2L VTOC2L Design target value*. 0% when VREG = 4.7V 1.07 1.17 1.27 V Input voltage 1H VTOC1H Design target value*. 100% when VREG = 5.3V 3.08 3.20 3.30 V Input voltage 2H VTOC2H Design target value*. 0% when VREG = 5.3V 1.21 1.33 1.45 V VOL(RD) IRD = 5mA 0.1 0.3 V IL(RD) VRD = 28V 10 µA VOL(FG) IFG = 5mA IL(FG) VFG = 28V Amplitude External capacitor charge current Oscillator frequency ICHG V [TOC Pin] [RD Pin] Low-level output voltage Output leakage current [FG Pin] Low-level output voltage Output leakage current 0.1 0.3 V 10 µA [FGFIL Pin] Charge current IFGFIL1 -7 -5 -3 µA Discharge current IFGFIL2 3 5 7 µA High-level input voltage VIH(SS) 2.0 VREG V Low-level input voltage VIL(SS) 0 1.0 V Input open voltage VIO(SS) 2.6 2.9 3.2 V Hysteresis VIS(SS) 0.16 0.25 0.34 V High-level input current IIH(SS) VS/S = VREG 100 130 µA Low-level input current IIL(SS) VS/S = 0V -170 -130 [S/S Pin] µA [PWMIN Pin] Input frequency range f(PI) 50 kHz High-level input voltage range VIH(PI) 2.0 VREG V Low-level input voltage range VIL(PI) 0 1.0 V Input open voltage VIO(PI) 2.6 2.9 3.2 V Hysteresis VIS(PI) 0.16 0.25 0.34 V High-level input current IIH(PI) VPWMIN = VREG 100 130 µA Low-level input current IIL(PI) VPWMIN = 0V -170 µA -130 [F/R Pin] High-level input voltage VIH(FR) 2.0 VREG V Low-level input voltage VIL(FR) 0 1.0 V Input open voltage VIO(FR) VREG-0.5 VREG V Hysteresis VIS(FR) 0.16 0.25 0.34 V High-level input current IIH(FR) VF/R = VREG -10 0 10 µA Low-level input current IIL(FR) VF/R = 0V -165 -115 µA *: Design target value and no measurement was made. No.A0333-3/12 LB11692JH Package Dimensions unit : mm (typ) 3251 17.8 (6.2) Allowable Power Dissipation, Pd max - W 19 1 18 2.0 0.3 0.25 2.45max (2.25) 0.8 0.65 (4.9) 7.9 10.5 36 (0.5) Pd max - Ta 2.4 2.1 2.0 1.6 1.2 1.09 Independent IC 0.9 0.8 0.47 0.4 0 -40 0.1 2.7 Mounted on a specified board: 114.3mm×76.1mm×1.6mm glass epoxy -20 0 20 40 60 Ambient Temperature, Ta -°C 80 100 ILB01760 SANYO : HSOP36R(375mil) Truth Table F/R = ”L” Source→Sink F/R = “H” IN1 IN2 IN3 IN1 IN2 IN3 1 OUT2→OUT1 H L H L H L 2 OUT3→OUT1 H L L L H H 3 OUT3→OUT2 H H L L L H 4 OUT1→OUT2 L H L H L H 5 OUT1→OUT3 L H H H L L 6 OUT2→OUT3 L L H H H L NC OUT1 F/R IN3+ IN3- IN2+ IN2- IN1+ IN1- GND1 PWM NC TOC EI- EI+ S/S NC 35 34 33 32 31 30 29 28 27 26 25 24 23 22 21 20 19 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 OUT3 NC GND2 NC NC VD VCC VM VREG LVS FGFIL NC FC CSD FG RD PWMIN FRAME OUT2 36 NC FRAME Pin Assignment Top view No.A0333-4/12 LB11692JH Block Diagram FG EI- CTL TOC FG - EI+ RD + RD FC CSD LVS CSD CIRCUIT FG CIRCUIT VCC LVSD RD VCC CTL AMP TSD PWM PWM OSC VD Rd CURR LIM COMP PWMIN VM Rf OUT1 CONTROL CIRCUIT PWMIN DRIVER BGP GND1 VREF FILTER 5VREG VREG F/R S/S S/S HALL AMP & MATRIX F/R FGFIL VREG IN1 IN2 OUT2 OUT3 IN3 GND2 Pin Functions Pin No. Symbol 34 OUT1 36 OUT2 2 OUT3 4 GND2 Pin Description Motor drive output Equivalent Circuit VCC VD Motor drive output system ground 7 VD Low side output transistor drive current supply 9 VM Motor drive output power supply and output current 300Ω VM 2 7 9 34 36 detection. Connect a resistor (Rf) between this pin and VCC. The output current is limited to a value determined 4 by the equation IOUT = VRF/Rf. 8 VCC Power supply (Systems other than the motor drive output) 10 VREG 5V regulator output (control circuit power supply). Connect a capacitor (about 0.1µF) between this pin and VCC ground for stabilization. 10 Continued on next page. No.A0333-5/12 LB11692JH Continued from preceding page. Pin No. 11 Symbol LVS Pin Description Undervoltage protection voltage detection. Equivalent Circuit VREG Connect this pin to VREG if the VREG level is to be detected. If the VCC level is to be detected, insert a zener diode in 52kΩ series to set the detection level. 9.5kΩ 11 12 FGFIL FG filter. Normally, this IC will be used with this pin open. VREG Connect a capacitor between this pin and ground if noise on the FG signal becomes a problem. 300Ω 12 14 FC Control loop frequency characteristics correction. VREG Connect a capacitor between this pin and ground. 300Ω 14 15 CSD Constraint protection circuit operating time setting. VREG 300Ω 15 16 FG Hall input 1FG output. (This is an open-collector output.) VREG 16 Continued on next page. No.A0333-6/12 LB11692JH Continued from preceding page. Pin No. 17 Symbol RD Pin Description Equivalent Circuit Motor constrained state detection output VREG (This is an open-collector output.) When the motor is constrained: high, when the motor is 17 turning: low. 18 PWM IN PWM pulse input. VREG When low the output will be on and when high or open the outputs will be off. If this pin is used to control this IC, 30kΩ connect EI- to ground and connect EI+ to TOC. 5kΩ 40kΩ 18 S/S Start/stop control. Low: start, high or open: stop. VREG 30kΩ 20 5kΩ 40kΩ 20 21 EI+ CTL amplifier noninverting input 22 EI- CTL amplifier inverting input VREG 300Ω 300Ω 21 TOC PWM waveform comparator (CTL amplifier output) VREG 23 40kΩ 23 22 PWM comparator Continued on next page. No.A0333-7/12 LB11692JH Continued from preceding page. Pin No. 25 Symbol PWM Pin Description PWM oscillator frequency setting. Connect a capacitor between this pin and ground. Equivalent Circuit VREG A frequency of about 21kHz can be set by using a 2200pF capacitor. 1kΩ 200Ω 26 GND1 25 Ground (For circuits other than the motor drive output system) 28 IN1+ Hall effect sensor inputs 27 IN1- High when IN+ > IN-, low for the reverse state. 30 IN2+ Signal inputs with an amplitude (differential) of at least 29 IN2- 100mVp-p are desirable for the Hall inputs. 32 IN3+ If noise is a problem, connect capacitors between 31 IN3- the IN+ and IN- inputs. VREG 300Ω 300Ω 27 29 31 33 F/R Forward/reverse control VREG 40kΩ Low: forward, high or open: reverse. 28 30 32 3.5kΩ 33 1,3 NC 5,6 No connection. The NC pins may be used for wiring connections. 13,19 24,35 FRAME Frame connection The FRAME pin is connected internally to the IC surface metal parts. Both must be used in the electrically open state. No.A0333-8/12 LB11692JH LB11692JH Overview 1. Output Drive Circuit The LB11692JH uses a direct PWM drive technique. Since the motor speed can be controlled by holding the supply voltage constant and changing the output duty, the power supply design can be simplified compared to designs used with techniques that vary the supply voltage (such as PAM drive). The low side output transistor is switched with a pulse-width modulated signal and the drive output is adjusted by changing the duty. The LB11692JH includes builtin output diodes for the regenerative currents that occur when the PWM signal is off and during phase switching. 2. Power Supply Stabilization Since the LB11692JH uses a control method based on PWM switching, the power supply lines are susceptible to disruption. Electrolytic capacitors with an adequate capacitance for stabilization must be connected between VCC and ground. If diodes are inserted in the power supply lines to prevent destruction of the equipment if the power supply is connected in reverse, the power supply lines will be particularly susceptible to disruption. In this case, even larger capacitors must be used. The connected electrolytic capacitors must be located as close as possible to the IC pins (VCC, VM, and GND2). If the electrolytic capacitors cannot be attached close to the pins due to problems with the heat sink or other issues, ceramic capacitors of about 0.1µF must be attached close to the pins. 3. VREG Pin At the same time as being the 5V regulator output, the VREG pin is also the power supply for the IC internal control circuits. Therefore, a capacitor of at least 0.1µF must be connected between the VREG pin and ground to stabilize the control circuit power supply. The ground side of the connected capacitor must be connected to the GND1 pin with as short a line as possible. 4. FC Pin The capacitor connected to the FC pin is required to correct the control loop's frequency characteristics. (It should be about 0.1µF.) 5. VD Pin The VD pin supplies the low side output transistor drive current (a maximum of about 0.1A). The IC internal power consumption is suppressed by connecting a resistor between the VCC and VD pins and dividing power consumption due to the low side output transistor drive current with that resistor. Although the IC internal power consumption due to the drive current can be reduced by lowering the VD pin voltage, a voltage of at least 4V must be assured at the VD pin. Use a resistor in the range from about 50Ω (0.5W) to about 100Ω (1W) between the VCC and VD pins when the LB11692JH is used with VCC = 24V. 6. Hall Effect Sensor Input Signals Signals with amplitudes greater than 80mVp-p are required for the Hall effect sensor inputs. If possible, we recommend providing signal amplitudes in excess of 100mVp-p to minimize the effects of noise. Add capacitors across the Hall inputs (between the + and - sides of each input) if the output waveforms are disrupted by noise during phase switching. 7. Current Limiter Circuit The current limiter circuit limits the peak value of the output current to a current determined by the equation I = VRF/Rf (where VRF = 0.5V (typical), Rf = current detection resistor value). When the limiter operates, it suppresses the current by PWM control of the low side output transistor at the PWM frequency determined by the external capacitor connected to the PWM pin, in particular, by reducing the on duty. No.A0333-9/12 LB11692JH 8. Forward/Reverse Switching The LB11692JH was designed assuming that forward/reverse switching would not be performed while the motor is operating. We recommend that the F/R pin be held fixed at either the low (forward) or high (reverse) level when the motor is turning. Although it will be pulled up to the high level by an internal pull-up resistor (about 40kΩ) when left open, this must be strengthened by an external resistor if fluctuations are large. If the direction is switched while the motor is turning, large currents will flow due to the braking operation. The LB11692JH's current limiter circuit, however, cannot limit this braking current. Therefore, forward/reverse switching during motor rotation is only possible if the braking current is limited to a value under IO max (1.8A) by the motor coil resistance or other circuit or phenomenon. Furthermore, since through current will flow in the high and low side transistors at the instant the switch occurs with switching that only uses the F/R pin, applications must provide a rive off period for switching directions. A drive off period must be provided by either setting the IC to the stopped state with the S/S pin or setting the PWM signal to the 0% duty state with the TOC and PWMIN pins, and the F/R pin must only be switched during that period to prevent through current. 9. Power Saving Circuit This IC can be set to a power saving state in which current consumption is reduced by setting it to the stopped state with the S/S pin. The bias current to most of the circuits in the IC is cut off in this power saving state. Note, however, that the 5V regulator output is still provided in the power saving state. 10. Notes on the PWM Frequency The PWM frequency is determined by the capacitance (F) of the capacitor connected to the PWM pin. fPWM ≈ 1/ (21700×C) A frequency in the range 15 to 25kHz is desirable for the PWM frequency. The ground side of the connected capacitor must be connected to the GND1 pin by as short a line as possible. 11. Control Methods The output duty can be controlled by either of the following methods. • Comparison of the TOC pin voltage with the PWM oscillator waveform This method determines the low side output transistor duty according to the result of comparing the TOC pin voltage with the PWM oscillator waveform. The PWM duty will be 0% when the TOC pin voltage is under about 1.3V and will be 100% when that voltage is over about 3.0V. Since the TOC pin is the output of the CTL amplifier, a control voltage cannot be directly input to the TOC pin. Accordingly, the CTL amplifier is normally used as a full feedback amplifier (by connecting the EI- pin to the TOC pin) and inputting a DC voltage to the EI pin (here the TOC voltage will be equal to the EI+ pin voltage). When the EI+ pin voltage increases, the output duty will increase as well. Since the motor will be driven if the EI+ pin is in the open state, a pull-down resistor should be connected to the EI+ pin in applications where this is not desirable. A low level must be input to the PWMIN pin (or it must be connected to ground) if the TOC pin voltage control system is used. • PWMIN pulse input A 15 to 25kHz frequency pulse signal can be input to the PWMIN pin and the low side output transistor duty can be controlled based on the duty of that input signal. When the PWMIN pin is low, the output will be on, and when high, the output will be off. When the PWMIN pin is open, the input will go to the high level and the output will be off. If PWMIN pin control is used, the EI- pin must be connected to ground and the EI+ pin must be connected to the TOC pin. No.A0333-10/12 LB11692JH 12. Undervoltage Protection Circuit The undervoltage protection circuit turns off the low side output transistor To the detected if the LVS pin voltage falls below the circuit's operating voltage (about 3.8V). power supply This operating voltage is the detection level for a 5V system. The detection level can be increased by connecting a zener diode in series with the LVS pin To the LVS pin to apply a level shift to the detection level. The current flowing into the LVS pin during detection is about 65µA. To suppress variations in the zener voltage, it is necessary to stabilize the rise of the zener diode voltage by increasing the current that flows in the zener diode. If this is necessary, insert a resistor between the LVS pin and ground. When the LCS pin is open, it will be pulled to the ground level by the built-in pull-down resistor and the output will be turned off. Thus if the undervoltage protection circuit is not used, a voltage in excess of the release voltage (about 4.3V) must be applied to the LVS pin. Note that the maximum rating for the LVS pin voltage is 30V. 13. Motor Constraint Protection Circuit When motor motion is constrained, the external capacitor connected to the CSD pin will be alternately charged (up to about 3.0V) with a constant current of about 2.4µA and discharged with a constant current of about 0.17µA (to about 1.0V). Thus the CSD pin voltage will have a sawtooth waveform. The motor constraint protection circuit turns the motor (the low side output transistor) on or off repeatedly based on this sawtooth waveform. Motor drive will be on during the period the CSD pin external capacitor is being charged from about 1.0V to about 3.0V and will be off when it is being discharged from about 3.0V to about 1.0V. The drive on/off operation protects the IC and the motor when the motor is physically constrained from moving. If a 0.47µF capacitor is connected to the CSD pin, the IC will iterate an on/off cycle in which drive is on for about 0.4 seconds and off for about 5.5 seconds. While the motor is turning, the CSD pin voltage will be held at a certain voltage (that depends on the motor speed) by (a) a CSD pin external capacitor discharge operation based on about 10µs discharge pulses generated internally in the IC when the Hall input IN1 switches (that is, on rising and falling edges on the FG output) and (b) a charge operation on that capacitor by a constant current of about 2.4µA. Since the Hall input IN1 does not switch when the motor is physically constrained, the discharge pulses are not generated and the CSD pin external capacitor will be charged to about 3.0V by the constant current of about 2.4µA. The motor constraint protection circuit operates when the capacitor reaches about 3.0V. The constraint protection operation will be released when the motor constraint is released. If the motor speed is extremely low, the CSD pin voltage during that motor rotation will be held at a comparatively high voltage, and if that voltage reaches about 3.0V, the constraint protection function will operate. Since the constraint protection function will operate if the Hall input IN1 frequency falls below about 10Hz, caution is required when using the motor constraint protection circuit with motors that will operate at low speeds. Connect the CSD pin to ground if the motor constraint protection circuit is not used. No.A0333-11/12 LB11692JH Specifications of any and all SANYO Semiconductor products described or contained herein stipulate the performance, characteristics, and functions of the described products in the independent state, and are not guarantees of the performance, characteristics, and functions of the described products as mounted in the customer's products or equipment. To verify symptoms and states that cannot be evaluated in an independent device, the customer should always evaluate and test devices mounted in the customer's products or equipment. SANYO Semiconductor Co., Ltd. strives to supply high-quality high-reliability products. However, any and all semiconductor products fail with some probability. It is possible that these probabilistic failures could give rise to accidents or events that could endanger human lives, that could give rise to smoke or fire, or that could cause damage to other property. When designing equipment, adopt safety measures so that these kinds of accidents or events cannot occur. Such measures include but are not limited to protective circuits and error prevention circuits for safe design, redundant design, and structural design. In the event that any or all SANYO Semiconductor products (including technical data,services) described or contained herein are controlled under any of applicable local export control laws and regulations, such products must not be exported without obtaining the export license from the authorities concerned in accordance with the above law. No part of this publication may be reproduced or transmitted in any form or by any means, electronic or mechanical, including photocopying and recording, or any information storage or retrieval system, or otherwise, without the prior written permission of SANYO Semiconductor Co., Ltd. Any and all information described or contained herein are subject to change without notice due to product/technology improvement, etc. When designing equipment, refer to the "Delivery Specification" for the SANYO Semiconductor product that you intend to use. Information (including circuit diagrams and circuit parameters) herein is for example only; it is not guaranteed for volume production. SANYO Semiconductor believes information herein is accurate and reliable, but no guarantees are made or implied regarding its use or any infringements of intellectual property rights or other rights of third parties. This catalog provides information as of December, 2006. Specifications and information herein are subject to change without notice. PS No.A0333-12/12