STCS05A 0.5 A max constant current LED driver Features ■ Up to 40 V input voltage ■ Less than 0.5 V voltage overhead ■ Up to 0.5 A output current ■ PWM dimming pin ■ Shutdown pin ■ LED disconnection diagnostic ■ Slope control with external cap SO-8 Applications ■ LED constant current supplying for varying input voltages ■ Low voltage lighting ■ Small appliances LED lighting ■ Car LED lights components solution for driving LEDs in low voltage applications such as 5 V, 12 V or 24 V giving benefits in terms of precision, integration and reliability. The current is set with external resistor up to 0.5 A with a ± 10 % precision; a dedicated pin allows implementing PWM dimming. An external capacitor allows setting the slope for the current rise from tens of microseconds to tens of milliseconds allowing reduction of EMI. Description The STCS05A is a BiCMOS constant current source designed to provide a precise constant current starting from a varying input voltage source. The main target is to replace discrete Table 1. July 2008 An open-drain pin output provides information on load disconnection condition. Device summary Order code Package Packaging STCS05ADR SO-8 2500 parts per reel Rev 2 1/18 www.st.com 18 Contents STCS05A Contents 1 Application diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 2 Pin configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 3 Maximum ratings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 4 Electrical characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 5 Timing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 6 Typical performance characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 7 Detail description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10 8 7.1 Current setting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10 7.2 Enable . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10 7.3 PWM dimming . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10 7.4 Diagnostic . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11 Application information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12 8.1 Reverse polarity protection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12 8.2 Thermal considerations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12 9 Package mechanical data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14 10 Revision history . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17 2/18 STCS05A Application diagram 1 Application diagram Figure 1. Typical application diagram for 0.5 A LED current VIN 4.5V to 40V BAT46ZFILM RIN 100 ohm CBYP 0.1µF ON PWM OFF ON OFF DRAIN VCC STCS05A CDRAIN 0.47µF EN DISC Load disconnection (Open Drain output) SLOPE GND CSLOPE 10nF FB RFB 0.2 ohm 3/18 Pin configuration STCS05A 2 Pin configuration Figure 2. Pin connections (top view) Table 2. Pin description Pin n° Symbol 1 VCC 2 PWM 3 EN 4 DRAIN 5 FB 6 GND 7 SLOPE 8 DISC 4/18 Note Supply voltage PWM dimming input Shutdown pin Internal N-MOSFET drain Feedback input. The control loop regulates the current in such a way that the average voltage at the FB input is 100 mV (nominal). The cathode of the LED and a resistor to ground to set the LED current should be connected at this point. Ground Capacitor for slope control Load disconnection flag (open drain) STCS05A Maximum ratings 3 Maximum ratings Table 3. Absolute maximum ratings Symbol Parameter VCC Value Unit DC supply voltage -0.3 to +45 DRAIN Drain pin -0.3 to +45 PWM, EN, DISC Logic pins -0.3 to + VCC + 0.3 V -0.3 to + 3.3 V ±2 kV 0.85 W Junction temperature -40 to 150 °C Storage temperature range -55 to 150 °C V SLOPE, FB Configuration pins ESD Human body model (all pins) Power Dissipation TJ TSTG SO-8 TA=25°C (1) 1. See Figure 16 for details of max power dissipation for ambient temperature higher than 25 °C Note: Absolute maximum ratings are those values beyond which damage to the device may occur. Functional operation under these conditions is not implied. Table 4. Thermal data Symbol RthJC RthJA Parameter Thermal resistance junction-case Thermal resistance junction-ambient (1) SO-8 Unit 20 °C/W 100 °C/W 1. This value depends from thermal design of PCB on which the device is mounted. 5/18 Electrical characteristics STCS05A 4 Electrical characteristics Table 5. Electrical characteristics (VCC = 12 V; IO = 100 mA; TJ = -40 °C to 125 °C; VDRAIN = 1 V; CDRAIN = 1 µF; CBYP = 100 nF typical values are at TA = 25 °C, unless otherwise specified) Symbol VCC IO VFB Parameter Test conditions Min. VDROP TD 40 V Output current range 1 500 mA Output current RFB = 0.2 Ω Regulation (percentage with respect to VCC = 12 V) VCC = 4.5 to 40V, IO = 100mA; VDRAIN = 1V -1 Feedback Voltage IO = 0 to 0.5A 90 Quiescent current (Measured on VCC pin) Dropout voltage (VDRAIN to GND) Rise/Fall time of the current on PWM transition 500 % 100 110 mV 450 750 Shutdown Mode; VCC = 5 to 12V 1 Shutdown Mode; VCC = 12 to 40V 3 IO = 100mA 0.12 0.16 IO = 0.5A 0.58 0.9 µA V Shutdown; VDRAIN = 40V 10 CSLOPE = 10 nF, TJ = -40 °C to 105 °C 800 3 VPWM falling, VCC = 12V CSLOPE = floating 1.2 Low level voltage ISINK = 5mA 0.2 Leakage current VDISC = 5V Load disconnection threshold (VDRAIN-GND) DISC Turn-ON 75 DISC Turn-OFF 110 Delay on PWM signal (see Figure 3) mA +1 VPWM rising, VCC = 12V CSLOPE = floating, DISC Thermal Protection Unit 4.5 LEAKDRAIN Drain leakage current TR/TF Max. Supply voltage range On Mode ICC Typ. µA µs µs 0.5 V 1 µA mV Shutdown temperature 155 Hysteresis 25 °C Logic inputs (PWM and EN) VL Input low level VH Input high level Note: 6/18 0.4 1.2 V V EN, PWM leakage current VEN = 5V; VPWM = 5V 2 EN input leakage current VEN = 40V 60 PWM input leakage current VPWM = 40V 120 µA All devices 100 % production tested at TA = 25 °C. Limits over the operating temperature range are guaranteed by design. STCS05A Timing 5 Timing Figure 3. PWM and output current timing PWM 90% Current 10% TD Figure 4. Trise TD Block diagram High Voltage 45 V VCC Tfall Preregulator 3.3 V Low Voltage 3.3 V H.V. 45 V Thermal Shutdown Bandgap 1.23 V DISC Shutdown all blocks + 75 mV EN Enable Input PWM PWM Input Enable, PWM & Slope controll Logic Disc comp DRAIN + Logic 100 mV Comp GND Slope Control Driver FB SLOPE 7/18 Typical performance characteristics STCS05A 6 Typical performance characteristics Figure 5. IDRAIN vs VCC, TA = 25 °C Figure 6. IDRAIN vs RSET 1000 IDRAIN [mA] 100 10 1 0.1 1 10 RFB [Ω] Figure 7. IDRAIN vs temperature Figure 8. Figure 9. ICC vs temperature Figure 10. ICC vs VCC 8/18 VDROP (including VFB) vs temperature 100 STCS05A Typical performance characteristics Figure 11. Trise/Tfall vs CSLOPE Figure 12. Turn-on time IDRAIN = 80 mA - CSLOPE = 10nF - TA = 25° C VPWM 2V/DIV IDRAIN 20mA/DIV VDRAIN 1V/DIV Time 210µsec/DIV Figure 13. Rise time Figure 14. Fall time IDRAIN = 80 mA - CSLOPE = 10nF - TA = 25° C IDRAIN = 80 mA - CSLOPE = 10nF - TA = 25° C VPWM 2V/DIV VPWM 2V/DIV IDRAIN 20mA/DIV IDRAIN 20mA/DIV VDRAIN 1V/DIV VDRAIN 1V/DIV Time 200µsec/DIV Time 200µsec/DIV 9/18 Detail description 7 STCS05A Detail description The STCS05A is a BiCMOS constant current source designed to provide a precise constant current starting from a varying input voltage source. The main target is to replace discrete components solution for driving LEDs in low voltage applications such as 5 V, 12 V or 24 V giving benefits in terms of precision, integration and reliability. 7.1 Current setting The current is set with an external sensing resistor connected to the FB pin. The feedback voltage is 100 mV, then a low resistor value can be chosen reducing power dissipation. A value between 1 mA and 500 mA can be set according to the resistor value, the resulting output current has a tolerance of ± 10 %. For instance, should one need a 350 mA LEDs current, RF should be selected according to the following equation: RF = VFB / ILEDs = 100 mV / 350 mA = 284 mΩ 7.2 Enable When the enable pin is low the device completely off thus reducing current consumption to less than 1 µA. When in shutdown mode, the internal main switch is off. 7.3 PWM dimming The PWM input allows implementing PWM dimming on the LED current; when the PWM input is high the main switch will be on and vice versa. A typical frequency range for the input is from few Hertz to 50 kHz. The maximum dimming frequency is limited by the minimum rise/fall time of the current (obtained with CSLOPE = 0) which is around 4 µs each. Above 50 kHz the current waveforms starts assuming a triangular shape. While the PWM input is switching, the overall circuitry remains on, this is needed in order to implement two important features: short delay time and controlled slope for the current. Since the PWM pin is controlling just the main switch, the overall circuitry is always on and it is able to control the delay time between the PWM input signal and the output current in the range of few µs, this is important to implement synchronization among several light LED sources. The rise and fall slope of the current is controlled by the CSLOPE capacitor. The rise and fall time are linear dependent from the CSLOPE capacitor value (see graph in typical characteristics). A controlled rise time has two main benefits: reducing EMI noise and avoid current spike at turn on. When CSLOPE is left floating, the internal switch is turned on at maximum speed, in this condition an overshoot can be present on the LED current before the system goes into regulation. 10/18 STCS05A 7.4 Detail description Diagnostic When STCS05A is in on mode (EN is high), the device is able to detect disconnection or fail of the LED string monitoring VDRAIN pin. If VDRAIN is lower than 75 mV the DISC pin is pulled low regardless the PWM pin status. This information can be used by the system to inform that some problem happens in the LEDs. 11/18 Application information STCS05A 8 Application information 8.1 Reverse polarity protection STCS05A must be protected from reverse connection of the supply voltage. Since the current sunk from VCC pin is in the range of 450 µA a small diode connected to VCC is able to protect the chip. Care must be taken for the whole application circuit, especially for the LEDs, in fact, in case a negative voltage is applied between VIN and GND, a negative voltage will be applied to the LED string that must have a total breakdown voltage higher than the negative applied voltage in order to avoid any damage. Figure 15. Reverse polarity condition VIN BAT46 or similar DRAIN VCC PWM EN + 8.2 DISC SLOPE GND FB Thermal considerations The STCS05A is able to control a LED current up to 500 mA and able to sustain a voltage on the drain pin up to 40 V. Those operating conditions are however limited by thermal constraints, the thermal resistances shown in the thermal data section is the typical ones. The power dissipation in the device can be calculated as follow: PD = (VDRAIN - VFB) x ILED + (VCC x ICC) basing on this and on the thermal resistance and ambient temperature, the junction temperature can be calculated as: TJ = RthJA x PD + TA A typical application could be: – Input voltage: 12 V; – 3 white LEDs with an typical VF = 3.6 V; – LEDs current: 350 mA; – Package: SO-8; – TA = 50 °C; 12/18 STCS05A Application information In this case VDRAIN = 12 - 3 x 3.6 = 1.2 V PD = (1.2 - 0.1) x 0.35 + 12 x 0.5 x 10-3 = 0.385 + 6 x 10-3 = 391 mW The junction temperature will be: TJ = 100 x 0.391 + 50 = 89 °C For a correct operation of the chip, the junction temperature must not exceed 110 °C. The following pictures show the maximum power dissipation according to the ambient temperature: Figure 16. Maximum power dissipation vs TA for SO-8 1.40 RthJA = 100 [°C/W] PDMAX [W] 1.20 1.00 0.80 0.60 PDMAX = (TJMAX-TA)/RthJA 0.40 0.20 25 35 45 55 65 75 85 95 105 115 125 [°C] 13/18 Package mechanical data 9 STCS05A Package mechanical data In order to meet environmental requirements, ST offers these devices in ECOPACK® packages. These packages have a lead-free second level interconnect. The category of second Level Interconnect is marked on the package and on the inner box label, in compliance with JEDEC Standard JESD97. The maximum ratings related to soldering conditions are also marked on the inner box label. ECOPACK is an ST trademark. ECOPACK specifications are available at: www.st.com. 14/18 STCS05A Package mechanical data SO-8 mechanical data Dim. mm. Min. Typ. inch. Max. Min. Typ. Max. A 1.35 1.75 0.053 0.069 A1 0.10 0.25 0.04 0.010 A2 1.10 1.65 0.043 0.065 B 0.33 0.51 0.013 0.020 C 0.19 0.25 0.007 0.010 D 4.80 5.00 0.189 0.197 E 3.80 4.00 0.150 0.157 e 1.27 0.050 H 5.80 6.20 0.228 0.244 h 0.25 0.50 0.010 0.020 L 0.40 1.27 0.016 0.050 k ddd 8° (max.) 0.1 0.04 0016023/C 15/18 Package mechanical data STCS05A Tape & reel SO-8 mechanical data mm. inch. Dim. Min. A Max. Min. 330 13.2 Typ. Max. 12.992 C 12.8 D 20.2 0.795 N 60 2.362 T 16/18 Typ. 0.504 22.4 0.519 0.882 Ao 8.1 8.5 0.319 0.335 Bo 5.5 5.9 0.216 0.232 Ko 2.1 2.3 0.082 0.090 Po 3.9 4.1 0.153 0.161 P 7.9 8.1 0.311 0.319 STCS05A Revision history 10 Revision history Table 6. Document revision history Date Revision Changes 04-Mar-2008 1 Initial release. 02-Jul-2008 2 Modified: Table 5 on page 6. 17/18 STCS05A Please Read Carefully: Information in this document is provided solely in connection with ST products. STMicroelectronics NV and its subsidiaries (“ST”) reserve the right to make changes, corrections, modifications or improvements, to this document, and the products and services described herein at any time, without notice. All ST products are sold pursuant to ST’s terms and conditions of sale. Purchasers are solely responsible for the choice, selection and use of the ST products and services described herein, and ST assumes no liability whatsoever relating to the choice, selection or use of the ST products and services described herein. No license, express or implied, by estoppel or otherwise, to any intellectual property rights is granted under this document. If any part of this document refers to any third party products or services it shall not be deemed a license grant by ST for the use of such third party products or services, or any intellectual property contained therein or considered as a warranty covering the use in any manner whatsoever of such third party products or services or any intellectual property contained therein. UNLESS OTHERWISE SET FORTH IN ST’S TERMS AND CONDITIONS OF SALE ST DISCLAIMS ANY EXPRESS OR IMPLIED WARRANTY WITH RESPECT TO THE USE AND/OR SALE OF ST PRODUCTS INCLUDING WITHOUT LIMITATION IMPLIED WARRANTIES OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE (AND THEIR EQUIVALENTS UNDER THE LAWS OF ANY JURISDICTION), OR INFRINGEMENT OF ANY PATENT, COPYRIGHT OR OTHER INTELLECTUAL PROPERTY RIGHT. UNLESS EXPRESSLY APPROVED IN WRITING BY AN AUTHORIZED ST REPRESENTATIVE, ST PRODUCTS ARE NOT RECOMMENDED, AUTHORIZED OR WARRANTED FOR USE IN MILITARY, AIR CRAFT, SPACE, LIFE SAVING, OR LIFE SUSTAINING APPLICATIONS, NOR IN PRODUCTS OR SYSTEMS WHERE FAILURE OR MALFUNCTION MAY RESULT IN PERSONAL INJURY, DEATH, OR SEVERE PROPERTY OR ENVIRONMENTAL DAMAGE. ST PRODUCTS WHICH ARE NOT SPECIFIED AS "AUTOMOTIVE GRADE" MAY ONLY BE USED IN AUTOMOTIVE APPLICATIONS AT USER’S OWN RISK. Resale of ST products with provisions different from the statements and/or technical features set forth in this document shall immediately void any warranty granted by ST for the ST product or service described herein and shall not create or extend in any manner whatsoever, any liability of ST. ST and the ST logo are trademarks or registered trademarks of ST in various countries. Information in this document supersedes and replaces all information previously supplied. The ST logo is a registered trademark of STMicroelectronics. All other names are the property of their respective owners. © 2008 STMicroelectronics - All rights reserved STMicroelectronics group of companies Australia - Belgium - Brazil - Canada - China - Czech Republic - Finland - France - Germany - Hong Kong - India - Israel - Italy - Japan Malaysia - Malta - Morocco - Singapore - Spain - Sweden - Switzerland - United Kingdom - United States of America www.st.com 18/18