EVL6562A-400W L6562A 400W FOT-controlled PFC pre-regulator evaluation board Data Brief Features ■ Line voltage range: 90 to 265 Vac ■ Minimum line frequency (fL): 47 Hz ■ Regulated output voltage: 400 V ■ Rated output power: 400 W ■ Maximum 2fL output voltage ripple: 10 V pk-pk ■ Hold-up time: 22 ms (VDROP after hold-up time: 300 V) ■ Maximum switching frequency: 85 kHz (@Vin= 90 Vac, Pout= 400 W) ■ Minimum estimated efficiency: 90% (@Vin= 90 Vac, Pout= 400 W) ■ Maximum ambient temperature: 50 °C ■ EMI: in accordance with EN55022 Class-B ■ PCB type and size: single side,70 µm,CEM1,148.5x132 mm ■ EVL6562A-400W Table 1. Low profile design: 35 mm component maximum height Device summary Order code EVL6562A-400W Description The board implements a 400 W, wide-range mains input, PFC pre-conditioner suitable for ATX PSU, Flat screen displays, etc. To make possible the use of a low-cost device like the L6562A at this power level, usually prohibitive for TM PFC, the chip operates with Fixed-Off-Time control. This allows continuous conduction mode operation, normally achievable with more expensive control chips and more complex control architectures. For technical details and demoboard performance, please refer to the available application note. February 2008 Rev 1 For further information contact your local STMicroelectronics sales office. 1/9 www.st.com 9 Circuit schematic 1 EVL6562A-400W Circuit schematic Figure 1. EVL6562A-400W schematic L3 DM-51uH-6A D2 D15XB60 CM-1.5mH-5A F1 ~ L1 J1 D1 + 8A/250V 1 2 R1 C1 C2 C3 C4 C5 1M5 470nF-X2 470nF 680nF-X2 470nF-630V 470nF-630V ~ 5-6 +400Vdc T 1N5406 PQ40-500uH 1-2 D3 R2 STTH8R06 NTC 2R5-S237 J2 8 90 - 265Vac 11 C6 470nF-630V 1 2 3 4 5 C7 330uF-450V +400Vdc +400Vdc NC RTN RTN +400Vout R3 100K R5 47R +400Vdc R9 R10 510k 510k R4 100K R102 C10 22N 0R0 D4 LL4148 R11 D5 BZX85-C18 510k R12 C13 220nF C11 C12 470nF/50V 100uF/50V R13 47K R36 3R9 12k C14 2.2uF R14 47k D7 LL4148 Q1 STP12NM50FP 1 2 3 4 INV VCC COMP GD MULT GND CS ZCD L6562A R17 6R8 8 7 R35 3R9 LL4148 D6 6 C15 68pF D8 LL4148 Q2 STP12NM50FP 5 R18 6R8 R15 1k8 R31 3k C16 120pF R16 30k R19 1K0 R32 R33 620k 620k Q3 BC857C C20 R34 C21 10k 10nF 330pF R101 0R0 ● 2/9 Boost inductor spec. (Delta Electronics 86H-5410B): – vertical 6+6, PQ40+30 ferrite – 1 mm gap for 500 µH primary inductance – Primary: 65 turns 30x0.2 mm – Secondary: 5 turns 0.28 mm R20 R21 0R47-1W 0R47-1W R22 0R47-1W R23 0R47-1W EVL6562A-400W 2 Circuit layout Circuit layout Figure 2. PCB layout(a) PFC PRECONDITIONER USING L6562A FOT a. Not in scale 3/9 Typical performance EVL6562A-400W 3 Typical performance Figure 3. EVL6562A-400W compliance to EN61000-3-2 standard @full load Measurements @ 230Vac Full load Figure 4. EN61000-3-2 class D limits Measurements @ 230Vac Full load 1 0.1 0.01 1 0.1 0.01 0.001 0.001 0.0001 0.0001 1 3 5 7 9 11 13 15 17 19 21 23 25 27 29 31 33 35 37 39 1 3 5 7 9 11 13 15 17 19 21 23 25 27 29 31 33 35 37 39 Harmonic Order (n) Figure 5. Harmonic Order (n) EVL6562A-400W compliance to EN61000-3-2 standard @70W load Measurements @ 230Vac 70W Figure 6. EN61000-3-2 class D limits EVL6562A-400W compliance to JEIDA-MITI standard @70W load Measurements @ 230Vac 70W EN61000-3-2 class D limits 1 Harmonic current (A) 1 Harmonic current (A) EN61000-3-2 class D limits 10 Harmonic current (A) 10 Harmonic current (A) EVL6562A-400W compliance to JEIDA-MITI standard @full load 0.1 0.01 0.001 0.1 0.01 0.001 0.0001 0.0001 1 3 5 7 9 11 13 15 17 19 21 23 25 27 29 31 33 35 37 39 1 3 5 7 9 11 13 15 17 19 21 23 25 27 29 31 33 35 37 39 Harmonic Order (n) Figure 7. Harmonic Order (n) Power factor vs. Vin and load Figure 8. 35 1.00 30 0.95 25 0.90 20 PF THD (%) 1.05 0.85 THD vs. Vin and load 15 Pout = 400W 0.80 10 Pout = 400W Pout = 200W 0.75 Pout = 200W 5 Pout = 70W Pout = 70W 0.70 80 4/9 130 180 Vin (Vac) 230 280 0 80 130 Vin (Vac) 180 230 280 EVL6562A-400W Appendix A Table 2. Bill of material Bill of material Bill of material Ref. Part type Case/ des. part value package C1 470 nF- x2 DWG X2 film capacitor R46-I 3470--M1- ARCOTRONICS C10 22 nF 1206 100 V SMD cercap - general purpose AVX C11 470 nF/50 V 1206 50 V SMD cercap - general purpose AVX C12 100 µF/50 V Dia 8x11 (mm) Aluminium elcap - yxf series - 105°C RUBYCON C13 220 nF 0805 50 V SMD cercap - general purpose AVX C14 2.2 µF 1206 50V SMD cercap - general purpose AVX C15 100 pF 0805 50 V SMD cercap - general purpose AVX C16 120 pF 0805 50 V SMD cercap - general purpose AVX C2 470 nF-x2 DWG X2 film capacitor R46-I 3470--M1- ARCOTRONICS C20 330 pF 0805 50 V SMD cercap - general purpose AVX C21 10 nF 1206 50 V SMD cercap - general purpose AVX C3 680 nF-x2 DWG X2 film capacitor R46-I 3680--M1- ARCOTRONICS C4 470 nF-630 V DWG film capacitor MKP - B32653A6474J EPCOS C5 470 nF-630 V DWG film capacitor MKP - B32653A6474J EPCOS C6 470 nF-630 V DWG film capacitor MKP- B32653A6474J EPCOS C7 330 µF-450 V C8 Res DWG Not used - C9 Res DWG Not used - D1 1N5406 DO-201 Standard recovery rectifier VISHAY D2 D15XB60 DWG Rectifier bridge SHINDENGEN D3 STTH8R06 TO-220FP Ultrafast high voltage rectifier STMICROELECTRONICS D4 LL4148 MINIMELF Fast switching diode VISHAY D5 BZX85-C18 MINIMELF Zener diode VISHAY D6 LL4148 MINIMELF Fast switching diode VISHAY D7 LL4148 MINIMELF Fast switching diode VISHAY D8 LL4148 MINIMELF Fast switching diode VISHAY F1 8 A/250 V 5 x 20 mm 8 A mains input fuse WICKMANN J1 3-pins conn. (central rem.) P 3.96 KK series MOLEX J2 5-pins conn. (central rem.) P 3.96 KK series MOLEX JP101 Jumper Description Dia 35x35 (mm) Aluminium ELCAP - LLS series - 85°C Supplier NICHICON Wire jumper 5/9 Bill of material Table 2. EVL6562A-400W Bill of material (continued) Ref. Part type Case/ des. part value package JP102 Jumper L1 CM-1.5 mH-5 A DWG CM CHOKE - LFR2205B DELTA ELECTRONICS L2 Res DWG Not used - L3 DM-51 µH-6A DWG FILTER INDUCTOR - LSR2306-1 DELTA ELECTRONICS L4 PQ40-500 µH DWG PFC inductor - 86 H-5410B DELTA ELECTRONICS Q1 STP12NM50FP TO-220FP N-channel Power MOSFET STMICROELECTRONICS Q2 STP12NM50FP TO-220FP N-channel Power MOSFET STMICROELECTRONICS Q3 BC857C SOT-23 Small signal BJT - PNP VISHAY R1 1M5 AXIAL HV resistor BC COMPONENTS R10 510 kΩ 1206 SMD std film res - 1% - 250ppm/°C BC COMPONENTS R11 510 kΩ 1206 SMD std film res - 1% - 250ppm/°C BC COMPONENTS R12 47 kΩ 0805 SMD std film res - 1% - 250ppm/°C BC COMPONENTS R13 12 kΩ 0805 SMD std film res - 1% - 250ppm/°C BC COMPONENTS R14 47 kΩ 0805 SMD std film res - 5% - 250ppm/°C BC COMPONENTS R15 1 k8Ω 0805 SMD std film res - 1% - 100ppm/°C BC COMPONENTS R16 30 kΩ 0805 SMD std film res - 1% - 100ppm/°C BC COMPONENTS R17 6R8 0805 SMD std film res - 5% - 250ppm/°C BC COMPONENTS R18 6R8 0805 SMD std film res - 5% - 250ppm/°C BC COMPONENTS R19 1 KΩ 1206 SMD std film res - 5% - 250ppm/°C BC COMPONENTS R2 NTC 2R5 DWG NTC resistor 2R5 S237 EPCOS R20 0R47-1 W AXIAL AXIAL res - 5% - 250ppm/°C BC COMPONENTS R21 0R47-1 W AXIAL AXIAL res - 5% - 250ppm/°C BC COMPONENTS R22 0R47-1 W AXIAL AXIAL res - 5% - 250ppm/°C BC COMPONENTS R23 0R47-1 W AXIAL AXIAL res - 5% - 250ppm/°C BC COMPONENTS R25 Res 1206 Not used - R3 100 KΩ 1206 SMD std film res - 5% - 250ppm/°C BC COMPONENTS R31 3 kΩ 0805 SMD std film res - 1% - 100ppm/°C BC COMPONENTS R32 620 kΩ 1206 SMD std film res - 5% - 250ppm/°C BC COMPONENTS R33 620 kΩ 1206 SMD std film res - 5% - 250ppm/°C BC COMPONENTS R34 10 kΩ 1206 SMD std film res - 5% - 250ppm/°C BC COMPONENTS R35 3R9 0805 SMD std film res - 5% - 250ppm/°C BC COMPONENTS R36 3R9 0805 SMD std film res - 5% - 250ppm/°C BC COMPONENTS R4 100 KΩ 1206 SMD std film res - 5% - 250ppm/°C BC COMPONENTS R5 47R 1206 SMD std film res - 5% - 250ppm/°C BC COMPONENTS 6/9 Description Supplier Wire jumper EVL6562A-400W Table 2. Bill of material Bill of material (continued) Ref. Part type Case/ des. part value package R9 510 kΩ 1206 SMD std film res - 1% - 250ppm/°C BC COMPONENTS R101 0R0 1206 SMD std film res - 5% - 250ppm/°C BC COMPONENTS R102 0R0 1206 SMD std film res - 5% - 250ppm/°C BC COMPONENTS U1 L6562A SO-8 Transition-mode PFC controller STMICROELECTRONICS Description Supplier 7/9 Revision history 4 EVL6562A-400W Revision history Table 3. 8/9 Document revision history Date Revision 07-Feb-2008 1 Changes Initial release. EVL6562A-400W Please Read Carefully: Information in this document is provided solely in connection with ST products. STMicroelectronics NV and its subsidiaries (“ST”) reserve the right to make changes, corrections, modifications or improvements, to this document, and the products and services described herein at any time, without notice. All ST products are sold pursuant to ST’s terms and conditions of sale. Purchasers are solely responsible for the choice, selection and use of the ST products and services described herein, and ST assumes no liability whatsoever relating to the choice, selection or use of the ST products and services described herein. No license, express or implied, by estoppel or otherwise, to any intellectual property rights is granted under this document. If any part of this document refers to any third party products or services it shall not be deemed a license grant by ST for the use of such third party products or services, or any intellectual property contained therein or considered as a warranty covering the use in any manner whatsoever of such third party products or services or any intellectual property contained therein. UNLESS OTHERWISE SET FORTH IN ST’S TERMS AND CONDITIONS OF SALE ST DISCLAIMS ANY EXPRESS OR IMPLIED WARRANTY WITH RESPECT TO THE USE AND/OR SALE OF ST PRODUCTS INCLUDING WITHOUT LIMITATION IMPLIED WARRANTIES OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE (AND THEIR EQUIVALENTS UNDER THE LAWS OF ANY JURISDICTION), OR INFRINGEMENT OF ANY PATENT, COPYRIGHT OR OTHER INTELLECTUAL PROPERTY RIGHT. UNLESS EXPRESSLY APPROVED IN WRITING BY AN AUTHORIZED ST REPRESENTATIVE, ST PRODUCTS ARE NOT RECOMMENDED, AUTHORIZED OR WARRANTED FOR USE IN MILITARY, AIR CRAFT, SPACE, LIFE SAVING, OR LIFE SUSTAINING APPLICATIONS, NOR IN PRODUCTS OR SYSTEMS WHERE FAILURE OR MALFUNCTION MAY RESULT IN PERSONAL INJURY, DEATH, OR SEVERE PROPERTY OR ENVIRONMENTAL DAMAGE. ST PRODUCTS WHICH ARE NOT SPECIFIED AS "AUTOMOTIVE GRADE" MAY ONLY BE USED IN AUTOMOTIVE APPLICATIONS AT USER’S OWN RISK. Resale of ST products with provisions different from the statements and/or technical features set forth in this document shall immediately void any warranty granted by ST for the ST product or service described herein and shall not create or extend in any manner whatsoever, any liability of ST. ST and the ST logo are trademarks or registered trademarks of ST in various countries. Information in this document supersedes and replaces all information previously supplied. The ST logo is a registered trademark of STMicroelectronics. All other names are the property of their respective owners. © 2008 STMicroelectronics - All rights reserved STMicroelectronics group of companies Australia - Belgium - Brazil - Canada - China - Czech Republic - Finland - France - Germany - Hong Kong - India - Israel - Italy - Japan Malaysia - Malta - Morocco - Singapore - Spain - Sweden - Switzerland - United Kingdom - United States of America www.st.com 9/9