74V1T66 SINGLE BILATERAL SWITCH ■ ■ ■ ■ ■ ■ ■ HIGH SPEED: tPD = 0.3ns (TYP.) at VCC = 5V LOW POWER DISSIPATION: ICC = 1µA(MAX.) at TA = 25°C LOW "ON" RESISTANCE: RON = 6.5Ω (TYP.) AT VCC = 5V, II/O = 1mA SINE WAVE DISTORTION: 0.04% AT VCC = 5V, f = 1KHz COMPATIBLE WITH TTL OUTPUTS ON CONTROL PIN: VIH = 2V (MIN), VIL = 0.8V (MAX) OPERATING VOLTAGE RANGE: VCC(OPR) = 4.5V to 5.5V IMPROVED LATCH-UP IMMUNITY DESCRIPTION The 74V1T66 is an advanced high-speed CMOS SINGLE BILATERAL SWITCH fabricated in silicon gate C2MOS technology. It achieves high speed propagation delay and VERY LOW ON resistances while maintaining true CMOS low power consumption. This bilateral switch handles rail to rail analog and digital signals that may vary across the full power supply range (from GND to VCC). The C input is provided to control the switch and it’s compatible with standard TTL output; the switch is ON (port I/O is connected to Port O/I) SOT23-5L SOT323-5L ORDER CODES PACKAGE T&R SOT23-5L SOT323-5L 74V1T66STR 74V1T66CTR when the C input is held high and OFF (high impedance state exists between the two ports) when C is held low. It can be used in many application as Battery Powered System, Test Equipment. It’s available in the commercial and extended temperature range in SOT23-5L and SOT323-5L package. All inputs and output are equipped with protection circuits against static discharge, giving them ESD immunity and transient excess voltage. PIN CONNECTION AND IEC LOGIC SYMBOLS April 2004 1/11 74V1T66 INPUT EQUIVALENT CIRCUIT PIN DESCRIPTION PIN N° SYMBOL NAME AND FUNCTION 1 2 I/O O/I 4 C 3 GND VCC Independent Input/Output Independent Output/Input Enable Input (Active HIGH) Ground (0V) 5 Positive Supply Voltage TRUTH TABLE CONTROL SWITCH FUNCTION H L ON OFF * * High Impedance State ABSOLUTE MAXIMUM RATINGS Symbol VCC VI Parameter Supply Voltage DC Input Voltage VIC DC Control Input Voltage VO DC Output Voltage IIK DC Input Diode Current Value Unit -0.5 to +7.0 V -0.5 to VCC + 0.5 V -0.5 to +7.0 V -0.5 to VCC + 0.5 V ± 20 mA IIK DC Control Input Diode Current - 20 mA IOK DC Output Diode Current ± 20 mA IO DC Output Current ± 50 mA ± 50 mA -65 to +150 °C 300 °C ICC or IGND DC VCC or Ground Current Tstg Storage Temperature TL Lead Temperature (10 sec) Absolute Maximum Ratings are those values beyond which damage to the device may occur. Functional operation under these conditions is not implied RECOMMENDED OPERATING CONDITIONS Symbol Value Unit Supply Voltage 4.5 to 5.5 V Input Voltage 0 to VCC V VIC Control Input Voltage 0 to 5.5 V VO Output Voltage 0 to VCC V Top Operating Temperature -55 to 125 °C 0 to 20 ns/V VCC VI dt/dv Parameter Input Rise and Fall Time (note 1) VCC = 5.0V 1) VIN from 0.8V to 2V on control pin 2/11 74V1T66 DC SPECIFICATIONS Test Condition Symbol VIH VIL RON RON IOFF IIZ IIN ICC Parameter High Level Input Voltage Low Level Input Voltage ON Resistance Switch Input Leakage Current (SWITCH ON, OUTPUT OPEN) Control Input Leakage Current Quiescent Supply Current TA = 25°C VCC (V) Min. Typ. Max. 2 5.0(*) -40 to 85°C -55 to 125°C Min. Min. Max. 2 5.0(*) Unit Max. 2 V 0.8 0.8 0.8 V 5.0(*) VIC = VIH VI/O = VCC to GND II/O ≤ 1mA 7.5 10 12 14 Ω 5.0(*) VIC = VIH VI/O = VCC or GND II/O ≤ 1mA 6.5 8.5 10 12 Ω 5.5 VOS = VCC to GND VIS = VCC to GND VIC = VIL ±0.1 ±1 ±5 µA 5.5 VOS = VCC to GND VIC = VIH ±0.1 ±1 ±5 µA 0 to 5.5 VIC = 5.5V or GND ± 0.1 ± 1.0 ± 1.0 µA 5.5 VI = VCC or GND 1 10 20 µA ON Resistance Input/Output Leakage Current (SWITCH OFF) Value (*) Voltage range is 5V ± 0.5V AC ELECTRICAL CHARACTERISTICS (CL = 50pF, Input tr = tf = 3ns) Test Condition Symbol Parameter Value TA = 25°C VCC (V) -55 to 125°C Min. Min. Max. tr = tf = 6ns 0.3 0.6 1.0 2.0 ns 5.0(*) RL = 500 Ω 5.0 7.5 9.0 10.0 ns 5.0(*) RL = 1 KΩ 2.0 4.0 5.0 7.0 ns Delay Time 5.0(*) tPLZ tPHZ Output Disable Time tPZL tPZH Output Enable Time Max. Unit Typ. tPD Min. -40 to 85°C Max. (*) Voltage range is 5.0V ± 0.5V 3/11 74V1T66 CAPACITIVE CHARACTERISTICS Test Condition Symbol Value TA = 25°C Parameter Min. CIN Input Capacitance CI/O Output Capacitance Power Dissipation Capacitance (note 1) CPD Typ. Max. 3 10 -40 to 85°C -55 to 125°C Min. Min. Max. 10 Unit Max. 10 pF 10 pF 3 pF 1) CPD is defined as the value of the IC’s internal equivalent capacitance which is calculated from the operating current consumption without load. (Refer to Test Circuit). Average operating current can be obtained by the following equation. ICC(opr) = CPD x VCC x fIN + ICC ANALOG SWITCH CHARACTERISTICS (GND = 0V; TA = 25°C) Test Condition Symbol fMAX Parameter Sine Wave Distortion (THD) Frequency Response (Switch ON) VIN (Vp-p) 5.0(*) 4 Unit Typ. fIN = 1 KHz RL = 10 KΩ, CL = 50 pF 0.04 % 5.0(*) Adjust fIN voltage to obtain 0 dB at VOS. Increase fIN Frequency until dB meter reads -3dB RL = 50Ω, CL = 10 pF 180 MHz Feed through Attenuation (Switch OFF) 5.0(*) VIN is centered at VCC/2 Adjust fIN Voltage to obtained 0dBm at VIS RL = 600Ω, CL = 50 pF, fIN = 1KHz sine wave -60 dB Crosstalk (Control Input to Signal Output) 5.0(*) RL = 600Ω, CL = 50 pF, fIN = 1KHz square wave tr = tf = 6ns 60 mV (*) Voltage range is 5.0V ± 0.5V 4/11 VCC (V) Value 74V1T66 SWITCHING CARACTERISTICS TEST CIRCUIT FEEDTHROUGH ATTENUATION BANDWIDTH ATTENUATION MAXIMUM CONTROL FREQUENCY CROSSTALK (control to output 5/11 74V1T66 CHANNEL RESISTANCE (RON) 6/11 ICC (Opr.) 74V1T66 SOT23-5L MECHANICAL DATA mm. mils DIM. MIN. TYP MAX. MIN. TYP. MAX. A 0.90 1.45 35.4 57.1 A1 0.00 0.10 0.0 3.9 A2 0.90 1.30 35.4 51.2 b 0.35 0.50 13.7 19.7 C 0.09 0.20 3.5 7.8 D 2.80 3.00 110.2 118.1 E 1.50 1.75 59.0 68.8 e 0.95 37.4 H 2.60 3.00 102.3 118.1 L 0.10 0.60 3.9 23.6 . 7049676C 7/11 74V1T66 SOT323-5L MECHANICAL DATA mm. mils DIM. MIN. MAX. MIN. TYP. MAX. A 0.80 1.10 31.5 43.3 A1 0.00 0.10 0.0 3.9 A2 0.80 1.00 31.5 39.4 b 0.15 0.30 5.9 11.8 C 0.10 0.18 3.9 7.1 D 1.80 2.20 70.9 86.6 E 1.80 2.40 70.9 94.5 E1 1.15 1.35 45.3 53.1 e 0 .65 25.6 e1 1.3 51.2 L 8/11 TYP 0.10 0.30 3.9 11.8 74V1T66 Tape & Reel SOT23-xL MECHANICAL DATA mm. inch DIM. MIN. TYP A MAX. MIN. TYP. 180 13.0 7.086 C 12.8 D 20.2 0.795 N 60 2.362 T 13.2 MAX. 0.504 0.512 14.4 0.519 0.567 Ao 3.13 3.23 3.33 0.123 0.127 0.131 Bo 3.07 3.17 3.27 0.120 0.124 0.128 Ko 1.27 1.37 1.47 0.050 0.054 0.0.58 Po 3.9 4.0 4.1 0.153 0.157 0.161 P 3.9 4.0 4.1 0.153 0.157 0.161 9/11 74V1T66 Tape & Reel SOT323-xL MECHANICAL DATA mm. inch DIM. MIN. TYP MAX. MIN. TYP. MAX. A 175 180 185 6.889 7.086 7.283 C 12.8 13 13.2 0.504 0.512 0.519 D 20.2 N 59.5 0.795 60 T 10/11 60.5 2.362 14.4 0.567 Ao 2.25 0.088 Bo 2.7 0.106 Ko 1.2 0.047 Po 3.9 4 4.1 0.153 0.157 0.161 P 3.8 4 4.2 0.149 0.157 0.165 74V1T66 Information furnished is believed to be accurate and reliable. However, STMicroelectronics assumes no responsibility for the consequences of use of such information nor for any infringement of patents or other rights of third parties which may result from its use. No license is granted by implication or otherwise under any patent or patent rights of STMicroelectronics. Specifications mentioned in this publication are subject to change without notice. This publication supersedes and replaces all information previously supplied. STMicroelectronics products are not authorized for use as critical components in life support devices or systems without express written approval of STMicroelectronics. The ST logo is a registered trademark of STMicroelectronics All other names are the property of their respective owners © 2004 STMicroelectronics - All Rights Reserved STMicroelectronics GROUP OF COMPANIES Australia - Belgium - Brazil - Canada - China - Czech Republic - Finland - France - Germany - Hong Kong - India - Israel - Italy - Japan Malaysia - Malta - Morocco - Singapore - Spain - Sweden - Switzerland - United Kingdom - United States. http://www.st.com 11/11