MBRS10H100CT - MBRS10H200CT Pb RoHS 10.0 AMPS. Surface Mount Schottky Barrier Rectifiers Switchmode Power Rectifiers COMPLIANCE D2PAK Features Plastic material used carries Underwriters Laboratory Classifications 94V-0 Metal silicon junction, majority carrier conduction Low power loss, high efficiency High current capability, low forward voltage drop High surge capability For use in low voltage, high frequency inverters, free wheeling, and polarity protection applications Guardring for overvoltage protection High temperature soldering guaranteed: o 260 C/10 seconds,0.25”(6.35mm)from case Mechanical Data Cases: D2PAK molded plastic Terminals: Pure tin plated, lead free. solderable per MIL-STD-750, Method 2026 Polarity: As marked Mounting position: Any Mounting torque: 5 in. - lbs. max Weight: 0.08 ounce, 2.24 grams Dimensions in inches and (millimeters) Maximum Ratings and Electrical Characteristics o Rating at 25 C ambient temperature unless otherwise specified. Single phase, half wave, 60 Hz, resistive or inductive load. For capacitive load, derate current by 20% MBRS MBRS MBRS Type Number Units Symbol 10H100CT 10H150CT 10H200CT Maximum Recurrent Peak Reverse Voltage VRRM 100 150 200 V Maximum RMS Voltage VRMS 70 105 140 V Maximum DC Blocking Voltage VDC 100 150 200 V Maximum Average Forward Rectified Current at o TC=133 C Peak Repetitive Forward Current (Rated VR, Square o Wave, 20KHz) at Tc=133 C Peak Forward Surge Current, 8.3 ms Single Half Sine-wave Superimposed on Rated Load (JEDEC method ) Peak Repetitive Reverse Surge Current (Note 1) Maximum Instantaneous Forward Voltage at (Note 2) o IF= 5A, Tc=25 C o IF= 5A, Tc=125 C o IF=10A, Tc=25 C o IF=10A, Tc=125 C Maximum Instantaneous Reverse Current o at Rated DC Blocking Voltage @Tc=25 C o @ Tc=125 C Voltage Rate of Change, (Rated VR) RMS Isolation Voltage (t=1.0 second, R.H. ≦30%, o (Note 4) TA=25 C) (Note 5) (Note 6) Typical Thermal Resistance Per Leg (Note3) I(AV) 10 A IFRM 10 A IFSM 120 A IRRM VF 1.0 0.5 0.85 0.75 0.95 0.85 0.88 0.75 0.97 0.85 IR 5.0 1.0 dV/dt 10,000 VISO RθJC A V uA mA V/uS 4500 3500 1500 3.5 V o C/W o Operating Junction Temperature Range TJ -65 to +175 C o Storage Temperature Range TSTG -65 to +175 C Notes: 1. 2.0 us Pulse Width, f=1.0 KHz 2. Pulse Test: 300us Pulse Width, 1% Duty Cycle 3. Thermal Resistance from Junction to Case Per Leg. 4. Clip Mounting (on case), where lead does not overlap heatsink with 0.110” offset. 5. Clip mounting (on case), where leads do overlap heatsink. 6. Screw mounting with 4-40 screw, where washer diameter is ≦4.9 mm (0.19”) Version: A07 RATINGS AND CHARACTERISTIC CURVES (MBRS10H100CT - MBRS10H200CT) FIG.1- FORWARD CURRENT DERATING CURVE FIG.2- MAXIMUM NON-REPETITIVE FORWARD SURGE CURRENT 180 RESISTIVE OR INDUCTIVE LOAD PEAK FORWARD SURGE CURRENT. (A) AVERAGE FORWARD CURRENT. (A) 6 5 4 3 2 1 0 0 25 120 90 60 30 0 50 75 125 100 o CASE TEMPERATURE. ( C) 150 175 0.1 1 10 100 NUMBER OF CYCLES AT 60Hz FIG.3- TYPICAL INSTANTANEOUS FORWARD CHARACTERISTICS FIG.4- TYPICAL REVERSE CHARACTERISTICS 5 1 40 Tj=125 0C INSTANTANEOUS REVERSE CURRENT. (mA) INSTANTANEOUS FORWARD CURRENT. (A) Tj=Tj max. 8.3ms Single Half Sine-Wave JEDEC Method 150 20 10 Tj=25 0C 4 2 1 Tj=125 0C 0.1 Tj=75 0C 0.01 0.001 0.4 Tj=25 0C 0 Tj=25 C PULSE WIDTH-300 S 1% DUTY CYCLE 0.2 0.1 0.6 0.7 0.8 1.1 0.9 1.0 FORWARD VOLTAGE. (V) 1.2 0.0001 0 60 80 100 120 140 FIG.6- TYPICAL TRANSIENT THERMAL CHARACTERISTICS PER LEG 100 TRANSIENT THERMAL IMPEDANCE. ( OC/W) 5,000 JUNCTION CAPACITANCE.(pF) 40 PERCENT OF RATED PEAK REVERSE VOLTAGE. (%) FIG.5- TYPICAL JUNCTION CAPACITANCE Tj=25 0C f=1.0MHz Vsig=50mVp-p 1,000 500 100 0.1 20 1.3 1 10 REVERSE VOLTAGE. (V) 100 10 1 0.1 0.01 0.1 1 10 T, PULSE DURATION. (sec) Version: A07 100