PJ7800 Series 3-Terminal Fixed Voltage Positive Regulators T hese voltage regulators are monolithic integrated With adequate heatsinking they can deliver output circuits designed as fixed-voltage regulators for a currents up to 1 ampere. wide variety of applications including local, on-card Although designed primarily as a fixed voltage regulation. These regulators employ internal current regulator, these devices can be used with external limiting, thermal shutdown, and safe-area components to obtain adjustable voltages and currents. compensation. PIN ARRANGEMENT FEATURES • Output Current up to 1 Ampere • No External Components Required • Internal Thermal Overload Protection • Internal Short-Circuit Current Limiting • Output Transistor Safe-Area Compensation • Output Voltage Offered in 4% Tolerance TO-220 TO-220F Pin: 1.Input 2.Ground 3.Output (Heatsink surface connected to Pin 2.) CIRCUIT SCHEMATIC Standard Application Representative Schematic Diagram TYPICAL CONNECTING CIRCUIT A common ground is required between the input and the output voltages. The input voltage must remain typically 2.0V above the output voltage even during the low point on the Input ripple voltage. XX = these two digits of the type number indicate voltage. * = Cin is required if regulator is located an appreciable distance from power supply filter. ** = Co is not needed for stability; however, it does improve transient response. 1-9 2002/01.rev.A PJ7800 Series 3-Terminal Fixed Voltage Positive Regulators • ABSOLUTE MAXIMUM RATINGS (Ta=25℃) RATING SYMBOL PJ7800 Series UNIT Input Voltage Vin * 35 V Input Voltage Vin ** 40 V TO-220 Without heatsink 2 TO-220 Pt *** 15 TO-220F With 10 Power Dissipation ℃/ W heatsink Operating Ambient Temperature Topr -20 to +85 ℃ Operating Junction Temperature Tj 0 to +125 ℃ Tstg -25 to +150 ℃ Storage Temperature Note: * PJ7805 to PJ7818 ** PJ7824 *** Follow the derating curve • ORDERING INFORMATION DEVICE OPERATING TEMPERATURE PACKAGE (AMBIENT) PJ78xxCZ PJ78xxCI • TO-220 TO-220F -20℃ to +85℃ PJ7805 ELECTRICAL CHARACTERISTICS (Vin=10V, Iout=500mA, 0℃≤Tj≤125℃, Cin=0.33μF, Cout=0.1μF; unless otherwise specified.) CHARACTERISTICS Output Voltage SYMBOL Vout TEST CONDITIONS Tj=25℃ 7V≤Vin≤20V, 5mA≤Iout≤1.5A, PD≤15W REGline 7.5V≤Vin≤25V 8V≤Vin≤12V Tj=25℃ 5mA≤Iout≤1.5A 250mA≤Iout≤750mA Iout=0, Tj=25℃ 7V≤Vin≤25V 5mA≤Iout≤1.5A 10Hz≤f≤100KHz, Tj=25℃ f=120Hz, 8V≤Vin≤18V Iout=1.0A, Tj=25℃ f=1KHz Tj=25℃ Tj=25℃ Iout=5mA, 0℃≤Tj≤125℃ TYP. 5 MAX. 5.20 4.75 5 5.25 --------62 ------ 3 1 15 5 4.2 --40 78 2 17 750 2.2 -0.6 100 50 100 50 8 1.3 0.5 -------- UNIT V mV mV mV Load Regulation REGload mV Quiescent Current Iq mA mA Quiescent Current Change ΔIq mA Output Noise Voltage Vn μV Ripple Rejection Ratio RR dB Voltage Drop Vdrop V Output Resistance Rout mΩ Output Short Circuit Current Ios mA Peak Output Current Io peak A Temperature Coefficient of ΔVout/ΔTj mV/ Output Voltage ℃ * Pulse testing techniques are used to maintain the junction temperature as close to the ambient temperature as possible, and thermal effects must be taken into account separately. ** This specification applies only for DC power dissipation permitted by absolute maximum ratings. Line Regulation Tj=25℃ MIN. 4.80 2-9 2002/10.rev. A PJ7800 Series 3-Terminal Fixed Voltage Positive Regulators • PJ7806 ELECTRICAL CHARACTERISTICS (Vin=11V, Iout=500mA, 0℃≤Tj≤125℃, Cin=0.33μF, Cout=0.1μF; unless otherwise specified.) CHARACTERISTICS SYMBOL Output Voltage Vout Line Regulation REGline Load Regulation REGload Quiescent Current Quiescent Current Change Output Noise Voltage Ripple Rejection Ratio Voltage Drop Output Resistance Output Short Circuit Current Peak Output Current Temperature Coefficient of Output Voltage • Iq Δlq Vn RR Vdrop Rout Ios Io peak ΔVout/ΔTj TEST CONDITIONS MIN. TYP. MAX. Tj=25℃ 5.75 6 6.25 8V≤Vin≤21V, 5mA≤Iout≤1.5A, PD≤15W 6.3 6 6.3 Tj=25℃ --------59 ------ 5 1.5 14 4 4.3 --45 75 2 19 550 2.2 -0.7 120 60 120 60 8 1.3 0.5 -------- mV mV mV mV mA mA mA μV dB V mΩ mA A mV/℃ MIN. TYP. MAX. UNIT 7.69 7.61 --------56 ------ 8 8 6 2 12 4 4.3 --52 72 2 16 450 2.2 -0.8 8.32 8.40 160 80 160 80 8 1 0.5 -------- 8V≤Vin≤25V 9V≤Vin≤13V Tj=25℃ 5mA≤Iout≤1.5A 250mA≤Iout≤750mA Iout=0, Tj=25℃ 8V≤Vin≤25V 5mA≤Iout≤1.5A 10Hz≤f≤100KHz, Tj=25℃ f=120Hz, 9V≤Vin≤19V Iout=1.0A, Tj=25℃ f=1KHz Tj=25℃ Tj=25℃ Iout=5mA, 0℃≤Tj≤125℃ UNIT V PJ7808 ELECTRICAL CHARACTERISTICS (Vin=14V, Iout=500mA, 0℃≤Tj≤125℃, Cin=0.33μF, Cout=0.1μF; unless otherwise specified.) CHARACTERISTICS SYMBOL Output Voltage Vout Line Regulation REGline Load Regulation REGload Quiescent Current Quiescent Current Change Iq Δlq TEST CONDITIONS Tj=25℃ 10.5V≤Vin≤23V, 5mA≤Iout≤1.5A, PD ≤15W 10.5V≤Vin≤25V 11V≤Vin≤17V 10mA≤Iout≤1.5A Tj=25℃ 250mA≤Iout≤750mA Iout=0, Tj=25℃ 10.5V≤Vin≤25V 5mA≤Iout≤1.5A 10Hz≤f≤100KHz, Tj=25℃ f=120Hz, 11V≤Vin≤21V Iout=1.0A, Tj=25℃ f=1KHz Tj=25℃ Tj=25℃ Iout=5mA, 0℃≤Tj≤125℃ Tj=25℃ V mV mV mV mV mA mA mA μV dB V mΩ mA A mV/℃ Output Noise Voltage Vn Ripple Rejection Ratio RR Voltage Drop Vdrop Output Resistance Rout Output Short Circuit Current Ios Peak Output Current Io peak Temperature Coefficient of ΔVout/ΔTj Output Voltage * Pulse testing techniques are used to maintain the junction temperature as close to the ambient temperature as possible, and thermal effects must be taken into account separately. ** This specification applies only for DC power dissipation permitted by absolute maximum ratings. 3-9 2002/10.rev. A PJ7800 Series 3-Terminal Fixed Voltage Positive Regulators • PJ7809 ELECTRICAL CHARACTERISTICS (Vin=15V, Iout=500mA, 0℃≤Tj≤125℃, Cin=0.33μF, Cout=0.1μF; unless otherwise specified.) CHARACTERISTICS SYMBOL Output Voltage Vout Line Regulation REGline Load Regulation REGload Quiescent Current Quiescent Current Change Output Noise Voltage Ripple Rejection Ratio Voltage Drop Output Resistance Output Short Circuit Current Peak Output Current Temperature Coefficient of Output Voltage Iq Δlq Vn RR Vdrop Rout Ios Io peak ΔVout/ΔTj TEST CONDITIONS Tj=25℃ 10.5V≤Vin≤23V, 5mA≤Iout≤1.5A, PD ≤15W 11.5V≤Vin≤26V Tj=25℃ 11.5V≤Vin≤17V 5mA≤Iout≤1.5A Tj=25℃ 250mA≤Iout≤750mA Iout=0, Tj=25℃ 11.5V≤Vin≤26V 5mA≤Iout≤1.5A 10Hz≤f≤100KHz, Tj=25℃ f=120Hz, 11.5V≤Vin≤21.5V Iout=1.0A, Tj=25℃ f=1KHz Tj=25℃ Tj=25℃ Iout=5mA, 0℃≤Tj≤125℃ MIN. TYP. MAX. UNIT 8.65 8.57 --------55 ------ 9 9 6 2 12 4 4.3 --52 72 2 16 450 2.2 -1 9.36 9.45 180 90 180 90 8 1 0.5 -------- mV mV mV mV mA mA mA μV dB V mΩ mA A mV/℃ MIN. TYP. MAX. UNIT 9.6 9.5 --------55 ------ 10 10 7 2 12 4 4.3 --70 71 2 18 400 2.2 -1 10.4 10.5 200 100 200 100 8 1 0.5 -------- V • PJ7810 ELECTRICAL CHARACTERISTICS (Vin=16V, Iout=500mA, 0℃≤Tj≤125℃, Cin=0.33μF, Cout=0.1μF; unless otherwise specified.) CHARACTERISTICS SYMBOL Output Voltage Vout Line Regulation REGline Load Regulation REGload Quiescent Current Quiescent Current Change Iq Δlq TEST CONDITIONS Tj=25℃ 12.5V≤Vin≤25V, 5mA≤Iout≤1.5A, PD ≤15W 12.5V≤Vin≤28V 13V≤Vin≤17V 10mA≤Iout≤1.5A Tj=25℃ 250mA≤Iout≤750mA Iout=0, Tj=25℃ 12.5V≤Vin≤28V 5mA≤Iout≤1.5A 10Hz≤f≤100KHz, Tj=25℃ f=120Hz, 13V≤Vin≤23V Iout=1.0A, Tj=25℃ f=1KHz Tj=25℃ Tj=25℃ Iout=5mA, 0℃≤Tj≤125℃ Tj=25℃ V mV mV mV mV mA mA mA μV dB V mΩ mA A mV/℃ Output Noise Voltage Vn Ripple Rejection Ratio RR Voltage Drop Vdrop Output Resistance Rout Output Short Circuit Current Ios Peak Output Current Io peak Temperature Coefficient of ΔVout/ΔTj Output Voltage * Pulse testing techniques are used to maintain the junction temperature as close to the ambient temperature as possible, and thermal effects must be taken into account separately. ** This specification applies only for DC power dissipation permitted by absolute maximum ratings. 4-9 2002/10.rev. A PJ7800 Series 3-Terminal Fixed Voltage Positive Regulators • PJ7812 ELECTRICAL CHARACTERISTICS Vin=19V, Iout=500mA, 0℃≤Tj≤125℃, Cin=0.33μF, Cout=0.1μF; unless otherwise specified.) CHARACTERISTICS SYMBOL Output Voltage Vout Line Regulation REGline Load Regulation REGload Quiescent Current Quiescent Current Change Output Noise Voltage Ripple Rejection Ratio Voltage Drop Output Resistance Output Short Circuit Current Peak Output Current Temperature Coefficient of Output Voltage Iq Δlq Vn RR Vdrop Rout Ios Io peak ΔVout/ΔTj TEST CONDITIONS Tj=25℃ 14.5V≤Vin≤27V, 5mA≤Iout≤1.5A, PD ≤15W 14V≤Vin≤30V Tj=25℃ 15V≤Vin≤19V 10mA≤Iout≤1.5A Tj=25℃ 250mA≤Iout≤750mA Tj=25℃, Iout=0 14.5V≤Vin≤30V 5mA≤Iout≤1.5A 10Hz≤f≤100KHz, Tj=25℃ f=120Hz, 15V≤Vin≤25V Iout=1.0A, Tj=25℃ f=1KHz Tj=25℃ Tj=25℃ Iout=5mA, 0℃≤Tj≤125℃ MIN. TYP. MAX. UNIT 11.53 11.42 --------55 ------ 12 12 10 3 12 4 4.3 --75 71 2 18 350 2.2 -1 12.48 12.60 240 120 240 120 8 1 0.5 -------- mV mV mV mV mA mA mA μV dB V mΩ mA A mV/℃ MIN. TYP. MAX. UNIT 14.42 14.28 --------54 ------ 15 15 12 3 12 4 4.3 --90 70 2 19 230 2.2 -1 15.60 15.75 300 150 300 150 8 1 0.5 -------- V • PJ7815 ELECTRICAL CHARACTERISTICS (Vin=23V, Iout=500mA, 0℃≤Tj≤125℃, Cin=0.33μF, Cout=0.1μF; unless otherwise specified.) CHARACTERISTICS SYMBOL Output Voltage Vout Line Regulation REGline Load Regulation REGload Quiescent Current Quiescent Current Change Iq Δlq TEST CONDITIONS Tj=25℃ 17.5V≤Vin≤30V, 5mA≤Iout≤1.5A, PD ≤15W 17.5V≤Vin≤30V 18V≤Vin≤22V 10mA≤Iout≤1.5A Tj=25℃ 250mA≤Iout≤750mA Tj=25℃, Iout=0 17.5V≤Vin≤30V 5mA≤Iout≤1.5A 10Hz≤f≤100KHz, Tj=25℃ f=120Hz, 18V≤Vin≤28V Iout=1.0A, Tj=25℃ f=1KHz Tj=25℃ Tj=25℃ Iout=5mA, 0℃≤Tj≤125℃ Tj=25℃ V mV mV mV mV mA mA mA μV dB V mΩ mA A mV/℃ Output Noise Voltage Vn Ripple Rejection Ratio RR Voltage Drop Vdrop Output Resistance Rout Output Short Circuit Current Ios Peak Output Current Io peak Temperature Coefficient of ΔVout/ΔTj Output Voltage * Pulse testing techniques are used to maintain the junction temperature as close to the ambient temperature as possible, and thermal effects must be taken into account separately. ** This specification applies only for DC power dissipation permitted by absolute maximum ratings. 5-9 2002/10.rev. A PJ7800 Series 3-Terminal Fixed Voltage Positive Regulators • PJ7818 ELECTRICAL CHARACTERISTICS (Vin=27V, Iout=500mA, 0℃≤Tj≤125℃, Cin=0.33μF, Cout=0.1μF; unless otherwise specified.) CHARACTERISTICS SYMBOL Output Voltage Vout Line Regulation REGline Load Regulation REGload Quiescent Current Quiescent Current Change Output Noise Voltage Ripple Rejection Ratio Voltage Drop Output Resistance Output Short Circuit Current Peak Output Current Temperature Coefficient of Output Voltage Iq Δlq Vn RR Vdrop Rout Ios Io peak ΔVout/ΔTj TEST CONDITIONS Tj=25℃ 21V≤Vin≤33V, 5mA≤Iout≤1.5A, PD ≤15W 21V≤Vin≤33V Tj=25℃ 22V≤Vin≤26V 10mA≤Iout≤1.5A Tj=25℃ 250mA≤Iout≤750mA Tj=25℃, Iout=0 21V≤Vin≤33V 5mA≤Iout≤1.5A 10Hz≤f≤100KHz, Tj=25℃ f=120Hz, 21V≤Vin≤31V Iout=1.0A, Tj=25℃ f=1KHz Tj=25℃ Tj=25℃ Iout=5mA, 0℃≤Tj≤125℃ MIN. TYP. MAX. UNIT 17.30 17.14 --------54 ------ 18 18 15 5 12 4 4.5 --110 70 2 22 200 2.2 -1 18.72 18.90 360 180 360 180 8 1 0.5 -------- mV mV mV mV mA mA mA μV dB V mΩ mA A mV/℃ MIN. TYP. MAX. UNIT 23.07 22.85 --------54 ------ 24 24 18 6 12 4 4.6 --170 70 2 28 150 2.2 -1.5 24.96 25.20 480 240 480 240 8 1 0.5 -------- V PJ7824 BELECTRICAL CHARACTERISTICS (Vin=33V, Iout=500mA, 0℃≤Tj≤125℃, Cin=0.33μF, Cout=0.1μF; unless otherwise specified.) CHARACTERISTICS SYMBOL Output Voltage Vout Line Regulation REGline Load Regulation REGload Quiescent Current Quiescent Current Change Iq Δlq TEST CONDITIONS Tj=25℃ 26V≤Vin≤38V, 5mA≤Iout≤1.5A, PD ≤15W 26V≤Vin≤38V 27V≤Vin≤32V 10mA≤Iout≤1.5A Tj=25℃ 250mA≤Iout≤750mA Iout=0, Tj=25℃ 26V≤Vin≤38V 5mA≤Iout≤1.5A 10Hz≤f≤100KHz, Tj=25℃ f=120Hz, 26V≤Vin≤36V Iout=1.0A, Tj=25℃ f=1KHz Tj=25℃ Tj=25℃ Iout=5mA, 0℃≤Tj≤125℃ Tj=25℃ V mV mV mV mV mA mA mA μV dB V mΩ mA A mV/℃ Output Noise Voltage Vn Ripple Rejection Ratio RR Voltage Drop Vdrop Output Resistance Rout Output Short Circuit Current Ios Peak Output Current Io peak Temperature Coefficient of ΔVout/ΔTj Output Voltage * Pulse testing techniques are used to maintain the junction temperature as close to the ambient temperature as possible, and thermal effects must be taken into account separately. ** This specification applies only for DC power dissipation permitted by absolute maximum ratings. 6-9 2002/10.rev. A PJ7800 Series 3-Terminal Fixed Voltage Positive Regulators FIGURE 2 - PEAK OUTPUT CURRENT AS A FIGURE 1 - WORST CASE POWER DISSIPATION versus AMBIENT TEMPERATURE FUNCTION OF INPUT-OUTPUT DIFFERENTIAL VOLTAGE FIGURE 3 - QUIESCENT CURRENT AS A FUNCTION OF TEMPERATURE FIGURE 4 - INPUT OUTPUT DIFFERENTIAL AS A FUNCTION OF JUNCTION TEMPERATURE FIGURE 5 - OUTPUT VOLTAGE AS A FUNCTION OF JUNCTION TEMPERATURE 7-9 FIGURE 6 - OUTPUT IMPEDANCE AS A FUNCTION OF OUTPUT VOLTAGE 2002/10.rev. A PJ7800 Series 3-Terminal Fixed Voltage Positive Regulators FIGURE 7 - RIPPLE REJECTION AS A FUNCTION OF OUTPUT VOLTAGE 8-9 FIGURE 8 - RIPPLE REJECTION AS A FUNCTION OF FREQUENCY 2002/10.rev. A PJ7800 Series 3-Terminal Fixed Voltage Positive Regulators TO-220 Mechanical drawing DIM A B C D E F G H I J K L M N O P TO-220 DIMENSION MILLIMETERS INCHES MIN MAX MIN MAX 10.00 10.50 0.394 0.413 3.24 4.44 0.128 0.175 2.44 2.94 0.096 0.116 3.565 4.315 0.140 0.170 0.68 0.92 0.027 0.036 1.115 1.485 0.044 0.058 2.345 2.715 0.092 0.107 13.49 14.31 0.531 0.563 4.475 5.225 0.176 0.206 1.15 1.39 0.045 0.055 27.78 29.62 1.094 1.166 2.175 2.925 0.086 0.115 0.297 0.477 0.012 0.019 8.28 8.80 0.326 0.346 14.29 15.31 0.563 0.603 6.01 6.51 0.237 0.256 TO-220F Mechanical drawing DIM A B C D E F G H I J K L M N O 9-9 TO-220F DIMENSION MILLIMETERS INCHES MIN MAX MIN MAX 9.9 10.1 0.390 0.398 6.2 6.2 0.244 0.244 2.2 2.2 0.087 0.087 Φ1.4 Φ1.4 Φ0.055 Φ0.055 15.0 15.2 0.591 0.598 0.48 0.72 0.019 0.028 2.355 2.725 0.093 0.107 13.49 14.31 0.531 0.563 1.115 1.485 0.044 0.058 2.6 2.8 0.102 0.110 4.4 4.6 0.173 0.181 1.115 1.15 0.045 0.045 2.95 3.15 0.116 0.124 2.6 2.8 0.102 0.110 6.55 6.65 0.258 0.262 2002/10.rev. A