MBR1030CT THRU MBR10200CT 10.0 AMPS. Schottky Barrier Rectifiers Voltage Range 30 to 200 Volts Current 10.0 Amperes TO-220 Features Plastic material used carries Underwriters Laboratory Classifications 94V-0 Metal silicon junction, majority carrier conduction Low power loss, high efficiency High current capability, low forward voltage drop High surge capability For use in low voltage, high frequency inverters, free wheeling, and polarity protection applications Guardring for overvoltage protection High temperature soldering guaranteed: 260oC/10 seconds,0.25”(6.35mm)from case Mechanical Data Cases: JEDEC TO-220A molded plastic body Terminals: Lead solderable per MIL-STD-750, Method 2026 Polarity: As marked Mounting position: Any Mounting torque: 5 in. - lbs. max Weight: 0.08 ounce, 2.24 grams Dimensions in inches and (millimeters) Maximum Ratings and Electrical Characteristics Rating at 25℃ambient temperature unless otherwise specified. Single phase, half wave, 60 Hz, resistive or inductive load. For capacitive load, derate current by 20% Type Number Maximum Recurrent Peak Reverse Voltage Maximum RMS Voltage Maximum DC Blocking Voltage Maximum Average Forward Rectified Current at Tc=125OC Peak Repetitive Forward Current (Rated VR, Square Wave, 20KHz) at Tc=125oC Peak Forward Surge Current, 8.3 ms Single Half Sine-wave Superimposed on Rated Load (JEDEC method ) Peak Repetitive Reverse Surge Current (Note 1) Maximum Instantaneous Forward Voltage at: o (Note 2) IF=5A, TC=25 C o IF=5A, TC=125 C Maximum Instantaneous Reverse Current @ Tc =25℃ at Rated DC Blocking Voltage (Note 2) Voltage Rate of Change (Rated VR) Maximum Typical Thermal Resistance (Note 3) Operating Junction Temperature Range Symbol VRRM VRMS VDC MBR MBR MBR MBR MBR MBR MBR MBR MBR 1030 1035 1040 1045 1050 1060 1010 1015 1020 CT CT CT CT CT CT 0CT 0CT 0CT 30 21 30 35 24 35 40 28 40 45 31 45 50 35 50 60 42 60 100 150 200 70 105 140 100 150 200 Units V V V I(AV) 10 A IFRM 32 A IFSM 120 A IRRM 0.5 A VF 0.80 0.65 0.70 0.57 0.1 IR 0.85 0.88 0.99 0.75 0.78 0.87 0.8 0.2 V mA dV/dt RθJC 10,000 1.5 V/uS ℃/W TJ -65 to +150 ℃ Storage Temperature Range ℃ TSTG -65 to +175 Notes: 1. 2.0us Pulse Width, f=1.0 KHz 2. Pulse Test: 300us Pulse Width, 1% Duty Cycle 3. Thermal Resistance from Junction to Case Per Leg, Mount on Heatsink Size of 2 in x 3 in x 0.25in Al-Plate. - 128 - RATINGS AND CHARACTERISTIC CURVES (MBR1030CT THRU MBR10200CT) FIG.2- MAXIMUM NON-REPETITIVE FORWARD SURGE CURRENT FIG.1- FORWARD CURRENT DERATING CURVE 180 RESISTIVE OR INDUCTIVE LOAD PEAK FORWARD SURGE CURRENT. (A) AVERAGE FORWARD CURRENT. (A) 6 5 4 3 2 1 Tj=Tj max. 8.3ms Single Half Sine-Wave JEDEC Method 150 120 90 60 30 0 0 0 50 100 o CASE TEMPERATURE. ( C) 0.1 150 1 10 100 NUMBER OF CYCLES AT 60Hz FIG.4- TYPICAL REVERSE CHARACTERISTICS FIG.3- TYPICAL INSTANTANEOUS FORWARD CHARACTERISTICS 50 40 Tj=25 0C 10 MBR1030CT-MBR1045CT INSTANTANEOUS REVERSE CURRENT. (mA) INSTANTANEOUS FORWARD CURRENT. (A) MBR1050CT-MBR1060CT 10 MBR10100CT 1 MBR10150CT 0.1 Tj=125 0C 1 Tj=75 0C 0.1 0.01 MBR10200CT Tj=25 0C Pulse Width=300 s 1% Duty Cycle 0.01 0 0.001 0 0.1 0.2 0.3 0.5 0.6 0.7 0.8 0.9 1.0 1.1 1.2 FORWARD VOLTAGE. (V) 0.4 60 80 100 120 140 100 TRANSIENT THERMAL IMPEDANCE. ( OC/W) 5,000 JUNCTION CAPACITANCE.(pF) 40 FIG.6- TYPICAL TRANSIENT THERMAL CHARACTERISTICS PER LEG FIG.5- TYPICAL JUNCTION CAPACITANCE Tj=25 0C f=1.0MHz Vsig=50mVp-p 1,000 500 100 0.1 20 PERCENT OF RATED PEAK REVERSE VOLTAGE. (%) 1.0 10 100 REVERSE VOLTAGE. (V) 10.0 1 0.1 0.01 0.1 1 T, PULSE DURATION. (sec) - 129 - 10 100