STG3693 Low voltage high bandwidth Quad SPDT switch Features ■ Ultra low power dissipation: – ICC = 0.2µA (Max.) at TA = 85°C ■ Low “ON” resistance: – RON = 4Ω (TA = 25°C) at VCC = 3.0V ■ Wide operating voltage range: – VCC (Opr) = 1.65V to 4.3V single supply QFN16L (2.6mm x 1.8mm) ■ 4.3V tolerant and 1.8V compatible threshold on digital control input at VCC = 2.3V to 3.0V ■ Typical bandwidth (-3dB) at 800MHz on all channels ■ Latch-up performance exceeds 100mA per JESD 78, Class II ■ ESD performance exceeds JESD22 – 2000-V Human body model (A114-A) ■ USB (2.0) high speed (480Mbps) signal switching compliant Description The STG3693 is a high-speed CMOS low voltage quad analog S.P.D.T. (Single Pole Dual Throw) Switch or 2:1 Multiplexer /Demultiplexer Switch fabricated in silicon gate C2MOS technology. It is designed to operate from 1.65V to 4.3V, making this device ideal for portable applications. The nSEL inputs are provided to control the switch. The switch S1 is ON (they are connected to common Ports Dn) when the nSEL input is held high and OFF (high impedance state exists between the two ports) when SEL is held low; the switch S2 is ON (it is connected to common Port D) when the nSEL input is held low and OFF (high impedance state exists between the two ports) when nSEL is held high. Additional key features are fast switching speed, Break Before Make Delay Time and Ultra Low Power Consumption. All inputs and outputs are equipped with protection circuits against static discharge, giving them ESD immunity and transient excess voltage. Order codes Part number Package Packaging STG3693QTR QFN16L (2.6mm x 1.8mm) Tape and reel January 2007 Rev 1 1/17 www.st.com 17 Contents STG3693 Contents 1 Pin settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 1.1 Pin connection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 1.2 Pin description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 2 Device summary . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 3 Maximum rating . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 3.1 Recommended operating conditions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 4 Electrical characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 5 Test circuits 6 Package mechanical data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12 7 Revision history . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16 2/17 ............................................... 9 STG3693 Pin settings 1 Pin settings 1.1 Pin connection Figure 1. 1.2 Pin connection (top through view) Pin description Table 1. Pin description Note: Pin N° Symbol Name and function 15,1, 4,6, 7,9, 12,14 1S1, 1S2, 2S1, 2S2, 3S1, 3S2, 4S1, 4S2 16,5,8,13 D1, D2, D3, D4 3, 10 1-2-3SEL, 4SEL 2 VCC Possitive supply voltage 11 GND Ground (0V) Independent channels Common channels Control Exposed pad must be soldered to a floating plane. Do NOT connect to power or ground. 3/17 Device summary 2 STG3693 Device summary Figure 2. Input equivalent circuit S2 D S1 SEL Table 2. Truth table 4/17 1-2-3SEL 4SEL SWITCH 1 SWITCH 2 SWITCH 3 SWITCH 4 H X D1-1S1 D2-2S1 D3-3S1 X L X D1-1S2 D2-2S2 D3-3S2 X X H X X X 4D-4S1 X L X X X 4D-4S2 STG3693 3 Maximum rating Maximum rating Stressing the device above the rating listed in the “Absolute Maximum Ratings” table may cause permanent damage to the device. These are stress ratings only and operation of the device at these or any other conditions above those indicated in the Operating sections of this specification is not implied. Exposure to Absolute Maximum Rating conditions for extended periods may affect device reliability. Refer also to the STMicroelectronics SURE Program and other relevant quality documents. Table 3. Absolute maximum ratings Symbol VCC Parameter Supply voltage Value Unit -0.5 to 5.5 V -0.5 to VCC + 0.5 V -0.5 to 5.5 V -0.5 to VCC + 0.5 V VI DC input voltage VIC DC control input voltage VO DC output voltage IIKC DC input diode current on control pin (VSEL<0V) -50 mA IIK DC input diode current (VSEL<0V) ±50 mA IOK DC output diode current ±20 mA IO DC output current ±128 mA IOP DC output current peak (pulse at 1ms, 10% duty cycle) ±300 mA DC VCC or ground current ±100 mA PD Power dissipation at TA = 70°C (1) 1120 mW Tstg Storage temperature -65 to 150 °C 300 °C Value Unit 1.65 to 4.3 V ICC or IGND TL Lead temperature (10 sec) 1. Derate above 70ºC by 18.5mW/C 3.1 Recommended operating conditions Table 4. Recommended operating conditions Symbol VCC Parameter Supply voltage(1) VI Input voltage 0 to VCC V VIC Control input voltage 0 to 4.3 V VO Output voltage 0 to VCC V Top Operating temperature -55 to 125 °C dt/dv Input rise and fall time control input VCC = 1.65V to 2.7V 0 to 20 VCC = 3.0 to 4.3V 0 to 10 ns/V 1. Truth Table guaranteed: 1.2V to 4.3V 5/17 Electrical characteristics 4 STG3693 Electrical characteristics Table 5. DC Specifications Test conditions Symbol Parameter Value TA = 25°C Vcc (V) Min VIH VIL High level input voltage Low level input voltage Switch ON peak resistance RON Switch On resistance ∆RON ON resistance match between channels Max Min 1.65 -1.95 0.65VCC 0.65VCC 2.3-2.5 1.2 1.2 2.7-3.0 1.3 1.3 3.3-3.6 1.4 1.4 4.3 1.6 1.6 1.65-1.95 0.25 2.3-2.5 0.25 2.7-3.0 0.25 3.3-3.6 0.30 4.3 0.40 12.0 16.0 6.3 8.0 5.8 7.5 3.7 5.0 6.5 4.3 4.6 6.0 1.8 RPEAK Typ -40 to 85°C 2.7 3.0 VS = 0V to VCC IS = 8mA 3.0 VS = 3V IS = 8mA 4.0 5.2 3.0 VS = 0.8V IS = 8mA 5.0 6.5 VS @ RON Max IS = 8mA 0.3 Unit Max V V Ω Ω 1.8 2.7 3.0 Ω 3.7 4.3 6.6 1.8 RFLAT IOFF 6/17 ON resistance flatness OFF state leakage current (SN), (D) 2.7 3.0 2.0 VS = 0V to VCC IS = 8mA 3.7 1.5 4.3 1.6 4.3 VS = 0.3 or 4V Ω 1.7 ±20 ±100 nA STG3693 Electrical characteristics Table 5. DC Specifications (continued) Test conditions Symbol Parameter Value TA = 25°C Vcc (V) Min IIN Input leakage current ICC Quiescent supply current ICCLV Quiescent supply current low voltage driving 0 to 4.3 1.65 to 4.3 4.3 -40 to 85°C Typ Max Min Unit Max VSEL = 0 to 4.3V ±0.1 ±1 µA VSEL = VCC or GND ±0.1 ±1.0 µA V1-2-3SEL, V4-SEL = 1.65V ±37 ±50 ±100 V1-2-3SEL, V4-SEL = 1.80V ±33 ±40 ±50 V1-2-3SEL, V4-SEL = 2.60V ±11 ±20 ±30 µA Table 6. AC electrical characteristics (CL = 35pF, RL = 50Ω, tr = tf ≤5ns) Test conditions Symbol Parameter Value TA = 25°C Vcc (V) Min tPLH, tPHL Propagation delay 1.65-1.95 0.30 2.3-2.7 0.30 3.0-3.3 0.25 3.6-4.3 0.25 1.65-1.95 tON TURN-ON time VS = 0.8V 2.3-2.7 3.0-3.3 1.65-1.95 TURN-OFF time VS = 1.5V VS = 0.8 VS = 1.5V 3.6-4.3 1.65-1.95 tD Break before make time delay 2.3-2.7 3.0-3.3 CL = 35pF RL = 50Ω VS = 1.5V 3.6-4.3 Charge injection 2.3 3.0 4.3 Max ns 20 26 34 20 20 26 20 15 20 4 6 8 4 6 8 3 5 6 ns 1 7 1 5 1 4 1 3 ns ns 2.8 1.65 Q Min 5 2.3-2.7 3.0-3.3 Max Unit 31 3.6-4.3 tOFF Typ -40 to 85°C CL = 100pF VGEN = 0V RGEN = 0Ω 3.5 3.8 pC 5.0 7/17 Electrical characteristics STG3693 Table 7. Analog switch characteristics (CL = 5pF, RL = 50Ω, TA = 25°C) Test Conditions Symbol Parameter Value TA = 25°C Vcc (V) Min OIRR Xtalk Off Isolation (1) Crosstalk THD Total harmonic distortion PSRR Power supply rejection ratio Typ -40 to 85°C Max Min Unit Max VS = 1VRMS, f = 1MHz Signal = 0 dBm -79 VS = 1VRMS, f = 10MHz Signal = 0 dBm -60 VS = 1VRMS, f = 1MHz Signal = 0 dBm -78 VS = 1VRMS, f = 10MHz Signal = 0 dBm -61 3.7 f = 20Hz to 20kHz RL = 32Ω, CL=50Ω VIN = 2.8VP-P VDC = VCC/2 0.01 3.7 f = 217Hz, RL = 32Ω, CL = 50Ω Vripple = 150mV VDC = VCC/2 -60 dB RL = 50Ω Signal = 0dBm 800 MHz 1.65 - 4.3 1.65 - 4.3 dB dB 0.02 % BW -3dB Bandwidth 3.0 - 4.3 DG Differential gain 3.0 - 4.3 RL = 150Ω 0.64 % DP Differential phase 3.0 - 4.3 RL = 150Ω 0.1 deg CIN Control pin input capacitance CON Sn Port capacitance when switch is enabled COFF Sn port capacitance when switch is disabled VCC = 0V 6.2 3.3 f = 1MHz 10 3.3 f = 1MHz 21 pF 1. Off Isolation = 20Log10 (VD/VS), VD = output. VS = input to off switch. Table 8. USB related AC electrical characteristics Test conditions Symbol Parameter Value TA = 25°C VCC (V) Min Typ -40 to 85°C Max Min Unit Max tSK(0) Channel-to-channel skew 3.0 to 3.6 CL=10pF 26 ps tSK(P) Skew of opposite transition of the same output 3.0 to 3.6 CL=10pF 60 ps 3.0 to 3.6 RL = 50Ω, CL= 10pF, tR = tF = 750ps at 480Mbps 130 ps TJ 8/17 Total jitter STG3693 Test circuits 5 Test circuits Figure 3. ON-Resistance Figure 4. Bandwidth Figure 5. OFF Leakage Figure 6. Channel to channel crosstalk Figure 7. OFF Isolation 9/17 Test circuits Figure 8. STG3693 Test circuit Note: 1 CL = 5/35pF or equivalent: (includes jig capacitance) 2 RL = 50Ω or equivalent 3 RT = ZOUT of pulse generator (typically 50Ω) Figure 9. Break-before-make time delay Figure 10. Switching time and charge injection (VGEN = 0V, RGEN = 0Ω, RL = 1MΩ, CL = 100pF) 10/17 STG3693 Test circuits Figure 11. Turn ON, turn OFF delay time 11/17 Package mechanical data 6 STG3693 Package mechanical data In order to meet environmental requirements, ST offers these devices in ECOPACK® packages. These packages have a Lead-free second level interconnect . The category of second level interconnect is marked on the package and on the inner box label, in compliance with JEDEC Standard JESD97. The maximum ratings related to soldering conditions are also marked on the inner box label. ECOPACK is an ST trademark. ECOPACK specifications are available at: www.st.com 12/17 STG3693 Package mechanical data Table 9. QFN16L (2.6x1.8mm) mechanical data mm. Dim. Min Typ Max A 0.45 0.50 0.55 A1 0 0.02 0.05 A3 0.127 b 0.15 0.20 0.25 D 2.50 2.60 2.70 D2 1.40 1.50 1.60 E 1.70 1.80 1.90 E2 0.60 0.70 0.80 e L Note: 0.40 0.25 0.30 0.35 1 VFQFPN - Standard for thermally enhanced vey fine pitch quad flat package no leads. 2 The leads size is comprehensive of the thickness of the leads finishing material. 3 Dimensions do not include mold protusion. 4 Package outline exclusive of metal burrs dimensions. 5 Shipping media tape and reel units: 3000 Figure 12. Foot print recommendation 13/17 Package mechanical data Figure 13. Package information 14/17 STG3693 STG3693 Package mechanical data Figure 14. QFN16L (2.6mmx1.8mm) tape & reel 15/17 Revision history 7 STG3693 Revision history Table 10. Revision history 16/17 Date Revision 3-Jan-2006 1 Changes First release STG3693 Please Read Carefully: Information in this document is provided solely in connection with ST products. STMicroelectronics NV and its subsidiaries (“ST”) reserve the right to make changes, corrections, modifications or improvements, to this document, and the products and services described herein at any time, without notice. All ST products are sold pursuant to ST’s terms and conditions of sale. Purchasers are solely responsible for the choice, selection and use of the ST products and services described herein, and ST assumes no liability whatsoever relating to the choice, selection or use of the ST products and services described herein. No license, express or implied, by estoppel or otherwise, to any intellectual property rights is granted under this document. If any part of this document refers to any third party products or services it shall not be deemed a license grant by ST for the use of such third party products or services, or any intellectual property contained therein or considered as a warranty covering the use in any manner whatsoever of such third party products or services or any intellectual property contained therein. UNLESS OTHERWISE SET FORTH IN ST’S TERMS AND CONDITIONS OF SALE ST DISCLAIMS ANY EXPRESS OR IMPLIED WARRANTY WITH RESPECT TO THE USE AND/OR SALE OF ST PRODUCTS INCLUDING WITHOUT LIMITATION IMPLIED WARRANTIES OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE (AND THEIR EQUIVALENTS UNDER THE LAWS OF ANY JURISDICTION), OR INFRINGEMENT OF ANY PATENT, COPYRIGHT OR OTHER INTELLECTUAL PROPERTY RIGHT. UNLESS EXPRESSLY APPROVED IN WRITING BY AN AUTHORIZED ST REPRESENTATIVE, ST PRODUCTS ARE NOT RECOMMENDED, AUTHORIZED OR WARRANTED FOR USE IN MILITARY, AIR CRAFT, SPACE, LIFE SAVING, OR LIFE SUSTAINING APPLICATIONS, NOR IN PRODUCTS OR SYSTEMS WHERE FAILURE OR MALFUNCTION MAY RESULT IN PERSONAL INJURY, DEATH, OR SEVERE PROPERTY OR ENVIRONMENTAL DAMAGE. ST PRODUCTS WHICH ARE NOT SPECIFIED AS "AUTOMOTIVE GRADE" MAY ONLY BE USED IN AUTOMOTIVE APPLICATIONS AT USER’S OWN RISK. Resale of ST products with provisions different from the statements and/or technical features set forth in this document shall immediately void any warranty granted by ST for the ST product or service described herein and shall not create or extend in any manner whatsoever, any liability of ST. ST and the ST logo are trademarks or registered trademarks of ST in various countries. Information in this document supersedes and replaces all information previously supplied. The ST logo is a registered trademark of STMicroelectronics. All other names are the property of their respective owners. © 2007 STMicroelectronics - All rights reserved STMicroelectronics group of companies Australia - Belgium - Brazil - Canada - China - Czech Republic - Finland - France - Germany - Hong Kong - India - Israel - Italy - Japan Malaysia - Malta - Morocco - Singapore - Spain - Sweden - Switzerland - United Kingdom - United States of America www.st.com 17/17