STMICROELECTRONICS TSH122

TSH122
Ultra low power video buffer/filter with power-down
Features
SC70
■
Very low consumption: 1.7 mA
■
Ultra low power-down mode: 4 nA typ.,
500 nA max.
■
Internal 6th order reconstruction filter
■
Internal gain of 6 dB
■
Rail-to-rail output buffer for 75 Ω video line
■
Excellent video performance
– Differential gain 0.5%
– Differential phase 0.10°
– Group delay of 10 ns
■
SAG correction
■
Bottom of video signal close to 0 V
■
Tested with 2.5 V and 3.3 V single supply
■
Data min. and max. are physically tested and
guaranteed during production (consumption,
gain, filtering, and other parameters are
guaranteed)
Applications
■
Mobile phones
■
Digital still camera
■
Digital video camera
■
Portable DVD players
Top view
IN 1
6
Vcc
GND 2
5
EN (enable)
SAG 3
4
OUT
Description
The TSH122 is a video buffer that uses a voltage
feedback amplifier, with an internal gain of 6 dB,
an output rail-to-rail, an internal input DC-shift and
a SAG correction. A power-down function allows
switching to a sleep mode with an ultra-low
consumption.
The TSH122 features a 6th-order internal
reconstruction filter to attenuate the parasitic
frequency of 27 MHz from the clock of the video
DAC.
The TSH122 operates from 2.25 to 5 V single
power supplies and is tested at 2.5 V and 3.3 V.
The TSH122 is a single operator available in a
tiny SC70 plastic package for space saving.
August 2008
Rev 1
1/16
www.st.com
16
Absolute maximum ratings and operating conditions
1
TSH122
Absolute maximum ratings and operating conditions
Table 1.
Absolute maximum ratings
Symbol
Value
Unit
5.5
V
0 to Vcc
V
-65 to +150
°C
Maximum junction temperature
150
°C
Rthja
SC70 thermal resistance junction to ambient area
205
°C/W
Rthjc
SC70 thermal resistance junction to case
172
°C/W
Pmax
Maximum power dissipation for Tj=150°C
Tamb = +25°C
Tamb = +85°C
609
317
mW
ESD
CDM: charged device model(2)
HBM: human body model(3)
MM: machine model(4)
1.5
1.5
300
kV
kV
V
VCC
Vin
Tstg
Tj
Parameter
Supply voltage(1)
Maximum input amplitude
Storage temperature
(5)
Output short-circuit
1. All voltage values, except differential voltage, are with respect to network terminal.
2. Charged device model: all pins and the package are charged together to the specified voltage and then
discharged directly to the ground through only one pin. This is done for all pins.
3. Human body model: a 100 pF capacitor is charged to the specified voltage, then discharged through a
1.5 kΩ resistor between two pins of the device. This is done for all couples of connected pin combinations
while the other pins are floating.
4. Machine model: a 200 pF capacitor is charged to the specified voltage, then discharged directly between
two pins of the device with no external series resistor (internal resistor < 5 Ω). This is done for all couples of
connected pin combinations while the other pins are floating
5. An output current limitation protects the circuit from transient currents. Short-circuits can cause excessive
heating. Destructive dissipation can result from short-circuits on amplifiers.
Table 2.
Operating conditions
Symbol
Parameter
Unit
VCC
Power supply voltage
2.25 to 5 (1)
V
Toper
Operating free air temperature range
-40 to +85
°C
1. Tested in full production at 0 V/2.5 V and 0 V/3.3 V single power supply.
2/16
Value
TSH122
Electrical characteristics
2
Electrical characteristics
Table 3.
VCC = +2.5V, +3.3V, Tamb = 25°C (unless otherwise specified)
Symbol
Parameter
Test conditions
Min.
Typ.
Max.
Unit
RL = 150Ω
70
115
168
mV
VCC = +3.3V
-1.5
-0.87
DC performance
Vdc
Iib
G
Output DC level shift
Input bias current
Internal voltage gain
VCC = +3.3V,
Tmin ≤ Tamb ≤ Tmax
Vin=0V to 1V DC, VCC=+2.5V
5.8
6
6.1
Vin=0V to 1.4V DC, VCC=+3.3V
5.8
6
6.1
VCC=3.3V
Tmin ≤ Tamb ≤ Tmax
PSRR
ICC
Power supply rejection ratio
20 log (ΔVCC/ΔVout)
Positive supply current
DC consumption
μA
-0.93
dB
5.96
ΔVCC=±100mV at 1kHz
Vin=+0.5V DC
55
Vin=0V, no load
VCC=+3.3V
VCC=+2.5V
2
1.7
VCC=+3.3V
Tmin ≤ Tamb ≤ Tmax
dB
2.4
2.1
mA
2.4
mA
9.5
7.2
MHz
Dynamic performance and output characteristics
BW
Filter bandwidth
Small signal
VCC=+3.3V, RL = 150Ω
-3dB bandwidth
-1dB bandwidth
5.4
-1dB bandwidth
VCC = +3.3V,
Tmin ≤ Tamb ≤ Tmax
FR
27 MHz rejection
Small signal
VCC=+3.3V, RL=150Ω
6.75
36
47
dB
VCC = +3.3V,
Tmin ≤ Tamb ≤ Tmax
46
dB
ΔG
Differential gain
VCC=+3.3V, RL=150Ω
0.5
%
ΔΦ
Differential phase
VCC=+3.3V, RL=150Ω
0.1
°
Gd
Group delay
VCC=+3.3V, 10kHz-5MHz
6
ns
VOH
High level output voltage
VCC=+3.3V, RL=150Ω
VCC=+2.5V, RL=150Ω
3.2
2.4
V
3.1
2.3
3/16
Electrical characteristics
Table 3.
TSH122
VCC = +2.5V, +3.3V, Tamb = 25°C (unless otherwise specified) (continued)
Symbol
Parameter
Test conditions
Min.
Typ.
Max.
Unit
40
mV
VOL
Low level output voltage
RL = 150Ω
11
Iout
Output short circuit current
VCC=+2.5V
75
mA
Total output noise
F = 100kHz, no load
51
nV/√Hz
Harmonic distortion
VCC=+3.3V, RL = 150Ω
Vin=1Vp-p, F=1MHz
H2
H3
64
61
VCC=+3.3V
4
Noise and distortion
eN
HD
dBc
Enable/power-down
Low level on pin-5: TSH122 in power-down
High level on pin-5: TSH122 enabled
Isd
Consumption in power-down
mode
500
nA
Vlow
Low-level threshold
0
+0.3
V
Vhigh
High-level threshold
+0.7
VCC
V
Ton
Time from power-down to enable
1
μs
Toff
Time from enable to power-down
1
μs
4/16
TSH122
Electrical characteristics
Figure 1.
Frequency response
Figure 2.
10
6.2
0
6.1
Flatness (dB)
Gain (dB)
Vcc=+3.3V
5.9
-20
-30
-40
-50
-70
Vcc=+2.5V
6.0
-10
-60
Gain flatness
5.8
5.7
5.6
Vcc=+5V
5.5
Vcc=3.3V
Load=150Ω
Small signal
Vicm=0.5V
5.4
5.3
-80
1M
10M
5.2
1M
100M
10M
Frequency (Hz)
Figure 3.
Frequency (Hz)
Input noise
Figure 4.
250
Vcc=+5V
Load=150Ω
No load
Input to GND
Vcc=+2.5V and +3.3V
200
4
150
Vout (V)
en (nV/VHz)
Distortion
5
100
50
Vcc=+3.3V
3
Vcc=+2.5V
2
1
0
100
1k
10k
100k
0
0.0
1M
0.5
1.0
Frequency (Hz)
Figure 5.
Distortion at Vcc=2.5 V
Figure 6.
-30
-40
-40
Distortion (dB)
Distortion (dB)
H2
Distortion at Vcc=3.3 V
Vcc=3.3V
Load=150Ω
-60
-70
H2
-80
H3
-90
-100
0.0
2.5
-50
-60
-80
2.0
-30
Vcc=2.5V
Load=150Ω
-50
-70
1.5
Vin (V)
H3
-90
0.5
1.0
1.5
Output Amplitude (Vp-p)
2.0
2.5
-100
0.0
0.5
1.0
1.5
2.0
2.5
3.0
Output Amplitude (Vp-p)
5/16
Electrical characteristics
DCshift vs. Vcc
Figure 8.
125
10
124
9
123
8
122
7
VOL (mV)
Output DCshift (mV)
Figure 7.
TSH122
121
120
119
6
5
4
118
3
117
2
Load=150Ω
116
115
2.0
VOL vs. Vcc
Vin= -100mV
Load=150Ω
1
0
2.5
3.0
3.5
4.0
4.5
5.0
2
3
Vcc (V)
Figure 9.
4
5
Vcc (V)
Icc vs. Vcc
Figure 10. Power down
2.00
4.0
3.5
1.75
3.0
Isd (nA)
Icc (mA)
1.50
2.5
2.0
1.25
1.5
1.00
1.0
0.75
0.5
0.0
0
1
2
3
4
5
6
0.50
2.0
2.5
Vcc (V)
Figure 11. Switch-on output settling
3.0
3.5
EN (pin5)
Vout (pin4)
Vout (pin4)
6/16
4.5
Figure 12. Switch-off output settling
EN (pin5)
Vcc=+3.3V, Vin=+1.3Vdc
4.0
Vcc (V)
Vcc=+3.3V, Vin=+1.3Vdc
5.0
5.5
TSH122
Electrical characteristics
Figure 13. In/Out switch on/off
Figure 14. Synchronization tip at 0 V
Vin
Vin
Vout
Vout
EN (pin5)
Vcc=+3.3V
Vcc=+3.3V
Figure 15. VOL vs. temperature
Figure 16. VOH vs. temperature
5.0
20.0
Load=150Ω
17.5
4.5
15.0
VOH (mV)
VOL (mV)
4.0
Vcc=+2.5V
12.5
10.0
Vcc=+3.3V
7.5
3.5
3.0
Vcc=+3.3V
5.0
2.5
2.5
Load=150Ω
0.0
-40
-20
Vcc=+2.5V
0
20
40
60
2.0
-40
80
-20
Temperature (°C)
60
80
-40.0
8.5
-42.5
Attenuation@27MHz (dB)
Vcc=+2.5V
8.0
Bw@-1dB (MHz)
40
Figure 18. Attenuation vs. temperature
9.0
7.5
7.0
Vcc=+3.3V
6.5
6.0
5.5
5.0
4.0
-40
20
Temperature (°C)
Figure 17. Bandwidth vs. temperature
4.5
0
-47.5
Vcc=+3.3V
-50.0
-52.5
-55.0
-57.5
Small signal
Load=150Ω
-20
Vcc=+2.5V
-45.0
Load=150Ω
0
20
40
Temperature (°C)
60
80
-60.0
-40
-20
0
20
40
60
80
Temperature (°C)
7/16
Electrical characteristics
TSH122
Figure 19. Icc vs. temperature
Figure 20. Gain vs. temperature
3.0
6.10
2.5
Vcc=+3.3V
6.05
Gain (dB)
ICC (mA)
2.0
Vcc=+2.5V
1.5
Vcc=+3.3V
6.00
1.0
Vcc=+2.5V
5.95
0.5
no Load
0.0
-40
-20
Load=150Ω
0
20
40
60
5.90
-40
80
-20
Temperature (°C)
20
40
60
80
60
80
Temperature (°C)
Figure 21. Output DC shift vs. temperature
Figure 22. Ibias vs. temperature
0.00
200
180
0
Vcc=+2.5V and +3.3V
Load=150Ω
-0.25
-0.50
140
Vcc=+2.5V
-0.75
120
IBIAS (μA)
Output DCshift (mV)
160
100
80
-1.00
Vcc=+3.3V
-1.25
60
-1.50
40
-1.75
20
0
-40
Load=150Ω
-20
0
20
40
Temperature (°C)
8/16
60
80
-2.00
-40
-20
0
20
40
Temperature (°C)
TSH122
Application information
3
Application information
3.1
Power supply considerations
Correct power supply bypassing is very important for optimizing performance in
high-frequency ranges. The bypass capacitors should be placed as close as possible to the
IC pins to improve high-frequency bypassing. A capacitor greater than 10 µF is necessary to
minimize the distortion. For better quality bypassing, we recommend adding a 10 nF
capacitor, also placed as close as possible to the IC pins.
Figure 23. Circuit for power supply bypassing
6##
M&
N&
43(
Figure 24. Supply noise rejection
10
Noise supply rejection (dB)
0
Vcc=5V(dc)+0.2Vp-p(ac)
Load=150Ω
Bypass capacitors: 10µF+10nF
-10
-20
-30
-40
-50
-60
-70
-80
10k
100k
1M
10M
100M
Frequency (Hz)
9/16
Application information
TSH122
3.2
Implementation considerations
3.2.1
Input
The DC level shifter optimizes the position of the video signal with no clamping on the output
rails.
3.2.2
Filter
A reconstruction filter is used to attenuate the DAC’s sampling frequency because it
generates a parasitic signal in the video spectrum (typically at 27 MHz in the case of
standard video). This function is fulfilled while keeping a low group delay and a good gain
flatness along the video band.
Figure 25. Internal schematic
2.25 V to 5 V
+Vcc
6
DC shifter
Input
1
LPF
6th
5 Power-down
+
+
4
order
-
2R
2R
R
2R
2
3.2.3
Output
3
SAG
GND
Output
In an AC-coupling configuration, the SAG correction allows use of two small low-cost
capacitors in place of one large capacitor (see Figure 26). The AC-coupling output reduces
the power consumption by removing the DC component included in the signal.
Nevertheless, the output can be directly connected to the line without any capacitor. In this
case, the OUT and SAG pins are connected together and the equivalent gain of the buffer
remains at 6 dB (see Figure 27).
10/16
TSH122
Application information
Figure 26. Schematic diagram with output capacitor
6TO6
46
0OWERDOWN
6IDEO
$!#
—&
7
7 CABLE
$!#S
LOAD
7
3!'
—&
%QUIVALENTTOASINGLE
!#COUPLINGOUTPUTWITH
ABIGCAPACITOROF—&
—&
7
7 CABLE
7
Figure 27. Schematic diagram without output capacitor
6TO6
46
0OWERDOWN
7
6IDEO
$!#
7 CABLE
$!#S
LOAD
7
3!'
11/16
Application information
3.3
TSH122
Using the TSH122 to drive a Cvbs signal
Figure 28. Details on Cvbs (NTSC color bar 100%)
DAC output amplitude
+133 IRE
+100 IRE
0 IRE
~1.3 V
White
Blanking
level
Burst
Synchronization tip
-40 IRE
GND
With its internal DC shift, the TSH122 can drive a video signal from the DAC output as low
as 0 V (bottom of the synchronization tip at 0 V - see Figure 14).
12/16
TSH122
4
Package information
Package information
In order to meet environmental requirements, STMicroelectronics offers these devices in
ECOPACK® packages. These packages have a lead-free second level interconnect. The
category of second level interconnect is marked on the package and on the inner box label,
in compliance with JEDEC Standard JESD97. The maximum ratings related to soldering
conditions are also marked on the inner box label. ECOPACK is an STMicroelectronics
trademark. ECOPACK specifications are available at: www.st.com.
Figure 29. SC70-6 (or SOT323-6) package footprint (in millimeters)
0.65
1.05
0.80
2.90
0.40
13/16
Package information
TSH122
Figure 30. SC70-6 (or SOT323-6) package mechanical data
Dimensions
Ref
Millimeters
Min
Typ
Mils
Max
Min
Typ
Max
A
0.80
1.10
31.5
43.3
A1
0
0.10
0
3.9
A2
0.80
1.00
31.5
39.3
b
0.15
0.30
5.9
11.8
c
0.10
0.18
3.9
7.0
D
1.80
2.20
70.8
86.6
E
1.15
1.35
45.2
43.1
e
0.65
25.6
2.4
70.8
94.5
L
0.10
0.40
3.9
15.7
Q1
0.10
0.40
3.9
15.7
D
A1
E
HE
L
b
Q1
C
14/16
e
e
A
1.8
A2
HE
TSH122
5
Ordering information
Ordering information
Table 4.
6
Order codes
Part number
Temperature range
Package
Packaging
Marking
TSH122ICT
-40°C to +85°C
SC70
Tape & reel
K31
Revision history
Table 5.
Document revision history
Date
Revision
04-Aug-2008
1
Changes
Initial release.
15/16
TSH122
Please Read Carefully:
Information in this document is provided solely in connection with ST products. STMicroelectronics NV and its subsidiaries (“ST”) reserve the
right to make changes, corrections, modifications or improvements, to this document, and the products and services described herein at any
time, without notice.
All ST products are sold pursuant to ST’s terms and conditions of sale.
Purchasers are solely responsible for the choice, selection and use of the ST products and services described herein, and ST assumes no
liability whatsoever relating to the choice, selection or use of the ST products and services described herein.
No license, express or implied, by estoppel or otherwise, to any intellectual property rights is granted under this document. If any part of this
document refers to any third party products or services it shall not be deemed a license grant by ST for the use of such third party products
or services, or any intellectual property contained therein or considered as a warranty covering the use in any manner whatsoever of such
third party products or services or any intellectual property contained therein.
UNLESS OTHERWISE SET FORTH IN ST’S TERMS AND CONDITIONS OF SALE ST DISCLAIMS ANY EXPRESS OR IMPLIED
WARRANTY WITH RESPECT TO THE USE AND/OR SALE OF ST PRODUCTS INCLUDING WITHOUT LIMITATION IMPLIED
WARRANTIES OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE (AND THEIR EQUIVALENTS UNDER THE LAWS
OF ANY JURISDICTION), OR INFRINGEMENT OF ANY PATENT, COPYRIGHT OR OTHER INTELLECTUAL PROPERTY RIGHT.
UNLESS EXPRESSLY APPROVED IN WRITING BY AN AUTHORIZED ST REPRESENTATIVE, ST PRODUCTS ARE NOT
RECOMMENDED, AUTHORIZED OR WARRANTED FOR USE IN MILITARY, AIR CRAFT, SPACE, LIFE SAVING, OR LIFE SUSTAINING
APPLICATIONS, NOR IN PRODUCTS OR SYSTEMS WHERE FAILURE OR MALFUNCTION MAY RESULT IN PERSONAL INJURY,
DEATH, OR SEVERE PROPERTY OR ENVIRONMENTAL DAMAGE. ST PRODUCTS WHICH ARE NOT SPECIFIED AS "AUTOMOTIVE
GRADE" MAY ONLY BE USED IN AUTOMOTIVE APPLICATIONS AT USER’S OWN RISK.
Resale of ST products with provisions different from the statements and/or technical features set forth in this document shall immediately void
any warranty granted by ST for the ST product or service described herein and shall not create or extend in any manner whatsoever, any
liability of ST.
ST and the ST logo are trademarks or registered trademarks of ST in various countries.
Information in this document supersedes and replaces all information previously supplied.
The ST logo is a registered trademark of STMicroelectronics. All other names are the property of their respective owners.
© 2008 STMicroelectronics - All rights reserved
STMicroelectronics group of companies
Australia - Belgium - Brazil - Canada - China - Czech Republic - Finland - France - Germany - Hong Kong - India - Israel - Italy - Japan Malaysia - Malta - Morocco - Singapore - Spain - Sweden - Switzerland - United Kingdom - United States of America
www.st.com
16/16