M74HC4316 QUAD BILATERAL SWITCH ■ ■ ■ ■ ■ ■ ■ ■ ■ HIGH SPEED: tPD = 13ns (TYP.) at VCC = 6V LOW POWER DISSIPATION: ICC = 1µA(MAX.) at Vcc = 5V LOW "ON" RESISTANCE: 120Ω TYP. (VCC - VEE = 2V) 50Ω TYP. (VCC - VEE = 4.5V) 35Ω TYP. (VCC - VEE = 9V) WIDE ANALOG INPUT VOLTAGE RANGE ± 6v LOW CROSSTALK BETWEEN SWITCHES FAST SWITCHING SINE WAVE DISTORTION: 0.020 at VCC - VEE = 9V HIGH NOISE IMMUNITY: VNIH = V NIL = 28 % VCC (MIN.) PIN AND FUNCTION COMPATIBLE WITH 74 SERIES 4316 DESCRIPTION The M74HC4316 is an high speed CMOS QUAD BILATERAL SWITCH fabricated with silicon gate C2MOS technology. This device has four independent analogue switches. Each switch has two input/output terminals (nI/O, nO/I) and an active high select input (nC). DIP SOP TSSOP ORDER CODES PACKAGE TUBE DIP SOP TSSOP M74HC4316B1R M74HC4316M1R T&R M74HC4316RM13TR M74HC4316TTR When the enable input is high, all four analog switches are off. The supply voltage for the digital signals applied to VCC and GND must be whitin the range 0 to 6 V. The voltage swing on the analogue Inputs/Outputs can be between VCC (positive limit) and VEE (negative limit). The voltage between VCC and VEE must not exceed 12V. All inputs are equipped with protection circuits against static discharge and transient excess voltage. PIN CONNECTION AND IEC LOGIC SYMBOLS July 2001 1/11 M74HC4316 LOGIC DIAGRAM PIN DESCRIPTION PIN No SYMBOL NAME AND FUNCTION 1, 4, 10, 13 1 to 4 I/O 2, 3, 11, 12 1 to 4 O/I 7 E 15, 5, 6, 14 1C to 4C 9 VEE Negative Supply Voltage 8 16 GND VCC Ground (0V) Independent Inputs/Outputs Independent Outputs/ Inputs Enable Inputs (Active LOW) Enable Inputs (Active High) Positive Supply Voltage TRUTH TABLE E C SWITCH FUNCTION L L H H L X ON OFF OFF ABSOLUTE MAXIMUM RATINGS Symbol Value Unit Supply Voltage -0.5 to +7 V VCC - VEE Supply Voltage -0.5 to +13 V VCC VI VI/O Parameter Control Input Voltage Switch Input/Output Voltage -0.5 to VCC + 0.5 V VEE -0.5 to VCC + 0.5 V IIK DC Input Diode Current ± 20 mA IOK DC Output Diode Current ± 20 mA IO DC Output Source Sink Current Per Output Pin ± 25 mA ± 50 mA ICC or IGND DC VCC or Ground Current PD Power Dissipation Tstg Storage Temperature TL Lead Temperature (10 sec) 500(*) mW -65 to +150 °C 300 °C Absolute Maximum Ratings are those values beyond which damage to the device may occur. Functional operation under these conditions is not implied (*) 500mW at 65 °C; derate to 300mW by 10mW/°C from 65°C to 85°C 2/11 M74HC4316 RECOMMENDED OPERATING CONDITIONS Symbol Parameter Value Unit VCC Supply Voltage 2 to 12 V VEE Supply Voltage -6 to 0 V VCC - VEE Supply Voltage 2 to 12 V Input Voltage 0 to VCC V VI/O Switch I/O Voltage 0 to VCC V Top Operating Temperature -55 to 125 °C VI Input Rise and Fall Time tr, tf VCC = 2.0V 0 to 1000 VCC = 4.5V 0 to 500 VCC = 6.0V 0 to 400 ns DC SPECIFICATIONS Test Condition Symbol VIHC VILC RON ∆RON IOFF IIZ IIN Parameter High Level Control Input Voltage Low Level Control Input Voltage ON Resistance Difference of ON Resistance between switches Input/Output Leakage Current (SWITCH OFF) Switch Input Leakage Current (SWITCH ON, OUTPUT OPEN) Control Input Current VCC (V) 2.0 4.5 6.0 2.0 4.5 6.0 4.5 4.5 6.0 2.0 4.5 4.5 6.0 4.5 4.5 6.0 6.0 6.0 Value TA = 25°C VEE (V) Min. Typ. Max. 1.5 3.15 4.2 GND -4.5 -6.0 GND GND -4.5 -6.0 GND -4.5 -6.0 GND VI = VIHC VI/O = VCC to VEE II/O = 0.1mA VI = VIHC VI/O = VCC or VEE II/O = 0.1mA VIN = VIHC or VILC VI/O = VCC to VEE II/O = 0.1mA GND 6.0 -6.0 VIN = VIHC or VILC 6.0 VI = VCC or GND -55 to 125°C Unit Min. Min. Max. 1.5 3.15 4.2 70 50 30 120 50 35 20 10 5 5 VOS = VCC or GND VIS = VCC or GND -6.0 VIN = VIHC or VILC 6.0 -40 to 85°C VOS = VCC or GND 10-5 Max. 1.5 3.15 4.2 V 0.5 1.35 1.8 170 85 70 180 80 60 40 15 10 10 ±0.06 ± 0.1 0.5 1.35 1.8 200 105 85 215 100 75 60 20 15 15 ± 0.6 ±1 0.5 1.35 1.8 ±0.06 ± 0.1 ± 0.6 ±1 ±2 ±2 µA ± 0.1 ±1 ±1 µA V Ω Ω ±2 ±2 µA 3/11 M74HC4316 AC ELECTRICAL CHARACTERISTICS (CL = 50 pF, Input tr = tf = 6ns) Test Condition Symbol ΦI/O tPZL tPZH tPLZ tPHZ fMAX Parameter Phase Difference Between Input and Output Output Enable Time (E, C - OUT) Output Disable Time (E, C - OUT) Maximum Control Input Frequency VCC (V) VEE (V) 2.0 4.5 6.0 4.5 6.0 2.0 4.5 6.0 4.5 6.0 2.0 4.5 6.0 4.5 6.0 2.0 4.5 6.0 GND GND GND -4.5 -6.0 GND GND GND -4.5 -6.0 GND GND GND -4.5 -6.0 GND GND GND Value TA = 25°C Min. -40 to 85°C -55 to 125°C Unit Typ. Max. 12 3 3 2 2 56 14 12 13 11 112 28 24 24 21 2 9 11 30 6 5 4 4 115 23 20 21 18 205 41 35 34 29 RL = 1KΩ RL = 1KΩ RL = 1KΩ CL = 15 pF VOUT = 1/2 VCC Min. Max. Min. Max. 40 8 7 5 5 145 29 25 26 23 255 51 43 43 36 ns ns ns MHz CAPACITIVE CHARACTERISTICS Test Condition Symbol Parameter CIN Input Capacitance CI/O Switch Terminal Capacitance Feed Through Capacitance Power Dissipation Capacitance (note 1) CIOS CPD TA = 25°C VCC (V) 4.5 4.5 Value Min. -4.5 -4.5 5.0 Typ. Max. 5 10 -40 to 85°C -55 to 125°C Min. Min. Max. 10 Unit Max. 10 pF 5 pF 1 pF 16 pF GND 1) CPD is defined as the value of the IC’s internal equivalent capacitance which is calculated from the operating current consumption without load. (Refer to Test Circuit). Average operating current can be obtained by the following equation. ICC(opr) = CPD x VCC x fIN + ICC 4/11 M74HC4316 ANALOG SWITCH CHARACTERISTICS (GND = 0V;TA = 25°C) Symbol Parameter Sine Wave Distortion (THD) fMAX Frequency Response (Switch ON) Feed through Attenuation (Switch OFF) Crosstalk (Control Input to Signal Output) Crosstalk (Between Any Switches) Test Condition VIN (Vp-p) Value Unit VCC (V) VEE (V) 2.25 4.5 6.0 2.25 4.5 6.0 2.25 4.5 6.0 2.25 4.5 6.0 2.25 4.5 6.0 2.25 4 0.025 fIN = 1 KHz RL = 10 KΩ, CL = 50 pF 4.5 8 0.020 % 6.0 11 0.018 28 2.25 Adjust fIN voltage to obtain 0 dBm at VOS. Increase f Frequency until dB meter reads -3dB 4.5 42 MHz IN RL = 50Ω, CL = 10 pF, fIN = 1MHz sine wave 6.0 43 -50 2.25 VIN is centered at VCC/2. Adjust input for 0 dBm RL = 600Ω, CL = 50 pF, fIN = 1MHz sine wave 4.5 -50 dB 6.0 -50 2.25 4.5 RL = 600Ω, CL = 50 pF, fIN = 1MHz square wave (tr = tf =6ns) 5 mV 6.0 -50 2.25 Adjust VIN to Obtain 0 dBm at input RL = 600Ω, CL = 50 pF, fIN = 1MHz sine wave 4.5 -50 dB 6.0 -50 Typ. 5/11 M74HC4316 SWITCHING CARACTERISTICS TEST CIRCUIT CONTROL ENABLE CROSSTALK (control to output) CROSSTALK BETWEEN ANY TWO SWITCHES BANDWIDTH AND FEEDTHROUGH ATTENUATION MAXIMUM CONTROL FREQUENCY 6/11 M74HC4316 CHANNEL RESISTANCE (RON) ICC (Opr.) 7/11 M74HC4316 Plastic DIP-16 (0.25) MECHANICAL DATA mm. inch DIM. MIN. a1 0.51 B 0.77 TYP MAX. MIN. TYP. MAX. 0.020 1.65 0.030 0.065 b 0.5 0.020 b1 0.25 0.010 D 20 0.787 E 8.5 0.335 e 2.54 0.100 e3 17.78 0.700 F 7.1 0.280 I 5.1 0.201 L Z 3.3 0.130 1.27 0.050 P001C 8/11 M74HC4316 SO-16 MECHANICAL DATA DIM. mm. MIN. TYP A a1 inch MAX. MIN. TYP. 1.75 0.1 0.068 0.2 a2 MAX. 0.003 0.007 1.65 0.064 b 0.35 0.46 0.013 0.018 b1 0.19 0.25 0.007 0.010 C 0.5 0.019 c1 45° (typ.) D 9.8 10 0.385 0.393 E 5.8 6.2 0.228 0.244 e 1.27 0.050 e3 8.89 0.350 F 3.8 4.0 0.149 0.157 G 4.6 5.3 0.181 0.208 L 0.5 1.27 0.019 0.050 M S 0.62 0.024 8° (max.) PO13H 9/11 M74HC4316 TSSOP16 MECHANICAL DATA mm. inch DIM. MIN. TYP A MAX. MIN. TYP. MAX. 1.2 A1 0.05 A2 0.8 b 0.047 0.15 0.002 0.004 0.006 1.05 0.031 0.039 0.041 0.19 0.30 0.007 0.012 c 0.09 0.20 0.004 0.0089 D 4.9 5 5.1 0.193 0.197 0.201 E 6.2 6.4 6.6 0.244 0.252 0.260 E1 4.3 4.4 4.48 0.169 0.173 0.176 1 e 0.65 BSC K 0° L 0.45 A 0.60 0.0256 BSC 8° 0° 0.75 0.018 8° 0.024 0.030 A2 A1 b e K c L E D E1 PIN 1 IDENTIFICATION 1 0080338D 10/11 M74HC4316 Information furnished is believed to be accurate and reliable. However, STMicroelectronics assumes no responsibility for the consequences of use of such information nor for any infringement of patents or other rights of third parties which may result from its use. No license is granted by implication or otherwise under any patent or patent rights of STMicroelectronics. Specifications mentioned in this publication are subject to change without notice. This publication supersedes and replaces all information previously supplied. STMicroelectronics products are not authorized for use as critical components in life support devices or systems without express written approval of STMicroelectronics. © The ST logo is a registered trademark of STMicroelectronics © 2001 STMicroelectronics - Printed in Italy - All Rights Reserved STMicroelectronics GROUP OF COMPANIES Australia - Brazil - China - Finland - France - Germany - Hong Kong - India - Italy - Japan - Malaysia - Malta - Morocco Singapore - Spain - Sweden - Switzerland - United Kingdom © http://www.st.com 11/11