STCS2A 2 A max constant current LED driver Features ■ Up to 40 V input voltage ■ Less than 0.5 V voltage overhead ■ Up to 2 A output current ■ PWM dimming pin ■ Shutdown pin ■ LED disconnection diagnostic ■ Slope control with external cap 10 1 PowerSO-10 Applications ■ LED constant current supplying for varying input voltages ■ Low voltage lighting ■ Small appliances LED lighting ■ Car LED lights Description The STCS2A is a BiCMOS constant current source designed to provide a precise constant current starting from a varying input voltage source. The main target is to replace discrete components Table 1. July 2008 solution for driving LEDs in low voltage applications such as 5 V, 12 V or 24 V giving benefits in terms of precision, integration and reliability. The current is set with external resistor up to 2 A with a ± 10 % precision; a dedicated pin allows implementing PWM dimming. An external capacitor allows setting the slope for the current rise from tens of microseconds to tens of milliseconds allowing reduction of EMI. An open-drain pin output provides information on load disconnection condition. Device summary Order code Package Packaging STCS2ASPR PowerSO-10 600 parts per reel Rev 3 1/18 www.st.com 18 Contents STCS2A Contents 1 Application diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 2 Pin configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 3 Maximum ratings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 4 Electrical characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 5 Timing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 6 Typical performance characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 7 Detail description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10 8 7.1 Current setting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10 7.2 Enable . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10 7.3 PWM dimming . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10 7.4 Diagnostic . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11 Application information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12 8.1 Reverse polarity protection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12 8.2 Thermal considerations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12 9 Package mechanical data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14 10 Revision history . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17 2/18 STCS2A Application diagram 1 Application diagram Figure 1. Typical application diagram for 2 A LED current VIN 4.5V up to 40V BAT46ZFILM RIN 100 ohm CBYP 0.1µF ON VCC DRAIN PWM STCS2A OFF ON OFF CDRAIN 0.47µF EN DISC Load disconnection (Open Drain output) SLOPE CSLOPE 10nF GND FB SOURCE RFB 0.05 ohm 3/18 Pin configuration STCS2A 2 Pin configuration Figure 2. Pin connections (top view) Table 2. Pin description Pin n° Symbol 1 VCC 2 PWM 3 EN Shutdown 4 NC No connect 5 DRAIN 6 SOURCE 7 FB 8 GND 9 SLOPE 10 DISC exp-pad 4/18 Note Supply voltage PWM dimming input Internal N-MOSFET drain Internal N-MOSFET source. Reference voltage is 100 mV. An external resistor between SOURCE and GND pins sets different current levels for different application needs Feedback input. The control loop regulates the current in such a way that the average voltage at the FB input is 100 mV (nominal). The cathode of the LED and a resistor to ground to set the LED current should be connected at this point Ground Capacitor for slope control Load disconnection flag (open drain) Internally connected to ground STCS2A Maximum ratings 3 Maximum ratings Table 3. Absolute maximum ratings Symbol Parameter VCC Value Unit DC supply voltage -0.3 to +45 Drain pin -0.3 to +45 SOURCE Source pin -0.3 to + 3.3 V PWM, EN, DISC Logic pins -0.3 to + VCC + 3.3 V -0.3 to + 3.3 V ±2 kV V DRAIN SLOPE, FB Configuration pins ESD Human body model (all pins) TJ (1) Junction temperature -40 to 150 °C TSTG Storage temperature range -55 to 150 °C 1. TJ is calculated from the ambient temperature TA and the power dissipation PD according the following formula: TJ = TA + (PD x RthJA). See Figure 16. for details of max power dissipation for ambient temperatures higher than 25 °C. Note: Absolute maximum ratings are those values beyond which damage to the device may occur. Functional operation under these conditions is not implied. Table 4. Thermal data Symbol RthJC Parameter Thermal resistance junction-case PowerSO-10 Unit 2 °C/W RthJA Thermal resistance junction-ambient (1) 50 °C/W RthJA Thermal resistance junction-ambient (2) 35 °C/W RthJA Thermal resistance junction-ambient (3) 12 °C/W 1. FR4 with using the recommended pad-layout 2. FR4 with heat sink on board (6 cm2). 3. FR4 with copper-filled through holes and external heat sink applied. 5/18 Electrical characteristics STCS2A 4 Electrical characteristics Table 5. Electrical characteristics (VCC = 12 V; IO = 100 mA; TJ = -40 °C to 125 °C; VDRAIN = 1 V; CDRAIN = 1 µF; CBYP = 100 nF typical values are at TA = 25°C, unless otherwise specified) Symbol VCC IO VFB Parameter Test conditions Min. VDROP TD 40 V Output current range 1 2000 mA Output current RFB = 50 mΩ Regulation (percentage with respect to VCC = 12 V) VCC = 4.5 to 40 V, IO = 100 mA; VDRAIN = 1 V -1 Feedback voltage IO = 0 to 2A 90 Quiescent current (Measured on VCC pin) Dropout voltage (VDRAIN to GND) Rise/Fall time of the current on PWM transition 2 % 100 110 mV 450 750 Shutdown Mode; VCC = 5 to 12V 1 Shutdown Mode; VCC = 12 to 40V 3 IO = 100 mA 0.12 0.16 IO = 2 A 0.58 0.9 µA V Shutdown; VDRAIN = 40 V 10 CSLOPE = 10 nF, TJ = -40 °C to 105 °C 800 3 VPWM falling, VCC = 12 V CSLOPE = floating 1.2 Low level voltage ISINK = 5 mA 0.2 Leakage current VDISC = 5 V Load disconnection threshold (VDRAIN-GND) DISC Turn-ON 75 DISC Turn-OFF 110 Delay on PWM signal (Figure 1) A +1 VPWM rising, VCC = 12 V CSLOPE = floating DISC Thermal Protection Unit 4.5 LEAKDRAIN Drain leakage current TR/TF Max. Supply voltage range On Mode ICC Typ. µA µs µs 0.5 V 1 µA mV Shutdown temperature 155 Hysteresis 25 °C Logic inputs (PWM and EN) VL Input low level VH Input high level Note: 6/18 0.4 1.2 V V EN, PWM leakage current VEN = 5 V; VPWM = 5 V 2 EN input leakage current VEN = 40 V 60 PWM input leakage current VPWM = 40 V 120 µA All devices 100 % production tested at TA = 25 °C. Limits over the operating temperature range are guaranteed by design. STCS2A Timing 5 Timing Figure 3. PWM and output current timing PWM 90% Current 10% Trise TD Figure 4. TD Block diagram High Voltage 45 V VCC Tfall Preregulator 3.3 V Low Voltage 3.3 V H.V. 45 V Thermal Shutdown Bandgap 1.23 V DISC Shutdown all blocks + 75 mV EN Enable Input PWM PWM Input Enable, PWM & Slope controll Logic Disc comp DRAIN + Logic 100 mV Comp GND Slope Control SLOPE Driver SOURCE FB 7/18 Typical performance characteristics STCS2A 6 Typical performance characteristics Figure 5. IDRAIN vs VCC, TA = 25°C Figure 6. IDRAIN vs RSET 1000 IDRAIN [mA] 100 10 1 0.1 1 10 RFB [Ω] Figure 7. IDRAIN vs temperature Figure 8. Figure 9. ICC vs temperature Figure 10. ICC vs VCC 8/18 VDROP (including VFB) vs temperature 100 STCS2A Typical performance characteristics Figure 11. Trise/Tfall vs CSLOPE Figure 12. Turn-on time Figure 13. Dimming operation: Rise Figure 14. Dimming operation: Fall CSLOPE = 1 nF CSLOPE = 1 nF 9/18 Detail description 7 STCS2A Detail description The STCS2A is a BiCMOS constant current source designed to provide a precise constant current starting from a varying input voltage source. The main target is to replace discrete components solution for driving LEDs in low voltage applications such as 5 V, 12 V or 24 V giving benefits in terms of precision, integration and reliability. 7.1 Current setting The current is set with an external sensing resistor connected to the FB pin. The feedback voltage is 100 mV, then a low resistor value can be chosen reducing power dissipation. A value between 1 mA and 2 A can be set according to the resistor value the resulting output current has a tolerance of ± 10%. For instance, should one need a 700 mA LEDs current, RF should be selected according to the following equation: RF = VFB / ILEDs = 100 mV / 700 mA = 142 mΩ 7.2 Enable When the enable pin is low the device completely off thus reducing current consumption to less than 1 µA. When in shutdown mode, the internal main switch is off. 7.3 PWM dimming The PWM input allows implementing PWM dimming on the LED current; when the PWM input is high the main switch will be on and vice versa. A typical frequency range for the input is from few Hertz to 50 kHz. The maximum dimming frequency is limited by the minimum rise/fall time of the current (obtained with CSLOPE=0) which is around 4 µs each. Above 50 kHz the current waveforms starts assuming a triangular shape. While the PWM input is switching, the overall circuitry remains on, this is needed in order to implement two important features: short delay time and controlled slope for the current. Since the PWM pin is controlling just the main switch, the overall circuitry is always on and it is able to control the delay time between the PWM input signal and the output current in the range of few µs, this is important to implement synchronization among several light LED sources. The rise and fall slope of the current is controlled by the CSLOPE capacitor. The rise and fall time are linear dependent from the CSLOPE capacitor value (see graph in typical characteristics). A controlled rise time has two main benefits: reducing EMI noise and avoid current spike at turn on. When CSLOPE is left floating, the internal switch is turned on at maximum speed, in this condition an overshoot can be present on the LED current before the system goes into regulation. 10/18 STCS2A 7.4 Detail description Diagnostic When STCS2A is in on mode (EN is high), the device is able to detect disconnection or fail of the LED string monitoring VDRAIN pin. If VDRAIN is lower than 75 mV the DISC pin is pulled low regardless the PWM pin status. This information can be used by the system to inform that some problem happens in the LEDs. 11/18 Application information STCS2A 8 Application information 8.1 Reverse polarity protection STCS2A must be protected from reverse connection of the supply voltage. Since the current sunk from VCC pin is in the range of 450 µA a small diode connected to VCC is able to protect the chip. Care must be taken for the whole application circuit, especially for the LEDs, in fact, in case a negative voltage is applied between VIN and GND, a negative voltage will be applied to the LED string that must have a total breakdown voltage higher than the negative applied voltage in order to avoid any damage. Figure 15. Reverse polarity condition VIN BAT46 or similar DRAIN VCC DISC PWM EN + SLOPE CSLOPE 8.2 GND FB SOURCE RSENSE Thermal considerations The STCS2A is able to control a LED current up to 2 A and able to sustain a voltage on the drain pin up to 40 V. Those operating conditions are however limited by thermal constraints. The poor thermal conduction of epoxy FR4 boards does not permit to benefit of the outstanding thermal performance of the PowerSO-10. In any case one way to improve the thermal conduction is the use of large heat spreader areas at the copper layer of the PC board. This leads to a reduction of thermal resistance to 30 - 36 °C/W for 3 to 6 cm2 on-board heatsink. Use of copper-filled through holes on conventional FR4 techniques increases the metallization and decreases thermal resistance accordingly. Using a configuration with 16 holes under the spreader of the package with a pitch of 1.8 mm and a diameter of 0.7 mm, the thermal resistance (junction - heatsink) can be reduced to 12 °C/W. The thermal resistances shown in the Error! Reference source not found. section are the typical ones. The power dissipation in the device can be calculated as follow: 12/18 STCS2A Application information PD = (VDRAIN - VFB) x ILED + (VCC x ICC) basing on this and on the thermal resistance and ambient temperature, the junction temperature can be calculated as: TJ = RthJA x PD + TA A typical application could be: – Input voltage: 12 V; – 3 white LEDs with an typical VF = 3.6 V; – LEDs current: 1000 mA; – Package: PowerSO-10; – TA = 50 °C; In this case the drain voltage is given by: VDRAIN = 12 - 3 x 3.6 = 1.2 V end the power dissipated in the IC is the following: PD = (1.2 - 0.1) x 1 + 12 x 0.5 x 10-3 = 1.1 W With a thermal resistance junction-ambient equal to 12 °C/W the junction temperature is: TJ = 12 x 1.1 + 50 = 63 °C. The following pictures show the maximum power dissipation according to the ambient temperature: Figure 16. Maximum power dissipation vs TA for PowerSO-10 12.00 PDMAX = (TJMAX-TA)/RthJA PDMAX [W] 10.00 RthJA [°C/W] 12 8.00 35 6.00 4.00 2.00 0.00 25 35 45 55 65 75 85 95 105 115 125 [°C] 13/18 Package mechanical data 9 STCS2A Package mechanical data In order to meet environmental requirements, ST offers these devices in ECOPACK® packages. These packages have a lead-free second level interconnect. The category of second Level Interconnect is marked on the package and on the inner box label, in compliance with JEDEC Standard JESD97. The maximum ratings related to soldering conditions are also marked on the inner box label. ECOPACK is an ST trademark. ECOPACK specifications are available at: www.st.com. 14/18 STCS2A Package mechanical data PowerSO-10 Mechanical Data Dim. mm. Min. Typ. inch. Max. Min. Typ. Max. A 3.70 0.146 A1 0.10 0.004 A2 3.40 3.60 0.134 0.142 A3 1.25 1.35 0.049 0.053 b 0.40 0.53 0.016 0.021 c 0.35 0.55 0.014 0.022 D 9.40 9.60 0.370 0.378 D1 7.40 7.60 0.291 0.299 E 13.80 14.40 0.543 0.567 E1 9.30 9.50 0.366 0.374 E2 7.20 7.60 0.283 0.299 E3 5.90 6.10 0.232 0.240 e 1.27 0.050 L 0.95 1.65 0.037 0.065 α 0° 8° 0° 8° 0068039-E 15/18 Package mechanical data STCS2A Tape & Reel PowerSO-10 Mechanical Data mm. inch. Dim. Min. A Max. Min. 330 13.2 Typ. Max. 12.992 C 12.8 D 20.2 0.795 N 60 2.362 T 16/18 Typ. 0.504 30.4 0.519 1.197 Ao 14.9 15.1 0.587 0.594 Bo 9.9 10.1 0.390 0.398 Ko 4.15 4.35 0.163 0.171 Po 3.9 4.1 0.153 0.161 P 23.9 24.1 0.941 0.949 W 23.7 24.3 0.933 0.957 STCS2A Revision history 10 Revision history Table 6. Document revision history Date Revision Changes 19-Feb-2008 1 Initial release. 28-May-2008 2 Modified: Table 3 on page 5. 02-Jul-2008 3 Modified: Table 5 on page 6. 17/18 STCS2A Please Read Carefully: Information in this document is provided solely in connection with ST products. STMicroelectronics NV and its subsidiaries (“ST”) reserve the right to make changes, corrections, modifications or improvements, to this document, and the products and services described herein at any time, without notice. All ST products are sold pursuant to ST’s terms and conditions of sale. Purchasers are solely responsible for the choice, selection and use of the ST products and services described herein, and ST assumes no liability whatsoever relating to the choice, selection or use of the ST products and services described herein. No license, express or implied, by estoppel or otherwise, to any intellectual property rights is granted under this document. If any part of this document refers to any third party products or services it shall not be deemed a license grant by ST for the use of such third party products or services, or any intellectual property contained therein or considered as a warranty covering the use in any manner whatsoever of such third party products or services or any intellectual property contained therein. UNLESS OTHERWISE SET FORTH IN ST’S TERMS AND CONDITIONS OF SALE ST DISCLAIMS ANY EXPRESS OR IMPLIED WARRANTY WITH RESPECT TO THE USE AND/OR SALE OF ST PRODUCTS INCLUDING WITHOUT LIMITATION IMPLIED WARRANTIES OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE (AND THEIR EQUIVALENTS UNDER THE LAWS OF ANY JURISDICTION), OR INFRINGEMENT OF ANY PATENT, COPYRIGHT OR OTHER INTELLECTUAL PROPERTY RIGHT. UNLESS EXPRESSLY APPROVED IN WRITING BY AN AUTHORIZED ST REPRESENTATIVE, ST PRODUCTS ARE NOT RECOMMENDED, AUTHORIZED OR WARRANTED FOR USE IN MILITARY, AIR CRAFT, SPACE, LIFE SAVING, OR LIFE SUSTAINING APPLICATIONS, NOR IN PRODUCTS OR SYSTEMS WHERE FAILURE OR MALFUNCTION MAY RESULT IN PERSONAL INJURY, DEATH, OR SEVERE PROPERTY OR ENVIRONMENTAL DAMAGE. ST PRODUCTS WHICH ARE NOT SPECIFIED AS "AUTOMOTIVE GRADE" MAY ONLY BE USED IN AUTOMOTIVE APPLICATIONS AT USER’S OWN RISK. Resale of ST products with provisions different from the statements and/or technical features set forth in this document shall immediately void any warranty granted by ST for the ST product or service described herein and shall not create or extend in any manner whatsoever, any liability of ST. ST and the ST logo are trademarks or registered trademarks of ST in various countries. Information in this document supersedes and replaces all information previously supplied. The ST logo is a registered trademark of STMicroelectronics. All other names are the property of their respective owners. © 2008 STMicroelectronics - All rights reserved STMicroelectronics group of companies Australia - Belgium - Brazil - Canada - China - Czech Republic - Finland - France - Germany - Hong Kong - India - Israel - Italy - Japan Malaysia - Malta - Morocco - Singapore - Spain - Sweden - Switzerland - United Kingdom - United States of America www.st.com 18/18