MICROCHIP PIC24HJXXXGPX10A

PIC24HJXXXGPX06A/X08A/X10A
Data Sheet
High-Performance,
16-bit Microcontrollers
 2009 Microchip Technology Inc.
Preliminary
DS70592B
Note the following details of the code protection feature on Microchip devices:
•
Microchip products meet the specification contained in their particular Microchip Data Sheet.
•
Microchip believes that its family of products is one of the most secure families of its kind on the market today, when used in the
intended manner and under normal conditions.
•
There are dishonest and possibly illegal methods used to breach the code protection feature. All of these methods, to our
knowledge, require using the Microchip products in a manner outside the operating specifications contained in Microchip’s Data
Sheets. Most likely, the person doing so is engaged in theft of intellectual property.
•
Microchip is willing to work with the customer who is concerned about the integrity of their code.
•
Neither Microchip nor any other semiconductor manufacturer can guarantee the security of their code. Code protection does not
mean that we are guaranteeing the product as “unbreakable.”
Code protection is constantly evolving. We at Microchip are committed to continuously improving the code protection features of our
products. Attempts to break Microchip’s code protection feature may be a violation of the Digital Millennium Copyright Act. If such acts
allow unauthorized access to your software or other copyrighted work, you may have a right to sue for relief under that Act.
Information contained in this publication regarding device
applications and the like is provided only for your convenience
and may be superseded by updates. It is your responsibility to
ensure that your application meets with your specifications.
MICROCHIP MAKES NO REPRESENTATIONS OR
WARRANTIES OF ANY KIND WHETHER EXPRESS OR
IMPLIED, WRITTEN OR ORAL, STATUTORY OR
OTHERWISE, RELATED TO THE INFORMATION,
INCLUDING BUT NOT LIMITED TO ITS CONDITION,
QUALITY, PERFORMANCE, MERCHANTABILITY OR
FITNESS FOR PURPOSE. Microchip disclaims all liability
arising from this information and its use. Use of Microchip
devices in life support and/or safety applications is entirely at
the buyer’s risk, and the buyer agrees to defend, indemnify and
hold harmless Microchip from any and all damages, claims,
suits, or expenses resulting from such use. No licenses are
conveyed, implicitly or otherwise, under any Microchip
intellectual property rights.
Trademarks
The Microchip name and logo, the Microchip logo, dsPIC,
KEELOQ, KEELOQ logo, MPLAB, PIC, PICmicro, PICSTART,
rfPIC and UNI/O are registered trademarks of Microchip
Technology Incorporated in the U.S.A. and other countries.
FilterLab, Hampshire, HI-TECH C, Linear Active Thermistor,
MXDEV, MXLAB, SEEVAL and The Embedded Control
Solutions Company are registered trademarks of Microchip
Technology Incorporated in the U.S.A.
Analog-for-the-Digital Age, Application Maestro, CodeGuard,
dsPICDEM, dsPICDEM.net, dsPICworks, dsSPEAK, ECAN,
ECONOMONITOR, FanSense, HI-TIDE, In-Circuit Serial
Programming, ICSP, Mindi, MiWi, MPASM, MPLAB Certified
logo, MPLIB, MPLINK, mTouch, Octopus, Omniscient Code
Generation, PICC, PICC-18, PICDEM, PICDEM.net, PICkit,
PICtail, PIC32 logo, REAL ICE, rfLAB, Select Mode, Total
Endurance, TSHARC, UniWinDriver, WiperLock and ZENA
are trademarks of Microchip Technology Incorporated in the
U.S.A. and other countries.
SQTP is a service mark of Microchip Technology Incorporated
in the U.S.A.
All other trademarks mentioned herein are property of their
respective companies.
© 2009, Microchip Technology Incorporated, Printed in the
U.S.A., All Rights Reserved.
Printed on recycled paper.
Microchip received ISO/TS-16949:2002 certification for its worldwide
headquarters, design and wafer fabrication facilities in Chandler and
Tempe, Arizona; Gresham, Oregon and design centers in California
and India. The Company’s quality system processes and procedures
are for its PIC® MCUs and dsPIC® DSCs, KEELOQ® code hopping
devices, Serial EEPROMs, microperipherals, nonvolatile memory and
analog products. In addition, Microchip’s quality system for the design
and manufacture of development systems is ISO 9001:2000 certified.
DS70592B-page 2
Preliminary
 2009 Microchip Technology Inc.
PIC24HJXXXGPX06A/X08A/X10A
High-Performance, 16-Bit Microcontrollers
Operating Range:
On-Chip Flash and SRAM:
• Up to 40 MIPS operation (@ 3.0-3.6V):
- Industrial temperature range (-40°C to +85°C)
- Extended temperature range (-40°C to +125°C)
• Up to 20 MIPS operation (@ 3.0-3.6V):
- High temperature range (-40°C to +140°C)
• Flash program memory, up to 256 Kbytes
• Data SRAM, up to 16 Kbytes (includes 2 Kbytes
of DMA RAM)
High-Performance CPU:
• Flexible clock options:
- External, crystal, resonator, internal RC
- Fully integrated PLL
- Extremely low jitter PLL
• Power-up Timer
• Oscillator Start-up Timer/Stabilizer
• Watchdog Timer with its own RC oscillator
• Fail-Safe Clock Monitor
• Reset by multiple sources
•
•
•
•
•
•
•
•
•
•
•
•
•
Modified Harvard architecture
C compiler optimized instruction set
16-bit wide data path
24-bit wide instructions
Linear program memory addressing up to 4M
instruction words
Linear data memory addressing up to 64 Kbytes
71 base instructions: mostly 1 word/1 cycle
Sixteen 16-bit General Purpose Registers
Flexible and powerful Indirect Addressing modes
Software stack
16 x 16 multiply operations
32/16 and 16/16 divide operations
Up to ±16-bit data shifts
Direct Memory Access (DMA):
• 8-channel hardware DMA
• 2 Kbytes dual ported DMA buffer area
(DMA RAM) to store data transferred via DMA:
- Allows data transfer between RAM and a
peripheral while CPU is executing code
(no cycle stealing)
• Most peripherals support DMA
Interrupt Controller:
•
•
•
•
•
5-cycle latency
Up to 61 available interrupt sources
Up to five external interrupts
Seven programmable priority levels
FIve processor exceptions
System Management:
Power Management:
• On-chip 2.5V voltage regulator
• Switch between clock sources in real time
• Idle, Sleep and Doze modes with fast wake-up
Timers/Capture/Compare/PWM:
• Timer/Counters, up to nine 16-bit timers:
- Can pair up to make four 32-bit timers
- One timer runs as Real-Time Clock with
external 32.768 kHz oscillator
- Programmable prescaler
• Input Capture (up to eight channels):
- Capture on up, down or both edges
- 16-bit capture input functions
- 4-deep FIFO on each capture
• Output Compare (up to eight channels):
- Single or Dual 16-Bit Compare mode
- 16-bit Glitchless PWM mode
Digital I/O:
•
•
•
•
•
Up to 85 programmable digital I/O pins
Wake-up/Interrupt-on-Change on up to 24 pins
Output pins can drive from 3.0V to 3.6V
All digital input pins are 5V tolerant
4 mA sink on all I/O pins
 2009 Microchip Technology Inc.
Preliminary
DS70592B-page 3
PIC24HJXXXGPX06A/X08A/X10A
Communication Modules:
Analog-to-Digital Converters:
• 3-wire SPI (up to two modules):
- Framing supports I/O interface to simple
codecs
- Supports 8-bit and 16-bit data
- Supports all serial clock formats and
sampling modes
• I2C™ (up to two modules):
- Full Multi-Master Slave mode support
- 7-bit and 10-bit addressing
- Bus collision detection and arbitration
- Integrated signal conditioning
- Slave address masking
• UART (up to two modules):
- Interrupt on address bit detect
- Interrupt on UART error
- Wake-up on Start bit from Sleep mode
- 4-character TX and RX FIFO buffers
- LIN bus support
- IrDA® encoding and decoding in hardware
- High-Speed Baud mode
- Hardware Flow Control with CTS and RTS
• Enhanced CAN (ECAN™ module) 2.0B active
(up to two modules):
- Up to eight transmit and up to 32 receive buffers
- 16 receive filters and 3 masks
- Loopback, Listen Only and Listen All
Messages modes for diagnostics and bus
monitoring
- Wake-up on CAN message
- Automatic processing of Remote
Transmission Requests
- FIFO mode using DMA
- DeviceNet™ addressing support
• Up to two Analog-to-Digital Converter (ADC)
modules in a device
• 10-bit, 1.1 Msps or 12-bit, 500 ksps conversion:
- Two, four, or eight simultaneous samples
- Up to 32 input channels with auto-scanning
- Conversion start can be manual or
synchronized with one of four trigger sources
- Conversion possible in Sleep mode
- ±1 LSb max integral nonlinearity
- ±1 LSb max differential nonlinearity
DS70592B-page 4
CMOS Flash Technology:
•
•
•
•
•
Low-power, high-speed Flash technology
Fully static design
3.3V (±10%) operating voltage
Industrial and extended temperature
Low-power consumption
Packaging:
• 100-pin TQFP (14x14x1 mm and 12x12x1 mm)
• 64-pin TQFP (10x10x1 mm)
• 64-pin QFN (9x9x0.9 mm)
Note:
Preliminary
See the device variant tables for exact
peripheral features per device.
 2009 Microchip Technology Inc.
PIC24HJXXXGPX06A/X08A/X10A
PIC24H PRODUCT FAMILIES
The PIC24H Family of devices is ideal for a wide variety of 16-bit MCU embedded applications. The device
names, pin counts, memory sizes and peripheral availability of each device are listed below, followed by their
pinout diagrams.
Pins
Program
Flash
Memory (KB)
RAM(1) (KB)
DMA Channels
Timer 16-bit
Input Capture
Output Compare
Std. PWM
Codec
Interface
ADC
UART
SPI
I2C™
CAN
I/O Pins (Max)(2)
Packages
PIC24H Family Controllers
PIC24HJ64GP206A
64
64
8
8
9
8
8
0
1 ADC,
18 ch
2
2
1
0
53
PT, MR
PIC24HJ64GP210A
100
64
8
8
9
8
8
0
1 ADC,
32 ch
2
2
2
0
85
PF, PT
PIC24HJ64GP506A
64
64
8
8
9
8
8
0
1 ADC,
18 ch
2
2
2
1
53
PT, MR
PIC24HJ64GP510A
100
64
8
8
9
8
8
0
1 ADC,
32 ch
2
2
2
1
85
PF, PT
PIC24HJ128GP206A
64
128
8
8
9
8
8
0
1 ADC,
18 ch
2
2
2
0
53
PT, MR
PIC24HJ128GP210A 100
128
8
8
9
8
8
0
1 ADC,
32 ch
2
2
2
0
85
PF, PT
PIC24HJ128GP506A
64
128
8
8
9
8
8
0
1 ADC,
18 ch
2
2
2
1
53
PT, MR
PIC24HJ128GP510A 100
128
8
8
9
8
8
0
1 ADC,
32 ch
2
2
2
1
85
PF, PT
PIC24HJ128GP306A
64
128
16
8
9
8
8
0
1 ADC,
18 ch
2
2
2
0
53
PT, MR
PIC24HJ128GP310A 100
128
16
8
9
8
8
0
1 ADC,
32 ch
2
2
2
0
85
PF, PT
PIC24HJ256GP206A
64
256
16
8
9
8
8
0
1 ADC,
18 ch
2
2
2
0
53
PT, MR
PIC24HJ256GP210A 100
256
16
8
9
8
8
0
1 ADC,
32 ch
2
2
2
0
85
PF, PT
PIC24HJ256GP610A 100
256
16
8
9
8
8
0
2 ADC,
32 ch
2
2
2
2
85
PF, PT
Device
Note 1:
2:
RAM size is inclusive of 2 Kbytes DMA RAM.
Maximum I/O pin count includes pins shared by the peripheral functions.
 2009 Microchip Technology Inc.
Preliminary
DS70592B-page 5
PIC24HJXXXGPX06A/X08A/X10A
Pin Diagrams
64-Pin QFN(1)
RG13
RG12
RG14
RG0
RG1
RF1
RF0
VDD
VCAP/VDDCORE
OC8/CN16/RD7
OC7/CN15/RD6
OC6/IC6/CN14/RD5
OC5/IC5/CN13/RD4
OC4/RD3
OC3/RD2
OC2/RD1
= Pins are up to 5V tolerant
64 63 62 61 60 59 58 57 56 55 54 53 52 51 50 49
RG15
AN16/T2CK/T7CK/RC1
AN17/T3CK/T6CK/RC2
SCK2/CN8/RG6
SDI2/CN9/RG7
SDO2/CN10/RG8
MCLR
SS2/CN11/RG9
VSS
VDD
AN5/IC8/CN7/RB5
AN4/IC7/CN6/RB4
AN3/CN5/RB3
AN2/SS1/CN4/RB2
PGEC3/AN1/VREF-/CN3/RB1
PGED3/AN0/VREF+/CN2/RB0
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
PIC24HJ64GP206A(2)
PIC24HJ128GP206A
PIC24HJ256GP206A
48
47
46
45
44
43
42
41
40
39
38
37
36
35
34
33
PGEC2/SOSCO/T1CK/CN0/RC14
PGED2/SOSCI/T4CK/CN1/RC13
OC1/RD0
IC4/INT4/RD11
IC3/INT3/RD10
IC2/U1CTS/INT2/RD9
IC1/INT1/RD8
VSS
OSC2/CLKO/RC15
OSC1/CLKIN/RC12
VDD
SCL1/RG2
SDA1/RG3
U1RTS/SCK1/INT0/RF6
U1RX/SDI1/RF2
U1TX/SDO1/RF3
PGEC1/AN6/OCFA/RB6
PGED1/AN7/RB7
AVDD
AVSS
U2CTS/AN8/RB8
AN9/RB9
TMS/AN10/RB10
TDO/AN11/RB11
VSS
VDD
TCK/AN12/RB12
TDI/AN13/RB13
U2RTS/AN14/RB14
AN15/OCFB/CN12/RB15
U2RX/SDA2/CN17/RF4
U2TX/SCL2/CN18/RF5
17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32
Note 1: The metal plane at the bottom of the device is not connected to any pins and should be connected
to VSS externally.
2: The PIC24HJ64GP206A device does not have the SCL2 and SDA2 pins.
DS70592B-page 6
Preliminary
 2009 Microchip Technology Inc.
PIC24HJXXXGPX06A/X08A/X10A
Pin Diagrams (Continued)
64-Pin QFN(1)
RG13
RG12
RG14
RG0
RG1
RF1
RF0
VDD
VCAP/VDDCORE
OC8/CN16/RD7
OC7/CN15/RD6
OC6/IC6/CN14/RD5
OC5/IC5/CN13/RD4
OC4/RD3
OC3/RD2
OC2/RD1
= Pins are up to 5V tolerant
64 63 62 61 60 59 58 57 56 55 54 53 52 51 50 49
RG15
AN16/T2CK/T7CK/RC1
AN17/T3CK/T6CK/RC2
SCK2/CN8/RG6
SDI2/CN9/RG7
SDO2/CN10/RG8
MCLR
SS2/CN11/RG9
VSS
VDD
AN5/IC8/CN7/RB5
AN4/IC7/CN6/RB4
AN3/CN5/RB3
AN2/SS1/CN4/RB2
PGEC3/AN1/VREF-/CN3/RB1
PGED3/AN0/VREF+/CN2/RB0
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
PIC24HJ128GP306A
48
47
46
45
44
43
42
41
40
39
38
37
36
35
34
33
PGEC2/SOSCO/T1CK/CN0/RC14
PGED2/SOSCI/T4CK/CN1/RC13
OC1/RD0
IC4/INT4/RD11
IC3/INT3/RD10
IC2/U1CTS/INT2/RD9
IC1/INT1/RD8
VSS
OSC2/CLKO/RC15
OSC1/CLKIN/RC12
VDD
SCL1/RG2
SDA1/RG3
U1RTS/SCK1/INT0/RF6
U1RX/SDI1/RF2
U1TX/SDO1/RF3
PGEC1/AN6/OCFA/RB6
PGED1/AN7/RB7
AVDD
AVSS
U2CTS/AN8/RB8
AN9/RB9
TMS/AN10/RB10
TDO/AN11/RB11
VSS
VDD
TCK/AN12/RB12
TDI/AN13/RB13
U2RTS/AN14/RB14
AN15/OCFB/CN12/RB15
U2RX/SDA2/CN17/RF4
U2TX/SCL2/CN18/RF5
17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32
Note 1: The metal plane at the bottom of the device is not connected to any pins and should be connected
to VSS externally.
 2009 Microchip Technology Inc.
Preliminary
DS70592B-page 7
PIC24HJXXXGPX06A/X08A/X10A
Pin Diagrams (Continued)
64-Pin QFN(1)
RG13
RG12
RG14
RG0
RG1
C1TX/RF1
C1RX/RF0
VDD
VCAP/VDDCORE
OC8/CN16/RD7
OC7/CN15/RD6
OC6/IC6/CN14/RD5
OC5/IC5/CN13/RD4
OC4/RD3
OC3/RD2
OC2/RD1
= Pins are up to 5V tolerant
64 63 62 61 60 59 58 57 56 55 54 53 52 51 50 49
RG15
AN16/T2CK/T7CK/RC1
AN17/T3CK/T6CK/RC2
SCK2/CN8/RG6
SDI2/CN9/RG7
SDO2/CN10/RG8
MCLR
SS2/CN11/RG9
VSS
VDD
AN5/IC8/CN7/RB5
AN4/IC7/CN6/RB4
AN3/CN5/RB3
AN2/SS1/CN4/RB2
PGEC3/AN1/VREF-/CN3/RB1
PGED3/AN0/VREF+/CN2/RB0
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
PIC24HJ64GP506A
PIC24HJ128GP506A
48
47
46
45
44
43
42
41
40
39
38
37
36
35
34
33
PGEC2/SOSCO/T1CK/CN0/RC14
PGED2/SOSCI/T4CK/CN1/RC13
OC1/RD0
IC4/INT4/RD11
IC3/INT3/RD10
IC2/U1CTS/INT2/RD9
IC1/INT1/RD8
VSS
OSC2/CLKO/RC15
OSC1/CLKIN/RC12
VDD
SCL1/RG2
SDA1/RG3
U1RTS/SCK1/INT0/RF6
U1RX/SDI1/RF2
U1TX/SDO1/RF3
PGEC1/AN6/OCFA/RB6
PGED1/AN7/RB7
AVDD
AVSS
U2CTS/AN8/RB8
AN9/RB9
TMS/AN10/RB10
TDO/AN11/RB11
VSS
VDD
TCK/AN12/RB12
TDI/AN13/RB13
U2RTS/AN14/RB14
AN15/OCFB/CN12/RB15
U2RX/SDA2/CN17/RF4
U2TX/SCL2/CN18/RF5
17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32
Note 1: The metal plane at the bottom of the device is not connected to any pins and should be connected
to VSS externally.
DS70592B-page 8
Preliminary
 2009 Microchip Technology Inc.
PIC24HJXXXGPX06A/X08A/X10A
Pin Diagrams (Continued)
64-Pin TQFP
64
63
62
61
60
59
58
57
56
55
54
53
52
51
50
49
RG13
RG12
RG14
RG0
RG1
RF1
RF0
VDD
VCAP/VDDCORE
OC8/CN16/RD7
OC7/CN15/RD6
OC6/IC6/CN14/RD5
OC5/IC5/CN13/RD4
OC4/RD3
OC3/RD2
OC2/RD1
= Pins are up to 5V tolerant
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
PIC24HJ64GP206A
PIC24HJ128GP206A
PIC24HJ256GP206A
48
47
46
45
44
43
42
41
40
39
38
37
36
35
34
33
PGEC2/SOSCO/T1CK/CN0/RC14
PGED2/SOSCI/T4CK/CN1/RC13
OC1/RD0
IC4/INT4/RD11
IC3/INT3/RD10
IC2/U1CTS/INT2/RD9
IC1/INT1/RD8
VSS
OSC2/CLKO/RC15
OSC1/CLKIN/RC12
VDD
SCL1/RG2
SDA1/RG3
U1RTS/SCK1/INT0/RF6
U1RX/SDI1/RF2
U1TX/SDO1/RF3
PGEC1/AN6/OCFA/RB6
PGED1/AN7/RB7
AVDD
AVSS
U2CTS/AN8/RB8
AN9/RB9
TMS/AN10/RB10
TDO/AN11/RB11
VSS
VDD
TCK/AN12/RB12
TDI/AN13/RB13
U2RTS/AN14/RB14
AN15/OCFB/CN12/RB15
U2RX/SDA2/CN17/RF4
U2TX/SCL2/CN18/RF5
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
RG15
AN16/T2CK/T7CK/RC1
AN17/T3CK/T6CK/RC2
SCK2/CN8/RG6
SDI2/CN9/RG7
SDO2/CN10/RG8
MCLR
SS2/CN11/RG9
VSS
VDD
AN5/IC8/CN7/RB5
AN4/IC7/CN6/RB4
AN3/CN5/RB3
AN2/SS1/CN4/RB2
PGEC3/AN1/VREF-/CN3/RB1
PGED3/AN0/VREF+/CN2/RB0
Note:
The PIC24HJ64GP206A device does not have the SCL2 and SDA2 pins.
 2009 Microchip Technology Inc.
Preliminary
DS70592B-page 9
PIC24HJXXXGPX06A/X08A/X10A
Pin Diagrams (Continued)
64-Pin TQFP
64
63
62
61
60
59
58
57
56
55
54
53
52
51
50
49
RG13
RG12
RG14
RG0
RG1
RF1
RF0
VDD
VCAP/VDDCORE
OC8/CN16/RD7
OC7/CN15/RD6
OC6/IC6/CN14/RD5
OC5/IC5/CN13/RD4
OC4/RD3
OC3/RD2
OC2/RD1
= Pins are up to 5V tolerant
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
PIC24HJ128GP306A
48
47
46
45
44
43
42
41
40
39
38
37
36
35
34
33
PGEC2/SOSCO/T1CK/CN0/RC14
PGED2/SOSCI/T4CK/CN1/RC13
OC1/RD0
IC4/INT4/RD11
IC3/INT3/RD10
IC2/U1CTS/INT2/RD9
IC1/INT1/RD8
VSS
OSC2/CLKO/RC15
OSC1/CLKIN/RC12
VDD
SCL1/RG2
SDA1/RG3
U1RTS/SCK1/INT0/RF6
U1RX/SDI1/RF2
U1TX/SDO1/RF3
PGEC1/AN6/OCFA/RB6
PGED1/AN7/RB7
AVDD
AVSS
U2CTS/AN8/RB8
AN9/RB9
TMS/AN10/RB10
TDO/AN11/RB11
VSS
VDD
TCK/AN12/RB12
TDI/AN13/RB13
U2RTS/AN14/RB14
AN15/OCFB/CN12/RB15
U2RX/SDA2/CN17/RF4
U2TX/SCL2/CN18/RF5
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
RG15
AN16/T2CK/T7CK/RC1
AN17/T3CK/T6CK/RC2
SCK2/CN8/RG6
SDI2/CN9/RG7
SDO2/CN10/RG8
MCLR
SS2/CN11/RG9
VSS
VDD
AN5/IC8/CN7/RB5
AN4/IC7/CN6/RB4
AN3/CN5/RB3
AN2/SS1/CN4/RB2
PGEC3/AN1/VREF-/CN3/RB1
PGED3/AN0/VREF+/CN2/RB0
DS70592B-page 10
Preliminary
 2009 Microchip Technology Inc.
PIC24HJXXXGPX06A/X08A/X10A
Pin Diagrams (Continued)
64-Pin TQFP
64
63
62
61
60
59
58
57
56
55
54
53
52
51
50
49
RG13
RG12
RG14
RG0
RG1
C1TX/RF1
C1RX/RF0
VDD
VCAP/VDDCORE
OC8/CN16/RD7
OC7/CN15/RD6
OC6/IC6/CN14/RD5
OC5/IC5/CN13/RD4
OC4/RD3
OC3/RD2
OC2/RD1
= Pins are up to 5V tolerant
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
PIC24HJ64GP506A
PIC24HJ128GP506A
48
47
46
45
44
43
42
41
40
39
38
37
36
35
34
33
PGEC2/SOSCO/T1CK/CN0/RC14
PGED2/SOSCI/T4CK/CN1/RC13
OC1/RD0
IC4/INT4/RD11
IC3/INT3/RD10
IC2/U1CTS/INT2/RD9
IC1/INT1/RD8
VSS
OSC2/CLKO/RC15
OSC1/CLKIN/RC12
VDD
SCL1/RG2
SDA1/RG3
U1RTS/SCK1/INT0/RF6
U1RX/SDI1/RF2
U1TX/SDO1/RF3
PGEC1/AN6/OCFA/RB6
PGED1/AN7/RB7
AVDD
AVSS
U2CTS/AN8/RB8
AN9/RB9
TMS/AN10/RB10
TDO/AN11/RB11
VSS
VDD
TCK/AN12/RB12
TDI/AN13/RB13
U2RTS/AN14/RB14
AN15/OCFB/CN12/RB15
U2RX/SDA2/CN17/RF4
U2TX/SCL2/CN18/RF5
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
RG15
AN16/T2CK/T7CK/RC1
AN17/T3CK/T6CK/RC2
SCK2/CN8/RG6
SDI2/CN9/RG7
SDO2/CN10/RG8
MCLR
SS2/CN11/RG9
VSS
VDD
AN5/IC8/CN7/RB5
AN4/IC7/CN6/RB4
AN3/CN5/RB3
AN2/SS1/CN4/RB2
PGEC3/AN1/VREF-/CN3/RB1
PGED3/AN0/VREF+/CN2/RB0
 2009 Microchip Technology Inc.
Preliminary
DS70592B-page 11
PIC24HJXXXGPX06A/X08A/X10A
Pin Diagrams (Continued)
= Pins are up to 5V tolerant
100
99
98
97
96
95
94
93
92
91
90
89
88
87
86
85
84
83
82
81
80
79
78
77
76
AN28/RE4
AN27/RE3
AN26/RE2
RG13
RG12
RG14
AN25/RE1
AN24/RE0
AN23/CN23/RA7
AN22/CN22/RA6
RG0
RG1
RF1
RF0
VDD
VCAP/VDDCORE
OC8/CN16/RD7
OC7/CN15/RD6
OC6/CN14/RD5
OC5/CN13/RD4
IC6/CN19/RD13
IC5/RD12
OC4/RD3
OC3/RD2
OC2/RD1
100-Pin TQFP
RG15
VDD
AN29/RE5
AN30/RE6
AN31/RE7
AN16/T2CK/T7CK/RC1
AN17/T3CK/T6CK/RC2
AN18/T4CK/T9CK/RC3
AN19/T5CK/T8CK/RC4
SCK2/CN8/RG6
SDI2/CN9/RG7
SDO2/CN10/RG8
MCLR
SS2/CN11/RG9
VSS
VDD
TMS/RA0
AN20/INT1/RA12
AN21/INT2/RA13
AN5/CN7/RB5
AN4/CN6/RB4
AN3/CN5/RB3
AN2/SS1/CN4/RB2
PGEC3/AN1/CN3/RB1
75
VSS
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
74
PGEC2/SOSCO/T1CK/CN0/RC14
73
PGED2/SOSCI/CN1/RC13
OC1/RD0
IC4/RD11
72
71
70
69
68
67
66
PIC24HJ64GP210A
PIC24HJ128GP210A
PIC24HJ128GP310A
PIC24HJ256GP210A
23
24
25
65
64
63
62
IC3/RD10
IC2/RD9
IC1/RD8
INT4/RA15
INT3/RA14
VSS
61
60
OSC2/CLKO/RC15
OSC1/CLKIN/RC12
VDD
TDO/RA5
TDI/RA4
59
58
SDA2/RA3
SCL2/RA2
57
56
55
SCL1/RG2
SDA1/RG3
SCK1/INT0/RF6
54
53
52
51
SDI1/RF7
SDO1/RF8
U1RX/RF2
U1TX/RF3
PGEC1/AN6/OCFA/RB6
26
PGED1PGED1/AN7/RB727
VREF-/RA9
28
VREF+/RA10
29
30
AVDD
31
AVSS
32
AN8/RB8
33
AN9/RB9
34
AN10/RB10
35
AN11/RB11
36
VSS
VDD
37
38
TCK/RA1
U2RTS/RF13
39
40
U2CTS/RF12
41
AN12/RB12
42
AN13/RB13
43
AN14/RB14
44
AN15/OCFB/CN12/RB15
45
VSS
46
VDD
47
IC7/U1CTS/CN20/RD14
48
IC8/U1RTS/CN21/RD15
49
U2RX/CN17/RF4
50
U2TX/CN18/RF5
PGED3/AN0/CN2/RB0
1
DS70592B-page 12
Preliminary
 2009 Microchip Technology Inc.
PIC24HJXXXGPX06A/X08A/X10A
Pin Diagrams (Continued)
100-Pin TQFP
100
99
98
97
96
95
94
93
92
91
90
89
88
87
86
85
84
83
82
81
80
79
78
77
76
AN28/RE4
AN27/RE3
AN26/RE2
RG13
RG12
RG14
AN25/RE1
AN24/RE0
AN23/CN23/RA7
AN22/CN22/RA6
RG0
RG1
C1TX/RF1
C1RX/RF0
VDD
VCAP/VDDCORE
OC8/CN16/RD7
OC7/CN15/RD6
OC6/CN14/RD5
OC5/CN13/RD4
IC6/CN19/RD13
IC5/RD12
OC4/RD3
OC3/RD2
OC2/RD1
= Pins are up to 5V tolerant
RG15
VDD
AN29/RE5
AN30/RE6
AN31/RE7
AN16/T2CK/T7CK/RC1
AN17/T3CK/T6CK/RC2
AN18/T4CK/T9CK/RC3
AN19/T5CK/T8CK/RC4
SCK2/CN8/RG6
SDI2/CN9/RG7
SDO2/CN10/RG8
MCLR
SS2/CN11/RG9
VSS
VDD
TMS/RA0
AN20/INT1/RA12
AN21/INT2/RA13
AN5/CN7/RB5
AN4/CN6/RB4
AN3/CN5/RB3
AN2/SS1/CN4/RB2
PGEC3/AN1/CN3/RB1
75
74
VSS
PGEC2/SOSCO/T1CK/CN0/RC14
73
PGED2/SOSCI/CN1/RC13
OC1/RD0
5
6
7
8
9
71
70
69
68
67
66
72
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
PIC24HJ64GP510A
PIC24HJ128GP510A
65
64
63
62
61
60
59
58
57
56
55
54
53
52
51
IC4/RD11
IC3/RD10
IC2/RD9
IC1/RD8
INT4/RA15
INT3/RA14
VSS
OSC2/CLKO/RC15
OSC1/CLKIN/RC12
VDD
TDO/RA5
TDI/RA4
SDA2/RA3
SCL2/RA2
SCL1/RG2
SDA1/RG3
SCK1/INT0/RF6
SDI1/RF7
SDO1/RF8
U1RX/RF2
U1TX/RF3
PGEC1/AN6/OCFA/RB6
PGED1/AN7/RB7
VREF-/RA9
VREF+/RA10
AVDD
AVSS
AN8/RB8
AN9/RB9
AN10/RB10
AN11/RB11
VSS
VDD
TCK/RA1
U2RTS/RF13
U2CTS/RF12
AN12/RB12
AN13/RB13
AN14/RB14
AN15/OCFB/CN12/RB15
VSS
VDD
IC7/U1CTS/CN20/RD14
IC8/U1RTS/CN21/RD15
U2RX/CN17/RF4
U2TX/CN18/RF5
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
PGED3/AN0/CN2/RB0
1
2
3
4
 2009 Microchip Technology Inc.
Preliminary
DS70592B-page 13
PIC24HJXXXGPX06A/X08A/X10A
Pin Diagrams (Continued)
100-Pin TQFP
100
99
98
97
96
95
94
93
92
91
90
89
88
87
86
85
84
83
82
81
80
79
78
77
76
AN28/RE4
AN27/RE3
AN26/RE2
RG13
RG12
RG14
AN25/RE1
AN24/RE0
AN23/CN23/RA7
AN22/CN22/RA6
C2RX/RG0
C2TX/RG1
C1TX/RF1
C1RX/RF0
VDD
VCAP/VDDCORE
OC8/CN16/RD7
OC7/CN15/RD6
OC6/CN14/RD5
OC5/CN13/RD4
IC6/CN19/RD13
IC5/RD12
OC4/RD3
OC3/RD2
OC2/RD1
= Pins are up to 5V tolerant
RG15
VDD
AN29/RE5
AN30/RE6
AN31/RE7
AN16/T2CK/T7CK/RC1
AN17/T3CK/T6CK/RC2
AN18/T4CK/T9CK/RC3
AN19/T5CK/T8CK/RC4
SCK2/CN8/RG6
SDI2/CN9/RG7
SDO2/CN10/RG8
MCLR
SS2/CN11/RG9
VSS
VDD
TMS/RA0
AN20/INT1/RA12
AN21/INT2/RA13
AN5/CN7/RB5
AN4/CN6/RB4
75
VSS
2
3
4
5
6
7
8
9
10
11
12
74
73
PGEC2/SOSCO/T1CK/CN0/RC14
PGED2/SOSCI/CN1/RC13
72
OC1/RD0
71
70
69
IC4/RD11
IC3/RD10
IC2/RD9
68
67
66
IC1/RD8
INT4/RA15
PIC24HJ256GP610A
13
14
15
16
17
18
19
20
21
22
23
24
25
65
64
63
62
61
60
59
58
INT3/RA14
VSS
OSC2/CLKO/RC15
OSC1/CLKIN/RC12
VDD
TDO/RA5
TDI/RA4
SDA2/RA3
SCL2/RA2
57
56
55
54
SCL1/RG2
SDA1/RG3
SCK1/INT0/RF6
53
52
51
SDO1/RF8
U1RX/RF2
SDI1/RF7
U1TX/RF3
PGEC1/AN6/OCFA/RB6
PGED1/AN7/RB7
VREF-/RA9
VREF+/RA10
AVDD
AVSS
AN8/RB8
AN9/RB9
AN10/RB10
AN11/RB11
VSS
VDD
TCK/RA1
U2RTS/RF13
U2CTS/RF12
AN12/RB12
AN13/RB13
AN14/RB14
AN15/OCFB/CN12/RB15
VSS
VDD
IC7/U1CTS/CN20/RD14
IC8/U1RTS/CN21/RD15
U2RX/CN17/RF4
U2TX/CN18/RF5
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
AN3/CN5/RB3
AN2/SS1/CN4/RB2
PGEC3/AN1/CN3/RB1
PGED3/AN0/CN2/RB0
1
DS70592B-page 14
Preliminary
 2009 Microchip Technology Inc.
PIC24HJXXXGPX06A/X08A/X10A
Table of Contents
PIC24H Product Families....................................................................................................................................................................... 5
1.0 Device Overview ........................................................................................................................................................................ 17
2.0 Guidelines for Getting Started with 16-Bit Microcontrollers........................................................................................................ 21
3.0 CPU............................................................................................................................................................................................ 25
4.0 Memory Organization ................................................................................................................................................................. 31
5.0 Flash Program Memory.............................................................................................................................................................. 61
6.0 Reset ......................................................................................................................................................................................... 67
7.0 Interrupt Controller ..................................................................................................................................................................... 73
8.0 Direct Memory Access (DMA) .................................................................................................................................................. 117
9.0 Oscillator Configuration ............................................................................................................................................................ 127
10.0 Power-Saving Features............................................................................................................................................................ 137
11.0 I/O Ports ................................................................................................................................................................................... 145
12.0 Timer1 ...................................................................................................................................................................................... 147
13.0 Timer2/3, Timer4/5, Timer6/7 and Timer8/9 ............................................................................................................................ 149
14.0 Input Capture............................................................................................................................................................................ 155
15.0 Output Compare....................................................................................................................................................................... 157
16.0 Serial Peripheral Interface (SPI)............................................................................................................................................... 161
17.0 Inter-Integrated Circuit™ (I2C™).............................................................................................................................................. 167
18.0 Universal Asynchronous Receiver Transmitter (UART) ........................................................................................................... 175
19.0 Enhanced CAN (ECAN™) Module........................................................................................................................................... 181
20.0 10-Bit/12-Bit Analog-to-Digital Converter (ADC) ...................................................................................................................... 207
21.0 Special Features ...................................................................................................................................................................... 219
22.0 Instruction Set Summary .......................................................................................................................................................... 227
23.0 Development Support............................................................................................................................................................... 235
24.0 Electrical Characteristics .......................................................................................................................................................... 239
25.0 High Temperature Electrical Characteristics ............................................................................................................................ 275
26.0 Packaging Information.............................................................................................................................................................. 285
Appendix A: Migrating from PIC24HJXXXGPX06/X08/X10 Devices to PIC24HJXXXGPX06A/X08A/X10A Devices ....................... 295
Appendix B: Revision History............................................................................................................................................................. 296
Index ................................................................................................................................................................................................. 297
The Microchip Web Site ..................................................................................................................................................................... 301
Customer Change Notification Service .............................................................................................................................................. 301
Customer Support .............................................................................................................................................................................. 301
Reader Response .............................................................................................................................................................................. 302
Product Identification System ............................................................................................................................................................ 303
 2009 Microchip Technology Inc.
Preliminary
DS70592B-page 15
PIC24HJXXXGPX06A/X08A/X10A
TO OUR VALUED CUSTOMERS
It is our intention to provide our valued customers with the best documentation possible to ensure successful use of your Microchip
products. To this end, we will continue to improve our publications to better suit your needs. Our publications will be refined and
enhanced as new volumes and updates are introduced.
If you have any questions or comments regarding this publication, please contact the Marketing Communications Department via
E-mail at [email protected] or fax the Reader Response Form in the back of this data sheet to (480) 792-4150. We
welcome your feedback.
Most Current Data Sheet
To obtain the most up-to-date version of this data sheet, please register at our Worldwide Web site at:
http://www.microchip.com
You can determine the version of a data sheet by examining its literature number found on the bottom outside corner of any page.
The last character of the literature number is the version number, (e.g., DS30000A is version A of document DS30000).
Errata
An errata sheet, describing minor operational differences from the data sheet and recommended workarounds, may exist for current
devices. As device/documentation issues become known to us, we will publish an errata sheet. The errata will specify the revision
of silicon and revision of document to which it applies.
To determine if an errata sheet exists for a particular device, please check with one of the following:
• Microchip’s Worldwide Web site; http://www.microchip.com
• Your local Microchip sales office (see last page)
When contacting a sales office, please specify which device, revision of silicon and data sheet (include literature number) you are
using.
Customer Notification System
Register on our web site at www.microchip.com to receive the most current information on all of our products.
DS70592B-page 16
Preliminary
 2009 Microchip Technology Inc.
PIC24HJXXXGPX06A/X08A/X10A
1.0
Note:
DEVICE OVERVIEW
This data sheet summarizes the features
of the PIC24HJXXXGPX06A/X08A/X10A
family of devices. However, it is not
intended to be a comprehensive reference
source. To complement the information in
this data sheet, refer to the latest family
reference
sections
of
the
“dsPIC33F/PIC24H Family Reference
Manual”, which is available from the
Microchip web site (www.microchip.com).
This document contains device specific information for
the following devices:
•
•
•
•
•
•
•
•
•
•
•
•
•
PIC24HJ64GP206A
PIC24HJ64GP210A
PIC24HJ64GP506A
PIC24HJ64GP510A
PIC24HJ128GP206A
PIC24HJ128GP210A
PIC24HJ128GP506A
PIC24HJ128GP510A
PIC24HJ128GP306A
PIC24HJ128GP310A
PIC24HJ256GP206A
PIC24HJ256GP210A
PIC24HJ256GP610A
The PIC24HJXXXGPX06A/X08A/X10A device family
includes devices with different pin counts (64 and 100
pins), different program memory sizes (64 Kbytes, 128
Kbytes and 256 Kbytes) and different RAM sizes (8
Kbytes and 16 Kbytes).
 2009 Microchip Technology Inc.
This makes these families suitable for a wide variety of
high-performance digital signal control applications.
The devices are pin compatible with the dsPIC33F family of devices, and also share a very high degree of
compatibility with the dsPIC30F family devices. This
allows easy migration between device families as may
be necessitated by the specific functionality, computational resource and system cost requirements of the
application.
The PIC24HJXXXGPX06A/X08A/X10A device family
employs a powerful 16-bit architecture, ideal for
applications that rely on high-speed, repetitive
computations, as well as control.
The 17 x 17 multiplier, hardware support for division
operations, multi-bit data shifter, a large array of 16-bit
working registers and a wide variety of data addressing
modes,
together
provide
the
PIC24HJXXXGPX06A/X08A/X10A Central Processing
Unit (CPU) with extensive mathematical processing
capability. Flexible and deterministic interrupt handling,
coupled with a powerful array of peripherals, renders
the PIC24HJXXXGPX06A/X08A/X10A devices suitable for control applications. Further, Direct Memory
Access (DMA) enables overhead-free transfer of data
between several peripherals and a dedicated DMA
RAM. Reliable, field programmable Flash program
memory ensures scalability of applications that use
PIC24HJXXXGPX06A/X08A/X10A devices.
Figure 1-1 shows a general block diagram of the
various core and peripheral modules in the
PIC24HJXXXGPX06A/X08A/X10A family of devices,
while Table 1-1 lists the functions of the various pins
shown in the pinout diagrams.
Preliminary
DS70592B-page 17
PIC24HJXXXGPX06A/X08A/X10A
FIGURE 1-1:
PIC24HJXXXGPX06A/X08A/X10A GENERAL BLOCK DIAGRAM
PSV and Table
Data Access
Control Block
Data Bus
Interrupt
Controller
PORTA
16
8
16
16
DMA
RAM
Data Latch
23
PCU PCH PCL
Program Counter
Loop
Stack
Control
Control
Logic
Logic
23
X RAM
PORTB
Address
Latch
DMA
23
16
Controller
16
PORTC
Address Generator Units
Address Latch
Program Memory
EA MUX
Data Latch
24
Instruction Reg
Control Signals
to Various Blocks
Timing
Generation
FRC/LPRC
Oscillators
Precision
Band Gap
Reference
Voltage
Regulator
VCAP/VDDCORE
Timers
1-9
IC1-8
Note:
Literal Data
16
Instruction
Decode and
Control
OSC2/CLKO
OSC1/CLKI
PORTD
ROM Latch
16
PORTE
16
17 x 17 Multiplier
Power-up
Timer
Divide Support
16 x 16
W Register Array
16
PORTF
Oscillator
Start-up Timer
Power-on
Reset
16-bit ALU
Watchdog
Timer
16
Brown-out
Reset
VDD, VSS
ADC1,2
OC/
PWM1-8
PORTG
MCLR
ECAN1,2
UART1,2
CN1-23
SPI1,2
I2C1,2
Not all pins or features are implemented on all device pinout configurations. See pinout diagrams for the specific pins
and features present on each device.
DS70592B-page 18
Preliminary
 2009 Microchip Technology Inc.
PIC24HJXXXGPX06A/X08A/X10A
TABLE 1-1:
PINOUT I/O DESCRIPTIONS
Pin
Type
Buffer
Type
AN0-AN31
I
Analog
AVDD
P
P
Positive supply for analog modules. This pin must be connected at all times.
AVSS
P
P
Ground reference for analog modules.
CLKI
CLKO
I
O
CN0-CN23
I
ST
Input change notification inputs.
Can be software programmed for internal weak pull-ups on all inputs.
C1RX
C1TX
C2RX
C2TX
I
O
I
O
ST
—
ST
—
ECAN1 bus receive pin.
ECAN1 bus transmit pin.
ECAN2 bus receive pin.
ECAN2 bus transmit pin.
PGED1
PGEC1
PGED2
PGEC2
PGED3
PGEC3
I/O
I
I/O
I
I/O
I
ST
ST
ST
ST
ST
ST
Data I/O pin for programming/debugging communication channel 1.
Clock input pin for programming/debugging communication channel 1.
Data I/O pin for programming/debugging communication channel 2.
Clock input pin for programming/debugging communication channel 2.
Data I/O pin for programming/debugging communication channel 3.
Clock input pin for programming/debugging communication channel 3.
IC1-IC8
I
ST
Capture inputs 1 through 8.
INT0
INT1
INT2
INT3
INT4
I
I
I
I
I
ST
ST
ST
ST
ST
External interrupt 0.
External interrupt 1.
External interrupt 2.
External interrupt 3.
External interrupt 4.
Pin Name
Description
Analog input channels.
ST/CMOS External clock source input. Always associated with OSC1 pin function.
—
Oscillator crystal output. Connects to crystal or resonator in Crystal Oscillator
mode. Optionally functions as CLKO in RC and EC modes. Always associated
with OSC2 pin function.
MCLR
I/P
ST
Master Clear (Reset) input. This pin is an active-low Reset to the device.
OCFA
OCFB
OC1-OC8
I
I
O
ST
ST
—
Compare Fault A input (for Compare Channels 1, 2, 3 and 4).
Compare Fault B input (for Compare Channels 5, 6, 7 and 8).
Compare outputs 1 through 8.
OSC1
I
OSC2
I/O
RA0-RA7
RA9-RA10
RA12-RA15
I/O
I/O
I/O
ST/CMOS Oscillator crystal input. ST buffer when configured in RC mode; CMOS
otherwise.
—
Oscillator crystal output. Connects to crystal or resonator in Crystal Oscillator
mode. Optionally functions as CLKO in RC and EC modes.
ST
ST
ST
PORTA is a bidirectional I/O port.
RB0-RB15
I/O
ST
PORTB is a bidirectional I/O port.
RC1-RC4
RC12-RC15
I/O
I/O
ST
ST
PORTC is a bidirectional I/O port.
RD0-RD15
I/O
ST
PORTD is a bidirectional I/O port.
RE0-RE7
I/O
ST
PORTE is a bidirectional I/O port.
RF0-RF8
RF12-RF13
I/O
ST
PORTF is a bidirectional I/O port.
RG0-RG3
RG6-RG9
RG12-RG15
I/O
I/O
I/O
ST
ST
ST
PORTG is a bidirectional I/O port.
Legend: CMOS = CMOS compatible input or output
ST = Schmitt Trigger input with CMOS levels
 2009 Microchip Technology Inc.
Analog = Analog input
O = Output
Preliminary
P = Power
I = Input
DS70592B-page 19
PIC24HJXXXGPX06A/X08A/X10A
TABLE 1-1:
PINOUT I/O DESCRIPTIONS (CONTINUED)
Pin
Type
Buffer
Type
SCK1
SDI1
SDO1
SS1
SCK2
SDI2
SDO2
SS2
I/O
I
O
I/O
I/O
I
O
I/O
ST
ST
—
ST
ST
ST
—
ST
Synchronous serial clock input/output for SPI1.
SPI1 data in.
SPI1 data out.
SPI1 slave synchronization or frame pulse I/O.
Synchronous serial clock input/output for SPI2.
SPI2 data in.
SPI2 data out.
SPI2 slave synchronization or frame pulse I/O.
SCL1
SDA1
SCL2
SDA2
I/O
I/O
I/O
I/O
ST
ST
ST
ST
Synchronous serial clock input/output for I2C1.
Synchronous serial data input/output for I2C1.
Synchronous serial clock input/output for I2C2.
Synchronous serial data input/output for I2C2.
SOSCI
SOSCO
I
O
TMS
TCK
TDI
TDO
I
I
I
O
ST
ST
ST
—
JTAG Test mode select pin.
JTAG test clock input pin.
JTAG test data input pin.
JTAG test data output pin.
T1CK
T2CK
T3CK
T4CK
T5CK
T6CK
T7CK
T8CK
T9CK
I
I
I
I
I
I
I
I
I
ST
ST
ST
ST
ST
ST
ST
ST
ST
Timer1 external clock input.
Timer2 external clock input.
Timer3 external clock input.
Timer4 external clock input.
Timer5 external clock input.
Timer6 external clock input.
Timer7 external clock input.
Timer8 external clock input.
Timer9 external clock input.
U1CTS
U1RTS
U1RX
U1TX
U2CTS
U2RTS
U2RX
U2TX
I
O
I
O
I
O
I
O
ST
—
ST
—
ST
—
ST
—
UART1 clear to send.
UART1 ready to send.
UART1 receive.
UART1 transmit.
UART2 clear to send.
UART2 ready to send.
UART2 receive.
UART2 transmit.
VDD
P
—
Positive supply for peripheral logic and I/O pins.
VCAP/VDDCORE
P
—
CPU logic filter capacitor connection.
VSS
P
—
Ground reference for logic and I/O pins.
VREF+
I
Analog
Analog voltage reference (high) input.
VREF-
I
Analog
Analog voltage reference (low) input.
Pin Name
Description
ST/CMOS 32.768 kHz low-power oscillator crystal input; CMOS otherwise.
—
32.768 kHz low-power oscillator crystal output.
Legend: CMOS = CMOS compatible input or output
ST = Schmitt Trigger input with CMOS levels
DS70592B-page 20
Analog = Analog input
O = Output
Preliminary
P = Power
I = Input
 2009 Microchip Technology Inc.
PIC24HJXXXGPX06A/X08A/X10A
2.0
GUIDELINES FOR GETTING
STARTED WITH 16-BIT
MICROCONTROLLERS
2.2
The use of decoupling capacitors on every pair of
power supply pins, such as VDD, VSS, AVDD and
AVSS is required.
Note 1: This data sheet summarizes the features
of the PIC24HJXXXGPX06A/X08A/X10A
family of devices. It is not intended to be
a comprehensive reference source. To
complement the information in this data
sheet, refer to the “dsPIC33F/PIC24H
Family Reference Manual”. Please see
the
Microchip
web
site
(www.microchip.com) for the latest
dsPIC33F/PIC24H Family Reference
Manual sections.
2: Some registers and associated bits
described in this section may not be available on all devices. Refer to Section 4.0
“Memory Organization” in this data
sheet for device-specific register and bit
information.
2.1
Decoupling Capacitors
Basic Connection Requirements
Getting
started
with
the
PIC24HJXXXGPX06A/X08A/X10A family of 16-bit
Microcontrollers (MCUs) requires attention to a minimal
set of device pin connections before proceeding with
development. The following is a list of pin names, which
must always be connected:
• All VDD and VSS pins
(see Section 2.2 “Decoupling Capacitors”)
• All AVDD and AVSS pins (regardless if ADC module
is not used)
(see Section 2.2 “Decoupling Capacitors”)
• VCAP/VDDCORE
(see Section 2.3 “Capacitor on Internal Voltage
Regulator (VCAP/VDDCORE)”)
• MCLR pin
(see Section 2.4 “Master Clear (MCLR) Pin”)
• PGECx/PGEDx pins used for In-Circuit Serial
Programming™ (ICSP™) and debugging purposes
(see Section 2.5 “ICSP Pins”)
• OSC1 and OSC2 pins when external oscillator
source is used
(see Section 2.6 “External Oscillator Pins”)
Consider the following criteria when using decoupling
capacitors:
• Value and type of capacitor: Recommendation
of 0.1 µF (100 nF), 10-20V. This capacitor should
be a low-ESR and have resonance frequency in
the range of 20 MHz and higher. It is
recommended that ceramic capacitors be used.
• Placement on the printed circuit board: The
decoupling capacitors should be placed as close
to the pins as possible. It is recommended to
place the capacitors on the same side of the
board as the device. If space is constricted, the
capacitor can be placed on another layer on the
PCB using a via; however, ensure that the trace
length from the pin to the capacitor is within
one-quarter inch (6 mm) in length.
• Handling high frequency noise: If the board is
experiencing high frequency noise, upward of
tens of MHz, add a second ceramic-type capacitor
in parallel to the above described decoupling
capacitor. The value of the second capacitor can
be in the range of 0.01 µF to 0.001 µF. Place this
second capacitor next to the primary decoupling
capacitor. In high-speed circuit designs, consider
implementing a decade pair of capacitances as
close to the power and ground pins as possible.
For example, 0.1 µF in parallel with 0.001 µF.
• Maximizing performance: On the board layout
from the power supply circuit, run the power and
return traces to the decoupling capacitors first,
and then to the device pins. This ensures that the
decoupling capacitors are first in the power chain.
Equally important is to keep the trace length
between the capacitor and the power pins to a
minimum thereby reducing PCB track inductance.
Additionally, the following pins may be required:
• VREF+/VREF- pins used when external voltage
reference for ADC module is implemented
Note:
The AVDD and AVSS pins must be
connected independent of the ADC
voltage reference source.
 2009 Microchip Technology Inc.
Preliminary
DS70592B-page 21
PIC24HJXXXGPX06A/X08A/X10A
FIGURE 2-1:
RECOMMENDED
MINIMUM CONNECTION
0.1 µF
Ceramic
R1
MCLR
C
10 
2.2.1
VDD
0.1 µF
Ceramic
VSS
VSS
AVSS
VDD
AVDD
0.1 µF
Ceramic
VDD
The MCLR pin provides for two specific device
functions:
During device programming and debugging, the
resistance and capacitance that can be added to the
pin must be considered. Device programmers and
debuggers drive the MCLR pin. Consequently,
specific voltage levels (VIH and VIL) and fast signal
transitions must not be adversely affected. Therefore,
specific values of R and C will need to be adjusted
based on the application and PCB requirements.
PIC24H
VSS
Master Clear (MCLR) Pin
• Device Reset
• Device programming and debugging
VSS
R
VDD
VCAP/VDDCORE
VDD
2.4
0.1 µF
Ceramic
0.1 µF
Ceramic
For example, as shown in Figure 2-2, it is
recommended that the capacitor C, be isolated from
the MCLR pin during programming and debugging
operations.
Place the components shown in Figure 2-2 within
one-quarter inch (6 mm) from the MCLR pin.
FIGURE 2-2:
TANK CAPACITORS
On boards with power traces running longer than six
inches in length, it is suggested to use a tank capacitor
for integrated circuits including MCUs to supply a local
power source. The value of the tank capacitor should
be determined based on the trace resistance that connects the power supply source to the device, and the
maximum current drawn by the device in the application. In other words, select the tank capacitor so that it
meets the acceptable voltage sag at the device. Typical
values range from 4.7 µF to 47 µF.
2.3
Capacitor on Internal Voltage
Regulator (VCAP/VDDCORE)
EXAMPLE OF MCLR PIN
CONNECTIONS
VDD
R
R1
MCLR
JP
PIC24H
C
Note 1:
R  10 k is recommended. A suggested
starting value is 10 k. Ensure that the MCLR
pin VIH and VIL specifications are met.
2:
R1  470 will limit any current flowing into
MCLR from the external capacitor C, in the
event of MCLR pin breakdown, due to
Electrostatic Discharge (ESD) or Electrical
Overstress (EOS). Ensure that the MCLR pin
VIH and VIL specifications are met.
A low-ESR (< 5 Ohms) capacitor is required on the
VCAP/VDDCORE pin, which is used to stabilize the
voltage regulator output voltage. The VCAP/VDDCORE
pin must not be connected to VDD, and must have a
capacitor between 4.7 µF and 10 µF, 16V connected to
ground. The type can be ceramic or tantalum. Refer to
Section 24.0 “Electrical Characteristics” for
additional information.
The placement of this capacitor should be close to the
VCAP/VDDCORE. It is recommended that the trace
length not exceed one-quarter inch (6 mm). Refer to
Section 21.2 “On-Chip Voltage Regulator” for
details.
DS70592B-page 22
Preliminary
 2009 Microchip Technology Inc.
PIC24HJXXXGPX06A/X08A/X10A
2.5
ICSP Pins
2.6
The PGECx and PGEDx pins are used for In-Circuit
Serial Programming™ (ICSP™) and debugging purposes. It is recommended to keep the trace length
between the ICSP connector and the ICSP pins on the
device as short as possible. If the ICSP connector is
expected to experience an ESD event, a series resistor
is recommended, with the value in the range of a few
tens of Ohms, not to exceed 100 Ohms.
Pull-up resistors, series diodes, and capacitors on the
PGECx and PGEDx pins are not recommended as they
will interfere with the programmer/debugger communications to the device. If such discrete components are
an application requirement, they should be removed
from the circuit during programming and debugging.
Alternatively, refer to the AC/DC characteristics and
timing requirements information in the respective
device Flash programming specification for information
on capacitive loading limits and pin input voltage high
(VIH) and input low (VIL) requirements.
Ensure that the “Communication Channel Select” (i.e.,
PGECx/PGEDx pins) programmed into the device
matches the physical connections for the ICSP to
MPLAB® ICD 2, MPLAB ICD 3 or MPLAB REAL ICE™.
Many MCUs have options for at least two oscillators: a
high-frequency primary oscillator and a low-frequency
secondary oscillator (refer to Section 9.0 “Oscillator
Configuration” for details).
The oscillator circuit should be placed on the same
side of the board as the device. Also, place the
oscillator circuit close to the respective oscillator pins,
not exceeding one-half inch (12 mm) distance
between them. The load capacitors should be placed
next to the oscillator itself, on the same side of the
board. Use a grounded copper pour around the
oscillator circuit to isolate them from surrounding
circuits. The grounded copper pour should be routed
directly to the MCU ground. Do not run any signal
traces or power traces inside the ground pour. Also, if
using a two-sided board, avoid any traces on the
other side of the board where the crystal is placed. A
suggested layout is shown in Figure 2-3.
FIGURE 2-3:
For more information on ICD 2, ICD 3 and REAL ICE
connection requirements, refer to the following
documents that are available on the Microchip website.
• “MPLAB® ICD 2 In-Circuit Debugger User’s
Guide” DS51331
• “Using MPLAB® ICD 2” (poster) DS51265
• “MPLAB® ICD 2 Design Advisory” DS51566
• “Using MPLAB® ICD 3 In-Circuit Debugger”
(poster) DS51765
• “MPLAB® ICD 3 Design Advisory” DS51764
• “MPLAB® REAL ICE™ In-Circuit Emulator User’s
Guide” DS51616
• “Using MPLAB® REAL ICE™” (poster) DS51749
 2009 Microchip Technology Inc.
External Oscillator Pins
Preliminary
SUGGESTED PLACEMENT
OF THE OSCILLATOR
CIRCUIT
Main Oscillator
13
Guard Ring
14
15
Guard Trace
Secondary
Oscillator
16
17
18
19
20
DS70592B-page 23
PIC24HJXXXGPX06A/X08A/X10A
2.7
Oscillator Value Conditions on
Device Start-up
If the PLL of the target device is enabled and
configured for the device start-up oscillator, the
maximum oscillator source frequency must be limited
to 4 MHz < FIN < 8 MHz to comply with device PLL
start-up conditions. This means that if the external
oscillator frequency is outside this range, the
application must start-up in the FRC mode first. The
default PLL settings after a POR with an oscillator
frequency outside this range will violate the device
operating speed.
Once the device powers up, the application firmware
can initialize the PLL SFRs, CLKDIV and PLLDBF to a
suitable value, and then perform a clock switch to the
Oscillator + PLL clock source. Note that clock switching
must be enabled in the device Configuration word.
2.8
Configuration of Analog and
Digital Pins During ICSP
Operations
If MPLAB ICD 2, ICD 3 or REAL ICE is selected as a
debugger, it automatically initializes all of the A/D input
pins (ANx) as “digital” pins, by setting all bits in the
AD1PCFGL register.
The bits in this register that correspond to the A/D pins
that are initialized by MPLAB ICD 2, ICD 3, or REAL
ICE, must not be cleared by the user application
firmware; otherwise, communication errors will result
between the debugger and the device.
If your application needs to use certain A/D pins as
analog input pins during the debug session, the user
application must clear the corresponding bits in the
AD1PCFGL register during initialization of the ADC
module.
When MPLAB ICD 2, ICD 3 or REAL ICE is used as a
programmer, the user application firmware must
correctly configure the AD1PCFGL register. Automatic
initialization of this register is only done during
debugger operation. Failure to correctly configure the
register(s) will result in all A/D pins being recognized as
analog input pins, resulting in the port value being read
as a logic ‘0’, which may affect user application
functionality.
2.9
Unused I/Os
Unused I/O pins should be configured as outputs and
driven to a logic-low state.
Alternatively, connect a 1k to 10k resistor to VSS on
unused pins and drive the output to logic low.
DS70592B-page 24
Preliminary
 2009 Microchip Technology Inc.
PIC24HJXXXGPX06A/X08A/X10A
3.0
CPU
3.1
Note 1: This data sheet summarizes the features
of the PIC24HJXXXGPX06A/X08A/X10A
family of devices. However, it is not
intended to be a comprehensive
reference source. To complement the
information in this data sheet, refer to
Section 2. “CPU” (DS70245) of the
“dsPIC33F/PIC24H Family Reference
Manual”, which is available from the
Microchip website (www.microchip.com).
2: Some registers and associated bits
described in this section may not be available on all devices. Refer to Section 4.0
“Memory Organization” in this data
sheet for device-specific register and bit
information.
The PIC24HJXXXGPX06A/X08A/X10A CPU module
has a 16-bit (data) modified Harvard architecture with an
enhanced instruction set and addressing modes. The
CPU has a 24-bit instruction word with a variable length
opcode field. The Program Counter (PC) is 23 bits wide
and addresses up to 4M x 24 bits of user program
memory space. The actual amount of program memory
implemented varies by device. A single-cycle instruction
prefetch mechanism is used to help maintain throughput
and provides predictable execution. All instructions
execute in a single cycle, with the exception of
instructions that change the program flow, the double
word move (MOV.D) instruction and the table instructions.
Overhead-free, single-cycle program loop constructs are
supported using the REPEAT instruction, which is
interruptible at any point.
Data Addressing Overview
The data space can be linearly addressed as 32K words
or 64 Kbytes using an Address Generation Unit (AGU).
The upper 32 Kbytes of the data space memory map can
optionally be mapped into program space at any 16K program word boundary defined by the 8-bit Program Space
Visibility Page (PSVPAG) register. The program to data
space mapping feature lets any instruction access program space as if it were data space.
The data space also includes 2 Kbytes of DMA RAM,
which is primarily used for DMA data transfers, but may
be used as general purpose RAM.
3.2
Special MCU Features
The PIC24HJXXXGPX06A/X08A/X10A features a
17-bit by 17-bit, single-cycle multiplier. The multiplier
can perform signed, unsigned and mixed-sign
multiplication. Using a 17-bit by 17-bit multiplier for
16-bit by 16-bit multiplication makes mixed-sign
multiplication possible.
The PIC24HJXXXGPX06A/X08A/X10A supports 16/16
and 32/16 integer divide operations. All divide
instructions are iterative operations. They must be
executed within a REPEAT loop, resulting in a total
execution time of 19 instruction cycles. The divide
operation can be interrupted during any of those
19 cycles without loss of data.
A multi-bit data shifter is used to perform up to a 16-bit,
left or right shift in a single cycle.
The PIC24HJXXXGPX06A/X08A/X10A devices have
sixteen, 16-bit working registers in the programmer’s
model. Each of the working registers can serve as a data,
address or address offset register. The 16th working
register (W15) operates as a software Stack Pointer (SP)
for interrupts and calls.
The PIC24HJXXXGPX06A/X08A/X10A instruction set
includes many addressing modes and is designed for
optimum C compiler efficiency. For most instructions,
the PIC24HJXXXGPX06A/X08A/X10A is capable of
executing a data (or program data) memory read, a
working register (data) read, a data memory write and
a program (instruction) memory read per instruction
cycle. As a result, three parameter instructions can be
supported, allowing A + B = C operations to be
executed in a single cycle.
A block diagram of the CPU is shown in Figure 3-1,
and
the
programmer’s
model
for
the
PIC24HJXXXGPX06A/X08A/X10A is shown in
Figure 3-2.
 2009 Microchip Technology Inc.
Preliminary
DS70592B-page 25
PIC24HJXXXGPX06A/X08A/X10A
FIGURE 3-1:
PIC24HJXXXGPX06A/X08A/X10A CPU CORE BLOCK DIAGRAM
PSV and Table
Data Access
Control Block
X Data Bus
Interrupt
Controller
8
16
16
16
Data Latch
DMA
23
23
PCU PCH PCL
Program Counter
Loop
Stack
Control
Control
Logic
Logic
X RAM
RAM
16
Address
Latch
23
16
DMA
Controller
Address Generator Units
Address Latch
Program Memory
EA MUX
Data Latch
ROM Latch
24
Control Signals
to Various Blocks
Instruction Reg
Literal Data
Instruction
Decode and
Control
16
16
16
17 x 17
Multiplier
Divide Support
16 x 16
W Register Array
16
16-bit ALU
16
To Peripheral Modules
DS70592B-page 26
Preliminary
 2009 Microchip Technology Inc.
PIC24HJXXXGPX06A/X08A/X10A
FIGURE 3-2:
PIC24HJXXXGPX06A/X08A/X10A PROGRAMMER’S MODEL
D15
D0
W0/WREG
PUSH.S Shadow
W1
DO Shadow
W2
W3
Legend
W4
W5
W6
W7
Working Registers
W8
W9
W10
W11
W12
W13
W14/Frame Pointer
W15/Stack Pointer
Stack Pointer Limit Register
SPLIM
PC22
PC0
Program Counter
0
0
7
Data Table Page Address
TBLPAG
7
0
PSVPAG
Program Space Visibility Page Address
15
0
RCOUNT
REPEAT Loop Counter
15
0
Core Configuration Register
CORCON
—
—
—
—
—
—
— DC
SRH
3.3
IPL2 IPL1 IPL0 RA
N
OV
Z
C
STATUS Register
SRL
CPU Control Registers
 2009 Microchip Technology Inc.
Preliminary
DS70592B-page 27
PIC24HJXXXGPX06A/X08A/X10A
REGISTER 3-1:
SR: CPU STATUS REGISTER
U-0
U-0
U-0
U-0
U-0
U-0
U-0
R/W-0
—
—
—
—
—
—
—
DC
bit 15
bit 8
R/W-0(1)
R/W-0(2)
R/W-0(2)
IPL<2:0>(2)
R-0
R/W-0
R/W-0
R/W-0
R/W-0
RA
N
OV
Z
C
bit 7
bit 0
Legend:
C = Clear only bit
R = Readable bit
U = Unimplemented bit, read as ‘0’
S = Set only bit
W = Writable bit
-n = Value at POR
‘1’ = Bit is set
‘0’ = Bit is cleared
x = Bit is unknown
bit 15-9
Unimplemented: Read as ‘0’
bit 8
DC: MCU ALU Half Carry/Borrow bit
1 = A carry-out from the 4th low-order bit (for byte sized data) or 8th low-order bit (for word sized data)
of the result occurred
0 = No carry-out from the 4th low-order bit (for byte sized data) or 8th low-order bit (for word sized
data) of the result occurred
bit 7-5
IPL<2:0>: CPU Interrupt Priority Level Status bits(2)
111 = CPU Interrupt Priority Level is 7 (15), user interrupts disabled
110 = CPU Interrupt Priority Level is 6 (14)
101 = CPU Interrupt Priority Level is 5 (13)
100 = CPU Interrupt Priority Level is 4 (12)
011 = CPU Interrupt Priority Level is 3 (11)
010 = CPU Interrupt Priority Level is 2 (10)
001 = CPU Interrupt Priority Level is 1 (9)
000 = CPU Interrupt Priority Level is 0 (8)
bit 4
RA: REPEAT Loop Active bit
1 = REPEAT loop in progress
0 = REPEAT loop not in progress
bit 3
N: MCU ALU Negative bit
1 = Result was negative
0 = Result was non-negative (zero or positive)
bit 2
OV: MCU ALU Overflow bit
This bit is used for signed arithmetic (2’s complement). It indicates an overflow of the magnitude which
causes the sign bit to change state.
1 = Overflow occurred for signed arithmetic (in this arithmetic operation)
0 = No overflow occurred
bit 1
Z: MCU ALU Zero bit
1 = An operation which affects the Z bit has set it at some time in the past
0 = The most recent operation which affects the Z bit has cleared it (i.e., a non-zero result)
bit 0
C: MCU ALU Carry/Borrow bit
1 = A carry-out from the Most Significant bit (MSb) of the result occurred
0 = No carry-out from the Most Significant bit of the result occurred
Note 1: The IPL<2:0> bits are concatenated with the IPL<3> bit (CORCON<3>) to form the CPU Interrupt Priority
Level. The value in parentheses indicates the IPL if IPL<3> = 1. User interrupts are disabled when
IPL<3> = 1.
2: The IPL<2:0> Status bits are read only when NSTDIS = 1 (INTCON1<15>).
DS70592B-page 28
Preliminary
 2009 Microchip Technology Inc.
PIC24HJXXXGPX06A/X08A/X10A
REGISTER 3-2:
CORCON: CORE CONTROL REGISTER
U-0
—
bit 15
U-0
—
U-0
—
U-0
—
U-0
—
U-0
—
U-0
—
U-0
—
U-0
—
U-0
—
bit 8
U-0
—
U-0
—
R/C-0
IPL3(1)
R/W-0
PSV
U-0
—
U-0
—
bit 7
bit 0
Legend:
R = Readable bit
0’ = Bit is cleared
bit 15-4
bit 3
bit 2
bit 1-0
C = Clear only bit
W = Writable bit
‘x = Bit is unknown
-n = Value at POR
‘1’ = Bit is set
U = Unimplemented bit, read as ‘0’
Unimplemented: Read as ‘0’
IPL3: CPU Interrupt Priority Level Status bit 3(1)
1 = CPU interrupt priority level is greater than 7
0 = CPU interrupt priority level is 7 or less
PSV: Program Space Visibility in Data Space Enable bit
1 = Program space visible in data space
0 = Program space not visible in data space
Unimplemented: Read as ‘0’
Note 1: The IPL3 bit is concatenated with the IPL<2:0> bits (SR<7:5>) to form the CPU interrupt priority level.
 2009 Microchip Technology Inc.
Preliminary
DS70592B-page 29
PIC24HJXXXGPX06A/X08A/X10A
3.4
3.4.2
Arithmetic Logic Unit (ALU)
The PIC24HJXXXGPX06A/X08A/X10A ALU is 16 bits
wide and is capable of addition, subtraction, bit shifts
and logic operations. Unless otherwise mentioned,
arithmetic operations are 2’s complement in nature.
Depending on the operation, the ALU may affect the
values of the Carry (C), Zero (Z), Negative (N),
Overflow (OV) and Digit Carry (DC) Status bits in the
SR register. The C and DC Status bits operate as
Borrow and Digit Borrow bits, respectively, for
subtraction operations.
The ALU can perform 8-bit or 16-bit operations,
depending on the mode of the instruction that is used.
Data for the ALU operation can come from the W register array, or data memory, depending on the addressing mode of the instruction. Likewise, output data from
the ALU can be written to the W register array or a data
memory location.
Refer to the “dsPIC30F/33F Programmer’s Reference
Manual” (DS70157) for information on the SR bits
affected by each instruction.
The
PIC24HJXXXGPX06A/X08A/X10A
CPU
incorporates hardware support for both multiplication
and division. This includes a dedicated hardware
multiplier and support hardware for 16-bit divisor
division.
3.4.1
MULTIPLIER
DIVIDER
The divide block supports 32-bit/16-bit and 16-bit/16-bit
signed and unsigned integer divide operations with the
following data sizes:
1.
2.
3.
4.
32-bit signed/16-bit signed divide
32-bit unsigned/16-bit unsigned divide
16-bit signed/16-bit signed divide
16-bit unsigned/16-bit unsigned divide
The quotient for all divide instructions ends up in W0
and the remainder in W1. Sixteen-bit signed and
unsigned DIV instructions can specify any W register
for both the 16-bit divisor (Wn) and any W register
(aligned) pair (W(m + 1):Wm) for the 32-bit dividend.
The divide algorithm takes one cycle per bit of divisor,
so both 32-bit/16-bit and 16-bit/16-bit instructions take
the same number of cycles to execute.
3.4.3
MULTI-BIT DATA SHIFTER
The multi-bit data shifter is capable of performing up to
16-bit arithmetic or logic right shifts, or up to 16-bit left
shifts in a single cycle. The source can be either a
working register or a memory location.
The shifter requires a signed binary value to determine
both the magnitude (number of bits) and direction of the
shift operation. A positive value shifts the operand right.
A negative value shifts the operand left. A value of ‘0’
does not modify the operand.
Using the high-speed 17-bit x 17-bit multiplier, the ALU
supports unsigned, signed or mixed-sign operation in
several multiplication modes:
1.
2.
3.
4.
5.
6.
7.
16-bit x 16-bit signed
16-bit x 16-bit unsigned
16-bit signed x 5-bit (literal) unsigned
16-bit unsigned x 16-bit unsigned
16-bit unsigned x 5-bit (literal) unsigned
16-bit unsigned x 16-bit signed
8-bit unsigned x 8-bit unsigned
DS70592B-page 30
Preliminary
 2009 Microchip Technology Inc.
PIC24HJXXXGPX06A/X08A/X10A
4.0
MEMORY ORGANIZATION
Note:
4.1
This data sheet summarizes the features
of the PIC24HJXXXGPX06A/X08A/X10A
family of devices. However, it is not
intended to be a comprehensive reference
source. To complement the information in
this data sheet, refer to Section 3. “Data
Memory” (DS70237) of the “dsPIC33F/
PIC24H Family Reference Manual”, which
is available from the Microchip website
(www.microchip.com).
The PIC24HJXXXGPX06A/X08A/X10A architecture
features separate program and data memory spaces
and buses. This architecture also allows the direct
access of program memory from the data space during
code execution.
FIGURE 4-1:
The program address memory space of the
PIC24HJXXXGPX06A/X08A/X10A devices is 4M instructions. The space is addressable by a 24-bit value derived
from either the 23-bit Program Counter (PC) during program execution, or from table operation or data space
remapping as described in Section 4.4 “Interfacing Program and Data Memory Spaces”.
User access to the program memory space is restricted
to the lower half of the address range (0x000000 to
0x7FFFFF). The exception is the use of TBLRD/TBLWT
operations, which use TBLPAG<7> to permit access to
the Configuration bits and Device ID sections of the
configuration memory space.
Memory maps for the PIC24HJXXXGPX06A/X08A/
X10A family of devices are shown in Figure 4-1.
PROGRAM MEMORY MAP FOR PIC24HJXXXGPX06A/X08A/X10A FAMILY DEVICES
PIC24HJ64XXXXXA
GOTO Instruction
Reset Address
Interrupt Vector Table
Reserved
Alternate Vector Table
User Memory Space
Program Address Space
User Program
Flash Memory
(22K instructions)
PIC24HJ128XXXXXA
GOTO Instruction
Reset Address
Interrupt Vector Table
Reserved
Alternate Vector Table
PIC24HJ256XXXXXA
GOTO Instruction
Reset Address
Interrupt Vector Table
Reserved
Alternate Vector Table
User Program
Flash Memory
(44K instructions)
User Program
Flash Memory
(88K instructions)
0x000000
0x000002
0x000004
0x0000FE
0x000100
0x000104
0x0001FE
0x000200
0x00ABFE
0x00AC00
0x0157FE
0x015800
Unimplemented
(Read ‘0’s)
Unimplemented
(Read ‘0’s)
0x02ABFE
0x02AC00
Unimplemented
(Read ‘0’s)
Configuration Memory Space
0x7FFFFE
0x800000
Reserved
Reserved
Reserved
Device Configuration
Registers
Device Configuration
Registers
Device Configuration
Registers
Reserved
Reserved
Reserved
DEVID (2)
DEVID (2)
DEVID (2)
 2009 Microchip Technology Inc.
Preliminary
0xF7FFFE
0xF80000
0xF80017
0xF80010
0xFEFFFE
0xFF0000
0xFFFFFE
DS70592B-page 31
PIC24HJXXXGPX06A/X08A/X10A
4.1.1
PROGRAM MEMORY
ORGANIZATION
4.1.2
All PIC24HJXXXGPX06A/X08A/X10A devices reserve
the addresses between 0x00000 and 0x000200 for
hard-coded program execution vectors. A hardware
Reset vector is provided to redirect code execution
from the default value of the PC on device Reset to the
actual start of code. A GOTO instruction is programmed
by the user at 0x000000, with the actual address for the
start of code at 0x000002.
The program memory space is organized in wordaddressable blocks. Although it is treated as 24 bits
wide, it is more appropriate to think of each address of
the program memory as a lower and upper word, with
the upper byte of the upper word being unimplemented.
The lower word always has an even address, while the
upper word has an odd address (Figure 4-2).
PIC24HJXXXGPX06A/X08A/X10A devices also have
two interrupt vector tables, located from 0x000004 to
0x0000FF and 0x000100 to 0x0001FF. These vector
tables allow each of the many device interrupt sources
to be handled by separate Interrupt Service Routines
(ISRs). A more detailed discussion of the interrupt vector tables is provided in Section 7.1 “Interrupt Vector
Table”.
Program memory addresses are always word-aligned
on the lower word, and addresses are incremented or
decremented by two during code execution. This
arrangement also provides compatibility with data
memory space addressing and makes it possible to
access data in the program memory space.
FIGURE 4-2:
msw
Address
PROGRAM MEMORY ORGANIZATION
16
8
PC Address
(lsw Address)
0
0x000000
0x000002
0x000004
0x000006
00000000
00000000
00000000
00000000
Program Memory
‘Phantom’ Byte
(read as ‘0’)
DS70592B-page 32
least significant word
most significant word
23
0x000001
0x000003
0x000005
0x000007
INTERRUPT AND TRAP VECTORS
Instruction Width
Preliminary
 2009 Microchip Technology Inc.
PIC24HJXXXGPX06A/X08A/X10A
4.2
Data Address Space
The PIC24HJXXXGPX06A/X08A/X10A CPU has a
separate 16-bit wide data memory space. The data
space is accessed using separate Address Generation
Units (AGUs) for read and write operations. Data memory maps of devices with different RAM sizes are
shown in Figure 4-3 and Figure 4-4.
All Effective Addresses (EAs) in the data memory space
are 16 bits wide and point to bytes within the data space.
This arrangement gives a data space address range of
64 Kbytes or 32K words. The lower half of the data
memory space (that is, when EA<15> = 0) is used for
implemented memory addresses, while the upper half
(EA<15> = 1) is reserved for the Program Space
Visibility area (see Section 4.4.3 “Reading Data from
Program Memory Using Program Space Visibility”).
PIC24HJXXXGPX06A/X08A/X10A devices implement
up to 16 Kbytes of data memory. Should an EA point to
a location outside of this area, an all-zero word or byte
will be returned.
4.2.1
DATA MEMORY ORGANIZATION
AND ALIGNMENT
To maintain backward compatibility with PIC® MCU
devices and improve data space memory usage
efficiency, the PIC24HJXXXGPX06A/X08A/X10A
instruction set supports both word and byte operations.
As a consequence of byte accessibility, all effective
address calculations are internally scaled to step
through word-aligned memory. For example, the core
recognizes that Post-Modified Register Indirect
Addressing mode [Ws++] will result in a value of Ws +
1 for byte operations and Ws + 2 for word operations.
Data byte reads will read the complete word that
contains the byte, using the Least Significant bit (LSb)
of any EA to determine which byte to select. The
selected byte is placed onto the Least Significant Byte
(LSB) of the data path. That is, data memory and registers are organized as two parallel byte-wide entities
with shared (word) address decode but separate write
lines. Data byte writes only write to the corresponding
side of the array or register which matches the byte
address.
 2009 Microchip Technology Inc.
All byte loads into any W register are loaded into the
Least Significant Byte. The Most Significant Byte
(MSB) is not modified.
A sign-extend instruction (SE) is provided to allow
users to translate 8-bit signed data to 16-bit signed
values. Alternatively, for 16-bit unsigned data, users
can clear the Most Significant Byte of any W register by
executing a zero-extend (ZE) instruction on the
appropriate address.
4.2.3
DATA SPACE WIDTH
The data memory space is organized in byte addressable, 16-bit wide blocks. Data is aligned in data
memory and registers as 16-bit words, but all data
space EAs resolve to bytes. The Least Significant
Bytes of each word have even addresses, while the
Most Significant Bytes have odd addresses.
4.2.2
All word accesses must be aligned to an even address.
Misaligned word data fetches are not supported, so
care must be taken when mixing byte and word operations, or translating from 8-bit MCU code. If a misaligned read or write is attempted, an address error
trap is generated. If the error occurred on a read, the
instruction underway is completed; if it occurred on a
write, the instruction will be executed but the write does
not occur. In either case, a trap is then executed, allowing the system and/or user to examine the machine
state prior to execution of the address Fault.
SFR SPACE
The first 2 Kbytes of the Near Data Space, from 0x0000
to 0x07FF, is primarily occupied by Special Function
Registers (SFRs). These are used by the
PIC24HJXXXGPX06A/X08A/X10A core and peripheral
modules for controlling the operation of the device.
SFRs are distributed among the modules that they
control, and are generally grouped together by module.
Much of the SFR space contains unused addresses;
these are read as ‘0’. A complete listing of implemented
SFRs, including their addresses, is shown in Table 4-1
through Table 4-33.
Note:
4.2.4
The actual set of peripheral features and
interrupts varies by the device. Please
refer to the corresponding device tables
and pinout diagrams for device-specific
information.
NEAR DATA SPACE
The 8-Kbyte area between 0x0000 and 0x1FFF is
referred to as the Near Data Space. Locations in this
space are directly addressable via a 13-bit absolute
address field within all memory direct instructions.
Additionally, the whole data space is addressable using
MOV instructions, which support Memory Direct
Addressing mode with a 16-bit address field, or by
using Indirect Addressing mode using a working
register as an Address Pointer.
Preliminary
DS70592B-page 33
PIC24HJXXXGPX06A/X08A/X10A
FIGURE 4-3:
DATA MEMORY MAP FOR PIC24HJXXXGPX06A/X08A/X10A DEVICES WITH 8 KBS
RAM
MSB
Address
MSB
2 Kbyte
SFR Space
LSB
Address
16 bits
LSB
0x0000
0x0001
SFR Space
0x07FE
0x0800
0x07FF
0x0801
8 Kbyte
Near
Data
Space
X Data RAM (X)
8 Kbyte
SRAM Space
0x1FFF
0x2001
0x27FF
0x2801
0x1FFE
0x2000
DMA RAM
0x8001
0x8000
X Data
Unimplemented (X)
Optionally
Mapped
into Program
Memory
0xFFFF
DS70592B-page 34
0x27FE
0x2800
0xFFFE
Preliminary
 2009 Microchip Technology Inc.
PIC24HJXXXGPX06A/X08A/X10A
FIGURE 4-4:
DATA MEMORY MAP FOR PIC24HJXXXGPX06A/X08A/X10A DEVICES WITH 16 KBS
RAM
MSB
Address
LSB
Address
16 bits
MSB
LSB
0x0000
0x0001
2 Kbyte
SFR Space
SFR Space
0x07FE
0x0800
0x07FF
0x0801
0x1FFF
8 Kbyte
Near
Data
Space
0x1FFE
X Data RAM (X)
16 Kbyte
SRAM Space
0x3FFF
0x4001
0x47FF
0x4801
0x3FFE
0x4000
DMA RAM
0x47FE
0x4800
0x8001
0x8000
X Data
Unimplemented (X)
Optionally
Mapped
into Program
Memory
0xFFFF
4.2.5
0xFFFE
DMA RAM
Every
PIC24HJXXXGPX06A/X08A/X10A
device
contains 2 Kbytes of dual ported DMA RAM located at
the end of data space. Memory locations in the DMA
RAM space are accessible simultaneously by the CPU
and the DMA controller module. DMA RAM is utilized by
the DMA controller to store data to be transferred to
various peripherals using DMA, as well as data
transferred from various peripherals using DMA. The
DMA RAM can be accessed by the DMA controller
without having to steal cycles from the CPU.
When the CPU and the DMA controller attempt to
concurrently write to the same DMA RAM location, the
hardware ensures that the CPU is given precedence in
accessing the DMA RAM location. Therefore, the DMA
RAM provides a reliable means of transferring DMA
data without ever having to stall the CPU.
Note:
 2009 Microchip Technology Inc.
Preliminary
DMA RAM can be used for general
purpose data storage if the DMA function
is not required in an application.
DS70592B-page 35
CPU CORE REGISTERS MAP
All
Resets
Preliminary
SFR Name
SFR
Addr
WREG0
0000
Working Register 0
0000
WREG1
0002
Working Register 1
0000
WREG2
0004
Working Register 2
0000
WREG3
0006
Working Register 3
0000
WREG4
0008
Working Register 4
0000
WREG5
000A
Working Register 5
0000
WREG6
000C
Working Register 6
0000
WREG7
000E
Working Register 7
0000
WREG8
0010
Working Register 8
0000
WREG9
0012
Working Register 9
0000
WREG10
0014
Working Register 10
0000
WREG11
0016
Working Register 11
0000
WREG12
0018
Working Register 12
0000
WREG13
001A
Working Register 13
0000
WREG14
001C
Working Register 14
0000
WREG15
001E
Working Register 15
0800
SPLIM
0020
Stack Pointer Limit Register
xxxx
PCL
002E
Program Counter Low Word Register
PCH
0030
—
—
—
—
—
—
—
—
Program Counter High Byte Register
0000
TBLPAG
0032
—
—
—
—
—
—
—
—
Table Page Address Pointer Register
0000
PSVPAG
0034
—
—
—
—
—
—
—
—
Program Memory Visibility Page Address Pointer Register
0000
RCOUNT
0036
SR
0042
—
—
—
—
—
—
—
DC
CORCON
0044
—
—
—
—
—
—
—
—
DISICNT
0052
—
—
BSRAM
0750
—
—
—
—
—
—
—
—
—
SSRAM
0752
—
—
—
—
—
—
—
—
—
 2009 Microchip Technology Inc.
Legend:
Bit 15
Bit 14
Bit 13
Bit 12
Bit 11
Bit 10
Bit 9
Bit 8
Bit 7
Bit 6
Bit 5
Bit 4
Bit 3
Bit 2
Bit 1
Bit 0
0000
Repeat Loop Counter Register
xxxx
IPL<2:0>
—
—
RA
N
OV
Z
C
0000
—
IPL3
PSV
—
—
0000
—
—
—
IW_BSR
IR_BSR
RL_BSR
0000
—
—
—
IW_SSR
IR_SSR
RL_SSR
0000
—
Disable Interrupts Counter Register
x = unknown value on Reset, — = unimplemented, read as ‘0’. Reset values are shown in hexadecimal for PinHigh devices.
xxxx
PIC24HJXXXGPX06A/X08A/X10A
DS70592B-page 36
TABLE 4-1:
 2009 Microchip Technology Inc.
TABLE 4-2:
CHANGE NOTIFICATION REGISTER MAP FOR PIC24HJXXXGPX10A DEVICES
SFR
Name
SFR
Addr
Bit 15
Bit 14
Bit 13
Bit 12
Bit 11
Bit 10
Bit 9
Bit 8
CNEN1
0060
CN15IE
CN14IE
CN13IE
CN12IE
CN11IE
CN10IE
CN9IE
CN8IE
CN7IE
CN6IE
CN5IE
CN4IE
CN3IE
CN2IE
CNEN2
0062
—
—
—
—
—
—
—
—
CN23IE
CN22IE
CN21IE
CN20IE
CN19IE
CN18IE
CNPU1
0068
CN8PUE
CN7PUE
CN6PUE
CN5PUE
CN4PUE
CN3PUE
CN2PUE
CN1PUE
CNPU2
006A
Legend:
CN15PUE CN14PUE CN13PUE CN12PUE CN11PUE CN10PUE CN9PUE
—
—
—
—
—
—
—
—
Bit 0
All
Resets
CN1IE
CN0IE
0000
CN17IE
CN16IE
0000
CN0PUE
0000
CN23PUE CN22PUE CN21PUE CN20PUE CN19PUE CN18PUE CN17PUE CN16PUE
0000
Bit 7
Bit 6
Bit 5
Bit 4
Bit 3
Bit 2
Bit 1
x = unknown value on Reset, — = unimplemented, read as ‘0’. Reset values are shown in hexadecimal for PinHigh devices.
CHANGE NOTIFICATION REGISTER MAP FOR PIC24HJXXXGPX08A DEVICES
SFR
Name
SFR
Addr
Bit 15
Bit 14
Bit 13
Bit 12
Bit 11
Bit 10
Bit 9
Bit 8
Bit 7
Bit 6
CNEN1
0060
CN15IE
CN14IE
CN13IE
CN12IE
CN11IE
CN10IE
CN9IE
CN8IE
CN7IE
CN6IE
CN5IE
CN4IE
CN3IE
CN2IE
CNEN2
0062
—
—
—
—
—
—
—
—
—
—
CN21IE
CN20IE
CN19IE
CN18IE
CNPU1
0068
CN8PUE
CN7PUE
CN6PUE
CN5PUE
CN4PUE
CN3PUE
CN2PUE
CN1PUE
CNPU2
006A
—
—
—
Preliminary
Legend:
CN15PUE CN14PUE CN13PUE CN12PUE CN11PUE CN10PUE CN9PUE
—
—
—
—
—
—
—
Bit 0
All
Resets
CN1IE
CN0IE
0000
CN17IE
CN16IE
0000
CN0PUE
0000
CN21PUE CN20PUE CN19PUE CN18PUE CN17PUE CN16PUE
0000
Bit 5
Bit 3
Bit 2
Bit 1
x = unknown value on Reset, — = unimplemented, read as ‘0’. Reset values are shown in hexadecimal.
TABLE 4-4:
CHANGE NOTIFICATION REGISTER MAP FOR PIC24HJXXXGPX06A DEVICES
SFR
Name
SFR
Addr
Bit 15
Bit 14
Bit 13
Bit 12
Bit 11
Bit 10
Bit 9
Bit 8
Bit 7
Bit 6
CNEN1
0060
CN15IE
CN14IE
CN13IE
CN12IE
CN11IE
CN10IE
CN9IE
CN8IE
CN7IE
CN6IE
CNEN2
0062
—
—
—
—
—
—
—
—
—
—
CNPU1
0068
CN8PUE
CN7PUE
CN6PUE
CN5PUE
CNPU2
006A
—
—
—
Legend:
Bit 4
CN15PUE CN14PUE CN13PUE CN12PUE CN11PUE CN10PUE CN9PUE
—
—
—
—
—
—
—
x = unknown value on Reset, — = unimplemented, read as ‘0’. Reset values are shown in hexadecimal.
Bit 5
Bit 0
All
Resets
CN1IE
CN0IE
0000
CN17IE
CN16IE
0000
CN0PUE
0000
CN18PUE CN17PUE CN16PUE
0000
Bit 4
Bit 3
CN5IE
CN4IE
CN3IE
CN2IE
CN21IE
CN20IE
—
CN18IE
CN4PUE
CN3PUE
CN2PUE
CN1PUE
CN21PUE CN20PUE
—
Bit 2
Bit 1
DS70592B-page 37
PIC24HJXXXGPX06A/X08A/X10A
TABLE 4-3:
SFR
Name
INTERRUPT CONTROLLER REGISTER MAP
SFR
Addr
Bit 15
Bit 14
Bit 13
Bit 12
Bit 11
Bit 10
Bit 9
Bit 8
Bit 7
Bit 6
Bit 5
Bit 4
Bit 3
Bit 2
Bit 1
Bit 0
All
Resets
INTCON1
0080
NSTDIS
—
—
—
—
—
—
—
—
OSCFAIL
—
0000
INTCON2
0082
ALTIVT
DISI
—
—
—
—
—
—
—
—
—
INT4EP
INT3EP
INT2EP
INT1EP
INT0EP
0000
IFS0
0084
—
DMA1IF
AD1IF
U1TXIF
U1RXIF
T3IF
T2IF
OC2IF
IC2IF
DMA0IF
T1IF
OC1IF
IC1IF
INT0IF
0000
IFS1
0086
U2TXIF
U2RXIF
INT2IF
T5IF
T4IF
OC4IF
OC3IF
DMA2IF
IC8IF
IC7IF
AD2IF
INT1IF
CNIF
—
MI2C1IF
SI2C1IF
0000
IFS2
0088
T6IF
DMA4IF
—
OC8IF
OC7IF
OC6IF
OC5IF
IC6IF
IC5IF
IC4IF
IC3IF
DMA3IF
C1IF
C1RXIF
SPI2IF
SPI2EIF
0000
IFS3
008A
—
—
DMA5IF
—
—
—
—
C2IF
C2RXIF
INT4IF
INT3IF
T9IF
T8IF
MI2C2IF
SI2C2IF
T7IF
0000
IFS4
008C
—
—
—
—
—
—
—
—
C2TXIF
C1TXIF
DMA7IF
DMA6IF
—
U2EIF
U1EIF
—
0000
IEC0
0094
—
DMA1IE
AD1IE
U1TXIE
U1RXIE
T3IE
T2IE
OC2IE
IC2IE
DMA0IE
T1IE
OC1IE
IC1IE
INT0IE
IEC1
0096
U2TXIE
U2RXIE
INT2IE
T5IE
T4IE
OC4IE
OC3IE
DMA2IE
IC8IE
IC7IE
AD2IE
INT1IE
CNIE
—
IEC2
0098
T6IE
DMA4IE
—
OC8IE
OC7IE
OC6IE
OC5IE
IC6IE
IC5IE
IC4IE
IC3IE
DMA3IE
C1IE
C1RXIE
SPI2IE
SPI2EIE
IEC3
009A
—
—
DMA5IE
—
—
—
—
C2IE
C2RXIE
INT4IE
INT3IE
T9IE
T8IE
MI2C2IE
SI2C2IE
T7IE
0000
IEC4
009C
—
—
—
—
—
—
—
—
C2TXIE
C1TXIE
DMA7IE
DMA6IE
—
U2EIE
U1EIE
—
0000
SPI1IF SPI1EIF
SPI1IE SPI1EIE
DIV0ERR DMACERR MATHERR ADDRERR STKERR
MI2C1IE SI2C1IE
0000
0000
0000
Preliminary
 2009 Microchip Technology Inc.
IPC0
00A4
—
T1IP<2:0>
—
OC1IP<2:0>
—
IC1IP<2:0>
—
INT0IP<2:0>
4444
IPC1
00A6
—
T2IP<2:0>
—
OC2IP<2:0>
—
IC2IP<2:0>
—
DMA0IP<2:0>
4444
IPC2
00A8
—
U1RXIP<2:0>
—
SPI1IP<2:0>
—
SPI1EIP<2:0>
—
T3IP<2:0>
4444
IPC3
00AA
—
—
DMA1IP<2:0>
—
AD1IP<2:0>
—
U1TXIP<2:0>
0444
IPC4
00AC
—
CNIP<2:0>
—
—
MI2C1IP<2:0>
—
SI2C1IP<2:0>
4044
IPC5
00AE
—
IC8IP<2:0>
—
IC7IP<2:0>
—
AD2IP<2:0>
—
INT1IP<2:0>
4444
IPC6
00B0
—
T4IP<2:0>
—
OC4IP<2:0>
—
OC3IP<2:0>
—
DMA2IP<2:0>
4444
IPC7
00B2
—
U2TXIP<2:0>
—
U2RXIP<2:0>
—
INT2IP<2:0>
—
T5IP<2:0>
4444
IPC8
00B4
—
C1IP<2:0>
—
C1RXIP<2:0>
—
SPI2IP<2:0>
—
SPI2EIP<2:0>
4444
IPC9
00B6
—
IC5IP<2:0>
—
IC4IP<2:0>
—
IC3IP<2:0>
—
DMA3IP<2:0>
4444
IPC10
00B8
—
OC7IP<2:0>
—
OC6IP<2:0>
—
OC5IP<2:0>
—
IC6IP<2:0>
4444
IPC11
00BA
—
T6IP<2:0>
—
DMA4IP<2:0>
—
—
OC8IP<2:0>
4404
IPC12
00BC
—
T8IP<2:0>
—
MI2C2IP<2:0>
—
SI2C2IP<2:0>
—
T7IP<2:0>
4444
IPC13
00BE
—
C2RXIP<2:0>
—
INT4IP<2:0>
—
INT3IP<2:0>
—
T9IP<2:0>
4444
IPC14
00C0
—
—
—
—
—
—
—
—
—
—
C2IP<2:0>
IPC15
00C2
—
—
—
—
—
—
—
—
—
DMA5IP<2:0>
—
—
—
—
IPC16
00C4
—
—
—
—
—
U2EIP<2:0>
—
U1EIP<2:0>
—
—
—
—
IPC17
00C6
—
—
C1TXIP<2:0>
—
DMA7IP<2:0>
—
INTTREG
00E0
—
Legend:
—
—
—
C2TXIP<2:0>
—
—
—
—
—
ILR<3:0>
—
—
—
—
—
—
x = unknown value on Reset, — = unimplemented, read as ‘0’. Reset values are shown in hexadecimal for PinHigh devices.
—
—
VECNUM<6:0>
DMA6IP<2:0>
0004
0040
0440
4444
0000
PIC24HJXXXGPX06A/X08A/X10A
DS70592B-page 38
TABLE 4-5:
 2009 Microchip Technology Inc.
TABLE 4-6:
SFR
Name
SFR
Addr
TIMER REGISTER MAP
Bit 15
Bit 14
Bit 13
Bit 12
Bit 11
Bit 10
Bit 9
Bit 8
Bit 7
TMR1
0100
Timer1 Register
PR1
0102
Period Register 1
T1CON
0104
TMR2
0106
TON
—
TSIDL
—
—
—
TMR3HLD 0108
—
—
—
Bit 6
Bit 5
Bit 4
Bit 3
Bit 2
Bit 1
Bit 0
All
Resets
xxxx
FFFF
TGATE
TCKPS<1:0>
—
TSYNC
TCS
—
0000
Timer2 Register
xxxx
Timer3 Holding Register (for 32-bit timer operations only)
xxxx
010A
Timer3 Register
xxxx
PR2
010C
Period Register 2
FFFF
PR3
010E
Period Register 3
T2CON
0110
TON
—
TSIDL
—
—
—
—
—
—
TGATE
TCKPS<1:0>
T32
—
TCS
—
0000
T3CON
0112
TON
—
TSIDL
—
—
—
—
—
—
TGATE
TCKPS<1:0>
—
—
TCS
—
0000
TMR4
0114
Timer4 Register
xxxx
TMR5HLD
0116
Timer5 Holding Register (for 32-bit operations only)
xxxx
TMR5
0118
Timer5 Register
xxxx
PR4
011A
Period Register 4
FFFF
PR5
011C
Period Register 5
T4CON
011E
TON
—
TSIDL
—
—
—
—
—
—
TGATE
TCKPS<1:0>
T32
—
TCS
—
0000
T5CON
0120
TON
—
TSIDL
—
—
—
—
—
—
TGATE
TCKPS<1:0>
—
—
TCS
—
0000
TMR6
0122
TMR7HLD 0124
FFFF
FFFF
Timer6 Register
xxxx
Timer7 Holding Register (for 32-bit operations only)
xxxx
TMR7
0126
Timer7 Register
xxxx
PR6
0128
Period Register 6
FFFF
PR7
012A
Period Register 7
T6CON
012C
TON
—
TSIDL
—
—
—
—
—
—
TGATE
TCKPS<1:0>
T32
—
TCS
—
0000
T7CON
012E
TON
—
TSIDL
—
—
—
—
—
—
TGATE
TCKPS<1:0>
—
—
TCS
—
0000
TMR8
0130
TMR9HLD 0132
FFFF
Timer8 Register
xxxx
DS70592B-page 39
Timer9 Holding Register (for 32-bit operations only)
xxxx
TMR9
0134
Timer9 Register
xxxx
PR8
0136
Period Register 8
FFFF
PR9
0138
Period Register 9
T8CON
013A
TON
—
TSIDL
—
—
—
—
—
—
TGATE
TCKPS<1:0>
T32
—
TCS
—
0000
T9CON
013C
TON
—
TSIDL
—
—
—
—
—
—
TGATE
TCKPS<1:0>
—
—
TCS
—
0000
Legend:
FFFF
x = unknown value on Reset, — = unimplemented, read as ‘0’. Reset values are shown in hexadecimal for PinHigh devices.
PIC24HJXXXGPX06A/X08A/X10A
Preliminary
TMR3
Preliminary
SFR Name
SFR
Addr
IC1BUF
0140
IC1CON
0142
IC2BUF
0144
IC2CON
0146
IC3BUF
0148
IC3CON
014A
IC4BUF
014C
IC4CON
014E
IC5BUF
0150
IC5CON
0152
IC6BUF
0154
IC6CON
0156
IC7BUF
0158
IC7CON
015A
IC8BUF
015C
IC8CON
015E
Legend:
INPUT CAPTURE REGISTER MAP
Bit 15
Bit 14
Bit 13
Bit 12
Bit 11
Bit 10
Bit 9
—
—
ICSIDL
—
—
—
—
Bit 8
Bit 7
Bit 6
Bit 5
Bit 4
Bit 3
Bit 2
Bit 1
ICI<1:0>
ICOV
ICBNE
ICM<2:0>
ICI<1:0>
ICOV
ICBNE
ICM<2:0>
ICI<1:0>
ICOV
ICBNE
ICM<2:0>
ICI<1:0>
ICOV
ICBNE
ICM<2:0>
ICI<1:0>
ICOV
ICBNE
ICM<2:0>
ICI<1:0>
ICOV
ICBNE
ICM<2:0>
ICI<1:0>
ICOV
ICBNE
ICM<2:0>
ICI<1:0>
ICOV
ICBNE
ICM<2:0>
Input 1 Capture Register
—
ICTMR
—
ICSIDL
—
—
—
—
—
ICTMR
—
ICSIDL
—
—
—
—
—
ICTMR
—
ICSIDL
—
—
—
—
—
ICTMR
—
ICSIDL
—
—
—
—
—
ICTMR
—
ICSIDL
—
—
—
—
—
ICTMR
—
ICSIDL
—
—
—
—
—
ICTMR
—
ICSIDL
—
—
—
—
—
ICTMR
0000
xxxx
Input 8 Capture Register
—
0000
xxxx
Input 7 Capture Register
—
0000
xxxx
Input 6 Capture Register
—
0000
xxxx
Input 5 Capture Register
—
0000
xxxx
Input 4 Capture Register
—
0000
xxxx
Input 3 Capture Register
—
All
Resets
xxxx
Input 2 Capture Register
—
Bit 0
0000
xxxx
x = unknown value on Reset, — = unimplemented, read as ‘0’. Reset values are shown in hexadecimal for PinHigh devices.
0000
PIC24HJXXXGPX06A/X08A/X10A
DS70592B-page 40
TABLE 4-7:
 2009 Microchip Technology Inc.
 2009 Microchip Technology Inc.
TABLE 4-8:
SFR Name
OUTPUT COMPARE REGISTER MAP
SFR
Addr
Bit 15
Bit 14
Bit 13
Bit 12
Bit 11
Bit 10
Bit 9
Bit 8
Bit 7
Bit 6
0180
Output Compare 1 Secondary Register
OC1R
0182
Output Compare 1 Register
OC1CON
0184
OC2RS
0186
Output Compare 2 Secondary Register
OC2R
0188
Output Compare 2 Register
OC2CON
018A
OC3RS
018C
Output Compare 3 Secondary Register
OC3R
018E
Output Compare 3 Register
OC3CON
0190
OC4RS
0192
Output Compare 4 Secondary Register
OC4R
0194
Output Compare 4 Register
OC4CON
0196
OC5RS
0198
Output Compare 5 Secondary Register
OC5R
019A
Output Compare 5 Register
OC5CON
019C
OC6RS
019E
Output Compare 6 Secondary Register
OC6R
01A0
Output Compare 6 Register
OC6CON
01A2
OC7RS
01A4
Output Compare 7 Secondary Register
OC7R
01A6
Output Compare 7 Register
OC7CON
01A8
OC8RS
01AA
Output Compare 8 Secondary Register
OC8R
01AC
Output Compare 8 Register
OC8CON
01AE
Legend:
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
OCSIDL
OCSIDL
OCSIDL
OCSIDL
OCSIDL
OCSIDL
OCSIDL
OCSIDL
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
Bit 4
Bit 3
Bit 2
Bit 1
Bit 0
All
Resets
xxxx
xxxx
—
OCFLT
OCTSEL
OCM<2:0>
0000
xxxx
xxxx
—
OCFLT
OCTSEL
OCM<2:0>
0000
xxxx
xxxx
—
OCFLT
OCTSEL
OCM<2:0>
0000
xxxx
xxxx
—
OCFLT
OCTSEL
OCM<2:0>
0000
xxxx
xxxx
—
OCFLT
OCTSEL
OCM<2:0>
0000
xxxx
xxxx
—
OCFLT
OCTSEL
OCM<2:0>
0000
xxxx
xxxx
—
OCFLT
OCTSEL
OCM<2:0>
0000
xxxx
xxxx
—
x = unknown value on Reset, — = unimplemented, read as ‘0’. Reset values are shown in hexadecimal for PinHigh devices.
OCFLT
OCTSEL
OCM<2:0>
0000
DS70592B-page 41
PIC24HJXXXGPX06A/X08A/X10A
Preliminary
OC1RS
Bit 5
I2C1 REGISTER MAP
SFR
Addr
Bit 15
Bit 14
Bit 13
Bit 12
Bit 11
Bit 10
Bit 9
Bit 8
I2C1RCV
0200
—
—
—
—
—
—
—
—
Receive Register
0000
I2C1TRN
0202
—
—
—
—
—
—
—
—
Transmit Register
00FF
I2C1BRG
0204
—
—
—
—
—
—
—
I2C1CON
0206
I2CEN
—
I2CSIDL
SCLREL
IPMIEN
A10M
DISSLW
SMEN
GCEN
STREN
ACKDT
ACKEN
RCEN
PEN
RSEN
SEN
1000
I2C1STAT
0208
ACKSTAT
TRSTAT
—
—
—
BCL
GCSTAT
ADD10
IWCOL
I2COV
D_A
P
S
R_W
RBF
TBF
0000
I2C1ADD
020A
—
—
—
—
—
—
Address Register
0000
I2C1MSK
020C
—
—
—
—
—
—
Address Mask Register
0000
SFR Name
Legend:
Bit 7
Bit 6
Bit 5
Bit 4
Bit 3
Bit 2
Bit 1
Bit 0
Baud Rate Generator Register
All
Resets
0000
x = unknown value on Reset, — = unimplemented, read as ‘0’. Reset values are shown in hexadecimal for PinHigh devices.
TABLE 4-10:
I2C2 REGISTER MAP
SFR
Addr
Bit 15
Bit 14
Bit 13
Bit 12
Bit 11
Bit 10
Bit 9
Bit 8
I2C2RCV
0210
—
—
—
—
—
—
—
—
Receive Register
0000
I2C2TRN
0212
—
—
—
—
—
—
—
—
Transmit Register
00FF
I2C2BRG
0214
—
—
—
—
—
—
—
I2C2CON
0216
I2CEN
—
I2CSIDL
SCLREL
IPMIEN
A10M
DISSLW
SMEN
GCEN
STREN
ACKDT
ACKEN
RCEN
PEN
RSEN
SEN
1000
I2C2STAT
0218
ACKSTAT
TRSTAT
—
—
—
BCL
GCSTAT
ADD10
IWCOL
I2COV
D_A
P
S
R_W
RBF
TBF
0000
I2C2ADD
021A
—
—
—
—
—
—
Address Register
0000
I2C2MSK
021C
—
—
—
—
—
—
Address Mask Register
0000
SFR Name
Preliminary
Legend:
Bit 7
Bit 6
Bit 5
Bit 4
Bit 3
Bit 2
Bit 1
Bit 0
Baud Rate Generator Register
All
Resets
0000
x = unknown value on Reset, — = unimplemented, read as ‘0’. Reset values are shown in hexadecimal for PinHigh devices.
TABLE 4-11:
UART1 REGISTER MAP
 2009 Microchip Technology Inc.
SFR Name
SFR
Addr
U1MODE
0220
UARTEN
U1STA
0222
UTXISEL1
U1TXREG
0224
—
—
U1RXREG
0226
—
—
U1BRG
0228
Legend:
x = unknown value on Reset, — = unimplemented, read as ‘0’. Reset values are shown in hexadecimal for PinHigh devices.
Bit 15
Bit 10
Bit 9
Bit 8
Bit 7
Bit 6
UEN1
UEN0
WAKE
LPBACK
UTXBF
TRMT
Bit 4
Bit 3
ABAUD
URXINV
BRGH
ADDEN
RIDLE
PERR
Bit 1
STSEL
0000
0110
—
USIDL
IREN
RTSMD
—
—
UTXBRK
UTXEN
—
—
—
—
—
UART Transmit Register
xxxx
—
—
—
—
—
UART Receive Register
0000
Baud Rate Generator Prescaler
Bit 2
URXDA
Bit 12
URXISEL<1:0>
Bit 5
All
Resets
Bit 13
UTXINV UTXISEL0
Bit 11
Bit 0
Bit 14
PDSEL<1:0>
FERR
OERR
0000
PIC24HJXXXGPX06A/X08A/X10A
DS70592B-page 42
TABLE 4-9:
 2009 Microchip Technology Inc.
TABLE 4-12:
SFR
Name
SFR
Addr
UART2 REGISTER MAP
Bit 15
Bit 14
Bit 13
Bit 12
Bit 11
Bit 10
Bit 9
Bit 8
Bit 7
Bit 6
WAKE
LPBACK
Bit 5
Bit 4
Bit 3
ABAUD
URXINV
BRGH
ADDEN
RIDLE
PERR
Bit 2
Bit 1
All
Resets
STSEL
0000
URXDA
0110
U2MODE
0230
UARTEN
—
USIDL
IREN
RTSMD
—
UEN1
UEN0
U2STA
0232
UTXISEL1
UTXINV
UTXISEL0
—
UTXBRK
UTXEN
UTXBF
TRMT
U2TXREG
0234
—
—
—
—
—
—
—
UART Transmit Register
xxxx
U2RXREG
0236
—
—
—
—
—
—
—
UART Receive Register
0000
U2BRG
0238
Legend:
x = unknown value on Reset, — = unimplemented, read as ‘0’. Reset values are shown in hexadecimal for PinHigh devices.
SFR
Name
0000
SPI1 REGISTER MAP
Preliminary
Bit 15
Bit 14
Bit 13
SPI1STAT
0240
SPIEN
—
SPISIDL
—
—
—
—
SPI1CON1
0242
—
—
—
DISSCK
DISSDO
MODE16
SMP
SPI1CON2
0244
FRMEN
SPIFSD
FRMPOL
—
—
—
—
—
SPI1BUF
0248
Legend:
x = unknown value on Reset, — = unimplemented, read as ‘0’. Reset values are shown in hexadecimal for PinHigh devices.
Bit 12
Bit 11
Bit 10
Bit 9
Bit 8
Bit 7
Bit 6
Bit 5
Bit 4
—
—
CKE
SSEN
SPIROV
—
—
CKP
MSTEN
—
—
—
Bit 3
Bit 2
Bit 1
Bit 0
All
Resets
—
—
SPITBF
SPIRBF
0000
SPRE<2:0>
—
—
PPRE<1:0>
—
FRMDLY
—
SPI1 Transmit and Receive Buffer Register
0000
0000
0000
SPI2 REGISTER MAP
SFR
Addr
Bit 15
Bit 14
Bit 13
SPI2STAT
0260
SPIEN
—
SPISIDL
—
—
—
—
SPI2CON1
0262
—
—
—
DISSCK
DISSDO
MODE16
SMP
SPI2CON2
0264
FRMEN
SPIFSD
FRMPOL
—
—
—
—
—
SPI2BUF
0268
Legend:
x = unknown value on Reset, — = unimplemented, read as ‘0’. Reset values are shown in hexadecimal for PinHigh devices.
SFR Name
OERR
Baud Rate Generator Prescaler
SFR
Addr
TABLE 4-14:
FERR
Bit 12
Bit 11
Bit 10
Bit 9
Bit 8
Bit 7
Bit 6
Bit 5
Bit 4
—
—
CKE
SSEN
SPIROV
—
—
CKP
MSTEN
—
—
—
SPI2 Transmit and Receive Buffer Register
Bit 3
Bit 2
Bit 1
Bit 0
All
Resets
—
—
SPITBF
SPIRBF
0000
SPRE<2:0>
—
—
PPRE<1:0>
—
FRMDLY
—
0000
0000
0000
DS70592B-page 43
PIC24HJXXXGPX06A/X08A/X10A
TABLE 4-13:
URXISEL<1:0>
PDSEL<1:0>
Bit 0
File Name
ADC1 REGISTER MAP
Addr
ADC1BUF0
0300
AD1CON1
0320
AD1CON2
0322
Bit 15
Bit 14
Bit 13
Bit 12
Bit 11
Bit 10
Bit 9
Bit 8
ADON
—
ADSIDL
ADDMABM
—
AD12B
FORM<1:0>
—
—
CSCNA
CHPS<1:0>
—
—
Bit 7
Bit 6
Bit 5
Bit 3
Bit 2
Bit 1
Bit 0
—
SIMSAM
ASAM
SAMP
DONE
0000
BUFM
ALTS
0000
CH123SA
0000
ADC Data Buffer 0
VCFG<2:0>
AD1CON3
0324
ADRC
—
—
AD1CHS123
0326
—
—
—
—
xxxx
SSRC<2:0>
BUFS
—
CH123SB
—
—
SMPI<3:0>
SAMC<4:0>
ADCS<7:0>
CH123NB<1:0>
All
Resets
Bit 4
—
—
—
0000
CH123NA<1:0>
Preliminary
AD1CHS0
0328
CH0NB
CH0NA
—
—
AD1PCFGH(1)
032A
PCFG31 PCFG30
PCFG29
PCFG28
PCFG27 PCFG26 PCFG25
PCFG24
PCFG23
PCFG22
PCFG21
PCFG20
PCFG19 PCFG18 PCFG17
AD1PCFGL
032C
PCFG15 PCFG14
PCFG13
PCFG12
PCFG11 PCFG10
PCFG9
PCFG8
PCFG7
PCFG6
PCFG5
PCFG4
PCFG3
PCFG2
AD1CSSH(1)
032E
CSS31
CSS30
CSS29
CSS28
CSS27
CSS26
CSS25
CSS24
CSS23
CSS22
CSS21
CSS20
CSS19
AD1CSSL
0330
CSS15
CSS14
CSS13
CSS12
CSS11
CSS10
CSS9
CSS8
CSS7
CSS6
CSS5
CSS4
CSS3
AD1CON4
0332
—
—
—
—
—
—
—
—
—
—
—
—
—
Reserved
0334033E
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
0000
Bit 5
Bit 4
Bit 3
Bit 2
Bit 1
Bit 0
All
Resets
—
SIMSAM
ASAM
SAMP
DONE
0000
BUFM
ALTS
0000
Legend:
Note 1:
—
CH0SB<4:0>
0000
PCFG16
0000
PCFG1
PCFG0
0000
CSS18
CSS17
CSS16
0000
CSS2
CSS1
CSS0
DMABL<2:0>
0000
0000
x = unknown value on Reset, — = unimplemented, read as ‘0’. Reset values are shown in hexadecimal for PinHigh devices.
Not all ANx inputs are available on all devices. See the device pin diagrams for available ANx inputs.
TABLE 4-16:
File Name
Addr
ADC2BUF0
0340
AD2CON1
0360
AD2CON2
0362
ADC2 REGISTER MAP
Bit 15
Bit 14
Bit 13
Bit 12
Bit 11
Bit 10
ADON
—
ADSIDL
ADDMABM
—
AD12B
FORM<1:0>
Bit 9
Bit 8
—
—
CSCNA
CHPS<1:0>
—
Bit 7
Bit 6
ADC Data Buffer 0
VCFG<2:0>
 2009 Microchip Technology Inc.
AD2CON3
0364
ADRC
—
—
AD2CHS123
0366
—
—
—
—
AD2CHS0
0368
CH0NB
—
—
—
Reserved
036A
—
—
—
—
AD2PCFGL
036C
PCFG13
PCFG12
Reserved
036E
—
—
—
—
—
—
AD2CSSL
0370
CSS15
CSS14
CSS13
CSS12
CSS11
AD2CON4
0372
—
—
—
—
Reserved
0374037E
—
—
—
—
Legend:
CH0SA<4:0>
PCFG15 PCFG14
xxxx
SSRC<2:0>
BUFS
—
SMPI<3:0>
—
—
—
—
CH0NA
—
—
—
SAMC<4:0>
ADCS<7:0>
CH123NB<1:0>
CH123SB
CH0SB<3:0>
—
—
—
0000
CH123NA<1:0>
CH123SA
0000
CH0SA<3:0>
0000
—
—
—
—
—
—
—
—
—
—
0000
PCFG9
PCFG8
PCFG7
PCFG6
PCFG5
PCFG4
PCFG3
PCFG2
PCFG1
PCFG0
0000
—
—
—
—
—
—
—
—
—
—
0000
CSS10
CSS9
CSS8
CSS7
CSS6
CSS5
CSS4
CSS3
CSS2
CSS1
CSS0
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
PCFG11 PCFG10
x = unknown value on Reset, — = unimplemented, read as ‘0’. Reset values are shown in hexadecimal for PinHigh devices.
DMABL<2:0>
—
—
0000
0000
—
0000
PIC24HJXXXGPX06A/X08A/X10A
DS70592B-page 44
TABLE 4-15:
 2009 Microchip Technology Inc.
TABLE 4-17:
File Name Addr
DMA REGISTER MAP
Bit 15
Bit 14
Bit 13
Bit 12
Bit 11
Bit 10
Bit 9
Bit 8
Bit 7
Bit 6
DMA0CON 0380
CHEN
SIZE
DIR
HALF
NULLW
—
—
—
—
—
DMA0REQ 0382
FORCE
—
—
—
—
—
—
—
—
Bit 5
Bit 4
AMODE<1:0>
Bit 3
Bit 2
—
—
Bit 1
Bit 0
MODE<1:0>
IRQSEL<6:0>
All
Resets
0000
0000
DMA0STA
0384
STA<15:0>
0000
DMA0STB
0386
STB<15:0>
0000
DMA0PAD
0388
PAD<15:0>
DMA0CNT
038A
—
—
—
—
—
DMA1CON 038C
CHEN
SIZE
DIR
HALF
NULLW
—
—
—
—
DMA1REQ 038E
FORCE
—
—
—
—
—
—
—
—
0000
CNT<9:0>
—
AMODE<1:0>
0000
—
—
MODE<1:0>
IRQSEL<6:0>
0000
0000
DMA1STA
0390
STA<15:0>
0000
DMA1STB
0392
STB<15:0>
0000
DMA1PAD
0394
PAD<15:0>
DMA1CNT
0396
Preliminary
—
—
—
—
—
—
DMA2CON 0398
CHEN
SIZE
DIR
HALF
NULLW
—
—
—
—
DMA2REQ 039A
FORCE
—
—
—
—
—
—
—
—
0000
CNT<9:0>
—
AMODE<1:0>
0000
—
—
MODE<1:0>
IRQSEL<6:0>
0000
0000
DMA2STA
039C
STA<15:0>
0000
DMA2STB
039E
STB<15:0>
0000
DMA2PAD
03A0
PAD<15:0>
DMA2CNT
03A2
—
—
—
—
—
—
DMA3CON 03A4
CHEN
SIZE
DIR
HALF
NULLW
—
—
—
—
DMA3REQ 03A6
FORCE
—
—
—
—
—
—
—
—
0000
CNT<9:0>
—
AMODE<1:0>
0000
—
—
MODE<1:0>
IRQSEL<6:0>
0000
0000
DMA3STA
03A8
STA<15:0>
0000
DMA3STB
03AA
STB<15:0>
0000
DMA3PAD 03AC
PAD<15:0>
DMA3CNT 03AE
—
—
—
—
—
—
DMA4CON 03B0
CHEN
SIZE
DIR
HALF
NULLW
—
—
—
—
DMA4REQ 03B2
FORCE
—
—
—
—
—
—
—
—
0000
CNT<9:0>
—
AMODE<1:0>
0000
—
—
MODE<1:0>
IRQSEL<6:0>
0000
0000
DMA4STA
03B4
STA<15:0>
0000
DMA4STB
03B6
STB<15:0>
0000
DMA4PAD
03B8
PAD<15:0>
DS70592B-page 45
DMA4CNT 03BA
—
—
—
—
—
—
DMA5CON 03BC
CHEN
SIZE
DIR
HALF
NULLW
—
—
—
—
DMA5REQ 03BE
FORCE
—
—
—
—
—
—
—
—
0000
CNT<9:0>
—
AMODE<1:0>
0000
—
IRQSEL<6:0>
—
MODE<1:0>
0000
0000
DMA5STA
03C0
STA<15:0>
0000
DMA5STB
03C2
STB<15:0>
0000
Legend:
— = unimplemented, read as ‘0’. Reset values are shown in hexadecimal for PinHigh devices.
PIC24HJXXXGPX06A/X08A/X10A
—
File Name Addr
DMA REGISTER MAP (CONTINUED)
Bit 15
Bit 14
Bit 13
Bit 12
Bit 11
Bit 10
DMA5CNT 03C6
—
—
—
—
—
—
DMA6CON 03C8
CHEN
SIZE
DIR
HALF
NULLW
—
—
—
—
—
—
—
—
—
—
—
—
DMA5PAD
Bit 9
Bit 8
03C4
Bit 7
Bit 6
Bit 5
Bit 4
Bit 3
Bit 2
Bit 1
Bit 0
PAD<15:0>
DMA6REQ 03CA FORCE
All
Resets
0000
CNT<9:0>
—
0000
AMODE<1:0>
—
—
MODE<1:0>
IRQSEL<6:0>
0000
0000
DMA6STA
03CC
STA<15:0>
0000
DMA6STB
03CE
STB<15:0>
0000
DMA6PAD
03D0
PAD<15:0>
DMA6CNT 03D2
—
—
—
—
—
—
DMA7CON 03D4
CHEN
SIZE
DIR
HALF
NULLW
—
—
—
—
DMA7REQ 03D6
FORCE
—
—
—
—
—
—
—
—
0000
CNT<9:0>
—
0000
AMODE<1:0>
—
—
MODE<1:0>
IRQSEL<6:0>
0000
0000
DMA7STA
03D8
STA<15:0>
0000
DMA7STB
03DA
STB<15:0>
0000
DMA7PAD 03DC
PAD<15:0>
DMA7CNT 03DE
—
—
—
—
—
CNT<9:0>
Preliminary
DMACS0
03E0 PWCOL7 PWCOL6 PWCOL5 PWCOL4 PWCOL3 PWCOL2 PWCOL1 PWCOL0
DMACS1
03E2
DSADR
03E4
Legend:
—
—
—
XWCOL7
LSTCH<3:0>
XWCOL6 XWCOL5
PPST7
PPST6
0000
XWCOL4
XWCOL3
XWCOL2
PPST4
PPST3
PPST2
PPST5
XWCOL1 XWCOL0
PPST1
PPST0
DSADR<15:0>
0000
0000
0000
— = unimplemented, read as ‘0’. Reset values are shown in hexadecimal for PinHigh devices.
TABLE 4-18:
File Name
—
0000
—
ECAN1 REGISTER MAP WHEN C1CTRL1.WIN = 0 OR 1 FOR PIC24HJXXXGP506A/510A/610A DEVICES ONLY
Addr
Bit 15
Bit 14
Bit 13
Bit 12
Bit 11
C1CTRL1
0400
—
—
CSIDL
ABAT
—
C1CTRL2
0402
—
—
—
—
—
—
—
—
—
—
 2009 Microchip Technology Inc.
C1VEC
0404
C1FCTRL
0406
C1FIFO
0408
—
—
DMABS<2:0>
Bit 10
Bit 9
Bit 8
Bit 7
—
—
—
—
—
REQOP<2:0>
—
Bit 5
OPMODE<2:0>
FILHIT<4:0>
—
Bit 6
—
—
—
—
—
—
—
Bit 4
Bit 3
—
CANCAP
Bit 1
Bit 0
—
—
WIN
DNCNT<4:0>
—
FBP<5:0>
Bit 2
All
Resets
0480
0000
ICODE<6:0>
0000
0000
FSA<4:0>
FNRB<5:0>
0000
C1INTF
040A
—
—
TXBO
TXBP
RXBP
TXWAR
RXWAR
EWARN
IVRIF
WAKIF
ERRIF
—
FIFOIF
RBOVIF
RBIF
TBIF
0000
C1INTE
040C
—
—
—
—
—
—
—
—
IVRIE
WAKIE
ERRIE
—
FIFOIE
RBOVIE
RBIE
TBIE
0000
C1EC
040E
C1CFG1
0410
—
—
—
—
—
C1CFG2
0412
—
WAKFIL
—
—
—
C1FEN1
0414 FLTEN15 FLTEN14 FLTEN13 FLTEN12 FLTEN11 FLTEN10
TERRCNT<7:0>
RERRCNT<7:0>
—
—
—
SEG2PH<2:0>
FLTEN9
FLTEN8
SJW<1:0>
SEG2PHTS
SAM
FLTEN7
FLTEN6
0000
BRP<5:0>
SEG1PH<2:0>
FLTEN5
FLTEN4
0000
PRSEG<2:0>
FLTEN3
FLTEN2
FLTEN1
FLTEN0
0000
FFFF
C1FMSKSEL1 0418
F7MSK<1:0>
F6MSK<1:0>
F5MSK<1:0>
F4MSK<1:0>
F3MSK<1:0>
F2MSK<1:0>
F1MSK<1:0>
F0MSK<1:0>
0000
C1FMSKSEL2 041A
F15MSK<1:0>
F14MSK<1:0>
F13MSK<1:0>
F12MSK<1:0>
F11MSK<1:0>
F10MSK<1:0>
F9MSK<1:0>
F8MSK<1:0>
0000
Legend:
— = unimplemented, read as ‘0’. Reset values are shown in hexadecimal for PinHigh devices.
PIC24HJXXXGPX06A/X08A/X10A
DS70592B-page 46
TABLE 4-17:
 2009 Microchip Technology Inc.
TABLE 4-19:
File Name
ECAN1 REGISTER MAP WHEN C1CTRL1.WIN = 0 FOR PIC24HJXXXGP506A/510A/610A DEVICES ONLY
Addr
Bit 15
Bit 14
Bit 13
Bit 12
Bit 11
Bit 10
Bit 9
0400041E
Bit 8
Bit 7
Bit 5
Bit 4
Bit 3
Bit 2
Bit 1
Bit 0
All
Resets
RXFUL5
RXFUL4
RXFUL3
RXFUL2
RXFUL1
Bit 6
See definition when WIN = x
0420 RXFUL15 RXFUL14 RXFUL13 RXFUL12 RXFUL11 RXFUL10 RXFUL9
RXFUL0
0000
C1RXFUL2
0422 RXFUL31 RXFUL30 RXFUL29 RXFUL28 RXFUL27 RXFUL26 RXFUL25 RXFUL24 RXFUL23 RXFUL22 RXFUL21 RXFUL20 RXFUL19 RXFUL18 RXFUL17 RXFUL16
0000
C1RXOVF1
0428 RXOVF15 RXOVF14 RXOVF13 RXOVF12 RXOVF11 RXOVF10 RXOVF9
RXOVF0
0000
C1RXOVF2
042A RXOVF31 RXOVF30 RXOVF29 RXOVF28 RXOVF27 RXOVF26 RXOVF25 RXOVF24 RXOVF23 RXOVF22 RXOVF21 RXOVF20 RXOVF19 RXOVF18 RXOVF17 RXOVF16
0000
C1TR01CO
N
0430
TXEN1
TX
ABT1
TX
LARB1
TX
ERR1
TX
REQ1
RTREN1
TX1PRI<1:0>
TXEN0
TX
ABAT0
TX
LARB0
TX
ERR0
TX
REQ0
RTREN0
TX0PRI<1:0>
0000
C1TR23CO
N
0432
TXEN3
TX
ABT3
TX
LARB3
TX
ERR3
TX
REQ3
RTREN3
TX3PRI<1:0>
TXEN2
TX
ABAT2
TX
LARB2
TX
ERR2
TX
REQ2
RTREN2
TX2PRI<1:0>
0000
C1TR45CO
N
0434
TXEN5
TX
ABT5
TX
LARB5
TX
ERR5
TX
REQ5
RTREN5
TX5PRI<1:0>
TXEN4
TX
ABAT4
TX
LARB4
TX
ERR4
TX
REQ4
RTREN4
TX4PRI<1:0>
0000
C1TR67CO
N
0436
TXEN7
TX
ABT7
TX
LARB7
TX
ERR7
TX
REQ7
RTREN7
TX7PRI<1:0>
TXEN6
TX
ABAT6
TX
LARB6
TX
ERR6
TX
REQ6
RTREN6
TX6PRI<1:0>
xxxx
C1RXD
0440
Recieved Data Word
xxxx
C1TXD
0442
Transmit Data Word
xxxx
Legend:
RXOVF8
RXFUL7
RXOVF7
RXFUL6
RXOVF6
RXOVF5
RXOVF4
RXOVF3
RXOVF2
RXOVF1
x = unknown value on Reset, — = unimplemented, read as ‘0’. Reset values are shown in hexadecimal for PinHigh devices.
TABLE 4-20:
File Name
RXFUL8
ECAN1 REGISTER MAP WHEN C1CTRL1.WIN = 1 FOR PIC24HJXXXGP506A/510A/610A DEVICES ONLY
Addr
Bit 15
Bit 14
Bit 13
Bit 12
Bit 11
Bit 10
Bit 9
0400041E
Bit 8
Bit 7
Bit 6
Bit 5
Bit 4
Bit 3
Bit 2
Bit 1
Bit 0
All
Resets
See definition when WIN = x
DS70592B-page 47
C1BUFPNT1
0420
F3BP<3:0>
F2BP<3:0>
F1BP<3:0>
F0BP<3:0>
0000
C1BUFPNT2
0422
F7BP<3:0>
F6BP<3:0>
F5BP<3:0>
F4BP<3:0>
0000
C1BUFPNT3
0424
F11BP<3:0>
F10BP<3:0>
F9BP<3:0>
F8BP<3:0>
0000
C1BUFPNT4
0426
F15BP<3:0>
F14BP<3:0>
F13BP<3:0>
F12BP<3:0>
0000
C1RXM0SID
0430
SID<10:3>
—
EID<17:16>
xxxx
C1RXM0EID
0432
EID<15:8>
C1RXM1SID
0434
SID<10:3>
—
EID<17:16>
C1RXM1EID
0436
EID<15:8>
C1RXM2SID
0438
SID<10:3>
—
EID<17:16>
C1RXM2EID
043A
EID<15:8>
C1RXF0SID
0440
SID<10:3>
—
EID<17:16>
C1RXF0EID
0442
EID<15:8>
C1RXF1SID
0444
SID<10:3>
—
EID<17:16>
Legend:
SID<2:0>
—
MIDE
EID<7:0>
SID<2:0>
—
MIDE
xxxx
EID<7:0>
SID<2:0>
—
MIDE
xxxx
EID<7:0>
SID<2:0>
—
EXIDE
x = unknown value on Reset, — = unimplemented, read as ‘0’. Reset values are shown in hexadecimal for PinHigh devices.
—
EXIDE
xxxx
xxxx
EID<7:0>
SID<2:0>
xxxx
xxxx
xxxx
xxxx
PIC24HJXXXGPX06A/X08A/X10A
Preliminary
C1RXFUL1
File Name
ECAN1 REGISTER MAP WHEN C1CTRL1.WIN = 1 FOR PIC24HJXXXGP506A/510A/610A DEVICES ONLY (CONTINUED)
Addr
Bit 15
Bit 14
Bit 13
Bit 12
Bit 11
Preliminary
 2009 Microchip Technology Inc.
C1RXF1EID
0446
EID<15:8>
C1RXF2SID
0448
SID<10:3>
C1RXF2EID
044A
EID<15:8>
C1RXF3SID
044C
SID<10:3>
C1RXF3EID
044E
EID<15:8>
C1RXF4SID
0450
SID<10:3>
C1RXF4EID
0452
EID<15:8>
C1RXF5SID
0454
SID<10:3>
C1RXF5EID
0456
EID<15:8>
C1RXF6SID
0458
SID<10:3>
C1RXF6EID
045A
EID<15:8>
C1RXF7SID
045C
SID<10:3>
C1RXF7EID
045E
EID<15:8>
C1RXF8SID
0460
SID<10:3>
C1RXF8EID
0462
EID<15:8>
C1RXF9SID
0464
SID<10:3>
C1RXF9EID
0466
EID<15:8>
C1RXF10SID
0468
SID<10:3>
C1RXF10EID
046A
EID<15:8>
C1RXF11SID
046C
SID<10:3>
C1RXF11EID
046E
EID<15:8>
C1RXF12SID
0470
SID<10:3>
C1RXF12EID
0472
EID<15:8>
C1RXF13SID
0474
SID<10:3>
C1RXF13EID
0476
EID<15:8>
C1RXF14SID
0478
SID<10:3>
C1RXF14EID
047A
EID<15:8>
C1RXF15SID
047C
SID<10:3>
C1RXF15EID
047E
EID<15:8>
Legend:
Bit 10
Bit 9
Bit 8
Bit 7
Bit 6
Bit 5
Bit 4
Bit 3
Bit 2
Bit 1
Bit 0
EID<7:0>
SID<2:0>
—
EXIDE
xxxx
—
EID<17:16>
—
EID<17:16>
—
EID<17:16>
—
EID<17:16>
—
EID<17:16>
—
EID<17:16>
—
EID<17:16>
—
EID<17:16>
—
EID<17:16>
—
EID<17:16>
—
EID<17:16>
—
EID<17:16>
—
EID<17:16>
—
EID<17:16>
EID<7:0>
SID<2:0>
—
EXIDE
—
EXIDE
—
EXIDE
—
EXIDE
—
EXIDE
—
EXIDE
—
EXIDE
—
EXIDE
—
EXIDE
—
EXIDE
—
EXIDE
—
EXIDE
x = unknown value on Reset, — = unimplemented, read as ‘0’. Reset values are shown in hexadecimal for PinHigh devices.
—
EXIDE
EID<7:0>
xxxx
xxxx
EID<7:0>
SID<2:0>
xxxx
xxxx
EID<7:0>
SID<2:0>
xxxx
xxxx
EID<7:0>
SID<2:0>
xxxx
xxxx
EID<7:0>
SID<2:0>
xxxx
xxxx
EID<7:0>
SID<2:0>
xxxx
xxxx
EID<7:0>
SID<2:0>
xxxx
xxxx
EID<7:0>
SID<2:0>
xxxx
xxxx
EID<7:0>
SID<2:0>
xxxx
xxxx
EID<7:0>
SID<2:0>
xxxx
xxxx
EID<7:0>
SID<2:0>
xxxx
xxxx
EID<7:0>
SID<2:0>
xxxx
xxxx
EID<7:0>
SID<2:0>
All
Resets
xxxx
xxxx
xxxx
xxxx
PIC24HJXXXGPX06A/X08A/X10A
DS70592B-page 48
TABLE 4-20:
 2009 Microchip Technology Inc.
TABLE 4-21:
File Name
ECAN2 REGISTER MAP WHEN C2CTRL1.WIN = 0 OR 1 FOR PIC24HJ256GP610A DEVICES ONLY
Bit 15
Bit 14
Bit 13
Bit 12
Bit 11
C2CTRL1
0500
—
—
CSIDL
ABAT
—
C2CTRL2
0502
—
—
—
—
—
C2VEC
0504
—
—
—
C2FCTRL
0506
C2FIFO
0508
—
—
C2INTF
050A
—
—
TXBO
C2INTE
050C
—
—
—
C2EC
050E
Bit 10
Bit 9
Bit 8
Bit 7
—
—
REQOP<2:0>
—
—
—
—
—
—
TXWAR
—
—
—
Bit 3
—
CANCAP
—
RXWAR EWARN
—
—
Bit 2
Bit 1
Bit 0
All
Resets
—
—
WIN
0480
DNCNT<4:0>
0000
ICODE<6:0>
—
—
—
—
IVRIF
WAKIF
ERRIF
IVRIE
WAKIE
ERRIE
FBP<5:0>
RXBP
—
Bit 4
—
—
TXBP
Bit 5
OPMODE<2:0>
FILHIT<4:0>
DMABS<2:0>
Bit 6
—
0000
0000
FSA<4:0>
FNRB<5:0>
TERRCNT<7:0>
0000
—
FIFOIF
RBOVIF
RBIF
TBIF
—
FIFOIE
RBOVIE
RBIE
TBIE
RERRCNT<7:0>
0000
0000
0000
C2CFG1
0510
—
—
—
—
—
C2CFG2
0512
—
WAKFIL
—
—
—
SEG2PH<2:0>
SEG2PHTS
C2FEN1
0514
FLTEN15
FLTEN14
FLTEN13
FLTEN12
FLTEN11
FLTEN10 FLTEN9 FLTEN8
FLTEN7
C2FMSKSEL1
0518
F7MSK<1:0>
F6MSK<1:0>
F5MSK<1:0>
F4MSK<1:0>
F3MSK<1:0>
F2MSK<1:0>
F1MSK<1:0>
F0MSK<1:0>
0000
C2FMSKSEL2
051A
F15MSK<1:0>
F14MSK<1:0>
F13MSK<1:0>
F12MSK<1:0>
F11MSK<1:0>
F10MSK<1:0>
F9MSK<1:0>
F8MSK<1:0>
0000
Preliminary
Legend:
—
—
SJW<1:0>
BRP<5:0>
SAM
SEG1PH<2:0>
0000
PRSEG<2:0>
FLTEN6 FLTEN5 FLTEN4 FLTEN3
FLTEN2 FLTEN1
0000
FLTEN0
FFFF
— = unimplemented, read as ‘0’. Reset values are shown in hexadecimal for PinHigh devices.
TABLE 4-22:
File Name
—
Addr
ECAN2 REGISTER MAP WHEN C2CTRL1.WIN = 0 FOR PIC24HJ256GP610A DEVICES ONLY
Bit 15
Bit 14
Bit 13
Bit 12
Bit 11
Bit 10
0500051E
Bit 9
Bit 8
Bit 7
Bit 5
Bit 4
Bit 3
Bit 2
Bit 1
Bit 0
All
Resets
RXFUL5
RXFUL4
RXFUL3
RXFUL2
RXFUL1
Bit 6
See definition when WIN = x
C2RXFUL1
0520 RXFUL15 RXFUL14 RXFUL13 RXFUL12 RXFUL11 RXFUL10
RXFUL0
0000
C2RXFUL2
0522 RXFUL31 RXFUL30 RXFUL29 RXFUL28 RXFUL27 RXFUL26 RXFUL25 RXFUL24 RXFUL23 RXFUL22 RXFUL21 RXFUL20 RXFUL19 RXFUL18 RXFUL17 RXFUL16
RXFUL9
RXFUL8
RXFUL7
RXFUL6
0000
C2RXOVF1
0528 RXOVF15 RXOVF14 RXOVF13 RXOVF12 RXOVF11 RXOVF10 RXOVF09 RXOVF08 RXOVF7
RXOVF0
0000
C2RXOVF2
052A RXOVF31 RXOVF30 RXOVF29 RXOVF28 RXOVF27 RXOVF26 RXOVF25 RXOVF24 RXOVF23 RXOVF22 RXOVF21 RXOVF20 RXOVF19 RXOVF18 RXOVF17 RXOVF16
0000
RXOVF6
RXOVF5
RXOVF4
RXOVF3
RXOVF2
RXOVF1
DS70592B-page 49
C2TR01CON 0530
TXEN1
TX
ABAT1
TX
LARB1
TX
ERR1
TX
REQ1
RTREN1
TX1PRI<1:0>
TXEN0
TX
ABAT0
TX
LARB0
TX
ERR0
TX
REQ0
RTREN0
TX0PRI<1:0>
0000
C2TR23CON 0532
TXEN3
TX
ABAT3
TX
LARB3
TX
ERR3
TX
REQ3
RTREN3
TX3PRI<1:0>
TXEN2
TX
ABAT2
TX
LARB2
TX
ERR2
TX
REQ2
RTREN2
TX2PRI<1:0>
0000
C2TR45CON 0534
TXEN5
TX
ABAT5
TX
LARB5
TX
ERR5
TX
REQ5
RTREN5
TX5PRI<1:0>
TXEN4
TX
ABAT4
TX
LARB4
TX
ERR4
TX
REQ4
RTREN4
TX4PRI<1:0>
0000
C2TR67CON 0536
TXEN7
TX
ABAT7
TX
LARB7
TX
ERR7
TX
REQ7
RTREN7
TX7PRI<1:0>
TXEN6
TX
ABAT6
TX
LARB6
TX
ERR6
TX
REQ6
RTREN6
TX6PRI<1:0>
xxxx
C2RXD
0540
Recieved Data Word
xxxx
C2TXD
0542
Transmit Data Word
xxxx
Legend:
x = unknown value on Reset, — = unimplemented, read as ‘0’. Reset values are shown in hexadecimal for PinHigh devices.
PIC24HJXXXGPX06A/X08A/X10A
Addr
File Name
ECAN2 REGISTER MAP WHEN C2CTRL1.WIN = 1 FOR PIC24HJ256GP610A DEVICES ONLY
Addr
Bit 15
Bit 14
Bit 13
Bit 12
Bit 11
Bit 10
Bit 9
0500051E
Bit 8
Bit 7
Bit 6
Bit 5
Bit 4
Bit 3
Bit 2
Bit 1
Bit 0
All
Resets
See definition when WIN = x
Preliminary
 2009 Microchip Technology Inc.
C2BUFPNT1
0520
F3BP<3:0>
F2BP<3:0>
F1BP<3:0>
F0BP<3:0>
0000
C2BUFPNT2
0522
F7BP<3:0>
F6BP<3:0>
F5BP<3:0>
F4BP<3:0>
0000
C2BUFPNT3
0524
F12BP<3:0>
F10BP<3:0>
F9BP<3:0>
F8BP<3:0>
0000
C2BUFPNT4
0526
F15BP<3:0>
F14BP<3:0>
F13BP<3:0>
F12BP<3:0>
0000
C2RXM0SID
0530
SID<10:3>
—
EID<17:16>
xxxx
C2RXM0EID
0532
EID<15:8>
C2RXM1SID
0534
SID<10:3>
—
EID<17:16>
C2RXM1EID
0536
EID<15:8>
C2RXM2SID
0538
SID<10:3>
—
EID<17:16>
C2RXM2EID
053A
EID<15:8>
C2RXF0SID
0540
SID<10:3>
—
EID<17:16>
C2RXF0EID
0542
EID<15:8>
C2RXF1SID
0544
SID<10:3>
—
EID<17:16>
C2RXF1EID
0546
EID<15:8>
C2RXF2SID
0548
SID<10:3>
—
EID<17:16>
C2RXF2EID
054A
EID<15:8>
C2RXF3SID
054C
SID<10:3>
—
EID<17:16>
C2RXF3EID
054E
EID<15:8>
C2RXF4SID
0550
SID<10:3>
—
EID<17:16>
C2RXF4EID
0552
EID<15:8>
C2RXF5SID
0554
SID<10:3>
—
EID<17:16>
C2RXF5EID
0556
EID<15:8>
C2RXF6SID
0558
SID<10:3>
—
EID<17:16>
C2RXF6EID
055A
EID<15:8>
C2RXF7SID
055C
SID<10:3>
—
EID<17:16>
C2RXF7EID
055E
EID<15:8>
C2RXF8SID
0560
SID<10:3>
—
EID<17:16>
C2RXF8EID
0562
EID<15:8>
C2RXF9SID
0564
SID<10:3>
—
EID<17:16>
C2RXF9EID
0566
EID<15:8>
C2RXF10SID
0568
SID<10:3>
—
EID<17:16>
C2RXF10EID
056A
EID<15:8>
C2RXF11SID
056C
SID<10:3>
—
EID<17:16>
Legend:
SID<2:0>
—
MIDE
EID<7:0>
SID<2:0>
—
MIDE
xxxx
EID<7:0>
SID<2:0>
—
MIDE
xxxx
EID<7:0>
SID<2:0>
—
EXIDE
—
EXIDE
—
EXIDE
—
EXIDE
—
EXIDE
—
EXIDE
—
EXIDE
—
EXIDE
—
EXIDE
—
EXIDE
—
EXIDE
x = unknown value on Reset, — = unimplemented, read as ‘0’. Reset values are shown in hexadecimal for PinHigh devices.
—
EXIDE
xxxx
xxxx
EID<7:0>
SID<2:0>
xxxx
xxxx
EID<7:0>
SID<2:0>
xxxx
xxxx
EID<7:0>
SID<2:0>
xxxx
xxxx
EID<7:0>
SID<2:0>
xxxx
xxxx
EID<7:0>
SID<2:0>
xxxx
xxxx
EID<7:0>
SID<2:0>
xxxx
xxxx
EID<7:0>
SID<2:0>
xxxx
xxxx
EID<7:0>
SID<2:0>
xxxx
xxxx
EID<7:0>
SID<2:0>
xxxx
xxxx
EID<7:0>
SID<2:0>
xxxx
xxxx
EID<7:0>
SID<2:0>
xxxx
xxxx
xxxx
xxxx
PIC24HJXXXGPX06A/X08A/X10A
DS70592B-page 50
TABLE 4-23:
 2009 Microchip Technology Inc.
TABLE 4-23:
ECAN2 REGISTER MAP WHEN C2CTRL1.WIN = 1 FOR PIC24HJ256GP610A DEVICES ONLY (CONTINUED)
Addr
C2RXF11EID
056E
EID<15:8>
C2RXF12SID
0570
SID<10:3>
C2RXF12EID
0572
EID<15:8>
C2RXF13SID
0574
SID<10:3>
C2RXF13EID
0576
EID<15:8>
C2RXF14SID
0578
SID<10:3>
C2RXF14EID
057A
EID<15:8>
C2RXF15SID
057C
SID<10:3>
C2RXF15EID
057E
EID<15:8>
Legend:
Bit 15
Bit 14
Bit 13
Bit 12
Bit 11
Bit 10
Bit 9
Bit 8
Bit 7
Bit 6
Bit 5
Bit 4
Bit 3
Bit 2
Bit 1
Bit 0
EID<7:0>
SID<2:0>
—
EXIDE
xxxx
—
EID<17:16>
—
EID<17:16>
—
EID<17:16>
—
EID<17:16>
EID<7:0>
SID<2:0>
—
EXIDE
—
EXIDE
x = unknown value on Reset, — = unimplemented, read as ‘0’. Reset values are shown in hexadecimal for PinHigh devices.
—
EXIDE
EID<7:0>
xxxx
xxxx
EID<7:0>
SID<2:0>
xxxx
xxxx
EID<7:0>
SID<2:0>
All
Resets
xxxx
xxxx
xxxx
xxxx
Preliminary
DS70592B-page 51
PIC24HJXXXGPX06A/X08A/X10A
File Name
File Name
PORTA REGISTER MAP(1)
Bit 8
Bit 7
Bit 6
Bit 5
Bit 4
Bit 3
Bit 2
Bit 1
Bit 0
All
Resets
TRISA9
—
TRISA7
TRISA6
TRISA5
TRISA4
TRISA3
TRISA2
TRISA1
TRISA0
F6FF
RA9
—
RA7
RA6
RA5
RA4
RA3
RA2
RA1
RA0
xxxx
LATA10
LATA9
—
LATA7
LATA6
LATA5
LATA4
LATA3
LATA2
LATA1
LATA0
xxxx
—
—
—
—
—
ODCA5
ODCA4
ODCA3
ODCA2
ODCA1
ODCA0
0000
Addr
Bit 15
Bit 14
Bit 13
Bit 12
Bit 11
Bit 10
Bit 9
TRISA
02C0
TRISA15
TRISA14
TRISA13
TRISA12
—
TRISA10
PORTA
02C2
RA15
RA14
RA13
RA12
—
RA10
LATA
02C4
LATA15
LATA14
LATA13
LATA12
—
ODCA
06C0
ODCA15
ODCA14
—
—
—
Legend:
Note 1:
x = unknown value on Reset, — = unimplemented, read as ‘0’. Reset values are shown in hexadecimal for PinHigh devices.
The actual set of I/O port pins varies from one device to another. Please refer to the corresponding pinout diagrams.
TABLE 4-25:
PORTB REGISTER MAP(1)
Addr
Bit 15
Bit 14
Bit 13
Bit 12
Bit 11
Bit 10
Bit 9
Bit 8
Bit 7
Bit 6
Bit 5
Bit 4
Bit 3
Bit 2
Bit 1
Bit 0
All
Resets
TRISB
02C6
TRISB15
TRISB14
TRISB13
TRISB12
TRISB11
TRISB10
TRISB9
TRISB8
TRISB7
TRISB6
TRISB5
TRISB4
TRISB3
TRISB2
TRISB1
TRISB0
FFFF
PORTB
02C8
RB15
RB14
RB13
RB12
RB11
RB10
RB9
RB8
RB7
RB6
RB5
RB4
RB3
RB2
RB1
RB0
xxxx
LATB
02CA
LATB15
LATB14
LATB13
LATB12
LATB11
LATB10
LATB9
LATB8
LATB7
LATB6
LATB5
LATB4
LATB3
LATB2
LATB1
LATB0
xxxx
Legend:
Note 1:
x = unknown value on Reset, — = unimplemented, read as ‘0’. Reset values are shown in hexadecimal for PinHigh devices.
The actual set of I/O port pins varies from one device to another. Please refer to the corresponding pinout diagrams.
File Name
Preliminary
TABLE 4-26:
PORTC REGISTER MAP(1)
Bit 14
Bit 13
Bit 12
Bit 10
Bit 9
Bit 8
Bit 7
Bit 6
Bit 5
Bit 4
Bit 3
Bit 2
Bit 1
Bit 0
All
Resets
—
—
—
—
—
—
—
TRISC4
TRISC3
TRISC2
TRISC1
—
F01E
—
—
—
—
—
—
—
RC4
RC3
RC2
RC1
—
xxxx
—
—
—
—
—
—
—
LATC4
LATC3
LATC2
LATC1
—
xxxx
Addr
TRISC
02CC
PORTC
02CE
RC15
RC14
RC13
RC12
LATC
02D0
LATC15
LATC14
LATC13
LATC12
Legend:
Note 1:
x = unknown value on Reset, — = unimplemented, read as ‘0’. Reset values are shown in hexadecimal for PinHigh devices.
The actual set of I/O port pins varies from one device to another. Please refer to the corresponding pinout diagrams.
 2009 Microchip Technology Inc.
TABLE 4-27:
Bit 15
Bit 11
File Name
TRISC15 TRISC14 TRISC13 TRISC12
PORTD REGISTER MAP(1)
File Name
Addr
Bit 15
Bit 14
Bit 13
Bit 12
Bit 11
Bit 10
Bit 9
Bit 8
Bit 7
Bit 6
Bit 5
Bit 4
Bit 3
Bit 2
Bit 1
Bit 0
All
Resets
TRISD
02D2
TRISD15
TRISD14
TRISD13
TRISD12
TRISD11
TRISD10
TRISD9
TRISD8
TRISD7
TRISD6
TRISD5
TRISD4
TRISD3
TRISD2
TRISD1
TRISD0
FFFF
PORTD
02D4
RD15
RD14
RD13
RD12
RD11
RD10
RD9
RD8
RD7
RD6
RD5
RD4
RD3
RD2
RD1
RD0
xxxx
LATD
02D6
LATD15
LATD14
LATD13
LATD12
LATD11
LATD10
LATD9
LATD8
LATD7
LATD6
LATD5
LATD4
LATD3
LATD2
LATD1
LATD0
xxxx
ODCD
06D2
ODCD15
ODCD14
ODCD13
ODCD12
ODCD11
ODCD10
ODCD9
ODCD8
ODCD7
ODCD6
ODCD5
ODCD4
ODCD3
ODCD2
ODCD1
ODCD0
0000
Legend:
Note 1:
x = unknown value on Reset, — = unimplemented, read as ‘0’. Reset values are shown in hexadecimal for PinHigh devices.
The actual set of I/O port pins varies from one device to another. Please refer to the corresponding pinout diagrams.
PIC24HJXXXGPX06A/X08A/X10A
DS70592B-page 52
TABLE 4-24:
 2009 Microchip Technology Inc.
TABLE 4-28:
PORTE REGISTER MAP(1)
Addr
Bit 15
Bit 14
Bit 13
Bit 12
Bit 11
Bit 10
Bit 9
Bit 8
Bit 7
Bit 6
Bit 5
Bit 4
Bit 3
Bit 2
Bit 1
Bit 0
All
Resets
TRISE
02D8
—
—
—
—
—
—
—
—
TRISE7
TRISE6
TRISE5
TRISE4
TRISE3
TRISE2
TRISE1
TRISE0
00FF
PORTE
02DA
—
—
—
—
—
—
—
—
RE7
RE6
RE5
RE4
RE3
RE2
RE1
RE0
xxxx
LATE
02DC
—
—
—
—
—
—
—
—
LATE7
LATE6
LATE5
LATE4
LATE3
LATE2
LATE1
LATE0
xxxx
Legend:
Note 1:
x = unknown value on Reset, — = unimplemented, read as ‘0’. Reset values are shown in hexadecimal for PinHigh devices.
The actual set of I/O port pins varies from one device to another. Please refer to the corresponding pinout diagrams.
File Name
TABLE 4-29:
PORTF REGISTER MAP(1)
Addr
Bit 15
Bit 14
Bit 13
Bit 12
Bit 11
Bit 10
Bit 9
Bit 8
Bit 7
Bit 6
Bit 5
Bit 4
Bit 3
Bit 2
Bit 1
Bit 0
All Resets
TRISF
02DE
—
—
TRISF13
TRISF12
—
—
—
TRISF8
TRISF7
TRISF6
TRISF5
TRISF4
TRISF3
TRISF2
TRISF1
TRISF0
31FF
PORTF
02E0
—
—
RF13
RF12
—
—
—
RF8
RF7
RF6
RF5
RF4
RF3
RF2
RF1
RF0
xxxx
LATF
02E2
—
—
LATF13
LATF12
—
—
—
LATF8
LATF7
LATF6
LATF5
LATF4
LATF3
LATF2
LATF1
LATF0
xxxx
ODCF(2)
06DE
—
—
ODCF13
ODCF12
—
—
—
ODCF8
ODCF7
ODCF6
ODCF5
ODCF4
ODCF3
ODCF2
ODCF1
ODCF0
0000
Legend:
Note 1:
x = unknown value on Reset, — = unimplemented, read as ‘0’. Reset values are shown in hexadecimal for PinHigh devices.
The actual set of I/O port pins varies from one device to another. Please refer to the corresponding pinout diagrams.
TABLE 4-30:
PORTG REGISTER MAP(1)
Addr
Bit 15
Bit 14
Bit 13
Bit 12
Bit 11
Bit 10
Bit 9
Bit 8
Bit 7
Bit 6
Bit 5
Bit 4
Bit 3
Bit 2
Bit 1
Bit 0
All
Resets
TRISG
02E4
TRISG15
TRISG14
TRISG13
TRISG12
—
—
TRISG9
TRISG8
TRISG7
TRISG6
—
—
TRISG3
TRISG2
TRISG1
TRISG0
F3CF
PORTG
02E6
RG15
RG14
RG13
RG12
—
—
RG9
RG8
RG7
RG6
—
—
RG3
RG2
RG1
RG0
xxxx
LATG
02E8
LATG15
LATG14
LATG13
LATG12
—
—
LATG9
LATG8
LATG7
LATG6
—
—
LATG3
LATG2
LATG1
LATG0
xxxx
ODCG(2)
06E4
ODCG15
ODCG14
ODCG13
ODCG12
—
—
ODCG9
ODCG8
ODCG7
ODCG6
—
—
ODCG3
ODCG2
ODCG1
ODCG0
0000
Legend:
Note 1:
x = unknown value on Reset, — = unimplemented, read as ‘0’. Reset values are shown in hexadecimal for PinHigh devices.
The actual set of I/O port pins varies from one device to another. Please refer to the corresponding pinout diagrams.
File Name
DS70592B-page 53
PIC24HJXXXGPX06A/X08A/X10A
Preliminary
File Name
SYSTEM CONTROL REGISTER MAP
File Name
Addr
Bit 15
Bit 14
Bit 13
Bit 12
Bit 11
Bit 10
Bit 9
Bit 8
Bit 7
Bit 6
Bit 5
Bit 4
Bit 3
Bit 2
Bit 1
Bit 0
All
Resets
RCON
0740
TRAPR
IOPUWR
—
—
—
—
—
VREGS
EXTR
SWR
SWDTEN
WDTO
SLEEP
IDLE
BOR
POR
xxxx(1)
OSCCON
0742
—
CLKLOCK
—
LOCK
—
CF
—
LPOSCEN
OSWEN
0300(2)
COSC<2:0>
—
CLKDIV
0744
ROI
PLLFBD
0746
—
—
—
—
—
—
—
OSCTUN
0748
—
—
—
—
—
—
—
Legend:
Note 1:
2:
x = unknown value on Reset, — = unimplemented, read as ‘0’. Reset values are shown in hexadecimal for PinHigh devices.
RCON register Reset values dependent on type of Reset.
OSCCON register Reset values dependent on the FOSC Configuration bits and by type of Reset.
TABLE 4-32:
File Name
DOZE<2:0>
NOSC<2:0>
DOZEN
FRCDIV<2:0>
Preliminary
Bit 15
Bit 14
Bit 13
NVMCON
0760
WR
WREN
WRERR
—
—
—
NVMKEY
0766
—
—
—
—
—
—
PLLPRE<4:0>
3040
PLLDIV<8:0>
—
—
0030
—
TUN<5:0>
0000
Bit 12
Bit 11
Bit 10
Bit 9
Bit 8
Bit 7
Bit 6
Bit 5
—
—
—
ERASE
—
—
—
Bit 4
Bit 3
—
Bit 2
Bit 1
Bit 0
All
Resets
0000(1)
NVMOP<3:0>
NVMKEY<7:0>
0000
x = unknown value on Reset, — = unimplemented, read as ‘0’. Reset values are shown in hexadecimal for PinHigh devices.
Reset value shown is for POR only. Value on other Reset states is dependent on the state of memory write or erase operations at the time of Reset.
TABLE 4-33:
File Name
—
NVM REGISTER MAP
Addr
Legend:
Note 1:
PLLPOST<1:0>
Addr
PMD REGISTER MAP
Bit 15
Bit 14
Bit 13
Bit 12
Bit 11
Bit 10
Bit 9
Bit 8
Bit 7
Bit 6
Bit 5
Bit 4
Bit 3
Bit 2
Bit 1
Bit 0
All
Resets
PMD1
0770
T5MD
T4MD
T3MD
T2MD
T1MD
—
—
—
I2C1MD
U2MD
U1MD
SPI2MD
SPI1MD
C2MD
C1MD
AD1MD
0000
PMD2
0772
IC8MD
IC7MD
IC6MD
IC5MD
IC4MD
IC3MD
IC2MD
IC1MD
OC8MD
OC7MD
OC6MD
OC5MD
OC4MD
OC3MD
OC2MD
OC1MD
0000
PMD3
0774
T9MD
T8MD
T7MD
T6MD
—
—
—
—
—
—
—
—
—
—
I2C2MD
AD2MD
0000
Legend:
x = unknown value on Reset, — = unimplemented, read as ‘0’. Reset values are shown in hexadecimal for PinHigh devices.
PIC24HJXXXGPX06A/X08A/X10A
DS70592B-page 54
TABLE 4-31:
 2009 Microchip Technology Inc.
PIC24HJXXXGPX06A/X08A/X10A
4.2.6
SOFTWARE STACK
4.2.7
In addition to its use as a working register, the W15
register in the PIC24HJXXXGPX06A/X08A/X10A
devices is also used as a software Stack Pointer. The
Stack Pointer always points to the first available free
word and grows from lower to higher addresses. It predecrements for stack pops and post-increments for
stack pushes, as shown in Figure 4-5. For a PC push
during any CALL instruction, the MSB of the PC is zeroextended before the push, ensuring that the MSB is
always clear.
Note:
A PC push during exception processing
concatenates the SRL register to the MSB
of the PC prior to the push.
The Stack Pointer Limit register (SPLIM) associated
with the Stack Pointer sets an upper address boundary
for the stack. SPLIM is uninitialized at Reset. As is the
case for the Stack Pointer, SPLIM<0> is forced to ‘0’
because all stack operations must be word-aligned.
Whenever an EA is generated using W15 as a source
or destination pointer, the resulting address is
compared with the value in SPLIM. If the contents of
the Stack Pointer (W15) and the SPLIM register are
equal and a push operation is performed, a stack error
trap will not occur. The stack error trap will occur on a
subsequent push operation. Thus, for example, if it is
desirable to cause a stack error trap when the stack
grows beyond address 0x2000 in RAM, initialize the
SPLIM with the value 0x1FFE.
Similarly, a Stack Pointer underflow (stack error) trap is
generated when the Stack Pointer address is found to
be less than 0x0800. This prevents the stack from
interfering with the Special Function Register (SFR)
space.
A write to the SPLIM register should not be immediately
followed by an indirect read operation using W15.
FIGURE 4-5:
Stack Grows Towards
Higher Address
0x0000
CALL STACK FRAME
15
0
PC<15:0>
000000000 PC<22:16>
<Free Word>
W15 (before CALL)
W15 (after CALL)
POP : [--W15]
PUSH : [W15++]
 2009 Microchip Technology Inc.
DATA RAM PROTECTION FEATURE
The PIC24H product family supports Data RAM protection features that enable segments of RAM to be
protected when used in conjunction with Boot and
Secure Code Segment Security. BSRAM (Secure RAM
segment for BS) is accessible only from the Boot Segment Flash code, when enabled. SSRAM (Secure
RAM segment for RAM) is accessible only from the
Secure Segment Flash code, when enabled. See
Table 4-1 for an overview of the BSRAM and SSRAM
SFRs.
4.3
Instruction Addressing Modes
The addressing modes in Table 4-34 form the basis of
the addressing modes optimized to support the specific
features of individual instructions. The addressing
modes provided in the MAC class of instructions are
somewhat different from those in the other instruction
types.
4.3.1
FILE REGISTER INSTRUCTIONS
Most file register instructions use a 13-bit address field
(f) to directly address data present in the first 8192
bytes of data memory (Near Data Space). Most file
register instructions employ a working register, W0,
which is denoted as WREG in these instructions. The
destination is typically either the same file register or
WREG (with the exception of the MUL instruction),
which writes the result to a register or register pair. The
MOV instruction allows additional flexibility and can
access the entire data space.
4.3.2
MCU INSTRUCTIONS
The 3-operand MCU instructions are of the form:
Operand 3 = Operand 1 <function> Operand 2
where Operand 1 is always a working register (i.e., the
addressing mode can only be Register Direct) which is
referred to as Wb. Operand 2 can be a W register,
fetched from data memory, or a 5-bit literal. The result
location can be either a W register or a data memory
location. The following addressing modes are
supported by MCU instructions:
•
•
•
•
•
Register Direct
Register Indirect
Register Indirect Post-Modified
Register Indirect Pre-Modified
5-bit or 10-bit Literal
Note:
Preliminary
Not all instructions support all the
addressing modes given above. Individual
instructions may support different subsets
of these addressing modes.
DS70592B-page 55
PIC24HJXXXGPX06A/X08A/X10A
TABLE 4-34:
FUNDAMENTAL ADDRESSING MODES SUPPORTED
Addressing Mode
Description
File Register Direct
The address of the file register is specified explicitly.
Register Direct
The contents of a register are accessed directly.
Register Indirect
The contents of Wn forms the EA.
Register Indirect Post-Modified
The contents of Wn forms the EA. Wn is post-modified (incremented or
decremented) by a constant value.
Register Indirect Pre-Modified
Wn is pre-modified (incremented or decremented) by a signed constant value
to form the EA.
Register Indirect with Register Offset The sum of Wn and Wb forms the EA.
Register Indirect with Literal Offset
4.3.3
The sum of Wn and a literal forms the EA.
MOVE INSTRUCTIONS
4.4
Move instructions provide a greater degree of addressing flexibility than other instructions. In addition to the
Addressing modes supported by most MCU instructions, move instructions also support Register Indirect
with Register Offset Addressing mode, also referred to
as Register Indexed mode.
Note:
For the MOV instructions, the Addressing
mode specified in the instruction can differ
for the source and destination EA.
However, the 4-bit Wb (Register Offset)
field is shared between both source and
destination (but typically only used by
one).
In summary, the following Addressing modes are
supported by move instructions:
•
•
•
•
•
•
•
•
Register Direct
Register Indirect
Register Indirect Post-modified
Register Indirect Pre-modified
Register Indirect with Register Offset (Indexed)
Register Indirect with Literal Offset
8-bit Literal
16-bit Literal
Note:
4.3.4
Not all instructions support all the
Addressing modes given above. Individual
instructions may support different subsets
of these Addressing modes.
OTHER INSTRUCTIONS
Besides the various addressing modes outlined above,
some instructions use literal constants of various sizes.
For example, BRA (branch) instructions use 16-bit
signed literals to specify the branch destination directly,
whereas the DISI instruction uses a 14-bit unsigned
literal field. In some instructions, the source of an operand or result is implied by the opcode itself. Certain
operations, such as NOP, do not have any operands.
DS70592B-page 56
Interfacing Program and Data
Memory Spaces
The PIC24HJXXXGPX06A/X08A/X10A architecture
uses a 24-bit wide program space and a 16-bit wide
data space. The architecture is also a modified Harvard
scheme, meaning that data can also be present in the
program space. To use this data successfully, it must
be accessed in a way that preserves the alignment of
information in both spaces.
Aside
from
normal
execution,
the
PIC24HJXXXGPX06A/X08A/X10A architecture provides two methods by which program space can be
accessed during operation:
• Using table instructions to access individual bytes
or words anywhere in the program space
• Remapping a portion of the program space into
the data space (Program Space Visibility)
Table instructions allow an application to read or write
to small areas of the program memory. This capability
makes the method ideal for accessing data tables that
need to be updated from time to time. It also allows
access to all bytes of the program word. The remapping method allows an application to access a large
block of data on a read-only basis, which is ideal for
look ups from a large table of static data. It can only
access the least significant word of the program word.
4.4.1
ADDRESSING PROGRAM SPACE
Since the address ranges for the data and program
spaces are 16 and 24 bits, respectively, a method is
needed to create a 23-bit or 24-bit program address
from 16-bit data registers. The solution depends on the
interface method to be used.
For table operations, the 8-bit Table Page register
(TBLPAG) is used to define a 32K word region within
the program space. This is concatenated with a 16-bit
EA to arrive at a full 24-bit program space address. In
this format, the Most Significant bit of TBLPAG is used
to determine if the operation occurs in the user memory
(TBLPAG<7> = 0) or the configuration memory
(TBLPAG<7> = 1).
Preliminary
 2009 Microchip Technology Inc.
PIC24HJXXXGPX06A/X08A/X10A
For remapping operations, the 8-bit Program Space
Visibility register (PSVPAG) is used to define a
16K word page in the program space. When the Most
Significant bit of the EA is ‘1’, PSVPAG is concatenated
with the lower 15 bits of the EA to form a 23-bit program
space address. Unlike table operations, this limits
remapping operations strictly to the user memory area.
TABLE 4-35:
Table 4-35 and Figure 4-6 show how the program EA is
created for table operations and remapping accesses
from the data EA. Here, P<23:0> refers to a program
space word, whereas D<15:0> refers to a data space
word.
PROGRAM SPACE ADDRESS CONSTRUCTION
Access
Space
Access Type
Program Space Address
<23>
<22:16>
<15>
<14:1>
Instruction Access
(Code Execution)
User
TBLRD/TBLWT
(Byte/Word Read/Write)
User
TBLPAG<7:0>
Configuration
TBLPAG<7:0>
Data EA<15:0>
1xxx xxxx
xxxx xxxx xxxx xxxx
Program Space Visibility
(Block Remap/Read)
Note 1:
PC<22:1>
0
0xxx
xxxx
0xxx xxxx
User
xxxx
<0>
0
xxxx
xxxx xxx0
Data EA<15:0>
xxxx xxxx xxxx xxxx
0
PSVPAG<7:0>
0
xxxx xxxx
Data EA<14:0>(1)
xxx xxxx xxxx xxxx
Data EA<15> is always ‘1’ in this case, but is not used in calculating the program space address. Bit 15 of
the address is PSVPAG<0>.
 2009 Microchip Technology Inc.
Preliminary
DS70592B-page 57
PIC24HJXXXGPX06A/X08A/X10A
FIGURE 4-6:
DATA ACCESS FROM PROGRAM SPACE ADDRESS GENERATION
Program Counter(1)
Program Counter
0
0
23 bits
EA
Table Operations(2)
1/0
1/0
TBLPAG
8 bits
16 bits
24 bits
Select
Program Space Visibility(1)
(Remapping)
EA
1
0
PSVPAG
0
8 bits
15 bits
23 bits
User/Configuration
Space Select
Byte Select
Note 1: The LSb of program space addresses is always fixed as ‘0’ in order to maintain word
alignment of data in the program and data spaces.
2: Table operations are not required to be word-aligned. Table read operations are permitted
in the configuration memory space.
DS70592B-page 58
Preliminary
 2009 Microchip Technology Inc.
PIC24HJXXXGPX06A/X08A/X10A
4.4.2
DATA ACCESS FROM PROGRAM
MEMORY USING TABLE
INSTRUCTIONS
2.
TBLRDH (Table Read High): In Word mode, it
maps the entire upper word of a program address
(P<23:16>) to a data address. Note that
D<15:8>, the ‘phantom byte’, will always be ‘0’.
The TBLRDL and TBLWTL instructions offer a direct
method of reading or writing the lower word of any
address within the program space without going
through data space. The TBLRDH and TBLWTH instructions are the only method to read or write the upper
8 bits of a program space word as data.
The PC is incremented by two for each successive
24-bit program word. This allows program memory
addresses to directly map to data space addresses.
Program memory can thus be regarded as two 16-bit,
word wide address spaces, residing side by side, each
with the same address range. TBLRDL and TBLWTL
access the space which contains the least significant
data word and TBLRDH and TBLWTH access the space
which contains the upper data byte.
Two table instructions are provided to move byte or
word sized (16-bit) data to and from program space.
Both function as either byte or word operations.
1.
TBLRDL (Table Read Low): In Word mode, it
maps the lower word of the program space
location (P<15:0>) to a data address (D<15:0>).
In Byte mode, it maps the upper or lower byte of
the program word to D<7:0> of the data
address, as above. Note that the data will
always be ‘0’ when the upper ‘phantom’ byte is
selected (Byte Select = 1).
In a similar fashion, two table instructions, TBLWTH
and TBLWTL, are used to write individual bytes or
words to a program space address. The details of
their operation are explained in Section 5.0 “Flash
Program Memory”.
For all table operations, the area of program memory
space to be accessed is determined by the Table Page
register (TBLPAG). TBLPAG covers the entire program
memory space of the device, including user and configuration spaces. When TBLPAG<7> = 0, the table page
is located in the user memory space. When
TBLPAG<7> = 1, the page is located in configuration
space.
In Byte mode, either the upper or lower byte of
the lower program word is mapped to the lower
byte of a data address. The upper byte is
selected when Byte Select is ‘1’; the lower byte
is selected when it is ‘0’.
FIGURE 4-7:
ACCESSING PROGRAM MEMORY WITH TABLE INSTRUCTIONS
Program Space
TBLPAG
02
23
15
0
0x000000
23
16
8
0
00000000
00000000
0x020000
00000000
0x030000
00000000
‘Phantom’ Byte
TBLRDH.B (Wn<0> = 0)
TBLRDL.B (Wn<0> = 1)
TBLRDL.B (Wn<0> = 0)
TBLRDL.W
0x800000
 2009 Microchip Technology Inc.
The address for the table operation is determined by the data EA
within the page defined by the TBLPAG register.
Only read operations are shown; write operations are also valid in
the user memory area.
Preliminary
DS70592B-page 59
PIC24HJXXXGPX06A/X08A/X10A
4.4.3
READING DATA FROM PROGRAM
MEMORY USING PROGRAM SPACE
VISIBILITY
The upper 32 Kbytes of data space may optionally be
mapped into any 16K word page of the program space.
This option provides transparent access of stored constant data from the data space without the need to use
special instructions (i.e., TBLRDL/H).
Program space access through the data space occurs
if the Most Significant bit of the data space EA is ‘1’ and
program space visibility is enabled by setting the PSV
bit in the Core Control register (CORCON<2>). The
location of the program memory space to be mapped
into the data space is determined by the Program
Space Visibility Page register (PSVPAG). This 8-bit
register defines any one of 256 possible pages of
16K words in program space. In effect, PSVPAG functions as the upper 8 bits of the program memory
address, with the 15 bits of the EA functioning as the
lower bits. Note that by incrementing the PC by 2 for
each program memory word, the lower 15 bits of data
space addresses directly map to the lower 15 bits in the
corresponding program space addresses.
Data reads to this area add an additional cycle to the
instruction being executed, since two program memory
fetches are required.
Although each data space address, 8000h and higher,
maps directly into a corresponding program memory
address (see Figure 4-8), only the lower 16 bits of the
FIGURE 4-8:
24-bit program word are used to contain the data. The
upper 8 bits of any program space location used as
data should be programmed with ‘1111 1111’ or
‘0000 0000’ to force a NOP. This prevents possible
issues should the area of code ever be accidentally
executed.
Note:
PSV access is temporarily disabled during
table reads/writes.
For operations that use PSV and are executed outside
a REPEAT loop, the MOV and MOV.D instructions
require one instruction cycle in addition to the specified
execution time. All other instructions require two
instruction cycles in addition to the specified execution
time.
For operations that use PSV, which are executed inside
a REPEAT loop, there will be some instances that
require two instruction cycles in addition to the
specified execution time of the instruction:
• Execution in the first iteration
• Execution in the last iteration
• Execution prior to exiting the loop due to an
interrupt
• Execution upon re-entering the loop after an
interrupt is serviced
Any other iteration of the REPEAT loop will allow the
instruction accessing data, using PSV, to execute in a
single cycle.
PROGRAM SPACE VISIBILITY OPERATION
When CORCON<2> = 1 and EA<15> = 1:
Program Space
PSVPAG
02
23
15
Data Space
0
0x000000
0x0000
Data EA<14:0>
0x010000
0x018000
The data in the page
designated by PSVPAG is mapped into
the upper half of the
data memory
space...
0x8000
PSV Area
0x800000
DS70592B-page 60
Preliminary
...while the lower 15 bits
of the EA specify an
exact address within
0xFFFF the PSV area. This
corresponds exactly to
the same lower 15 bits
of the actual program
space address.
 2009 Microchip Technology Inc.
PIC24HJXXXGPX06A/X08A/X10A
5.0
FLASH PROGRAM MEMORY
lines for power (VDD), ground (VSS) and Master Clear
(MCLR). This allows customers to manufacture boards
with unprogrammed devices and then program the digital signal controller just before shipping the product.
This also allows the most recent firmware or a custom
firmware to be programmed.
Note 1: This data sheet summarizes the features
of the PIC24HJXXXGPX06A/X08A/X10A
family of devices. However, it is not
intended to be a comprehensive reference source. To complement the information in this data sheet, refer to Section 5.
“Flash Programming” (DS70228) of the
“dsPIC33F/PIC24H Family Reference
Manual”, which is available from the
Microchip website (www.microchip.com).
RTSP is accomplished using TBLRD (table read) and
TBLWT (table write) instructions. With RTSP, the user
can write program memory data either in blocks or
‘rows’ of 64 instructions (192 bytes) at a time, or single
instructions and erase program memory in blocks or
‘pages’ of 512 instructions (1536 bytes) at a time.
2: Some registers and associated bits
described in this section may not be available on all devices. Refer to Section 4.0
“Memory Organization” in this data
sheet for device-specific register and bit
information.
5.1
The PIC24HJXXXGPX06A/X08A/X10A devices contain internal Flash program memory for storing and
executing application code. The memory is readable,
writable and erasable during normal operation over the
entire VDD range.
Flash memory can be programmed in two ways:
1.
2.
In-Circuit Serial Programming™ (ICSP™)
programming capability
Run-Time Self-Programming (RTSP)
ICSP
programming
capability
allows
a
PIC24HJXXXGPX06A/X08A/X10A device to be serially programmed while in the end application circuit.
This is simply done with two lines for programming
clock and programming data (one of the alternate programming pin pairs: PGECx/PGEDx, and three other
FIGURE 5-1:
Table Instructions and Flash
Programming
Regardless of the method used, all programming of
Flash memory is done with the table read and table
write instructions. These allow direct read and write
access to the program memory space from the data
memory while the device is in normal operating mode.
The 24-bit target address in the program memory is
formed using bits<7:0> of the TBLPAG register and the
Effective Address (EA) from a W register specified in
the table instruction, as shown in Figure 5-1.
The TBLRDL and the TBLWTL instructions are used to
read or write to bits<15:0> of program memory.
TBLRDL and TBLWTL can access program memory in
both Word and Byte modes.
The TBLRDH and TBLWTH instructions are used to read
or write to bits<23:16> of program memory. TBLRDH
and TBLWTH can also access program memory in Word
or Byte mode.
ADDRESSING FOR TABLE REGISTERS
24 bits
Using
Program Counter
Program Counter
0
0
Working Reg EA
Using
Table Instruction
1/0
TBLPAG Reg
8 bits
User/Configuration
Space Select
 2009 Microchip Technology Inc.
16 bits
24-bit EA
Preliminary
Byte
Select
DS70592B-page 61
PIC24HJXXXGPX06A/X08A/X10A
5.2
RTSP Operation
5.3
The PIC24HJXXXGPX06A/X08A/X10A Flash program
memory array is organized into rows of 64 instructions
or 192 bytes. RTSP allows the user to erase a page of
memory, which consists of eight rows (512 instructions)
at a time, and to program one row or one word at a
time. Table 24-12 displays typical erase and programming times. The 8-row erase pages and single row
write rows are edge-aligned, from the beginning of program memory, on boundaries of 1536 bytes and 192
bytes, respectively.
The program memory implements holding buffers that
can contain 64 instructions of programming data. Prior
to the actual programming operation, the write data
must be loaded into the buffers in sequential order. The
instruction words loaded must always be from a group
of 64 boundary.
The basic sequence for RTSP programming is to set up
a Table Pointer, then do a series of TBLWT instructions
to load the buffers. Programming is performed by setting the control bits in the NVMCON register. A total of
64 TBLWTL and TBLWTH instructions are required to
load the instructions.
All of the table write operations are single-word writes
(two instruction cycles) because only the buffers are
written. A programming cycle is required for
programming each row.
Programming Operations
A complete programming sequence is necessary for
programming or erasing the internal Flash in RTSP
mode. The processor stalls (waits) until the
programming operation is finished.
The programming time depends on the FRC accuracy
(see Table 24-19) and the value of the FRC Oscillator
Tuning register (see Register 9-4). Use the following
formula to calculate the minimum and maximum values
for the Row Write Time, Page Erase Time and Word
Write Cycle Time parameters (see Table 24-12).
EQUATION 5-1:
PROGRAMMING TIME
T
-------------------------------------------------------------------------------------------------------------------------7.37 MHz   FRC Accuracy %   FRC Tuning %
For example, if the device is operating at +125°C,
the FRC accuracy will be ±5%. If the TUN<5:0> bits
(see Register 9-4) are set to ‘b111111, the
Minimum Row Write Time is:
11064 Cycles
T RW = ---------------------------------------------------------------------------------------------- = 1.435ms
7.37 MHz   1 + 0.05    1 – 0.00375 
and, the Maximum Row Write Time is:
11064 Cycles
T RW = ---------------------------------------------------------------------------------------------- = 1.586ms
7.37 MHz   1 – 0.05    1 – 0.00375 
Setting the WR bit (NVMCON<15>) starts the operation, and the WR bit is automatically cleared when the
operation is finished.
5.4
Control Registers
There are two SFRs used to read and write the
program Flash memory: NVMCON and NVMKEY.
The NVMCON register (Register 5-1) controls which
blocks are to be erased, which memory type is to be
programmed and the start of the programming cycle.
NVMKEY is a write-only register that is used for write
protection. To start a programming or erase sequence,
the user must consecutively write 0x55 and 0xAA to the
NVMKEY register. Refer to Section 5.3 “Programming
Operations” for further details.
DS70592B-page 62
Preliminary
 2009 Microchip Technology Inc.
PIC24HJXXXGPX06A/X08A/X10A
REGISTER 5-1:
NVMCON: FLASH MEMORY CONTROL REGISTER
R/SO-0(1)
R/W-0(1)
R/W-0(1)
U-0
U-0
U-0
U-0
U-0
WR
WREN
WRERR
—
—
—
—
—
bit 15
bit 8
R/W-0(1)
U-0
—
ERASE
U-0
—
R/W-0(1)
U-0
R/W-0(1)
R/W-0(1)
R/W-0(1)
NVMOP<3:0>(2)
—
bit 7
bit 0
Legend:
SO = Settable only bit
R = Readable bit
W = Writable bit
U = Unimplemented bit, read as ‘0’
-n = Value at POR
‘1’ = Bit is set
‘0’ = Bit is cleared
x = Bit is unknown
bit 15
WR: Write Control bit
1 = Initiates a Flash memory program or erase operation. The operation is self-timed and the bit is
cleared by hardware once operation is complete
0 = Program or erase operation is complete and inactive
bit 14
WREN: Write Enable bit
1 = Enable Flash program/erase operations
0 = Inhibit Flash program/erase operations
bit 13
WRERR: Write Sequence Error Flag bit
1 = An improper program or erase sequence attempt or termination has occurred (bit is set
automatically on any set attempt of the WR bit)
0 = The program or erase operation completed normally
bit 12-7
Unimplemented: Read as ‘0’
bit 6
ERASE: Erase/Program Enable bit
1 = Perform the erase operation specified by NVMOP<3:0> on the next WR command
0 = Perform the program operation specified by NVMOP<3:0> on the next WR command
bit 5-4
Unimplemented: Read as ‘0’
bit 3-0
NVMOP<3:0>: NVM Operation Select bits(2)
1111 = Memory bulk erase operation (ERASE = 1) or no operation (ERASE = 0)
1110 = Reserved
1101 = Erase General Segment and FGS Configuration Register
(ERASE = 1) or no operation (ERASE = 0)
1100 = Erase Secure Segment and FSS Configuration Register
(ERASE = 1) or no operation (ERASE = 0)
1011-0100 = Reserved
0011 = Memory word program operation (ERASE = 0) or no operation (ERASE = 1)
0010 = Memory page erase operation (ERASE = 1) or no operation (ERASE = 0)
0001 = Memory row program operation (ERASE = 0) or no operation (ERASE = 1)
0000 = Program or erase a single Configuration register byte
Note 1: These bits can only be reset on POR.
2: All other combinations of NVMOP<3:0> are unimplemented.
 2009 Microchip Technology Inc.
Preliminary
DS70592B-page 63
PIC24HJXXXGPX06A/X08A/X10A
5.4.1
PROGRAMMING ALGORITHM FOR
FLASH PROGRAM MEMORY
4.
5.
The user can program one row of program Flash
memory at a time. To do this, it is necessary to erase
the 8-row erase page that contains the desired row.
The general process is:
1.
2.
3.
Read eight rows of program memory
(512 instructions) and store in data RAM.
Update the program data in RAM with the
desired new data.
Erase the page (see Example 5-1):
a) Set the NVMOP bits (NVMCON<3:0>) to
‘0010’ to configure for block erase. Set the
ERASE (NVMCON<6>) and WREN
(NVMCON<14>) bits.
b) Write the starting address of the page to be
erased into the TBLPAG and W registers.
c) Perform a dummy table write operation
(TBLWTL) to any address within the page
that needs to be erased.
d) Write 0x55 to NVMKEY.
e) Write 0xAA to NVMKEY.
f) Set the WR bit (NVMCON<15>). The erase
cycle begins and the CPU stalls for the duration of the erase cycle. When the erase is
done, the WR bit is cleared automatically.
EXAMPLE 5-1:
Note:
For protection against accidental operations, the write
initiate sequence for NVMKEY must be used to allow
any erase or program operation to proceed. After the
programming command has been executed, the user
must wait for the programming time until programming
is complete. The two instructions following the start of
the programming sequence should be NOPs, as shown
in Example 5-3.
ERASING A PROGRAM MEMORY PAGE
; Set up NVMCON for block erase operation
MOV
#0x4042, W0
MOV
W0, NVMCON
; Init pointer to row to be ERASED
MOV
#tblpage(PROG_ADDR), W0
MOV
W0, TBLPAG
MOV
#tbloffset(PROG_ADDR), W0
TBLWTL W0, [W0]
DISI
#5
MOV
MOV
MOV
MOV
BSET
NOP
NOP
6.
Write the first 64 instructions from data RAM into
the program memory buffers (see Example 5-2).
Write the program block to Flash memory:
a) Set the NVMOP bits to ‘0001’ to configure
for row programming. Clear the ERASE bit
and set the WREN bit.
b) Write 0x55 to NVMKEY.
c) Write 0xAA to NVMKEY.
d) Set the WR bit. The programming cycle
begins and the CPU stalls for the duration of
the write cycle. When the write to Flash memory is done, the WR bit is cleared
automatically.
Repeat steps 4 and 5, using the next available
64 instructions from the block in data RAM by
incrementing the value in TBLPAG, until all
512 instructions are written back to Flash memory.
#0x55, W0
W0, NVMKEY
#0xAA, W1
W1, NVMKEY
NVMCON, #WR
;
; Initialize NVMCON
;
;
;
;
;
;
;
;
;
;
;
;
Initialize PM Page Boundary SFR
Initialize in-page EA<15:0> pointer
Set base address of erase block
Block all interrupts with priority <7
for next 5 instructions
Write the 55 key
Write the AA key
Start the erase sequence
Insert two NOPs after the erase
command is asserted
A program memory page erase operation
is set up by performing a dummy table
write (TBLWTL) operation to any address
within the page. This methodology is different from the page erase operation on
dsPIC30F/33F devices in which the erase
page was selected using a dedicated pair
of registers (NVMADRU and NVMADR).
DS70592B-page 64
Preliminary
 2009 Microchip Technology Inc.
PIC24HJXXXGPX06A/X08A/X10A
EXAMPLE 5-2:
LOADING THE WRITE BUFFERS
; Set up NVMCON for row programming operations
MOV
#0x4001, W0
;
MOV
W0, NVMCON
; Initialize NVMCON
; Set up a pointer to the first program memory location to be written
; program memory selected, and writes enabled
MOV
#0x0000, W0
;
MOV
W0, TBLPAG
; Initialize PM Page Boundary SFR
MOV
#0x6000, W0
; An example program memory address
; Perform the TBLWT instructions to write the latches
; 0th_program_word
MOV
#LOW_WORD_0, W2
;
MOV
#HIGH_BYTE_0, W3
;
TBLWTL W2, [W0]
; Write PM low word into program latch
TBLWTH W3, [W0++]
; Write PM high byte into program latch
; 1st_program_word
MOV
#LOW_WORD_1, W2
;
MOV
#HIGH_BYTE_1, W3
;
TBLWTL W2, [W0]
; Write PM low word into program latch
TBLWTH W3, [W0++]
; Write PM high byte into program latch
; 2nd_program_word
MOV
#LOW_WORD_2, W2
;
MOV
#HIGH_BYTE_2, W3
;
; Write PM low word into program latch
TBLWTL W2, [W0]
; Write PM high byte into program latch
TBLWTH W3, [W0++]
•
•
•
; 63rd_program_word
MOV
#LOW_WORD_31, W2
;
MOV
#HIGH_BYTE_31, W3
;
; Write PM low word into program latch
TBLWTL W2, [W0]
; Write PM high byte into program latch
TBLWTH W3, [W0++]
EXAMPLE 5-3:
INITIATING A PROGRAMMING SEQUENCE
DISI
#5
MOV
MOV
MOV
MOV
BSET
NOP
NOP
#0x55, W0
W0, NVMKEY
#0xAA, W1
W1, NVMKEY
NVMCON, #WR
 2009 Microchip Technology Inc.
; Block all interrupts with priority <7
; for next 5 instructions
;
;
;
;
;
;
Write the 55 key
Write the AA key
Start the erase sequence
Insert two NOPs after the
erase command is asserted
Preliminary
DS70592B-page 65
PIC24HJXXXGPX06A/X08A/X10A
NOTES:
DS70592B-page 66
Preliminary
 2009 Microchip Technology Inc.
PIC24HJXXXGPX06A/X08A/X10A
6.0
RESET
A simplified block diagram of the Reset module is
shown in Figure 6-1.
Note 1: This data sheet summarizes the features
of the PIC24HJXXXGPX06A/X08A/X10A
family of devices. However, it is not
intended to be a comprehensive
reference source. To complement the
information in this data sheet, refer to
Section 8. “Reset” (DS70229) of the
“dsPIC33F/PIC24H Family Reference
Manual”, , which is available from the
Microchip website (www.microchip.com).
2: Some registers and associated bits
described in this section may not be available on all devices. Refer to Section 4.0
“Memory Organization” in this data
sheet for device-specific register and bit
information.
The Reset module combines all Reset sources and
controls the device Master Reset Signal, SYSRST. The
following is a list of device Reset sources:
•
•
•
•
•
•
•
POR: Power-on Reset
BOR: Brown-out Reset
MCLR: Master Clear Pin Reset
SWR: RESET Instruction
WDT: Watchdog Timer Reset
TRAPR: Trap Conflict Reset
IOPUWR: Illegal Opcode and Uninitialized W
Register Reset
FIGURE 6-1:
Any active source of Reset will make the SYSRST signal active. Many registers associated with the CPU and
peripherals are forced to a known Reset state. Most
registers are unaffected by a Reset; their status is
unknown on POR and unchanged by all other Resets.
Note:
Refer to the specific peripheral or CPU
section of this manual for register Reset
states.
All types of device Reset will set a corresponding status
bit in the RCON register to indicate the type of Reset
(see Register 6-1). A POR will clear all bits, except for
the POR bit (RCON<0>), that are set. The user can set
or clear any bit at any time during code execution. The
RCON bits only serve as status bits. Setting a particular
Reset status bit in software does not cause a device
Reset to occur.
The RCON register also has other bits associated with
the Watchdog Timer and device power-saving states.
The function of these bits is discussed in other sections
of this manual.
Note:
The status bits in the RCON register
should be cleared after they are read so
that the next RCON register value after a
device Reset will be meaningful.
RESET SYSTEM BLOCK DIAGRAM
RESET Instruction
Glitch Filter
MCLR
WDT
Module
Sleep or Idle
BOR
Internal
Regulator
SYSRST
VDD
VDD Rise
Detect
POR
Trap Conflict
Illegal Opcode
Uninitialized W Register
 2009 Microchip Technology Inc.
Preliminary
DS70592B-page 67
PIC24HJXXXGPX06A/X08A/X10A
RCON: RESET CONTROL REGISTER(1)
REGISTER 6-1:
R/W-0
R/W-0
U-0
U-0
U-0
U-0
U-0
R/W-0
TRAPR
IOPUWR
—
—
—
—
—
VREGS(3)
bit 15
bit 8
R/W-0
EXTR
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
R/W-1
R/W-1
SWR
SWDTEN(2)
WDTO
SLEEP
IDLE
BOR
POR
bit 7
bit 0
Legend:
R = Readable bit
W = Writable bit
U = Unimplemented bit, read as ‘0’
-n = Value at POR
‘1’ = Bit is set
‘0’ = Bit is cleared
x = Bit is unknown
bit 15
TRAPR: Trap Reset Flag bit
1 = A Trap Conflict Reset has occurred
0 = A Trap Conflict Reset has not occurred
bit 14
IOPUWR: Illegal Opcode or Uninitialized W Access Reset Flag bit
1 = An illegal opcode detection, an illegal address mode or uninitialized W register used as an
Address Pointer caused a Reset
0 = An illegal opcode or uninitialized W Reset has not occurred
bit 13-9
Unimplemented: Read as ‘0’
bit 8
VREGS: Voltage Regulator Standby During Sleep bit(3)
1 = Voltage Regulator is active during Sleep mode
0 = Voltage Regulator goes into standby mode during Sleep
bit 7
EXTR: External Reset (MCLR) Pin bit
1 = A Master Clear (pin) Reset has occurred
0 = A Master Clear (pin) Reset has not occurred
bit 6
SWR: Software Reset (Instruction) Flag bit
1 = A RESET instruction has been executed
0 = A RESET instruction has not been executed
bit 5
SWDTEN: Software Enable/Disable of WDT bit(2)
1 = WDT is enabled
0 = WDT is disabled
bit 4
WDTO: Watchdog Timer Time-out Flag bit
1 = WDT time-out has occurred
0 = WDT time-out has not occurred
bit 3
SLEEP: Wake-up from Sleep Flag bit
1 = Device has been in Sleep mode
0 = Device has not been in Sleep mode
bit 2
IDLE: Wake-up from Idle Flag bit
1 = Device was in Idle mode
0 = Device was not in Idle mode
bit 1
BOR: Brown-out Reset Flag bit
1 = A Brown-out Reset has occurred
0 = A Brown-out Reset has not occurred
Note 1: All of the Reset status bits may be set or cleared in software. Setting one of these bits in software does not
cause a device Reset.
2: If the FWDTEN Configuration bit is ‘1’ (unprogrammed), the WDT is always enabled, regardless of the
SWDTEN bit setting.
3: For PIC24HJ256GPX06A/X08A/X10A devices, this bit is unimplemented and reads back programmed
value.
DS70592B-page 68
Preliminary
 2009 Microchip Technology Inc.
PIC24HJXXXGPX06A/X08A/X10A
REGISTER 6-1:
bit 0
RCON: RESET CONTROL REGISTER(1)
POR: Power-on Reset Flag bit
1 = A Power-on Reset has occurred
0 = A Power-on Reset has not occurred
Note 1: All of the Reset status bits may be set or cleared in software. Setting one of these bits in software does not
cause a device Reset.
2: If the FWDTEN Configuration bit is ‘1’ (unprogrammed), the WDT is always enabled, regardless of the
SWDTEN bit setting.
3: For PIC24HJ256GPX06A/X08A/X10A devices, this bit is unimplemented and reads back programmed
value.
 2009 Microchip Technology Inc.
Preliminary
DS70592B-page 69
PIC24HJXXXGPX06A/X08A/X10A
TABLE 6-1:
RESET FLAG BIT OPERATION
Flag Bit
Setting Event
Clearing Event
TRAPR (RCON<15>)
Trap conflict event
POR, BOR
IOPUWR (RCON<14>)
Illegal opcode or uninitialized
W register access
POR, BOR
EXTR (RCON<7>)
MCLR Reset
POR
SWR (RCON<6>)
RESET instruction
POR, BOR
WDTO (RCON<4>)
WDT time-out
PWRSAV instruction, POR, BOR
SLEEP (RCON<3>)
PWRSAV #SLEEP instruction
POR, BOR
IDLE (RCON<2>)
PWRSAV #IDLE instruction
POR, BOR
BOR (RCON<1>)
BOR, POR
—
POR (RCON<0>)
POR
—
Note:
6.1
All Reset flag bits may be set or cleared by the user software.
Clock Source Selection at Reset
If clock switching is enabled, the system clock source at
device Reset is chosen, as shown in Table 6-2. If clock
switching is disabled, the system clock source is always
selected according to the oscillator Configuration bits.
Refer to Section 9.0 “Oscillator Configuration” for
further details.
TABLE 6-2:
OSCILLATOR SELECTION vs.
TYPE OF RESET (CLOCK
SWITCHING ENABLED)
Reset Type
POR
BOR
MCLR
WDTR
Clock Source Determinant
6.2
Device Reset Times
The Reset times for various types of device Reset are
summarized in Table 6-3. The system Reset signal is
released after the POR and PWRT delay times expire.
The time at which the device actually begins to execute
code also depends on the system oscillator delays,
which include the Oscillator Start-up Timer (OST) and
the PLL lock time. The OST and PLL lock times occur
in parallel with the applicable reset delay times.
The FSCM delay determines the time at which the
FSCM begins to monitor the system clock source after
the reset signal is released.
Oscillator Configuration bits
(FNOSC<2:0>)
COSC Control bits
(OSCCON<14:12>)
SWR
DS70592B-page 70
Preliminary
 2009 Microchip Technology Inc.
PIC24HJXXXGPX06A/X08A/X10A
TABLE 6-3:
Reset Type
POR
RESET DELAY TIMES FOR VARIOUS DEVICE RESETS
SYSRST Delay
System Clock
Delay
FSCM
Delay
EC, FRC, LPRC
TPOR + TSTARTUP + TRST
—
—
Clock Source
Notes
1, 2, 3
ECPLL, FRCPLL
TPOR + TSTARTUP + TRST
TLOCK
TFSCM
1, 2, 3, 5, 6
XT, HS, SOSC
TPOR + TSTARTUP + TRST
TOST
TFSCM
1, 2, 3, 4, 6
XTPLL, HSPLL
TPOR + TSTARTUP + TRST
TOST + TLOCK
TFSCM
1, 2, 3, 4, 5, 6
MCLR
Any Clock
TRST
—
—
3
WDT
Any Clock
TRST
—
—
3
Software
Any clock
TRST
—
—
3
Illegal Opcode
Any Clock
TRST
—
—
3
Uninitialized W
Any Clock
TRST
—
—
3
Trap Conflict
Any Clock
TRST
—
—
3
Note 1:
2:
3:
4:
5:
6:
6.2.1
TPOR = Power-on Reset delay (10 s nominal).
TSTARTUP = Conditional POR delay of 20 s nominal (if on-chip regulator is enabled) or 64 ms nominal
Power-up Timer delay (if regulator is disabled). TSTARTUP is also applied to all returns from powered-down
states, including waking from Sleep mode, only if the regulator is enabled.
TRST = Internal state Reset time (20 s nominal).
TOST = Oscillator Start-up Timer. A 10-bit counter counts 1024 oscillator periods before releasing the
oscillator clock to the system.
TLOCK = PLL lock time (20 s nominal).
TFSCM = Fail-Safe Clock Monitor delay (100 s nominal).
POR AND LONG OSCILLATOR
START-UP TIMES
6.2.2.1
The oscillator start-up circuitry and its associated delay
timers are not linked to the device Reset delays that
occur at power-up. Some crystal circuits (especially
low-frequency crystals) have a relatively long start-up
time. Therefore, one or more of the following conditions
is possible after the Reset signal is released:
• The oscillator circuit has not begun to oscillate.
• The Oscillator Start-up Timer has not expired (if a
crystal oscillator is used).
• The PLL has not achieved a lock (if PLL is used).
The device will not begin to execute code until a valid
clock source has been released to the system. Therefore, the oscillator and PLL start-up delays must be
considered when the Reset delay time must be known.
6.2.2
FAIL-SAFE CLOCK MONITOR
(FSCM) AND DEVICE RESETS
If the FSCM is enabled, it begins to monitor the system
clock source when the Reset signal is released. If a
valid clock source is not available at this time, the
device automatically switches to the FRC oscillator and
the user can switch to the desired crystal oscillator in
the Trap Service Routine.
 2009 Microchip Technology Inc.
FSCM Delay for Crystal and PLL
Clock Sources
When the system clock source is provided by a crystal
oscillator and/or the PLL, a small delay, TFSCM, is automatically inserted after the POR and PWRT delay
times. The FSCM does not begin to monitor the system
clock source until this delay expires. The FSCM delay
time is nominally 500 s and provides additional time
for the oscillator and/or PLL to stabilize. In most cases,
the FSCM delay prevents an oscillator failure trap at a
device Reset when the PWRT is disabled.
6.3
Special Function Register Reset
States
Most of the Special Function Registers (SFRs) associated with the CPU and peripherals are reset to a
particular value at a device Reset. The SFRs are
grouped by their peripheral or CPU function and their
Reset values are specified in each section of this
manual.
The Reset value for each SFR does not depend on the
type of Reset, with the exception of two registers. The
Reset value for the Reset Control register, RCON,
depends on the type of device Reset. The Reset value
for the Oscillator Control register, OSCCON, depends
on the type of Reset and the programmed values of the
oscillator Configuration bits in the FOSC Configuration
register.
Preliminary
DS70592B-page 71
PIC24HJXXXGPX06A/X08A/X10A
NOTES:
DS70592B-page 72
Preliminary
 2009 Microchip Technology Inc.
PIC24HJXXXGPX06A/X08A/X10A
7.0
INTERRUPT CONTROLLER
7.1.1
Note 1: This data sheet summarizes the features
of the PIC24HJXXXGPX06A/X08A/X10A
family of devices. However, it is not
intended to be a comprehensive
reference source. To complement the
information in this data sheet, refer to
Section 6. “Interrupts” (DS70224) of
the “dsPIC33F/PIC24H Family Reference
Manual”, which is available from the
Microchip website (www.microchip.com).
2: Some registers and associated bits
described in this section may not be available on all devices. Refer to Section 4.0
“Memory Organization” in this data
sheet for device-specific register and bit
information.
The PIC24HJXXXGPX06A/X08A/X10A interrupt controller reduces the numerous peripheral interrupt
request signals to a single interrupt request signal to
the PIC24HJXXXGPX06A/X08A/X10A CPU. It has the
following features:
•
•
•
•
Up to 8 processor exceptions and software traps
7 user-selectable priority levels
Interrupt Vector Table (IVT) with up to 118 vectors
A unique vector for each interrupt or exception
source
• Fixed priority within a specified user priority level
• Alternate Interrupt Vector Table (AIVT) for debug
support
• Fixed interrupt entry and return latencies
7.1
ALTERNATE VECTOR TABLE
The Alternate Interrupt Vector Table (AIVT) is located
after the IVT, as shown in Figure 7-1. Access to the
AIVT is provided by the ALTIVT control bit
(INTCON2<15>). If the ALTIVT bit is set, all interrupt
and exception processes use the alternate vectors
instead of the default vectors. The alternate vectors are
organized in the same manner as the default vectors.
The AIVT supports debugging by providing a means to
switch between an application and a support environment without requiring the interrupt vectors to be
reprogrammed. This feature also enables switching
between applications for evaluation of different software algorithms at run time. If the AIVT is not needed,
the AIVT should be programmed with the same
addresses used in the IVT.
7.2
Reset Sequence
A device Reset is not a true exception because the
interrupt controller is not involved in the Reset process.
The PIC24HJXXXGPX06A/X08A/X10A device clears
its registers in response to a Reset which forces the PC
to zero. The digital signal controller then begins program execution at location 0x000000. The user programs a GOTO instruction at the Reset address which
redirects program execution to the appropriate start-up
routine.
Note:
Any unimplemented or unused vector
locations in the IVT and AIVT should be
programmed with the address of a default
interrupt handler routine that contains a
RESET instruction.
Interrupt Vector Table
The Interrupt Vector Table (IVT) is shown in Figure 7-1.
The IVT resides in program memory, starting at location
000004h. The IVT contains 126 vectors consisting of
8 nonmaskable trap vectors plus up to 118 sources of
interrupt. In general, each interrupt source has its own
vector. Each interrupt vector contains a 24-bit wide
address. The value programmed into each interrupt
vector location is the starting address of the associated
Interrupt Service Routine (ISR).
Interrupt vectors are prioritized in terms of their natural
priority; this priority is linked to their position in the
vector table. All other things being equal, lower
addresses have a higher natural priority. For example,
the interrupt associated with vector 0 will take priority
over interrupts at any other vector address.
PIC24HJXXXGPX06A/X08A/X10A devices implement
up to 61 unique interrupts and 5 nonmaskable traps.
These are summarized in Table 7-1 and Table 7-2.
 2009 Microchip Technology Inc.
Preliminary
DS70592B-page 73
PIC24HJXXXGPX06A/X08A/X10A
Decreasing Natural Order Priority
FIGURE 7-1:
Note 1:
DS70592B-page 74
PIC24HJXXXGPX06A/X08A/X10A INTERRUPT VECTOR TABLE
Reset – GOTO Instruction
Reset – GOTO Address
Reserved
Oscillator Fail Trap Vector
Address Error Trap Vector
Stack Error Trap Vector
Math Error Trap Vector
DMA Error Trap Vector
Reserved
Reserved
Interrupt Vector 0
Interrupt Vector 1
~
~
~
Interrupt Vector 52
Interrupt Vector 53
Interrupt Vector 54
~
~
~
Interrupt Vector 116
Interrupt Vector 117
Reserved
Reserved
Reserved
Oscillator Fail Trap Vector
Address Error Trap Vector
Stack Error Trap Vector
Math Error Trap Vector
DMA Error Trap Vector
Reserved
Reserved
Interrupt Vector 0
Interrupt Vector 1
~
~
~
Interrupt Vector 52
Interrupt Vector 53
Interrupt Vector 54
~
~
~
Interrupt Vector 116
Interrupt Vector 117
Start of Code
0x000000
0x000002
0x000004
0x000014
0x00007C
0x00007E
0x000080
Interrupt Vector Table (IVT)(1)
0x0000FC
0x0000FE
0x000100
0x000102
0x000114
Alternate Interrupt Vector Table (AIVT)(1)
0x00017C
0x00017E
0x000180
0x0001FE
0x000200
See Table 7-1 for the list of implemented interrupt vectors.
Preliminary
 2009 Microchip Technology Inc.
PIC24HJXXXGPX06A/X08A/X10A
TABLE 7-1:
INTERRUPT VECTORS
Vector
Number
Interrupt
Request (IRQ)
Number
IVT Address
AIVT Address
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
0
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
0x000014
0x000016
0x000018
0x00001A
0x00001C
0x00001E
0x000020
0x000022
0x000024
0x000026
0x000028
0x00002A
0x00002C
0x00002E
0x000030
0x000032
0x000034
0x000036
0x000038
0x00003A
0x00003C
0x00003E
0x000040
0x000042
0x000044
0x000046
0x000048
0x00004A
0x00004C
0x00004E
0x000050
0x000052
0x000054
0x000056
0x000058
0x00005A
0x00005C
0x00005E
0x000060
0x000062
0x000064
0x000066
0x000068
0x00006A
0x00006C
0x00006E
0x000114
0x000116
0x000118
0x00011A
0x00011C
0x00011E
0x000120
0x000122
0x000124
0x000126
0x000128
0x00012A
0x00012C
0x00012E
0x000130
0x000132
0x000134
0x000136
0x000138
0x00013A
0x00013C
0x00013E
0x000140
0x000142
0x000144
0x000146
0x000148
0x00014A
0x00014C
0x00014E
0x000150
0x000152
0x000154
0x000156
0x000158
0x00015A
0x00015C
0x00015E
0x000160
0x000162
0x000164
0x000166
0x000168
0x00016A
0x00016C
0x00016E
 2009 Microchip Technology Inc.
Preliminary
Interrupt Source
INT0 – External Interrupt 0
IC1 – Input Compare 1
OC1 – Output Compare 1
T1 – Timer1
DMA0 – DMA Channel 0
IC2 – Input Capture 2
OC2 – Output Compare 2
T2 – Timer2
T3 – Timer3
SPI1E – SPI1 Error
SPI1 – SPI1 Transfer Done
U1RX – UART1 Receiver
U1TX – UART1 Transmitter
ADC1 – Analog-to-Digital Converter 1
DMA1 – DMA Channel 1
Reserved
SI2C1 – I2C1 Slave Events
MI2C1 – I2C1 Master Events
Reserved
CN - Change Notification Interrupt
INT1 – External Interrupt 1
ADC2 – Analog-to-Digital Converter 2
IC7 – Input Capture 7
IC8 – Input Capture 8
DMA2 – DMA Channel 2
OC3 – Output Compare 3
OC4 – Output Compare 4
T4 – Timer4
T5 – Timer5
INT2 – External Interrupt 2
U2RX – UART2 Receiver
U2TX – UART2 Transmitter
SPI2E – SPI2 Error
SPI1 – SPI1 Transfer Done
C1RX – ECAN1 Receive Data Ready
C1 – ECAN1 Event
DMA3 – DMA Channel 3
IC3 – Input Capture 3
IC4 – Input Capture 4
IC5 – Input Capture 5
IC6 – Input Capture 6
OC5 – Output Compare 5
OC6 – Output Compare 6
OC7 – Output Compare 7
OC8 – Output Compare 8
Reserved
DS70592B-page 75
PIC24HJXXXGPX06A/X08A/X10A
TABLE 7-1:
INTERRUPT VECTORS (CONTINUED)
Vector
Number
Interrupt
Request (IRQ)
Number
54
55
56
57
58
59
60
61
62
63
64
65-68
46
47
48
49
50
51
52
53
54
55
56
57-60
69
70-72
61
62-64
73
74
75
76
77
78
79
80-125
65
66
67
68
69
70
71
72-117
TABLE 7-2:
IVT Address
AIVT Address
0x000070
0x000072
0x000074
0x000076
0x000078
0x00007A
0x00007C
0x00007E
0x000080
0x000082
0x000084
0x0000860x00008C
0x00008E
0x0000900x000094
0x000096
0x000098
0x00009A
0x00009C
0x00009E
0x0000A0
0x0000A2
0x0000A40x0000FE
0x000170
0x000172
0x000174
0x000176
0x000178
0x00017A
0x00017C
0x00017E
0x000180
0x000182
0x000184
0x0001860x00018C
0x00018E
0x0001900x000194
0x000196
0x000198
0x00019A
0x00019C
0x00019E
0x0001A0
0x0001A2
0x0001A40x0001FE
Interrupt Source
DMA4 – DMA Channel 4
T6 – Timer6
T7 – Timer7
SI2C2 – I2C2 Slave Events
MI2C2 – I2C2 Master Events
T8 – Timer8
T9 – Timer9
INT3 – External Interrupt 3
INT4 – External Interrupt 4
C2RX – ECAN2 Receive Data Ready
C2 – ECAN2 Event
Reserved
DMA5 – DMA Channel 5
Reserved
U1E – UART1 Error
U2E – UART2 Error
Reserved
DMA6 – DMA Channel 6
DMA7 – DMA Channel 7
C1TX – ECAN1 Transmit Data Request
C2TX – ECAN2 Transmit Data Request
Reserved
TRAP VECTORS
Vector Number
IVT Address
AIVT Address
Trap Source
0
0x000004
0x000104
1
0x000006
0x000106
Oscillator Failure
2
0x000008
0x000108
Address Error
Reserved
3
0x00000A
0x00010A
Stack Error
4
0x00000C
0x00010C
Math Error
5
0x00000E
0x00010E
DMA Error Trap
6
0x000010
0x000110
Reserved
7
0x000012
0x000112
Reserved
DS70592B-page 76
Preliminary
 2009 Microchip Technology Inc.
PIC24HJXXXGPX06A/X08A/X10A
7.3
Interrupt Control and Status
Registers
The IPC registers are used to set the interrupt priority
level for each source of interrupt. Each user interrupt
source can be assigned to one of eight priority levels.
PIC24HJXXXGPX06A/X08A/X10A devices implement
a total of 30 registers for the interrupt controller:
•
•
•
•
•
•
INTCON1
INTCON2
IFS0 through IFS4
IEC0 through IEC4
IPC0 through IPC17
INTTREG
Global interrupt control functions are controlled from
INTCON1 and INTCON2. INTCON1 contains the Interrupt Nesting Disable (NSTDIS) bit as well as the control
and status flags for the processor trap sources. The
INTCON2 register controls the external interrupt
request signal behavior and the use of the Alternate
Interrupt Vector Table.
The IFS registers maintain all of the interrupt request
flags. Each source of interrupt has a Status bit, which is
set by the respective peripherals or external signal and
is cleared via software.
The IEC registers maintain all of the interrupt enable
bits. These control bits are used to individually enable
interrupts from the peripherals or external signals.
The INTTREG register contains the associated interrupt vector number and the new CPU interrupt priority
level, which are latched into vector number (VECNUM<6:0>) and Interrupt level (ILR<3:0>) bit fields in
the INTTREG register. The new interrupt priority level
is the priority of the pending interrupt.
The interrupt sources are assigned to the IFSx, IECx
and IPCx registers in the same sequence that they are
listed in Table 7-1. For example, the INT0 (External
Interrupt 0) is shown as having vector number 8 and a
natural order priority of 0. Thus, the INT0IF bit is found
in IFS0<0>, the INT0IE bit in IEC0<0>, and the INT0IP
bits in the first position of IPC0 (IPC0<2:0>).
Although they are not specifically part of the interrupt
control hardware, two of the CPU Control registers contain bits that control interrupt functionality. The CPU
STATUS register, SR, contains the IPL<2:0> bits
(SR<7:5>). These bits indicate the current CPU interrupt priority level. The user can change the current
CPU priority level by writing to the IPL bits.
The CORCON register contains the IPL3 bit which,
together with IPL<2:0>, also indicates the current CPU
priority level. IPL3 is a read-only bit so that trap events
cannot be masked by the user software.
All Interrupt registers are described in Register 7-1
through Register 7-32, in the following pages.
 2009 Microchip Technology Inc.
Preliminary
DS70592B-page 77
PIC24HJXXXGPX06A/X08A/X10A
REGISTER 7-1:
SR: CPU STATUS REGISTER(1)
U-0
U-0
U-0
U-0
U-0
U-0
U-0
R/W-0
—
—
—
—
—
—
—
DC
bit 15
bit 8
R/W-0(3)
R/W-0(3)
IPL2(2)
IPL1
(2)
R/W-0(3)
R-0
R/W-0
R/W-0
R/W-0
R/W-0
IPL0(2)
RA
N
OV
Z
C
bit 7
bit 0
Legend:
C = Clear only bit
R = Readable bit
U = Unimplemented bit, read as ‘0’
S = Set only bit
W = Writable bit
-n = Value at POR
‘1’ = Bit is set
‘0’ = Bit is cleared
x = Bit is unknown
IPL<2:0>: CPU Interrupt Priority Level Status bits(2)
111 = CPU Interrupt Priority Level is 7 (15), user interrupts disabled
110 = CPU Interrupt Priority Level is 6 (14)
101 = CPU Interrupt Priority Level is 5 (13)
100 = CPU Interrupt Priority Level is 4 (12)
011 = CPU Interrupt Priority Level is 3 (11)
010 = CPU Interrupt Priority Level is 2 (10)
001 = CPU Interrupt Priority Level is 1 (9)
000 = CPU Interrupt Priority Level is 0 (8)
bit 7-5
Note 1: For complete register details, see Register 3-1.
2: The IPL<2:0> bits are concatenated with the IPL<3> bit (CORCON<3>) to form the CPU Interrupt Priority
Level. The value in parentheses indicates the IPL if IPL<3> = 1. User interrupts are disabled when
IPL<3> = 1.
3: The IPL<2:0> Status bits are read-only when NSTDIS (INTCON1<15>) = 1.
REGISTER 7-2:
CORCON: CORE CONTROL REGISTER(1)
U-0
—
bit 15
U-0
—
U-0
—
U-0
—
U-0
—
U-0
—
U-0
—
U-0
—
U-0
—
bit 8
U-0
—
U-0
—
R/C-0
IPL3(2)
R/W-0
PSV
U-0
—
bit 7
U-0
—
bit 0
Legend:
R = Readable bit
0’ = Bit is cleared
bit 3
U-0
—
C = Clear only bit
W = Writable bit
‘x = Bit is unknown
-n = Value at POR
‘1’ = Bit is set
U = Unimplemented bit, read as ‘0’
IPL3: CPU Interrupt Priority Level Status bit 3(2)
1 = CPU interrupt priority level is greater than 7
0 = CPU interrupt priority level is 7 or less
Note 1: For complete register details, see Register 3-2.
2: The IPL3 bit is concatenated with the IPL<2:0> bits (SR<7:5>) to form the CPU Interrupt Priority Level.
DS70592B-page 78
Preliminary
 2009 Microchip Technology Inc.
PIC24HJXXXGPX06A/X08A/X10A
REGISTER 7-3:
INTCON1: INTERRUPT CONTROL REGISTER 1
R/W-0
U-0
U-0
U-0
U-0
U-0
U-0
U-0
NSTDIS
—
—
—
—
—
—
—
bit 15
bit 8
U-0
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
U-0
—
DIV0ERR
DMACERR
MATHERR
ADDRERR
STKERR
OSCFAIL
—
bit 7
bit 0
Legend:
R = Readable bit
W = Writable bit
U = Unimplemented bit, read as ‘0’
-n = Value at POR
‘1’ = Bit is set
‘0’ = Bit is cleared
bit 15
NSTDIS: Interrupt Nesting Disable bit
1 = Interrupt nesting is disabled
0 = Interrupt nesting is enabled
bit 14-7
Unimplemented: Read as ‘0’
bit 6
DIV0ERR: Arithmetic Error Status bit
1 = Math error trap was caused by a divide by zero
0 = Math error trap was not caused by a divide by zero
bit 5
DMACERR: DMA Controller Error Status bit
1 = DMA controller error trap has occurred
0 = DMA controller error trap has not occurred
bit 4
MATHERR: Arithmetic Error Status bit
1 = Math error trap has occurred
0 = Math error trap has not occurred
bit 3
ADDRERR: Address Error Trap Status bit
1 = Address error trap has occurred
0 = Address error trap has not occurred
bit 2
STKERR: Stack Error Trap Status bit
1 = Stack error trap has occurred
0 = Stack error trap has not occurred
bit 1
OSCFAIL: Oscillator Failure Trap Status bit
1 = Oscillator failure trap has occurred
0 = Oscillator failure trap has not occurred
bit 0
Unimplemented: Read as ‘0’
 2009 Microchip Technology Inc.
Preliminary
x = Bit is unknown
DS70592B-page 79
PIC24HJXXXGPX06A/X08A/X10A
REGISTER 7-4:
INTCON2: INTERRUPT CONTROL REGISTER 2
R/W-0
R-0
U-0
U-0
U-0
U-0
U-0
U-0
ALTIVT
DISI
—
—
—
—
—
—
bit 15
bit 8
U-0
U-0
U-0
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
—
—
—
INT4EP
INT3EP
INT2EP
INT1EP
INT0EP
bit 7
bit 0
Legend:
R = Readable bit
W = Writable bit
U = Unimplemented bit, read as ‘0’
-n = Value at POR
‘1’ = Bit is set
‘0’ = Bit is cleared
bit 15
ALTIVT: Enable Alternate Interrupt Vector Table bit
1 = Use alternate vector table
0 = Use standard (default) vector table
bit 14
DISI: DISI Instruction Status bit
1 = DISI instruction is active
0 = DISI instruction is not active
bit 13-5
Unimplemented: Read as ‘0’
bit 4
INT4EP: External Interrupt 4 Edge Detect Polarity Select bit
1 = Interrupt on negative edge
0 = Interrupt on positive edge
bit 3
INT3EP: External Interrupt 3 Edge Detect Polarity Select bit
1 = Interrupt on negative edge
0 = Interrupt on positive edge
bit 2
INT2EP: External Interrupt 2 Edge Detect Polarity Select bit
1 = Interrupt on negative edge
0 = Interrupt on positive edge
bit 1
INT1EP: External Interrupt 1 Edge Detect Polarity Select bit
1 = Interrupt on negative edge
0 = Interrupt on positive edge
bit 0
INT0EP: External Interrupt 0 Edge Detect Polarity Select bit
1 = Interrupt on negative edge
0 = Interrupt on positive edge
DS70592B-page 80
Preliminary
x = Bit is unknown
 2009 Microchip Technology Inc.
PIC24HJXXXGPX06A/X08A/X10A
REGISTER 7-5:
IFS0: INTERRUPT FLAG STATUS REGISTER 0
U-0
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
—
DMA1IF
AD1IF
U1TXIF
U1RXIF
SPI1IF
SPI1EIF
T3IF
bit 15
bit 8
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
T2IF
OC2IF
IC2IF
DMA01IF
T1IF
OC1IF
IC1IF
INT0IF
bit 7
bit 0
Legend:
R = Readable bit
W = Writable bit
U = Unimplemented bit, read as ‘0’
-n = Value at POR
‘1’ = Bit is set
‘0’ = Bit is cleared
x = Bit is unknown
bit 15
Unimplemented: Read as ‘0’
bit 14
DMA1IF: DMA Channel 1 Data Transfer Complete Interrupt Flag Status bit
1 = Interrupt request has occurred
0 = Interrupt request has not occurred
bit 13
AD1IF: ADC1 Conversion Complete Interrupt Flag Status bit
1 = Interrupt request has occurred
0 = Interrupt request has not occurred
bit 12
U1TXIF: UART1 Transmitter Interrupt Flag Status bit
1 = Interrupt request has occurred
0 = Interrupt request has not occurred
bit 11
U1RXIF: UART1 Receiver Interrupt Flag Status bit
1 = Interrupt request has occurred
0 = Interrupt request has not occurred
bit 10
SPI1IF: SPI1 Event Interrupt Flag Status bit
1 = Interrupt request has occurred
0 = Interrupt request has not occurred
bit 9
SPI1EIF: SPI1 Fault Interrupt Flag Status bit
1 = Interrupt request has occurred
0 = Interrupt request has not occurred
bit 8
T3IF: Timer3 Interrupt Flag Status bit
1 = Interrupt request has occurred
0 = Interrupt request has not occurred
bit 7
T2IF: Timer2 Interrupt Flag Status bit
1 = Interrupt request has occurred
0 = Interrupt request has not occurred
bit 6
OC2IF: Output Compare Channel 2 Interrupt Flag Status bit
1 = Interrupt request has occurred
0 = Interrupt request has not occurred
bit 5
IC2IF: Input Capture Channel 2 Interrupt Flag Status bit
1 = Interrupt request has occurred
0 = Interrupt request has not occurred
bit 4
DMA01IF: DMA Channel 0 Data Transfer Complete Interrupt Flag Status bit
1 = Interrupt request has occurred
0 = Interrupt request has not occurred
bit 3
T1IF: Timer1 Interrupt Flag Status bit
1 = Interrupt request has occurred
0 = Interrupt request has not occurred
 2009 Microchip Technology Inc.
Preliminary
DS70592B-page 81
PIC24HJXXXGPX06A/X08A/X10A
REGISTER 7-5:
IFS0: INTERRUPT FLAG STATUS REGISTER 0 (CONTINUED)
bit 2
OC1IF: Output Compare Channel 1 Interrupt Flag Status bit
1 = Interrupt request has occurred
0 = Interrupt request has not occurred
bit 1
IC1IF: Input Capture Channel 1 Interrupt Flag Status bit
1 = Interrupt request has occurred
0 = Interrupt request has not occurred
bit 0
INT0IF: External Interrupt 0 Flag Status bit
1 = Interrupt request has occurred
0 = Interrupt request has not occurred
DS70592B-page 82
Preliminary
 2009 Microchip Technology Inc.
PIC24HJXXXGPX06A/X08A/X10A
REGISTER 7-6:
IFS1: INTERRUPT FLAG STATUS REGISTER 1
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
U2TXIF
U2RXIF
INT2IF
T5IF
T4IF
OC4IF
OC3IF
DMA21IF
bit 15
bit 8
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
U-0
R/W-0
R/W-0
IC8IF
IC7IF
AD2IF
INT1IF
CNIF
—
MI2C1IF
SI2C1IF
bit 7
bit 0
Legend:
R = Readable bit
W = Writable bit
U = Unimplemented bit, read as ‘0’
-n = Value at POR
‘1’ = Bit is set
‘0’ = Bit is cleared
x = Bit is unknown
bit 15
U2TXIF: UART2 Transmitter Interrupt Flag Status bit
1 = Interrupt request has occurred
0 = Interrupt request has not occurred
bit 14
U2RXIF: UART2 Receiver Interrupt Flag Status bit
1 = Interrupt request has occurred
0 = Interrupt request has not occurred
bit 13
INT2IF: External Interrupt 2 Flag Status bit
1 = Interrupt request has occurred
0 = Interrupt request has not occurred
bit 12
T5IF: Timer5 Interrupt Flag Status bit
1 = Interrupt request has occurred
0 = Interrupt request has not occurred
bit 11
T4IF: Timer4 Interrupt Flag Status bit
1 = Interrupt request has occurred
0 = Interrupt request has not occurred
bit 10
OC4IF: Output Compare Channel 4 Interrupt Flag Status bit
1 = Interrupt request has occurred
0 = Interrupt request has not occurred
bit 9
OC3IF: Output Compare Channel 3 Interrupt Flag Status bit
1 = Interrupt request has occurred
0 = Interrupt request has not occurred
bit 8
DMA21IF: DMA Channel 2 Data Transfer Complete Interrupt Flag Status bit
1 = Interrupt request has occurred
0 = Interrupt request has not occurred
bit 7
IC8IF: Input Capture Channel 8 Interrupt Flag Status bit
1 = Interrupt request has occurred
0 = Interrupt request has not occurred
bit 6
IC7IF: Input Capture Channel 7 Interrupt Flag Status bit
1 = Interrupt request has occurred
0 = Interrupt request has not occurred
bit 5
AD2IF: ADC2 Conversion Complete Interrupt Flag Status bit
1 = Interrupt request has occurred
0 = Interrupt request has not occurred
bit 4
INT1IF: External Interrupt 1 Flag Status bit
1 = Interrupt request has occurred
0 = Interrupt request has not occurred
 2009 Microchip Technology Inc.
Preliminary
DS70592B-page 83
PIC24HJXXXGPX06A/X08A/X10A
REGISTER 7-6:
IFS1: INTERRUPT FLAG STATUS REGISTER 1 (CONTINUED)
bit 3
CNIF: Input Change Notification Interrupt Flag Status bit
1 = Interrupt request has occurred
0 = Interrupt request has not occurred
bit 2
Unimplemented: Read as ‘0’
bit 1
MI2C1IF: I2C1 Master Events Interrupt Flag Status bit
1 = Interrupt request has occurred
0 = Interrupt request has not occurred
bit 0
SI2C1IF: I2C1 Slave Events Interrupt Flag Status bit
1 = Interrupt request has occurred
0 = Interrupt request has not occurred
DS70592B-page 84
Preliminary
 2009 Microchip Technology Inc.
PIC24HJXXXGPX06A/X08A/X10A
REGISTER 7-7:
IFS2: INTERRUPT FLAG STATUS REGISTER 2
R/W-0
R/W-0
U-0
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
T6IF
DMA4IF
—
OC8IF
OC7IF
OC6IF
OC5IF
IC6IF
bit 15
bit 8
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
IC5IF
IC4IF
IC3IF
DMA3IF
C1IF
C1RXIF
SPI2IF
SPI2EIF
bit 7
bit 0
Legend:
R = Readable bit
W = Writable bit
U = Unimplemented bit, read as ‘0’
-n = Value at POR
‘1’ = Bit is set
‘0’ = Bit is cleared
x = Bit is unknown
bit 15
T6IF: Timer6 Interrupt Flag Status bit
1 = Interrupt request has occurred
0 = Interrupt request has not occurred
bit 14
DMA4IF: DMA Channel 4 Data Transfer Complete Interrupt Flag Status bit
1 = Interrupt request has occurred
0 = Interrupt request has not occurred
bit 13
Unimplemented: Read as ‘0’
bit 12
OC8IF: Output Compare Channel 8 Interrupt Flag Status bit
1 = Interrupt request has occurred
0 = Interrupt request has not occurred
bit 11
OC7IF: Output Compare Channel 7 Interrupt Flag Status bit
1 = Interrupt request has occurred
0 = Interrupt request has not occurred
bit 10
OC6IF: Output Compare Channel 6 Interrupt Flag Status bit
1 = Interrupt request has occurred
0 = Interrupt request has not occurred
bit 9
OC5IF: Output Compare Channel 5 Interrupt Flag Status bit
1 = Interrupt request has occurred
0 = Interrupt request has not occurred
bit 8
IC6IF: Input Capture Channel 6 Interrupt Flag Status bit
1 = Interrupt request has occurred
0 = Interrupt request has not occurred
bit 7
IC5IF: Input Capture Channel 5 Interrupt Flag Status bit
1 = Interrupt request has occurred
0 = Interrupt request has not occurred
bit 6
IC4IF: Input Capture Channel 4 Interrupt Flag Status bit
1 = Interrupt request has occurred
0 = Interrupt request has not occurred
bit 5
IC3IF: Input Capture Channel 3 Interrupt Flag Status bit
1 = Interrupt request has occurred
0 = Interrupt request has not occurred
bit 4
DMA3IF: DMA Channel 3 Data Transfer Complete Interrupt Flag Status bit
1 = Interrupt request has occurred
0 = Interrupt request has not occurred
bit 3
C1IF: ECAN1 Event Interrupt Flag Status bit
1 = Interrupt request has occurred
0 = Interrupt request has not occurred
 2009 Microchip Technology Inc.
Preliminary
DS70592B-page 85
PIC24HJXXXGPX06A/X08A/X10A
REGISTER 7-7:
IFS2: INTERRUPT FLAG STATUS REGISTER 2 (CONTINUED)
bit 2
C1RXIF: ECAN1 Receive Data Ready Interrupt Flag Status bit
1 = Interrupt request has occurred
0 = Interrupt request has not occurred
bit 1
SPI2IF: SPI2 Event Interrupt Flag Status bit
1 = Interrupt request has occurred
0 = Interrupt request has not occurred
bit 0
SPI2EIF: SPI2 Error Interrupt Flag Status bit
1 = Interrupt request has occurred
0 = Interrupt request has not occurred
DS70592B-page 86
Preliminary
 2009 Microchip Technology Inc.
PIC24HJXXXGPX06A/X08A/X10A
REGISTER 7-8:
IFS3: INTERRUPT FLAG STATUS REGISTER 3
U-0
U-0
R/W-0
U-0
U-0
U-0
U-0
R/W-0
—
—
DMA5IF
—
—
—
—
C2IF
bit 15
bit 8
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
C2RXIF
INT4IF
INT3IF
T9IF
T8IF
MI2C2IF
SI2C2IF
T7IF
bit 7
bit 0
Legend:
R = Readable bit
W = Writable bit
U = Unimplemented bit, read as ‘0’
-n = Value at POR
‘1’ = Bit is set
‘0’ = Bit is cleared
x = Bit is unknown
bit 15-14
Unimplemented: Read as ‘0’
bit 13
DMA5IF: DMA Channel 5 Data Transfer Complete Interrupt Flag Status bit
1 = Interrupt request has occurred
0 = Interrupt request has not occurred
bit 12-9
Unimplemented: Read as ‘0’
bit 8
C2IF: ECAN2 Event Interrupt Flag Status bit
1 = Interrupt request has occurred
0 = Interrupt request has not occurred
bit 7
C2RXIF: ECAN2 Receive Data Ready Interrupt Flag Status bit
1 = Interrupt request has occurred
0 = Interrupt request has not occurred
bit 6
INT4IF: External Interrupt 4 Flag Status bit
1 = Interrupt request has occurred
0 = Interrupt request has not occurred
bit 5
INT3IF: External Interrupt 3 Flag Status bit
1 = Interrupt request has occurred
0 = Interrupt request has not occurred
bit 4
T9IF: Timer9 Interrupt Flag Status bit
1 = Interrupt request has occurred
0 = Interrupt request has not occurred
bit 3
T8IF: Timer8 Interrupt Flag Status bit
1 = Interrupt request has occurred
0 = Interrupt request has not occurred
bit 2
MI2C2IF: I2C2 Master Events Interrupt Flag Status bit
1 = Interrupt request has occurred
0 = Interrupt request has not occurred
bit 1
SI2C2IF: I2C2 Slave Events Interrupt Flag Status bit
1 = Interrupt request has occurred
0 = Interrupt request has not occurred
bit 0
T7IF: Timer7 Interrupt Flag Status bit
1 = Interrupt request has occurred
0 = Interrupt request has not occurred
 2009 Microchip Technology Inc.
Preliminary
DS70592B-page 87
PIC24HJXXXGPX06A/X08A/X10A
REGISTER 7-9:
IFS4: INTERRUPT FLAG STATUS REGISTER 4
U-0
U-0
U-0
U-0
U-0
U-0
U-0
U-0
—
—
—
—
—
—
—
—
bit 15
bit 8
R/W-0
R/W-0
R/W-0
R/W-0
U-0
R/W-0
R/W-0
U-0
C2TXIF
C1TXIF
DMA7IF
DMA6IF
—
U2EIF
U1EIF
—
bit 7
bit 0
Legend:
R = Readable bit
W = Writable bit
U = Unimplemented bit, read as ‘0’
-n = Value at POR
‘1’ = Bit is set
‘0’ = Bit is cleared
x = Bit is unknown
bit 15-8
Unimplemented: Read as ‘0’
bit 7
C2TXIF: ECAN2 Transmit Data Request Interrupt Flag Status bit
1 = Interrupt request has occurred
0 = Interrupt request has not occurred
bit 6
C1TXIF: ECAN1 Transmit Data Request Interrupt Flag Status bit
1 = Interrupt request has occurred
0 = Interrupt request has not occurred
bit 5
DMA7IF: DMA Channel 7 Data Transfer Complete Interrupt Flag Status bit
1 = Interrupt request has occurred
0 = Interrupt request has not occurred
bit 4
DMA6IF: DMA Channel 6 Data Transfer Complete Interrupt Flag Status bit
1 = Interrupt request has occurred
0 = Interrupt request has not occurred
bit 3
Unimplemented: Read as ‘0’
bit 2
U2EIF: UART2 Error Interrupt Flag Status bit
1 = Interrupt request has occurred
0 = Interrupt request has not occurred
bit 1
U1EIF: UART1 Error Interrupt Flag Status bit
1 = Interrupt request has occurred
0 = Interrupt request has not occurred
bit 0
Unimplemented: Read as ‘0’
DS70592B-page 88
Preliminary
 2009 Microchip Technology Inc.
PIC24HJXXXGPX06A/X08A/X10A
REGISTER 7-10:
IEC0: INTERRUPT ENABLE CONTROL REGISTER 0
U-0
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
—
DMA1IE
AD1IE
U1TXIE
U1RXIE
SPI1IE
SPI1EIE
T3IE
bit 15
bit 8
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
T2IE
OC2IE
IC2IE
DMA0IE
T1IE
OC1IE
IC1IE
INT0IE
bit 7
bit 0
Legend:
R = Readable bit
W = Writable bit
U = Unimplemented bit, read as ‘0’
-n = Value at POR
‘1’ = Bit is set
‘0’ = Bit is cleared
bit 15
Unimplemented: Read as ‘0’
bit 14
DMA1IE: DMA Channel 1 Data Transfer Complete Interrupt Enable bit
1 = Interrupt request enabled
0 = Interrupt request not enabled
bit 13
AD1IE: ADC1 Conversion Complete Interrupt Enable bit
1 = Interrupt request enabled
0 = Interrupt request not enabled
bit 12
U1TXIE: UART1 Transmitter Interrupt Enable bit
1 = Interrupt request enabled
0 = Interrupt request not enabled
bit 11
U1RXIE: UART1 Receiver Interrupt Enable bit
1 = Interrupt request enabled
0 = Interrupt request not enabled
bit 10
SPI1IE: SPI1 Event Interrupt Enable bit
1 = Interrupt request enabled
0 = Interrupt request not enabled
bit 9
SPI1EIE: SPI1 Error Interrupt Enable bit
1 = Interrupt request enabled
0 = Interrupt request not enabled
bit 8
T3IE: Timer3 Interrupt Enable bit
1 = Interrupt request enabled
0 = Interrupt request not enabled
bit 7
T2IE: Timer2 Interrupt Enable bit
1 = Interrupt request enabled
0 = Interrupt request not enabled
bit 6
OC2IE: Output Compare Channel 2 Interrupt Enable bit
1 = Interrupt request enabled
0 = Interrupt request not enabled
bit 5
IC2IE: Input Capture Channel 2 Interrupt Enable bit
1 = Interrupt request enabled
0 = Interrupt request not enabled
bit 4
DMA0IE: DMA Channel 0 Data Transfer Complete Interrupt Enable bit
1 = Interrupt request enabled
0 = Interrupt request not enabled
bit 3
T1IE: Timer1 Interrupt Enable bit
1 = Interrupt request enabled
0 = Interrupt request not enabled
 2009 Microchip Technology Inc.
Preliminary
x = Bit is unknown
DS70592B-page 89
PIC24HJXXXGPX06A/X08A/X10A
REGISTER 7-10:
IEC0: INTERRUPT ENABLE CONTROL REGISTER 0 (CONTINUED)
bit 2
OC1IE: Output Compare Channel 1 Interrupt Enable bit
1 = Interrupt request enabled
0 = Interrupt request not enabled
bit 1
IC1IE: Input Capture Channel 1 Interrupt Enable bit
1 = Interrupt request enabled
0 = Interrupt request not enabled
bit 0
INT0IE: External Interrupt 0 Enable bit
1 = Interrupt request enabled
0 = Interrupt request not enabled
DS70592B-page 90
Preliminary
 2009 Microchip Technology Inc.
PIC24HJXXXGPX06A/X08A/X10A
REGISTER 7-11:
IEC1: INTERRUPT ENABLE CONTROL REGISTER 1
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
U2TXIE
U2RXIE
INT2IE
T5IE
T4IE
OC4IE
OC3IE
DMA2IE
bit 15
bit 8
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
U-0
R/W-0
R/W-0
IC8IE
IC7IE
AD2IE
INT1IE
CNIE
—
MI2C1IE
SI2C1IE
bit 7
bit 0
Legend:
R = Readable bit
W = Writable bit
U = Unimplemented bit, read as ‘0’
-n = Value at POR
‘1’ = Bit is set
‘0’ = Bit is cleared
bit 15
U2TXIE: UART2 Transmitter Interrupt Enable bit
1 = Interrupt request enabled
0 = Interrupt request not enabled
bit 14
U2RXIE: UART2 Receiver Interrupt Enable bit
1 = Interrupt request enabled
0 = Interrupt request not enabled
bit 13
INT2IE: External Interrupt 2 Enable bit
1 = Interrupt request enabled
0 = Interrupt request not enabled
bit 12
T5IE: Timer5 Interrupt Enable bit
1 = Interrupt request enabled
0 = Interrupt request not enabled
bit 11
T4IE: Timer4 Interrupt Enable bit
1 = Interrupt request enabled
0 = Interrupt request not enabled
bit 10
OC4IE: Output Compare Channel 4 Interrupt Enable bit
1 = Interrupt request enabled
0 = Interrupt request not enabled
bit 9
OC3IE: Output Compare Channel 3 Interrupt Enable bit
1 = Interrupt request enabled
0 = Interrupt request not enabled
bit 8
DMA2IE: DMA Channel 2 Data Transfer Complete Interrupt Enable bit
1 = Interrupt request enabled
0 = Interrupt request not enabled
bit 7
IC8IE: Input Capture Channel 8 Interrupt Enable bit
1 = Interrupt request enabled
0 = Interrupt request not enabled
bit 6
IC7IE: Input Capture Channel 7 Interrupt Enable bit
1 = Interrupt request enabled
0 = Interrupt request not enabled
bit 5
AD2IE: ADC2 Conversion Complete Interrupt Enable bit
1 = Interrupt request enabled
0 = Interrupt request not enabled
bit 4
INT1IE: External Interrupt 1 Enable bit
1 = Interrupt request enabled
0 = Interrupt request not enabled
 2009 Microchip Technology Inc.
Preliminary
x = Bit is unknown
DS70592B-page 91
PIC24HJXXXGPX06A/X08A/X10A
REGISTER 7-11:
IEC1: INTERRUPT ENABLE CONTROL REGISTER 1 (CONTINUED)
bit 3
CNIE: Input Change Notification Interrupt Enable bit
1 = Interrupt request enabled
0 = Interrupt request not enabled
bit 2
Unimplemented: Read as ‘0’
bit 1
MI2C1IE: I2C1 Master Events Interrupt Enable bit
1 = Interrupt request enabled
0 = Interrupt request not enabled
bit 0
SI2C1IE: I2C1 Slave Events Interrupt Enable bit
1 = Interrupt request enabled
0 = Interrupt request not enabled
DS70592B-page 92
Preliminary
 2009 Microchip Technology Inc.
PIC24HJXXXGPX06A/X08A/X10A
REGISTER 7-12:
IEC2: INTERRUPT ENABLE CONTROL REGISTER 2
R/W-0
R/W-0
U-0
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
T6IE
DMA4IE
—
OC8IE
OC7IE
OC6IE
OC5IE
IC6IE
bit 15
bit 8
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
IC5IE
IC4IE
IC3IE
DMA3IE
C1IE
C1RXIE
SPI2IE
SPI2EIE
bit 7
bit 0
Legend:
R = Readable bit
W = Writable bit
U = Unimplemented bit, read as ‘0’
-n = Value at POR
‘1’ = Bit is set
‘0’ = Bit is cleared
bit 15
T6IE: Timer6 Interrupt Enable bit
1 = Interrupt request enabled
0 = Interrupt request not enabled
bit 14
DMA4IE: DMA Channel 4 Data Transfer Complete Interrupt Enable bit
1 = Interrupt request enabled
0 = Interrupt request not enabled
bit 13
Unimplemented: Read as ‘0’
bit 12
OC8IE: Output Compare Channel 8 Interrupt Enable bit
1 = Interrupt request enabled
0 = Interrupt request not enabled
bit 11
OC7IE: Output Compare Channel 7 Interrupt Enable bit
1 = Interrupt request enabled
0 = Interrupt request not enabled
bit 10
OC6IE: Output Compare Channel 6 Interrupt Enable bit
1 = Interrupt request enabled
0 = Interrupt request not enabled
bit 9
OC5IE: Output Compare Channel 5 Interrupt Enable bit
1 = Interrupt request enabled
0 = Interrupt request not enabled
bit 8
IC6IE: Input Capture Channel 6 Interrupt Enable bit
1 = Interrupt request enabled
0 = Interrupt request not enabled
bit 7
IC5IE: Input Capture Channel 5 Interrupt Enable bit
1 = Interrupt request enabled
0 = Interrupt request not enabled
bit 6
IC4IE: Input Capture Channel 4 Interrupt Enable bit
1 = Interrupt request enabled
0 = Interrupt request not enabled
bit 5
IC3IE: Input Capture Channel 3 Interrupt Enable bit
1 = Interrupt request enabled
0 = Interrupt request not enabled
bit 4
DMA3IE: DMA Channel 3 Data Transfer Complete Interrupt Enable bit
1 = Interrupt request enabled
0 = Interrupt request not enabled
bit 3
C1IE: ECAN1 Event Interrupt Enable bit
1 = Interrupt request enabled
0 = Interrupt request not enabled
 2009 Microchip Technology Inc.
Preliminary
x = Bit is unknown
DS70592B-page 93
PIC24HJXXXGPX06A/X08A/X10A
REGISTER 7-12:
IEC2: INTERRUPT ENABLE CONTROL REGISTER 2 (CONTINUED)
bit 2
C1RXIE: ECAN1 Receive Data Ready Interrupt Enable bit
1 = Interrupt request enabled
0 = Interrupt request not enabled
bit 1
SPI2IE: SPI2 Event Interrupt Enable bit
1 = Interrupt request enabled
0 = Interrupt request not enabled
bit 0
SPI2EIE: SPI2 Error Interrupt Enable bit
1 = Interrupt request enabled
0 = Interrupt request not enabled
DS70592B-page 94
Preliminary
 2009 Microchip Technology Inc.
PIC24HJXXXGPX06A/X08A/X10A
REGISTER 7-13:
IEC3: INTERRUPT ENABLE CONTROL REGISTER 3
U-0
U-0
R/W-0
U-0
U-0
U-0
U-0
R/W-0
—
—
DMA5IE
—
—
—
—
C2IE
bit 15
bit 8
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
C2RXIE
INT4IE
INT3IE
T9IE
T8IE
MI2C2IE
SI2C2IE
T7IE
bit 7
bit 0
Legend:
R = Readable bit
W = Writable bit
U = Unimplemented bit, read as ‘0’
-n = Value at POR
‘1’ = Bit is set
‘0’ = Bit is cleared
bit 15-14
Unimplemented: Read as ‘0’
bit 13
DMA5IE: DMA Channel 5 Data Transfer Complete Interrupt Enable bit
1 = Interrupt request enabled
0 = Interrupt request not enabled
bit 12-9
Unimplemented: Read as ‘0’
bit 8
C2IE: ECAN2 Event Interrupt Enable bit
1 = Interrupt request enabled
0 = Interrupt request not enabled
bit 7
C2RXIE: ECAN2 Receive Data Ready Interrupt Enable bit
1 = Interrupt request enabled
0 = Interrupt request not enabled
bit 6
INT4IE: External Interrupt 4 Enable bit
1 = Interrupt request enabled
0 = Interrupt request not enabled
bit 5
INT3IE: External Interrupt 3 Enable bit
1 = Interrupt request enabled
0 = Interrupt request not enabled
bit 4
T9IE: Timer9 Interrupt Enable bit
1 = Interrupt request enabled
0 = Interrupt request not enabled
bit 3
T8IE: Timer8 Interrupt Enable bit
1 = Interrupt request enabled
0 = Interrupt request not enabled
bit 2
MI2C2IE: I2C2 Master Events Interrupt Enable bit
1 = Interrupt request enabled
0 = Interrupt request not enabled
bit 1
SI2C2IE: I2C2 Slave Events Interrupt Enable bit
1 = Interrupt request enabled
0 = Interrupt request not enabled
bit 0
T7IE: Timer7 Interrupt Enable bit
1 = Interrupt request enabled
0 = Interrupt request not enabled
 2009 Microchip Technology Inc.
Preliminary
x = Bit is unknown
DS70592B-page 95
PIC24HJXXXGPX06A/X08A/X10A
REGISTER 7-14:
IEC4: INTERRUPT ENABLE CONTROL REGISTER 4
U-0
U-0
U-0
U-0
U-0
U-0
U-0
U-0
—
—
—
—
—
—
—
—
bit 15
bit 8
R/W-0
R/W-0
R/W-0
R/W-0
U-0
R/W-0
R/W-0
U-0
C2TXIE
C1TXIE
DMA7IE
DMA6IE
—
U2EIE
U1EIE
—
bit 7
bit 0
Legend:
R = Readable bit
W = Writable bit
U = Unimplemented bit, read as ‘0’
-n = Value at POR
‘1’ = Bit is set
‘0’ = Bit is cleared
bit 15-8
Unimplemented: Read as ‘0’
bit 7
C2TXIE: ECAN2 Transmit Data Request Interrupt Enable bit
1 = Interrupt request enabled
0 = Interrupt request not enabled
bit 6
C1TXIE: ECAN1 Transmit Data Request Interrupt Enable bit
1 = Interrupt request enabled
0 = Interrupt request not enabled
bit 5
DMA7IE: DMA Channel 7 Data Transfer Complete Enable Status bit
1 = Interrupt request enabled
0 = Interrupt request not enabled
bit 4
DMA6IE: DMA Channel 6 Data Transfer Complete Enable Status bit
1 = Interrupt request enabled
0 = Interrupt request not enabled
bit 3
Unimplemented: Read as ‘0’
bit 2
U2EIE: UART2 Error Interrupt Enable bit
1 = Interrupt request enabled
0 = Interrupt request not enabled
bit 1
U1EIE: UART1 Error Interrupt Enable bit
1 = Interrupt request enabled
0 = Interrupt request not enabled
bit 0
Unimplemented: Read as ‘0’
DS70592B-page 96
Preliminary
x = Bit is unknown
 2009 Microchip Technology Inc.
PIC24HJXXXGPX06A/X08A/X10A
REGISTER 7-15:
U-0
IPC0: INTERRUPT PRIORITY CONTROL REGISTER 0
R/W-1
—
R/W-0
R/W-0
T1IP<2:0>
U-0
R/W-1
—
R/W-0
R/W-0
OC1IP<2:0>
bit 15
bit 8
U-0
R/W-1
—
R/W-0
IC1IP<2:0>
R/W-0
U-0
R/W-1
—
R/W-0
R/W-0
INT0IP<2:0>
bit 7
bit 0
Legend:
R = Readable bit
W = Writable bit
U = Unimplemented bit, read as ‘0’
-n = Value at POR
‘1’ = Bit is set
‘0’ = Bit is cleared
bit 15
Unimplemented: Read as ‘0’
bit 14-12
T1IP<2:0>: Timer1 Interrupt Priority bits
111 = Interrupt is priority 7 (highest priority interrupt)
•
•
•
001 = Interrupt is priority 1
000 = Interrupt source is disabled
bit 11
Unimplemented: Read as ‘0’
bit 10-8
OC1IP<2:0>: Output Compare Channel 1 Interrupt Priority bits
111 = Interrupt is priority 7 (highest priority interrupt)
•
•
•
001 = Interrupt is priority 1
000 = Interrupt source is disabled
bit 7
Unimplemented: Read as ‘0’
bit 6-4
IC1IP<2:0>: Input Capture Channel 1 Interrupt Priority bits
111 = Interrupt is priority 7 (highest priority interrupt)
•
•
•
001 = Interrupt is priority 1
000 = Interrupt source is disabled
bit 3
Unimplemented: Read as ‘0’
bit 2-0
INT0IP<2:0>: External Interrupt 0 Priority bits
111 = Interrupt is priority 7 (highest priority interrupt)
•
•
•
001 = Interrupt is priority 1
000 = Interrupt source is disabled
 2009 Microchip Technology Inc.
Preliminary
x = Bit is unknown
DS70592B-page 97
PIC24HJXXXGPX06A/X08A/X10A
REGISTER 7-16:
U-0
IPC1: INTERRUPT PRIORITY CONTROL REGISTER 1
R/W-1
—
R/W-0
R/W-0
T2IP<2:0>
U-0
R/W-1
—
R/W-0
R/W-0
OC2IP<2:0>
bit 15
bit 8
U-0
R/W-1
—
R/W-0
IC2IP<2:0>
R/W-0
U-0
R/W-1
—
R/W-0
R/W-0
DMA0IP<2:0>
bit 7
bit 0
Legend:
R = Readable bit
W = Writable bit
U = Unimplemented bit, read as ‘0’
-n = Value at POR
‘1’ = Bit is set
‘0’ = Bit is cleared
x = Bit is unknown
bit 15
Unimplemented: Read as ‘0’
bit 14-12
T2IP<2:0>: Timer2 Interrupt Priority bits
111 = Interrupt is priority 7 (highest priority interrupt)
•
•
•
001 = Interrupt is priority 1
000 = Interrupt source is disabled
bit 11
Unimplemented: Read as ‘0’
bit 10-8
OC2IP<2:0>: Output Compare Channel 2 Interrupt Priority bits
111 = Interrupt is priority 7 (highest priority interrupt)
•
•
•
001 = Interrupt is priority 1
000 = Interrupt source is disabled
bit 7
Unimplemented: Read as ‘0’
bit 6-4
IC2IP<2:0>: Input Capture Channel 2 Interrupt Priority bits
111 = Interrupt is priority 7 (highest priority interrupt)
•
•
•
001 = Interrupt is priority 1
000 = Interrupt source is disabled
bit 3
Unimplemented: Read as ‘0’
bit 2-0
DMA0IP<2:0>: DMA Channel 0 Data Transfer Complete Interrupt Priority bits
111 = Interrupt is priority 7 (highest priority interrupt)
•
•
•
001 = Interrupt is priority 1
000 = Interrupt source is disabled
DS70592B-page 98
Preliminary
 2009 Microchip Technology Inc.
PIC24HJXXXGPX06A/X08A/X10A
REGISTER 7-17:
U-0
IPC2: INTERRUPT PRIORITY CONTROL REGISTER 2
R/W-1
—
R/W-0
R/W-0
U1RXIP<2:0>
U-0
R/W-1
—
R/W-0
R/W-0
SPI1IP<2:0>
bit 15
bit 8
U-0
R/W-1
—
R/W-0
SPI1EIP<2:0>
R/W-0
U-0
—
R/W-1
R/W-0
R/W-0
T3IP<2:0>
bit 7
bit 0
Legend:
R = Readable bit
W = Writable bit
U = Unimplemented bit, read as ‘0’
-n = Value at POR
‘1’ = Bit is set
‘0’ = Bit is cleared
bit 15
Unimplemented: Read as ‘0’
bit 14-12
U1RXIP<2:0>: UART1 Receiver Interrupt Priority bits
111 = Interrupt is priority 7 (highest priority interrupt)
•
•
•
001 = Interrupt is priority 1
000 = Interrupt source is disabled
bit 11
Unimplemented: Read as ‘0’
bit 10-8
SPI1IP<2:0>: SPI1 Event Interrupt Priority bits
111 = Interrupt is priority 7 (highest priority interrupt)
•
•
•
001 = Interrupt is priority 1
000 = Interrupt source is disabled
bit 7
Unimplemented: Read as ‘0’
bit 6-4
SPI1EIP<2:0>: SPI1 Error Interrupt Priority bits
111 = Interrupt is priority 7 (highest priority interrupt)
•
•
•
001 = Interrupt is priority 1
000 = Interrupt source is disabled
bit 3
Unimplemented: Read as ‘0’
bit 2-0
T3IP<2:0>: Timer3 Interrupt Priority bits
111 = Interrupt is priority 7 (highest priority interrupt)
•
•
•
001 = Interrupt is priority 1
000 = Interrupt source is disabled
 2009 Microchip Technology Inc.
Preliminary
x = Bit is unknown
DS70592B-page 99
PIC24HJXXXGPX06A/X08A/X10A
REGISTER 7-18:
IPC3: INTERRUPT PRIORITY CONTROL REGISTER 3
U-0
U-0
U-0
U-0
U-0
—
—
—
—
—
R/W-1
R/W-0
R/W-0
DMA1IP<2:0>
bit 15
bit 8
U-0
R/W-1
—
R/W-0
AD1IP<2:0>
R/W-0
U-0
R/W-1
—
R/W-0
R/W-0
U1TXIP<2:0>
bit 7
bit 0
Legend:
R = Readable bit
W = Writable bit
U = Unimplemented bit, read as ‘0’
-n = Value at POR
‘1’ = Bit is set
‘0’ = Bit is cleared
x = Bit is unknown
bit 15-11
Unimplemented: Read as ‘0’
bit 10-8
DMA1IP<2:0>: DMA Channel 1 Data Transfer Complete Interrupt Priority bits
111 = Interrupt is priority 7 (highest priority interrupt)
•
•
•
001 = Interrupt is priority 1
000 = Interrupt source is disabled
bit 7
Unimplemented: Read as ‘0’
bit 6-4
AD1IP<2:0>: ADC1 Conversion Complete Interrupt Priority bits
111 = Interrupt is priority 7 (highest priority interrupt)
•
•
•
001 = Interrupt is priority 1
000 = Interrupt source is disabled
bit 3
Unimplemented: Read as ‘0’
bit 2-0
U1TXIP<2:0>: UART1 Transmitter Interrupt Priority bits
111 = Interrupt is priority 7 (highest priority interrupt)
•
•
•
001 = Interrupt is priority 1
000 = Interrupt source is disabled
DS70592B-page 100
Preliminary
 2009 Microchip Technology Inc.
PIC24HJXXXGPX06A/X08A/X10A
REGISTER 7-19:
U-0
IPC4: INTERRUPT PRIORITY CONTROL REGISTER 4
R/W-1
R/W-0
—
R/W-0
CNIP<2:0>
U-0
U-0
U-0
U-0
—
—
—
—
bit 15
bit 8
U-0
R/W-1
—
R/W-0
MI2C1IP<2:0>
R/W-0
U-0
—
R/W-1
R/W-0
R/W-0
SI2C1IP<2:0>
bit 7
bit 0
Legend:
R = Readable bit
W = Writable bit
U = Unimplemented bit, read as ‘0’
-n = Value at POR
‘1’ = Bit is set
‘0’ = Bit is cleared
bit 15
Unimplemented: Read as ‘0’
bit 14-12
CNIP<2:0>: Change Notification Interrupt Priority bits
111 = Interrupt is priority 7 (highest priority interrupt)
•
•
•
001 = Interrupt is priority 1
000 = Interrupt source is disabled
bit 11-7
Unimplemented: Read as ‘0’
bit 6-4
MI2C1IP<2:0>: I2C1 Master Events Interrupt Priority bits
111 = Interrupt is priority 7 (highest priority interrupt)
•
•
•
001 = Interrupt is priority 1
000 = Interrupt source is disabled
bit 3
Unimplemented: Read as ‘0’
bit 2-0
SI2C1IP<2:0>: I2C1 Slave Events Interrupt Priority bits
111 = Interrupt is priority 7 (highest priority interrupt)
•
•
•
001 = Interrupt is priority 1
000 = Interrupt source is disabled
 2009 Microchip Technology Inc.
Preliminary
x = Bit is unknown
DS70592B-page 101
PIC24HJXXXGPX06A/X08A/X10A
REGISTER 7-20:
U-0
IPC5: INTERRUPT PRIORITY CONTROL REGISTER 5
R/W-1
—
R/W-0
R/W-0
IC8IP<2:0>
U-0
R/W-1
—
R/W-0
R/W-0
IC7IP<2:0>
bit 15
bit 8
U-0
R/W-1
—
R/W-0
AD2IP<2:0>
R/W-0
U-0
R/W-1
—
R/W-0
R/W-0
INT1IP<2:0>
bit 7
bit 0
Legend:
R = Readable bit
W = Writable bit
U = Unimplemented bit, read as ‘0’
-n = Value at POR
‘1’ = Bit is set
‘0’ = Bit is cleared
bit 15
Unimplemented: Read as ‘0’
bit 14-12
IC8IP<2:0>: Input Capture Channel 8 Interrupt Priority bits
111 = Interrupt is priority 7 (highest priority interrupt)
•
•
•
001 = Interrupt is priority 1
000 = Interrupt source is disabled
bit 11
Unimplemented: Read as ‘0’
bit 10-8
IC7IP<2:0>: Input Capture Channel 7 Interrupt Priority bits
111 = Interrupt is priority 7 (highest priority interrupt)
•
•
•
001 = Interrupt is priority 1
000 = Interrupt source is disabled
bit 7
Unimplemented: Read as ‘0’
bit 6-4
AD2IP<2:0>: ADC2 Conversion Complete Interrupt Priority bits
111 = Interrupt is priority 7 (highest priority interrupt)
•
•
•
001 = Interrupt is priority 1
000 = Interrupt source is disabled
bit 3
Unimplemented: Read as ‘0’
bit 2-0
INT1IP<2:0>: External Interrupt 1 Priority bits
111 = Interrupt is priority 7 (highest priority interrupt)
•
•
•
001 = Interrupt is priority 1
000 = Interrupt source is disabled
DS70592B-page 102
Preliminary
x = Bit is unknown
 2009 Microchip Technology Inc.
PIC24HJXXXGPX06A/X08A/X10A
REGISTER 7-21:
U-0
IPC6: INTERRUPT PRIORITY CONTROL REGISTER 6
R/W-1
—
R/W-0
R/W-0
T4IP<2:0>
U-0
R/W-1
—
R/W-0
R/W-0
OC4IP<2:0>
bit 15
bit 8
U-0
R/W-1
—
R/W-0
OC3IP<2:0>
R/W-0
U-0
R/W-1
—
R/W-0
R/W-0
DMA2IP<2:0>
bit 7
bit 0
Legend:
R = Readable bit
W = Writable bit
U = Unimplemented bit, read as ‘0’
-n = Value at POR
‘1’ = Bit is set
‘0’ = Bit is cleared
x = Bit is unknown
bit 15
Unimplemented: Read as ‘0’
bit 14-12
T4IP<2:0>: Timer4 Interrupt Priority bits
111 = Interrupt is priority 7 (highest priority interrupt)
•
•
•
001 = Interrupt is priority 1
000 = Interrupt source is disabled
bit 11
Unimplemented: Read as ‘0’
bit 10-8
OC4IP<2:0>: Output Compare Channel 4 Interrupt Priority bits
111 = Interrupt is priority 7 (highest priority interrupt)
•
•
•
001 = Interrupt is priority 1
000 = Interrupt source is disabled
bit 7
Unimplemented: Read as ‘0’
bit 6-4
OC3IP<2:0>: Output Compare Channel 3 Interrupt Priority bits
111 = Interrupt is priority 7 (highest priority interrupt)
•
•
•
001 = Interrupt is priority 1
000 = Interrupt source is disabled
bit 3
Unimplemented: Read as ‘0’
bit 2-0
DMA2IP<2:0>: DMA Channel 2 Data Transfer Complete Interrupt Priority bits
111 = Interrupt is priority 7 (highest priority interrupt)
•
•
•
001 = Interrupt is priority 1
000 = Interrupt source is disabled
 2009 Microchip Technology Inc.
Preliminary
DS70592B-page 103
PIC24HJXXXGPX06A/X08A/X10A
REGISTER 7-22:
U-0
IPC7: INTERRUPT PRIORITY CONTROL REGISTER 7
R/W-1
—
R/W-0
R/W-0
U2TXIP<2:0>
U-0
R/W-1
—
R/W-0
R/W-0
U2RXIP<2:0>
bit 15
bit 8
U-0
R/W-1
—
R/W-0
INT2IP<2:0>
R/W-0
U-0
—
R/W-1
R/W-0
R/W-0
T5IP<2:0>
bit 7
bit 0
Legend:
R = Readable bit
W = Writable bit
U = Unimplemented bit, read as ‘0’
-n = Value at POR
‘1’ = Bit is set
‘0’ = Bit is cleared
bit 15
Unimplemented: Read as ‘0’
bit 14-12
U2TXIP<2:0>: UART2 Transmitter Interrupt Priority bits
111 = Interrupt is priority 7 (highest priority interrupt)
•
•
•
001 = Interrupt is priority 1
000 = Interrupt source is disabled
bit 11
Unimplemented: Read as ‘0’
bit 10-8
U2RXIP<2:0>: UART2 Receiver Interrupt Priority bits
111 = Interrupt is priority 7 (highest priority interrupt)
•
•
•
001 = Interrupt is priority 1
000 = Interrupt source is disabled
bit 7
Unimplemented: Read as ‘0’
bit 6-4
INT2IP<2:0>: External Interrupt 2 Priority bits
111 = Interrupt is priority 7 (highest priority interrupt)
•
•
•
001 = Interrupt is priority 1
000 = Interrupt source is disabled
bit 3
Unimplemented: Read as ‘0’
bit 2-0
T5IP<2:0>: Timer5 Interrupt Priority bits
111 = Interrupt is priority 7 (highest priority interrupt)
•
•
•
001 = Interrupt is priority 1
000 = Interrupt source is disabled
DS70592B-page 104
Preliminary
x = Bit is unknown
 2009 Microchip Technology Inc.
PIC24HJXXXGPX06A/X08A/X10A
REGISTER 7-23:
U-0
IPC8: INTERRUPT PRIORITY CONTROL REGISTER 8
R/W-1
—
R/W-0
R/W-0
C1IP<2:0>
U-0
R/W-1
—
R/W-0
R/W-0
C1RXIP<2:0>
bit 15
bit 8
U-0
R/W-1
—
R/W-0
SPI2IP<2:0>
R/W-0
U-0
R/W-1
—
R/W-0
R/W-0
SPI2EIP<2:0>
bit 7
bit 0
Legend:
R = Readable bit
W = Writable bit
U = Unimplemented bit, read as ‘0’
-n = Value at POR
‘1’ = Bit is set
‘0’ = Bit is cleared
bit 15
Unimplemented: Read as ‘0’
bit 14-12
C1IP<2:0>: ECAN1 Event Interrupt Priority bits
111 = Interrupt is priority 7 (highest priority interrupt)
•
•
•
001 = Interrupt is priority 1
000 = Interrupt source is disabled
bit 11
Unimplemented: Read as ‘0’
bit 10-8
C1RXIP<2:0>: ECAN1 Receive Data Ready Interrupt Priority bits
111 = Interrupt is priority 7 (highest priority interrupt)
•
•
•
001 = Interrupt is priority 1
000 = Interrupt source is disabled
bit 7
Unimplemented: Read as ‘0’
bit 6-4
SPI2IP<2:0>: SPI2 Event Interrupt Priority bits
111 = Interrupt is priority 7 (highest priority interrupt)
•
•
•
001 = Interrupt is priority 1
000 = Interrupt source is disabled
bit 3
Unimplemented: Read as ‘0’
bit 2-0
SPI2EIP<2:0>: SPI2 Error Interrupt Priority bits
111 = Interrupt is priority 7 (highest priority interrupt)
•
•
•
001 = Interrupt is priority 1
000 = Interrupt source is disabled
 2009 Microchip Technology Inc.
Preliminary
x = Bit is unknown
DS70592B-page 105
PIC24HJXXXGPX06A/X08A/X10A
REGISTER 7-24:
U-0
IPC9: INTERRUPT PRIORITY CONTROL REGISTER 9
R/W-1
—
R/W-0
R/W-0
IC5IP<2:0>
U-0
R/W-1
—
R/W-0
R/W-0
IC4IP<2:0>
bit 15
bit 8
U-0
R/W-1
—
R/W-0
IC3IP<2:0>
R/W-0
U-0
—
R/W-1
R/W-0
R/W-0
DMA3IP<2:0>
bit 7
bit 0
Legend:
R = Readable bit
W = Writable bit
U = Unimplemented bit, read as ‘0’
-n = Value at POR
‘1’ = Bit is set
‘0’ = Bit is cleared
x = Bit is unknown
bit 15
Unimplemented: Read as ‘0’
bit 14-12
IC5IP<2:0>: Input Capture Channel 5 Interrupt Priority bits
111 = Interrupt is priority 7 (highest priority interrupt)
•
•
•
001 = Interrupt is priority 1
000 = Interrupt source is disabled
bit 11
Unimplemented: Read as ‘0’
bit 10-8
IC4IP<2:0>: Input Capture Channel 4 Interrupt Priority bits
111 = Interrupt is priority 7 (highest priority interrupt)
•
•
•
001 = Interrupt is priority 1
000 = Interrupt source is disabled
bit 7
Unimplemented: Read as ‘0’
bit 6-4
IC3IP<2:0>: Input Capture Channel 3 Interrupt Priority bits
111 = Interrupt is priority 7 (highest priority interrupt)
•
•
•
001 = Interrupt is priority 1
000 = Interrupt source is disabled
bit 3
Unimplemented: Read as ‘0’
bit 2-0
DMA3IP<2:0>: DMA Channel 3 Data Transfer Complete Interrupt Priority bits
111 = Interrupt is priority 7 (highest priority interrupt)
•
•
•
001 = Interrupt is priority 1
000 = Interrupt source is disabled
DS70592B-page 106
Preliminary
 2009 Microchip Technology Inc.
PIC24HJXXXGPX06A/X08A/X10A
REGISTER 7-25:
U-0
IPC10: INTERRUPT PRIORITY CONTROL REGISTER 10
R/W-1
—
R/W-0
R/W-0
OC7IP<2:0>
U-0
R/W-1
—
R/W-0
R/W-0
OC6IP<2:0>
bit 15
bit 8
U-0
R/W-1
—
R/W-0
OC5IP<2:0>
R/W-0
U-0
R/W-1
—
R/W-0
R/W-0
IC6IP<2:0>
bit 7
bit 0
Legend:
R = Readable bit
W = Writable bit
U = Unimplemented bit, read as ‘0’
-n = Value at POR
‘1’ = Bit is set
‘0’ = Bit is cleared
bit 15
Unimplemented: Read as ‘0’
bit 14-12
OC7IP<2:0>: Output Compare Channel 7 Interrupt Priority bits
111 = Interrupt is priority 7 (highest priority interrupt)
•
•
•
001 = Interrupt is priority 1
000 = Interrupt source is disabled
bit 11
Unimplemented: Read as ‘0’
bit 10-8
OC6IP<2:0>: Output Compare Channel 6 Interrupt Priority bits
111 = Interrupt is priority 7 (highest priority interrupt)
•
•
•
001 = Interrupt is priority 1
000 = Interrupt source is disabled
bit 7
Unimplemented: Read as ‘0’
bit 6-4
OC5IP<2:0>: Output Compare Channel 5 Interrupt Priority bits
111 = Interrupt is priority 7 (highest priority interrupt)
•
•
•
001 = Interrupt is priority 1
000 = Interrupt source is disabled
bit 3
Unimplemented: Read as ‘0’
bit 2-0
IC6IP<2:0>: Input Capture Channel 6 Interrupt Priority bits
111 = Interrupt is priority 7 (highest priority interrupt)
•
•
•
001 = Interrupt is priority 1
000 = Interrupt source is disabled
 2009 Microchip Technology Inc.
Preliminary
x = Bit is unknown
DS70592B-page 107
PIC24HJXXXGPX06A/X08A/X10A
REGISTER 7-26:
U-0
IPC11: INTERRUPT PRIORITY CONTROL REGISTER 11
R/W-1
—
R/W-0
R/W-0
T6IP<2:0>
U-0
R/W-1
—
R/W-0
R/W-0
DMA4IP<2:0>
bit 15
bit 8
U-0
U-0
U-0
U-0
U-0
—
—
—
—
—
R/W-1
R/W-0
R/W-0
OC8IP<2:0>
bit 7
bit 0
Legend:
R = Readable bit
W = Writable bit
U = Unimplemented bit, read as ‘0’
-n = Value at POR
‘1’ = Bit is set
‘0’ = Bit is cleared
x = Bit is unknown
bit 15
Unimplemented: Read as ‘0’
bit 14-12
T6IP<2:0>: Timer6 Interrupt Priority bits
111 = Interrupt is priority 7 (highest priority interrupt)
•
•
•
001 = Interrupt is priority 1
000 = Interrupt source is disabled
bit 11
Unimplemented: Read as ‘0’
bit 10-8
DMA4IP<2:0>: DMA Channel 4 Data Transfer Complete Interrupt Priority bits
111 = Interrupt is priority 7 (highest priority interrupt)
•
•
•
001 = Interrupt is priority 1
000 = Interrupt source is disabled
bit 7-3
Unimplemented: Read as ‘0’
bit 2-0
OC8IP<2:0>: Output Compare Channel 8 Interrupt Priority bits
111 = Interrupt is priority 7 (highest priority interrupt)
•
•
•
001 = Interrupt is priority 1
000 = Interrupt source is disabled
DS70592B-page 108
Preliminary
 2009 Microchip Technology Inc.
PIC24HJXXXGPX06A/X08A/X10A
REGISTER 7-27:
U-0
IPC12: INTERRUPT PRIORITY CONTROL REGISTER 12
R/W-1
R/W-0
—
R/W-0
T8IP<2:0>
U-0
R/W-1
—
R/W-0
R/W-0
MI2C2IP<2:0>
bit 15
bit 8
U-0
R/W-1
—
R/W-0
SI2C2IP<2:0>
R/W-0
U-0
—
R/W-1
R/W-0
R/W-0
T7IP<2:0>
bit 7
bit 0
Legend:
R = Readable bit
W = Writable bit
U = Unimplemented bit, read as ‘0’
-n = Value at POR
‘1’ = Bit is set
‘0’ = Bit is cleared
bit 15
Unimplemented: Read as ‘0’
bit 14-12
T8IP<2:0>: Timer8 Interrupt Priority bits
111 = Interrupt is priority 7 (highest priority interrupt)
•
•
•
001 = Interrupt is priority 1
000 = Interrupt source is disabled
bit 11
Unimplemented: Read as ‘0’
bit 10-8
MI2C2IP<2:0>: I2C2 Master Events Interrupt Priority bits
111 = Interrupt is priority 7 (highest priority interrupt)
•
•
•
001 = Interrupt is priority 1
000 = Interrupt source is disabled
bit 7
Unimplemented: Read as ‘0’
bit 6-4
SI2C2IP<2:0>: I2C2 Slave Events Interrupt Priority bits
111 = Interrupt is priority 7 (highest priority interrupt)
•
•
•
001 = Interrupt is priority 1
000 = Interrupt source is disabled
bit 3
Unimplemented: Read as ‘0’
bit 2-0
T7IP<2:0>: Timer7 Interrupt Priority bits
111 = Interrupt is priority 7 (highest priority interrupt)
•
•
•
001 = Interrupt is priority 1
000 = Interrupt source is disabled
 2009 Microchip Technology Inc.
Preliminary
x = Bit is unknown
DS70592B-page 109
PIC24HJXXXGPX06A/X08A/X10A
REGISTER 7-28:
U-0
IPC13: INTERRUPT PRIORITY CONTROL REGISTER 13
R/W-1
—
R/W-0
R/W-0
C2RXIP<2:0>
U-0
R/W-1
—
R/W-0
R/W-0
INT4IP<2:0>
bit 15
bit 8
U-0
R/W-1
—
R/W-0
INT3IP<2:0>
R/W-0
U-0
R/W-1
—
R/W-0
R/W-0
T9IP<2:0>
bit 7
bit 0
Legend:
R = Readable bit
W = Writable bit
U = Unimplemented bit, read as ‘0’
-n = Value at POR
‘1’ = Bit is set
‘0’ = Bit is cleared
bit 15
Unimplemented: Read as ‘0’
bit 14-12
C2RXIP<2:0>: ECAN2 Receive Data Ready Interrupt Priority bits
111 = Interrupt is priority 7 (highest priority interrupt)
•
•
•
001 = Interrupt is priority 1
000 = Interrupt source is disabled
bit 11
Unimplemented: Read as ‘0’
bit 10-8
INT4IP<2:0>: External Interrupt 4 Priority bits
111 = Interrupt is priority 7 (highest priority interrupt)
•
•
•
001 = Interrupt is priority 1
000 = Interrupt source is disabled
bit 7
Unimplemented: Read as ‘0’
bit 6-4
INT3IP<2:0>: External Interrupt 3 Priority bits
111 = Interrupt is priority 7 (highest priority interrupt)
•
•
•
001 = Interrupt is priority 1
000 = Interrupt source is disabled
bit 3
Unimplemented: Read as ‘0’
bit 2-0
T9IP<2:0>: Timer9 Interrupt Priority bits
111 = Interrupt is priority 7 (highest priority interrupt)
•
•
•
001 = Interrupt is priority 1
000 = Interrupt source is disabled
DS70592B-page 110
Preliminary
x = Bit is unknown
 2009 Microchip Technology Inc.
PIC24HJXXXGPX06A/X08A/X10A
REGISTER 7-29:
IPC14: INTERRUPT PRIORITY CONTROL REGISTER 14
U-0
U-0
U-0
U-0
U-0
U-0
U-0
U-0
—
—
—
—
—
—
—
—
bit 15
bit 8
U-0
U-0
U-0
U-0
U-0
—
—
—
—
—
R/W-1
R/W-0
R/W-0
C2IP<2:0>
bit 7
bit 0
Legend:
R = Readable bit
W = Writable bit
U = Unimplemented bit, read as ‘0’
-n = Value at POR
‘1’ = Bit is set
‘0’ = Bit is cleared
bit 15-3
Unimplemented: Read as ‘0’
bit 2-0
C2IP<2:0>: ECAN2 Event Interrupt Priority bits
111 = Interrupt is priority 7 (highest priority interrupt)
•
•
•
001 = Interrupt is priority 1
000 = Interrupt source is disabled
 2009 Microchip Technology Inc.
Preliminary
x = Bit is unknown
DS70592B-page 111
PIC24HJXXXGPX06A/X08A/X10A
REGISTER 7-30:
IPC15: INTERRUPT PRIORITY CONTROL REGISTER 15
U-0
U-0
U-0
U-0
U-0
U-0
U-0
U-0
—
—
—
—
—
—
—
—
bit 15
bit 8
U-0
R/W-1
—
R/W-0
DMA5IP<2:0>
R/W-0
U-0
U-0
U-0
U-0
—
—
—
—
bit 7
bit 0
Legend:
R = Readable bit
W = Writable bit
U = Unimplemented bit, read as ‘0’
-n = Value at POR
‘1’ = Bit is set
‘0’ = Bit is cleared
x = Bit is unknown
bit 15-7
Unimplemented: Read as ‘0’
bit 6-4
DMA5IP<2:0>: DMA Channel 5 Data Transfer Complete Interrupt Priority bits
111 = Interrupt is priority 7 (highest priority interrupt)
•
•
•
001 = Interrupt is priority 1
000 = Interrupt source is disabled
bit 3-0
Unimplemented: Read as ‘0’
DS70592B-page 112
Preliminary
 2009 Microchip Technology Inc.
PIC24HJXXXGPX06A/X08A/X10A
REGISTER 7-31:
IPC16: INTERRUPT PRIORITY CONTROL REGISTER 16
U-0
U-0
U-0
U-0
U-0
—
—
—
—
—
R/W-1
R/W-0
R/W-0
U2EIP<2:0>
bit 15
bit 8
U-0
R/W-1
—
R/W-0
U1EIP<2:0>
R/W-0
U-0
U-0
U-0
U-0
—
—
—
—
bit 7
bit 0
Legend:
R = Readable bit
W = Writable bit
U = Unimplemented bit, read as ‘0’
-n = Value at POR
‘1’ = Bit is set
‘0’ = Bit is cleared
bit 15-11
Unimplemented: Read as ‘0’
bit 10-8
U2EIP<2:0>: UART2 Error Interrupt Priority bits
111 = Interrupt is priority 7 (highest priority interrupt)
•
•
•
001 = Interrupt is priority 1
000 = Interrupt source is disabled
bit 7
Unimplemented: Read as ‘0’
bit 6-4
U1EIP<2:0>: UART1 Error Interrupt Priority bits
111 = Interrupt is priority 7 (highest priority interrupt)
•
•
•
001 = Interrupt is priority 1
000 = Interrupt source is disabled
bit 3-0
Unimplemented: Read as ‘0’
 2009 Microchip Technology Inc.
Preliminary
x = Bit is unknown
DS70592B-page 113
PIC24HJXXXGPX06A/X08A/X10A
REGISTER 7-32:
U-0
IPC17: INTERRUPT PRIORITY CONTROL REGISTER 17
R/W-1
—
R/W-0
R/W-0
C2TXIP<2:0>
U-0
R/W-1
—
R/W-0
R/W-0
C1TXIP<2:0>
bit 15
bit 8
U-0
R/W-1
—
R/W-0
DMA7IP<2:0>
R/W-0
U-0
R/W-1
—
R/W-0
R/W-0
DMA6IP<2:0>
bit 7
bit 0
Legend:
R = Readable bit
W = Writable bit
U = Unimplemented bit, read as ‘0’
-n = Value at POR
‘1’ = Bit is set
‘0’ = Bit is cleared
x = Bit is unknown
bit 15
Unimplemented: Read as ‘0’
bit 14-12
C2TXIP<2:0>: ECAN2 Transmit Data Request Interrupt Priority bits
111 = Interrupt is priority 7 (highest priority interrupt)
•
•
•
001 = Interrupt is priority 1
000 = Interrupt source is disabled
bit 11
Unimplemented: Read as ‘0’
bit 10-8
C1TXIP<2:0>: ECAN1 Transmit Data Request Interrupt Priority bits
111 = Interrupt is priority 7 (highest priority interrupt)
•
•
•
001 = Interrupt is priority 1
000 = Interrupt source is disabled
bit 7
Unimplemented: Read as ‘0’
bit 6-4
DMA7IP<2:0>: DMA Channel 7 Data Transfer Complete Interrupt Priority bits
111 = Interrupt is priority 7 (highest priority interrupt)
•
•
•
001 = Interrupt is priority 1
000 = Interrupt source is disabled
bit 3
Unimplemented: Read as ‘0’
bit 2-0
DMA6IP<2:0>: DMA Channel 6 Data Transfer Complete Interrupt Priority bits
111 = Interrupt is priority 7 (highest priority interrupt)
•
•
•
001 = Interrupt is priority 1
000 = Interrupt source is disabled
DS70592B-page 114
Preliminary
 2009 Microchip Technology Inc.
PIC24HJXXXGPX06A/X08A/X10A
REGISTER 7-33:
INTTREG: INTERRUPT CONTROL AND STATUS REGISTER
U-0
U-0
U-0
U-0
—
—
—
—
R-0
R-0
R-0
R-0
ILR<3:0>
bit 15
bit 8
U-0
U-0
R-0
—
R-0
R-0
R-0
R-0
R-0
VECNUM<6:0>
bit 7
bit 0
Legend:
R = Readable bit
W = Writable bit
U = Unimplemented bit, read as ‘0’
-n = Value at POR
‘1’ = Bit is set
‘0’ = Bit is cleared
bit 15-12
Unimplemented: Read as ‘0’
bit 11-8
ILR<3:0>: New CPU Interrupt Priority Level bits
1111 = CPU Interrupt Priority Level is 15
•
•
•
0001 = CPU Interrupt Priority Level is 1
0000 = CPU Interrupt Priority Level is 0
bit 7
Unimplemented: Read as ‘0’
bit 6-0
VECNUM<6:0>: Vector Number of Pending Interrupt bits
1111111 = Interrupt Vector pending is number 135
•
•
•
0000001 = Interrupt Vector pending is number 9
0000000 = Interrupt Vector pending is number 8
 2009 Microchip Technology Inc.
Preliminary
x = Bit is unknown
DS70592B-page 115
PIC24HJXXXGPX06A/X08A/X10A
7.4
7.4.3
Interrupt Setup Procedures
7.4.1
INITIALIZATION
To configure an interrupt source:
1.
2.
Set the NSTDIS bit (INTCON1<15>) if nested
interrupts are not desired.
Select the user-assigned priority level for the
interrupt source by writing the control bits in the
appropriate IPCx register. The priority level will
depend on the specific application and type of
interrupt source. If multiple priority levels are not
desired, the IPCx register control bits for all
enabled interrupt sources may be programmed
to the same non-zero value.
Note:
3.
4.
At a device Reset, the IPCx registers are
initialized, such that all user interrupt
sources are assigned to priority level 4.
Clear the interrupt flag status bit associated with
the peripheral in the associated IFSx register.
Enable the interrupt source by setting the interrupt enable control bit associated with the
source in the appropriate IECx register.
7.4.2
TRAP SERVICE ROUTINE
A Trap Service Routine (TSR) is coded like an ISR,
except that the appropriate trap status flag in the
INTCON1 register must be cleared to avoid re-entry
into the TSR.
7.4.4
INTERRUPT DISABLE
All user interrupts can be disabled using the following
procedure:
1.
2.
Push the current SR value onto the software
stack using the PUSH instruction.
Force the CPU to priority level 7 by inclusive
ORing the value 0x0E with SRL.
To enable user interrupts, the POP instruction may be
used to restore the previous SR value.
Note that only user interrupts with a priority level of 7 or
less can be disabled. Trap sources (level 8-level 15)
cannot be disabled.
The DISI instruction provides a convenient way to disable interrupts of priority levels 1-6 for a fixed period of
time. Level 7 interrupt sources are not disabled by the
DISI instruction.
INTERRUPT SERVICE ROUTINE
The method that is used to declare an ISR and initialize
the IVT with the correct vector address will depend on
the programming language (i.e., C or assembler) and
the language development toolsuite that is used to
develop the application. In general, the user must clear
the interrupt flag in the appropriate IFSx register for the
source of interrupt that the ISR handles. Otherwise, the
ISR will be re-entered immediately after exiting the
routine. If the ISR is coded in assembly language, it
must be terminated using a RETFIE instruction to
unstack the saved PC value, SRL value and old CPU
priority level.
DS70592B-page 116
Preliminary
 2009 Microchip Technology Inc.
PIC24HJXXXGPX06A/X08A/X10A
8.0
DIRECT MEMORY ACCESS
(DMA)
TABLE 8-1:
Note 1: This data sheet summarizes the features
of the PIC24HJXXXGPX06A/X08A/X10A
family of devices. However, it is not
intended to be a comprehensive reference source. To complement the information in this data sheet, refer to Section
22. “Direct Memory Access (DMA)”
(DS70223) of the “dsPIC33F/PIC24H
Family Reference Manual”, which is available from the Microchip website
(www.microchip.com).
2: Some registers and associated bits
described in this section may not be available on all devices. Refer to Section 4.0
“Memory Organization” in this data
sheet for device-specific register and bit
information.
Direct Memory Access (DMA) is a very efficient
mechanism of copying data between peripheral SFRs
(e.g., UART Receive register, Input Capture 1 buffer),
and buffers or variables stored in RAM, with minimal
CPU intervention. The DMA controller can
automatically copy entire blocks of data without
requiring the user software to read or write the
peripheral Special Function Registers (SFRs) every
time a peripheral interrupt occurs. The DMA controller
uses a dedicated bus for data transfers and, therefore,
does not steal cycles from the code execution flow of
the CPU. To exploit the DMA capability, the
corresponding user buffers or variables must be
located in DMA RAM.
The PIC24HJXXXGPX06A/X08A/X10A peripherals
that can utilize DMA are listed in Table 8-1 along with
their associated Interrupt Request (IRQ) numbers.
PERIPHERALS WITH DMA
SUPPORT
Peripheral
INT0
Input Capture 1
Input Capture 2
Output Compare 1
Output Compare 2
Timer2
Timer3
SPI1
SPI2
UART1 Reception
UART1 Transmission
UART2 Reception
UART2 Transmission
ADC1
ADC2
ECAN1 Reception
ECAN1 Transmission
ECAN2 Reception
ECAN2 Transmission
IRQ Number
0
1
5
2
6
7
8
10
33
11
12
30
31
13
21
34
70
55
71
The DMA controller features eight identical data
transfer channels.
Each channel has its own set of control and status
registers. Each DMA channel can be configured to
copy data either from buffers stored in dual port DMA
RAM to peripheral SFRs, or from peripheral SFRs to
buffers in DMA RAM.
The DMA controller supports the following features:
• Word or byte sized data transfers.
• Transfers from peripheral to DMA RAM or DMA
RAM to peripheral.
• Indirect Addressing of DMA RAM locations with or
without automatic post-increment.
• Peripheral Indirect Addressing – In some
peripherals, the DMA RAM read/write addresses
may be partially derived from the peripheral.
• One-Shot Block Transfers – Terminating DMA
transfer after one block transfer.
• Continuous Block Transfers – Reloading DMA RAM
buffer start address after every block transfer is
complete.
• Ping-Pong Mode – Switching between two DMA
RAM start addresses between successive block
transfers, thereby filling two buffers alternately.
• Automatic or manual initiation of block transfers
• Each channel can select from 19 possible sources
of data sources or destinations.
For each DMA channel, a DMA interrupt request is
generated when a block transfer is complete. Alternatively, an interrupt can be generated when half of the
block has been filled.
 2009 Microchip Technology Inc.
Preliminary
DS70592B-page 117
PIC24HJXXXGPX06A/X08A/X10A
FIGURE 8-1:
TOP LEVEL SYSTEM ARCHITECTURE USING A DEDICATED TRANSACTION BUS
Peripheral Indirect Address
DMA
Control
DMA Controller
DMA RAM
SRAM
PORT 1
SRAM X-Bus
DMA
Ready
Peripheral 3
DMA
Channels
PORT 2
CPU
DMA
DMA DS Bus
CPU Peripheral DS Bus
CPU
CPU
Non-DMA
Ready
Peripheral
DMA
DMA
Ready
Peripheral 1
CPU
DMA
DMA
Ready
Peripheral 2
Note: CPU and DMA address buses are not shown for clarity.
8.1
DMAC Registers
Each DMAC Channel x (x = 0, 1, 2, 3, 4, 5, 6 or 7)
contains the following registers:
• A 16-bit DMA Channel Control register
(DMAxCON)
• A 16-bit DMA Channel IRQ Select register
(DMAxREQ)
• A 16-bit DMA RAM Primary Start Address Offset
register (DMAxSTA)
• A 16-bit DMA RAM Secondary Start Address
Offset register (DMAxSTB)
• A 16-bit DMA Peripheral Address register
(DMAxPAD)
• A 10-bit DMA Transfer Count register (DMAxCNT)
An additional pair of status registers, DMACS0 and
DMACS1 are common to all DMAC channels.
DS70592B-page 118
Preliminary
 2009 Microchip Technology Inc.
PIC24HJXXXGPX06A/X08A/X10A
REGISTER 8-1:
DMAxCON: DMA CHANNEL x CONTROL REGISTER
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
U-0
U-0
U-0
CHEN
SIZE
DIR
HALF
NULLW
—
—
—
bit 15
bit 8
U-0
U-0
—
—
R/W-0
R/W-0
AMODE<1:0>
U-0
U-0
—
—
R/W-0
R/W-0
MODE<1:0>
bit 7
bit 0
Legend:
R = Readable bit
W = Writable bit
U = Unimplemented bit, read as ‘0’
-n = Value at POR
‘1’ = Bit is set
‘0’ = Bit is cleared
x = Bit is unknown
bit 15
CHEN: Channel Enable bit
1 = Channel enabled
0 = Channel disabled
bit 14
SIZE: Data Transfer Size bit
1 = Byte
0 = Word
bit 13
DIR: Transfer Direction bit (source/destination bus select)
1 = Read from DMA RAM address, write to peripheral address
0 = Read from peripheral address, write to DMA RAM address
bit 12
HALF: Early Block Transfer Complete Interrupt Select bit
1 = Initiate block transfer complete interrupt when half of the data has been moved
0 = Initiate block transfer complete interrupt when all of the data has been moved
bit 11
NULLW: Null Data Peripheral Write Mode Select bit
1 = Null data write to peripheral in addition to DMA RAM write (DIR bit must also be clear)
0 = Normal operation
bit 10-6
Unimplemented: Read as ‘0’
bit 5-4
AMODE<1:0>: DMA Channel Operating Mode Select bits
11 = Reserved
10 = Peripheral Indirect Addressing mode
01 = Register Indirect without Post-Increment mode
00 = Register Indirect with Post-Increment mode
bit 3-2
Unimplemented: Read as ‘0’
bit 1-0
MODE<1:0>: DMA Channel Operating Mode Select bits
11 = One-Shot, Ping-Pong modes enabled (one block transfer from/to each DMA RAM buffer)
10 = Continuous, Ping-Pong modes enabled
01 = One-Shot, Ping-Pong modes disabled
00 = Continuous, Ping-Pong modes disabled
 2009 Microchip Technology Inc.
Preliminary
DS70592B-page 119
PIC24HJXXXGPX06A/X08A/X10A
REGISTER 8-2:
DMAxREQ: DMA CHANNEL x IRQ SELECT REGISTER
R/W-0
U-0
U-0
U-0
U-0
U-0
U-0
U-0
FORCE(1)
—
—
—
—
—
—
—
bit 15
bit 8
U-0
R/W-0
R/W-0
—
IRQSEL6(2)
IRQSEL5(2)
R/W-0
R/W-0
IRQSEL4(2) IRQSEL3(2)
R/W-0
R/W-0
R/W-0
IRQSEL2(2)
IRQSEL1(2)
IRQSEL0(2)
bit 7
bit 0
Legend:
R = Readable bit
W = Writable bit
U = Unimplemented bit, read as ‘0’
-n = Value at POR
‘1’ = Bit is set
‘0’ = Bit is cleared
x = Bit is unknown
bit 15
FORCE: Force DMA Transfer bit(1)
1 = Force a single DMA transfer (Manual mode)
0 = Automatic DMA transfer initiation by DMA request
bit 14-7
Unimplemented: Read as ‘0’
bit 6-0
IRQSEL<6:0>: DMA Peripheral IRQ Number Select bits(2)
0000000-1111111 = DMAIRQ0-DMAIRQ127 selected to be Channel DMAREQ
Note 1: The FORCE bit cannot be cleared by the user. The FORCE bit is cleared by hardware when the forced
DMA transfer is complete.
2: Please see Table 8-1 for a complete listing of IRQ numbers for all interrupt sources.
DS70592B-page 120
Preliminary
 2009 Microchip Technology Inc.
PIC24HJXXXGPX06A/X08A/X10A
REGISTER 8-3:
R/W-0
DMAxSTA: DMA CHANNEL x RAM START ADDRESS OFFSET REGISTER A
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
STA<15:8>
bit 15
bit 8
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
STA<7:0>
bit 7
bit 0
Legend:
R = Readable bit
W = Writable bit
U = Unimplemented bit, read as ‘0’
-n = Value at POR
‘1’ = Bit is set
‘0’ = Bit is cleared
bit 15-0
x = Bit is unknown
STA<15:0>: Primary DMA RAM Start Address bits (source or destination)
REGISTER 8-4:
R/W-0
DMAxSTB: DMA CHANNEL x RAM START ADDRESS OFFSET REGISTER B
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
STB<15:8>
bit 15
bit 8
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
STB<7:0>
bit 7
bit 0
Legend:
R = Readable bit
W = Writable bit
U = Unimplemented bit, read as ‘0’
-n = Value at POR
‘1’ = Bit is set
‘0’ = Bit is cleared
bit 15-0
x = Bit is unknown
STB<15:0>: Secondary DMA RAM Start Address bits (source or destination)
 2009 Microchip Technology Inc.
Preliminary
DS70592B-page 121
PIC24HJXXXGPX06A/X08A/X10A
REGISTER 8-5:
R/W-0
DMAxPAD: DMA CHANNEL x PERIPHERAL ADDRESS REGISTER(1)
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
PAD<15:8>
bit 15
bit 8
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
PAD<7:0>
bit 7
bit 0
Legend:
R = Readable bit
W = Writable bit
U = Unimplemented bit, read as ‘0’
-n = Value at POR
‘1’ = Bit is set
‘0’ = Bit is cleared
bit 15-0
x = Bit is unknown
PAD<15:0>: Peripheral Address Register bits
Note 1: If the channel is enabled (i.e., active), writes to this register may result in unpredictable behavior of the
DMA channel and should be avoided.
REGISTER 8-6:
DMAxCNT: DMA CHANNEL x TRANSFER COUNT REGISTER(1)
U-0
U-0
U-0
U-0
U-0
U-0
—
—
—
—
—
—
R/W-0
R/W-0
CNT<9:8>(2)
bit 15
bit 8
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
CNT<7:0>(2)
bit 7
bit 0
Legend:
R = Readable bit
W = Writable bit
U = Unimplemented bit, read as ‘0’
-n = Value at POR
‘1’ = Bit is set
‘0’ = Bit is cleared
bit 15-10
Unimplemented: Read as ‘0’
bit 9-0
CNT<9:0>: DMA Transfer Count Register bits(2)
x = Bit is unknown
Note 1: If the channel is enabled (i.e., active), writes to this register may result in unpredictable behavior of the
DMA channel and should be avoided.
2: Number of DMA transfers = CNT<9:0> + 1.
DS70592B-page 122
Preliminary
 2009 Microchip Technology Inc.
PIC24HJXXXGPX06A/X08A/X10A
REGISTER 8-7:
DMACS0: DMA CONTROLLER STATUS REGISTER 0
R/C-0
R/C-0
R/C-0
R/C-0
R/C-0
R/C-0
R/C-0
R/C-0
PWCOL7
PWCOL6
PWCOL5
PWCOL4
PWCOL3
PWCOL2
PWCOL1
PWCOL0
bit 15
bit 8
R/C-0
R/C-0
R/C-0
R/C-0
R/C-0
R/C-0
R/C-0
R/C-0
XWCOL7
XWCOL6
XWCOL5
XWCOL4
XWCOL3
XWCOL2
XWCOL1
XWCOL0
bit 7
bit 0
Legend:
C = Clear only bit
R = Readable bit
W = Writable bit
U = Unimplemented bit, read as ‘0’
-n = Value at POR
‘1’ = Bit is set
‘0’ = Bit is cleared
bit 15
PWCOL7: Channel 7 Peripheral Write Collision Flag bit
1 = Write collision detected
0 = No write collision detected
bit 14
PWCOL6: Channel 6 Peripheral Write Collision Flag bit
1 = Write collision detected
0 = No write collision detected
bit 13
PWCOL5: Channel 5 Peripheral Write Collision Flag bit
1 = Write collision detected
0 = No write collision detected
bit 12
PWCOL4: Channel 4 Peripheral Write Collision Flag bit
1 = Write collision detected
0 = No write collision detected
bit 11
PWCOL3: Channel 3 Peripheral Write Collision Flag bit
1 = Write collision detected
0 = No write collision detected
bit 10
PWCOL2: Channel 2 Peripheral Write Collision Flag bit
1 = Write collision detected
0 = No write collision detected
bit 9
PWCOL1: Channel 1 Peripheral Write Collision Flag bit
1 = Write collision detected
0 = No write collision detected
bit 8
PWCOL0: Channel 0 Peripheral Write Collision Flag bit
1 = Write collision detected
0 = No write collision detected
bit 7
XWCOL7: Channel 7 DMA RAM Write Collision Flag bit
1 = Write collision detected
0 = No write collision detected
bit 6
XWCOL6: Channel 6 DMA RAM Write Collision Flag bit
1 = Write collision detected
0 = No write collision detected
bit 5
XWCOL5: Channel 5 DMA RAM Write Collision Flag bit
1 = Write collision detected
0 = No write collision detected
bit 4
XWCOL4: Channel 4 DMA RAM Write Collision Flag bit
1 = Write collision detected
0 = No write collision detected
 2009 Microchip Technology Inc.
Preliminary
x = Bit is unknown
DS70592B-page 123
PIC24HJXXXGPX06A/X08A/X10A
REGISTER 8-7:
DMACS0: DMA CONTROLLER STATUS REGISTER 0 (CONTINUED)
bit 3
XWCOL3: Channel 3 DMA RAM Write Collision Flag bit
1 = Write collision detected
0 = No write collision detected
bit 2
XWCOL2: Channel 2 DMA RAM Write Collision Flag bit
1 = Write collision detected
0 = No write collision detected
bit 1
XWCOL1: Channel 1 DMA RAM Write Collision Flag bit
1 = Write collision detected
0 = No write collision detected
bit 0
XWCOL0: Channel 0 DMA RAM Write Collision Flag bit
1 = Write collision detected
0 = No write collision detected
DS70592B-page 124
Preliminary
 2009 Microchip Technology Inc.
PIC24HJXXXGPX06A/X08A/X10A
REGISTER 8-8:
DMACS1: DMA CONTROLLER STATUS REGISTER 1
U-0
U-0
U-0
U-0
—
—
—
—
R-1
R-1
R-1
R-1
LSTCH<3:0>
bit 15
bit 8
R-0
R-0
R-0
R-0
R-0
R-0
R-0
R-0
PPST7
PPST6
PPST5
PPST4
PPST3
PPST2
PPST1
PPST0
bit 7
bit 0
Legend:
R = Readable bit
W = Writable bit
U = Unimplemented bit, read as ‘0’
-n = Value at POR
‘1’ = Bit is set
‘0’ = Bit is cleared
bit 15-12
Unimplemented: Read as ‘0’
bit 11-8
LSTCH<3:0>: Last DMA Channel Active bits
1111 = No DMA transfer has occurred since system Reset
1110-1000 = Reserved
0111 = Last data transfer was by DMA Channel 7
0110 = Last data transfer was by DMA Channel 6
0101 = Last data transfer was by DMA Channel 5
0100 = Last data transfer was by DMA Channel 4
0011 = Last data transfer was by DMA Channel 3
0010 = Last data transfer was by DMA Channel 2
0001 = Last data transfer was by DMA Channel 1
0000 = Last data transfer was by DMA Channel 0
bit 7
PPST7: Channel 7 Ping-Pong Mode Status Flag bit
1 = DMA7STB register selected
0 = DMA7STA register selected
bit 6
PPST6: Channel 6 Ping-Pong Mode Status Flag bit
1 = DMA6STB register selected
0 = DMA6STA register selected
bit 5
PPST5: Channel 5 Ping-Pong Mode Status Flag bit
1 = DMA5STB register selected
0 = DMA5STA register selected
bit 4
PPST4: Channel 4 Ping-Pong Mode Status Flag bit
1 = DMA4STB register selected
0 = DMA4STA register selected
bit 3
PPST3: Channel 3 Ping-Pong Mode Status Flag bit
1 = DMA3STB register selected
0 = DMA3STA register selected
bit 2
PPST2: Channel 2 Ping-Pong Mode Status Flag bit
1 = DMA2STB register selected
0 = DMA2STA register selected
bit 1
PPST1: Channel 1 Ping-Pong Mode Status Flag bit
1 = DMA1STB register selected
0 = DMA1STA register selected
bit 0
PPST0: Channel 0 Ping-Pong Mode Status Flag bit
1 = DMA0STB register selected
0 = DMA0STA register selected
 2009 Microchip Technology Inc.
Preliminary
x = Bit is unknown
DS70592B-page 125
PIC24HJXXXGPX06A/X08A/X10A
REGISTER 8-9:
R-0
DSADR: MOST RECENT DMA RAM ADDRESS
R-0
R-0
R-0
R-0
R-0
R-0
R-0
DSADR<15:8>
bit 15
bit 8
R-0
R-0
R-0
R-0
R-0
R-0
R-0
R-0
DSADR<7:0>
bit 7
bit 0
Legend:
R = Readable bit
W = Writable bit
U = Unimplemented bit, read as ‘0’
-n = Value at POR
‘1’ = Bit is set
‘0’ = Bit is cleared
bit 15-0
x = Bit is unknown
DSADR<15:0>: Most Recent DMA RAM Address Accessed by DMA Controller bits
DS70592B-page 126
Preliminary
 2009 Microchip Technology Inc.
PIC24HJXXXGPX06A/X08A/X10A
9.0
OSCILLATOR
CONFIGURATION
The
PIC24HJXXXGPX06A/X08A/X10A
system provides:
Note 1: This data sheet summarizes the features
of the PIC24HJXXXGPX06A/X08A/X10A
family of devices. However, it is not
intended to be a comprehensive
reference source. To complement the
information in this data sheet, refer to
Section 7. “Oscillator” (DS70227) of
the “dsPIC33F/dsPIC33F/PIC24H Family
Reference Manual”, which is available
from
the
Microchip
website
(www.microchip.com).
2: Some registers and associated bits
described in this section may not be available on all devices. Refer to Section 4.0
“Memory Organization” in this data
sheet for device-specific register and bit
information.
FIGURE 9-1:
oscillator
• Various external and internal oscillator options as
clock sources
• An on-chip PLL to scale the internal operating
frequency to the required system clock frequency
• The internal FRC oscillator can also be used with
the PLL, thereby allowing full-speed operation
without any external clock generation hardware
• Clock switching between various clock sources
• Programmable clock postscaler for system power
savings
• A Fail-Safe Clock Monitor (FSCM) that detects
clock failure and takes fail-safe measures
• A Clock Control register (OSCCON)
• Nonvolatile Configuration bits for main oscillator
selection.
A simplified diagram of the oscillator system is shown
in Figure 9-1.
PIC24HJXXXGPX06A/X08A/X10A OSCILLATOR SYSTEM DIAGRAM
Primary Oscillator
XT, HS, EC
R(2)
S3
S1
OSC2
PLL(1)
DOZE<2:0>
S2
XTPLL, HSPLL,
ECPLL, FRCPLL
DOZE
OSC1
S1/S3
POSCMD<1:0>
FCY
FRCDIV
FP
FRC
Oscillator
FRCDIVN
S7
÷ 2
FOSC
FRCDIV<2:0>
TUN<5:0>
FRCDIV16
S6
FRC
S0
÷ 16
LPRC
LPRC
Oscillator
Secondary Oscillator
SOSC
SOSCO
S5
S4
LPOSCEN
SOSCI
Clock Fail
S7
Clock Switch
Reset
NOSC<2:0> FNOSC<2:0>
WDT, PWRT,
FSCM
Timer 1
Note 1:
2:
See Figure 9-2 for PLL details.
If the Oscillator is used with XT or HS modes, an extended parallel resistor with the value of 1 M must be connected.
 2009 Microchip Technology Inc.
Preliminary
DS70592B-page 127
PIC24HJXXXGPX06A/X08A/X10A
9.1
CPU Clocking System
There are seven system clock options provided by the
PIC24HJXXXGPX06A/X08A/X10A:
•
•
•
•
•
•
•
FRC Oscillator
FRC Oscillator with PLL
Primary (XT, HS or EC) Oscillator
Primary Oscillator with PLL
Secondary (LP) Oscillator
LPRC Oscillator
FRC Oscillator with postscaler
9.1.1
SYSTEM CLOCK SOURCES
The primary oscillator can use one of the following as
its clock source:
2.
3.
XT (Crystal): Crystals and ceramic resonators in
the range of 3 MHz to 10 MHz. The crystal is
connected to the OSC1 and OSC2 pins.
HS (High-Speed Crystal): Crystals in the range
of 10 MHz to 40 MHz. The crystal is connected
to the OSC1 and OSC2 pins.
EC (External Clock): External clock signal is
directly applied to the OSC1 pin.
The secondary (LP) oscillator is designed for low power
and uses a 32.768 kHz crystal or ceramic resonator.
The LP oscillator uses the SOSCI and SOSCO pins.
The LPRC (Low-Power RC) internal oscIllator runs at a
nominal frequency of 32.768 kHz. It is also used as a
reference clock by the Watchdog Timer (WDT) and
Fail-Safe Clock Monitor (FSCM).
The clock signals generated by the FRC and primary
oscillators can be optionally applied to an on-chip
Phase Locked Loop (PLL) to provide a wide range of
output frequencies for device operation. PLL
configuration is described in Section 9.1.3 “PLL
Configuration”.
The FRC frequency depends on the FRC accuracy
(see Table 24-19) and the value of the FRC Oscillator
Tuning register (see Register 9-4).
9.1.2
SYSTEM CLOCK SELECTION
The oscillator source that is used at a device Power-on
Reset event is selected using Configuration bit settings.
The oscillator Configuration bit settings are located in the
Configuration registers in the program memory. (Refer to
Section 21.1 “Configuration Bits” for further details.)
The Initial Oscillator Selection Configuration bits,
FNOSC<2:0> (FOSCSEL<2:0>), and the Primary Oscillator Mode Select Configuration bits, POSCMD<1:0>
DS70592B-page 128
The Configuration bits allow users to choose between
twelve different clock modes, shown in Table 9-1.
The output of the oscillator (or the output of the PLL if
a PLL mode has been selected) FOSC is divided by 2 to
generate the device instruction clock (FCY) and the
peripheral clock time base (FP). FCY defines the
operating speed of the device, and speeds up to 40
MHz are supported by the PIC24HJXXXGPX06A/
X08A/X10A architecture.
The FRC (Fast RC) internal oscillator runs at a nominal
frequency of 7.37 MHz. The user software can tune the
FRC frequency. User software can optionally specify a
factor (ranging from 1:2 to 1:256) by which the FRC
clock frequency is divided. This factor is selected using
the FRCDIV<2:0> (CLKDIV<10:8>) bits.
1.
(FOSC<1:0>), select the oscillator source that is used at
a Power-on Reset. The FRC primary oscillator is the
default (unprogrammed) selection.
Instruction execution speed or device operating
frequency, FCY, is given by:
EQUATION 9-1:
DEVICE OPERATING
FREQUENCY
F OSC
F CY = ------------2
9.1.3
PLL CONFIGURATION
The primary oscillator and internal FRC oscillator can
optionally use an on-chip PLL to obtain higher speeds
of operation. The PLL provides a significant amount of
flexibility in selecting the device operating speed. A
block diagram of the PLL is shown in Figure 9-2.
The output of the primary oscillator or FRC, denoted as
‘FIN’, is divided down by a prescale factor (N1) of 2, 3,
... or 33 before being provided to the PLL’s Voltage
Controlled Oscillator (VCO). The input to the VCO must
be selected to be in the range of 0.8 MHz to 8 MHz.
Since the minimum prescale factor is 2, this implies that
FIN must be chosen to be in the range of 1.6 MHz to 16
MHz. The prescale factor ‘N1’ is selected using the
PLLPRE<4:0> bits (CLKDIV<4:0>).
The PLL Feedback Divisor, selected using the
PLLDIV<8:0> bits (PLLFBD<8:0>), provides a factor ‘M’,
by which the input to the VCO is multiplied. This factor
must be selected such that the resulting VCO output
frequency is in the range of 100 MHz to 200 MHz.
The VCO output is further divided by a postscale factor
‘N2’. This factor is selected using the PLLPOST<1:0>
bits (CLKDIV<7:6>). ‘N2’ can be either 2, 4 or 8, and
must be selected such that the PLL output frequency
(FOSC) is in the range of 12.5 MHz to 80 MHz, which
generates device operating speeds of 6.25-40 MIPS.
For a primary oscillator or FRC oscillator, output ‘FIN’,
the PLL output ‘FOSC’ is given by:
EQUATION 9-2:
Preliminary
FOSC CALCULATION
M
F OSC = F IN   -------------------
N1  N2
 2009 Microchip Technology Inc.
PIC24HJXXXGPX06A/X08A/X10A
EQUATION 9-3:
For example, suppose a 10 MHz crystal is being used,
with “XT with PLL” being the selected oscillator mode.
If PLLPRE<4:0> = 0, then N1 = 2. This yields a VCO
input of 10/2 = 5 MHz, which is within the acceptable
range of 0.8-8 MHz. If PLLDIV<8:0> = 0x1E, then
M = 32. This yields a VCO output of 5 x 32 = 160 MHz,
which is within the 100-200 MHz ranged needed.
XT WITH PLL MODE
EXAMPLE
1 10000000  32
F OSC
F CY = ------------- = ---  ---------------------------------- = 40 MIPS

2
22
2
If PLLPOST<1:0> = 0, then N2 = 2. This provides a
Fosc of 160/2 = 80 MHz. The resultant device operating
speed is 80/2 = 40 MIPS.
FIGURE 9-2:
PIC24HJXXXGPX06A/X08A/X10A PLL BLOCK DIAGRAM
FVCO
100-200 MHz
Here(1)
0.8-8.0 MHz
Here(1)
Source (Crystal, External Clock
or Internal RC)
PLLPRE
VCO
X
12.5-80 MHz
Here(1)
FOSC
PLLPOST
PLLDIV
N1
Divide by
2-33
M
Divide by
2-513
N2
Divide by
2, 4, 8
Note 1: This frequency range must be satisfied at all times.
TABLE 9-1:
CONFIGURATION BIT VALUES FOR CLOCK SELECTION
Oscillator Mode
Oscillator Source
POSCMD<1:0>
FNOSC<2:0>
Note
Fast RC Oscillator with Divide-by-N
(FRCDIVN)
Internal
xx
111
1, 2
Fast RC Oscillator with Divide-by-16
(FRCDIV16)
Internal
xx
110
1
Low-Power RC Oscillator (LPRC)
Internal
xx
101
1
Secondary
xx
100
1
Primary Oscillator (HS) with PLL
(HSPLL)
Primary
10
011
—
Primary Oscillator (XT) with PLL
(XTPLL)
Primary
01
011
—
Primary Oscillator (EC) with PLL
(ECPLL)
Primary
00
011
1
Primary Oscillator (HS)
Primary
10
010
—
Primary Oscillator (XT)
Primary
01
010
—
Primary Oscillator (EC)
Primary
00
010
1
Fast RC Oscillator with PLL (FRCPLL)
Internal
xx
001
1
Fast RC Oscillator (FRC)
Internal
xx
000
1
Secondary (Timer1) Oscillator (SOSC)
Note 1:
2:
OSC2 pin function is determined by the OSCIOFNC Configuration bit.
This is the default oscillator mode for an unprogrammed (erased) device.
 2009 Microchip Technology Inc.
Preliminary
DS70592B-page 129
PIC24HJXXXGPX06A/X08A/X10A
REGISTER 9-1:
U-0
OSCCON: OSCILLATOR CONTROL REGISTER(1)
R-0
—
R-0
R-0
COSC<2:0>
U-0
R/W-y
R/W-y
R/W-y
NOSC<2:0>(2)
—
bit 15
bit 8
R/W-0
CLKLOCK
U-0
—
R-0
LOCK
U-0
—
R/C-0
CF
U-0
—
R/W-0
LPOSCEN
R/W-0
OSWEN
bit 7
bit 0
Legend:
y = Value set from Configuration bits on POR
R = Readable bit
-n = Value at POR
W = Writable bit
‘1’ = Bit is set
C = Clear only bit
U = Unimplemented bit, read as ‘0’
‘0’ = Bit is cleared
x = Bit is unknown
bit 15
bit 14-12
Unimplemented: Read as ‘0’
COSC<2:0>: Current Oscillator Selection bits (read-only)
000 = Fast RC oscillator (FRC)
001 = Fast RC oscillator (FRC) with PLL
010 = Primary oscillator (XT, HS, EC)
011 = Primary oscillator (XT, HS, EC) with PLL
100 = Secondary oscillator (SOSC)
101 = Low-Power RC oscillator (LPRC)
110 = Fast RC oscillator (FRC) with Divide-by-16
111 = Fast RC oscillator (FRC) with Divide-by-n
bit 11
bit 10-8
Unimplemented: Read as ‘0’
NOSC<2:0>: New Oscillator Selection bits(2)
000 = Fast RC oscillator (FRC)
001 = Fast RC oscillator (FRC) with PLL
010 = Primary oscillator (XT, HS, EC)
011 = Primary oscillator (XT, HS, EC) with PLL
100 = Secondary oscillator (SOSC)
101 = Low-Power RC oscillator (LPRC)
110 = Fast RC oscillator (FRC) with Divide-by-16
111 = Fast RC oscillator (FRC) with Divide-by-n
bit 7
CLKLOCK: Clock Lock Enable bit
1 = If (FCKSM0 = 1), then clock and PLL configurations are locked
If (FCKSM0 = 0), then clock and PLL configurations may be modified
0 = Clock and PLL selections are not locked, configurations may be modified
bit 6
bit 5
Unimplemented: Read as ‘0’
LOCK: PLL Lock Status bit (read-only)
1 = Indicates that PLL is in lock, or PLL start-up timer is satisfied
0 = Indicates that PLL is out of lock, start-up timer is in progress or PLL is disabled
bit 4
bit 3
Unimplemented: Read as ‘0’
CF: Clock Fail Detect bit (read/clear by application)
1 = FSCM has detected clock failure
0 = FSCM has not detected clock failure
bit 2
Unimplemented: Read as ‘0’
Note 1: Writes to this register require an unlock sequence. Refer to Section 7. “Oscillator” (DS70227) in the
“dsPIC33F/PIC24H Family Reference Manual” (available from the Microchip website) for details.
2: Direct clock switches between any primary oscillator mode with PLL and FRCPLL mode are not permitted.
This applies to clock switches in either direction. In these instances, the application must switch to FRC mode
as a transition clock source between the two PLL modes.
DS70592B-page 130
Preliminary
 2009 Microchip Technology Inc.
PIC24HJXXXGPX06A/X08A/X10A
REGISTER 9-1:
OSCCON: OSCILLATOR CONTROL REGISTER(1) (CONTINUED)
bit 1
LPOSCEN: Secondary (LP) Oscillator Enable bit
1 = Enable secondary oscillator
0 = Disable secondary oscillator
bit 0
OSWEN: Oscillator Switch Enable bit
1 = Request oscillator switch to selection specified by NOSC<2:0> bits
0 = Oscillator switch is complete
Note 1: Writes to this register require an unlock sequence. Refer to Section 7. “Oscillator” (DS70227) in the
“dsPIC33F/PIC24H Family Reference Manual” (available from the Microchip website) for details.
2: Direct clock switches between any primary oscillator mode with PLL and FRCPLL mode are not permitted.
This applies to clock switches in either direction. In these instances, the application must switch to FRC mode
as a transition clock source between the two PLL modes.
 2009 Microchip Technology Inc.
Preliminary
DS70592B-page 131
PIC24HJXXXGPX06A/X08A/X10A
REGISTER 9-2:
R/W-0
CLKDIV: CLOCK DIVISOR REGISTER
R/W-0
ROI
R/W-1
R/W-1
R/W-0
R/W-0
DOZEN(1)
DOZE<2:0>
R/W-0
R/W-0
FRCDIV<2:0>
bit 15
bit 8
R/W-0
R/W-1
PLLPOST<1:0>
U-0
R/W-0
R/W-0
—
R/W-0
R/W-0
R/W-0
PLLPRE<4:0>
bit 7
bit 0
Legend:
y = Value set from Configuration bits on POR
R = Readable bit
W = Writable bit
U = Unimplemented bit, read as ‘0’
-n = Value at POR
‘1’ = Bit is set
‘0’ = Bit is cleared
x = Bit is unknown
bit 15
ROI: Recover on Interrupt bit
1 = Interrupts will clear the DOZEN bit and the processor clock/peripheral clock ratio is set to 1:1
0 = Interrupts have no effect on the DOZEN bit
bit 14-12
DOZE<2:0>: Processor Clock Reduction Select bits
000 = FCY/1
001 = FCY/2
010 = FCY/4
011 = FCY/8 (default)
100 = FCY/16
101 = FCY/32
110 = FCY/64
111 = FCY/128
bit 11
DOZEN: DOZE Mode Enable bit(1)
1 = DOZE<2:0> field specifies the ratio between the peripheral clocks and the processor clocks
0 = Processor clock/peripheral clock ratio forced to 1:1
bit 10-8
FRCDIV<2:0>: Internal Fast RC Oscillator Postscaler bits
000 = FRC divide by 1 (default)
001 = FRC divide by 2
010 = FRC divide by 4
011 = FRC divide by 8
100 = FRC divide by 16
101 = FRC divide by 32
110 = FRC divide by 64
111 = FRC divide by 256
bit 7-6
PLLPOST<1:0>: PLL VCO Output Divider Select bits (also denoted as ‘N2’, PLL postscaler)
00 = Output/2
01 = Output/4 (default)
10 = Reserved
11 = Output/8
bit 5
Unimplemented: Read as ‘0’
bit 4-0
PLLPRE<4:0>: PLL Phase Detector Input Divider bits (also denoted as ‘N1’, PLL prescaler)
00000 = Input/2 (default)
00001 = Input/3
•
•
•
11111 = Input/33
Note 1: This bit is cleared when the ROI bit is set and an interrupt occurs.
DS70592B-page 132
Preliminary
 2009 Microchip Technology Inc.
PIC24HJXXXGPX06A/X08A/X10A
REGISTER 9-3:
PLLFBD: PLL FEEDBACK DIVISOR REGISTER
U-0
U-0
U-0
U-0
U-0
U-0
U-0
R/W-0
—
—
—
—
—
—
—
PLLDIV<8>
bit 15
bit 8
R/W-0
R/W-0
R/W-1
R/W-1
R/W-0
R/W-0
R/W-0
R/W-0
PLLDIV<7:0>
bit 7
bit 0
Legend:
R = Readable bit
W = Writable bit
U = Unimplemented bit, read as ‘0’
-n = Value at POR
‘1’ = Bit is set
‘0’ = Bit is cleared
x = Bit is unknown
bit 15-9
Unimplemented: Read as ‘0’
bit 8-0
PLLDIV<8:0>: PLL Feedback Divisor bits (also denoted as ‘M’, PLL multiplier)
000000000 = 2
000000001 = 3
000000010 = 4
•
•
•
000110000 = 50 (default)
•
•
•
111111111 = 513
 2009 Microchip Technology Inc.
Preliminary
DS70592B-page 133
PIC24HJXXXGPX06A/X08A/X10A
REGISTER 9-4:
OSCTUN: FRC OSCILLATOR TUNING REGISTER
U-0
U-0
U-0
U-0
U-0
U-0
U-0
U-0
—
—
—
—
—
—
—
—
bit 15
bit 8
U-0
U-0
—
—
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
TUN<5:0>(1)
bit 7
bit 0
Legend:
R = Readable bit
W = Writable bit
U = Unimplemented bit, read as ‘0’
-n = Value at POR
‘1’ = Bit is set
‘0’ = Bit is cleared
bit 15-6
Unimplemented: Read as ‘0’
bit 5-0
TUN<5:0>: FRC Oscillator Tuning bits(1)
011111 = Center frequency + 11.625% (8.23 MHz)
011110 = Center frequency + 11.25% (8.20 MHz)
•
•
•
000001 = Center frequency + 0.375% (7.40 MHz)
000000 = Center frequency (7.37 MHz nominal)
111111 = Center frequency – 0.375% (7.345 MHz)
•
•
•
100001 = Center frequency – 11.625% (6.52 MHz)
100000 = Center frequency – 12% (6.49 MHz)
x = Bit is unknown
Note 1: OSCTUN functionality has been provided to help customers compensate for temperature effects on the
FRC frequency over a wide range of temperatures. The tuning step size is an approximation and is neither
characterized nor tested.
DS70592B-page 134
Preliminary
 2009 Microchip Technology Inc.
PIC24HJXXXGPX06A/X08A/X10A
9.2
Clock Switching Operation
2.
Applications are free to switch between any of the four
clock sources (Primary, LP, FRC and LPRC) under
software control at any time. To limit the possible side
effects that could result from this flexibility,
PIC24HJXXXGPX06A/X08A/X10A devices have a
safeguard lock built into the switch process.
Note:
Primary Oscillator mode has three different
submodes (XT, HS and EC) which are
determined by the POSCMD<1:0> Configuration bits. While an application can
switch to and from Primary Oscillator
mode in software, it cannot switch
between the different primary submodes
without reprogramming the device.
If a valid clock switch has been initiated, the
LOCK
(OSCCON<5>)
and
the
CF
(OSCCON<3>) status bits are cleared.
The new oscillator is turned on by the hardware
if it is not currently running. If a crystal oscillator
must be turned on, the hardware waits until the
Oscillator Start-up Timer (OST) expires. If the
new source is using the PLL, the hardware waits
until a PLL lock is detected (LOCK = 1).
The hardware waits for 10 clock cycles from the
new clock source and then performs the clock
switch.
The hardware clears the OSWEN bit to indicate a
successful clock transition. In addition, the NOSC
bit values are transferred to the COSC status bits.
The old clock source is turned off at this time,
with the exception of LPRC (if WDT or FSCM
are enabled) or LP (if LPOSCEN remains set).
3.
4.
5.
6.
9.2.1
ENABLING CLOCK SWITCHING
To enable clock switching, the FCKSM1 Configuration
bit in the Configuration register must be programmed to
‘0’. (Refer to Section 21.1 “Configuration Bits” for
further details.) If the FCKSM1 Configuration bit is
unprogrammed (‘1’), the clock switching function and
Fail-Safe Clock Monitor function are disabled. This is
the default setting.
Note 1: The processor continues to execute code
throughout the clock switching sequence.
Timing sensitive code should not be
executed during this time.
2: Direct clock switches between any primary
oscillator mode with PLL and FRCPLL
mode are not permitted. This applies to
clock switches in either direction. In these
instances, the application must switch to
FRC mode as a transition clock source
between the two PLL modes.
3: Refer to Section 7. “Oscillator”
(DS70227) in the “dsPIC33F/PIC24H
Family Reference Manual” for details.
The NOSC control bits (OSCCON<10:8>) do not
control the clock selection when clock switching is
disabled. However, the COSC bits (OSCCON<14:12>)
reflect the clock source selected by the FNOSC
Configuration bits.
The OSWEN control bit (OSCCON<0>) has no effect
when clock switching is disabled. It is held at ‘0’ at all
times.
9.2.2
OSCILLATOR SWITCHING SEQUENCE
At a minimum, performing a clock switch requires this
basic sequence:
1.
2.
3.
4.
5.
If
desired,
read
the
COSC
bits
(OSCCON<14:12>) to determine the current
oscillator source.
Perform the unlock sequence to allow a write to
the OSCCON register high byte.
Write the appropriate value to the NOSC control
bits (OSCCON<10:8>) for the new oscillator
source.
Perform the unlock sequence to allow a write to
the OSCCON register low byte.
Set the OSWEN bit to initiate the oscillator
switch.
Once the basic sequence is completed, the system
clock hardware responds automatically as follows:
1.
The clock switching hardware compares the
COSC status bits with the new value of the
NOSC control bits. If they are the same, then the
clock switch is a redundant operation. In this
case, the OSWEN bit is cleared automatically
and the clock switch is aborted.
 2009 Microchip Technology Inc.
9.3
Fail-Safe Clock Monitor (FSCM)
The Fail-Safe Clock Monitor (FSCM) allows the device
to continue to operate even in the event of an oscillator
failure. The FSCM function is enabled by programming.
If the FSCM function is enabled, the LPRC internal
oscillator runs at all times (except during Sleep mode)
and is not subject to control by the Watchdog Timer.
If an oscillator failure occurs, the FSCM generates a
clock failure trap event and switches the system clock
over to the FRC oscillator. Then the application
program can either attempt to restart the oscillator or
execute a controlled shutdown. The trap can be treated
as a warm Reset by simply loading the Reset address
into the oscillator fail trap vector.
If the PLL multiplier is used to scale the system clock,
the internal FRC is also multiplied by the same factor
on clock failure. Essentially, the device switches to
FRC with PLL on a clock failure.
Preliminary
DS70592B-page 135
PIC24HJXXXGPX06A/X08A/X10A
NOTES:
DS70592B-page 136
Preliminary
 2009 Microchip Technology Inc.
PIC24HJXXXGPX06A/X08A/X10A
10.0
POWER-SAVING FEATURES
10.2
Note 1: This data sheet summarizes the features
of the PIC24HJXXXGPX06A/X08A/X10A
family of devices. However, it is not
intended to be a comprehensive
reference source. To complement the
information in this data sheet, refer to
Section 9. “Watchdog Timer and
Power-Saving Modes” (DS70236) of
the “dsPIC33F/PIC24H Family Reference
Manual”, which is available from the
Microchip website (www.microchip.com).
2: Some registers and associated bits
described in this section may not be available on all devices. Refer to Section 4.0
“Memory Organization” in this data
sheet for device-specific register and bit
information.
The PIC24HJXXXGPX06A/X08A/X10A devices provide the ability to manage power consumption by selectively managing clocking to the CPU and the
peripherals. In general, a lower clock frequency and a
reduction in the number of circuits being clocked constitutes
lower
consumed
power.
PIC24HJXXXGPX06A/X08A/X10A devices can manage power consumption in four different ways:
•
•
•
•
Clock frequency
Instruction-based Sleep and Idle modes
Software-controlled Doze mode
Selective peripheral control in software
Combinations of these methods can be used to selectively tailor an application’s power consumption while
still maintaining critical application features, such as
timing-sensitive communications.
10.1
Clock Frequency and Clock
Switching
PIC24HJXXXGPX06A/X08A/X10A devices allow a
wide range of clock frequencies to be selected under
application control. If the system clock configuration is
not locked, users can choose low-power or high-precision oscillators by simply changing the NOSC bits
(OSCCON<10:8>). The process of changing a system
clock during operation, as well as limitations to the process, are discussed in more detail in Section 9.0
“Oscillator Configuration”.
EXAMPLE 10-1:
Instruction-Based Power-Saving
Modes
PIC24HJXXXGPX06A/X08A/X10A devices have two
special power-saving modes that are entered through
the execution of a special PWRSAV instruction. Sleep
mode stops clock operation and halts all code execution. Idle mode halts the CPU and code execution, but
allows peripheral modules to continue operation. The
assembly syntax of the PWRSAV instruction is shown in
Example 10-1.
Note:
SLEEP_MODE and IDLE_MODE are
constants defined in the assembler
include file for the selected device.
Sleep and Idle modes can be exited as a result of an
enabled interrupt, WDT time-out or a device Reset. When
the device exits these modes, it is said to “wake-up”.
10.2.1
SLEEP MODE
Sleep mode has these features:
• The system clock source is shut down. If an
on-chip oscillator is used, it is turned off.
• The device current consumption is reduced to a
minimum, provided that no I/O pin is sourcing
current.
• The Fail-Safe Clock Monitor does not operate
during Sleep mode since the system clock source
is disabled.
• The LPRC clock continues to run in Sleep mode if
the WDT is enabled.
• The WDT, if enabled, is automatically cleared
prior to entering Sleep mode.
• Some device features or peripherals may continue
to operate in Sleep mode. This includes items such
as the input change notification on the I/O ports, or
peripherals that use an external clock input. Any
peripheral that requires the system clock source for
its operation is disabled in Sleep mode.
The device will wake-up from Sleep mode on any of
these events:
• Any interrupt source that is individually enabled.
• Any form of device Reset.
• A WDT time-out.
On wake-up from Sleep, the processor restarts with the
same clock source that was active when Sleep mode
was entered.
PWRSAV INSTRUCTION SYNTAX
PWRSAV #SLEEP_MODE
PWRSAV #IDLE_MODE
; Put the device into SLEEP mode
; Put the device into IDLE mode
 2009 Microchip Technology Inc.
Preliminary
DS70592B-page 137
PIC24HJXXXGPX06A/X08A/X10A
10.2.2
IDLE MODE
Idle mode has these features:
• The CPU stops executing instructions.
• The WDT is automatically cleared.
• The system clock source remains active. By
default, all peripheral modules continue to operate
normally from the system clock source, but can
also be selectively disabled (see Section 10.4
“Peripheral Module Disable”).
• If the WDT or FSCM is enabled, the LPRC also
remains active.
The device will wake from Idle mode on any of these
events:
• Any interrupt that is individually enabled.
• Any device Reset.
• A WDT time-out.
On wake-up from Idle, the clock is reapplied to the CPU
and instruction execution will begin (2-4 clock cycles
later), starting with the instruction following the PWRSAV
instruction, or the first instruction in the ISR.
10.2.3
INTERRUPTS COINCIDENT WITH
POWER SAVE INSTRUCTIONS
Any interrupt that coincides with the execution of a
PWRSAV instruction is held off until entry into Sleep or
Idle mode has completed. The device then wakes up
from Sleep or Idle mode.
10.3
Doze Mode
Generally, changing clock speed and invoking one of the
power-saving modes are the preferred strategies for
reducing power consumption. There may be circumstances, however, where this is not practical. For
example, it may be necessary for an application to maintain uninterrupted synchronous communication, even
while it is doing nothing else. Reducing system clock
speed may introduce communication errors, while using
a power-saving mode may stop communications
completely.
Doze mode is enabled by setting the DOZEN bit (CLKDIV<11>). The ratio between peripheral and core clock
speed is determined by the DOZE<2:0> bits (CLKDIV<14:12>). There are eight possible configurations,
from 1:1 to 1:128, with 1:1 being the default setting.
It is also possible to use Doze mode to selectively
reduce power consumption in event-driven applications. This allows clock-sensitive functions, such as
synchronous communications, to continue without
interruption while the CPU idles, waiting for something
to invoke an interrupt routine. Enabling the automatic
return to full-speed CPU operation on interrupts is
enabled by setting the ROI bit (CLKDIV<15>). By
default, interrupt events have no effect on Doze mode
operation.
For example, suppose the device is operating at
20 MIPS and the CAN module has been configured for
500 kbps based on this device operating speed. If the
device is now placed in Doze mode with a clock
frequency ratio of 1:4, the CAN module continues to
communicate at the required bit rate of 500 kbps, but
the CPU now starts executing instructions at a
frequency of 5 MIPS.
10.4
The Peripheral Module Disable (PMD) registers
provide a method to disable a peripheral module by
stopping all clock sources supplied to that module.
When a peripheral is disabled via the appropriate PMD
control bit, the peripheral is in a minimum power
consumption state. The control and status registers
associated with the peripheral are also disabled, so
writes to those registers will have no effect and read
values will be invalid.
A peripheral module is only enabled if both the associated bit in the PMD register is cleared and the peripheral
is supported by the specific dsPIC® DSC variant. If the
peripheral is present in the device, it is enabled in the
PMD register by default.
Note:
Doze mode is a simple and effective alternative method
to reduce power consumption while the device is still
executing code. In this mode, the system clock continues to operate from the same source and at the same
speed. Peripheral modules continue to be clocked at
the same speed, while the CPU clock speed is
reduced. Synchronization between the two clock
domains is maintained, allowing the peripherals to
access the SFRs while the CPU executes code at a
slower rate.
DS70592B-page 138
Peripheral Module Disable
Preliminary
If a PMD bit is set, the corresponding module is disabled after a delay of 1 instruction
cycle. Similarly, if a PMD bit is cleared, the
corresponding module is enabled after a
delay of 1 instruction cycle (assuming the
module control registers are already
configured to enable module operation).
 2009 Microchip Technology Inc.
PIC24HJXXXGPX06A/X08A/X10A
REGISTER 10-1:
PMD1: PERIPHERAL MODULE DISABLE CONTROL REGISTER 1
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
U-0
U-0
U-0
T5MD
T4MD
T3MD
T2MD
T1MD
—
—
—
bit 15
bit 8
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
I2C1MD
U2MD
U1MD
SPI2MD
SPI1MD
C2MD
C1MD
AD1MD(1)
bit 7
bit 0
Legend:
R = Readable bit
W = Writable bit
U = Unimplemented bit, read as ‘0’
-n = Value at POR
‘1’ = Bit is set
‘0’ = Bit is cleared
bit 15
T5MD: Timer5 Module Disable bit
1 = Timer5 module is disabled
0 = Timer5 module is enabled
bit 14
T4MD: Timer4 Module Disable bit
1 = Timer4 module is disabled
0 = Timer4 module is enabled
bit 13
T3MD: Timer3 Module Disable bit
1 = Timer3 module is disabled
0 = Timer3 module is enabled
bit 12
T2MD: Timer2 Module Disable bit
1 = Timer2 module is disabled
0 = Timer2 module is enabled
bit 11
T1MD: Timer1 Module Disable bit
1 = Timer1 module is disabled
0 = Timer1 module is enabled
bit 10-8
Unimplemented: Read as ‘0’
bit 7
I2C1MD: I2C1 Module Disable bit
1 = I2C1 module is disabled
0 = I2C1 module is enabled
bit 6
U2MD: UART2 Module Disable bit
1 = UART2 module is disabled
0 = UART2 module is enabled
bit 5
U1MD: UART1 Module Disable bit
1 = UART1 module is disabled
0 = UART1 module is enabled
bit 4
SPI2MD: SPI2 Module Disable bit
1 = SPI2 module is disabled
0 = SPI2 module is enabled
bit 3
SPI1MD: SPI1 Module Disable bit
1 = SPI1 module is disabled
0 = SPI1 module is enabled
bit 2
C2MD: ECAN2 Module Disable bit
1 = ECAN2 module is disabled
0 = ECAN2 module is enabled
 2009 Microchip Technology Inc.
Preliminary
x = Bit is unknown
DS70592B-page 139
PIC24HJXXXGPX06A/X08A/X10A
REGISTER 10-1:
PMD1: PERIPHERAL MODULE DISABLE CONTROL REGISTER 1 (CONTINUED)
bit 1
C1MD: ECAN1 Module Disable bit
1 = ECAN1 module is disabled
0 = ECAN1 module is enabled
bit 0
AD1MD: ADC1 Module Disable bit(1)
1 = ADC1 module is disabled
0 = ADC1 module is enabled
Note 1: PCFGx bits will have no effect if ADC module is disabled by setting this bit. In this case all port pins
multiplexed with ANx will be in Digital mode.
DS70592B-page 140
Preliminary
 2009 Microchip Technology Inc.
PIC24HJXXXGPX06A/X08A/X10A
REGISTER 10-2:
PMD2: PERIPHERAL MODULE DISABLE CONTROL REGISTER 2
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
IC8MD
IC7MD
IC6MD
IC5MD
IC4MD
IC3MD
IC2MD
IC1MD
bit 15
bit 8
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
OC8MD
OC7MD
OC6MD
OC5MD
OC4MD
OC3MD
OC2MD
OC1MD
bit 7
bit 0
Legend:
R = Readable bit
W = Writable bit
U = Unimplemented bit, read as ‘0’
-n = Value at POR
‘1’ = Bit is set
‘0’ = Bit is cleared
bit 15
IC8MD: Input Capture 8 Module Disable bit
1 = Input Capture 8 module is disabled
0 = Input Capture 8 module is enabled
bit 14
IC7MD: Input Capture 7 Module Disable bit
1 = Input Capture 7 module is disabled
0 = Input Capture 7 module is enabled
bit 13
IC6MD: Input Capture 6 Module Disable bit
1 = Input Capture 6 module is disabled
0 = Input Capture 6 module is enabled
bit 12
IC5MD: Input Capture 5 Module Disable bit
1 = Input Capture 5 module is disabled
0 = Input Capture 5 module is enabled
bit 11
IC4MD: Input Capture 4 Module Disable bit
1 = Input Capture 4 module is disabled
0 = Input Capture 4 module is enabled
bit 10
IC3MD: Input Capture 3 Module Disable bit
1 = Input Capture 3 module is disabled
0 = Input Capture 3 module is enabled
bit 9
IC2MD: Input Capture 2 Module Disable bit
1 = Input Capture 2 module is disabled
0 = Input Capture 2 module is enabled
bit 8
IC1MD: Input Capture 1 Module Disable bit
1 = Input Capture 1 module is disabled
0 = Input Capture 1 module is enabled
bit 7
OC8MD: Output Compare 8 Module Disable bit
1 = Output Compare 8 module is disabled
0 = Output Compare 8 module is enabled
bit 6
OC7MD: Output Compare 4 Module Disable bit
1 = Output Compare 7 module is disabled
0 = Output Compare 7 module is enabled
bit 5
OC6MD: Output Compare 6 Module Disable bit
1 = Output Compare 6 module is disabled
0 = Output Compare 6 module is enabled
bit 4
OC5MD: Output Compare 5 Module Disable bit
1 = Output Compare 5 module is disabled
0 = Output Compare 5 module is enabled
 2009 Microchip Technology Inc.
Preliminary
x = Bit is unknown
DS70592B-page 141
PIC24HJXXXGPX06A/X08A/X10A
REGISTER 10-2:
PMD2: PERIPHERAL MODULE DISABLE CONTROL REGISTER 2 (CONTINUED)
bit 3
OC4MD: Output Compare 4 Module Disable bit
1 = Output Compare 4 module is disabled
0 = Output Compare 4 module is enabled
bit 2
OC3MD: Output Compare 3 Module Disable bit
1 = Output Compare 3 module is disabled
0 = Output Compare 3 module is enabled
bit 1
OC2MD: Output Compare 2 Module Disable bit
1 = Output Compare 2 module is disabled
0 = Output Compare 2 module is enabled
bit 0
OC1MD: Output Compare 1 Module Disable bit
1 = Output Compare 1 module is disabled
0 = Output Compare 1 module is enabled
DS70592B-page 142
Preliminary
 2009 Microchip Technology Inc.
PIC24HJXXXGPX06A/X08A/X10A
REGISTER 10-3:
PMD3: PERIPHERAL MODULE DISABLE CONTROL REGISTER 3
R/W-0
R/W-0
R/W-0
R/W-0
U-0
U-0
U-0
U-0
T9MD
T8MD
T7MD
T6MD
—
—
—
—
bit 15
bit 8
U-0
U-0
U-0
U-0
U-0
U-0
R/W-0
R/W-0
—
—
—
—
—
—
I2C2MD
AD2MD(1)
bit 7
bit 0
Legend:
R = Readable bit
W = Writable bit
U = Unimplemented bit, read as ‘0’
-n = Value at POR
‘1’ = Bit is set
‘0’ = Bit is cleared
bit 15
T9MD: Timer9 Module Disable bit
1 = Timer9 module is disabled
0 = Timer9 module is enabled
bit 14
T8MD: Timer8 Module Disable bit
1 = Timer8 module is disabled
0 = Timer8 module is enabled
bit 13
T7MD: Timer7 Module Disable bit
1 = Timer7 module is disabled
0 = Timer7 module is enabled
bit 12
T6MD: Timer6 Module Disable bit
1 = Timer6 module is disabled
0 = Timer6 module is enabled
bit 11-2
Unimplemented: Read as ‘0’
bit 1
I2C2MD: I2C2 Module Disable bit
1 = I2C2 module is disabled
0 = I2C2 module is enabled
bit 0
AD2MD: AD2 Module Disable bit(1)
1 = AD2 module is disabled
0 = AD2 module is enabled
x = Bit is unknown
Note 1: PCFGx bits will have no effect if ADC module is disabled by setting this bit. In this case all port pins
multiplexed with ANx will be in Digital mode.
 2009 Microchip Technology Inc.
Preliminary
DS70592B-page 143
PIC24HJXXXGPX06A/X08A/X10A
NOTES:
DS70592B-page 144
Preliminary
 2009 Microchip Technology Inc.
PIC24HJXXXGPX06A/X08A/X10A
11.0
I/O PORTS
Note 1: This data sheet summarizes the features
of the PIC24HJXXXGPX06A/X08A/X10A
family of devices. However, it is not
intended to be a comprehensive
reference source. To complement the
information in this data sheet, refer to
Section 10. “I/O Ports” (DS70230) of
the “dsPIC33F/PIC24H Family Reference
Manual”, which is available from the
Microchip website (www.microchip.com).
2: Some registers and associated bits
described in this section may not be available on all devices. Refer to Section 4.0
“Memory Organization” in this data
sheet for device-specific register and bit
information.
All of the device pins (except VDD, VSS, MCLR and
OSC1/CLKIN) are shared between the peripherals and
the parallel I/O ports. All I/O input ports feature Schmitt
Trigger inputs for improved noise immunity.
11.1
Parallel I/O (PIO) Ports
A parallel I/O port that shares a pin with a peripheral is,
in general, subservient to the peripheral. The peripheral’s output buffer data and control signals are
provided to a pair of multiplexers. The multiplexers
select whether the peripheral or the associated port
has ownership of the output data and control signals of
the I/O pin. The logic also prevents “loop through”, in
FIGURE 11-1:
which a port’s digital output can drive the input of a
peripheral that shares the same pin. Figure 11-1 shows
how ports are shared with other peripherals and the
associated I/O pin to which they are connected.
When a peripheral is enabled and actively driving an
associated pin, the use of the pin as a general purpose
output pin is disabled. The I/O pin may be read, but the
output driver for the parallel port bit will be disabled. If
a peripheral is enabled, but the peripheral is not
actively driving a pin, that pin may be driven by a port.
All port pins have three registers directly associated
with their operation as digital I/O. The data direction
register (TRISx) determines whether the pin is an input
or an output. If the data direction bit is a ‘1’, then the pin
is an input. All port pins are defined as inputs after a
Reset. Reads from the latch (LATx), read the latch.
Writes to the latch, write the latch. Reads from the port
(PORTx), read the port pins, while writes to the port
pins, write the latch.
Any bit and its associated data and control registers
that are not valid for a particular device will be
disabled. That means the corresponding LATx and
TRISx registers and the port pins will read as zeros.
When a pin is shared with another peripheral or function that is defined as an input only, it is nonetheless
regarded as a dedicated port because there is no other
competing source of outputs. An example is the INT4
pin.
Note:
The voltage on a digital input pin can be
between -0.3V to 5.6V.
BLOCK DIAGRAM OF A TYPICAL SHARED PORT STRUCTURE
Peripheral Module
Output Multiplexers
Peripheral Input Data
Peripheral Module Enable
Peripheral Output Enable
Peripheral Output Data
I/O
1
Output Enable
0
PIO Module
1
Read TRIS
Output Data
0
Data Bus
WR TRIS
D
Q
I/O Pin
CK
TRIS Latch
D
WR LAT +
WR PORT
Q
CK
Data Latch
Read LAT
Input Data
Read Port
 2009 Microchip Technology Inc.
Preliminary
DS70592B-page 145
PIC24HJXXXGPX06A/X08A/X10A
11.2
Open-Drain Configuration
11.4
In addition to the PORT, LAT and TRIS registers for
data control, some port pins can also be individually
configured for either digital or open-drain output. This is
controlled by the Open-Drain Control register, ODCx,
associated with each port. Setting any of the bits configures the corresponding pin to act as an open-drain
output.
The open-drain feature allows the generation of
outputs higher than VDD (e.g., 5V) on any desired 5V
tolerant pins by using external pull-up resistors. The
maximum open-drain voltage allowed is the same as
the maximum VIH specification.
See the “Pin Diagrams (Continued)” for the available
pins and their functionality.
11.3
Configuring Analog Port Pins
The use of the ADxPCFGH, ADxPCFGL and TRIS
registers control the operation of the Analog-to-Digital
port pins. The port pins that are desired as analog
inputs must have their corresponding TRIS bit set
(input). If the TRIS bit is cleared (output), the digital output level (VOH or VOL) is converted.
Clearing any bit in the ADxPCFGH or ADxPCFGL register configures the corresponding bit to be an analog
pin. This is also the Reset state of any I/O pin that has
an analog (ANx) function associated with it.
Note:
In devices with two ADC modules, if the
corresponding PCFG bit in either
AD1PCFGH(L) and AD2PCFGH(L) is
cleared, the pin is configured as an analog
input.
I/O Port Write/Read Timing
One instruction cycle is required between a port
direction change or port write operation and a read
operation of the same port. Typically, this instruction
would be a NOP.
11.5
Input Change Notification
The input change notification function of the I/O ports
allows the PIC24HJXXXGPX06A/X08A/X10A devices
to generate interrupt requests to the processor in
response to a change-of-state on selected input pins.
This feature is capable of detecting input
change-of-states even in Sleep mode, when the clocks
are disabled. Depending on the device pin count, there
are up to 24 external signals (CN0 through CN23) that
can be selected (enabled) for generating an interrupt
request on a change-of-state.
There are four control registers associated with the CN
module. The CNEN1 and CNEN2 registers contain the
CN interrupt enable (CNxIE) control bits for each of the
CN input pins. Setting any of these bits enables a CN
interrupt for the corresponding pins.
Each CN pin also has a weak pull-up connected to it.
The pull-ups act as a current source that is connected
to the pin and eliminate the need for external resistors
when push button or keypad devices are connected.
The pull-ups are enabled separately using the CNPU1
and CNPU2 registers, which contain the weak pull-up
enable (CNxPUE) bits for each of the CN pins. Setting
any of the control bits enables the weak pull-ups for the
corresponding pins.
Note:
When reading the PORT register, all pins configured as
analog input channels will read as cleared (a low level).
Pull-ups on change notification pins
should always be disabled whenever the
port pin is configured as a digital output.
Pins configured as digital inputs will not convert an
analog input. Analog levels on any pin that is defined as
a digital input (including the ANx pins) can cause the
input buffer to consume current that exceeds the
device specifications.
Note:
The voltage on an analog input pin can be
between -0.3V to (VDD + 0.3 V).
EXAMPLE 11-1:
MOV
MOV
NOP
btss
PORT WRITE/READ EXAMPLE
0xFF00, W0
W0, TRISBB
PORTB, #13
DS70592B-page 146
;
;
;
;
Configure PORTB<15:8> as inputs
and PORTB<7:0> as outputs
Delay 1 cycle
Next Instruction
Preliminary
 2009 Microchip Technology Inc.
PIC24HJXXXGPX06A/X08A/X10A
12.0
TIMER1
Timer1 also supports these features:
• Timer gate operation
• Selectable prescaler settings
• Timer operation during CPU Idle and Sleep
modes
• Interrupt on 16-bit Period register match or falling
edge of external gate signal
Note 1: This data sheet summarizes the features
of the PIC24HJXXXGPX06A/X08A/X10A
family of devices. However, it is not
intended to be a comprehensive reference source. To complement the information in this data sheet, refer to Section 11.
“Timers” (DS70244) of the “dsPIC33F/
PIC24H Family Reference Manual”,
which is available from the Microchip
website (www.microchip.com).
Figure 12-1 presents a block diagram of the 16-bit
timer module.
To configure Timer1 for operation:
1.
2.
2: Some registers and associated bits
described in this section may not be available on all devices. Refer to Section 4.0
“Memory Organization” in this data
sheet for device-specific register and bit
information.
3.
4.
The Timer1 module is a 16-bit timer, which can serve
as the time counter for the real-time clock, or operate
as a free-running interval timer/counter. Timer1 can
operate in three modes:
5.
6.
• 16-bit Timer
• 16-bit Synchronous Counter
• 16-bit Asynchronous Counter
FIGURE 12-1:
Set the TON bit (= 1) in the T1CON register.
Select the timer prescaler ratio using the
TCKPS<1:0> bits in the T1CON register.
Set the Clock and Gating modes using the TCS
and TGATE bits in the T1CON register.
Set or clear the TSYNC bit in T1CON to select
synchronous or asynchronous operation.
Load the timer period value into the PR1
register.
If interrupts are required, set the interrupt enable
bit, T1IE. Use the priority bits, T1IP<2:0>, to set
the interrupt priority.
16-BIT TIMER1 MODULE BLOCK DIAGRAM
TCKPS<1:0>
2
TON
SOSCO/
T1CK
1x
SOSCEN
SOSCI
Gate
Sync
01
TCY
00
Prescaler
1, 8, 64, 256
TGATE
TCS
TGATE
1
Q
D
0
Q
CK
Set T1IF
Reset
0
TMR1
1
Comparator
Sync
TSYNC
Equal
PR1
 2009 Microchip Technology Inc.
Preliminary
DS70592B-page 147
PIC24HJXXXGPX06A/X08A/X10A
REGISTER 12-1:
T1CON: TIMER1 CONTROL REGISTER
R/W-0
U-0
R/W-0
U-0
U-0
U-0
U-0
U-0
TON
—
TSIDL
—
—
—
—
—
bit 15
bit 8
U-0
R/W-0
—
TGATE
R/W-0
R/W-0
TCKPS<1:0>
U-0
R/W-0
R/W-0
U-0
—
TSYNC
TCS
—
bit 7
bit 0
Legend:
R = Readable bit
W = Writable bit
U = Unimplemented bit, read as ‘0’
-n = Value at POR
‘1’ = Bit is set
‘0’ = Bit is cleared
bit 15
TON: Timer1 On bit
1 = Starts 16-bit Timer1
0 = Stops 16-bit Timer1
bit 14
Unimplemented: Read as ‘0’
bit 13
TSIDL: Stop in Idle Mode bit
1 = Discontinue module operation when device enters Idle mode
0 = Continue module operation in Idle mode
bit 12-7
Unimplemented: Read as ‘0’
bit 6
TGATE: Timer1 Gated Time Accumulation Enable bit
When T1CS = 1:
This bit is ignored.
When T1CS = 0:
1 = Gated time accumulation enabled
0 = Gated time accumulation disabled
bit 5-4
TCKPS<1:0>: Timer1 Input Clock Prescale Select bits
11 = 1:256
10 = 1:64
01 = 1:8
00 = 1:1
bit 3
Unimplemented: Read as ‘0’
bit 2
TSYNC: Timer1 External Clock Input Synchronization Select bit
When TCS = 1:
1 = Synchronize external clock input
0 = Do not synchronize external clock input
When TCS = 0:
This bit is ignored.
bit 1
TCS: Timer1 Clock Source Select bit
1 = External clock from pin T1CK (on the rising edge)
0 = Internal clock (FCY)
bit 0
Unimplemented: Read as ‘0’
DS70592B-page 148
Preliminary
x = Bit is unknown
 2009 Microchip Technology Inc.
PIC24HJXXXGPX06A/X08A/X10A
13.0
TIMER2/3, TIMER4/5, TIMER6/7
AND TIMER8/9
Note 1: This data sheet summarizes the features
of the PIC24HJXXXGPX06A/X08A/X10A
family of devices. However, it is not
intended to be a comprehensive reference source. To complement the information in this data sheet, refer to Section 11.
“Timers” (DS70244) of the “dsPIC33F/
PIC24H Family Reference Manual”,
which is available from the Microchip
website (www.microchip.com).
2: Some registers and associated bits
described in this section may not be available on all devices. Refer to Section 4.0
“Memory Organization” in this data
sheet for device-specific register and bit
information.
The Timer2/3, Timer4/5, Timer6/7 and Timer8/9
modules are 32-bit timers, which can also be configured as four independent 16-bit timers with selectable
operating modes.
As a 32-bit timer, Timer2/3, Timer4/5, Timer6/7 and
Timer8/9 operate in three modes:
For 32-bit timer/counter operation, Timer2, Timer4,
Timer6 or Timer8 is the least significant word; Timer3,
Timer5, Timer7 or Timer9 is the most significant word
of the 32-bit timers.
Note:
To configure Timer2/3, Timer4/5, Timer6/7 or Timer8/9
for 32-bit operation:
1.
2.
3.
4.
5.
• Two Independent 16-bit Timers (e.g., Timer2 and
Timer3) with all 16-bit operating modes (except
Asynchronous Counter mode)
• Single 32-bit Timer
• Single 32-bit Synchronous Counter
They also support these features:
6.
•
•
•
•
•
Timer Gate Operation
Selectable Prescaler Settings
Timer Operation during Idle and Sleep modes
Interrupt on a 32-bit Period Register Match
Time Base for Input Capture and Output Compare
Modules (Timer2 and Timer3 only)
• ADC1 Event Trigger (Timer2/3 only)
• ADC2 Event Trigger (Timer4/5 only)
Individually, all eight of the 16-bit timers can function as
synchronous timers or counters. They also offer the
features listed above, except for the event trigger; this
is implemented only with Timer2/3. The operating
modes and enabled features are determined by setting
the appropriate bit(s) in the T2CON, T3CON, T4CON,
T5CON, T6CON, T7CON, T8CON and T9CON registers. T2CON, T4CON, T6CON and T8CON are shown
in generic form in Register 13-1. T3CON, T5CON,
T7CON and T9CON are shown in Register 13-2.
Set the corresponding T32 control bit.
Select the prescaler ratio for Timer2, Timer4,
Timer6 or Timer8 using the TCKPS<1:0> bits.
Set the Clock and Gating modes using the
corresponding TCS and TGATE bits.
Load the timer period value. PR3, PR5, PR7 or
PR9 contains the most significant word of the
value, while PR2, PR4, PR6 or PR8 contains the
least significant word.
If interrupts are required, set the interrupt enable
bit, T3IE, T5IE, T7IE or T9IE. Use the priority
bits, T3IP<2:0>, T5IP<2:0>, T7IP<2:0> or
T9IP<2:0>, to set the interrupt priority. While
Timer2, Timer4, Timer6 or Timer8 control the
timer, the interrupt appears as a Timer3, Timer5,
Timer7 or Timer9 interrupt.
Set the corresponding TON bit.
The timer value at any point is stored in the register
pair, TMR3:TMR2, TMR5:TMR4, TMR7:TMR6 or
TMR9:TMR8. TMR3, TMR5, TMR7 or TMR9 always
contains the most significant word of the count, while
TMR2, TMR4, TMR6 or TMR8 contains the least
significant word.
To configure any of the timers for individual 16-bit
operation:
1.
2.
3.
4.
5.
6.
 2009 Microchip Technology Inc.
For 32-bit operation, T3CON, T5CON,
T7CON and T9CON control bits are
ignored. Only T2CON, T4CON, T6CON
and T8CON control bits are used for setup
and control. Timer2, Timer4, Timer6 and
Timer8 clock and gate inputs are utilized
for the 32-bit timer modules, but an interrupt is generated with the Timer3, Timer5,
Ttimer7 and Timer9 interrupt flags.
Preliminary
Clear the T32 bit corresponding to that timer.
Select the timer prescaler ratio using the
TCKPS<1:0> bits.
Set the Clock and Gating modes using the TCS
and TGATE bits.
Load the timer period value into the PRx
register.
If interrupts are required, set the interrupt enable
bit, TxIE. Use the priority bits, TxIP<2:0>, to set
the interrupt priority.
Set the TON bit.
DS70592B-page 149
PIC24HJXXXGPX06A/X08A/X10A
A block diagram for a 32-bit timer pair (Timer4/5)
example is shown in Figure 13-1 and a timer (Timer4)
operating in 16-bit mode example is shown in
Figure 13-2.
Note:
Only Timer2 and Timer3 can trigger a
DMA data transfer.
TIMER2/3 (32-BIT) BLOCK DIAGRAM(1)
FIGURE 13-1:
T2CK
1x
Gate
Sync
01
TCY
00
TCKPS<1:0>
2
TON
Prescaler
1, 8, 64, 256
TGATE
TCS
TGATE
Q
1
Set T3IF
Q
D
CK
0
PR2
PR3
ADC Event Trigger(2)
Equal
Comparator
MSb
LSb
TMR3
Reset
TMR2
Sync
16
Read TMR2
Write TMR2
16
16
TMR3HLD
16
Data Bus<15:0>
Note 1:
2:
The 32-bit timer control bit, T32, must be set for 32-bit timer/counter operation. All control bits are respective
to the T2CON register.
The ADC event trigger is available only on Timer2/3.
DS70592B-page 150
Preliminary
 2009 Microchip Technology Inc.
PIC24HJXXXGPX06A/X08A/X10A
FIGURE 13-2:
TIMER2 (16-BIT) BLOCK DIAGRAM
TON
T2CK
TCKPS<1:0>
2
1x
Gate
Sync
Prescaler
1, 8, 64, 256
01
00
TGATE
TCS
TCY
1
Set T2IF
Q
D
Q
CK
TGATE
0
Reset
Sync
TMR2
Comparator
Equal
PR2
 2009 Microchip Technology Inc.
Preliminary
DS70592B-page 151
PIC24HJXXXGPX06A/X08A/X10A
REGISTER 13-1:
TxCON (T2CON, T4CON, T6CON OR T8CON) CONTROL REGISTER
R/W-0
U-0
R/W-0
U-0
U-0
U-0
U-0
U-0
TON
—
TSIDL
—
—
—
—
—
bit 15
bit 8
U-0
R/W-0
—
TGATE
R/W-0
R/W-0
TCKPS<1:0>
R/W-0
U-0
R/W-0
U-0
T32
—
TCS(1)
—
bit 7
bit 0
Legend:
R = Readable bit
W = Writable bit
U = Unimplemented bit, read as ‘0’
-n = Value at POR
‘1’ = Bit is set
‘0’ = Bit is cleared
bit 15
TON: Timerx On bit
When T32 = 1:
1 = Starts 32-bit Timerx/y
0 = Stops 32-bit Timerx/y
When T32 = 0:
1 = Starts 16-bit Timerx
0 = Stops 16-bit Timerx
bit 14
Unimplemented: Read as ‘0’
bit 13
TSIDL: Stop in Idle Mode bit
1 = Discontinue module operation when device enters Idle mode
0 = Continue module operation in Idle mode
bit 12-7
Unimplemented: Read as ‘0’
bit 6
TGATE: Timerx Gated Time Accumulation Enable bit
When TCS = 1:
This bit is ignored.
When TCS = 0:
1 = Gated time accumulation enabled
0 = Gated time accumulation disabled
bit 5-4
TCKPS<1:0>: Timerx Input Clock Prescale Select bits
11 = 1:256
10 = 1:64
01 = 1:8
00 = 1:1
bit 3
T32: 32-bit Timer Mode Select bit
1 = Timerx and Timery form a single 32-bit timer
0 = Timerx and Timery act as two 16-bit timers
bit 2
Unimplemented: Read as ‘0’
bit 1
TCS: Timerx Clock Source Select bit(1)
1 = External clock from pin TxCK (on the rising edge)
0 = Internal clock (FCY)
bit 0
Unimplemented: Read as ‘0’
x = Bit is unknown
Note 1: The TxCK pin is not available on all timers. Refer to the “Pin Diagrams” section for the available pins.
DS70592B-page 152
Preliminary
 2009 Microchip Technology Inc.
PIC24HJXXXGPX06A/X08A/X10A
REGISTER 13-2:
TyCON (T3CON, T5CON, T7CON OR T9CON) CONTROL REGISTER
R/W-0
U-0
R/W-0
U-0
U-0
U-0
U-0
U-0
TON(1)
—
TSIDL(2)
—
—
—
—
—
bit 15
bit 8
U-0
R/W-0
—
TGATE(1)
R/W-0
R/W-0
TCKPS<1:0>(1)
U-0
U-0
R/W-0
U-0
—
—
TCS(1,3)
—
bit 7
bit 0
Legend:
R = Readable bit
W = Writable bit
U = Unimplemented bit, read as ‘0’
-n = Value at POR
‘1’ = Bit is set
‘0’ = Bit is cleared
bit 15
TON: Timery On bit(1)
1 = Starts 16-bit Timery
0 = Stops 16-bit Timery
bit 14
Unimplemented: Read as ‘0’
bit 13
TSIDL: Stop in Idle Mode bit(2)
1 = Discontinue module operation when device enters Idle mode
0 = Continue module operation in Idle mode
bit 12-7
Unimplemented: Read as ‘0’
bit 6
TGATE: Timery Gated Time Accumulation Enable bit(1)
When TCS = 1:
This bit is ignored.
When TCS = 0:
1 = Gated time accumulation enabled
0 = Gated time accumulation disabled
bit 5-4
TCKPS<1:0>: Timer3 Input Clock Prescale Select bits(1)
11 = 1:256
10 = 1:64
01 = 1:8
00 = 1:1
bit 3-2
Unimplemented: Read as ‘0’
bit 1
TCS: Timery Clock Source Select bit(1,3)
1 = External clock from pin TyCK (on the rising edge)
0 = Internal clock (FCY)
bit 0
Unimplemented: Read as ‘0’
x = Bit is unknown
Note 1: When 32-bit operation is enabled (T2CON<3> = 1), these bits have no effect on Timery operation; all timer
functions are set through T2CON.
2: When 32-bit timer operation is enabled (T32 = 1) in the Timer Control register (TxCON<3>), the TSIDL bit
must be cleared to operate the 32-bit timer in Idle mode.
3: The TyCK pin is not available on all timers. Refer to the “Pin Diagrams” section for the available pins.
 2009 Microchip Technology Inc.
Preliminary
DS70592B-page 153
PIC24HJXXXGPX06A/X08A/X10A
NOTES:
DS70592B-page 154
Preliminary
 2009 Microchip Technology Inc.
PIC24HJXXXGPX06A/X08A/X10A
14.0
INPUT CAPTURE
2.
Note 1: This data sheet summarizes the features
of the PIC24HJXXXGPX06A/X08A/X10A
family of devices. However, it is not
intended to be a comprehensive reference source. To complement the information in this data sheet, refer to the
“dsPIC33F/PIC24H Family Reference
Manual”, Section 12. “Input Capture”
(DS70248), which is available from the
Microchip website (www.microchip.com).
2: Some registers and associated bits
described in this section may not be available on all devices. Refer to Section 4.0
“Memory Organization” in this data
sheet for device-specific register and bit
information.
The input capture module is useful in applications
requiring frequency (period) and pulse measurement.
The
PIC24HJXXXGPX06A/X08A/X10A
devices
support up to eight input capture channels.
3.
Each input capture channel can select between one of
two 16-bit timers (Timer2 or Timer3) for the time base.
The selected timer can use either an internal or external clock.
Other operational features include:
• Device wake-up from capture pin during CPU
Sleep and Idle modes
• Interrupt on input capture event
• 4-word FIFO buffer for capture values
- Interrupt optionally generated after 1, 2, 3 or
4 buffer locations are filled
• Input capture can also be used to provide
additional sources of external interrupts.
Note:
The input capture module captures the 16-bit value of
the selected Time Base register when an event occurs
at the ICx pin. The events that cause a capture event
are listed below in three categories:
1.
Capture timer value on every edge (rising and
falling)
Prescaler Capture Event modes
-Capture timer value on every 4th rising edge
of input at ICx pin
-Capture timer value on every 16th rising
edge of input at ICx pin
Only IC1 and IC2 can trigger a DMA data
transfer. If DMA data transfers are
required, the FIFO buffer size must be set
to 1 (ICI<1:0> = 00).
Simple Capture Event modes
-Capture timer value on every falling edge of
input at ICx pin
-Capture timer value on every rising edge of
input at ICx pin
FIGURE 14-1:
INPUT CAPTURE BLOCK DIAGRAM
From 16-bit Timers
TMRy TMRz
16
16
1
Edge Detection Logic
and
Clock Synchronizer
Prescaler
Counter
(1, 4, 16)
0
FIFO
R/W
Logic
ICTMR
(ICxCON<7>)
ICx Pin
ICM<2:0> (ICxCON<2:0>)
Mode Select
FIFO
3
ICOV, ICBNE (ICxCON<4:3>)
ICxBUF
ICxI<1:0>
ICxCON
Interrupt
Logic
System Bus
Set Flag ICxIF
(in IFSn Register)
Note: An ‘x’ in a signal, register or bit name denotes the number of the capture channel.
 2009 Microchip Technology Inc.
Preliminary
DS70592B-page 155
PIC24HJXXXGPX06A/X08A/X10A
14.1
Input Capture Registers
REGISTER 14-1:
ICxCON: INPUT CAPTURE x CONTROL REGISTER
U-0
U-0
R/W-0
U-0
U-0
U-0
U-0
U-0
—
—
ICSIDL
—
—
—
—
—
bit 15
bit 8
R/W-0
R/W-0
ICTMR(1)
R/W-0
ICI<1:0>
R-0, HC
R-0, HC
ICOV
ICBNE
R/W-0
R/W-0
R/W-0
ICM<2:0>
bit 7
bit 0
Legend:
R = Readable bit
W = Writable bit
U = Unimplemented bit, read as ‘0’
-n = Value at POR
‘1’ = Bit is set
‘0’ = Bit is cleared
x = Bit is unknown
bit 15-14
Unimplemented: Read as ‘0’
bit 13
ICSIDL: Input Capture Module Stop in Idle Control bit
1 = Input capture module will halt in CPU Idle mode
0 = Input capture module will continue to operate in CPU Idle mode
bit 12-8
Unimplemented: Read as ‘0’
bit 7
ICTMR: Input Capture Timer Select bits(1)
1 = TMR2 contents are captured on capture event
0 = TMR3 contents are captured on capture event
bit 6-5
ICI<1:0>: Select Number of Captures per Interrupt bits
11 = Interrupt on every fourth capture event
10 = Interrupt on every third capture event
01 = Interrupt on every second capture event
00 = Interrupt on every capture event
bit 4
ICOV: Input Capture Overflow Status Flag bit (read-only)
1 = Input capture overflow occurred
0 = No input capture overflow occurred
bit 3
ICBNE: Input Capture Buffer Empty Status bit (read-only)
1 = Input capture buffer is not empty, at least one more capture value can be read
0 = Input capture buffer is empty
bit 2-0
ICM<2:0>: Input Capture Mode Select bits
111 = Input capture functions as interrupt pin only when device is in Sleep or Idle mode
(Rising edge detect only, all other control bits are not applicable.)
110 = Unused (module disabled)
101 = Capture mode, every 16th rising edge
100 = Capture mode, every 4th rising edge
011 = Capture mode, every rising edge
010 = Capture mode, every falling edge
001 = Capture mode, every edge (rising and falling)
(ICI<1:0> bits do not control interrupt generation for this mode.)
000 = Input capture module turned off
Note 1: Timer selections may vary. Refer to the device data sheet for details.
DS70592B-page 156
Preliminary
 2009 Microchip Technology Inc.
PIC24HJXXXGPX06A/X08A/X10A
15.0
OUTPUT COMPARE
Note 1: This data sheet summarizes the features
of the PIC24HJXXXGPX06A/X08A/X10A
families of devices. It is not intended to be
a comprehensive reference source. To
complement the information in this data
sheet, refer to the “dsPIC33F/PIC24H
Family Reference Manual”, Section 13.
“Output Compare” (DS70247), which is
available on the Microchip web site
(www.microchip.com).
2: Some registers and associated bits
described in this section may not be available on all devices. Refer to Section 4.0
“Memory Organization” in this data
sheet for device-specific register and bit
information.
FIGURE 15-1:
The output compare module can select either Timer2 or
Timer3 for its time base. The module compares the
value of the timer with the value of one or two Compare
registers depending on the operating mode selected.
The state of the output pin changes when the timer
value matches the Compare register value. The output
compare module generates either a single output
pulse, or a sequence of output pulses, by changing the
state of the output pin on the compare match events.
The output compare module can also generate interrupts on compare match events.
The output compare module has multiple operating
modes:
•
•
•
•
•
•
•
Active-Low One-Shot mode
Active-High One-Shot mode
Toggle mode
Delayed One-Shot mode
Continuous Pulse mode
PWM mode without Fault Protection
PWM mode with Fault Protection
OUTPUT COMPARE MODULE BLOCK DIAGRAM
Set Flag bit
OCxIF(1)
OCxRS(1)
Output
Logic
OCxR(1)
3
16
1
2:
Output Enable
OCTSEL
0
1
TMR2
Rollover
TMR3
Rollover
OCFA
or
OCFB(2)
16
TMR2 TMR3
Note 1:
OCx(1)
OCM<2:0>
Mode Select
Comparator
0
S Q
R
An ‘x’ in a signal, register or bit name denotes the number of the output compare channels.
The OCFA pin controls OC1 through OC4. The OCFB pin controls OC5 through OC8.
 2009 Microchip Technology Inc.
Preliminary
DS70592B-page 157
PIC24HJXXXGPX06A/X08A/X10A
15.1
Output Compare Modes
application must disable the associated timer when
writing to the Output Compare Control registers to
avoid malfunctions.
Configure the Output Compare modes by setting the
appropriate Output Compare Mode (OCM<2:0>) bits in
the Output Compare Control (OCxCON<2:0>) register.
Table 15-1 lists the different bit settings for the Output
Compare modes. Figure 15-2 illustrates the output
compare operation for various modes. The user
TABLE 15-1:
Note:
See Section 13. “Output Compare”
(DS70247) in the “dsPIC33F/PIC24H
Family Reference Manual” for OCxR and
OCxRS register restrictions.
OUTPUT COMPARE MODES
OCM<2:0>
Mode
OCx Pin Initial State
OCx Interrupt Generation
000
Module Disabled
001
Active-Low One-Shot
010
Active-High One-Shot
011
Toggle
100
Delayed One-Shot
0
OCx falling edge
101
Continuous Pulse
0
OCx falling edge
110
PWM without Fault Protection
‘0’, if OCxR is zero
‘1’, if OCxR is non-zero
No interrupt
111
PWM with Fault Protection
‘0’, if OCxR is zero
‘1’, if OCxR is non-zero
OCFA falling edge for OC1 to OC4
FIGURE 15-2:
Controlled by GPIO register
—
0
OCx rising edge
1
OCx falling edge
Current output is maintained
OCx rising and falling edge
OUTPUT COMPARE OPERATION
Output Compare
Mode Enabled
Timer is Reset on
Period Match
OCxRS
TMRy
OCxR
Active-Low One-Shot
(OCM = 001)
Active-High One-Shot
(OCM = 010)
Toggle
(OCM = 011)
Delayed One-Shot
(OCM = 100)
Continuous Pulse
(OCM = 101)
PWM
(OCM = 110 or 111)
DS70592B-page 158
Preliminary
 2009 Microchip Technology Inc.
PIC24HJXXXGPX06A/X08A/X10A
REGISTER 15-1:
OCxCON: OUTPUT COMPARE x CONTROL REGISTER (x = 1, 2)
U-0
U-0
R/W-0
U-0
U-0
U-0
U-0
U-0
—
—
OCSIDL
—
—
—
—
—
bit 15
bit 8
U-0
U-0
U-0
R-0, HC
R/W-0
—
—
—
OCFLT
OCTSEL
R/W-0
R/W-0
R/W-0
OCM<2:0>
bit 7
bit 0
Legend:
HC = Hardware Clearable bit
R = Readable bit
W = Writable bit
U = Unimplemented bit, read as ‘0’
-n = Value at POR
‘1’ = Bit is set
‘0’ = Bit is cleared
x = Bit is unknown
bit 15-14
Unimplemented: Read as ‘0’
bit 13
OCSIDL: Stop Output Compare in Idle Mode Control bit
1 = Output Compare x halts in CPU Idle mode
0 = Output Compare x continues to operate in CPU Idle mode
bit 12-5
Unimplemented: Read as ‘0’
bit 4
OCFLT: PWM Fault Condition Status bit
1 = PWM Fault condition has occurred (cleared in hardware only)
0 = No PWM Fault condition has occurred (this bit is only used when OCM<2:0> = 111)
bit 3
OCTSEL: Output Compare Timer Select bit
1 = Timer3 is the clock source for Compare x
0 = Timer2 is the clock source for Compare x
bit 2-0
OCM<2:0>: Output Compare Mode Select bits
111 = PWM mode on OCx, Fault pin enabled
110 = PWM mode on OCx, Fault pin disabled
101 = Initialize OCx pin low, generate continuous output pulses on OCx pin
100 = Initialize OCx pin low, generate single output pulse on OCx pin
011 = Compare event toggles OCx pin
010 = Initialize OCx pin high, compare event forces OCx pin low
001 = Initialize OCx pin low, compare event forces OCx pin high
000 = Output compare channel is disabled
 2009 Microchip Technology Inc.
Preliminary
DS70592B-page 159
PIC24HJXXXGPX06A/X08A/X10A
NOTES:
DS70592B-page 160
Preliminary
 2009 Microchip Technology Inc.
PIC24HJXXXGPX06A/X08A/X10A
16.0
SERIAL PERIPHERAL
INTERFACE (SPI)
Note 1: This data sheet summarizes the features
of the PIC24HJXXXGPX06A/X08A/X10A
family of devices. However, it is not
intended to be a comprehensive reference source. To complement the information in this data sheet, refer to the
“dsPIC33F/PIC24H Family Reference
Manual“, Section 18. “Serial Peripheral
Interface (SPI)” (DS70243), which is
available from the Microchip website
(www.microchip.com).
2: Some registers and associated bits
described in this section may not be available on all devices. Refer to Section 4.0
“Memory Organization” in this data
sheet for device-specific register and bit
information.
The Serial Peripheral Interface (SPI) module is a synchronous serial interface useful for communicating with
other peripheral or microcontroller devices. These
peripheral devices may be serial EEPROMs, shift registers, display drivers, Analog-to-Digital converters, etc.
The SPI module is compatible with SPI and SIOP from
Motorola®.
Note:
In this section, the SPI modules are
referred to together as SPIx, or separately
as SPI1 and SPI2. Special Function Registers will follow a similar notation. For
example, SPIxCON refers to the control
register for the SPI1 or SPI2 module.
Each SPI module consists of a 16-bit shift register,
SPIxSR (where x = 1 or 2), used for shifting data in and
out, and a buffer register, SPIxBUF. A control register,
SPIxCON, configures the module. Additionally, a status
register, SPIxSTAT, indicates various status conditions.
The serial interface consists of 4 pins: SDIx (serial data
input), SDOx (serial data output), SCKx (shift clock
input or output), and SSx (active-low slave select).
In Master mode operation, SCK is a clock output but in
Slave mode, it is a clock input.
FIGURE 16-1:
SPI MODULE BLOCK DIAGRAM
SCKx
1:1 to 1:8
Secondary
Prescaler
1:1/4/16/64
Primary
Prescaler
FCY
SSx
Sync
Control
Select
Edge
Control
Clock
SPIxCON1<1:0>
Shift Control
SPIxCON1<4:2>
SDOx
Enable
Master Clock
bit 0
SDIx
SPIxSR
Transfer
Transfer
SPIxRXB
SPIxTXB
SPIxBUF
Read SPIxBUF
Write SPIxBUF
16
Internal Data Bus
 2009 Microchip Technology Inc.
Preliminary
DS70592B-page 161
PIC24HJXXXGPX06A/X08A/X10A
REGISTER 16-1:
SPIxSTAT: SPIx STATUS AND CONTROL REGISTER
R/W-0
U-0
R/W-0
U-0
U-0
U-0
U-0
U-0
SPIEN
—
SPISIDL
—
—
—
—
—
bit 15
bit 8
U-0
R/C-0
U-0
U-0
U-0
U-0
R-0
R-0
—
SPIROV
—
—
—
—
SPITBF
SPIRBF
bit 7
bit 0
Legend:
C = Clearable bit
R = Readable bit
W = Writable bit
U = Unimplemented bit, read as ‘0’
-n = Value at POR
‘1’ = Bit is set
‘0’ = Bit is cleared
x = Bit is unknown
bit 15
SPIEN: SPIx Enable bit
1 = Enables module and configures SCKx, SDOx, SDIx and SSx as serial port pins
0 = Disables module
bit 14
Unimplemented: Read as ‘0’
bit 13
SPISIDL: Stop in Idle Mode bit
1 = Discontinue module operation when device enters Idle mode
0 = Continue module operation in Idle mode
bit 12-7
Unimplemented: Read as ‘0’
bit 6
SPIROV: Receive Overflow Flag bit
1 = A new byte/word is completely received and discarded. The user software has not read the
previous data in the SPIxBUF register
0 = No overflow has occurred
bit 5-2
Unimplemented: Read as ‘0’
bit 1
SPITBF: SPIx Transmit Buffer Full Status bit
1 = Transmit not yet started, SPIxTXB is full
0 = Transmit started, SPIxTXB is empty
Automatically set in hardware when CPU writes SPIxBUF location, loading SPIxTXB.
Automatically cleared in hardware when SPIx module transfers data from SPIxTXB to SPIxSR.
bit 0
SPIRBF: SPIx Receive Buffer Full Status bit
1 = Receive complete, SPIxRXB is full
0 = Receive is not complete, SPIxRXB is empty
Automatically set in hardware when SPIx transfers data from SPIxSR to SPIxRXB.
Automatically cleared in hardware when core reads SPIxBUF location, reading SPIxRXB.
DS70592B-page 162
Preliminary
 2009 Microchip Technology Inc.
PIC24HJXXXGPX06A/X08A/X10A
REGISTER 16-2:
SPIXCON1: SPIx CONTROL REGISTER 1
U-0
U-0
U-0
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
—
—
—
DISSCK
DISSDO
MODE16
SMP
CKE(1)
bit 15
bit 8
R/W-0
R/W-0
R/W-0
SSEN(3)
CKP
MSTEN
R/W-0
R/W-0
R/W-0
R/W-0
SPRE<2:0>(2)
R/W-0
PPRE<1:0>(2)
bit 7
bit 0
Legend:
R = Readable bit
W = Writable bit
U = Unimplemented bit, read as ‘0’
-n = Value at POR
‘1’ = Bit is set
‘0’ = Bit is cleared
x = Bit is unknown
bit 15-13
Unimplemented: Read as ‘0’
bit 12
DISSCK: Disable SCKx pin bit (SPI Master modes only)
1 = Internal SPI clock is disabled, pin functions as I/O
0 = Internal SPI clock is enabled
bit 11
DISSDO: Disable SDOx pin bit
1 = SDOx pin is not used by module; pin functions as I/O
0 = SDOx pin is controlled by the module
bit 10
MODE16: Word/Byte Communication Select bit
1 = Communication is word-wide (16 bits)
0 = Communication is byte-wide (8 bits)
bit 9
SMP: SPIx Data Input Sample Phase bit
Master mode:
1 = Input data sampled at end of data output time
0 = Input data sampled at middle of data output time
Slave mode:
SMP must be cleared when SPIx is used in Slave mode.
bit 8
CKE: SPIx Clock Edge Select bit(1)
1 = Serial output data changes on transition from active clock state to Idle clock state (see bit 6)
0 = Serial output data changes on transition from Idle clock state to active clock state (see bit 6)
bit 7
SSEN: Slave Select Enable bit (Slave mode)(3)
1 = SSx pin used for Slave mode
0 = SSx pin not used by module. Pin controlled by port function
bit 6
CKP: Clock Polarity Select bit
1 = Idle state for clock is a high level; active state is a low level
0 = Idle state for clock is a low level; active state is a high level
bit 5
MSTEN: Master Mode Enable bit
1 = Master mode
0 = Slave mode
Note 1: The CKE bit is not used in the Framed SPI modes. The user should program this bit to ‘0’ for the Framed
SPI modes (FRMEN = 1).
2: Do not set both Primary and Secondary prescalers to a value of 1:1.
3: This bit must be cleared when FRMEN = 1.
 2009 Microchip Technology Inc.
Preliminary
DS70592B-page 163
PIC24HJXXXGPX06A/X08A/X10A
REGISTER 16-2:
SPIXCON1: SPIx CONTROL REGISTER 1 (CONTINUED)
bit 4-2
SPRE<2:0>: Secondary Prescale bits (Master mode)(2)
111 = Secondary prescale 1:1
110 = Secondary prescale 2:1
•
•
•
000 = Secondary prescale 8:1
bit 1-0
PPRE<1:0>: Primary Prescale bits (Master mode)(2)
11 = Primary prescale 1:1
10 = Primary prescale 4:1
01 = Primary prescale 16:1
00 = Primary prescale 64:1
Note 1: The CKE bit is not used in the Framed SPI modes. The user should program this bit to ‘0’ for the Framed
SPI modes (FRMEN = 1).
2: Do not set both Primary and Secondary prescalers to a value of 1:1.
3: This bit must be cleared when FRMEN = 1.
DS70592B-page 164
Preliminary
 2009 Microchip Technology Inc.
PIC24HJXXXGPX06A/X08A/X10A
REGISTER 16-3:
SPIxCON2: SPIx CONTROL REGISTER 2
R/W-0
R/W-0
R/W-0
U-0
U-0
U-0
U-0
U-0
FRMEN
SPIFSD
FRMPOL
—
—
—
—
—
bit 15
bit 8
U-0
U-0
U-0
U-0
U-0
U-0
R/W-0
U-0
—
—
—
—
—
—
FRMDLY
—
bit 7
bit 0
Legend:
R = Readable bit
W = Writable bit
U = Unimplemented bit, read as ‘0’
-n = Value at POR
‘1’ = Bit is set
‘0’ = Bit is cleared
x = Bit is unknown
bit 15
FRMEN: Framed SPIx Support bit
1 = Framed SPIx support enabled (SSx pin used as frame sync pulse input/output)
0 = Framed SPIx support disabled
bit 14
SPIFSD: Frame Sync Pulse Direction Control bit
1 = Frame sync pulse input (slave)
0 = Frame sync pulse output (master)
bit 13
FRMPOL: Frame Sync Pulse Polarity bit
1 = Frame sync pulse is active-high
0 = Frame sync pulse is active-low
bit 12-2
Unimplemented: Read as ‘0’
bit 1
FRMDLY: Frame Sync Pulse Edge Select bit
1 = Frame sync pulse coincides with first bit clock
0 = Frame sync pulse precedes first bit clock
bit 0
Unimplemented: Read as ‘0’
This bit must not be set to ‘1’ by the user application
 2009 Microchip Technology Inc.
Preliminary
DS70592B-page 165
PIC24HJXXXGPX06A/X08A/X10A
NOTES:
DS70592B-page 166
Preliminary
 2009 Microchip Technology Inc.
PIC24HJXXXGPX06A/X08A/X10A
17.0
INTER-INTEGRATED
CIRCUIT™ (I2C™)
17.1
Note 1: This data sheet summarizes the features
of the PIC24HJXXXGPX06A/X08A/X10A
family of devices. However, it is not
intended to be a comprehensive
reference source. To complement the
information in this data sheet, refer to
Section 19. “Inter-Integrated Circuit™
(I2C™)” (DS70235) of the “dsPIC33F/
PIC24H Family Reference Manual”,
which is available from the Microchip
website (www.microchip.com).
2: Some registers and associated bits
described in this section may not be available on all devices. Refer to Section 4.0
“Memory Organization” in this data
sheet for device-specific register and bit
information.
The Inter-Integrated Circuit (I2C) module provides
complete hardware support for both Slave and MultiMaster modes of the I2C serial communication
standard, with a 16-bit interface.
The PIC24HJXXXGPX06A/X08A/X10A devices have
up to two I2C interface modules, denoted as I2C1 and
I2C2. Each I2C module has a 2-pin interface: the SCLx
pin is clock and the SDAx pin is data.
Each I2C module ‘x’ (x = 1 or 2) offers the following key
features:
• I2C interface supporting both master and slave
operation.
• I2C Slave mode supports 7 and 10-bit address.
• I2C Master mode supports 7 and 10-bit address.
• I2C Port allows bidirectional transfers between
master and slaves.
• Serial clock synchronization for I2C port can be
used as a handshake mechanism to suspend and
resume serial transfer (SCLREL control).
• I2C supports multi-master operation; detects bus
collision and will arbitrate accordingly.
 2009 Microchip Technology Inc.
Operating Modes
The hardware fully implements all the master and slave
functions of the I2C Standard and Fast mode
specifications, as well as 7 and 10-bit addressing.
The I2C module can operate either as a slave or a
master on an I2C bus.
The following types of I2C operation are supported:
•
•
•
I2C slave operation with 7-bit address
I2C slave operation with 10-bit address
I2C master operation with 7 or 10-bit address
For details about the communication sequence in each
of these modes, please refer to the “dsPIC33F/PIC24H
Family Reference Manual”.
17.2
I2C Registers
I2CxCON and I2CxSTAT are control and status
registers, respectively. The I2CxCON register is
readable and writable. The lower six bits of I2CxSTAT
are read-only. The remaining bits of the I2CSTAT are
read/write.
I2CxRSR is the shift register used for shifting data,
whereas I2CxRCV is the buffer register to which data
bytes are written, or from which data bytes are read.
I2CxRCV is the receive buffer. I2CxTRN is the transmit
register to which bytes are written during a transmit
operation.
The I2CxADD register holds the slave address. A
status bit, ADD10, indicates 10-bit Address mode. The
I2CxBRG acts as the Baud Rate Generator (BRG)
reload value.
In receive operations, I2CxRSR and I2CxRCV together
form a double-buffered receiver. When I2CxRSR
receives a complete byte, it is transferred to I2CxRCV
and an interrupt pulse is generated.
Preliminary
DS70592B-page 167
PIC24HJXXXGPX06A/X08A/X10A
FIGURE 17-1:
I2C™ BLOCK DIAGRAM (X = 1 OR 2)
Internal
Data Bus
I2CxRCV
Read
SCLx
Shift
Clock
I2CxRSR
LSB
SDAx
Address Match
Match Detect
Write
I2CxMSK
Write
Read
I2CxADD
Read
Start and Stop
Bit Detect
Write
Start and Stop
Bit Generation
Control Logic
I2CxSTAT
Collision
Detect
Read
Write
I2CxCON
Acknowledge
Generation
Read
Clock
Stretching
Write
I2CxTRN
LSB
Read
Shift Clock
Reload
Control
Write
BRG Down Counter
I2CxBRG
Read
TCY/2
DS70592B-page 168
Preliminary
 2009 Microchip Technology Inc.
PIC24HJXXXGPX06A/X08A/X10A
REGISTER 17-1:
I2CxCON: I2Cx CONTROL REGISTER
R/W-0
U-0
R/W-0
R/W-1 HC
R/W-0
R/W-0
R/W-0
R/W-0
I2CEN
—
I2CSIDL
SCLREL
IPMIEN
A10M
DISSLW
SMEN
bit 15
bit 8
R/W-0
R/W-0
R/W-0
R/W-0 HC
R/W-0 HC
R/W-0 HC
R/W-0 HC
R/W-0 HC
GCEN
STREN
ACKDT
ACKEN
RCEN
PEN
RSEN
SEN
bit 7
bit 0
Legend:
U = Unimplemented bit, read as ‘0’
R = Readable bit
W = Writable bit
HS = Set in hardware
HC = Cleared in hardware
-n = Value at POR
‘1’ = Bit is set
‘0’ = Bit is cleared
x = Bit is unknown
bit 15
I2CEN: I2Cx Enable bit
1 = Enables the I2Cx module and configures the SDAx and SCLx pins as serial port pins
0 = Disables the I2Cx module. All I2C pins are controlled by port functions.
bit 14
Unimplemented: Read as ‘0’
bit 13
I2CSIDL: Stop in Idle Mode bit
1 = Discontinue module operation when device enters an Idle mode
0 = Continue module operation in Idle mode
bit 12
SCLREL: SCLx Release Control bit (when operating as I2C slave)
1 = Release SCLx clock
0 = Hold SCLx clock low (clock stretch)
If STREN = 1:
Bit is R/W (i.e., software may write ‘0’ to initiate stretch and write ‘1’ to release clock). Hardware clear
at beginning of slave transmission. Hardware clear at end of slave reception.
If STREN = 0:
Bit is R/S (i.e., software may only write ‘1’ to release clock). Hardware clear at beginning of slave
transmission.
bit 11
IPMIEN: Intelligent Peripheral Management Interface (IPMI) Enable bit
1 = IPMI mode is enabled; all addresses Acknowledged
0 = IPMI mode disabled
bit 10
A10M: 10-bit Slave Address bit
1 = I2CxADD is a 10-bit slave address
0 = I2CxADD is a 7-bit slave address
bit 9
DISSLW: Disable Slew Rate Control bit
1 = Slew rate control disabled
0 = Slew rate control enabled
bit 8
SMEN: SMBus Input Levels bit
1 = Enable I/O pin thresholds compliant with SMBus specification
0 = Disable SMBus input thresholds
bit 7
GCEN: General Call Enable bit (when operating as I2C slave)
1 = Enable interrupt when a general call address is received in the I2CxRSR
(module is enabled for reception)
0 = General call address disabled
bit 6
STREN: SCLx Clock Stretch Enable bit (when operating as I2C slave)
Used in conjunction with SCLREL bit.
1 = Enable software or receive clock stretching
0 = Disable software or receive clock stretching
 2009 Microchip Technology Inc.
Preliminary
DS70592B-page 169
PIC24HJXXXGPX06A/X08A/X10A
REGISTER 17-1:
I2CxCON: I2Cx CONTROL REGISTER (CONTINUED)
bit 5
ACKDT: Acknowledge Data bit (when operating as I2C master, applicable during master receive)
Value that will be transmitted when the software initiates an Acknowledge sequence.
1 = Send NACK during Acknowledge
0 = Send ACK during Acknowledge
bit 4
ACKEN: Acknowledge Sequence Enable bit
(when operating as I2C master, applicable during master receive)
1 = Initiate Acknowledge sequence on SDAx and SCLx pins and transmit ACKDT data bit.
Hardware clear at end of master Acknowledge sequence.
0 = Acknowledge sequence not in progress
bit 3
RCEN: Receive Enable bit (when operating as I2C master)
1 = Enables Receive mode for I2C. Hardware clear at end of eighth bit of master receive data byte.
0 = Receive sequence not in progress
bit 2
PEN: Stop Condition Enable bit (when operating as I2C master)
1 = Initiate Stop condition on SDAx and SCLx pins. Hardware clear at end of master Stop sequence.
0 = Stop condition not in progress
bit 1
RSEN: Repeated Start Condition Enable bit (when operating as I2C master)
1 = Initiate Repeated Start condition on SDAx and SCLx pins. Hardware clear at end of
master Repeated Start sequence.
0 = Repeated Start condition not in progress
bit 0
SEN: Start Condition Enable bit (when operating as I2C master)
1 = Initiate Start condition on SDAx and SCLx pins. Hardware clear at end of master Start sequence.
0 = Start condition not in progress
DS70592B-page 170
Preliminary
 2009 Microchip Technology Inc.
PIC24HJXXXGPX06A/X08A/X10A
REGISTER 17-2:
I2CxSTAT: I2Cx STATUS REGISTER
R-0 HSC
R-0 HSC
U-0
U-0
U-0
R/C-0 HS
R-0 HSC
R-0 HSC
ACKSTAT
TRSTAT
—
—
—
BCL
GCSTAT
ADD10
bit 15
bit 8
R/C-0 HS
R/C-0 HS
R-0 HSC
R/C-0 HSC
R/C-0 HSC
R-0 HSC
R-0 HSC
R-0 HSC
IWCOL
I2COV
D_A
P
S
R_W
RBF
TBF
bit 7
bit 0
Legend:
U = Unimplemented bit, read as ‘0’
C = Clear only bit
R = Readable bit
W = Writable bit
HS = Set in hardware
HSC = Hardware set/cleared
-n = Value at POR
‘1’ = Bit is set
‘0’ = Bit is cleared
x = Bit is unknown
bit 15
ACKSTAT: Acknowledge Status bit
(when operating as I2C master, applicable to master transmit operation)
1 = NACK received from slave
0 = ACK received from slave
Hardware set or clear at end of slave Acknowledge.
bit 14
TRSTAT: Transmit Status bit (when operating as I2C master, applicable to master transmit operation)
1 = Master transmit is in progress (8 bits + ACK)
0 = Master transmit is not in progress
Hardware set at beginning of master transmission. Hardware clear at end of slave Acknowledge.
bit 13-11
Unimplemented: Read as ‘0’
bit 10
BCL: Master Bus Collision Detect bit
1 = A bus collision has been detected during a master operation
0 = No collision
Hardware set at detection of bus collision.
bit 9
GCSTAT: General Call Status bit
1 = General call address was received
0 = General call address was not received
Hardware set when address matches general call address. Hardware clear at Stop detection.
bit 8
ADD10: 10-Bit Address Status bit
1 = 10-bit address was matched
0 = 10-bit address was not matched
Hardware set at match of 2nd byte of matched 10-bit address. Hardware clear at Stop detection.
bit 7
IWCOL: Write Collision Detect bit
1 = An attempt to write the I2CxTRN register failed because the I2C module is busy
0 = No collision
Hardware set at occurrence of write to I2CxTRN while busy (cleared by software).
bit 6
I2COV: Receive Overflow Flag bit
1 = A byte was received while the I2CxRCV register is still holding the previous byte
0 = No overflow
Hardware set at attempt to transfer I2CxRSR to I2CxRCV (cleared by software).
bit 5
D_A: Data/Address bit (when operating as I2C slave)
1 = Indicates that the last byte received was data
0 = Indicates that the last byte received was device address
Hardware clear at device address match. Hardware set by reception of slave byte.
bit 4
P: Stop bit
1 = Indicates that a Stop bit has been detected last
0 = Stop bit was not detected last
Hardware set or clear when Start, Repeated Start or Stop detected.
 2009 Microchip Technology Inc.
Preliminary
DS70592B-page 171
PIC24HJXXXGPX06A/X08A/X10A
REGISTER 17-2:
I2CxSTAT: I2Cx STATUS REGISTER (CONTINUED)
bit 3
S: Start bit
1 = Indicates that a Start (or Repeated Start) bit has been detected last
0 = Start bit was not detected last
Hardware set or clear when Start, Repeated Start or Stop detected.
bit 2
R_W: Read/Write Information bit (when operating as I2C slave)
1 = Read – indicates data transfer is output from slave
0 = Write – indicates data transfer is input to slave
Hardware set or clear after reception of I 2C device address byte.
bit 1
RBF: Receive Buffer Full Status bit
1 = Receive complete, I2CxRCV is full
0 = Receive not complete, I2CxRCV is empty
Hardware set when I2CxRCV is written with received byte. Hardware clear when software
reads I2CxRCV.
bit 0
TBF: Transmit Buffer Full Status bit
1 = Transmit in progress, I2CxTRN is full
0 = Transmit complete, I2CxTRN is empty
Hardware set when software writes I2CxTRN. Hardware clear at completion of data transmission.
DS70592B-page 172
Preliminary
 2009 Microchip Technology Inc.
PIC24HJXXXGPX06A/X08A/X10A
REGISTER 17-3:
I2CxMSK: I2Cx SLAVE MODE ADDRESS MASK REGISTER
U-0
U-0
U-0
U-0
U-0
U-0
R/W-0
R/W-0
—
—
—
—
—
—
AMSK9
AMSK8
bit 15
bit 8
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
AMSK7
AMSK6
AMSK5
AMSK4
AMSK3
AMSK2
AMSK1
AMSK0
bit 7
bit 0
Legend:
R = Readable bit
W = Writable bit
U = Unimplemented bit, read as ‘0’
-n = Value at POR
‘1’ = Bit is set
‘0’ = Bit is cleared
x = Bit is unknown
bit 15-10
Unimplemented: Read as ‘0’
bit 9-0
AMSKx: Mask for Address Bit x Select bit
1 = Enable masking for bit x of incoming message address; bit match not required in this position
0 = Disable masking for bit x; bit match required in this position
 2009 Microchip Technology Inc.
Preliminary
DS70592B-page 173
PIC24HJXXXGPX06A/X08A/X10A
NOTES:
DS70592B-page 174
Preliminary
 2009 Microchip Technology Inc.
PIC24HJXXXGPX06A/X08A/X10A
18.0
UNIVERSAL ASYNCHRONOUS
RECEIVER TRANSMITTER
(UART)
Note 1: This data sheet summarizes the features
of the PIC24HJXXXGPX06A/X08A/X10A
family of devices. However, it is not
intended to be a comprehensive reference source. To complement the information in this data sheet, refer to Section
17. “UART” (DS70232) of the
“dsPIC33F/PIC24H Family Reference
Manual”, which is available from the
Microchip website (www.microchip.com).
2: Some registers and associated bits
described in this section may not be available on all devices. Refer to Section 4.0
“Memory Organization” in this data
sheet for device-specific register and bit
information.
The Universal Asynchronous Receiver Transmitter
(UART) module is one of the serial I/O modules available in the PIC24HJXXXGPX06A/X08A/X10A device
family. The UART is a full-duplex asynchronous system
that can communicate with peripheral devices, such as
personal computers, LIN, RS-232 and RS-485 interfaces. The module also supports a hardware flow control option with the UxCTS and UxRTS pins and also
includes an IrDA® encoder and decoder.
The primary features of the UART module are:
FIGURE 18-1:
• Full-Duplex, 8 or 9-bit Data Transmission through
the UxTX and UxRX pins
• Even, Odd or No Parity Options (for 8-bit data)
• One or Two Stop bits
• Hardware Flow Control Option with UxCTS and
UxRTS pins
• Fully Integrated Baud Rate Generator with 16-bit
Prescaler
• Baud rates ranging from 10 Mbps to 38 bps at 40
MIPS
• 4-deep First-In-First-Out (FIFO) Transmit Data
Buffer
• 4-Deep FIFO Receive Data Buffer
• Parity, Framing and Buffer Overrun Error Detection
• Support for 9-bit mode with Address Detect
(9th bit = 1)
• Transmit and Receive Interrupts
• A Separate Interrupt for all UART Error Conditions
• Loopback mode for Diagnostic Support
• Support for Sync and Break Characters
• Supports Automatic Baud Rate Detection
• IrDA® Encoder and Decoder Logic
• 16x Baud Clock Output for IrDA® Support
A simplified block diagram of the UART is shown in
Figure 18-1. The UART module consists of the key
important hardware elements:
• Baud Rate Generator
• Asynchronous Transmitter
• Asynchronous Receiver
UART SIMPLIFIED BLOCK DIAGRAM
Baud Rate Generator
IrDA®
BCLK
Hardware Flow Control
UxRTS
UxCTS
UART Receiver
UxRX
UART Transmitter
UxTX
Note 1: Both UART1 and UART2 can trigger a DMA data transfer. If U1TX, U1RX, U2TX or U2RX is selected as
a DMA IRQ source, a DMA transfer occurs when the U1TXIF, U1RXIF, U2TXIF or U2RXIF bit gets set as
a result of a UART1 or UART2 transmission or reception.
2: If DMA transfers are required, the UART TX/RX FIFO buffer must be set to a size of 1 byte/word
(i.e., UTXISEL<1:0> = 00 and URXISEL<1:0> = 00).
 2009 Microchip Technology Inc.
Preliminary
DS70592B-page 175
PIC24HJXXXGPX06A/X08A/X10A
REGISTER 18-1:
UxMODE: UARTx MODE REGISTER
R/W-0
U-0
R/W-0
R/W-0
R/W-0
U-0
UARTEN(1)
—
USIDL
IREN(2)
RTSMD
—
R/W-0
R/W-0
UEN<1:0>
bit 15
bit 8
R/W-0 HC
R/W-0
R/W-0 HC
R/W-0
R/W-0
WAKE
LPBACK
ABAUD
URXINV
BRGH
R/W-0
R/W-0
PDSEL<1:0>
R/W-0
STSEL
bit 7
bit 0
Legend:
HC = Hardware cleared
R = Readable bit
W = Writable bit
U = Unimplemented bit, read as ‘0’
-n = Value at POR
‘1’ = Bit is set
‘0’ = Bit is cleared
x = Bit is unknown
bit 15
UARTEN: UARTx Enable bit(1)
1 = UARTx is enabled; all UARTx pins are controlled by UARTx as defined by UEN<1:0>
0 = UARTx is disabled; all UARTx pins are controlled by port latches; UARTx power consumption
minimal
bit 14
Unimplemented: Read as ‘0’
bit 13
USIDL: Stop in Idle Mode bit
1 = Discontinue module operation when device enters Idle mode
0 = Continue module operation in Idle mode
bit 12
IREN: IrDA® Encoder and Decoder Enable bit(2)
1 = IrDA® encoder and decoder enabled
0 = IrDA® encoder and decoder disabled
bit 11
RTSMD: Mode Selection for UxRTS Pin bit
1 = UxRTS pin in Simplex mode
0 = UxRTS pin in Flow Control mode
bit 10
Unimplemented: Read as ‘0’
bit 9-8
UEN<1:0>: UARTx Enable bits
11 = UxTX, UxRX and BCLK pins are enabled and used; UxCTS pin controlled by port latches
10 = UxTX, UxRX, UxCTS and UxRTS pins are enabled and used
01 = UxTX, UxRX and UxRTS pins are enabled and used; UxCTS pin controlled by port latches
00 = UxTX and UxRX pins are enabled and used; UxCTS and UxRTS/BCLK pins controlled by
port latches
bit 7
WAKE: Wake-up on Start bit Detect During Sleep Mode Enable bit
1 = UARTx will continue to sample the UxRX pin; interrupt generated on falling edge; bit cleared
in hardware on following rising edge
0 = No wake-up enabled
bit 6
LPBACK: UARTx Loopback Mode Select bit
1 = Enable Loopback mode
0 = Loopback mode is disabled
bit 5
ABAUD: Auto-Baud Enable bit
1 = Enable baud rate measurement on the next character – requires reception of a Sync field (0x55)
before any data; cleared in hardware upon completion
0 = Baud rate measurement disabled or completed
Note 1: Refer to Section 17. “UART” (DS70232) in the “dsPIC33F/PIC24H Family Reference Manual” for information on enabling the UART module for receive or transmit operation.
2: This feature is only available for the 16x BRG mode (BRGH = 0).
DS70592B-page 176
Preliminary
 2009 Microchip Technology Inc.
PIC24HJXXXGPX06A/X08A/X10A
REGISTER 18-1:
UxMODE: UARTx MODE REGISTER (CONTINUED)
bit 4
URXINV: Receive Polarity Inversion bit
1 = UxRX Idle state is ‘0’
0 = UxRX Idle state is ‘1’
bit 3
BRGH: High Baud Rate Enable bit
1 = BRG generates 4 clocks per bit period (4x baud clock, High-Speed mode)
0 = BRG generates 16 clocks per bit period (16x baud clock, Standard mode)
bit 2-1
PDSEL<1:0>: Parity and Data Selection bits
11 = 9-bit data, no parity
10 = 8-bit data, odd parity
01 = 8-bit data, even parity
00 = 8-bit data, no parity
bit 0
STSEL: Stop Bit Selection bit
1 = Two Stop bits
0 = One Stop bit
Note 1: Refer to Section 17. “UART” (DS70232) in the “dsPIC33F/PIC24H Family Reference Manual” for information on enabling the UART module for receive or transmit operation.
2: This feature is only available for the 16x BRG mode (BRGH = 0).
 2009 Microchip Technology Inc.
Preliminary
DS70592B-page 177
PIC24HJXXXGPX06A/X08A/X10A
REGISTER 18-2:
UxSTA: UARTx STATUS AND CONTROL REGISTER
R/W-0
R/W-0
R/W-0
U-0
R/W-0 HC
R/W-0
R-0
R-1
UTXISEL1
UTXINV
UTXISEL0
—
UTXBRK
UTXEN(1)
UTXBF
TRMT
bit 15
bit 8
R/W-0
R/W-0
URXISEL<1:0>
R/W-0
R-1
R-0
R-0
R/C-0
R-0
ADDEN
RIDLE
PERR
FERR
OERR
URXDA
bit 7
bit 0
Legend:
HC = Hardware cleared
R = Readable bit
W = Writable bit
U = Unimplemented bit, read as ‘0’
C = Clear only bit
-n = Value at POR
‘1’ = Bit is set
‘0’ = Bit is cleared
x = Bit is unknown
bit 15,13
UTXISEL<1:0>: Transmission Interrupt Mode Selection bits
11 = Reserved; do not use
10 = Interrupt when a character is transferred to the Transmit Shift Register, and as a result, the
transmit buffer becomes empty
01 = Interrupt when the last character is shifted out of the Transmit Shift Register; all transmit
operations are completed
00 = Interrupt when a character is transferred to the Transmit Shift Register (this implies there is
at least one character open in the transmit buffer)
bit 14
UTXINV: Transmit Polarity Inversion bit
If IREN = 0:
1 = UxTX Idle state is ‘0’
0 = UxTX Idle state is ‘1’
If IREN = 1:
1 = IrDA® encoded UxTX Idle state is ‘1’
0 = IrDA® encoded UxTX Idle state is ‘0’
bit 12
Unimplemented: Read as ‘0’
bit 11
UTXBRK: Transmit Break bit
1 = Send Sync Break on next transmission – Start bit, followed by twelve ‘0’ bits, followed by Stop bit;
cleared by hardware upon completion
0 = Sync Break transmission disabled or completed
bit 10
UTXEN: Transmit Enable bit(1)
1 = Transmit enabled, UxTX pin controlled by UARTx
0 = Transmit disabled, any pending transmission is aborted and buffer is reset. UxTX pin controlled
by port.
bit 9
UTXBF: Transmit Buffer Full Status bit (read-only)
1 = Transmit buffer is full
0 = Transmit buffer is not full, at least one more character can be written
bit 8
TRMT: Transmit Shift Register Empty bit (read-only)
1 = Transmit Shift Register is empty and transmit buffer is empty (the last transmission has completed)
0 = Transmit Shift Register is not empty, a transmission is in progress or queued
bit 7-6
URXISEL<1:0>: Receive Interrupt Mode Selection bits
11 = Interrupt is set on UxRSR transfer making the receive buffer full (i.e., has 4 data characters)
10 = Interrupt is set on UxRSR transfer making the receive buffer 3/4 full (i.e., has 3 data characters)
0x = Interrupt is set when any character is received and transferred from the UxRSR to the receive
buffer. Receive buffer has one or more characters.
Note 1: Refer to Section 17. “UART” (DS70232) in the “dsPIC33F/PIC24H Family Reference Manual” for information on enabling the UART module for transmit operation.
DS70592B-page 178
Preliminary
 2009 Microchip Technology Inc.
PIC24HJXXXGPX06A/X08A/X10A
REGISTER 18-2:
UxSTA: UARTx STATUS AND CONTROL REGISTER (CONTINUED)
bit 5
ADDEN: Address Character Detect bit (bit 8 of received data = 1)
1 = Address Detect mode enabled. If 9-bit mode is not selected, this does not take effect
0 = Address Detect mode disabled
bit 4
RIDLE: Receiver Idle bit (read-only)
1 = Receiver is Idle
0 = Receiver is active
bit 3
PERR: Parity Error Status bit (read-only)
1 = Parity error has been detected for the current character (character at the top of the receive FIFO)
0 = Parity error has not been detected
bit 2
FERR: Framing Error Status bit (read-only)
1 = Framing error has been detected for the current character (character at the top of the receive
FIFO)
0 = Framing error has not been detected
bit 1
OERR: Receive Buffer Overrun Error Status bit (read/clear only)
1 = Receive buffer has overflowed
0 = Receive buffer has not overflowed. Clearing a previously set OERR bit (1  0 transition) will reset
the receiver buffer and the UxRSR to the empty state
bit 0
URXDA: Receive Buffer Data Available bit (read-only)
1 = Receive buffer has data, at least one more character can be read
0 = Receive buffer is empty
Note 1: Refer to Section 17. “UART” (DS70232) in the “dsPIC33F/PIC24H Family Reference Manual” for information on enabling the UART module for transmit operation.
 2009 Microchip Technology Inc.
Preliminary
DS70592B-page 179
PIC24HJXXXGPX06A/X08A/X10A
NOTES:
DS70592B-page 180
Preliminary
 2009 Microchip Technology Inc.
PIC24HJXXXGPX06A/X08A/X10A
19.0
ENHANCED CAN (ECAN™)
MODULE
Note 1: This data sheet summarizes the features
of the PIC24HJXXXGPX06A/X08A/X10A
family of devices. However, it is not
intended to be a comprehensive reference source. To complement the information in this data sheet, refer to the
“dsPIC33F/PIC24H Family Reference
Manual”, Section 21. “Enhanced Controller Area Network (ECAN™)”
(DS70226), which is available from the
Microchip website (www.microchip.com).
2: Some registers and associated bits
described in this section may not be available on all devices. Refer to Section 4.0
“Memory Organization” in this data
sheet for device-specific register and bit
information.
19.1
Overview
The Enhanced Controller Area Network (ECAN™)
module is a serial interface, useful for communicating
with other CAN modules or microcontroller devices.
This interface/protocol was designed to allow communications
within
noisy
environments.
The
PIC24HJXXXGPX06A/X08A/X10A devices contain up
to two ECAN modules.
The CAN module is a communication controller implementing the CAN 2.0 A/B protocol, as defined in the
BOSCH specification. The module will support CAN 1.2,
CAN 2.0A, CAN 2.0B Passive and CAN 2.0B Active
versions of the protocol. The module implementation is
a full CAN system. The CAN specification is not covered
within this data sheet. The reader may refer to the
BOSCH CAN specification for further details.
The module features are as follows:
• Implementation of the CAN protocol, CAN 1.2,
CAN 2.0A and CAN 2.0B
• Standard and extended data frames
• 0-8 bytes data length
• Programmable bit rate up to 1 Mbit/sec
• Automatic response to remote transmission
requests
• Up to 8 transmit buffers with application specified
prioritization and abort capability (each buffer may
contain up to 8 bytes of data)
• Up to 32 receive buffers (each buffer may contain
up to 8 bytes of data)
• Up to 16 full (standard/extended identifier)
acceptance filters
• 3 full acceptance filter masks
• DeviceNet™ addressing support
• Programmable wake-up functionality with
integrated low-pass filter
• Programmable Loopback mode supports self-test
operation
 2009 Microchip Technology Inc.
• Signaling via interrupt capabilities for all CAN
receiver and transmitter error states
• Programmable clock source
• Programmable link to input capture module (IC2
for both CAN1 and CAN2) for time-stamping and
network synchronization
• Low-power Sleep and Idle mode
The CAN bus module consists of a protocol engine and
message buffering/control. The CAN protocol engine
handles all functions for receiving and transmitting
messages on the CAN bus. Messages are transmitted
by first loading the appropriate data registers. Status
and errors can be checked by reading the appropriate
registers. Any message detected on the CAN bus is
checked for errors and then matched against filters to
see if it should be received and stored in one of the
receive registers.
19.2
Frame Types
The CAN module transmits various types of frames
which include data messages, remote transmission
requests and as other frames that are automatically
generated for control purposes. The following frame
types are supported:
• Standard Data Frame:
A standard data frame is generated by a node when
the node wishes to transmit data. It includes an 11-bit
standard identifier (SID) but not an 18-bit extended
identifier (EID).
• Extended Data Frame:
An extended data frame is similar to a standard data
frame but includes an extended identifier as well.
• Remote Frame:
It is possible for a destination node to request the
data from the source. For this purpose, the
destination node sends a remote frame with an identifier that matches the identifier of the required data
frame. The appropriate data source node will then
send a data frame as a response to this remote
request.
• Error Frame:
An error frame is generated by any node that detects
a bus error. An error frame consists of two fields: an
error flag field and an error delimiter field.
• Overload Frame:
An overload frame can be generated by a node as a
result of two conditions. First, the node detects a
dominant bit during interframe space which is an illegal condition. Second, due to internal conditions, the
node is not yet able to start reception of the next
message. A node may generate a maximum of 2
sequential overload frames to delay the start of the
next message.
• Interframe Space:
Interframe space separates a proceeding frame (of
whatever type) from a following data or remote
frame.
Preliminary
DS70592B-page 181
PIC24HJXXXGPX06A/X08A/X10A
FIGURE 19-1:
ECAN™ MODULE BLOCK DIAGRAM
RXF15 Filter
RXF14 Filter
RXF13 Filter
RXF12 Filter
DMA Controller
RXF11 Filter
RXF10 Filter
RXF9 Filter
RXF8 Filter
TRB7 TX/RX Buffer Control Register
RXF7 Filter
TRB6 TX/RX Buffer Control Register
RXF6 Filter
TRB5 TX/RX Buffer Control Register
RXF5 Filter
TRB4 TX/RX Buffer Control Register
RXF4 Filter
TRB3 TX/RX Buffer Control Register
RXF3 Filter
TRB2 TX/RX Buffer Control Register
RXF2 Filter
RXM2 Mask
TRB1 TX/RX Buffer Control Register
RXF1 Filter
RXM1 Mask
TRB0 TX/RX Buffer Control Register
RXF0 Filter
RXM0 Mask
Transmit Byte
Sequencer
Message Assembly
Buffer
Control
Configuration
Logic
CPU
Bus
CAN Protocol
Engine
Interrupts
CiTX(1)
CiRX(1)
Note 1: i = 1 or 2 refers to a particular ECAN™ module (ECAN1 or ECAN2).
DS70592B-page 182
Preliminary
 2009 Microchip Technology Inc.
PIC24HJXXXGPX06A/X08A/X10A
19.3
Modes of Operation
Note:
The CAN module can operate in one of several operation
modes selected by the user. These modes include:
•
•
•
•
•
•
Initialization Mode
Disable Mode
Normal Operation Mode
Listen Only Mode
Listen All Messages Mode
Loopback Mode
Modes are requested by setting the REQOP<2:0> bits
(CiCTRL1<10:8>). Entry into a mode is Acknowledged
by
monitoring
the
OPMODE<2:0>
bits
(CiCTRL1<7:5>). The module will not change the mode
and the OPMODE bits until a change in mode is
acceptable, generally during bus Idle time, which is
defined as at least 11 consecutive recessive bits.
19.3.1
INITIALIZATION MODE
All Module Control Registers
Baud Rate and Interrupt Configuration Registers
Bus Timing Registers
Identifier Acceptance Filter Registers
Identifier Acceptance Mask Registers
19.3.2
DISABLE MODE
LISTEN ONLY MODE
If the Listen Only mode is activated, the module on the
CAN bus is passive. The transmitter buffers revert to
the port I/O function. The receive pins remain inputs.
For the receiver, no error flags or Acknowledge signals
are sent. The error counters are deactivated in this
state. The Listen Only mode can be used for detecting
the baud rate on the CAN bus. To use this, it is necessary that there are at least two further nodes that
communicate with each other.
19.3.5
LISTEN ALL MESSAGES MODE
The module can be set to ignore all errors and receive
any message. The Listen All Messages mode is activated by setting REQOP<2:0> = ‘111’. In this mode,
the data which is in the message assembly buffer, until
the time an error occurred, is copied in the receive buffer and can be read via the CPU interface.
19.3.6
In Disable mode, the module will not transmit or
receive. The module has the ability to set the WAKIF bit
due to bus activity, however, any pending interrupts will
remain and the error counters will retain their value.
NORMAL OPERATION MODE
Normal Operation mode is selected when
REQOP<2:0> = 000. In this mode, the module is
activated and the I/O pins will assume the CAN bus
functions. The module will transmit and receive CAN
bus messages via the CiTX and CiRX pins.
19.3.4
In the Initialization mode, the module will not transmit or
receive. The error counters are cleared and the interrupt flags remain unchanged. The programmer will
have access to Configuration registers that are access
restricted in other modes. The module will protect the
user from accidentally violating the CAN protocol
through programming errors. All registers which control
the configuration of the module can not be modified
while the module is on-line. The CAN module will not
be allowed to enter the Configuration mode while a
transmission is taking place. The Configuration mode
serves as a lock to protect the following registers.
•
•
•
•
•
19.3.3
Typically, if the CAN module is allowed to
transmit in a particular mode of operation
and a transmission is requested immediately after the CAN module has been
placed in that mode of operation, the module waits for 11 consecutive recessive bits
on the bus before starting transmission. If
the user switches to Disable mode within
this 11-bit period, then this transmission is
aborted and the corresponding TXABT bit
is set and TXREQ bit is cleared.
LOOPBACK MODE
If the Loopback mode is activated, the module will connect the internal transmit signal to the internal receive
signal at the module boundary. The transmit and
receive pins revert to their port I/O function.
If the REQOP<2:0> bits (CiCTRL1<10:8>) = 001, the
module will enter the Module Disable mode. If the module
is active, the module will wait for 11 recessive bits on the
CAN bus, detect that condition as an Idle bus, then
accept the module disable command. When the
OPMODE<2:0> bits (CiCTRL1<7:5>) = 001, that indicates whether the module successfully went into Module
Disable mode. The I/O pins will revert to normal I/O
function when the module is in the Module Disable mode.
The module can be programmed to apply a low-pass
filter function to the CiRX input line while the module or
the CPU is in Sleep mode. The WAKFIL bit
(CiCFG2<14>) enables or disables the filter.
 2009 Microchip Technology Inc.
Preliminary
DS70592B-page 183
PIC24HJXXXGPX06A/X08A/X10A
REGISTER 19-1:
CiCTRL1: ECAN™ MODULE CONTROL REGISTER 1
U-0
U-0
R/W-0
R/W-0
r-0
—
—
CSIDL
ABAT
—
R/W-1
R/W-0
R/W-0
REQOP<2:0>
bit 15
bit 8
R-1
R-0
R-0
OPMODE<2:0>
U-0
R/W-0
U-0
U-0
R/W-0
—
CANCAP
—
—
WIN
bit 7
bit 0
Legend:
r = Bit is Reserved
R = Readable bit
W = Writable bit
U = Unimplemented bit, read as ‘0’
-n = Value at POR
‘1’ = Bit is set
‘0’ = Bit is cleared
x = Bit is unknown
bit 15-14
Unimplemented: Read as ‘0’
bit 13
CSIDL: Stop in Idle Mode bit
1 = Discontinue module operation when device enters Idle mode
0 = Continue module operation in Idle mode
bit 12
ABAT: Abort All Pending Transmissions bit
Signal all transmit buffers to abort transmission. Module will clear this bit when all transmissions
are aborted.
bit 11
Reserved: Do not use
bit 10-8
REQOP<2:0>: Request Operation Mode bits
000 = Set Normal Operation mode
001 = Set Disable mode
010 = Set Loopback mode
011 = Set Listen Only Mode
100 = Set Configuration mode
101 = Reserved – do not use
110 = Reserved – do not use
111 = Set Listen All Messages mode
bit 7-5
OPMODE<2:0>: Operation Mode bits
000 = Module is in Normal Operation mode
001 = Module is in Disable mode
010 = Module is in Loopback mode
011 = Module is in Listen Only mode
100 = Module is in Configuration mode
101 = Reserved
110 = Reserved
111 = Module is in Listen All Messages mode
bit 4
Unimplemented: Read as ‘0’
bit 3
CANCAP: CAN Message Receive Timer Capture Event Enable bit
1 = Enable input capture based on CAN message receive
0 = Disable CAN capture
bit 2-1
Unimplemented: Read as ‘0’
bit 0
WIN: SFR Map Window Select bit
1 = Use filter window
0 = Use buffer window
DS70592B-page 184
Preliminary
 2009 Microchip Technology Inc.
PIC24HJXXXGPX06A/X08A/X10A
REGISTER 19-2:
CiCTRL2: ECAN™ MODULE CONTROL REGISTER 2
U-0
U-0
U-0
U-0
U-0
U-0
U-0
U-0
—
—
—
—
—
—
—
—
bit 15
bit 8
U-0
U-0
U-0
—
—
—
R-0
R-0
R-0
R-0
R-0
DNCNT<4:0>
bit 7
bit 0
Legend:
R = Readable bit
W = Writable bit
U = Unimplemented bit, read as ‘0’
-n = Value at POR
‘1’ = Bit is set
‘0’ = Bit is cleared
bit 15-5
Unimplemented: Read as ‘0’
bit 4-0
DNCNT<4:0>: DeviceNet™ Filter Bit Number bits
10010-11111 = Invalid selection
10001 = Compare up to data byte 3, bit 6 with EID<17>
•
•
•
00001 = Compare up to data byte 1, bit 7 with EID<0>
00000 = Do not compare data bytes
 2009 Microchip Technology Inc.
Preliminary
x = Bit is unknown
DS70592B-page 185
PIC24HJXXXGPX06A/X08A/X10A
REGISTER 19-3:
CiVEC: ECAN™ MODULE INTERRUPT CODE REGISTER
U-0
U-0
U-0
—
—
—
R-0
R-0
R-0
R-0
R-0
FILHIT<4:0>
bit 15
bit 8
U-0
R-1
R-0
R-0
—
R-0
R-0
R-0
R-0
ICODE<6:0>
bit 7
bit 0
Legend:
R = Readable bit
W = Writable bit
U = Unimplemented bit, read as ‘0’
-n = Value at POR
‘1’ = Bit is set
‘0’ = Bit is cleared
bit 15-13
Unimplemented: Read as ‘0’
bit 12-8
FILHIT<4:0>: Filter Hit Number bits
10000-11111 = Reserved
01111 = Filter 15
•
•
•
00001 = Filter 1
00000 = Filter 0
bit 7
Unimplemented: Read as ‘0’
bit 6-0
ICODE<6:0>: Interrupt Flag Code bits
1000101-1111111 = Reserved
1000100 = FIFO almost full interrupt
1000011 = Receiver overflow interrupt
1000010 = Wake-up interrupt
1000001 = Error interrupt
1000000 = No interrupt
x = Bit is unknown
0010000-0111111 = Reserved
0001111 = RB15 buffer Interrupt
•
•
•
0001001 = RB9 buffer interrupt
0001000 = RB8 buffer interrupt
0000111 = TRB7 buffer interrupt
0000110 = TRB6 buffer interrupt
0000101 = TRB5 buffer interrupt
0000100 = TRB4 buffer interrupt
0000011 = TRB3 buffer interrupt
0000010 = TRB2 buffer interrupt
0000001 = TRB1 buffer interrupt
0000000 = TRB0 Buffer interrupt
DS70592B-page 186
Preliminary
 2009 Microchip Technology Inc.
PIC24HJXXXGPX06A/X08A/X10A
REGISTER 19-4:
R/W-0
CiFCTRL: ECAN™ MODULE FIFO CONTROL REGISTER
R/W-0
R/W-0
DMABS<2:0>
U-0
U-0
U-0
U-0
U-0
—
—
—
—
—
bit 15
bit 8
U-0
U-0
U-0
—
—
—
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
FSA<4:0>
bit 7
bit 0
Legend:
R = Readable bit
W = Writable bit
U = Unimplemented bit, read as ‘0’
-n = Value at POR
‘1’ = Bit is set
‘0’ = Bit is cleared
bit 15-13
DMABS<2:0>: DMA Buffer Size bits
111 = Reserved
110 = 32 buffers in DMA RAM
101 = 24 buffers in DMA RAM
100 = 16 buffers in DMA RAM
011 = 12 buffers in DMA RAM
010 = 8 buffers in DMA RAM
001 = 6 buffers in DMA RAM
000 = 4 buffers in DMA RAM
bit 12-5
Unimplemented: Read as ‘0’
bit 4-0
FSA<4:0>: FIFO Area Starts with Buffer bits
11111 = RB31 buffer
11110 = RB30 buffer
•
•
•
00001 = TRB1 buffer
00000 = TRB0 buffer
 2009 Microchip Technology Inc.
Preliminary
x = Bit is unknown
DS70592B-page 187
PIC24HJXXXGPX06A/X08A/X10A
REGISTER 19-5:
CiFIFO: ECAN™ MODULE FIFO STATUS REGISTER
U-0
U-0
—
—
R-0
R-0
R-0
R-0
R-0
R-0
FBP<5:0>
bit 15
bit 8
U-0
U-0
—
—
R-0
R-0
R-0
R-0
R-0
R-0
FNRB<5:0>
bit 7
bit 0
Legend:
R = Readable bit
W = Writable bit
U = Unimplemented bit, read as ‘0’
-n = Value at POR
‘1’ = Bit is set
‘0’ = Bit is cleared
bit 15-14
Unimplemented: Read as ‘0’
bit 13-8
FBP<5:0>: FIFO Write Buffer Pointer bits
011111 = RB31 buffer
011110 = RB30 buffer
•
•
•
000001 = TRB1 buffer
000000 = TRB0 buffer
bit 7-6
Unimplemented: Read as ‘0’
bit 5-0
FNRB<5:0>: FIFO Next Read Buffer Pointer bits
011111 = RB31 buffer
011110 = RB30 buffer
•
•
•
000001 = TRB1 buffer
000000 = TRB0 buffer
DS70592B-page 188
Preliminary
x = Bit is unknown
 2009 Microchip Technology Inc.
PIC24HJXXXGPX06A/X08A/X10A
REGISTER 19-6:
CiINTF: ECAN™ MODULE INTERRUPT FLAG REGISTER
U-0
U-0
R-0
R-0
R-0
R-0
R-0
R-0
—
—
TXBO
TXBP
RXBP
TXWAR
RXWAR
EWARN
bit 15
bit 8
R/C-0
R/C-0
R/C-0
U-0
R/C-0
R/C-0
R/C-0
R/C-0
IVRIF
WAKIF
ERRIF
—
FIFOIF
RBOVIF
RBIF
TBIF
bit 7
bit 0
Legend:
C = Clear only bit
R = Readable bit
W = Writable bit
U = Unimplemented bit, read as ‘0’
-n = Value at POR
‘1’ = Bit is set
‘0’ = Bit is cleared
x = Bit is unknown
bit 15-14
Unimplemented: Read as ‘0’
bit 13
TXBO: Transmitter in Error State Bus Off bit
bit 12
TXBP: Transmitter in Error State Bus Passive bit
bit 11
RXBP: Receiver in Error State Bus Passive bit
bit 10
TXWAR: Transmitter in Error State Warning bit
bit 9
RXWAR: Receiver in Error State Warning bit
bit 8
EWARN: Transmitter or Receiver in Error State Warning bit
bit 7
IVRIF: Invalid Message Received Interrupt Flag bit
bit 6
WAKIF: Bus Wake-up Activity Interrupt Flag bit
bit 5
ERRIF: Error Interrupt Flag bit (multiple sources in CiINTF<13:8> register)
bit 4
Unimplemented: Read as ‘0’
bit 3
FIFOIF: FIFO Almost Full Interrupt Flag bit
bit 2
RBOVIF: RX Buffer Overflow Interrupt Flag bit
bit 1
RBIF: RX Buffer Interrupt Flag bit
bit 0
TBIF: TX Buffer Interrupt Flag bit
 2009 Microchip Technology Inc.
Preliminary
DS70592B-page 189
PIC24HJXXXGPX06A/X08A/X10A
REGISTER 19-7:
CiINTE: ECAN™ MODULE INTERRUPT ENABLE REGISTER
U-0
U-0
U-0
U-0
U-0
U-0
U-0
U-0
—
—
—
—
—
—
—
—
bit 15
bit 8
R/W-0
R/W-0
R/W-0
U-0
R/W-0
R/W-0
R/W-0
R/W-0
IVRIE
WAKIE
ERRIE
—
FIFOIE
RBOVIE
RBIE
TBIE
bit 7
bit 0
Legend:
R = Readable bit
W = Writable bit
U = Unimplemented bit, read as ‘0’
-n = Value at POR
‘1’ = Bit is set
‘0’ = Bit is cleared
bit 15-8
Unimplemented: Read as ‘0’
bit 7
IVRIE: Invalid Message Received Interrupt Enable bit
bit 6
WAKIE: Bus Wake-up Activity Interrupt Flag bit
bit 5
ERRIE: Error Interrupt Enable bit
bit 4
Unimplemented: Read as ‘0’
bit 3
FIFOIE: FIFO Almost Full Interrupt Enable bit
bit 2
RBOVIE: RX Buffer Overflow Interrupt Enable bit
bit 1
RBIE: RX Buffer Interrupt Enable bit
bit 0
TBIE: TX Buffer Interrupt Enable bit
DS70592B-page 190
Preliminary
x = Bit is unknown
 2009 Microchip Technology Inc.
PIC24HJXXXGPX06A/X08A/X10A
REGISTER 19-8:
R-0
CiEC: ECAN™ MODULE TRANSMIT/RECEIVE ERROR COUNT REGISTER
R-0
R-0
R-0
R-0
R-0
R-0
R-0
TERRCNT<7:0>
bit 15
bit 8
R-0
R-0
R-0
R-0
R-0
R-0
R-0
R-0
RERRCNT<7:0>
bit 7
bit 0
Legend:
R = Readable bit
W = Writable bit
U = Unimplemented bit, read as ‘0’
-n = Value at POR
‘1’ = Bit is set
‘0’ = Bit is cleared
bit 15-8
TERRCNT<7:0>: Transmit Error Count bits
bit 7-0
RERRCNT<7:0>: Receive Error Count bits
 2009 Microchip Technology Inc.
Preliminary
x = Bit is unknown
DS70592B-page 191
PIC24HJXXXGPX06A/X08A/X10A
REGISTER 19-9:
CiCFG1: ECAN™ MODULE BAUD RATE CONFIGURATION REGISTER 1
U-0
U-0
U-0
U-0
U-0
U-0
U-0
U-0
—
—
—
—
—
—
—
—
bit 15
bit 8
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
SJW<1:0>
R/W-0
R/W-0
R/W-0
BRP<5:0>
bit 7
bit 0
Legend:
R = Readable bit
W = Writable bit
U = Unimplemented bit, read as ‘0’
-n = Value at POR
‘1’ = Bit is set
‘0’ = Bit is cleared
bit 15-8
Unimplemented: Read as ‘0’
bit 7-6
SJW<1:0>: Synchronization Jump Width bits
11 = Length is 4 x TQ
10 = Length is 3 x TQ
01 = Length is 2 x TQ
00 = Length is 1 x TQ
bit 5-0
BRP<5:0>: Baud Rate Prescaler bits
11 1111 = TQ = 2 x 64 x 1/FCAN
•
•
•
00 0010 = TQ = 2 x 3 x 1/FCAN
00 0001 = TQ = 2 x 2 x 1/FCAN
00 0000 = TQ = 2 x 1 x 1/FCAN
DS70592B-page 192
Preliminary
x = Bit is unknown
 2009 Microchip Technology Inc.
PIC24HJXXXGPX06A/X08A/X10A
REGISTER 19-10: CiCFG2: ECAN™ MODULE BAUD RATE CONFIGURATION REGISTER 2
U-0
R/W-x
U-0
U-0
U-0
—
WAKFIL
—
—
—
R/W-x
R/W-x
R/W-x
SEG2PH<2:0>
bit 15
bit 8
R/W-x
R/W-x
SEG2PHTS
SAM
R/W-x
R/W-x
R/W-x
SEG1PH<2:0>
R/W-x
R/W-x
R/W-x
PRSEG<2:0>
bit 7
bit 0
Legend:
R = Readable bit
W = Writable bit
U = Unimplemented bit, read as ‘0’
-n = Value at POR
‘1’ = Bit is set
‘0’ = Bit is cleared
x = Bit is unknown
bit 15
Unimplemented: Read as ‘0’
bit 14
WAKFIL: Select CAN bus Line Filter for Wake-up bit
1 = Use CAN bus line filter for wake-up
0 = CAN bus line filter is not used for wake-up
bit 13-11
Unimplemented: Read as ‘0’
bit 10-8
SEG2PH<2:0>: Phase Buffer Segment 2 bits
111 = Length is 8 x TQ
000 = Length is 1 x TQ
bit 7
SEG2PHTS: Phase Segment 2 Time Select bit
1 = Freely programmable
0 = Maximum of SEG1PH bits or Information Processing Time (IPT), whichever is greater
bit 6
SAM: Sample of the CAN bus Line bit
1 = Bus line is sampled three times at the sample point
0 = Bus line is sampled once at the sample point
bit 5-3
SEG1PH<2:0>: Phase Buffer Segment 1 bits
111 = Length is 8 x TQ
000 = Length is 1 x TQ
bit 2-0
PRSEG<2:0>: Propagation Time Segment bits
111 = Length is 8 x TQ
000 = Length is 1 x TQ
 2009 Microchip Technology Inc.
Preliminary
DS70592B-page 193
PIC24HJXXXGPX06A/X08A/X10A
REGISTER 19-11: CiFEN1: ECAN™ MODULE ACCEPTANCE FILTER ENABLE REGISTER
R/W-1
R/W-1
R/W-1
R/W-1
R/W-1
R/W-1
R/W-1
R/W-1
FLTEN15
FLTEN14
FLTEN13
FLTEN12
FLTEN11
FLTEN10
FLTEN9
FLTEN8
bit 15
bit 8
R/W-1
R/W-1
R/W-1
R/W-1
R/W-1
R/W-1
R/W-1
R/W-1
FLTEN7
FLTEN6
FLTEN5
FLTEN4
FLTEN3
FLTEN2
FLTEN1
FLTEN0
bit 7
bit 0
Legend:
R = Readable bit
W = Writable bit
U = Unimplemented bit, read as ‘0’
-n = Value at POR
‘1’ = Bit is set
‘0’ = Bit is cleared
bit 15-0
x = Bit is unknown
FLTENn: Enable Filter n to Accept Messages bits
1 = Enable Filter n
0 = Disable Filter n
REGISTER 19-12: CiBUFPNT1: ECAN™ MODULE FILTER 0-3 BUFFER POINTER REGISTER
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
F3BP<3:0>
R/W-0
R/W-0
R/W-0
F2BP<3:0>
bit 15
bit 8
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
F1BP<3:0>
R/W-0
R/W-0
R/W-0
F0BP<3:0>
bit 7
bit 0
Legend:
R = Readable bit
W = Writable bit
U = Unimplemented bit, read as ‘0’
-n = Value at POR
‘1’ = Bit is set
‘0’ = Bit is cleared
bit 15-12
F3BP<3:0>: RX Buffer Written when Filter 3 Hits bits
bit 11-8
F2BP<3:0>: RX Buffer Written when Filter 2 Hits bits
bit 7-4
F1BP<3:0>: RX Buffer Written when Filter 1 Hits bits
bit 3-0
F0BP<3:0>: RX Buffer Written when Filter 0 Hits bits
1111 = Filter hits received in RX FIFO buffer
1110 = Filter hits received in RX Buffer 14
•
•
•
0001 = Filter hits received in RX Buffer 1
0000 = Filter hits received in RX Buffer 0
DS70592B-page 194
Preliminary
x = Bit is unknown
 2009 Microchip Technology Inc.
PIC24HJXXXGPX06A/X08A/X10A
REGISTER 19-13: CiBUFPNT2: ECAN™ MODULE FILTER 4-7 BUFFER POINTER REGISTER
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
F7BP<3:0>
R/W-0
R/W-0
R/W-0
F6BP<3:0>
bit 15
bit 8
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
F5BP<3:0>
R/W-0
R/W-0
R/W-0
F4BP<3:0>
bit 7
bit 0
Legend:
R = Readable bit
W = Writable bit
U = Unimplemented bit, read as ‘0’
-n = Value at POR
‘1’ = Bit is set
‘0’ = Bit is cleared
bit 15-12
F7BP<3:0>: RX Buffer Written when Filter 7 Hits bits
bit 11-8
F6BP<3:0>: RX Buffer Written when Filter 6 Hits bits
bit 7-4
F5BP<3:0>: RX Buffer Written when Filter 5 Hits bits
bit 3-0
F4BP<3:0>: RX Buffer Written when Filter 4 Hits bits
x = Bit is unknown
REGISTER 19-14: CiBUFPNT3: ECAN™ MODULE FILTER 8-11 BUFFER POINTER REGISTER
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
F11BP<3:0>
R/W-0
R/W-0
R/W-0
F10BP<3:0>
bit 15
bit 8
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
F9BP<3:0>
R/W-0
R/W-0
R/W-0
F8BP<3:0>
bit 7
bit 0
Legend:
R = Readable bit
W = Writable bit
U = Unimplemented bit, read as ‘0’
-n = Value at POR
‘1’ = Bit is set
‘0’ = Bit is cleared
bit 15-12
F11BP<3:0>: RX Buffer Written when Filter 11 Hits bits
bit 11-8
F10BP<3:0>: RX Buffer Written when Filter 10 Hits bits
bit 7-4
F9BP<3:0>: RX Buffer Written when Filter 9 Hits bits
bit 3-0
F8BP<3:0>: RX Buffer Written when Filter 8 Hits bits
 2009 Microchip Technology Inc.
Preliminary
x = Bit is unknown
DS70592B-page 195
PIC24HJXXXGPX06A/X08A/X10A
REGISTER 19-15: CiBUFPNT4: ECAN™ MODULE FILTER 12-15 BUFFER POINTER REGISTER
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
F15BP<3:0>
R/W-0
R/W-0
R/W-0
F14BP<3:0>
bit 15
bit 8
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
F13BP<3:0>
R/W-0
R/W-0
R/W-0
F12BP<3:0>
bit 7
bit 0
Legend:
R = Readable bit
W = Writable bit
U = Unimplemented bit, read as ‘0’
-n = Value at POR
‘1’ = Bit is set
‘0’ = Bit is cleared
bit 15-12
F15BP<3:0>: RX Buffer Written when Filter 15 Hits bits
bit 11-8
F14BP<3:0>: RX Buffer Written when Filter 14 Hits bits
bit 7-4
F13BP<3:0>: RX Buffer Written when Filter 13 Hits bits
bit 3-0
F12BP<3:0>: RX Buffer Written when Filter 12 Hits bits
DS70592B-page 196
Preliminary
x = Bit is unknown
 2009 Microchip Technology Inc.
PIC24HJXXXGPX06A/X08A/X10A
REGISTER 19-16:
CiRXFnSID: ECAN™ MODULE ACCEPTANCE FILTER n STANDARD IDENTIFIER
(n = 0, 1, ..., 15)
R/W-x
R/W-x
R/W-x
R/W-x
R/W-x
R/W-x
R/W-x
R/W-x
SID10
SID9
SID8
SID7
SID6
SID5
SID4
SID3
bit 15
bit 8
R/W-x
R/W-x
R/W-x
U-0
R/W-x
U-0
R/W-x
R/W-x
SID2
SID1
SID0
—
EXIDE
—
EID17
EID16
bit 7
bit 0
Legend:
R = Readable bit
W = Writable bit
U = Unimplemented bit, read as ‘0’
-n = Value at POR
‘1’ = Bit is set
‘0’ = Bit is cleared
bit 15-5
SID<10:0>: Standard Identifier bits
1 = Message address bit SIDx must be ‘1’ to match filter
0 = Message address bit SIDx must be ‘0’ to match filter
bit 4
Unimplemented: Read as ‘0’
bit 3
EXIDE: Extended Identifier Enable bit
If MIDE = 1 then:
1 = Match only messages with extended identifier addresses
0 = Match only messages with standard identifier addresses
If MIDE = 0 then:
Ignore EXIDE bit.
bit 2
Unimplemented: Read as ‘0’
bit 1-0
EID<17:16>: Extended Identifier bits
1 = Message address bit EIDx must be ‘1’ to match filter
0 = Message address bit EIDx must be ‘0’ to match filter
REGISTER 19-17:
x = Bit is unknown
CiRXFnEID: ECAN™ MODULE ACCEPTANCE FILTER n EXTENDED IDENTIFIER
(n = 0, 1, ..., 15)
R/W-x
R/W-x
R/W-x
R/W-x
R/W-x
R/W-x
R/W-x
R/W-x
EID15
EID14
EID13
EID12
EID11
EID10
EID9
EID8
bit 15
bit 8
R/W-x
R/W-x
R/W-x
R/W-x
R/W-x
R/W-x
R/W-x
R/W-x
EID7
EID6
EID5
EID4
EID3
EID2
EID1
EID0
bit 7
bit 0
Legend:
R = Readable bit
W = Writable bit
U = Unimplemented bit, read as ‘0’
-n = Value at POR
‘1’ = Bit is set
‘0’ = Bit is cleared
bit 15-0
x = Bit is unknown
EID<15:0>: Extended Identifier bits
1 = Message address bit EIDx must be ‘1’ to match filter
0 = Message address bit EIDx must be ‘0’ to match filter
 2009 Microchip Technology Inc.
Preliminary
DS70592B-page 197
PIC24HJXXXGPX06A/X08A/X10A
REGISTER 19-18: CiFMSKSEL1: ECAN™ MODULE FILTER 7-0 MASK SELECTION REGISTER
R/W-0
R/W-0
F7MSK<1:0>
R/W-0
R/W-0
R/W-0
F6MSK<1:0>
R/W-0
R/W-0
F5MSK<1:0>
R/W-0
F4MSK<1:0>
bit 15
bit 8
R/W-0
R/W-0
F3MSK<1:0>
R/W-0
R/W-0
R/W-0
F2MSK<1:0>
R/W-0
R/W-0
F1MSK<1:0>
R/W-0
F0MSK<1:0>
bit 7
bit 0
Legend:
R = Readable bit
W = Writable bit
U = Unimplemented bit, read as ‘0’
-n = Value at POR
‘1’ = Bit is set
‘0’ = Bit is cleared
bit 15-14
F7MSK<1:0>: Mask Source for Filter 7 bit
bit 13-12
F6MSK<1:0>: Mask Source for Filter 6 bit
bit 11-10
F5MSK<1:0>: Mask Source for Filter 5 bit
bit 9-8
F4MSK<1:0>: Mask Source for Filter 4 bit
bit 7-6
F3MSK<1:0>: Mask Source for Filter 3 bit
bit 5-4
F2MSK<1:0>: Mask Source for Filter 2 bit
bit 3-2
F1MSK<1:0>: Mask Source for Filter 1 bit
bit 1-0
F0MSK<1:0>: Mask Source for Filter 0 bit
11 = Reserved
10 = Acceptance Mask 2 registers contain mask
01 = Acceptance Mask 1 registers contain mask
00 = Acceptance Mask 0 registers contain mask
DS70592B-page 198
Preliminary
x = Bit is unknown
 2009 Microchip Technology Inc.
PIC24HJXXXGPX06A/X08A/X10A
REGISTER 19-19: CiFMSKSEL2: ECAN™ FILTER 15-8 MASK SELECTION REGISTER
R/W-0
R/W-0
F15MSK<1:0>
bit 15
R/W-0
R/W-0
F14MSK<1:0>
R/W-0
R/W-0
F13MSK<1:0>
R/W-0
R/W-0
F12MSK<1:0>
bit 8
R/W-0
R/W-0
F11MSK<1:0>
bit 7
R/W-0
R/W-0
F10MSK<1:0>
R/W-0
R/W-0
F9MSK<1:0>
R/W-0
R/W-0
F8MSK<1:0>
bit 0
Legend:
R = Readable bit
-n = Value at POR
bit 15-14
bit 13-12
bit 11-10
bit 9-8
bit 7-6
bit 5-4
bit 3-2
bit 1-0
W = Writable bit
‘1’ = Bit is set
U = Unimplemented bit, read as ‘0’
‘0’ = Bit is cleared
x = Bit is unknown
F15MSK<1:0>: Mask Source for Filter 15 bit
11 = Reserved
10 = Acceptance Mask 2 registers contain mask
01 = Acceptance Mask 1 registers contain mask
00 = Acceptance Mask 0 registers contain mask
F14MSK<1:0>: Mask Source for Filter 14 bit (same values as bit 15-14)
F13MSK<1:0>: Mask Source for Filter 13 bit (same values as bit 15-14)
F12MSK<1:0>: Mask Source for Filter 12 bit (same values as bit 15-14)
F11MSK<1:0>: Mask Source for Filter 11 bit (same values as bit 15-14)
F10MSK<1:0>: Mask Source for Filter 10 bit (same values as bit 15-14)
F9MSK<1:0>: Mask Source for Filter 9 bit (same values as bit 15-14)
F8MSK<1:0>: Mask Source for Filter 8 bit (same values as bit 15-14)
 2009 Microchip Technology Inc.
Preliminary
DS70592B-page 199
PIC24HJXXXGPX06A/X08A/X10A
REGISTER 19-20: CiRXMnSID: ECAN™ MODULE ACCEPTANCE FILTER MASK n STANDARD
IDENTIFIER
R/W-x
R/W-x
R/W-x
R/W-x
R/W-x
R/W-x
R/W-x
R/W-x
SID10
SID9
SID8
SID7
SID6
SID5
SID4
SID3
bit 15
bit 8
R/W-x
R/W-x
R/W-x
U-0
R/W-x
U-0
R/W-x
R/W-x
SID2
SID1
SID0
—
MIDE
—
EID17
EID16
bit 7
bit 0
Legend:
R = Readable bit
W = Writable bit
U = Unimplemented bit, read as ‘0’
-n = Value at POR
‘1’ = Bit is set
‘0’ = Bit is cleared
x = Bit is unknown
bit 15-5
SID<10:0>: Standard Identifier bits
1 = Include bit SIDx in filter comparison
0 = Bit SIDx is don’t care in filter comparison
bit 4
Unimplemented: Read as ‘0’
bit 3
MIDE: Identifier Receive Mode bit
1 = Match only message types (standard or extended address) that correspond to EXIDE bit in filter
0 = Match either standard or extended address message if filters match
(i.e., if (Filter SID) = (Message SID) or if (Filter SID/EID) = (Message SID/EID))
bit 2
Unimplemented: Read as ‘0’
bit 1-0
EID<17:16>: Extended Identifier bits
1 = Include bit EIDx in filter comparison
0 = Bit EIDx is don’t care in filter comparison
REGISTER 19-21: CiRXMnEID: ECAN™ TECHNOLOGY ACCEPTANCE FILTER MASK n EXTENDED
IDENTIFIER
R/W-x
R/W-x
R/W-x
R/W-x
R/W-x
R/W-x
R/W-x
R/W-x
EID15
EID14
EID13
EID12
EID11
EID10
EID9
EID8
bit 15
bit 8
R/W-x
R/W-x
R/W-x
R/W-x
R/W-x
R/W-x
R/W-x
R/W-x
EID7
EID6
EID5
EID4
EID3
EID2
EID1
EID0
bit 7
bit 0
Legend:
R = Readable bit
W = Writable bit
U = Unimplemented bit, read as ‘0’
-n = Value at POR
‘1’ = Bit is set
‘0’ = Bit is cleared
bit 15-0
x = Bit is unknown
EID<15:0>: Extended Identifier bits
1 = Include bit EIDx in filter comparison
0 = Bit EIDx is don’t care in filter comparison
DS70592B-page 200
Preliminary
 2009 Microchip Technology Inc.
PIC24HJXXXGPX06A/X08A/X10A
REGISTER 19-22: CiRXFUL1: ECAN™ MODULE RECEIVE BUFFER FULL REGISTER 1
R/C-0
R/C-0
R/C-0
R/C-0
R/C-0
R/C-0
R/C-0
R/C-0
RXFUL15
RXFUL14
RXFUL13
RXFUL12
RXFUL11
RXFUL10
RXFUL9
RXFUL8
bit 15
bit 8
R/C-0
R/C-0
R/C-0
R/C-0
R/C-0
R/C-0
R/C-0
R/C-0
RXFUL7
RXFUL6
RXFUL5
RXFUL4
RXFUL3
RXFUL2
RXFUL1
RXFUL0
bit 7
bit 0
Legend:
C = Clear only bit
R = Readable bit
W = Writable bit
U = Unimplemented bit, read as ‘0’
-n = Value at POR
‘1’ = Bit is set
‘0’ = Bit is cleared
bit 15-0
x = Bit is unknown
RXFUL<15:0>: Receive Buffer n Full bits
1 = Buffer is full (set by module)
0 = Buffer is empty (clear by application software)
REGISTER 19-23: CiRXFUL2: ECAN™ MODULE RECEIVE BUFFER FULL REGISTER 2
R/C-0
R/C-0
R/C-0
R/C-0
R/C-0
R/C-0
R/C-0
R/C-0
RXFUL31
RXFUL30
RXFUL29
RXFUL28
RXFUL27
RXFUL26
RXFUL25
RXFUL24
bit 15
bit 8
R/C-0
R/C-0
R/C-0
R/C-0
R/C-0
R/C-0
R/C-0
R/C-0
RXFUL23
RXFUL22
RXFUL21
RXFUL20
RXFUL19
RXFUL18
RXFUL17
RXFUL16
bit 7
bit 0
Legend:
C = Clear only bit
R = Readable bit
W = Writable bit
U = Unimplemented bit, read as ‘0’
-n = Value at POR
‘1’ = Bit is set
‘0’ = Bit is cleared
bit 15-0
x = Bit is unknown
RXFUL<31:16>: Receive Buffer n Full bits
1 = Buffer is full (set by module)
0 = Buffer is empty (clear by application software)
 2009 Microchip Technology Inc.
Preliminary
DS70592B-page 201
PIC24HJXXXGPX06A/X08A/X10A
REGISTER 19-24: CiRXOVF1: ECAN™ MODULE RECEIVE BUFFER OVERFLOW REGISTER 1
R/C-0
R/C-0
R/C-0
R/C-0
R/C-0
R/C-0
R/C-0
R/C-0
RXOVF15
RXOVF14
RXOVF13
RXOVF12
RXOVF11
RXOVF10
RXOVF9
RXOVF8
bit 15
bit 8
R/C-0
R/C-0
R/C-0
R/C-0
R/C-0
R/C-0
R/C-0
R/C-0
RXOVF7
RXOVF6
RXOVF5
RXOVF4
RXOVF3
RXOVF2
RXOVF1
RXOVF0
bit 7
bit 0
Legend:
C = Clear only bit
R = Readable bit
W = Writable bit
U = Unimplemented bit, read as ‘0’
-n = Value at POR
‘1’ = Bit is set
‘0’ = Bit is cleared
bit 15-0
x = Bit is unknown
RXOVF<15:0>: Receive Buffer n Overflow bits
1 = Module pointed a write to a full buffer (set by module)
0 = Overflow is cleared (clear by application software)
REGISTER 19-25: CiRXOVF2: ECAN™ MODULE RECEIVE BUFFER OVERFLOW REGISTER 2
R/C-0
R/C-0
R/C-0
R/C-0
R/C-0
R/C-0
R/C-0
R/C-0
RXOVF31
RXOVF30
RXOVF29
RXOVF28
RXOVF27
RXOVF26
RXOVF25
RXOVF24
bit 15
bit 8
R/C-0
R/C-0
R/C-0
R/C-0
R/C-0
R/C-0
R/C-0
R/C-0
RXOVF23
RXOVF22
RXOVF21
RXOVF20
RXOVF19
RXOVF18
RXOVF17
RXOVF16
bit 7
bit 0
Legend:
C = Clear only bit
R = Readable bit
W = Writable bit
U = Unimplemented bit, read as ‘0’
-n = Value at POR
‘1’ = Bit is set
‘0’ = Bit is cleared
bit 15-0
x = Bit is unknown
RXOVF<31:16>: Receive Buffer n Overflow bits
1 = Module pointed a write to a full buffer (set by module)
0 = Overflow is cleared (clear by application software)
DS70592B-page 202
Preliminary
 2009 Microchip Technology Inc.
PIC24HJXXXGPX06A/X08A/X10A
REGISTER 19-26:
CiTRmnCON: ECAN™ MODULE TX/RX BUFFER m CONTROL REGISTER
(m = 0,2,4,6; n = 1,3,5,7)
R/W-0
R-0
R-0
R-0
R/W-0
R/W-0
TXENn
TXABTn
TXLARBn
TXERRn
TXREQn
RTRENn
R/W-0
R/W-0
TXnPRI<1:0>
bit 15
bit 8
R/W-0
R-0
TXENm
TXABTm(1)
R-0
R-0
TXLARBm(1) TXERRm(1)
R/W-0
R/W-0
TXREQm
RTRENm
R/W-0
R/W-0
TXmPRI<1:0>
bit 7
bit 0
Legend:
R = Readable bit
W = Writable bit
U = Unimplemented bit, read as ‘0’
-n = Value at POR
‘1’ = Bit is set
‘0’ = Bit is cleared
x = Bit is unknown
bit 15-8
See Definition for Bits 7-0, Controls Buffer n
bit 7
TXENm: TX/RX Buffer Selection bit
1 = Buffer TRBn is a transmit buffer
0 = Buffer TRBn is a receive buffer
bit 6
TXABTm: Message Aborted bit(1)
1 = Message was aborted
0 = Message completed transmission successfully
bit 5
TXLARBm: Message Lost Arbitration bit(1)
1 = Message lost arbitration while being sent
0 = Message did not lose arbitration while being sent
bit 4
TXERRm: Error Detected During Transmission bit(1)
1 = A bus error occurred while the message was being sent
0 = A bus error did not occur while the message was being sent
bit 3
TXREQm: Message Send Request bit
Setting this bit to ‘1’ requests sending a message. The bit will automatically clear when the message
is successfully sent. Clearing the bit to ‘0’ while set will request a message abort.
bit 2
RTRENm: Auto-Remote Transmit Enable bit
1 = When a remote transmit is received, TXREQ will be set
0 = When a remote transmit is received, TXREQ will be unaffected
bit 1-0
TXmPRI<1:0>: Message Transmission Priority bits
11 = Highest message priority
10 = High intermediate message priority
01 = Low intermediate message priority
00 = Lowest message priority
Note 1: This bit is cleared when TXREQ is set.
 2009 Microchip Technology Inc.
Preliminary
DS70592B-page 203
PIC24HJXXXGPX06A/X08A/X10A
Note:
The buffers, SID, EID, DLC, Data Field and Receive Status registers are stored in DMA RAM. These are
not Special Function Registers.
REGISTER 19-27: CiTRBnSID: ECAN™ MODULE BUFFER n STANDARD IDENTIFIER
(n = 0, 1, ..., 31)
U-0
U-0
U-0
R/W-x
R/W-x
R/W-x
R/W-x
R/W-x
—
—
—
SID10
SID9
SID8
SID7
SID6
bit 15
bit 8
R/W-x
R/W-x
R/W-x
R/W-x
R/W-x
R/W-x
R/W-x
R/W-x
SID5
SID4
SID3
SID2
SID1
SID0
SRR
IDE
bit 7
bit 0
Legend:
R = Readable bit
W = Writable bit
U = Unimplemented bit, read as ‘0’
-n = Value at POR
‘1’ = Bit is set
‘0’ = Bit is cleared
bit 15-13
Unimplemented: Read as ‘0’
bit 12-2
SID<10:0>: Standard Identifier bits
bit 1
SRR: Substitute Remote Request bit
1 = Message will request remote transmission
0 = Normal message
bit 0
IDE: Extended Identifier bit
1 = Message will transmit extended identifier
0 = Message will transmit standard identifier
x = Bit is unknown
REGISTER 19-28: CiTRBnEID: ECAN™ MODULE BUFFER n EXTENDED IDENTIFIER
(n = 0, 1, ..., 31)
U-0
U-0
U-0
U-0
R/W-x
R/W-x
R/W-x
R/W-x
—
—
—
—
EID17
EID16
EID15
EID14
bit 15
bit 8
R/W-x
R/W-x
R/W-x
R/W-x
R/W-x
R/W-x
R/W-x
R/W-x
EID13
EID12
EID11
EID10
EID9
EID8
EID7
EID6
bit 7
bit 0
Legend:
R = Readable bit
W = Writable bit
U = Unimplemented bit, read as ‘0’
-n = Value at POR
‘1’ = Bit is set
‘0’ = Bit is cleared
bit 15-12
Unimplemented: Read as ‘0’
bit 11-0
EID<17:6>: Extended Identifier bits
DS70592B-page 204
Preliminary
x = Bit is unknown
 2009 Microchip Technology Inc.
PIC24HJXXXGPX06A/X08A/X10A
REGISTER 19-29: CiTRBnDLC: ECAN™ MODULE BUFFER n DATA LENGTH CONTROL
(n = 0, 1, ..., 31)
R/W-x
R/W-x
R/W-x
R/W-x
R/W-x
R/W-x
R/W-x
R/W-x
EID5
EID4
EID3
EID2
EID1
EID0
RTR
RB1
bit 15
bit 8
U-0
U-0
U-0
R/W-x
R/W-x
R/W-x
R/W-x
R/W-x
—
—
—
RB0
DLC3
DLC2
DLC1
DLC0
bit 7
bit 0
Legend:
R = Readable bit
W = Writable bit
U = Unimplemented bit, read as ‘0’
-n = Value at POR
‘1’ = Bit is set
‘0’ = Bit is cleared
bit 15-10
EID<5:0>: Extended Identifier bits
bit 9
RTR: Remote Transmission Request bit
1 = Message will request remote transmission
0 = Normal message
bit 8
RB1: Reserved Bit 1
User must set this bit to ‘0’ per CAN protocol.
bit 7-5
Unimplemented: Read as ‘0’
bit 4
RB0: Reserved Bit 0
User must set this bit to ‘0’ per CAN protocol.
bit 3-0
DLC<3:0>: Data Length Code bits
REGISTER 19-30:
x = Bit is unknown
CiTRBnDm: ECAN™ MODULE BUFFER n DATA FIELD BYTE m
(n = 0, 1, ..., 31; m = 0, 1, ..., 7)(1)
R/W-x
R/W-x
R/W-x
R/W-x
R/W-x
R/W-x
R/W-x
R/W-x
TRBnDm7
TRBnDm6
TRBnDm5
TRBnDm4
TRBnDm3
TRBnDm2
TRBnDm1
TRBnDm0
bit 7
bit 0
Legend:
R = Readable bit
W = Writable bit
U = Unimplemented bit, read as ‘0’
-n = Value at POR
‘1’ = Bit is set
‘0’ = Bit is cleared
bit 7-0
x = Bit is unknown
TRnDm<7:0>: Data Field Buffer ‘n’ Byte ‘m’ bits
Note 1: The Most Significant Byte contains byte (m + 1) of the buffer.
 2009 Microchip Technology Inc.
Preliminary
DS70592B-page 205
PIC24HJXXXGPX06A/X08A/X10A
REGISTER 19-31: CiTRBnSTAT: ECAN™ MODULE RECEIVE BUFFER n STATUS
(n = 0, 1, ..., 31)
U-0
U-0
U-0
R/W-x
R/W-x
R/W-x
R/W-x
R/W-x
—
—
—
FILHIT4
FILHIT3
FILHIT2
FILHIT1
FILHIT0
bit 15
bit 8
U-0
U-0
U-0
U-0
U-0
U-0
U-0
U-0
—
—
—
—
—
—
—
—
bit 7
bit 0
Legend:
R = Readable bit
W = Writable bit
U = Unimplemented bit, read as ‘0’
-n = Value at POR
‘1’ = Bit is set
‘0’ = Bit is cleared
x = Bit is unknown
bit 15-13
Unimplemented: Read as ‘0’
bit 12-8
FILHIT<4:0>: Filter Hit Code bits (only written by module for receive buffers, unused for transmit buffers)
Encodes number of filter that resulted in writing this buffer.
bit 7-0
Unimplemented: Read as ‘0’
DS70592B-page 206
Preliminary
 2009 Microchip Technology Inc.
PIC24HJXXXGPX06A/X08A/X10A
20.0
10-BIT/12-BIT
ANALOG-TO-DIGITAL
CONVERTER (ADC)
Note 1: This data sheet summarizes the features
of the PIC24HJXXXGPX06A/X08A/X10A
family of devices. However, it is not
intended to be a comprehensive reference source. To complement the information in this data sheet, refer to the
“dsPIC33F/PIC24H Family Reference
Manual”, Section 16. “Analog-to-Digital
Converter (ADC)” (DS70225), which is
available from the Microchip website
(www.microchip.com).
Depending on the particular device pinout, the Analog-to-Digital Converter can have up to 32 analog input
pins, designated AN0 through AN31. In addition, there
are two analog input pins for external voltage reference
connections. These voltage reference inputs may be
shared with other analog input pins. The actual number
of analog input pins and external voltage reference
input configuration will depend on the specific device.
Refer to the device data sheet for further details.
A block diagram of the Analog-to-Digital Converter is
shown in Figure 20-1.
20.2
The following configuration steps should be performed.
1.
2: Some registers and associated bits
described in this section may not be available on all devices. Refer to Section 4.0
“Memory Organization” in this data
sheet for device-specific register and bit
information.
The PIC24HJXXXGPX06A/X08A/X10A devices have
up to 32 Analog-to-Digital input channels. These
devices also have up to 2 Analog-to-Digital converter
modules (ADCx, where ‘x’ = 1 or 2), each with its own
set of Special Function Registers.
The AD12B bit (ADxCON1<10>) allows each of the
ADC modules to be configured by the user as either a
10-bit, 4-sample/hold ADC (default configuration) or a
12-bit, 1-sample/hold ADC.
Note:
The ADC module needs to be disabled
before modifying the AD12B bit.
2.
20.1
Key Features
The 10-bit ADC configuration has the following key
features:
•
•
•
•
•
•
•
•
•
•
Successive Approximation (SAR) conversion
Conversion speeds of up to 1.1 Msps
Up to 32 analog input pins
External voltage reference input pins
Simultaneous sampling of up to four analog input
pins
Automatic Channel Scan mode
Selectable conversion trigger source
Selectable Buffer Fill modes
Two result alignment options (signed/unsigned)
Operation during CPU Sleep and Idle modes
The 12-bit ADC configuration supports all the above
features, except:
• In the 12-bit configuration, conversion speeds of
up to 500 ksps are supported
• There is only 1 sample/hold amplifier in the 12-bit
configuration, so simultaneous sampling of
multiple channels is not supported.
 2009 Microchip Technology Inc.
Analog-to-Digital Initialization
Configure the ADC module:
a) Select port pins as analog inputs
(ADxPCFGH<15:0> or ADxPCFGL<15:0>)
b) Select voltage reference source to match
expected range on analog inputs
(ADxCON2<15:13>)
c) Select the analog conversion clock to
match desired data rate with processor
clock (ADxCON3<7:0>)
d) Determine how many S/H channels will
be
used
(ADxCON2<9:8>
and
ADxPCFGH<15:0> or ADxPCFGL<15:0>)
e) Select the appropriate sample/conversion
sequence
(ADxCON1<7:5>
and
ADxCON3<12:8>)
f) Select how conversion results are
presented in the buffer (ADxCON1<9:8>)
g) Turn on the ADC module (ADxCON1<15>)
Configure ADC interrupt (if required):
a) Clear the ADxIF bit
b) Select ADC interrupt priority
20.3
ADC and DMA
If more than one conversion result needs to be buffered
before triggering an interrupt, DMA data transfers can
be used. Both ADC1 and ADC2 can trigger a DMA data
transfer. If ADC1 or ADC2 is selected as the DMA IRQ
source, a DMA transfer occurs when the AD1IF or
AD2IF bit gets set as a result of an ADC1 or ADC2
sample conversion sequence.
The SMPI<3:0> bits (ADxCON2<5:2>) are used to
select how often the DMA RAM buffer pointer is
incremented.
The ADDMABM bit (ADxCON1<12>) determines how
the conversion results are filled in the DMA RAM buffer
area being used for ADC. If this bit is set, DMA buffers
are written in the order of conversion. The module will
provide an address to the DMA channel that is the
same as the address used for the non-DMA
stand-alone buffer. If the ADDMABM bit is cleared, then
DMA buffers are written in Scatter/Gather mode. The
module will provide a scatter/gather address to the
DMA channel, based on the index of the analog input
and the size of the DMA buffer.
Preliminary
DS70592B-page 207
PIC24HJXXXGPX06A/X08A/X10A
FIGURE 20-1:
ADCx MODULE BLOCK DIAGRAM
AN0
ANy(3)
S/H0
CHANNEL
SCAN
+
CH0SA<4:0>
CH0
CH0SB<4:0>
-
CSCNA
AN1
VREFL
CH0NA CH0NB
AN0
(1)
VREFL+(1)AVDD VREFL- AVSS
AN3
S/H1
+
-
CH123SA CH123SB
CH1(2)
AN6
VCFG<2:0>
AN9
VREFL
VREFH
VREFL
CH123NA CH123NB
SAR ADC
ADC1BUF0
AN1
AN4
S/H2
+
CH123SA CH123SB
CH2(2)
-
AN7
AN10
VREFL
CH123NA CH123NB
AN2
AN5
S/H3
+
CH123SA CH123SB
CH3(2)
-
AN8
AN11
VREFL
CH123NA CH123NB
Alternate
Input Selection
Note
1:
2:
3:
VREF+, VREF- inputs can be multiplexed with other analog inputs.
Channels 1, 2 and 3 are not applicable for the 12-bit mode of operation.
For 64-pin devices, y = 17; for 100-pin devices, y =31; for ADC2, y = 15.
DS70592B-page 208
Preliminary
 2009 Microchip Technology Inc.
PIC24HJXXXGPX06A/X08A/X10A
FIGURE 20-2:
ANALOG-TO-DIGITAL CONVERSION CLOCK PERIOD BLOCK DIAGRAM
ADxCON3<15>
ADC Internal
RC Clock(2)
0
TAD
ADxCON3<5:0>
1
6
TOSC(1)
X2
TCY
ADC Conversion
Clock Multiplier
1, 2, 3, 4, 5,..., 64
Note
1:
Refer to Figure 9-2 for the derivation of FOSC when the PLL is enabled. If the PLL is not used, FOSC is equal to the clock source
frequency. TOSC = 1/FOSC.
2:
See the ADC electrical specifications for exact RC clock value.
 2009 Microchip Technology Inc.
Preliminary
DS70592B-page 209
PIC24HJXXXGPX06A/X08A/X10A
REGISTER 20-1:
ADxCON1: ADCx CONTROL REGISTER 1(where x = 1 or 2)
R/W-0
U-0
R/W-0
R/W-0
U-0
R/W-0
ADON
—
ADSIDL
ADDMABM
—
AD12B
R/W-0
R/W-0
FORM<1:0>
bit 15
bit 8
R/W-0
R/W-0
R/W-0
SSRC<2:0>
U-0
R/W-0
R/W-0
R/W-0
HC,HS
R/C-0
HC, HS
—
SIMSAM
ASAM
SAMP
DONE
bit 7
bit 0
Legend:
HC = Cleared by hardware
HS = Set by hardware
R = Readable bit
W = Writable bit
U = Unimplemented bit, read as ‘0’
-n = Value at POR
‘1’ = Bit is set
‘0’ = Bit is cleared
x = Bit is unknown
bit 15
ADON: ADC Operating Mode bit
1 = ADC module is operating
0 = ADC module is off
bit 14
Unimplemented: Read as ‘0’
bit 13
ADSIDL: Stop in Idle Mode bit
1 = Discontinue module operation when device enters Idle mode
0 = Continue module operation in Idle mode
bit 12
ADDMABM: DMA Buffer Build Mode bit
1 = DMA buffers are written in the order of conversion. The module will provide an address to the DMA
channel that is the same as the address used for the non-DMA stand-alone buffer
0 = DMA buffers are written in Scatter/Gather mode. The module will provide a scatter/gather address
to the DMA channel, based on the index of the analog input and the size of the DMA buffer
bit 11
Unimplemented: Read as ‘0’
bit 10
AD12B: 10-Bit or 12-Bit Operation Mode bit
1 = 12-bit, 1-channel ADC operation
0 = 10-bit, 4-channel ADC operation
bit 9-8
FORM<1:0>: Data Output Format bits
For 10-bit operation:
11 = Reserved
10 = Reserved
01 = Signed integer (DOUT = ssss sssd dddd dddd, where s = .NOT.d<9>)
00 = Integer (DOUT = 0000 00dd dddd dddd)
For 12-bit operation:
11 = Reserved
10 = Reserved
01 = Signed Integer (DOUT = ssss sddd dddd dddd, where s = .NOT.d<11>)
00 = Integer (DOUT = 0000 dddd dddd dddd)
bit 7-5
SSRC<2:0>: Sample Clock Source Select bits
111 = Internal counter ends sampling and starts conversion (auto-convert)
110 = Reserved
101 = Reserved
100 = GP timer (Timer5 for ADC1, Timer3 for ADC2) compare ends sampling and starts conversion
011 = Reserved
010 = GP timer (Timer3 for ADC1, Timer5 for ADC2) compare ends sampling and starts conversion
001 = Active transition on INT0 pin ends sampling and starts conversion
000 = Clearing sample bit ends sampling and starts conversion
bit 4
Unimplemented: Read as ‘0’
DS70592B-page 210
Preliminary
 2009 Microchip Technology Inc.
PIC24HJXXXGPX06A/X08A/X10A
REGISTER 20-1:
ADxCON1: ADCx CONTROL REGISTER 1(where x = 1 or 2) (CONTINUED)
bit 3
SIMSAM: Simultaneous Sample Select bit (only applicable when CHPS<1:0> = 01 or 1x)
When AD12B = 1, SIMSAM is: U-0, Unimplemented, Read as ‘0’
1 = Samples CH0, CH1, CH2, CH3 simultaneously (when CHPS<1:0> = 1x); or
Samples CH0 and CH1 simultaneously (when CHPS<1:0> = 01)
0 = Samples multiple channels individually in sequence
bit 2
ASAM: ADC Sample Auto-Start bit
1 = Sampling begins immediately after last conversion. SAMP bit is auto-set
0 = Sampling begins when SAMP bit is set
bit 1
SAMP: ADC Sample Enable bit
1 = ADC sample/hold amplifiers are sampling
0 = ADC sample/hold amplifiers are holding
If ASAM = 0, software may write ‘1’ to begin sampling. Automatically set by hardware if ASAM = 1.
If SSRC = 000, software may write ‘0’ to end sampling and start conversion. If SSRC 000,
automatically cleared by hardware to end sampling and start conversion.
bit 0
DONE: ADC Conversion Status bit
1 = ADC conversion cycle is completed.
0 = ADC conversion not started or in progress
Automatically set by hardware when analog-to-digital conversion is complete. Software may write ‘0’
to clear DONE status (software not allowed to write ‘1’). Clearing this bit will NOT affect any operation
in progress. Automatically cleared by hardware at start of a new conversion.
 2009 Microchip Technology Inc.
Preliminary
DS70592B-page 211
PIC24HJXXXGPX06A/X08A/X10A
REGISTER 20-2:
R/W-0
ADxCON2: ADCx CONTROL REGISTER 2 (where x = 1 or 2)
R/W-0
R/W-0
VCFG<2:0>
U-0
U-0
R/W-0
—
—
CSCNA
R/W-0
R/W-0
CHPS<1:0>
bit 15
bit 8
R-0
U-0
BUFS
—
R/W-0
R/W-0
R/W-0
R/W-0
SMPI<3:0>
R/W-0
R/W-0
BUFM
ALTS
bit 7
bit 0
Legend:
R = Readable bit
W = Writable bit
U = Unimplemented bit, read as ‘0’
-n = Value at POR
‘1’ = Bit is set
‘0’ = Bit is cleared
bit 15-13
x = Bit is unknown
VCFG<2:0>: Converter Voltage Reference Configuration bits
VREF+
VREF-
000
AVDD
AVSS
001
External VREF+
AVSS
010
AVDD
External VREF-
011
External VREF+
External VREF-
1xx
AVDD
AVSS
bit 12-11
Unimplemented: Read as ‘0’
bit 10
CSCNA: Scan Input Selections for CH0+ during Sample A bit
1 = Scan inputs
0 = Do not scan inputs
bit 9-8
CHPS<1:0>: Selects Channels Utilized bits
When AD12B = 1, CHPS<1:0> is: U-0, Unimplemented, Read as ‘0’
1x = Converts CH0, CH1, CH2 and CH3
01 = Converts CH0 and CH1
00 = Converts CH0
bit 7
BUFS: Buffer Fill Status bit (only valid when BUFM = 1)
1 = ADC is currently filling second half of buffer, user should access data in first half
0 = ADC is currently filling first half of buffer, user should access data in second half
bit 6
Unimplemented: Read as ‘0’
bit 5-2
SMPI<3:0>: Selects Increment Rate for DMA Addresses bits or number of sample/conversion
operations per interrupt
1111 = Increments the DMA address or generates interrupt after completion of every 16th
sample/conversion operation
1110 = Increments the DMA address or generates interrupt after completion of every 15th
sample/conversion operation
•
•
•
0001 = Increments the DMA address or generates interrupt after completion of every 2nd
sample/conversion operation
0000 = Increments the DMA address or generates interrupt after completion of every
sample/conversion operation
bit 1
BUFM: Buffer Fill Mode Select bit
1 = Starts filling first half of buffer on first interrupt and second half of buffer on next interrupt
0 = Always starts filling buffer from the beginning
bit 0
ALTS: Alternate Input Sample Mode Select bit
1 = Uses channel input selects for Sample A on first sample and Sample B on next sample
0 = Always uses channel input selects for Sample A
DS70592B-page 212
Preliminary
 2009 Microchip Technology Inc.
PIC24HJXXXGPX06A/X08A/X10A
REGISTER 20-3:
ADxCON3: ADCx CONTROL REGISTER 3
R/W-0
U-0
U-0
ADRC
—
—
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
SAMC<4:0>(1)
bit 15
bit 8
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
ADCS<7:0>(2)
bit 7
bit 0
Legend:
R = Readable bit
W = Writable bit
U = Unimplemented bit, read as ‘0’
-n = Value at POR
‘1’ = Bit is set
‘0’ = Bit is cleared
bit 15
ADRC: ADC Conversion Clock Source bit
1 = ADC internal RC clock
0 = Clock derived from system clock
bit 14-13
Unimplemented: Read as ‘0’
bit 12-8
SAMC<4:0>: Auto Sample Time bits(1)
11111 = 31 TAD
•
•
•
00001 = 1 TAD
00000 = 0 TAD
bit 7-0
ADCS<7:0>: Analog-to-Digital Conversion Clock Select bits(2)
11111111 = Reserved
•
•
•
01000000 = Reserved
00111111 = TCY · (ADCS<7:0> + 1) = 64 · TCY = TAD
•
•
•
00000010 = TCY · (ADCS<7:0> + 1) = 3 · TCY = TAD
00000001 = TCY · (ADCS<7:0> + 1) = 2 · TCY = TAD
00000000 = TCY · (ADCS<7:0> + 1) = 1 · TCY = TAD
x = Bit is unknown
Note 1: This bit only used if ADxCON1<7:5> (SSRC<2:0>) = 111.
2: This bit is not used if ADxCON3<15> (ADRC) = 1.
 2009 Microchip Technology Inc.
Preliminary
DS70592B-page 213
PIC24HJXXXGPX06A/X08A/X10A
REGISTER 20-4:
ADxCON4: ADCx CONTROL REGISTER 4
U-0
U-0
U-0
U-0
U-0
U-0
U-0
U-0
—
—
—
—
—
—
—
—
bit 15
bit 8
U-0
U-0
U-0
U-0
U-0
—
—
—
—
—
R/W-0
R/W-0
R/W-0
DMABL<2:0>
bit 7
bit 0
Legend:
R = Readable bit
W = Writable bit
U = Unimplemented bit, read as ‘0’
-n = Value at POR
‘1’ = Bit is set
‘0’ = Bit is cleared
x = Bit is unknown
bit 15-3
Unimplemented: Read as ‘0’
bit 2-0
DMABL<2:0>: Selects Number of DMA Buffer Locations per Analog Input bits
111 = Allocates 128 words of buffer to each analog input
110 = Allocates 64 words of buffer to each analog input
101 = Allocates 32 words of buffer to each analog input
100 = Allocates 16 words of buffer to each analog input
011 = Allocates 8 words of buffer to each analog input
010 = Allocates 4 words of buffer to each analog input
001 = Allocates 2 words of buffer to each analog input
000 = Allocates 1 word of buffer to each analog input
DS70592B-page 214
Preliminary
 2009 Microchip Technology Inc.
PIC24HJXXXGPX06A/X08A/X10A
REGISTER 20-5:
ADxCHS123: ADCx INPUT CHANNEL 1, 2, 3 SELECT REGISTER
U-0
U-0
U-0
U-0
U-0
—
—
—
—
—
R/W-0
R/W-0
CH123NB<1:0>
R/W-0
CH123SB
bit 15
bit 8
U-0
U-0
U-0
U-0
U-0
—
—
—
—
—
R/W-0
R/W-0
CH123NA<1:0>
R/W-0
CH123SA
bit 7
bit 0
Legend:
R = Readable bit
W = Writable bit
U = Unimplemented bit, read as ‘0’
-n = Value at POR
‘1’ = Bit is set
‘0’ = Bit is cleared
x = Bit is unknown
bit 15-11
Unimplemented: Read as ‘0’
bit 10-9
CH123NB<1:0>: Channel 1, 2, 3 Negative Input Select for Sample B bits
When AD12B = 1, CHxNB is: U-0, Unimplemented, Read as ‘0’
11 = CH1 negative input is AN9, CH2 negative input is AN10, CH3 negative input is AN11
10 = CH1 negative input is AN6, CH2 negative input is AN7, CH3 negative input is AN8
0x = CH1, CH2, CH3 negative input is VREF-
bit 8
CH123SB: Channel 1, 2, 3 Positive Input Select for Sample B bit
When AD12B = 1, CHxSB is: U-0, Unimplemented, Read as ‘0’
1 = CH1 positive input is AN3, CH2 positive input is AN4, CH3 positive input is AN5
0 = CH1 positive input is AN0, CH2 positive input is AN1, CH3 positive input is AN2
bit 7-3
Unimplemented: Read as ‘0’
bit 2-1
CH123NA<1:0>: Channel 1, 2, 3 Negative Input Select for Sample A bits
When AD12B = 1, CHxNA is: U-0, Unimplemented, Read as ‘0’
11 = CH1 negative input is AN9, CH2 negative input is AN10, CH3 negative input is AN11
10 = CH1 negative input is AN6, CH2 negative input is AN7, CH3 negative input is AN8
0x = CH1, CH2, CH3 negative input is VREF-
bit 0
CH123SA: Channel 1, 2, 3 Positive Input Select for Sample A bit
When AD12B = 1, CHxSA is: U-0, Unimplemented, Read as ‘0’
1 = CH1 positive input is AN3, CH2 positive input is AN4, CH3 positive input is AN5
0 = CH1 positive input is AN0, CH2 positive input is AN1, CH3 positive input is AN2
 2009 Microchip Technology Inc.
Preliminary
DS70592B-page 215
PIC24HJXXXGPX06A/X08A/X10A
REGISTER 20-6:
ADxCHS0: ADCx INPUT CHANNEL 0 SELECT REGISTER
R/W-0
U-0
U-0
CH0NB
—
—
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
CH0SB<4:0>
bit 15
bit 8
R/W-0
U-0
U-0
CH0NA
—
—
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
CH0SA<4:0>
bit 7
bit 0
Legend:
R = Readable bit
W = Writable bit
U = Unimplemented bit, read as ‘0’
-n = Value at POR
‘1’ = Bit is set
‘0’ = Bit is cleared
bit 15
CH0NB: Channel 0 Negative Input Select for Sample B bit
Same definition as bit 7.
bit 14-13
Unimplemented: Read as ‘0’
bit 12-8
CH0SB<4:0>: Channel 0 Positive Input Select for Sample B bits
Same definition as bit<4:0>.
bit 7
CH0NA: Channel 0 Negative Input Select for Sample A bit
1 = Channel 0 negative input is AN1
0 = Channel 0 negative input is VREF-
bit 6-5
Unimplemented: Read as ‘0’
bit 4-0
CH0SA<4:0>: Channel 0 Positive Input Select for Sample A bits
11111 = Channel 0 positive input is AN31
11110 = Channel 0 positive input is AN30
•
•
•
00010 = Channel 0 positive input is AN2
00001 = Channel 0 positive input is AN1
00000 = Channel 0 positive input is AN0
Note:
x = Bit is unknown
ADC2 can only select AN0 through AN15 as positive inputs.
DS70592B-page 216
Preliminary
 2009 Microchip Technology Inc.
PIC24HJXXXGPX06A/X08A/X10A
REGISTER 20-7:
ADxCSSH: ADCx INPUT SCAN SELECT REGISTER HIGH(1,2)
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
CSS31
CSS30
CSS29
CSS28
CSS27
CSS26
CSS25
CSS24
bit 15
bit 8
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
CSS23
CSS22
CSS21
CSS20
CSS19
CSS18
CSS17
CSS16
bit 7
bit 0
Legend:
R = Readable bit
W = Writable bit
U = Unimplemented bit, read as ‘0’
-n = Value at POR
‘1’ = Bit is set
‘0’ = Bit is cleared
bit 15-0
x = Bit is unknown
CSS<31:16>: ADC Input Scan Selection bits
1 = Select ANx for input scan
0 = Skip ANx for input scan
Note 1: On devices without 32 analog inputs, all ADxCSSH bits may be selected by user. However, inputs selected
for scan without a corresponding input on device will convert VREFL.
2: CSSx = ANx, where x = 16 through 31.
REGISTER 20-8:
ADxCSSL: ADCx INPUT SCAN SELECT REGISTER LOW(1,2)
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
CSS15
CSS14
CSS13
CSS12
CSS11
CSS10
CSS9
CSS8
bit 15
bit 8
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
CSS7
CSS6
CSS5
CSS4
CSS3
CSS2
CSS1
CSS0
bit 7
bit 0
Legend:
R = Readable bit
W = Writable bit
U = Unimplemented bit, read as ‘0’
-n = Value at POR
‘1’ = Bit is set
‘0’ = Bit is cleared
bit 15-0
x = Bit is unknown
CSS<15:0>: ADC Input Scan Selection bits
1 = Select ANx for input scan
0 = Skip ANx for input scan
Note 1: On devices without 16 analog inputs, all ADxCSSL bits may be selected by user. However, inputs selected
for scan without a corresponding input on device will convert VREF-.
2: CSSx = ANx, where x = 0 through 15.
 2009 Microchip Technology Inc.
Preliminary
DS70592B-page 217
PIC24HJXXXGPX06A/X08A/X10A
REGISTER 20-9:
AD1PCFGH: ADC1 PORT CONFIGURATION REGISTER HIGH(1,2,3,4)
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
PCFG31
PCFG30
PCFG29
PCFG28
PCFG27
PCFG26
PCFG25
PCFG24
bit 15
bit 8
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
PCFG23
PCFG22
PCFG21
PCFG20
PCFG19
PCFG18
PCFG17
PCFG16
bit 7
bit 0
Legend:
R = Readable bit
W = Writable bit
U = Unimplemented bit, read as ‘0’
-n = Value at POR
‘1’ = Bit is set
‘0’ = Bit is cleared
bit 15-0
x = Bit is unknown
PCFG<31:16>: ADC Port Configuration Control bits
1 = Port pin in Digital mode, port read input enabled, ADC input multiplexor connected to AVSS
0 = Port pin in Analog mode, port read input disabled, ADC samples pin voltage
Note 1: On devices without 32 analog inputs, all PCFG bits are R/W by user. However, PCFG bits are ignored on
ports without a corresponding input on device.
2: ADC2 only supports analog inputs AN0-AN15; therefore, no ADC2 high port Configuration register exists.
3: PCFGx = ANx, where x = 16 through 31.
4: PCFGx bits will have no effect if ADC module is disabled by setting ADxMD bit in the PMDx register. In
this case all port pins multiplexed with ANx will be in Digital mode.
REGISTER 20-10: ADxPCFGL: ADCx PORT CONFIGURATION REGISTER LOW(1,2,3,4)
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
PCFG15
PCFG14
PCFG13
PCFG12
PCFG11
PCFG10
PCFG9
PCFG8
bit 15
bit 8
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
PCFG7
PCFG6
PCFG5
PCFG4
PCFG3
PCFG2
PCFG1
PCFG0
bit 7
bit 0
Legend:
R = Readable bit
W = Writable bit
U = Unimplemented bit, read as ‘0’
-n = Value at POR
‘1’ = Bit is set
‘0’ = Bit is cleared
bit 15-0
x = Bit is unknown
PCFG<15:0>: ADC Port Configuration Control bits
1 = Port pin in Digital mode, port read input enabled, ADC input multiplexor connected to AVSS
0 = Port pin in Analog mode, port read input disabled, ADC samples pin voltage
Note 1: On devices without 16 analog inputs, all PCFG bits are R/W by user. However, PCFG bits are ignored on
ports without a corresponding input on device.
2: On devices with 2 analog-to-digital modules, both AD1PCFGL and AD2PCFGL will affect the configuration
of port pins multiplexed with AN0-AN15.
3: PCFGx = ANx, where x = 0 through 15.
4: PCFGx bits will have no effect if ADC module is disabled by setting ADxMD bit in the PMDx register. In
this case all port pins multiplexed with ANx will be in Digital mode.
DS70592B-page 218
Preliminary
 2009 Microchip Technology Inc.
PIC24HJXXXGPX06A/X08A/X10A
21.0
SPECIAL FEATURES
21.1
Configuration Bits
The Configuration bits can be programmed (read as
‘0’), or left unprogrammed (read as ‘1’), to select various device configurations. These bits are mapped
starting at program memory location 0xF80000.
Note 1: This data sheet summarizes the features
of the PIC24HJXXXGPX06A/X08A/X10A
families of devices. However, it is not
intended to be a comprehensive reference source. To complement the information in this data sheet, refer to Section
23.
“CodeGuard™
Security”
(DS70239), Section 24. “Programming
and Diagnostics” (DS70246), and Section 25. “Device Configuration”
(DS70231) in the “dsPIC33F/PIC24H
Family Reference Manual”, which is available from the Microchip web site
(www.microchip.com).
The device Configuration register map is shown in
Table 21-1.
The individual Configuration bit descriptions for the
Configuration registers are shown in Table 21-2.
Note that address 0xF80000 is beyond the user program
memory space. In fact, it belongs to the configuration
memory space (0x800000-0xFFFFFF), which can only
be accessed using table reads and table writes.
To prevent inadvertent configuration changes during
code execution, all programmable Configuration bits
are write-once. After a bit is initially programmed during
a power cycle, it cannot be written to again. Changing
a device configuration requires that power to the device
be cycled.
2: Some registers and associated bits
described in this section may not be available on all devices. Refer to Section 4.0
“Memory Organization” in this data
sheet for device-specific register and bit
information.
PIC24HJXXXGPX06A/X08A/X10A devices include
several features intended to maximize application flexibility and reliability, and minimize cost through elimination of external components. These are:
•
•
•
•
•
Flexible Configuration
Watchdog Timer (WDT)
Code Protection and CodeGuard™ Security
JTAG Boundary Scan Interface
In-Circuit Serial Programming™ (ICSP™)
programming capability
• In-Circuit Emulation
TABLE 21-1:
Address
DEVICE CONFIGURATION REGISTER MAP
Name
Bit 7
RBS<1:0>
0xF80000 FBS
0xF80002 FSS
0xF80004 FGS
0xF80006 FOSCSEL
0xF80008 FOSC
0xF8000A FWDT
0xF8000C FPOR
Bit 6
RSS<1:0>
—
—
IESO
Reserved(2)
FCKSM<1:0>
FWDTEN
0xF8000E FICD
0xF80010 FUID0
Bit 5
Bit 4
—
—
—
—
—
—
—
—
—
—
WINDIS PLLKEN(3)
Reserved(4)
Reserved(1)
JTAGEN
WDTPRE
—
Bit 3
Bit 2
Bit 1
Bit 0
BSS<2:0>
BWRP
—
SSS<2:0>
GSS<1:0>
SWRP
GWRP
—
—
FNOSC<2:0>
OSCIOFNC POSCMD<1:0>
—
—
—
User Unit ID Byte 0
0xF80012 FUID1
0xF80014 FUID2
User Unit ID Byte 1
User Unit ID Byte 2
0xF80016 FUID3
Legend: — = unimplemented bits, read as ‘0’.
User Unit ID Byte 3
WDTPOST<3:0>
FPWRT<2:0>
—
ICS<1:0>
Note 1: These bits are reserved for use by development tools and must be programmed as ‘1’.
2: When read, this bit returns the current programmed value.
3: This bit is unimplemented on PIC24HJ64GPX06A/X08A/X10A and PIC24HJ128GPX06A/X08A/X10A
devices and reads as ‘0’.
4: These bits are reserved and always read as ‘1’.
 2009 Microchip Technology Inc.
Preliminary
DS70592B-page 219
PIC24HJXXXGPX06A/X08A/X10A
TABLE 21-2:
PIC24HJXXXGPX06A/X08A/X10A CONFIGURATION BITS DESCRIPTION
Bit Field
Register
Description
BWRP
FBS
Boot Segment Program Flash Write Protection
1 = Boot segment may be written
0 = Boot segment is write-protected
BSS<2:0>
FBS
Boot Segment Program Flash Code Protection Size
X11 = No Boot program Flash segment
Boot space is 1K IW less VS
110 = Standard security; boot program Flash segment starts at End of VS,
ends at 0x0007FE
010 = High security; boot program Flash segment starts at End of VS, ends at
0x0007FE
Boot space is 4K IW less VS
101 = Standard security; boot program Flash segment starts at End of VS,
ends at 0x001FFE
001 = High security; boot program Flash segment starts at End of VS, ends at
0x001FFE
Boot space is 8K IW less VS
100 = Standard security; boot program Flash segment starts at End of VS,
ends at 0x003FFE
000 = High security; boot program Flash segment starts at End of VS, ends at
0x003FFE
RBS<1:0>
FBS
Boot Segment RAM Code Protection
11 = No Boot RAM defined
10 = Boot RAM is 128 Bytes
01 = Boot RAM is 256 Bytes
00 = Boot RAM is 1024 Bytes
SWRP
FSS
Secure Segment Program Flash Write Protection
1 = Secure segment may be written
0 = Secure segment is write-protected
DS70592B-page 220
Preliminary
 2009 Microchip Technology Inc.
PIC24HJXXXGPX06A/X08A/X10A
TABLE 21-2:
PIC24HJXXXGPX06A/X08A/X10A CONFIGURATION BITS DESCRIPTION (CONTINUED)
Bit Field
Register
SSS<2:0>
FSS
Description
Secure Segment Program Flash Code Protection Size
(FOR 128K and 256K DEVICES)
X11 = No Secure program Flash segment
Secure space is 8K IW less BS
110 = Standard security; secure program Flash segment starts at End of BS,
ends at 0x003FFE
010 = High security; secure program Flash segment starts at End of BS, ends
at 0x003FFE
Secure space is 16K IW less BS
101 = Standard security; secure program Flash segment starts at End of BS,
ends at 0x007FFE
001 = High security; secure program Flash segment starts at End of BS, ends
at 0x007FFE
Secure space is 32K IW less BS
100 = Standard security; secure program Flash segment starts at End of BS,
ends at 0x00FFFE
000 = High security; secure program Flash segment starts at End of BS, ends
at 0x00FFFE
(FOR 64K DEVICES)
X11 = No Secure program Flash segment
Secure space is 4K IW less BS
110 = Standard security; secure program Flash segment starts at End of BS,
ends at 0x001FFE
010 = High security; secure program Flash segment starts at End of BS, ends
at 0x001FFE
Secure space is 8K IW less BS
101 = Standard security; secure program Flash segment starts at End of BS,
ends at 0x003FFE
001 = High security; secure program Flash segment starts at End of BS, ends
at 0x003FFE
Secure space is 16K IW less BS
100 = Standard security; secure program Flash segment starts at End of BS,
ends at 0x007FFE
000 = High security; secure program Flash segment starts at End of BS, ends
at 0x007FFE
RSS<1:0>
FSS
Secure Segment RAM Code Protection
11 = No Secure RAM defined
10 = Secure RAM is 256 Bytes less BS RAM
01 = Secure RAM is 2048 Bytes less BS RAM
00 = Secure RAM is 4096 Bytes less BS RAM
GSS<1:0>
FGS
General Segment Code-Protect bit
11 = User program memory is not code-protected
10 = Standard Security; general program Flash segment starts at End of SS,
ends at EOM
0x = High Security; general program Flash segment starts at End of ESS, ends
at EOM
GWRP
FGS
General Segment Write-Protect bit
1 = User program memory is not write-protected
0 = User program memory is write-protected
 2009 Microchip Technology Inc.
Preliminary
DS70592B-page 221
PIC24HJXXXGPX06A/X08A/X10A
TABLE 21-2:
PIC24HJXXXGPX06A/X08A/X10A CONFIGURATION BITS DESCRIPTION (CONTINUED)
Bit Field
Register
IESO
FOSCSEL
Internal External Start-up Option bit
1 = Start-up device with FRC, then automatically switch to the user-selected
oscillator source when ready
0 = Start-up device with user-selected oscillator source
FNOSC<2:0>
FOSCSEL
Initial Oscillator Source Selection bits
111 = Internal Fast RC (FRC) oscillator with postscaler
110 = Reserved
101 = LPRC oscillator
100 = Secondary (LP) oscillator
011 = Primary (XT, HS, EC) oscillator with PLL
010 = Primary (XT, HS, EC) oscillator
001 = Internal Fast RC (FRC) oscillator with PLL
000 = FRC oscillator
FCKSM<1:0>
FOSC
Clock Switching Mode bits
1x = Clock switching is disabled, Fail-Safe Clock Monitor is disabled
01 = Clock switching is enabled, Fail-Safe Clock Monitor is disabled
00 = Clock switching is enabled, Fail-Safe Clock Monitor is enabled
OSCIOFNC
FOSC
OSC2 Pin Function bit (except in XT and HS modes)
1 = OSC2 is clock output
0 = OSC2 is general purpose digital I/O pin
POSCMD<1:0>
FOSC
Primary Oscillator Mode Select bits
11 = Primary oscillator disabled
10 = HS Crystal Oscillator mode
01 = XT Crystal Oscillator mode
00 = EC (External Clock) mode
FWDTEN
FWDT
Watchdog Timer Enable bit
1 = Watchdog Timer always enabled (LPRC oscillator cannot be disabled. Clearing
the SWDTEN bit in the RCON register will have no effect.)
0 = Watchdog Timer enabled/disabled by user software (LPRC can be disabled
by clearing the SWDTEN bit in the RCON register)
WINDIS
FWDT
Watchdog Timer Window Enable bit
1 = Watchdog Timer in Non-Window mode
0 = Watchdog Timer in Window mode
PLLKEN
FWDT
PLL Lock Enable bit
1 = Clock switch to PLL source will wait until the PLL lock signal is valid.
0 = Clock switch will not wait for the PLL lock signal.
WDTPRE
FWDT
Watchdog Timer Prescaler bit
1 = 1:128
0 = 1:32
WDTPOST
FWDT
Watchdog Timer Postscaler bits
1111 = 1:32,768
1110 = 1:16,384
.
.
.
0001 = 1:2
0000 = 1:1
DS70592B-page 222
Description
Preliminary
 2009 Microchip Technology Inc.
PIC24HJXXXGPX06A/X08A/X10A
TABLE 21-2:
PIC24HJXXXGPX06A/X08A/X10A CONFIGURATION BITS DESCRIPTION (CONTINUED)
Bit Field
Register
FPWRT<2:0>
FPOR
Power-on Reset Timer Value Select bits
111 = PWRT = 128 ms
110 = PWRT = 64 ms
101 = PWRT = 32 ms
100 = PWRT = 16 ms
011 = PWRT = 8 ms
010 = PWRT = 4 ms
001 = PWRT = 2 ms
000 = PWRT = Disabled
JTAGEN
FICD
JTAG Enable bits
1 = JTAG enabled
0 = JTAG disabled
ICS<1:0>
FICD
ICD Communication Channel Select bits
11 = Communicate on PGEC1 and PGED1
10 = Communicate on PGEC2 and PGED2
01 = Communicate on PGEC3 and PGED3
00 = Reserved
 2009 Microchip Technology Inc.
Description
Preliminary
DS70592B-page 223
PIC24HJXXXGPX06A/X08A/X10A
21.2
On-Chip Voltage Regulator
21.3
All of the PIC24HJXXXGPX06A/X08A/X10A devices
power their core digital logic at a nominal 2.5V. This
may create an issue for designs that are required to
operate at a higher typical voltage, such as 3.3V. To
simplify system design, all devices in the
PIC24HJXXXGPX06A/X08A/X10A family incorporate
an on-chip regulator that allows the device to run its
core logic from VDD.
The regulator provides power to the core from the other
VDD pins. The regulator requires that a low-ESR (less
than 5 ohms) capacitor (such as tantalum or ceramic)
be connected to the VCAP/VDDCORE pin (Figure 21-1).
This helps to maintain the stability of the regulator. The
recommended value for the filter capacitor is provided
in Table 24-13 of Section 24.1 “DC Characteristics”.
Note:
It is important for the low-ESR capacitor to
be placed as close as possible to the
VCAP/VDDCORE pin.
On a POR, it takes approximately 20 s for the on-chip
voltage regulator to generate an output voltage. During
this time, designated as TSTARTUP, code execution is
disabled. TSTARTUP is applied every time the device
resumes operation after any power-down.
FIGURE 21-1:
ON-CHIP VOLTAGE
REGULATOR(1)
CONNECTIONS
BOR: Brown-out Reset
The BOR (Brown-out Reset) module is based on an
internal voltage reference circuit that monitors the regulated voltage VCAP/VDDCORE. The main purpose of
the BOR module is to generate a device Reset when a
brown-out condition occurs. Brown-out conditions are
generally caused by glitches on the AC mains (i.e.,
missing portions of the AC cycle waveform due to bad
power transmission lines or voltage sags due to excessive current draw when a large inductive load is turned
on).
A BOR will generate a Reset pulse which will reset the
device. The BOR will select the clock source, based on
the device Configuration bit values (FNOSC<2:0> and
POSCMD<1:0>). Furthermore, if an oscillator mode is
selected, the BOR will activate the Oscillator Start-up
Timer (OST). The system clock is held until OST
expires. If the PLL is used, then the clock will be held
until the LOCK bit (OSCCON<5>) is ‘1’.
Concurrently, the PWRT time-out (TPWRT) will be
applied before the internal Reset is released. If
TPWRT = 0 and a crystal oscillator is being used, then
a nominal delay of TFSCM = 100 is applied. The total
delay in this case is TFSCM.
The BOR Status bit (RCON<1>) will be set to indicate
that a BOR has occurred. The BOR circuit continues to
operate while in Sleep or Idle modes and will reset the
device should VDD fall below the BOR threshold voltage.
3.3V
PIC24H
VDD
VCAP/VDDCORE
CEFC
Note 1:
2:
VSS
These are typical operating voltages. Refer to
TABLE 24-13: “Internal Voltage Regulator
Specifications” located in Section 24.1 “DC
Characteristics” for the full operating ranges
of VDD and VCAP/VDDCORE.
It is important for the low-ESR capacitor to
be placed as close as possible to the VCAP/
VDDCORE pin.
DS70592B-page 224
Preliminary
 2009 Microchip Technology Inc.
PIC24HJXXXGPX06A/X08A/X10A
21.4
Watchdog Timer (WDT)
For PIC24HJXXXGPX06A/X08A/X10A devices, the
WDT is driven by the LPRC oscillator. When the WDT
is enabled, the clock source is also enabled.
The nominal WDT clock source from LPRC is 32 kHz.
This feeds a prescaler than can be configured for either
5-bit (divide-by-32) or 7-bit (divide-by-128) operation.
The prescaler is set by the WDTPRE Configuration bit.
With a 32 kHz input, the prescaler yields a nominal
WDT time-out period (TWDT) of 1 ms in 5-bit mode, or
4 ms in 7-bit mode.
A variable postscaler divides down the WDT prescaler
output and allows for a wide range of time-out periods.
The postscaler is controlled by the WDTPOST<3:0>
Configuration bits (FWDT<3:0>) which allow the selection of a total of 16 settings, from 1:1 to 1:32,768. Using
the prescaler and postscaler, time-out periods ranging
from 1 ms to 131 seconds can be achieved.
The WDT, prescaler and postscaler are reset:
• On any device Reset
• On the completion of a clock switch, whether
invoked by software (i.e., setting the OSWEN bit
after changing the NOSC bits) or by hardware
(i.e., Fail-Safe Clock Monitor)
• When a PWRSAV instruction is executed
(i.e., Sleep or Idle mode is entered)
• When the device exits Sleep or Idle mode to
resume normal operation
• By a CLRWDT instruction during normal execution
FIGURE 21-2:
If the WDT is enabled, it will continue to run during
Sleep or Idle modes. When the WDT time-out occurs,
the device will wake the device and code execution will
continue from where the PWRSAV instruction was executed. The corresponding SLEEP or IDLE bits
(RCON<3,2>) will need to be cleared in software after
the device wakes up.
The WDT flag bit, WDTO (RCON<4>), is not automatically
cleared following a WDT time-out. To detect subsequent
WDT events, the flag must be cleared in software.
Note:
The CLRWDT and PWRSAV instructions
clear the prescaler and postscaler counts
when executed.
The WDT is enabled or disabled by the FWDTEN
Configuration bit in the FWDT Configuration register.
When the FWDTEN Configuration bit is set, the WDT is
always enabled.
The WDT can be optionally controlled in software when
the FWDTEN Configuration bit has been programmed
to ‘0’. The WDT is enabled in software by setting the
SWDTEN control bit (RCON<5>). The SWDTEN control bit is cleared on any device Reset. The software
WDT option allows the user to enable the WDT for critical code segments and disable the WDT during
non-critical segments for maximum power savings.
Note:
If the WINDIS bit (FWDT<6>) is cleared, the
CLRWDT instruction should be executed by
the application software only during the last
1/4 of the WDT period. This CLRWDT window can be determined by using a timer. If
a CLRWDT instruction is executed before
this window, a WDT Reset occurs.
WDT BLOCK DIAGRAM
All Device Resets
Transition to New Clock Source
Exit Sleep or Idle Mode
PWRSAV Instruction
CLRWDT Instruction
Watchdog Timer
Sleep/Idle
WDTPRE
WDTPOST<3:0>
WDT
Wake-up
SWDTEN
FWDTEN
RS
Prescaler
(divide by N1)
LPRC Clock
1
RS
Postscaler
(divide by N2)
0
WINDIS
WDT
Reset
WDT Window Select
CLRWDT Instruction
 2009 Microchip Technology Inc.
Preliminary
DS70592B-page 225
PIC24HJXXXGPX06A/X08A/X10A
21.5
JTAG Interface
21.7
PIC24HJXXXGPX06A/X08A/X10A devices implement
a JTAG interface, which supports boundary scan
device testing, as well as in-circuit programming.
Detailed information on the interface will be provided in
future revisions of the document.
Note:
21.6
For further information, refer to the
dsPIC33F/PIC24H Family Reference
Manual“, Section 24. “Programming
and Diagnostics” (DS70246), which is
available from the Microchip website
(www.microchip.com).
Code Protection and
CodeGuard™ Security
The PIC24H product families offer advanced implementation of CodeGuard™ Security. CodeGuard
Security enables multiple parties to securely share
resources (memory, interrupts and peripherals) on a
single chip. This feature helps protect individual
Intellectual Property in collaborative system designs.
When coupled with software encryption libraries,
CodeGuard Security can be used to securely update
Flash even when multiple IP are resident on the single
chip. The code protection features vary depending on
the actual PIC24H implemented. The following
sections provide an overview these features.
The code protection features are controlled by the
Configuration registers: FBS, FSS and FGS.
Note:
For further information, refer to the
“dsPIC33F/PIC24H Family Reference
Manual”, Section 23. “CodeGuard™
Security” (DS70239), which is available
from the Microchip website (www.microchip.com).
DS70592B-page 226
In-Circuit Serial Programming
Programming Capability
PIC24HJXXXGPX06A/X08A/X10A family digital signal
controllers can be serially programmed while in the end
application circuit. This is simply done with two lines for
clock and data and three other lines for power, ground
and the programming sequence. This allows customers to manufacture boards with unprogrammed
devices and then program the digital signal controller
just before shipping the product. This also allows the
most recent firmware or a custom firmware, to be programmed. Please refer to the “dsPIC33F/PIC24H
Flash
Programming
Specification”
(DS70152)
document for details about ICSP programming
capability.
Any one out of three pairs of programming clock/data
pins may be used:
• PGEC1 and PGED1
• PGEC2 and PGED2
• PGEC3 and PGED3
21.8
In-Circuit Debugger
When MPLAB® ICD 2 is selected as a debugger, the
in-circuit debugging functionality is enabled. This function allows simple debugging functions when used with
MPLAB IDE. Debugging functionality is controlled
through the PGECx (Emulation/Debug Clock) and
PGEDx (Emulation/Debug Data) pin functions.
Any one out of three pairs of debugging clock/data pins
may be used:
• PGEC1 and PGED1
• PGEC2 and PGED2
• PGEC3 and PGED3
To use the in-circuit debugger function of the device,
the design must implement ICSP programming capability connections to MCLR, VDD, VSS and the PGEDx/
PGECx pin pair. In addition, when the feature is
enabled, some of the resources are not available for
general use. These resources include the first 80 bytes
of data RAM and two I/O pins.
Preliminary
 2009 Microchip Technology Inc.
PIC24HJXXXGPX06A/X08A/X10A
22.0
Note:
INSTRUCTION SET SUMMARY
This data sheet summarizes the features
of the PIC24HJXXXGPX06A/X08A/X10A
families of devices. However, it is not
intended to be a comprehensive reference
source. To complement the information in
this data sheet, refer to the related section
in
the
“dsPIC33F/PIC24H
Family
Reference Manual”, which is available
from
the
Microchip
website
(www.microchip.com).
The PIC24H instruction set is identical to that of the
PIC24F, and is a subset of the dsPIC30F/33F
instruction set.
Most instructions are a single program memory word
(24 bits). Only three instructions require two program
memory locations.
Each single-word instruction is a 24-bit word, divided
into an 8-bit opcode, which specifies the instruction
type and one or more operands, which further specify
the operation of the instruction.
The instruction set is highly orthogonal and is grouped
into five basic categories:
•
•
•
•
•
Most bit-oriented instructions (including simple
rotate/shift instructions) have two operands:
• The W register (with or without an address
modifier) or file register (specified by the value of
‘Ws’ or ‘f’)
• The bit in the W register or file register
(specified by a literal value or indirectly by the
contents of register ‘Wb’)
The literal instructions that involve data movement may
use some of the following operands:
• A literal value to be loaded into a W register or file
register (specified by the value of ‘k’)
• The W register or file register where the literal
value is to be loaded (specified by ‘Wb’ or ‘f’)
However, literal instructions that involve arithmetic or
logical operations use some of the following operands:
• The first source operand which is a register ‘Wb’
without any address modifier
• The second source operand which is a literal
value
• The destination of the result (only if not the same
as the first source operand) which is typically a
register ‘Wd’ with or without an address modifier
The control instructions may use some of the following
operands:
Word or byte-oriented operations
Bit-oriented operations
Literal operations
DSP operations
Control operations
• A program memory address
• The mode of the table read and table write
instructions
Table 22-1 shows the general symbols used in
describing the instructions.
The PIC24H instruction set summary in Table 22-2 lists
all the instructions, along with the status flags affected
by each instruction.
Most word or byte-oriented W register instructions
(including barrel shift instructions) have three
operands:
• The first source operand which is typically a
register ‘Wb’ without any address modifier
• The second source operand which is typically a
register ‘Ws’ with or without an address modifier
• The destination of the result which is typically a
register ‘Wd’ with or without an address modifier
However, word or byte-oriented file register instructions
have two operands:
• The file register specified by the value ‘f’
• The destination, which could either be the file
register ‘f’ or the W0 register, which is denoted as
‘WREG’
All instructions are a single word, except for certain
double word instructions, which were made double
word instructions so that all the required information is
available in these 48 bits. In the second word, the
8 MSbs are ‘0’s. If this second word is executed as an
instruction (by itself), it will execute as a NOP.
Most single-word instructions are executed in a single
instruction cycle, unless a conditional test is true, or the
program counter is changed as a result of the instruction. In these cases, the execution takes two instruction
cycles with the additional instruction cycle(s) executed
as a NOP. Notable exceptions are the BRA (unconditional/computed branch), indirect CALL/GOTO, all table
reads and writes and RETURN/RETFIE instructions,
which are single-word instructions but take two or three
cycles. Certain instructions that involve skipping over the
subsequent instruction require either two or three cycles
if the skip is performed, depending on whether the
instruction being skipped is a single-word or double word
instruction. Moreover, double word moves require two
cycles. The double word instructions execute in two
instruction cycles.
Note:
 2009 Microchip Technology Inc.
Preliminary
For more details on the instruction set,
refer to the “dsPIC30F/33F Programmer’s
Reference Manual” (DS70157).
DS70592B-page 227
PIC24HJXXXGPX06A/X08A/X10A
TABLE 22-1:
SYMBOLS USED IN OPCODE DESCRIPTIONS
Field
#text
Description
Means literal defined by “text”
(text)
Means “content of text”
[text]
Means “the location addressed by text”
{ }
Optional field or operation
<n:m>
Register bit field
.b
Byte mode selection
.d
Double Word mode selection
.S
Shadow register select
.w
Word mode selection (default)
bit4
4-bit bit selection field (used in word addressed instructions) {0...15}
C, DC, N, OV, Z
MCU Status bits: Carry, Digit Carry, Negative, Overflow, Sticky Zero
Expr
Absolute address, label or expression (resolved by the linker)
f
File register address {0x0000...0x1FFF}
lit1
1-bit unsigned literal {0,1}
lit4
4-bit unsigned literal {0...15}
lit5
5-bit unsigned literal {0...31}
lit8
8-bit unsigned literal {0...255}
lit10
10-bit unsigned literal {0...255} for Byte mode, {0:1023} for Word mode
lit14
14-bit unsigned literal {0...16384}
lit16
16-bit unsigned literal {0...65535}
lit23
23-bit unsigned literal {0...8388608}; LSB must be ‘0’
None
Field does not require an entry, may be blank
PC
Program Counter
Slit10
10-bit signed literal {-512...511}
Slit16
16-bit signed literal {-32768...32767}
Slit6
6-bit signed literal {-16...16}
Wb
Base W register {W0..W15}
Wd
Destination W register { Wd, [Wd], [Wd++], [Wd--], [++Wd], [--Wd] }
Wdo
Destination W register 
{ Wnd, [Wnd], [Wnd++], [Wnd--], [++Wnd], [--Wnd], [Wnd+Wb] }
Wm,Wn
Dividend, Divisor working register pair (direct addressing)
Wm*Wm
Multiplicand and Multiplier working register pair for Square instructions 
{W4 * W4,W5 * W5,W6 * W6,W7 * W7}
Wm*Wn
Multiplicand and Multiplier working register pair for DSP instructions 
{W4 * W5,W4 * W6,W4 * W7,W5 * W6,W5 * W7,W6 * W7}
Wn
One of 16 working registers {W0..W15}
Wnd
One of 16 destination working registers {W0...W15}
Wns
One of 16 source working registers {W0...W15}
WREG
W0 (working register used in file register instructions)
Ws
Source W register { Ws, [Ws], [Ws++], [Ws--], [++Ws], [--Ws] }
Wso
Source W register 
{ Wns, [Wns], [Wns++], [Wns--], [++Wns], [--Wns], [Wns+Wb] }
DS70592B-page 228
Preliminary
 2009 Microchip Technology Inc.
PIC24HJXXXGPX06A/X08A/X10A
TABLE 22-2:
Base
Instr
#
1
INSTRUCTION SET OVERVIEW
Assembly
Mnemonic
ADD
Assembly Syntax
3
4
5
6
7
8
9
10
11
ADDC
AND
ASR
BCLR
BRA
BSET
BSW
BTG
BTSC
BTSS
# of
# of
Words Cycles
Status Flags
Affected
f = f + WREG
1
1
C,DC,N,OV,Z
f,WREG
WREG = f + WREG
1
1
C,DC,N,OV,Z
ADD
#lit10,Wn
Wd = lit10 + Wd
1
1
C,DC,N,OV,Z
ADD
Wb,Ws,Wd
Wd = Wb + Ws
1
1
C,DC,N,OV,Z
ADD
Wb,#lit5,Wd
Wd = Wb + lit5
1
1
C,DC,N,OV,Z
ADDC
f
f = f + WREG + (C)
1
1
C,DC,N,OV,Z
ADDC
f,WREG
WREG = f + WREG + (C)
1
1
C,DC,N,OV,Z
ADDC
#lit10,Wn
Wd = lit10 + Wd + (C)
1
1
C,DC,N,OV,Z
ADDC
Wb,Ws,Wd
Wd = Wb + Ws + (C)
1
1
C,DC,N,OV,Z
C,DC,N,OV,Z
ADD
ADD
2
Description
f
ADDC
Wb,#lit5,Wd
Wd = Wb + lit5 + (C)
1
1
AND
f
f = f .AND. WREG
1
1
N,Z
AND
f,WREG
WREG = f .AND. WREG
1
1
N,Z
AND
#lit10,Wn
Wd = lit10 .AND. Wd
1
1
N,Z
AND
Wb,Ws,Wd
Wd = Wb .AND. Ws
1
1
N,Z
AND
Wb,#lit5,Wd
Wd = Wb .AND. lit5
1
1
N,Z
ASR
f
f = Arithmetic Right Shift f
1
1
C,N,OV,Z
ASR
f,WREG
WREG = Arithmetic Right Shift f
1
1
C,N,OV,Z
ASR
Ws,Wd
Wd = Arithmetic Right Shift Ws
1
1
C,N,OV,Z
ASR
Wb,Wns,Wnd
Wnd = Arithmetic Right Shift Wb by Wns
1
1
N,Z
ASR
Wb,#lit5,Wnd
Wnd = Arithmetic Right Shift Wb by lit5
1
1
N,Z
BCLR
f,#bit4
Bit Clear f
1
1
None
BCLR
Ws,#bit4
Bit Clear Ws
1
1
None
BRA
C,Expr
Branch if Carry
1
1 (2)
None
BRA
GE,Expr
Branch if greater than or equal
1
1 (2)
None
BRA
GEU,Expr
Branch if unsigned greater than or equal
1
1 (2)
None
BRA
GT,Expr
Branch if greater than
1
1 (2)
None
BRA
GTU,Expr
Branch if unsigned greater than
1
1 (2)
None
BRA
LE,Expr
Branch if less than or equal
1
1 (2)
None
BRA
LEU,Expr
Branch if unsigned less than or equal
1
1 (2)
None
BRA
LT,Expr
Branch if less than
1
1 (2)
None
BRA
LTU,Expr
Branch if unsigned less than
1
1 (2)
None
BRA
N,Expr
Branch if Negative
1
1 (2)
None
BRA
NC,Expr
Branch if Not Carry
1
1 (2)
None
BRA
NN,Expr
Branch if Not Negative
1
1 (2)
None
BRA
NZ,Expr
Branch if Not Zero
1
1 (2)
None
BRA
Expr
Branch Unconditionally
1
2
None
BRA
Z,Expr
Branch if Zero
1
1 (2)
None
BRA
Wn
Computed Branch
1
2
None
BSET
f,#bit4
Bit Set f
1
1
None
BSET
Ws,#bit4
Bit Set Ws
1
1
None
BSW.C
Ws,Wb
Write C bit to Ws<Wb>
1
1
None
BSW.Z
Ws,Wb
Write Z bit to Ws<Wb>
1
1
None
BTG
f,#bit4
Bit Toggle f
1
1
None
BTG
Ws,#bit4
Bit Toggle Ws
1
1
None
BTSC
f,#bit4
Bit Test f, Skip if Clear
1
1
(2 or 3)
None
BTSC
Ws,#bit4
Bit Test Ws, Skip if Clear
1
1
(2 or 3)
None
BTSS
f,#bit4
Bit Test f, Skip if Set
1
1
(2 or 3)
None
BTSS
Ws,#bit4
Bit Test Ws, Skip if Set
1
1
(2 or 3)
None
 2009 Microchip Technology Inc.
Preliminary
DS70592B-page 229
PIC24HJXXXGPX06A/X08A/X10A
TABLE 22-2:
Base
Instr
#
12
13
INSTRUCTION SET OVERVIEW (CONTINUED)
Assembly
Mnemonic
BTST
BTSTS
Assembly Syntax
Description
# of
# of
Words Cycles
Status Flags
Affected
BTST
f,#bit4
Bit Test f
1
1
Z
BTST.C
Ws,#bit4
Bit Test Ws to C
1
1
C
BTST.Z
Ws,#bit4
Bit Test Ws to Z
1
1
Z
BTST.C
Ws,Wb
Bit Test Ws<Wb> to C
1
1
C
BTST.Z
Ws,Wb
Bit Test Ws<Wb> to Z
1
1
Z
BTSTS
f,#bit4
Bit Test then Set f
1
1
Z
BTSTS.C
Ws,#bit4
Bit Test Ws to C, then Set
1
1
C
BTSTS.Z
Ws,#bit4
Bit Test Ws to Z, then Set
1
1
Z
lit23
Call subroutine
2
2
None
14
CALL
CALL
CALL
Wn
Call indirect subroutine
1
2
None
15
CLR
CLR
f
f = 0x0000
1
1
None
CLR
WREG
WREG = 0x0000
1
1
None
CLR
Ws
Ws = 0x0000
1
1
None
16
CLRWDT
CLRWDT
Clear Watchdog Timer
1
1
WDTO,Sleep
17
COM
COM
f
f=f
1
1
N,Z
COM
f,WREG
WREG = f
1
1
N,Z
18
19
20
CP
CP0
CPB
COM
Ws,Wd
Wd = Ws
1
1
N,Z
CP
f
Compare f with WREG
1
1
C,DC,N,OV,Z
CP
Wb,#lit5
Compare Wb with lit5
1
1
C,DC,N,OV,Z
CP
Wb,Ws
Compare Wb with Ws (Wb – Ws)
1
1
C,DC,N,OV,Z
CP0
f
Compare f with 0x0000
1
1
C,DC,N,OV,Z
CP0
Ws
Compare Ws with 0x0000
1
1
C,DC,N,OV,Z
CPB
f
Compare f with WREG, with Borrow
1
1
C,DC,N,OV,Z
CPB
Wb,#lit5
Compare Wb with lit5, with Borrow
1
1
C,DC,N,OV,Z
CPB
Wb,Ws
Compare Wb with Ws, with Borrow
(Wb – Ws – C)
1
1
C,DC,N,OV,Z
21
CPSEQ
CPSEQ
Wb, Wn
Compare Wb with Wn, skip if =
1
1
(2 or 3)
None
22
CPSGT
CPSGT
Wb, Wn
Compare Wb with Wn, skip if >
1
1
(2 or 3)
None
23
CPSLT
CPSLT
Wb, Wn
Compare Wb with Wn, skip if <
1
1
(2 or 3)
None
24
CPSNE
CPSNE
Wb, Wn
Compare Wb with Wn, skip if 
1
1
(2 or 3)
None
25
DAW
DAW
Wn
Wn = decimal adjust Wn
1
1
C
26
DEC
DEC
f
f=f–1
1
1
C,DC,N,OV,Z
DEC
f,WREG
WREG = f – 1
1
1
C,DC,N,OV,Z
DEC
Ws,Wd
Wd = Ws – 1
1
1
C,DC,N,OV,Z
DEC2
f
f=f–2
1
1
C,DC,N,OV,Z
DEC2
f,WREG
WREG = f – 2
1
1
C,DC,N,OV,Z
C,DC,N,OV,Z
27
DEC2
DEC2
Ws,Wd
Wd = Ws – 2
1
1
28
DISI
DISI
#lit14
Disable Interrupts for k instruction cycles
1
1
None
29
DIV
DIV.S
Wm,Wn
Signed 16/16-bit Integer Divide
1
18
N,Z,C,OV
DIV.SD
Wm,Wn
Signed 32/16-bit Integer Divide
1
18
N,Z,C,OV
DIV.U
Wm,Wn
Unsigned 16/16-bit Integer Divide
1
18
N,Z,C,OV
DIV.UD
Wm,Wn
Unsigned 32/16-bit Integer Divide
1
18
N,Z,C,OV
30
EXCH
EXCH
Wns,Wnd
Swap Wns with Wnd
1
1
None
31
FBCL
FBCL
Ws,Wnd
Find Bit Change from Left (MSb) Side
1
1
C
32
FF1L
FF1L
Ws,Wnd
Find First One from Left (MSb) Side
1
1
C
33
FF1R
FF1R
Ws,Wnd
Find First One from Right (LSb) Side
1
1
C
34
GOTO
GOTO
Expr
Go to address
2
2
None
GOTO
Wn
Go to indirect
1
2
None
DS70592B-page 230
Preliminary
 2009 Microchip Technology Inc.
PIC24HJXXXGPX06A/X08A/X10A
TABLE 22-2:
Base
Instr
#
35
36
37
INSTRUCTION SET OVERVIEW (CONTINUED)
Assembly
Mnemonic
INC
INC2
IOR
Assembly Syntax
Description
# of
# of
Words Cycles
Status Flags
Affected
INC
f
f=f+1
1
1
C,DC,N,OV,Z
INC
f,WREG
WREG = f + 1
1
1
C,DC,N,OV,Z
C,DC,N,OV,Z
INC
Ws,Wd
Wd = Ws + 1
1
1
INC2
f
f=f+2
1
1
C,DC,N,OV,Z
INC2
f,WREG
WREG = f + 2
1
1
C,DC,N,OV,Z
C,DC,N,OV,Z
INC2
Ws,Wd
Wd = Ws + 2
1
1
IOR
f
f = f .IOR. WREG
1
1
N,Z
IOR
f,WREG
WREG = f .IOR. WREG
1
1
N,Z
IOR
#lit10,Wn
Wd = lit10 .IOR. Wd
1
1
N,Z
IOR
Wb,Ws,Wd
Wd = Wb .IOR. Ws
1
1
N,Z
IOR
Wb,#lit5,Wd
Wd = Wb .IOR. lit5
1
1
N,Z
38
LNK
LNK
#lit14
Link Frame Pointer
1
1
None
39
LSR
LSR
f
f = Logical Right Shift f
1
1
C,N,OV,Z
LSR
f,WREG
WREG = Logical Right Shift f
1
1
C,N,OV,Z
LSR
Ws,Wd
Wd = Logical Right Shift Ws
1
1
C,N,OV,Z
LSR
Wb,Wns,Wnd
Wnd = Logical Right Shift Wb by Wns
1
1
N,Z
LSR
Wb,#lit5,Wnd
Wnd = Logical Right Shift Wb by lit5
1
1
N,Z
MOV
f,Wn
Move f to Wn
1
1
None
MOV
f
Move f to f
1
1
N,Z
MOV
f,WREG
Move f to WREG
1
1
N,Z
MOV
#lit16,Wn
Move 16-bit literal to Wn
1
1
None
MOV.b
#lit8,Wn
Move 8-bit literal to Wn
1
1
None
MOV
Wn,f
Move Wn to f
1
1
None
MOV
Wso,Wdo
Move Ws to Wd
1
1
None
MOV
WREG,f
Move WREG to f
1
1
N,Z
Move Double from W(ns):W(ns + 1) to Wd
1
2
None
None
40
MOV
MOV.D
Wns,Wd
Move Double from Ws to W(nd + 1):W(nd)
1
2
MUL.SS
Wb,Ws,Wnd
{Wnd + 1, Wnd} = signed(Wb) * signed(Ws)
1
1
None
MUL.SU
Wb,Ws,Wnd
{Wnd + 1, Wnd} = signed(Wb) * unsigned(Ws)
1
1
None
MUL.US
Wb,Ws,Wnd
{Wnd + 1, Wnd} = unsigned(Wb) * signed(Ws)
1
1
None
MUL.UU
Wb,Ws,Wnd
{Wnd + 1, Wnd} = unsigned(Wb) *
unsigned(Ws)
1
1
None
MUL.SU
Wb,#lit5,Wnd
{Wnd + 1, Wnd} = signed(Wb) * unsigned(lit5)
1
1
None
MUL.UU
Wb,#lit5,Wnd
{Wnd + 1, Wnd} = unsigned(Wb) *
unsigned(lit5)
1
1
None
MUL
f
W3:W2 = f * WREG
1
1
None
NEG
f
f=f+1
1
1
C,DC,N,OV,Z
NEG
f,WREG
WREG = f + 1
1
1
C,DC,N,OV,Z
NEG
Ws,Wd
Wd = Ws + 1
1
1
C,DC,N,OV,Z
NOP
No Operation
1
1
None
NOPR
No Operation
1
1
None
None
MOV.D
41
42
43
44
MUL
NEG
NOP
POP
Ws,Wnd
POP
f
Pop f from Top-of-Stack (TOS)
1
1
POP
Wdo
Pop from Top-of-Stack (TOS) to Wdo
1
1
None
POP.D
Wnd
Pop from Top-of-Stack (TOS) to
W(nd):W(nd + 1)
1
2
None
Pop Shadow Registers
1
1
All
f
Push f to Top-of-Stack (TOS)
1
1
None
PUSH
Wso
Push Wso to Top-of-Stack (TOS)
1
1
None
PUSH.D
Wns
Push W(ns):W(ns + 1) to Top-of-Stack (TOS)
1
2
None
Push Shadow Registers
1
1
None
Go into Sleep or Idle mode
1
1
WDTO,Sleep
POP.S
45
PUSH
PUSH
PUSH.S
46
PWRSAV
PWRSAV
#lit1
 2009 Microchip Technology Inc.
Preliminary
DS70592B-page 231
PIC24HJXXXGPX06A/X08A/X10A
TABLE 22-2:
Base
Instr
#
47
48
INSTRUCTION SET OVERVIEW (CONTINUED)
Assembly
Mnemonic
RCALL
REPEAT
Assembly Syntax
Description
# of
# of
Words Cycles
Status Flags
Affected
RCALL
Expr
Relative Call
1
2
None
RCALL
Wn
Computed Call
1
2
None
REPEAT
#lit14
Repeat Next Instruction lit14 + 1 times
1
1
None
REPEAT
Wn
Repeat Next Instruction (Wn) + 1 times
1
1
None
None
49
RESET
RESET
Software device Reset
1
1
50
RETFIE
RETFIE
Return from interrupt
1
3 (2)
None
51
RETLW
RETLW
Return with literal in Wn
1
3 (2)
None
52
RETURN
RETURN
Return from Subroutine
1
3 (2)
None
53
RLC
RLC
f
f = Rotate Left through Carry f
1
1
C,N,Z
RLC
f,WREG
WREG = Rotate Left through Carry f
1
1
C,N,Z
RLC
Ws,Wd
Wd = Rotate Left through Carry Ws
1
1
C,N,Z
RLNC
f
f = Rotate Left (No Carry) f
1
1
N,Z
RLNC
f,WREG
WREG = Rotate Left (No Carry) f
1
1
N,Z
54
55
56
RLNC
RRC
RRNC
#lit10,Wn
RLNC
Ws,Wd
Wd = Rotate Left (No Carry) Ws
1
1
N,Z
RRC
f
f = Rotate Right through Carry f
1
1
C,N,Z
RRC
f,WREG
WREG = Rotate Right through Carry f
1
1
C,N,Z
RRC
Ws,Wd
Wd = Rotate Right through Carry Ws
1
1
C,N,Z
RRNC
f
f = Rotate Right (No Carry) f
1
1
N,Z
RRNC
f,WREG
WREG = Rotate Right (No Carry) f
1
1
N,Z
RRNC
Ws,Wd
Wd = Rotate Right (No Carry) Ws
1
1
N,Z
57
SE
SE
Ws,Wnd
Wnd = sign-extended Ws
1
1
C,N,Z
58
SETM
SETM
f
f = 0xFFFF
1
1
None
SETM
WREG
WREG = 0xFFFF
1
1
None
SETM
Ws
Ws = 0xFFFF
1
1
None
SL
f
f = Left Shift f
1
1
C,N,OV,Z
SL
f,WREG
WREG = Left Shift f
1
1
C,N,OV,Z
SL
Ws,Wd
Wd = Left Shift Ws
1
1
C,N,OV,Z
SL
Wb,Wns,Wnd
Wnd = Left Shift Wb by Wns
1
1
N,Z
SL
Wb,#lit5,Wnd
Wnd = Left Shift Wb by lit5
1
1
N,Z
SUB
f
f = f – WREG
1
1
C,DC,N,OV,Z
SUB
f,WREG
WREG = f – WREG
1
1
C,DC,N,OV,Z
SUB
#lit10,Wn
Wn = Wn – lit10
1
1
C,DC,N,OV,Z
SUB
Wb,Ws,Wd
Wd = Wb – Ws
1
1
C,DC,N,OV,Z
SUB
Wb,#lit5,Wd
Wd = Wb – lit5
1
1
C,DC,N,OV,Z
SUBB
f
f = f – WREG – (C)
1
1
C,DC,N,OV,Z
59
60
61
62
63
64
65
SL
SUB
SUBB
SUBR
SUBBR
SWAP
TBLRDH
SUBB
f,WREG
WREG = f – WREG – (C)
1
1
C,DC,N,OV,Z
SUBB
#lit10,Wn
Wn = Wn – lit10 – (C)
1
1
C,DC,N,OV,Z
SUBB
Wb,Ws,Wd
Wd = Wb – Ws – (C)
1
1
C,DC,N,OV,Z
SUBB
Wb,#lit5,Wd
Wd = Wb – lit5 – (C)
1
1
SUBR
f
f = WREG – f
1
1
C,DC,N,OV,Z
SUBR
f,WREG
WREG = WREG – f
1
1
C,DC,N,OV,Z
SUBR
Wb,Ws,Wd
Wd = Ws – Wb
1
1
C,DC,N,OV,Z
SUBR
Wb,#lit5,Wd
Wd = lit5 – Wb
1
1
C,DC,N,OV,Z
SUBBR
f
f = WREG – f – (C)
1
1
C,DC,N,OV,Z
SUBBR
f,WREG
WREG = WREG – f – (C)
1
1
C,DC,N,OV,Z
SUBBR
Wb,Ws,Wd
Wd = Ws – Wb – (C)
1
1
C,DC,N,OV,Z
C,DC,N,OV,Z
C,DC,N,OV,Z
SUBBR
Wb,#lit5,Wd
Wd = lit5 – Wb – (C)
1
1
SWAP.b
Wn
Wn = nibble swap Wn
1
1
None
SWAP
Wn
Wn = byte swap Wn
1
1
None
TBLRDH
Ws,Wd
Read Prog<23:16> to Wd<7:0>
1
2
None
DS70592B-page 232
Preliminary
 2009 Microchip Technology Inc.
PIC24HJXXXGPX06A/X08A/X10A
TABLE 22-2:
Base
Instr
#
INSTRUCTION SET OVERVIEW (CONTINUED)
Assembly
Mnemonic
Assembly Syntax
Description
# of
# of
Words Cycles
Status Flags
Affected
66
TBLRDL
TBLRDL
Ws,Wd
Read Prog<15:0> to Wd
1
2
None
67
TBLWTH
TBLWTH
Ws,Wd
Write Ws<7:0> to Prog<23:16>
1
2
None
Ws,Wd
Write Ws to Prog<15:0>
1
2
None
Unlink Frame Pointer
1
1
None
68
TBLWTL
TBLWTL
69
ULNK
ULNK
70
XOR
XOR
f
f = f .XOR. WREG
1
1
N,Z
XOR
f,WREG
WREG = f .XOR. WREG
1
1
N,Z
XOR
#lit10,Wn
Wd = lit10 .XOR. Wd
1
1
N,Z
XOR
Wb,Ws,Wd
Wd = Wb .XOR. Ws
1
1
N,Z
XOR
Wb,#lit5,Wd
Wd = Wb .XOR. lit5
1
1
N,Z
ZE
Ws,Wnd
Wnd = Zero-extend Ws
1
1
C,Z,N
71
ZE
 2009 Microchip Technology Inc.
Preliminary
DS70592B-page 233
PIC24HJXXXGPX06A/X08A/X10A
NOTES:
DS70592B-page 234
Preliminary
 2009 Microchip Technology Inc.
PIC24HJXXXGPX06A/X08A/X10A
23.0
DEVELOPMENT SUPPORT
23.1
The PIC® microcontrollers and dsPIC® digital signal
controllers are supported with a full range of software
and hardware development tools:
• Integrated Development Environment
- MPLAB® IDE Software
• Compilers/Assemblers/Linkers
- MPLAB C Compiler for Various Device
Families
- HI-TECH C for Various Device Families
- MPASMTM Assembler
- MPLINKTM Object Linker/
MPLIBTM Object Librarian
- MPLAB Assembler/Linker/Librarian for
Various Device Families
• Simulators
- MPLAB SIM Software Simulator
• Emulators
- MPLAB REAL ICE™ In-Circuit Emulator
• In-Circuit Debuggers
- MPLAB ICD 3
- PICkit™ 3 Debug Express
• Device Programmers
- PICkit™ 2 Programmer
- MPLAB PM3 Device Programmer
• Low-Cost Demonstration/Development Boards,
Evaluation Kits, and Starter Kits
MPLAB Integrated Development
Environment Software
The MPLAB IDE software brings an ease of software
development previously unseen in the 8/16/32-bit
microcontroller market. The MPLAB IDE is a Windows®
operating system-based application that contains:
• A single graphical interface to all debugging tools
- Simulator
- Programmer (sold separately)
- In-Circuit Emulator (sold separately)
- In-Circuit Debugger (sold separately)
• A full-featured editor with color-coded context
• A multiple project manager
• Customizable data windows with direct edit of
contents
• High-level source code debugging
• Mouse over variable inspection
• Drag and drop variables from source to watch
windows
• Extensive on-line help
• Integration of select third party tools, such as
IAR C Compilers
The MPLAB IDE allows you to:
• Edit your source files (either C or assembly)
• One-touch compile or assemble, and download to
emulator and simulator tools (automatically
updates all project information)
• Debug using:
- Source files (C or assembly)
- Mixed C and assembly
- Machine code
MPLAB IDE supports multiple debugging tools in a
single development paradigm, from the cost-effective
simulators, through low-cost in-circuit debuggers, to
full-featured emulators. This eliminates the learning
curve when upgrading to tools with increased flexibility
and power.
 2009 Microchip Technology Inc.
Preliminary
DS70592B-page 235
PIC24HJXXXGPX06A/X08A/X10A
23.2
MPLAB C Compilers for Various
Device Families
The MPLAB C Compiler code development systems
are complete ANSI C compilers for Microchip’s PIC18,
PIC24 and PIC32 families of microcontrollers and the
dsPIC30 and dsPIC33 families of digital signal controllers. These compilers provide powerful integration
capabilities, superior code optimization and ease of
use.
For easy source level debugging, the compilers provide
symbol information that is optimized to the MPLAB IDE
debugger.
23.3
HI-TECH C for Various Device
Families
For easy source level debugging, the compilers provide
symbol information that is optimized to the MPLAB IDE
debugger.
The compilers include a macro assembler, linker, preprocessor, and one-step driver, and can run on multiple
platforms.
MPASM Assembler
The MPASM Assembler is a full-featured, universal
macro assembler for PIC10/12/16/18 MCUs.
The MPASM Assembler generates relocatable object
files for the MPLINK Object Linker, Intel® standard HEX
files, MAP files to detail memory usage and symbol
reference, absolute LST files that contain source lines
and generated machine code and COFF files for
debugging.
The MPASM Assembler features include:
MPLINK Object Linker/
MPLIB Object Librarian
The MPLINK Object Linker combines relocatable
objects created by the MPASM Assembler and the
MPLAB C18 C Compiler. It can link relocatable objects
from precompiled libraries, using directives from a
linker script.
The MPLIB Object Librarian manages the creation and
modification of library files of precompiled code. When
a routine from a library is called from a source file, only
the modules that contain that routine will be linked in
with the application. This allows large libraries to be
used efficiently in many different applications.
The object linker/library features include:
The HI-TECH C Compiler code development systems
are complete ANSI C compilers for Microchip’s PIC
family of microcontrollers and the dsPIC family of digital
signal controllers. These compilers provide powerful
integration capabilities, omniscient code generation
and ease of use.
23.4
23.5
• Efficient linking of single libraries instead of many
smaller files
• Enhanced code maintainability by grouping
related modules together
• Flexible creation of libraries with easy module
listing, replacement, deletion and extraction
23.6
MPLAB Assembler, Linker and
Librarian for Various Device
Families
MPLAB Assembler produces relocatable machine
code from symbolic assembly language for PIC24,
PIC32 and dsPIC devices. MPLAB C Compiler uses
the assembler to produce its object file. The assembler
generates relocatable object files that can then be
archived or linked with other relocatable object files and
archives to create an executable file. Notable features
of the assembler include:
•
•
•
•
•
•
Support for the entire device instruction set
Support for fixed-point and floating-point data
Command line interface
Rich directive set
Flexible macro language
MPLAB IDE compatibility
• Integration into MPLAB IDE projects
• User-defined macros to streamline
assembly code
• Conditional assembly for multi-purpose
source files
• Directives that allow complete control over the
assembly process
DS70592B-page 236
Preliminary
 2009 Microchip Technology Inc.
PIC24HJXXXGPX06A/X08A/X10A
23.7
MPLAB SIM Software Simulator
23.9
The MPLAB SIM Software Simulator allows code
development in a PC-hosted environment by simulating the PIC MCUs and dsPIC® DSCs on an instruction
level. On any given instruction, the data areas can be
examined or modified and stimuli can be applied from
a comprehensive stimulus controller. Registers can be
logged to files for further run-time analysis. The trace
buffer and logic analyzer display extend the power of
the simulator to record and track program execution,
actions on I/O, most peripherals and internal registers.
The MPLAB SIM Software Simulator fully supports
symbolic debugging using the MPLAB C Compilers,
and the MPASM and MPLAB Assemblers. The software simulator offers the flexibility to develop and
debug code outside of the hardware laboratory environment, making it an excellent, economical software
development tool.
23.8
MPLAB REAL ICE In-Circuit
Emulator System
MPLAB REAL ICE In-Circuit Emulator System is
Microchip’s next generation high-speed emulator for
Microchip Flash DSC and MCU devices. It debugs and
programs PIC® Flash MCUs and dsPIC® Flash DSCs
with the easy-to-use, powerful graphical user interface of
the MPLAB Integrated Development Environment (IDE),
included with each kit.
The emulator is connected to the design engineer’s PC
using a high-speed USB 2.0 interface and is connected
to the target with either a connector compatible with incircuit debugger systems (RJ11) or with the new highspeed, noise tolerant, Low-Voltage Differential Signal
(LVDS) interconnection (CAT5).
The emulator is field upgradable through future firmware
downloads in MPLAB IDE. In upcoming releases of
MPLAB IDE, new devices will be supported, and new
features will be added. MPLAB REAL ICE offers significant advantages over competitive emulators including
low-cost, full-speed emulation, run-time variable
watches, trace analysis, complex breakpoints, a ruggedized probe interface and long (up to three meters) interconnection cables.
 2009 Microchip Technology Inc.
MPLAB ICD 3 In-Circuit Debugger
System
MPLAB ICD 3 In-Circuit Debugger System is Microchip's most cost effective high-speed hardware
debugger/programmer for Microchip Flash Digital Signal Controller (DSC) and microcontroller (MCU)
devices. It debugs and programs PIC® Flash microcontrollers and dsPIC® DSCs with the powerful, yet easyto-use graphical user interface of MPLAB Integrated
Development Environment (IDE).
The MPLAB ICD 3 In-Circuit Debugger probe is connected to the design engineer's PC using a high-speed
USB 2.0 interface and is connected to the target with a
connector compatible with the MPLAB ICD 2 or MPLAB
REAL ICE systems (RJ-11). MPLAB ICD 3 supports all
MPLAB ICD 2 headers.
23.10 PICkit 3 In-Circuit Debugger/
Programmer and
PICkit 3 Debug Express
The MPLAB PICkit 3 allows debugging and programming of PIC® and dsPIC® Flash microcontrollers at a
most affordable price point using the powerful graphical
user interface of the MPLAB Integrated Development
Environment (IDE). The MPLAB PICkit 3 is connected
to the design engineer's PC using a full speed USB
interface and can be connected to the target via an
Microchip debug (RJ-11) connector (compatible with
MPLAB ICD 3 and MPLAB REAL ICE). The connector
uses two device I/O pins and the reset line to implement in-circuit debugging and In-Circuit Serial Programming™.
The PICkit 3 Debug Express include the PICkit 3, demo
board and microcontroller, hookup cables and CDROM
with user’s guide, lessons, tutorial, compiler and
MPLAB IDE software.
Preliminary
DS70592B-page 237
PIC24HJXXXGPX06A/X08A/X10A
23.11 PICkit 2 Development
Programmer/Debugger and
PICkit 2 Debug Express
23.13 Demonstration/Development
Boards, Evaluation Kits, and
Starter Kits
The PICkit™ 2 Development Programmer/Debugger is
a low-cost development tool with an easy to use interface for programming and debugging Microchip’s Flash
families of microcontrollers. The full featured
Windows® programming interface supports baseline
(PIC10F,
PIC12F5xx,
PIC16F5xx),
midrange
(PIC12F6xx, PIC16F), PIC18F, PIC24, dsPIC30,
dsPIC33, and PIC32 families of 8-bit, 16-bit, and 32-bit
microcontrollers, and many Microchip Serial EEPROM
products. With Microchip’s powerful MPLAB Integrated
Development Environment (IDE) the PICkit™ 2
enables in-circuit debugging on most PIC® microcontrollers. In-Circuit-Debugging runs, halts and single
steps the program while the PIC microcontroller is
embedded in the application. When halted at a breakpoint, the file registers can be examined and modified.
A wide variety of demonstration, development and
evaluation boards for various PIC MCUs and dsPIC
DSCs allows quick application development on fully functional systems. Most boards include prototyping areas for
adding custom circuitry and provide application firmware
and source code for examination and modification.
The PICkit 2 Debug Express include the PICkit 2, demo
board and microcontroller, hookup cables and CDROM
with user’s guide, lessons, tutorial, compiler and
MPLAB IDE software.
23.12 MPLAB PM3 Device Programmer
The MPLAB PM3 Device Programmer is a universal,
CE compliant device programmer with programmable
voltage verification at VDDMIN and VDDMAX for
maximum reliability. It features a large LCD display
(128 x 64) for menus and error messages and a modular, detachable socket assembly to support various
package types. The ICSP™ cable assembly is included
as a standard item. In Stand-Alone mode, the MPLAB
PM3 Device Programmer can read, verify and program
PIC devices without a PC connection. It can also set
code protection in this mode. The MPLAB PM3
connects to the host PC via an RS-232 or USB cable.
The MPLAB PM3 has high-speed communications and
optimized algorithms for quick programming of large
memory devices and incorporates an MMC card for file
storage and data applications.
DS70592B-page 238
The boards support a variety of features, including LEDs,
temperature sensors, switches, speakers, RS-232
interfaces, LCD displays, potentiometers and additional
EEPROM memory.
The demonstration and development boards can be
used in teaching environments, for prototyping custom
circuits and for learning about various microcontroller
applications.
In addition to the PICDEM™ and dsPICDEM™ demonstration/development board series of circuits, Microchip
has a line of evaluation kits and demonstration software
for analog filter design, KEELOQ® security ICs, CAN,
IrDA®, PowerSmart battery management, SEEVAL®
evaluation system, Sigma-Delta ADC, flow rate
sensing, plus many more.
Also available are starter kits that contain everything
needed to experience the specified device. This usually
includes a single application and debug capability, all
on one board.
Check the Microchip web page (www.microchip.com)
for the complete list of demonstration, development
and evaluation kits.
Preliminary
 2009 Microchip Technology Inc.
PIC24HJXXXGPX06A/X08A/X10A
24.0
ELECTRICAL CHARACTERISTICS
This section provides an overview of PIC24HJXXXGPX06A/X08A/X10A electrical characteristics. Additional information is provided in future revisions of this document as it becomes available.
Absolute maximum ratings for the PIC24HJXXXGPX06A/X08A/X10A family are listed below. Exposure to these maximum rating conditions for extended periods can affect device reliability. Functional operation of the device at these or
any other conditions above the parameters indicated in the operation listings of this specification is not implied.
Absolute Maximum Ratings(1)
Ambient temperature under bias.............................................................................................................-40°C to +125°C
Storage temperature .............................................................................................................................. -65°C to +150°C
Voltage on VDD with respect to VSS ......................................................................................................... -0.3V to +4.0V
Voltage on any pin that is not 5V tolerant with respect to VSS(4) .................................................... -0.3V to (VDD + 0.3V)
Voltage on any 5V tolerant pin with respect to VSS when VDD  3.0V(4) .................................................. -0.3V to +5.6V
Voltage on any 5V tolerant pin with respect to VSS when VDD < 3.0V(4) ........................................ -0.3V to (VDD + 0.3V)
Voltage on VCAP/VDDCORE with respect to VSS ....................................................................................... 2.25V to 2.75V
Maximum current out of VSS pin ...........................................................................................................................300 mA
Maximum current into VDD pin(2) ...........................................................................................................................250 mA
Maximum output current sunk by any I/O pin(3) ........................................................................................................4 mA
Maximum output current sourced by any I/O pin(3) ...................................................................................................4 mA
Maximum current sunk by all ports .......................................................................................................................200 mA
Maximum current sourced by all ports(2)...............................................................................................................200 mA
Note 1: Stresses above those listed under “Absolute Maximum Ratings” can cause permanent damage to the
device. This is a stress rating only, and functional operation of the device at those or any other conditions
above those indicated in the operation listings of this specification is not implied. Exposure to maximum
rating conditions for extended periods can affect device reliability.
2: Maximum allowable current is a function of device maximum power dissipation (see Table 24-2).
3: Exceptions are CLKOUT, which is able to sink/source 25 mA, and the VREF+, VREF-, SCLx, SDAx, PGECx
and PGEDx pins, which are able to sink/source 12 mA.
4: See the “Pin Diagrams” section for 5V tolerant pins.
 2009 Microchip Technology Inc.
Preliminary
DS70592B-page 239
PIC24HJXXXGPX06A/X08A/X10A
24.1
DC Characteristics
TABLE 24-1:
OPERATING MIPS VS. VOLTAGE
VDD Range
(in Volts)
Characteristic
TABLE 24-2:
Max MIPS
Temp Range
(in °C)
PIC24HJXXXGPX06A/X08A/X10A
3.0-3.6V
-40°C to +85°C
40
3.0-3.6V
-40°C to +125°C
40
THERMAL OPERATING CONDITIONS
Rating
Symbol
Min
Typ
Max
Unit
Operating Junction Temperature Range
TJ
-40
—
+125
°C
Operating Ambient Temperature Range
TA
-40
—
+85
°C
Operating Junction Temperature Range
TJ
-40
—
+140
°C
Operating Ambient Temperature Range
TA
-40
—
+125
°C
Industrial Temperature Devices
Extended Temperature Devices
Power Dissipation:
Internal chip power dissipation:
PINT = VDD x (IDD –  IOH)
PD
PINT + PI/O
W
PDMAX
(TJ – TA)/JA
W
I/O Pin Power Dissipation:
I/O =  ({VDD – VOH} x IOH) +  (VOL x IOL)
Maximum Allowed Power Dissipation
TABLE 24-3:
THERMAL PACKAGING CHARACTERISTICS
Characteristic
Symbol
Package Thermal Resistance, 100-pin TQFP (14x14x1 mm)
Package Thermal Resistance, 100-pin TQFP (12x12x1 mm)
Package Thermal Resistance, 64-pin TQFP (10x10x1 mm)
Package Thermal Resistance, 64-pin QFN (9x9x0.9 mm)
Note 1:
JA
JA
JA
JA
Typ
Max
Unit
Notes
40
—
°C/W
1
40
—
°C/W
1
40
—
°C/W
1
28
—
°C/W
1
Junction to ambient thermal resistance, Theta-JA (JA) numbers are achieved by package simulations.
DS70592B-page 240
Preliminary
 2009 Microchip Technology Inc.
PIC24HJXXXGPX06A/X08A/X10A
TABLE 24-4:
DC TEMPERATURE AND VOLTAGE SPECIFICATIONS
Standard Operating Conditions: 3.0V to 3.6V
(unless otherwise stated)
Operating temperature -40°C  TA  +85°C for Industrial
-40°C  TA  +125°C for Extended
DC CHARACTERISTICS
Param
Symbol
No.
Characteristic
Min
Typ(1)
Max
Units
3.0
—
3.6
V
Conditions
Operating Voltage
DC10
Supply Voltage
VDD
Voltage(2)
Industrial and Extended
DC12
VDR
RAM Data Retention
1.8
—
—
V
—
DC16
VPOR
VDD Start Voltage(4)
to ensure internal
Power-on Reset signal
—
—
VSS
V
—
DC17
SVDD
VDD Rise Rate
to ensure internal
Power-on Reset signal
0.03
—
—
DC18
VCORE
VDD Core(3)
Internal regulator voltage
2.25
—
2.75
Note 1:
2:
3:
4:
V/ms 0-3.0V in 0.1s
V
Voltage is dependent on
load, temperature and
VDD
Data in “Typ” column is at 3.3V, 25°C unless otherwise stated.
This is the limit to which VDD can be lowered without losing RAM data.
These parameters are characterized but not tested in manufacturing.
VDD voltage must remain at VSS for a minimum of 200 s to ensure POR.
 2009 Microchip Technology Inc.
Preliminary
DS70592B-page 241
PIC24HJXXXGPX06A/X08A/X10A
TABLE 24-5:
DC CHARACTERISTICS: OPERATING CURRENT (IDD)
Standard Operating Conditions: 3.0V to 3.6V
(unless otherwise stated)
Operating temperature -40°C  TA  +85°C for Industrial
-40°C  TA  +125°C for Extended
DC CHARACTERISTICS
Parameter
No.
Typical(1)
Max
Units
Conditions
Operating Current (IDD)(2)
DC20d
27
30
mA
-40°C
DC20a
27
30
mA
+25°C
DC20b
27
30
mA
+85°C
DC20c
27
35
mA
+125°C
DC21d
36
40
mA
-40°C
DC21a
37
40
mA
+25°C
DC21b
38
45
mA
+85°C
DC21c
39
45
mA
+125°C
DC22d
43
50
mA
-40°C
DC22a
46
50
mA
+25°C
DC22b
46
55
mA
+85°C
DC22c
47
55
mA
+125°C
DC23d
65
70
mA
-40°C
DC23a
65
70
mA
+25°C
DC23b
65
70
mA
+85°C
DC23c
65
70
mA
+125°C
DC24d
84
90
mA
-40°C
DC24a
84
90
mA
+25°C
DC24b
84
90
mA
+85°C
DC24c
84
90
mA
+125°C
Note 1:
2:
3.3V
10 MIPS
3.3V
16 MIPS
3.3V
20 MIPS
3.3V
30 MIPS
3.3V
40 MIPS
Data in “Typical” column is at 3.3V, 25°C unless otherwise stated.
The supply current is mainly a function of the operating voltage and frequency. Other factors, such as I/O
pin loading and switching rate, oscillator type, internal code execution pattern and temperature, also have
an impact on the current consumption. The test conditions for all IDD measurements are as follows: OSC1
driven with external square wave from rail to rail. All I/O pins are configured as inputs and pulled to VSS.
MCLR = VDD, WDT and FSCM are disabled. CPU, SRAM, program memory and data memory are
operational. No peripheral modules are operating; however, every peripheral is being clocked (PMD bits
are all zeroed).
DS70592B-page 242
Preliminary
 2009 Microchip Technology Inc.
PIC24HJXXXGPX06A/X08A/X10A
TABLE 24-6:
DC CHARACTERISTICS: IDLE CURRENT (IIDLE)
Standard Operating Conditions: 3.0V to 3.6V
(unless otherwise stated)
Operating temperature -40°C  TA  +85°C for Industrial
-40°C  TA  +125°C for Extended
DC CHARACTERISTICS
Parameter
No.
Typical(1)
Max
Units
Conditions
Idle Current (IIDLE): Core OFF Clock ON Base Current(2)
DC40d
3
25
mA
-40°C
DC40a
3
25
mA
+25°C
DC40b
3
25
mA
+85°C
DC40c
3
25
mA
+125°C
DC41d
4
25
mA
-40°C
DC41a
5
25
mA
+25°C
DC41b
6
25
mA
+85°C
DC41c
6
25
mA
+125°C
DC42d
8
25
mA
-40°C
DC42a
9
25
mA
+25°C
DC42b
10
25
mA
+85°C
DC42c
10
25
mA
+125°C
DC43a
15
25
mA
+25°C
DC43d
15
25
mA
-40°C
DC43b
15
25
mA
+85°C
DC43c
15
25
mA
+125°C
DC44d
16
25
mA
-40°C
DC44a
16
25
mA
+25°C
DC44b
16
25
mA
+85°C
DC44c
16
25
mA
+125°C
Note 1:
2:
3.3V
10 MIPS
3.3V
16 MIPS
3.3V
20 MIPS
3.3V
30 MIPS
3.3V
40 MIPS
Data in “Typical” column is at 3.3V, 25°C unless otherwise stated.
Base IIDLE current is measured with core off, clock on and all modules turned off. Peripheral Module
Disable SFR registers are zeroed. All I/O pins are configured as inputs and pulled to VSS.
 2009 Microchip Technology Inc.
Preliminary
DS70592B-page 243
PIC24HJXXXGPX06A/X08A/X10A
TABLE 24-7:
DC CHARACTERISTICS: POWER-DOWN CURRENT (IPD)
Standard Operating Conditions: 3.0V to 3.6V
(unless otherwise stated)
Operating temperature -40°C  TA  +85°C for Industrial
-40°C  TA  +125°C for Extended
DC CHARACTERISTICS
Parameter
No.
Typical(1)
Max
Units
Conditions
Power-Down Current (IPD)(2)
DC60d
400(4)
50(5)
500(4)
200(5)
A
-40°C
DC60a
400(4)
50(5)
500(4)
200(5)
A
+25°C
DC60b
500(4)
200(5)
800(4)
500(5)
A
+85°C
DC60c
1000(4)
600(5)
1500(4)
1000(5)
A
+125°C
DC61d
8
13
A
-40°C
DC61a
10
15
A
+25°C
DC61b
12
20
A
+85°C
DC61c
13
25
A
+125°C
Note 1:
2:
3:
4:
5:
Base Power-Down Current(3)
3.3V
Watchdog Timer Current: IWDT(3)
Data in the Typical column is at 3.3V, 25°C unless otherwise stated.
Base IPD is measured with all peripherals and clocks shut down. All I/Os are configured as inputs and
pulled to VSS. WDT, etc., are all switched off.
The  current is the additional current consumed when the module is enabled. This current should be
added to the base IPD current.
These characteristics apply to all devices with the exception of the PIC24HJ256GP610A.
These characteristics apply to PIC24HJ256GP610A devices only.
TABLE 24-8:
DC CHARACTERISTICS: DOZE CURRENT (IDOZE)
Standard Operating Conditions: 3.0V to 3.6V
(unless otherwise stated)
Operating temperature -40°C  TA  +85°C for Industrial
-40°C  TA  +125°C for Extended
DC CHARACTERISTICS
Doze
Ratio
Units
35
1:2
mA
30
1:64
mA
11
30
1:128
mA
42
50
1:2
mA
Parameter No.
Typical(1)
Max
DC73a
11
DC73f
11
DC73g
DC70a
DC70f
26
30
1:64
mA
DC70g
25
30
1:128
mA
DC71a
41
50
1:2
mA
DC71f
25
30
1:64
mA
DC71g
24
30
1:128
mA
DC72a
42
50
1:2
mA
DC72f
26
30
1:64
mA
DC72g
25
30
1:128
mA
Note 1:
3.3V
Conditions
-40°C
3.3V
40 MIPS
+25°C
3.3V
40 MIPS
+85°C
3.3V
40 MIPS
+125°C
3.3V
40 MIPS
Data in the Typical column is at 3.3V, 25°C unless otherwise stated.
DS70592B-page 244
Preliminary
 2009 Microchip Technology Inc.
PIC24HJXXXGPX06A/X08A/X10A
TABLE 24-9:
DC CHARACTERISTICS: I/O PIN INPUT SPECIFICATIONS
Standard Operating Conditions: 3.0V to 3.6V
(unless otherwise stated)
Operating temperature -40°C  TA  +85°C for Industrial
-40°C  TA  +125°C for Extended
DC CHARACTERISTICS
Param
Symbol
No.
VIL
Characteristic
Min
Typ(1)
Max
Units
Conditions
Input Low Voltage
DI10
I/O pins
VSS
—
0.2 VDD
V
DI15
MCLR
VSS
—
0.2 VDD
V
DI16
I/O Pins with OSC1 or SOSCI
VSS
—
0.2 VDD
V
DI18
I/O Pins with I2C
VSS
—
0.3 VDD
V
SMbus disabled
VSS
—
0.2 VDD
V
SMbus enabled
0.7 VDD
0.7 VDD
—
—
VDD
5.5
V
V
50
250
400
A
VDD = 3.3V, VPIN = VSS
2
DI19
I/O Pins with I C
VIH
Input High Voltage
I/O Pins Not 5V Tolerant(4)
I/O Pins 5V Tolerant(4)
DI20
ICNPU
CNx Pull-up Current
IIL
Input Leakage Current(2,3)
DI30
DI50
I/O Pins 5V Tolerant(4)
—
—
±2
A
VSS  VPIN  VDD,
Pin at high-impedance
DI51
I/O Pins Not 5V Tolerant(4)
—
—
±1
A
VSS  VPIN  VDD,
Pin at high-impedance,
-40°C  TA  +85°C
DI51a
I/O Pins Not 5V Tolerant(4)
—
—
±2
A
Shared with external reference
pins, -40°C  TA  +85°C
DI51b
I/O Pins Not 5V Tolerant(4)
—
—
±3.5
A
VSS  VPIN  VDD, Pin at
high-impedance,
-40°C  TA  +125°C
DI51c
I/O Pins Not 5V Tolerant(4)
—
—
±8
A
Analog pins shared with
external reference pins,
-40°C  TA  +125°C
DI55
MCLR
—
—
±2
A
VSS VPIN VDD
DI56
OSC1
—
—
±2
A
VSS VPIN VDD,
XT and HS modes
Note 1:
2:
3:
4:
Data in “Typ” column is at 3.3V, 25°C unless otherwise stated.
The leakage current on the MCLR pin is strongly dependent on the applied voltage level. The specified
levels represent normal operating conditions. Higher leakage current may be measured at different input
voltages.
Negative current is defined as current sourced by the pin.
See “Pin Diagrams (Continued)” for a list of 5V tolerant pins.
 2009 Microchip Technology Inc.
Preliminary
DS70592B-page 245
PIC24HJXXXGPX06A/X08A/X10A
TABLE 24-10: DC CHARACTERISTICS: I/O PIN OUTPUT SPECIFICATIONS
Standard Operating Conditions: 3.0V to 3.6V
(unless otherwise stated)
Operating temperature -40°C  TA  +85°C for Industrial
-40°C  TA  +125°C for Extended
DC CHARACTERISTICS
Param
Symbol
No.
VOL
DO10
DO16
VOH
Characteristic
Min
Typ
Max
Units
Conditions
I/O ports
—
—
0.4
V
IOL = 2 mA, VDD = 3.3V
OSC2/CLKO
—
—
0.4
V
IOL = 2 mA, VDD = 3.3V
Output Low Voltage
Output High Voltage
DO20
I/O ports
2.40
—
—
V
IOH = -2.3 mA, VDD = 3.3V
DO26
OSC2/CLKO
2.41
—
—
V
IOH = -1.3 mA, VDD = 3.3V
TABLE 24-11: ELECTRICAL CHARACTERISTICS: BOR
DC CHARACTERISTICS
Param
No.
Symbol
Standard Operating Conditions: 3.0V to 3.6V
(unless otherwise stated)
Operating temperature -40°C  TA  +85°C for Industrial
-40°C  TA  +125°C for Extended
Characteristic
Min(1)
Typ
Max(1)
Units
Conditions
BOR Event on VDD transition
high-to-low
BOR event is tied to VDD core voltage
decrease
2.40
—
2.55
V
—
BO10
VBOR
Note 1:
Parameters are for design guidance only and are not tested in manufacturing.
DS70592B-page 246
Preliminary
 2009 Microchip Technology Inc.
PIC24HJXXXGPX06A/X08A/X10A
TABLE 24-12: DC CHARACTERISTICS: PROGRAM MEMORY
Standard Operating Conditions: 3.0V to 3.6V
(unless otherwise stated)
Operating temperature -40°C  TA  +85°C for Industrial
-40°C  TA  +125°C for Extended
DC CHARACTERISTICS
Param
Symbol
No.
Characteristic
Min
Typ(1)
Max
Units
Conditions
Program Flash Memory
D130
EP
Cell Endurance
10,000
—
—
E/W
D131
VPR
VDD for Read
VMIN
—
3.6
V
VMIN = Minimum operating
voltage
D132b
VPEW
VDD for Self-Timed Write
VMIN
—
3.6
V
VMIN = Minimum operating
voltage
D134
TRETD
Characteristic Retention
20
—
—
Year Provided no other specifications are
violated
D135
IDDP
Supply Current during
Programming
—
10
—
mA
D136a
TRW
Row Write Time
1.32
—
1.74
ms
TRW = 11064 FRC cycles,
TA = +85°C, See Note 2
D136b
TRW
Row Write Time
1.28
—
1.79
ms
TRW = 11064 FRC cycles,
TA = +125°C, See Note 2
D137a
TPE
Page Erase Time
20.1
—
26.5
ms
TPE = 168517 FRC cycles,
TA = +85°C, See Note 2
D137b
TPE
Page Erase Time
19.5
—
27.3
ms
TPE = 168517 FRC cycles,
TA = +125°C, See Note 2
D138a
TWW
Word Write Cycle Time
42.3
—
55.9
µs
TWW = 355 FRC cycles,
TA = +85°C, See Note 2
D138b
TWW
Word Write Cycle Time
41.1
—
57.6
µs
TWW = 355 FRC cycles,
TA = +125°C, See Note 2
Note 1:
2:
Data in “Typ” column is at 3.3V, 25°C unless otherwise stated.
Other conditions: FRC = 7.37 MHz, TUN<5:0> = b'011111 (for Min), TUN<5:0> = b'100000 (for Max).
This parameter depends on the FRC accuracy (see Table 24-19) and the value of the FRC Oscillator Tuning register (see Register 9-4). For complete details on calculating the Minimum and Maximum time see
Section 5.3 “Programming Operations”.
TABLE 24-13: INTERNAL VOLTAGE REGULATOR SPECIFICATIONS
Standard Operating Conditions: 3.0V to 3.6V
(unless otherwise stated)
Operating temperature -40°C  TA  +85°C for Industrial
-40°C  TA  +125°C for Extended
Param
No.
Symbol
CEFC
Characteristics
External Filter Capacitor
Value
 2009 Microchip Technology Inc.
Min
Typ
Max
Units
4.7
10
—
F
Preliminary
Comments
Capacitor must be low
series resistance
(< 5 Ohms)
DS70592B-page 247
PIC24HJXXXGPX06A/X08A/X10A
24.2
AC Characteristics and Timing
Parameters
This section defines PIC24HJXXXGPX06A/X08A/
X10A AC characteristics and timing parameters.
TABLE 24-14: TEMPERATURE AND VOLTAGE SPECIFICATIONS – AC
Standard Operating Conditions: 3.0V to 3.6V
(unless otherwise stated)
Operating temperature -40°C  TA  +85°C for Industrial
-40°C  TA  +125°C for Extended
Operating voltage VDD range as described in Section 24.0 “Electrical
Characteristics”.
AC CHARACTERISTICS
FIGURE 24-1:
LOAD CONDITIONS FOR DEVICE TIMING SPECIFICATIONS
Load Condition 1 – for all pins except OSC2
Load Condition 2 – for OSC2
VDD/2
CL
Pin
RL
VSS
CL
Pin
RL = 464
CL = 50 pF for all pins except OSC2
15 pF for OSC2 output
VSS
TABLE 24-15: CAPACITIVE LOADING REQUIREMENTS ON OUTPUT PINS
Param
Symbol
No.
Characteristic
Min
Typ
Max
Units
Conditions
15
pF
In XT and HS modes when
external clock is used to drive
OSC1
DO50
COSCO
OSC2/SOSCO pin
—
—
DO56
CIO
All I/O pins and OSC2
—
—
50
pF
EC mode
DO58
CB
SCLx, SDAx
—
—
400
pF
In I2C™ mode
DS70592B-page 248
Preliminary
 2009 Microchip Technology Inc.
PIC24HJXXXGPX06A/X08A/X10A
FIGURE 24-2:
EXTERNAL CLOCK TIMING
Q1
Q2
Q3
Q4
Q1
Q2
Q3
Q4
OSC1
OS20
OS30
OS25
OS30
OS31
OS31
CLKO
OS41
OS40
TABLE 24-16: EXTERNAL CLOCK TIMING REQUIREMENTS
Standard Operating Conditions: 3.0V to 3.6V
(unless otherwise stated)
Operating temperature -40°C  TA  +85°C for Industrial
-40°C  TA  +125°C for Extended
AC CHARACTERISTICS
Param
Symbol
No.
OS10
FIN
OS20
TOSC
Min
Typ(1)
Max
Units
External CLKI Frequency
(External clocks allowed only
in EC and ECPLL modes)
DC
—
40
MHz
EC
Oscillator Crystal Frequency
3.5
10
—
—
—
10
40
33
MHz
MHz
kHz
XT
HS
SOSC
TOSC = 1/FOSC
12.5
—
DC
ns
—
Characteristic
Time(2)
Conditions
OS25
TCY
Instruction Cycle
25
—
DC
ns
—
OS30
TosL,
TosH
External Clock in (OSC1)
High or Low Time
0.375 x TOSC
—
0.625 x TOSC
ns
EC
OS31
TosR,
TosF
External Clock in (OSC1)
Rise or Fall Time
—
—
20
ns
EC
OS40
TckR
CLKO Rise Time(3)
—
5.2
—
ns
—
OS41
TckF
CLKO Fall Time(3)
—
5.2
—
ns
—
OS42
GM
External Oscillator
Transconductance(4)
14
16
18
mA/V
Note 1:
2:
3:
4:
VDD = 3.3V
TA = +25ºC
Data in “Typ” column is at 3.3V, 25°C unless otherwise stated.
Instruction cycle period (TCY) equals two times the input oscillator time-base period. All specified values
are based on characterization data for that particular oscillator type under standard operating conditions
with the device executing code. Exceeding these specified limits may result in an unstable oscillator
operation and/or higher than expected current consumption. All devices are tested to operate at “min.”
values with an external clock applied to the OSC1/CLKI pin. When an external clock input is used, the
“max.” cycle time limit is “DC” (no clock) for all devices.
Measurements are taken in EC mode. The CLKO signal is measured on the OSC2 pin.
Data for this parameter is Preliminary. This parameter is characterized, but not tested in manufacturing.
 2009 Microchip Technology Inc.
Preliminary
DS70592B-page 249
PIC24HJXXXGPX06A/X08A/X10A
TABLE 24-17: PLL CLOCK TIMING SPECIFICATIONS (VDD = 3.0V TO 3.6V)
Standard Operating Conditions: 3.0V to 3.6V (unless otherwise stated)
Operating temperature -40°C  TA  +85°C for Industrial
-40°C  TA  +125°C for Extended
AC CHARACTERISTICS
Param
No.
Symbol
Characteristic
Min
Typ(1)
Max
Units
OS50
FPLLI
PLL Voltage Controlled
Oscillator (VCO) Input
Frequency Range
0.8
—
8
MHz
OS51
FSYS
On-Chip VCO System
Frequency
100
—
200
MHz
OS52
TLOCK
PLL Start-up Time (Lock Time)
0.9
1.5
3.1
mS
OS53
DCLK
CLKO Stability (Jitter)
-3
0.5
3
%
Note 1:
Conditions
ECPLL, HSPLL, XTPLL
modes
Measured over 100 ms
period
Data in “Typ” column is at 3.3V, 25°C unless otherwise stated. Parameters are for design guidance only
and are not tested.
TABLE 24-18: AC CHARACTERISTICS: INTERNAL RC ACCURACY
AC CHARACTERISTICS
Param
No.
Characteristic
Standard Operating Conditions: 3.0V to 3.6V (unless otherwise stated)
Operating temperature
-40°C  TA  +85°C for Industrial
-40°C  TA  +125°C for Extended
Min
Typ
Max
Units
Conditions
Internal FRC Accuracy @ 7.3728 MHz(1,2)
F20a
FRC
-2
—
+2
%
-40°C  TA +85°C
VDD = 3.0-3.6V
F20b
FRC
-5
—
+5
%
-40°C  TA +125°C
VDD = 3.0-3.6V
Note 1:
2:
Frequency calibrated at 25°C and 3.3V. TUN bits can be used to compensate for temperature drift.
FRC is set to initial frequency of 7.37 MHz (±2%) at 25°C.
TABLE 24-19: INTERNAL RC ACCURACY
AC CHARACTERISTICS
Param
No.
Characteristic
Standard Operating Conditions: 3.0V to 3.6V (unless otherwise stated)
Operating temperature -40°C  TA  +85°C for Industrial
-40°C  TA  +125°C for Extended
Min
Typ
Max
Units
Conditions
LPRC
-30
—
+30
%
-40°C  TA +85°C
LPRC
-70(2)
%
-40°C  TA +125°C
LPRC @ 32.768 kHz(1)
F21a
F21b
-35(3)
Note 1:
2:
3:
(2)
—
—(3)
(2)
+70
+35(3)
Change of LPRC frequency as VDD changes.
These characteristics apply to all devices with the exception of the PIC24HJ256GPX06A/X08A/X10A.
These characteristics apply to PIC24HJ256GPX06A/X08A/X10A devices only.
DS70592B-page 250
Preliminary
 2009 Microchip Technology Inc.
PIC24HJXXXGPX06A/X08A/X10A
FIGURE 24-3:
CLKO AND I/O TIMING CHARACTERISTICS
I/O Pin
(Input)
DI35
DI40
I/O Pin
(Output)
New Value
Old Value
DO31
DO32
Note: Refer to Figure 24-1 for load conditions.
TABLE 24-20: I/O TIMING REQUIREMENTS
Standard Operating Conditions: 3.0V to 3.6V
(unless otherwise stated)
Operating temperature -40°C  TA  +85°C for Industrial
-40°C  TA  +125°C for Extended
AC CHARACTERISTICS
Param
No.
Symbol
Characteristic
Min
Typ(1)
Max
Units
Conditions
DO31
TIOR
Port Output Rise Time
—
10
25
ns
—
DO32
TIOF
Port Output Fall Time
—
10
25
ns
—
DI35
TINP
INTx Pin High or Low Time (output)
20
—
—
ns
—
DI40
TRBP
CNx High or Low Time (input)
2
—
—
TCY
—
Note 1:
Data in “Typ” column is at 3.3V, 25°C unless otherwise stated.
 2009 Microchip Technology Inc.
Preliminary
DS70592B-page 251
PIC24HJXXXGPX06A/X08A/X10A
FIGURE 24-4:
VDD
RESET, WATCHDOG TIMER, OSCILLATOR START-UP TIMER AND POWER-UP
TIMER TIMING CHARACTERISTICS
SY12
MCLR
SY10
Internal
POR
SY11
PWRT
Time-out
OSC
Time-out
SY30
Internal
Reset
Watchdog
Timer
Reset
SY20
SY13
SY13
I/O Pins
SY35
FSCM
Delay
DS70592B-page 252
Note: Refer to Figure 24-1 for load conditions.
Preliminary
 2009 Microchip Technology Inc.
PIC24HJXXXGPX06A/X08A/X10A
TABLE 24-21: RESET, WATCHDOG TIMER, OSCILLATOR START-UP TIMER, POWER-UP TIMER
TIMING REQUIREMENTS
AC CHARACTERISTICS
Standard Operating Conditions: 3.0V to 3.6V
(unless otherwise stated)
Operating temperature -40°C  TA  +85°C for Industrial
-40°C  TA  +125°C for Extended
Param
Symbol
No.
Min
Typ(2)
Max
Units
Characteristic(1)
Conditions
SY10
TMCL
MCLR Pulse Width (low)
2
—
—
s
-40°C to +85°C
SY11
TPWRT
Power-up Timer Period
—
2
4
8
16
32
64
128
—
ms
-40°C to +85°C
User programmable
SY12
TPOR
Power-on Reset Delay
3
10
30
s
-40°C to +85°C
SY13
TIOZ
I/O High-Impedance from
MCLR Low or Watchdog
Timer Reset
0.68
0.72
1.2
s
—
SY20
TWDT1
Watchdog Timer Time-out
Period
—
—
—
—
See Section 21.4 “Watchdog
Timer (WDT)” and LPRC
specification F21 (Table 24-19)
SY30
TOST
Oscillator Start-up Timer
Period
—
1024 TOSC
—
—
TOSC = OSC1 period
SY35
TFSCM
Fail-Safe Clock Monitor
Delay
—
500
900
s
-40°C to +85°C
Note 1:
2:
These parameters are characterized but not tested in manufacturing.
Data in “Typ” column is at 3.3V, 25°C unless otherwise stated.
 2009 Microchip Technology Inc.
Preliminary
DS70592B-page 253
PIC24HJXXXGPX06A/X08A/X10A
FIGURE 24-5:
TIMER1, 2, 3, 4, 5, 6, 7, 8 AND 9 EXTERNAL CLOCK TIMING CHARACTERISTICS
TxCK
Tx11
Tx10
Tx15
OS60
Tx20
TMRx
Note: Refer to Figure 24-1 for load conditions.
TABLE 24-22: TIMER1 EXTERNAL CLOCK TIMING REQUIREMENTS(1)
Standard Operating Conditions: 3.0V to 3.6V
(unless otherwise stated)
Operating temperature -40°C  TA  +85°C for Industrial
-40°C  TA  +125°C for Extended
AC CHARACTERISTICS
Param
No.
TA10
TA11
TA15
Symbol
TTXH
TTXL
TTXP
Characteristic
TxCK High Time
TxCK Low Time
Min
Typ
Max
Units
Conditions
Synchronous,
no prescaler
0.5 TCY + 20
—
—
ns
Must also meet
parameter TA15
Synchronous,
with prescaler
10
—
—
ns
Asynchronous
10
—
—
ns
Synchronous,
no prescaler
0.5 TCY + 20
—
—
ns
Synchronous,
with prescaler
10
—
—
ns
Asynchronous
10
—
—
ns
TCY + 40
—
—
ns
Synchronous,
with prescaler
Greater of:
20 ns or
(TCY + 40)/N
—
—
—
Asynchronous
20
—
—
ns
—
DC
—
50
kHz
—
1.5 TCY
—
—
TxCK Input Period Synchronous,
no prescaler
OS60
Ft1
TA20
TCKEXTMRL Delay from External TxCK Clock
Edge to Timer Increment
Note 1:
SOSCI/T1CK Oscillator Input
frequency Range (oscillator enabled
by setting bit TCS (T1CON<1>))
0.5 TCY
Must also meet
parameter TA15
—
N = prescale
value
(1, 8, 64, 256)
Timer1 is a Type A.
DS70592B-page 254
Preliminary
 2009 Microchip Technology Inc.
PIC24HJXXXGPX06A/X08A/X10A
TABLE 24-23: TIMER2, 4, 6 AND 8 EXTERNAL CLOCK TIMING REQUIREMENTS
Standard Operating Conditions: 3.0V to 3.6V
(unless otherwise stated)
Operating temperature -40°C  TA  +85°C for Industrial
-40°C  TA  +125°C for Extended
AC CHARACTERISTICS
Param
No.
TB10
TB11
TB15
TB20
Symbol
TtxH
TtxL
TtxP
TCKEXTMRL
Characteristic
TxCK High Time
TxCK Low Time
TxCK Input
Period
Min
Typ
Max
Units
Conditions
Synchronous,
no prescaler
0.5 TCY + 20
—
—
ns
Must also meet
parameter TB15
Synchronous,
with prescaler
10
—
—
ns
Synchronous,
no prescaler
0.5 TCY + 20
—
—
ns
Synchronous,
with prescaler
10
—
—
ns
Synchronous,
no prescaler
TCY + 40
—
—
ns
Synchronous,
with prescaler
Greater of:
20 ns or
(TCY + 40)/N
—
1.5 TCY
—
Delay from External TxCK Clock
Edge to Timer Increment
0.5 TCY
Must also meet
parameter TB15
N = prescale
value
(1, 8, 64, 256)
—
TABLE 24-24: TIMER3, 5, 7 AND 9 EXTERNAL CLOCK TIMING REQUIREMENTS
Standard Operating Conditions: 3.0V to 3.6V
(unless otherwise stated)
Operating temperature -40°C  TA  +85°C for Industrial
-40°C  TA  +125°C for Extended
AC CHARACTERISTICS
Param
No.
Symbol
Characteristic
Min
Typ
Max
Units
Conditions
TC10
TtxH
TxCK High Time
Synchronous
0.5 TCY + 20
—
—
ns
Must also meet
parameter TC15
TC11
TtxL
TxCK Low Time
Synchronous
0.5 TCY + 20
—
—
ns
Must also meet
parameter TC15
TC15
TtxP
TxCK Input Period Synchronous,
no prescaler
TCY + 40
—
—
ns
N = prescale
value
(1, 8, 64, 256)
—
1.5
TCY
—
Synchronous,
with prescaler
TC20
TCKEXTMRL Delay from External TxCK Clock
Edge to Timer Increment
 2009 Microchip Technology Inc.
Greater of:
20 ns or
(TCY + 40)/N
0.5 TCY
Preliminary
—
DS70592B-page 255
PIC24HJXXXGPX06A/X08A/X10A
FIGURE 24-6:
INPUT CAPTURE (CAPx) TIMING CHARACTERISTICS
ICx
IC10
IC11
IC15
Note: Refer to Figure 24-1 for load conditions.
TABLE 24-25: INPUT CAPTURE TIMING REQUIREMENTS
Standard Operating Conditions: 3.0V to 3.6V
(unless otherwise stated)
Operating temperature -40°C  TA  +85°C for Industrial
-40°C  TA  +125°C for Extended
AC CHARACTERISTICS
Param
No.
Symbol
IC10
TccL
ICx Input Low Time
IC11
TccH
ICx Input High Time
IC15
TccP
ICx Input Period
Characteristic(1)
No Prescaler
Min
Max
Units
Conditions
0.5 TCY + 20
—
ns
—
With Prescaler
No Prescaler
10
—
ns
0.5 TCY + 20
—
ns
With Prescaler
Note 1:
10
—
ns
(TCY + 40)/N
—
ns
—
N = prescale
value (1, 4, 16)
These parameters are characterized but not tested in manufacturing.
FIGURE 24-7:
OUTPUT COMPARE MODULE (OCx) TIMING CHARACTERISTICS
OCx
(Output Compare
or PWM Mode)
OC10
OC11
Note: Refer to Figure 24-1 for load conditions.
TABLE 24-26: OUTPUT COMPARE MODULE TIMING REQUIREMENTS
AC CHARACTERISTICS
Param
Symbol
No.
Characteristic(1)
Standard Operating Conditions: 3.0V to 3.6V
(unless otherwise stated)
Operating temperature -40°C  TA  +85°C for Industrial
-40°C  TA  +125°C for Extended
Min
Typ
Max
Units
Conditions
OC10
TccF
OCx Output Fall Time
—
—
—
ns
See parameter D032
OC11
TccR
OCx Output Rise Time
—
—
—
ns
See parameter D031
Note 1:
These parameters are characterized but not tested in manufacturing.
DS70592B-page 256
Preliminary
 2009 Microchip Technology Inc.
PIC24HJXXXGPX06A/X08A/X10A
FIGURE 24-8:
OC/PWM MODULE TIMING CHARACTERISTICS
OC20
OCFA
OC15
OCx
TABLE 24-27: SIMPLE OC/PWM MODE TIMING REQUIREMENTS
Standard Operating Conditions: 3.0V to 3.6V
(unless otherwise stated)
Operating temperature -40°C  TA  +85°C for Industrial
-40°C  TA  +125°C for Extended
AC CHARACTERISTICS
Param
No.
Symbol
Characteristic(1)
Min
Typ
Max
Units
Conditions
OC15
TFD
Fault Input to PWM I/O
Change
—
—
50
ns
—
OC20
TFLT
Fault Input Pulse-Width
50
—
—
ns
—
Note 1:
These parameters are characterized but not tested in manufacturing.
 2009 Microchip Technology Inc.
Preliminary
DS70592B-page 257
PIC24HJXXXGPX06A/X08A/X10A
FIGURE 24-9:
SPIx MODULE MASTER MODE (CKE = 0) TIMING CHARACTERISTICS
SCKx
(CKP = 0)
SP11
SP10
SP21
SP20
SP20
SP21
SCKx
(CKP = 1)
SP35
Bit 14 - - - - - -1
MSb
SDOx
SP31
SDIx
LSb
SP30
MSb In
LSb In
Bit 14 - - - -1
SP40 SP41
Note: Refer to Figure 24-1 for load conditions.
TABLE 24-28: SPIx MASTER MODE (CKE = 0) TIMING REQUIREMENTS
Standard Operating Conditions: 3.0V to 3.6V
(unless otherwise stated)
Operating temperature -40°C  TA  +85°C for Industrial
-40°C  TA  +125°C for Extended
AC CHARACTERISTICS
Param
No.
Symbol
Characteristic(1)
Min
Typ(2)
Max
Units
Conditions
SP10
TscL
SCKx Output Low Time
TCY/2
—
—
ns
See Note 3
SP11
TscH
SCKx Output High Time
TCY/2
—
—
ns
See Note 3
SP20
TscF
SCKx Output Fall Time
—
—
—
ns
See parameter D032
and Note 4
SP21
TscR
SCKx Output Rise Time
—
—
—
ns
See parameter D031
and Note 4
SP30
TdoF
SDOx Data Output Fall Time
—
—
—
ns
See parameter D032
and Note 4
SP31
TdoR
SDOx Data Output Rise Time
—
—
—
ns
See parameter D031
and Note 4
SP35
TscH2doV,
TscL2doV
SDOx Data Output Valid after
SCKx Edge
—
6
20
ns
—
SP40
TdiV2scH,
TdiV2scL
Setup Time of SDIx Data Input
to SCKx Edge
23
—
—
ns
—
SP41
TscH2diL,
TscL2diL
Hold Time of SDIx Data Input
to SCKx Edge
30
—
—
ns
—
Note 1:
2:
3:
4:
These parameters are characterized but not tested in manufacturing.
Data in “Typ” column is at 3.3V, 25°C unless otherwise stated.
The minimum clock period for SCKx is 100 ns. Therefore, the clock generated in Master mode must not
violate this specification.
Assumes 50 pF load on all SPIx pins.
DS70592B-page 258
Preliminary
 2009 Microchip Technology Inc.
PIC24HJXXXGPX06A/X08A/X10A
FIGURE 24-10:
SPIx MODULE MASTER MODE (CKE = 1) TIMING CHARACTERISTICS
SP36
SCKX
(CKP = 0)
SP11
SP10
SP21
SP20
SP20
SP21
SCKX
(CKP = 1)
SP35
SP40
SDIX
LSb
Bit 14 - - - - - -1
MSb
SDOX
SP30,SP31
MSb In
Bit 14 - - - -1
LSb In
SP41
Note: Refer to Figure 24-1 for load conditions.
TABLE 24-29: SPIx MODULE MASTER MODE (CKE = 1) TIMING REQUIREMENTS
Standard Operating Conditions: 3.0V to 3.6V
(unless otherwise stated)
Operating temperature -40°C  TA  +85°C for Industrial
-40°C  TA  +125°C for Extended
AC CHARACTERISTICS
Param
No.
Symbol
Characteristic(1)
Min
Typ(2)
Max
Units
Conditions
SP10
TscL
SCKx Output Low Time(3)
TCY/2
—
—
ns
—
SP11
TscH
SCKx Output High Time(3)
TCY/2
—
—
ns
—
Time(4)
SP20
TscF
SCKx Output Fall
—
—
—
ns
See parameter D032
SP21
TscR
SCKx Output Rise Time(4)
—
—
—
ns
See parameter D031
SP30
TdoF
SDOx Data Output Fall
Time(4)
—
—
—
ns
See parameter D032
SP31
TdoR
SDOx Data Output Rise
Time(4)
—
—
—
ns
See parameter D031
SP35
TscH2doV, SDOx Data Output Valid after
TscL2doV SCKx Edge
—
6
20
ns
—
SP36
TdoV2sc,
TdoV2scL
SDOx Data Output Setup to
First SCKx Edge
30
—
—
ns
—
SP40
TdiV2scH,
TdiV2scL
Setup Time of SDIx Data
Input to SCKx Edge
23
—
—
ns
—
SP41
TscH2diL,
TscL2diL
Hold Time of SDIx Data Input
to SCKx Edge
30
—
—
ns
—
Note 1:
2:
3:
4:
These parameters are characterized but not tested in manufacturing.
Data in “Typ” column is at 3.3V, 25°C unless otherwise stated.
The minimum clock period for SCKx is 100 ns. The clock generated in Master mode must not violate this
specification.
Assumes 50 pF load on all SPIx pins.
 2009 Microchip Technology Inc.
Preliminary
DS70592B-page 259
PIC24HJXXXGPX06A/X08A/X10A
FIGURE 24-11:
SPIx MODULE SLAVE MODE (CKE = 0) TIMING CHARACTERISTICS
SSX
SP52
SP50
SCKX
(CKP = 0)
SP71
SP70
SP73
SP72
SP72
SP73
SCKX
(CKP = 1)
SP35
MSb
SDOX
LSb
Bit 14 - - - - - -1
SP51
SP30,SP31
SDIX
Bit 14 - - - -1
MSb In
LSb In
SP41
SP40
Note: Refer to Figure 24-1 for load conditions.
TABLE 24-30: SPIx MODULE SLAVE MODE (CKE = 0) TIMING REQUIREMENTS
Standard Operating Conditions: 3.0V to 3.6V
(unless otherwise stated)
Operating temperature -40°C  TA  +85°C for Industrial
-40°C  TA  +125°C for Extended
AC CHARACTERISTICS
Param
No.
Symbol
Characteristic(1)
Min
Typ(2)
Max
Units
Conditions
SP70
TscL
SCKx Input Low Time
30
—
—
ns
—
SP71
TscH
SCKx Input High Time
30
—
—
ns
—
SP72
TscF
SCKx Input Fall Time(3)
—
10
25
ns
—
SP73
TscR
SCKx Input Rise Time(3)
—
10
25
ns
—
(3)
SP30
TdoF
SDOx Data Output Fall Time
—
—
—
ns
See parameter D032
SP31
TdoR
SDOx Data Output Rise Time(3)
—
—
—
ns
See parameter D031
SP35
TscH2doV, SDOx Data Output Valid after
TscL2doV SCKx Edge
—
—
30
ns
—
SP40
TdiV2scH,
TdiV2scL
Setup Time of SDIx Data Input
to SCKx Edge
20
—
—
ns
—
SP41
TscH2diL,
TscL2diL
Hold Time of SDIx Data Input
to SCKx Edge
20
—
—
ns
—
SP50
TssL2scH,
TssL2scL
SSx  to SCKx  or SCKx Input
120
—
—
ns
—
SP51
TssH2doZ
SSx  to SDOx Output
High-Impedance(3)
10
—
50
ns
—
SP52
TscH2ssH SSx after SCKx Edge
TscL2ssH
1.5 TCY + 40
—
—
ns
—
Note 1:
2:
3:
These parameters are characterized but not tested in manufacturing.
Data in “Typ” column is at 3.3V, 25°C unless otherwise stated.
Assumes 50 pF load on all SPIx pins.
DS70592B-page 260
Preliminary
 2009 Microchip Technology Inc.
PIC24HJXXXGPX06A/X08A/X10A
FIGURE 24-12:
SPIx MODULE SLAVE MODE (CKE = 1) TIMING CHARACTERISTICS
SP60
SSx
SP52
SP50
SCKx
(CKP = 0)
SP71
SP70
SP73
SP72
SP72
SP73
SCKx
(CKP = 1)
SP35
MSb
SDOx
Bit 14 - - - - - -1
LSb
SP30,SP31
SDIx
SDI
MSb In
SP51
Bit 14 - - - -1
LSb In
SP41
SP40
Note: Refer to Figure 24-1 for load conditions.
 2009 Microchip Technology Inc.
Preliminary
DS70592B-page 261
PIC24HJXXXGPX06A/X08A/X10A
TABLE 24-31: SPIx MODULE SLAVE MODE (CKE = 1) TIMING REQUIREMENTS
Standard Operating Conditions: 3.0V to 3.6V
(unless otherwise stated)
Operating temperature -40°C  TA  +85°C for Industrial
-40°C  TA  +125°C for Extended
AC CHARACTERISTICS
Param
No.
Symbol
Characteristic(1)
Min
Typ(2)
Max
Units
Conditions
SP70
TscL
SCKx Input Low Time
30
—
—
ns
—
SP71
TscH
SCKx Input High Time
30
—
—
ns
—
—
10
25
ns
—
—
10
25
ns
—
—
—
—
ns
See parameter D032
—
—
—
ns
See parameter D031
Time(3)
SP72
TscF
SCKx Input Fall
SP73
TscR
SCKx Input Rise Time(3)
Time(3)
SP30
TdoF
SDOx Data Output Fall
SP31
TdoR
SDOx Data Output Rise Time(3)
SP35
TscH2doV, SDOx Data Output Valid after
TscL2doV SCKx Edge
—
—
30
ns
—
SP40
TdiV2scH, Setup Time of SDIx Data Input
TdiV2scL to SCKx Edge
20
—
—
ns
—
SP41
TscH2diL, Hold Time of SDIx Data Input
TscL2diL to SCKx Edge
20
—
—
ns
—
SP50
TssL2scH, SSx  to SCKx  or SCKx 
TssL2scL Input
120
—
—
ns
—
SP51
TssH2doZ SSx  to SDOX Output
High-Impedance(4)
10
—
50
ns
—
SP52
TscH2ssH SSx  after SCKx Edge
TscL2ssH
1.5 TCY + 40
—
—
ns
—
SP60
TssL2doV SDOx Data Output Valid after
SSx Edge
—
—
50
ns
—
Note 1:
2:
3:
4:
These parameters are characterized but not tested in manufacturing.
Data in “Typ” column is at 3.3V, 25°C unless otherwise stated.
The minimum clock period for SCKx is 100 ns. The clock generated in Master mode must not violate this
specification.
Assumes 50 pF load on all SPIx pins.
DS70592B-page 262
Preliminary
 2009 Microchip Technology Inc.
PIC24HJXXXGPX06A/X08A/X10A
FIGURE 24-13:
I2Cx BUS START/STOP BITS TIMING CHARACTERISTICS (MASTER MODE)
SCLx
IM31
IM34
IM30
IM33
SDAx
Stop
Condition
Start
Condition
Note: Refer to Figure 24-1 for load conditions.
FIGURE 24-14:
I2Cx BUS DATA TIMING CHARACTERISTICS (MASTER MODE)
IM20
IM21
IM11
IM10
SCLx
IM11
IM26
IM10
IM25
IM33
SDAx
In
IM40
IM40
IM45
SDAx
Out
Note: Refer to Figure 24-1 for load conditions.
 2009 Microchip Technology Inc.
Preliminary
DS70592B-page 263
PIC24HJXXXGPX06A/X08A/X10A
TABLE 24-32: I2Cx BUS DATA TIMING REQUIREMENTS (MASTER MODE)
Standard Operating Conditions: 3.0V to 3.6V
(unless otherwise stated)
Operating temperature -40°C  TA  +85°C for Industrial
-40°C  TA  +125°C for Extended
AC CHARACTERISTICS
Param
Symbol
No.
IM10
IM11
IM20
IM21
IM25
IM26
IM30
IM31
IM33
IM34
IM40
IM45
IM50
IM51
Note
Characteristic
Min(1)
Max
Units
Conditions
—
s
—
TLO:SCL Clock Low Time 100 kHz mode TCY/2 (BRG + 1)
400 kHz mode TCY/2 (BRG + 1)
—
s
—
1 MHz mode(2) TCY/2 (BRG + 1)
—
s
—
—
s
—
THI:SCL Clock High Time 100 kHz mode TCY/2 (BRG + 1)
400 kHz mode TCY/2 (BRG + 1)
—
s
—
1 MHz mode(2) TCY/2 (BRG + 1)
—
s
—
SDAx and SCLx 100 kHz mode
—
300
ns
CB is specified to be
TF:SCL
Fall Time
from 10 to 400 pF
400 kHz mode
20 + 0.1 CB
300
ns
(2)
1 MHz mode
—
100
ns
TR:SCL SDAx and SCLx 100 kHz mode
—
1000
ns
CB is specified to be
Rise Time
from 10 to 400 pF
400 kHz mode
20 + 0.1 CB
300
ns
(2)
1 MHz mode
—
300
ns
TSU:DAT Data Input
100 kHz mode
250
—
ns
—
Setup Time
400 kHz mode
100
—
ns
1 MHz mode(2)
40
—
ns
THD:DAT Data Input
100 kHz mode
0
—
s
—
Hold Time
400 kHz mode
0
0.9
s
1 MHz mode(2)
0.2
—
s
TSU:STA Start Condition 100 kHz mode TCY/2 (BRG + 1)
—
s
Only relevant for
Setup Time
Repeated Start
—
s
400 kHz mode TCY/2 (BRG + 1)
condition
(2)
1 MHz mode
TCY/2 (BRG + 1)
—
s
THD:STA Start Condition 100 kHz mode TCY/2 (BRG + 1)
—
s
After this period the
Hold Time
first clock pulse is
—
s
400 kHz mode TCY/2 (BRG + 1)
generated
(2)
1 MHz mode
TCY/2 (BRG + 1)
—
s
TSU:STO Stop Condition 100 kHz mode TCY/2 (BRG + 1)
—
s
—
Setup Time
400 kHz mode TCY/2 (BRG + 1)
—
s
1 MHz mode(2) TCY/2 (BRG + 1)
—
s
THD:STO Stop Condition 100 kHz mode TCY/2 (BRG + 1)
—
ns
—
Hold Time
400 kHz mode TCY/2 (BRG + 1)
—
ns
1 MHz mode(2) TCY/2 (BRG + 1)
—
ns
TAA:SCL Output Valid
100 kHz mode
—
3500
ns
—
From Clock
400 kHz mode
—
1000
ns
—
1 MHz mode(2)
—
400
ns
—
TBF:SDA Bus Free Time 100 kHz mode
4.7
—
s
Time the bus must be
free before a new
400 kHz mode
1.3
—
s
transmission can start
(2)
0.5
—
s
1 MHz mode
CB
Bus Capacitive Loading
—
400
pF
—
TPGD
Pulse Gobbler Delay
65
390
ns
See Note 3
1: BRG is the value of the I2C Baud Rate Generator. Refer to Section 19. “Inter-Integrated Circuit™
(I2C™)” (DS70235) in the “PIC24H Family Reference Manual”. Please see the Microchip website
(www.microchip.com) for the latest PIC24H Family Reference Manual chapters.
2: Maximum pin capacitance = 10 pF for all I2Cx pins (for 1 MHz mode only).
3: Typical value for this parameter is 130 ns.
DS70592B-page 264
Preliminary
 2009 Microchip Technology Inc.
PIC24HJXXXGPX06A/X08A/X10A
FIGURE 24-15:
I2Cx BUS START/STOP BITS TIMING CHARACTERISTICS (SLAVE MODE)
SCLx
IS34
IS31
IS30
IS33
SDAx
Stop
Condition
Start
Condition
FIGURE 24-16:
I2Cx BUS DATA TIMING CHARACTERISTICS (SLAVE MODE)
IS20
IS21
IS11
IS10
SCLx
IS30
IS26
IS31
IS25
IS33
SDAx
In
IS40
IS40
IS45
SDAx
Out
 2009 Microchip Technology Inc.
Preliminary
DS70592B-page 265
PIC24HJXXXGPX06A/X08A/X10A
TABLE 24-33: I2Cx BUS DATA TIMING REQUIREMENTS (SLAVE MODE)
Standard Operating Conditions: 3.0V to 3.6V
(unless otherwise stated)
Operating temperature -40°C  TA  +85°C for Industrial
-40°C  TA  +125°C for Extended
AC CHARACTERISTICS
Param
Symbol
.
IS10
IS11
IS20
IS21
IS25
IS26
IS30
IS31
IS33
IS34
IS40
IS45
IS50
Note 1:
Characteristic
TLO:SCL Clock Low Time
THI:SCL
TF:SCL
TR:SCL
Clock High Time
SDAx and SCLx
Fall Time
SDAx and SCLx
Rise Time
TSU:DAT Data Input
Setup Time
THD:DAT Data Input
Hold Time
TSU:STA
Start Condition
Setup Time
THD:STA Start Condition
Hold Time
TSU:STO Stop Condition
Setup Time
THD:STO Stop Condition
Hold Time
TAA:SCL
Output Valid
From Clock
TBF:SDA Bus Free Time
CB
Min
Max
Units
100 kHz mode
4.7
—
s
Device must operate at a
minimum of 1.5 MHz
400 kHz mode
1.3
—
s
Device must operate at a
minimum of 10 MHz
1 MHz mode(1)
0.5
—
s
100 kHz mode
4.0
—
s
Device must operate at a
minimum of 1.5 MHz
400 kHz mode
0.6
—
s
Device must operate at a
minimum of 10 MHz
1 MHz mode(1)
0.5
—
s
100 kHz mode
—
300
ns
400 kHz mode
20 + 0.1 CB
300
ns
1 MHz mode(1)
—
100
ns
100 kHz mode
—
1000
ns
400 kHz mode
20 + 0.1 CB
300
ns
1 MHz mode(1)
—
300
ns
100 kHz mode
250
—
ns
400 kHz mode
100
—
ns
1 MHz mode(1)
100
—
ns
100 kHz mode
0
—
s
400 kHz mode
0
0.9
s
1 MHz mode(1)
0
0.3
s
100 kHz mode
4.7
—
s
400 kHz mode
0.6
—
s
1 MHz mode(1)
0.25
—
s
100 kHz mode
4.0
—
s
400 kHz mode
0.6
—
s
1 MHz mode(1)
0.25
—
s
100 kHz mode
4.7
—
s
400 kHz mode
0.6
—
s
1 MHz mode(1)
0.6
—
s
100 kHz mode
4000
—
ns
400 kHz mode
600
—
ns
1 MHz mode(1)
250
100 kHz mode
0
3500
ns
400 kHz mode
0
1000
ns
1 MHz mode(1)
0
350
ns
100 kHz mode
4.7
—
s
400 kHz mode
1.3
—
s
1 MHz mode(1)
0.5
—
s
—
400
pF
Bus Capacitive Loading
Conditions
—
—
CB is specified to be from
10 to 400 pF
CB is specified to be from
10 to 400 pF
—
—
Only relevant for Repeated
Start condition
After this period, the first
clock pulse is generated
—
—
ns
—
Time the bus must be free
before a new transmission
can start
—
Maximum pin capacitance = 10 pF for all I2Cx pins (for 1 MHz mode only).
DS70592B-page 266
Preliminary
 2009 Microchip Technology Inc.
PIC24HJXXXGPX06A/X08A/X10A
FIGURE 24-17:
ECAN™ MODULE I/O TIMING CHARACTERISTICS
CiTx Pin
(output)
New Value
Old Value
CA10 CA11
CiRx Pin
(input)
CA20
TABLE 24-34: ECAN™ MODULE I/O TIMING REQUIREMENTS
Standard Operating Conditions: 3.0V to 3.6V
(unless otherwise stated)
Operating temperature -40°C  TA  +85°C for Industrial
-40°C  TA  +125°C for Extended
AC CHARACTERISTICS
Param
No.
CA10
Characteristic(1)
Symbol
TioF
Port Output Fall Time
Min
Typ(2)
Max
Units
Conditions
—
—
—
ns
See parameter D032
CA11
TioR
Port Output Rise Time
—
—
—
ns
See parameter D031
CA20
Tcwf
Pulse-Width to Trigger
CAN Wake-up Filter
120
—
—
ns
—
Note 1:
2:
These parameters are characterized but not tested in manufacturing.
Data in “Typ” column is at 3.3V, 25°C unless otherwise stated. Parameters are for design guidance only
and are not tested.
 2009 Microchip Technology Inc.
Preliminary
DS70592B-page 267
PIC24HJXXXGPX06A/X08A/X10A
TABLE 24-35: ADC MODULE SPECIFICATIONS
AC CHARACTERISTICS
Param Symbo
No.
l
Characteristic
Standard Operating Conditions: 3.0V to 3.6V
(unless otherwise stated)
Operating temperature -40°C  TA  +85°C for Industrial
-40°C  TA  +125°C for Extended
Min.
Typ
Max.
Units
Lesser of
VDD + 0.3
or 3.6
V
VSS + 0.3
V
Conditions
Device Supply
AD01
AVDD
Module VDD Supply
AD02
AVSS
Module VSS Supply
AD05
VREFH
Reference Voltage High
Greater of
VDD – 0.3
or 3.0
—
VSS – 0.3
—
—
—
Reference Inputs
AD05a
AD06
VREFL
Reference Voltage Low
AD06a
AVSS + 2.7
—
AVDD
V
See Note 1
3.0
—
3.6
V
VREFH = AVDD
VREFL = AVSS = 0
AVSS
—
AVDD – 2.7
V
See Note 1
0
—
0
V
VREFH = AVDD
VREFL = AVSS = 0
AD07
VREF
Absolute Reference
Voltage
2.7
—
3.6
V
VREF = VREFH - VREFL
AD08
IREF
Current Drain
—
—
10
A
ADC off
AD08a IAD
Operating Current
—
—
7.0
2.7
9.0
3.2
mA
mA
10-bit ADC mode, See Note 1
12-bit ADC mode, See Note 1
AD12
VINH
Input Voltage Range VINH
VINL
—
VREFH
V
This voltage reflects Sample
and Hold Channels 0, 1, 2,
and 3 (CH0-CH3), positive
input
AD13
VINL
Input Voltage Range VINL
VREFL
—
AVSS + 1V
V
This voltage reflects Sample
and Hold Channels 0, 1, 2,
and 3 (CH0-CH3), negative
input
AD17
RIN
Recommended Impedance of Analog Voltage
Source
—
—
—
—
200
200


10-bit ADC
12-bit ADC
Analog Input
Note 1:
These parameters are not characterized or tested in manufacturing.
DS70592B-page 268
Preliminary
 2009 Microchip Technology Inc.
PIC24HJXXXGPX06A/X08A/X10A
TABLE 24-36: ADC MODULE SPECIFICATIONS (12-BIT MODE)
Standard Operating Conditions: 3.0V to 3.6V
(unless otherwise stated)
Operating temperature -40°C  TA  +85°C for Industrial
-40°C  TA  +125°C for Extended
AC CHARACTERISTICS
Param
No.
Symbol
Characteristic
Min.
Typ
Max.
Units
Conditions
ADC Accuracy (12-bit Mode) – Measurements with external VREF+/VREFAD20a
Nr
Resolution
12 data bits
bits
AD21a
INL
Integral Nonlinearity
-2
—
+2
LSb
VINL = AVSS = VREFL = 0V,
AVDD = VREFH = 3.6V
AD22a
DNL
Differential Nonlinearity
>-1
—
<1
LSb
VINL = AVSS = VREFL = 0V,
AVDD = VREFH = 3.6V
AD23a
GERR
Gain Error
1.25
3.4
10
LSb
VINL = AVSS = VREFL = 0V,
AVDD = VREFH = 3.6V
AD24a
EOFF
Offset Error
-0.2
0.9
5
LSb
VINL = AVSS = VREFL = 0V,
AVDD = VREFH = 3.6V
AD25a
—
Monotonicity
—
—
—
—
Guaranteed
ADC Accuracy (12-bit Mode) – Measurements with internal VREF+/VREFAD20a
Nr
Resolution
AD21a
INL
Integral Nonlinearity
-2
12 data bits
bits
—
+2
LSb
VINL = AVSS = 0V, AVDD = 3.6V
>-1
—
<1
LSb
VINL = AVSS = 0V, AVDD = 3.6V
2
10.5
20
LSb
VINL = AVSS = 0V, AVDD = 3.6V
AD22a
DNL
Differential Nonlinearity
AD23a
GERR
Gain Error
AD24a
EOFF
Offset Error
2
3.8
10
LSb
AD25a
—
Monotonicity
—
—
—
—
AD30a
THD
Total Harmonic Distortion
AD31a
SINAD
Signal to Noise and
Distortion
AD32a
SFDR
AD33a
AD34a
VINL = AVSS = 0V, AVDD = 3.6V
Guaranteed
Dynamic Performance (12-bit Mode)
—
—
-75
dB
—
68.5
69.5
—
dB
—
Spurious Free Dynamic
Range
80
—
—
dB
—
FNYQ
Input Signal Bandwidth
—
—
250
kHz
—
ENOB
Effective Number of Bits
11.09
11.3
—
bits
—
 2009 Microchip Technology Inc.
Preliminary
DS70592B-page 269
PIC24HJXXXGPX06A/X08A/X10A
TABLE 24-37: ADC MODULE SPECIFICATIONS (10-BIT MODE)
Standard Operating Conditions: 3.0V to 3.6V
(unless otherwise stated)
Operating temperature -40°C  TA  +85°C for Industrial
-40°C  TA  +125°C for Extended
AC CHARACTERISTICS
Param
No.
Symbol
Characteristic
Min.
Typ
Max.
Units
Conditions
ADC Accuracy (10-bit Mode) – Measurements with external VREF+/VREFAD20b
Nr
Resolution
10 data bits
bits
AD21b
INL
Integral Nonlinearity
-1.5
—
+1.5
LSb
VINL = AVSS = VREFL = 0V,
AVDD = VREFH = 3.6V
AD22b
DNL
Differential Nonlinearity
>-1
—
<1
LSb
VINL = AVSS = VREFL = 0V,
AVDD = VREFH = 3.6V
AD23b
GERR
Gain Error
0.4
3
6
LSb
VINL = AVSS = VREFL = 0V,
AVDD = VREFH = 3.6V
AD24b
EOFF
Offset Error
0.2
2
5
LSb
VINL = AVSS = VREFL = 0V,
AVDD = VREFH = 3.6V
AD25b
—
Monotonicity
—
—
—
—
Guaranteed
ADC Accuracy (10-bit Mode) – Measurements with internal VREF+/VREFAD20b
Nr
Resolution
AD21b
INL
Integral Nonlinearity
-1
10 data bits
—
+1
bits
LSb
VINL = AVSS = 0V, AVDD = 3.6V
AD22b
DNL
Differential Nonlinearity
>-1
—
<1
LSb
VINL = AVSS = 0V, AVDD = 3.6V
AD23b
GERR
Gain Error
3
7
15
LSb
VINL = AVSS = 0V, AVDD = 3.6V
AD24b
EOFF
Offset Error
1.5
3
7
LSb
AD25b
—
Monotonicity
—
—
—
—
AD30b
THD
Total Harmonic Distortion
—
—
-64
dB
—
AD31b
SINAD
Signal to Noise and
Distortion
57
58.5
—
dB
—
AD32b
SFDR
Spurious Free Dynamic
Range
72
—
—
dB
—
AD33b
FNYQ
Input Signal Bandwidth
—
—
550
kHz
—
AD34b
ENOB
Effective Number of Bits
9.16
9.4
—
bits
—
VINL = AVSS = 0V, AVDD = 3.6V
Guaranteed
Dynamic Performance (10-bit Mode)
DS70592B-page 270
Preliminary
 2009 Microchip Technology Inc.
PIC24HJXXXGPX06A/X08A/X10A
FIGURE 24-18:
ADC CONVERSION (12-BIT MODE) TIMING CHARACTERISTICS
(ASAM = 0, SSRC<2:0> = 000)
AD50
ADCLK
Instruction
Execution
Set SAMP
Clear SAMP
SAMP
AD61
AD60
TSAMP
AD55
DONE
AD1IF
1
2
3
4
5
6
7
8
9
1 Software sets AD1CON. SAMP to start sampling.
4 Sampling ends, conversion sequence starts.
2 Sampling starts after discharge period. TSAMP is described in
Section 28. “Analog-to-Digital Converter (ADC) without DMA”
(DS70249) in the “dsPIC33F/PIC24H Family Reference Manual”.
Please see the Microchip web site (www.microchip.com)
for the latest dsPIC33F/PIC24H Family Reference Manual sections.
5 Convert bit 11.
3 Software clears AD1CON. SAMP to start conversion.
 2009 Microchip Technology Inc.
Preliminary
6 Convert bit 10.
7 Convert bit 1.
8 Convert bit 0.
9 One TAD for end of conversion.
DS70592B-page 271
PIC24HJXXXGPX06A/X08A/X10A
TABLE 24-38: ADC CONVERSION (12-BIT MODE) TIMING REQUIREMENTS
Standard Operating Conditions: 3.0V to 3.6V
(unless otherwise stated)
Operating temperature -40°C  TA  +85°C for Industrial
-40°C  TA  +125°C for Extended
AC CHARACTERISTICS
Param
No.
Symbol
Characteristic
Min.
Typ(2)
Max.
Units
Conditions
Clock Parameters(1)
AD50
TAD
ADC Clock Period
AD51
tRC
ADC Internal RC Oscillator
Period
117.6
—
—
ns
—
—
250
—
ns
—
Conversion Rate
AD55
tCONV
Conversion Time
—
14 TAD
ns
—
AD56
FCNV
Throughput Rate
—
—
500
ksps
—
AD57
TSAMP
Sample Time
3 TAD
—
—
—
—
Timing Parameters
AD60
tPCS
Conversion Start from Sample
Trigger(2)
2.0 TAD
—
3.0 TAD
—
Auto convert trigger not
selected
AD61
tPSS
Sample Start from Setting
Sample (SAMP) bit(2)
2.0 TAD
—
3.0 TAD
—
—
AD62
tCSS
Conversion Completion to
Sample Start (ASAM = 1)(2)
—
0.5 TAD
—
—
—
AD63
tDPU
Time to Stabilize Analog Stage
from ADC Off to ADC On(2,3)
—
—
20
s
—
Note 1:
2:
3:
Because the sample caps eventually loses charge, clock rates below 10 kHz may affect linearity
performance, especially at elevated temperatures.
These parameters are characterized but not tested in manufacturing.
tDPU is the time required for the ADC module to stabilize when it is turned on (AD1CON1<ADON> = 1).
During this time, the ADC result is indeterminate.
DS70592B-page 272
Preliminary
 2009 Microchip Technology Inc.
PIC24HJXXXGPX06A/X08A/X10A
FIGURE 24-19:
ADC CONVERSION (10-BIT MODE) TIMING CHARACTERISTICS
(CHPS<1:0> = 01, SIMSAM = 0, ASAM = 0, SSRC<2:0> = 000)
AD50
ADCLK
Instruction
Execution Set SAMP
Clear SAMP
SAMP
AD61
AD60
AD55
TSAMP
AD55
DONE
AD1IF
1
2
3
4
5
6
7
8
5
6
7
8
1 – Software sets AD1CON. SAMP to start sampling.
2 – Sampling starts after discharge period. TSAMP is described in Section 28. “Analog-to-Digital Converter (ADC)
without DMA” (DS70249) in the “dsPIC33F/PIC24H Family Reference Manual”.
3 – Software clears AD1CON. SAMP to start conversion.
4 – Sampling ends, conversion sequence starts.
5 – Convert bit 9.
6 – Convert bit 8.
7 – Convert bit 0.
8 – One TAD for end of conversion.
FIGURE 24-20:
ADC CONVERSION (10-BIT MODE) TIMING CHARACTERISTICS (CHPS<1:0> = 01,
SIMSAM = 0, ASAM = 1, SSRC<2:0> = 111, SAMC<4:0> = 00001)
AD50
ADCLK
Instruction
Set ADON
Execution
SAMP
TSAMP
AD55
TSAMP
AD55
AD55
AD1IF
DONE
1
2
3
4
5
6
7
3
4
5
6
8
1 – Software sets AD1CON. ADON to start AD operation.
5 – Convert bit 0.
2 – Sampling starts after discharge period. TSAMP is described in
Section 28. “Analog-to-Digital Converter (ADC) without DMA”
(DS70249) in the “dsPIC33F/PIC24H Family Reference Manual'.
3 – Convert bit 9.
6 – One TAD for end of conversion.
7 – Begin conversion of next channel.
8 – Sample for time specified by SAMC<4:0>.
4 – Convert bit 8.
 2009 Microchip Technology Inc.
Preliminary
DS70592B-page 273
PIC24HJXXXGPX06A/X08A/X10A
TABLE 24-39: ADC CONVERSION (10-BIT MODE) TIMING REQUIREMENTS
Standard Operating Conditions: 3.0V to 3.6V
(unless otherwise stated)
Operating temperature -40°C  TA  +85°C for Industrial
-40°C  TA  +125°C for Extended
AC CHARACTERISTICS
Param
Symbol
No.
Characteristic
Min.
Typ(1)
Max.
Units
Conditions
Clock Parameters
AD50
TAD
ADC Clock Period
76
—
—
ns
—
AD51
tRC
ADC Internal RC Oscillator Period
—
250
—
ns
—
Conversion Rate
AD55
tCONV
Conversion Time
—
12 TAD
—
—
—
AD56
FCNV
Throughput Rate
—
—
1.1
Msps
—
AD57
TSAMP
Sample Time
2 TAD
—
—
—
—
Timing Parameters
AD60
tPCS
Conversion Start from Sample
Trigger(2)
2.0 TAD
—
3.0 TAD
—
AD61
tPSS
Sample Start from Setting
Sample (SAMP) bit(2)
2.0 TAD
—
3.0 TAD
—
—
AD62
tCSS
Conversion Completion to
Sample Start (ASAM = 1)(2)
—
0.5 TAD
—
—
—
AD63
tDPU
Time to Stabilize Analog Stage
from ADC Off to ADC On(2,3)
—
—
20
s
—
Note 1:
2:
3:
Auto-Convert Trigger
not selected
These parameters are characterized but not tested in manufacturing.
Because the sample caps eventually loses charge, clock rates below 10 kHz may affect linearity
performance, especially at elevated temperatures.
tDPU is the time required for the ADC module to stabilize when it is turned on (AD1CON1<ADON> = 1).
During this time, the ADC result is indeterminate.
DS70592B-page 274
Preliminary
 2009 Microchip Technology Inc.
PIC24HJXXXGPX06A/X08A/X10A
25.0
HIGH TEMPERATURE ELECTRICAL CHARACTERISTICS
This section provides an overview of PIC24HJXXXGPX06A/X08A/X10A electrical characteristics for devices operating
in an ambient temperature range of -40°C to +140°C.
Note:
Programming of the Flash memory is not allowed above 125°C.
The specifications between -40°C to +140°C are identical to those shown in Section 24.0 “Electrical Characteristics”
for operation between -40°C to +125°C, with the exception of the parameters listed in this section.
Parameters in this section begin with an H, which denotes High temperature. For example, parameter DC10 in
Section 24.0 “Electrical Characteristics” is the Industrial and Extended temperature equivalent of HDC10.
Absolute maximum ratings for the PIC24HJXXXGPX06A/X08A/X10A high temperature devices are listed below.
Exposure to these maximum rating conditions for extended periods can affect device reliability. Functional operation of
the device at these or any other conditions above the parameters indicated in the operation listings of this specification
is not implied.
Absolute Maximum Ratings(1)
Ambient temperature under bias(4) .........................................................................................................-40°C to +140°C
Storage temperature .............................................................................................................................. -65°C to +150°C
Voltage on VDD with respect to VSS ......................................................................................................... -0.3V to +4.0V
Voltage on any pin that is not 5V tolerant with respect to VSS(5) .................................................... -0.3V to (VDD + 0.3V)
Voltage on any 5V tolerant pin with respect to VSS when VDD < 3.0V(5) ....................................... -0.3V to (VDD + 0.3V)
Voltage on any 5V tolerant pin with respect to VSS when VDD  3.0V(5) .................................................... -0.3V to 5.6V
Voltage on VCAP/VDDCORE with respect to VSS ....................................................................................... 2.25V to 2.75V
Maximum current out of VSS pin .............................................................................................................................60 mA
Maximum current into VDD pin(2) .............................................................................................................................60 mA
Maximum junction temperature............................................................................................................................. +145°C
Maximum output current sunk by any I/O pin(3) ........................................................................................................1 mA
Maximum output current sourced by any I/O pin(3) ...................................................................................................1 mA
Maximum current sunk by all ports combined ........................................................................................................10 mA
Maximum current sourced by all ports combined(2) ................................................................................................10 mA
Note 1: Stresses above those listed under “Absolute Maximum Ratings” can cause permanent damage to the
device. This is a stress rating only, and functional operation of the device at those or any other conditions
above those indicated in the operation listings of this specification is not implied. Exposure to maximum
rating conditions for extended periods can affect device reliability.
2: Maximum allowable current is a function of device maximum power dissipation (see Table 25-2).
3: Unlike devices at 125°C and below, the specifications in this section also apply to the CLKOUT, VREF+,
VREF-, SCLx, SDAx, PGCx, and PGDx pins.
4: AEC-Q100 reliability testing for devices intended to operate at 150°C is 1,000 hours. Any design in which
the total operating time from 125°C to 150°C will be greater than 1,000 hours is not warranted without prior
written approval from Microchip Technology Inc.
5: Refer to the “Pin Diagrams” section for 5V tolerant pins.
 2009 Microchip Technology Inc.
Preliminary
DS70592B-page 275
PIC24HJXXXGPX06A/X08A/X10A
25.1
High Temperature DC Characteristics
TABLE 25-1:
OPERATING MIPS VS. VOLTAGE
Max MIPS
Characteristic
TABLE 25-2:
VDD Range
(in Volts)
Temperature Range
(in °C)
3.0V to 3.6V
-40°C to +140°C
PIC24HJXXXGPX06A/X08A/
X10A
20
THERMAL OPERATING CONDITIONS
Rating
Symbol
Min
Typ
Max
Unit
Operating Junction Temperature Range
TJ
-40
—
+145
°C
Operating Ambient Temperature Range
TA
-40
—
+140
°C
High Temperature Devices
Power Dissipation:
Internal chip power dissipation:
PINT = VDD x (IDD -  IOH)
PD
PINT + PI/O
W
PDMAX
(TJ - TA)/JA
W
I/O Pin Power Dissipation:
I/O =  ({VDD - VOH} x IOH) +  (VOL x IOL)
Maximum Allowed Power Dissipation
TABLE 25-3:
DC TEMPERATURE AND VOLTAGE SPECIFICATIONS
Standard Operating Conditions: 3.0V to 3.6V
(unless otherwise stated)
Operating temperature -40°C  TA  +140°C for High Temperature
DC CHARACTERISTICS
Parameter
No.
Symbol
Characteristic
Min
Typ
Max
Units
3.0
3.3
3.6
V
Conditions
Operating Voltage
HDC10
Supply Voltage
VDD
TABLE 25-4:
—
DC CHARACTERISTICS: POWER-DOWN CURRENT (IPD)
Standard Operating Conditions: 3.0V to 3.6V
(unless otherwise stated)
Operating temperature -40°C  TA  +140°C for High Temperature
DC CHARACTERISTICS
Parameter
No.
-40°C to +140°C
Typical
Max
Units
Conditions
Power-Down Current (IPD)
HDC60e
250
2000
A
+140°C
3.3V
Base Power-Down Current(1,3)
HDC61c
3
5
A
+140°C
3.3V
Watchdog Timer Current: IWDT(2,4)
Note 1:
2:
3:
4:
Base IPD is measured with all peripherals and clocks shut down. All I/Os are configured as inputs and
pulled to VSS. WDT, etc., are all switched off, and VREGS (RCON<8>) = 1.
The  current is the additional current consumed when the module is enabled. This current should be
added to the base IPD current.
These currents are measured on the device containing the most memory in this family.
These parameters are characterized, but are not tested in manufacturing.
DS70592B-page 276
Preliminary
 2009 Microchip Technology Inc.
PIC24HJXXXGPX06A/X08A/X10A
TABLE 25-5:
DC CHARACTERISTICS: DOZE CURRENT (IDOZE)
Standard Operating Conditions: 3.0V to 3.6V
(unless otherwise stated)
Operating temperature -40°C  TA  +140°C for High Temperature
DC CHARACTERISTICS
Parameter
No.
Typical(1)
Max
Doze
Ratio
Units
HDC72a
39
45
1:2
mA
HDC72f
18
25
1:64
mA
18
25
1:128
mA
HDC72g
Note 1:
+140°C
3.3V
20 MIPS
Parameters with Doze ratios of 1:2 and 1:64 are characterized, but are not tested in manufacturing.
TABLE 25-6:
DC CHARACTERISTICS: I/O PIN OUTPUT SPECIFICATIONS
Standard Operating Conditions: 3.0V to 3.6V
(unless otherwise stated)
Operating temperature -40°C  TA  +140°C for High Temperature
DC CHARACTERISTICS
Param
No.
Conditions
Symbol
Characteristic
Min
Typ
Max
Units
Conditions
Output Low Voltage
VOL
HDO10
I/O ports
—
—
0.4
V
IOL = 1 mA, VDD = 3.3V
HDO16
OSC2/CLKO
—
—
0.4
V
IOL = 1 mA, VDD = 3.3V
Output High Voltage
VOH
HDO20
I/O ports
2.40
—
—
V
IOH = -1 mA, VDD = 3.3V
HDO26
OSC2/CLKO
2.41
—
—
V
IOH = -1 mA, VDD = 3.3V
TABLE 25-7:
DC CHARACTERISTICS: PROGRAM MEMORY
DC CHARACTERISTICS
Param
Symbol
No.
Characteristic(1)
Standard Operating Conditions: 3.0V to 3.6V
(unless otherwise stated)
Operating temperature -40°C  TA  +140°C for High Temperature
Min
Typ
Max
Units
Conditions
10,000
—
—
E/W
-40C to +140C(2)
20
—
—
Year
1000 E/W cycles or less and no
other specifications are violated
Program Flash Memory
HD130 EP
Cell Endurance
HD134 TRETD
Characteristic Retention
Note 1:
2:
These parameters are assured by design, but are not characterized or tested in manufacturing.
Programming of the Flash memory is not allowed above 125°C.
 2009 Microchip Technology Inc.
Preliminary
DS70592B-page 277
PIC24HJXXXGPX06A/X08A/X10A
25.2
AC Characteristics and Timing
Parameters
The information contained in this section defines
PIC24HJXXXGPX06A/X08A/X10A AC characteristics
and timing parameters for high temperature devices.
However, all AC timing specifications in this section are
the same as those in Section 24.2 “AC
Characteristics and Timing Parameters”, with the
exception of the parameters listed in this section.
Parameters in this section begin with an H, which
denotes High temperature. For example, parameter
OS53 in Section 24.2 “AC Characteristics and
Timing Parameters” is the Industrial and Extended
temperature equivalent of HOS53.
TABLE 25-8:
TEMPERATURE AND VOLTAGE SPECIFICATIONS – AC
AC CHARACTERISTICS
FIGURE 25-1:
Standard Operating Conditions: 3.0V to 3.6V
(unless otherwise stated)
Operating temperature -40°C  TA  +140°C for High Temperature
Operating voltage VDD range as described in Table 25-1.
LOAD CONDITIONS FOR DEVICE TIMING SPECIFICATIONS
Load Condition 1 – for all pins except OSC2
Load Condition 2 – for OSC2
VDD/2
CL
Pin
RL
VSS
CL
Pin
RL = 464
CL = 50 pF for all pins except OSC2
15 pF for OSC2 output
VSS
TABLE 25-9:
PLL CLOCK TIMING SPECIFICATIONS
Standard Operating Conditions: 3.0V to 3.6V (unless otherwise stated)
AC
CHARACTERISTICS Operating temperature -40°C  TA  +140°C for High Temperature
Param
No.
Symbol
Characteristic
CLKO Stability (Jitter)(1)
Min
Typ
Max
Units
-5
0.5
5
%
HOS53
DCLK
Note 1:
These parameters are characterized, but are not tested in manufacturing.
DS70592B-page 278
Preliminary
Conditions
Measured over 100 ms
period
 2009 Microchip Technology Inc.
PIC24HJXXXGPX06A/X08A/X10A
TABLE 25-10: SPIx MASTER MODE (CKE = 0) TIMING REQUIREMENTS
Standard Operating Conditions: 3.0V to 3.6V (unless otherwise stated)
AC
CHARACTERISTICS Operating temperature -40°C  TA  +140°C for High Temperature
Param
No.
Characteristic(1)
Symbol
Min
Typ
Max
Units
Conditions
HSP35
TscH2doV, SDOx Data Output Valid after
TscL2doV SCKx Edge
—
10
25
ns
—
HSP40
TdiV2scH, Setup Time of SDIx Data Input
TdiV2scL to SCKx Edge
28
—
—
ns
—
HSP41
TscH2diL,
TscL2diL
35
—
—
ns
—
Note 1:
These parameters are characterized but not tested in manufacturing.
Hold Time of SDIx Data Input
to SCKx Edge
TABLE 25-11: SPIx MODULE MASTER MODE (CKE = 1) TIMING REQUIREMENTS
Standard Operating Conditions: 3.0V to 3.6V (unless otherwise stated)
AC
CHARACTERISTICS Operating temperature -40°C  TA  +140°C for High Temperature
Param
No.
Characteristic(1)
Symbol
Min
Typ
Max
Units
Conditions
HSP35
TscH2doV, SDOx Data Output Valid after
TscL2doV SCKx Edge
—
10
25
ns
—
HSP36
TdoV2sc,
TdoV2scL
35
—
—
ns
—
HSP40
TdiV2scH, Setup Time of SDIx Data Input
TdiV2scL to SCKx Edge
28
—
—
ns
—
HSP41
TscH2diL,
TscL2diL
35
—
—
ns
—
Note 1:
SDOx Data Output Setup to
First SCKx Edge
Hold Time of SDIx Data Input
to SCKx Edge
These parameters are characterized but not tested in manufacturing.
 2009 Microchip Technology Inc.
Preliminary
DS70592B-page 279
PIC24HJXXXGPX06A/X08A/X10A
TABLE 25-12: SPIx MODULE SLAVE MODE (CKE = 0) TIMING REQUIREMENTS
Standard Operating Conditions: 3.0V to 3.6V (unless otherwise stated)
AC
CHARACTERISTICS Operating temperature -40°C  TA  +140°C for High Temperature
Param
No.
Symbol
Characteristic(1)
Min
Typ
Max
Units
Conditions
HSP35
TscH2doV,
TscL2doV
SDOx Data Output Valid after
SCKx Edge
—
—
35
ns
—
HSP40
TdiV2scH,
TdiV2scL
Setup Time of SDIx Data Input
to SCKx Edge
25
—
—
ns
—
HSP41
TscH2diL,
TscL2diL
Hold Time of SDIx Data Input to
SCKx Edge
25
—
—
ns
—
HSP51
TssH2doZ
SSx  to SDOx Output
High-Impedance
15
—
55
ns
Note 1:
2:
See Note 2
These parameters are characterized but not tested in manufacturing.
Assumes 50 pF load on all SPIx pins.
TABLE 25-13: SPIx MODULE SLAVE MODE (CKE = 1) TIMING REQUIREMENTS
AC
CHARACTERISTICS
Param
No.
Symbol
Standard Operating Conditions: 3.0V to 3.6V (unless otherwise stated)
Operating temperature -40°C  TA  +140°C for High Temperature
Characteristic(1)
Min
Typ
Max
Units
Conditions
HSP35
TscH2doV, SDOx Data Output Valid after
TscL2doV SCKx Edge
—
—
35
ns
—
HSP40
TdiV2scH, Setup Time of SDIx Data Input
TdiV2scL to SCKx Edge
25
—
—
ns
—
HSP41
TscH2diL,
TscL2diL
Hold Time of SDIx Data Input
to SCKx Edge
25
—
—
ns
—
HSP51
TssH2doZ
SSx  to SDOX Output
High-Impedance
15
—
55
ns
HSP60
TssL2doV
SDOx Data Output Valid after
SSx Edge
—
—
55
ns
Note 1:
2:
These parameters are characterized but not tested in manufacturing.
Assumes 50 pF load on all SPIx pins.
DS70592B-page 280
Preliminary
See Note 2
—
 2009 Microchip Technology Inc.
PIC24HJXXXGPX06A/X08A/X10A
TABLE 25-14: ADC MODULE SPECIFICATIONS
AC
CHARACTERISTICS
Param
No.
Symbol
Standard Operating Conditions: 3.0V to 3.6V (unless otherwise stated)
Operating temperature -40°C  TA  +140°C for High Temperature
Characteristic
Min
Typ
Max
Units
600
50
A
A
Conditions
Reference Inputs
HAD08
Note 1:
2:
Current Drain
IREF
—
—
250
—
ADC operating, See Note 1
ADC off, See Note 1
These parameters are not characterized or tested in manufacturing.
These parameters are characterized, but are not tested in manufacturing.
TABLE 25-15: ADC MODULE SPECIFICATIONS (12-BIT MODE)
Standard Operating Conditions: 3.0V to 3.6V (unless otherwise stated)
AC
CHARACTERISTICS Operating temperature -40°C  TA  +140°C for High Temperature
Param
No.
Symbol
Characteristic
Min
Typ
Max
Units
Conditions
ADC Accuracy (12-bit Mode) – Measurements with External VREF+/VREF-(1)
HAD20a
Nr
Resolution
HAD21a
INL
Integral Nonlinearity
12 data bits
HAD22a
DNL
Differential Nonlinearity
HAD23a
GERR
HAD24a
EOFF
bits
—
-2
—
+2
LSb
VINL = AVSS = VREFL = 0V,
AVDD = VREFH = 3.6V
> -1
—
<1
LSb
VINL = AVSS = VREFL = 0V,
AVDD = VREFH = 3.6V
Gain Error
-2
—
10
LSb
VINL = AVSS = VREFL = 0V,
AVDD = VREFH = 3.6V
Offset Error
-3
—
5
LSb
VINL = AVSS = VREFL = 0V,
AVDD = VREFH = 3.6V
ADC Accuracy (12-bit Mode) – Measurements with Internal VREF+/VREF-(1)
HAD20a
Nr
Resolution
HAD21a
INL
Integral Nonlinearity
12 data bits
HAD22a
DNL
Differential Nonlinearity
HAD23a
GERR
Gain Error
HAD24a
EOFF
Offset Error
-2
bits
—
LSb
VINL = AVSS = 0V, AVDD = 3.6V
—
+2
> -1
—
<1
LSb
VINL = AVSS = 0V, AVDD = 3.6V
2
—
20
LSb
VINL = AVSS = 0V, AVDD = 3.6V
2
—
10
LSb
VINL = AVSS = 0V, AVDD = 3.6V
Dynamic Performance (12-bit Mode)(2)
HAD33a
FNYQ
Note 1:
2:
These parameters are characterized, but are tested at 20 ksps only.
These parameters are characterized by similarity, but are not tested in manufacturing.
Input Signal Bandwidth
 2009 Microchip Technology Inc.
—
—
Preliminary
200
kHz
—
DS70592B-page 281
PIC24HJXXXGPX06A/X08A/X10A
TABLE 25-16: ADC MODULE SPECIFICATIONS (10-BIT MODE)
Standard Operating Conditions: 3.0V to 3.6V (unless otherwise stated)
AC
CHARACTERISTICS Operating temperature -40°C  TA  +140°C for High Temperature
Param
No.
Symbol
Characteristic
Min
Typ
Max
Units
Conditions
ADC Accuracy (10-bit Mode) – Measurements with External VREF+/VREF-(1)
HAD20b
Nr
Resolution
HAD21b
INL
Integral Nonlinearity
10 data bits
HAD22b
DNL
Differential Nonlinearity
HAD23b
GERR
HAD24b
EOFF
bits
—
-3
—
3
LSb
VINL = AVSS = VREFL = 0V,
AVDD = VREFH = 3.6V
> -1
—
<1
LSb
VINL = AVSS = VREFL = 0V,
AVDD = VREFH = 3.6V
Gain Error
-5
—
6
LSb
VINL = AVSS = VREFL = 0V,
AVDD = VREFH = 3.6V
Offset Error
-1
—
5
LSb
VINL = AVSS = VREFL = 0V,
AVDD = VREFH = 3.6V
ADC Accuracy (10-bit Mode) – Measurements with Internal VREF+/VREF-(1)
HAD20b
Nr
Resolution
HAD21b
INL
Integral Nonlinearity
10 data bits
HAD22b
DNL
Differential Nonlinearity
HAD23b
GERR
Gain Error
HAD24b
EOFF
Offset Error
bits
—
-2
—
2
LSb
VINL = AVSS = 0V, AVDD = 3.6V
> -1
—
<1
LSb
VINL = AVSS = 0V, AVDD = 3.6V
-5
—
15
LSb
VINL = AVSS = 0V, AVDD = 3.6V
-1.5
—
7
LSb
VINL = AVSS = 0V, AVDD = 3.6V
Dynamic Performance (10-bit Mode)(2)
HAD33b
FNYQ
Note 1:
2:
These parameters are characterized, but are tested at 20 ksps only.
These parameters are characterized by similarity, but are not tested in manufacturing.
DS70592B-page 282
Input Signal Bandwidth
—
—
Preliminary
400
kHz
—
 2009 Microchip Technology Inc.
PIC24HJXXXGPX06A/X08A/X10A
TABLE 25-17: ADC CONVERSION (12-BIT MODE) TIMING REQUIREMENTS
Standard Operating Conditions: 3.0V to 3.6V (unless otherwise stated)
AC
CHARACTERISTICS Operating temperature -40°C  TA  +140°C for High Temperature
Param
No.
Symbol
Characteristic
Min
Typ
Max
Units
Conditions
—
—
ns
—
—
400
Ksps
—
Clock Parameters
HAD50
TAD
ADC Clock Period(1)
HAD56
FCNV
Throughput Rate(1)
147
Conversion Rate
Note 1:
—
These parameters are characterized but not tested in manufacturing.
TABLE 25-18: ADC CONVERSION (10-BIT MODE) TIMING REQUIREMENTS
Standard Operating Conditions: 3.0V to 3.6V (unless otherwise stated)
AC
CHARACTERISTICS Operating temperature -40°C  TA  +140°C for High Temperature
Param
No.
Symbol
Characteristic
Min
Typ
Max
Units
Conditions
—
ns
—
800
Ksps
—
Clock Parameters
HAD50
TAD
ADC Clock Period(1)
HAD56
FCNV
Throughput Rate(1)
Note 1:
These parameters are characterized but not tested in manufacturing.
104
—
Conversion Rate
 2009 Microchip Technology Inc.
—
Preliminary
—
DS70592B-page 283
PIC24HJXXXGPX06A/X08A/X10A
NOTES:
DS70592B-page 284
Preliminary
 2009 Microchip Technology Inc.
PIC24HJXXXGPX06A/X08A/X10A
26.0
PACKAGING INFORMATION
26.1
Package Marking Information
64-Lead QFN (9x9x0.9mm)
Example
XXXXXXXXXX
XXXXXXXXXX
24HJ64GP
206A-I/MR e3
YYWWNNN
0610017
64-Lead TQFP (10x10x1 mm)
Example
XXXXXXXXXX
XXXXXXXXXX
XXXXXXXXXX
YYWWNNN
PIC24HJ
256GP706A
-I/PT e3
0510017
100-Lead TQFP (12x12x1 mm)
Example
XXXXXXXXXXXX
XXXXXXXXXXXX
YYWWNNN
PIC24HJ256
GP710A-I/PT e3
0510017
100-Lead TQFP (14x14x1 mm)
Example
XXXXXXXXXXXX
XXXXXXXXXXXX
YYWWNNN
Legend: XX...X
Y
YY
WW
NNN
e3
*
Note:
PIC24HJ256
GP710A-I/PF e3
0510017
Customer-specific information
Year code (last digit of calendar year)
Year code (last 2 digits of calendar year)
Week code (week of January 1 is week ‘01’)
Alphanumeric traceability code
Pb-free JEDEC designator for Matte Tin (Sn)
This package is Pb-free. The Pb-free JEDEC designator ( e3 )
can be found on the outer packaging for this package.
In the event the full Microchip part number cannot be marked on one line, it will
be carried over to the next line, thus limiting the number of available
characters for customer-specific information.
 2009 Microchip Technology Inc.
Preliminary
DS70592B-page 285
PIC24HJXXXGPX06A/X08A/X10A
26.2
Note:
Package Details
For the most current package drawings, please see the Microchip Packaging Specification located at
http://www.microchip.com/packaging
DS70592B-page 286
Preliminary
 2009 Microchip Technology Inc.
PIC24HJXXXGPX06A/X08A/X10A
Note:
For the most current package drawings, please see the Microchip Packaging Specification located at
http://www.microchip.com/packaging
 2009 Microchip Technology Inc.
Preliminary
DS70592B-page 287
PIC24HJXXXGPX06A/X08A/X10A
64-Lead Plastic Thin Quad Flatpack (PT) – 10x10x1 mm Body, 2.00 mm Footprint [TQFP]
Note:
For the most current package drawings, please see the Microchip Packaging Specification located at
http://www.microchip.com/packaging
D
D1
E
e
E1
N
b
NOTE 1
123
NOTE 2
α
A
φ
c
A2
β
A1
L
L1
Units
Dimension Limits
Number of Leads
MILLIMETERS
MIN
N
NOM
MAX
64
Lead Pitch
e
Overall Height
A
–
0.50 BSC
–
Molded Package Thickness
A2
0.95
1.00
1.05
Standoff
A1
0.05
–
0.15
Foot Length
L
0.45
0.60
0.75
Footprint
L1
1.20
1.00 REF
Foot Angle
φ
Overall Width
E
12.00 BSC
Overall Length
D
12.00 BSC
Molded Package Width
E1
10.00 BSC
Molded Package Length
D1
10.00 BSC
0°
3.5°
7°
Lead Thickness
c
0.09
–
0.20
Lead Width
b
0.17
0.22
0.27
Mold Draft Angle Top
α
11°
12°
13°
Mold Draft Angle Bottom
β
11°
12°
13°
Notes:
1. Pin 1 visual index feature may vary, but must be located within the hatched area.
2. Chamfers at corners are optional; size may vary.
3. Dimensions D1 and E1 do not include mold flash or protrusions. Mold flash or protrusions shall not exceed 0.25 mm per side.
4. Dimensioning and tolerancing per ASME Y14.5M.
BSC: Basic Dimension. Theoretically exact value shown without tolerances.
REF: Reference Dimension, usually without tolerance, for information purposes only.
Microchip Technology Drawing C04-085B
DS70592B-page 288
Preliminary
 2009 Microchip Technology Inc.
PIC24HJXXXGPX06A/X08A/X10A
!"#$%
&
' (
!"
#!$!%&'#(##!
)%*!
!&!
!!+,,'''"
",%
 2009 Microchip Technology Inc.
Preliminary
DS70592B-page 289
PIC24HJXXXGPX06A/X08A/X10A
100-Lead Plastic Thin Quad Flatpack (PT) – 12x12x1 mm Body, 2.00 mm Footprint [TQFP]
Note:
For the most current package drawings, please see the Microchip Packaging Specification located at
http://www.microchip.com/packaging
D
D1
e
E
E1
N
b
NOTE 1
1 23
NOTE 2
α
c
A
φ
L
β
A1
Units
Dimension Limits
Number of Leads
A2
L1
MILLIMETERS
MIN
N
NOM
MAX
100
Lead Pitch
e
Overall Height
A
–
0.40 BSC
–
Molded Package Thickness
A2
0.95
1.00
1.05
Standoff
A1
0.05
–
0.15
Foot Length
L
0.45
0.60
0.75
Footprint
L1
1.20
1.00 REF
Foot Angle
φ
Overall Width
E
14.00 BSC
Overall Length
D
14.00 BSC
Molded Package Width
E1
12.00 BSC
Molded Package Length
D1
12.00 BSC
0°
3.5°
7°
Lead Thickness
c
0.09
–
0.20
Lead Width
b
0.13
0.18
0.23
Mold Draft Angle Top
α
11°
12°
13°
Mold Draft Angle Bottom
β
11°
12°
13°
Notes:
1. Pin 1 visual index feature may vary, but must be located within the hatched area.
2. Chamfers at corners are optional; size may vary.
3. Dimensions D1 and E1 do not include mold flash or protrusions. Mold flash or protrusions shall not exceed 0.25 mm per side.
4. Dimensioning and tolerancing per ASME Y14.5M.
BSC: Basic Dimension. Theoretically exact value shown without tolerances.
REF: Reference Dimension, usually without tolerance, for information purposes only.
Microchip Technology Drawing C04-100B
DS70592B-page 290
Preliminary
 2009 Microchip Technology Inc.
PIC24HJXXXGPX06A/X08A/X10A
## !"#$%
&
' (
!"
#!$!%&'#(##!
)%*!
!&!
!!+,,'''"
",%
 2009 Microchip Technology Inc.
Preliminary
DS70592B-page 291
PIC24HJXXXGPX06A/X08A/X10A
100-Lead Plastic Thin Quad Flatpack (PF) – 14x14x1 mm Body, 2.00 mm Footprint [TQFP]
Note:
For the most current package drawings, please see the Microchip Packaging Specification located at
http://www.microchip.com/packaging
D
D1
e
E1
E
b
N
α
NOTE 1
1 23
NOTE 2
A
φ
c
β
A2
A1
L
L1
Units
Dimension Limits
Number of Leads
MILLIMETERS
MIN
N
NOM
MAX
100
Lead Pitch
e
Overall Height
A
–
0.50 BSC
–
Molded Package Thickness
A2
0.95
1.00
1.05
Standoff
A1
0.05
–
0.15
Foot Length
L
0.45
0.60
0.75
Footprint
L1
1.20
1.00 REF
Foot Angle
φ
Overall Width
E
16.00 BSC
Overall Length
D
16.00 BSC
Molded Package Width
E1
14.00 BSC
Molded Package Length
D1
14.00 BSC
0°
3.5°
7°
Lead Thickness
c
0.09
–
0.20
Lead Width
b
0.17
0.22
0.27
Mold Draft Angle Top
α
11°
12°
13°
Mold Draft Angle Bottom
β
11°
12°
13°
Notes:
1. Pin 1 visual index feature may vary, but must be located within the hatched area.
2. Chamfers at corners are optional; size may vary.
3. Dimensions D1 and E1 do not include mold flash or protrusions. Mold flash or protrusions shall not exceed 0.25 mm per side.
4. Dimensioning and tolerancing per ASME Y14.5M.
BSC: Basic Dimension. Theoretically exact value shown without tolerances.
REF: Reference Dimension, usually without tolerance, for information purposes only.
Microchip Technology Drawing C04-110B
DS70592B-page 292
Preliminary
 2009 Microchip Technology Inc.
PIC24HJXXXGPX06A/X08A/X10A
!"#$%
&
' (
!"
#!$!%&'#(##!
)%*!
!&!
!!+,,'''"
",%
 2009 Microchip Technology Inc.
Preliminary
DS70592B-page 293
PIC24HJXXXGPX06A/X08A/X10A
NOTES:
DS70592B-page 294
Preliminary
 2009 Microchip Technology Inc.
PIC24HJXXXGPX06A/X08A/X10A
APPENDIX A:
MIGRATING FROM
PIC24HJXXXGPX06/
X08/X10 DEVICES TO
PIC24HJXXXGPX06A/
X08A/X10A DEVICES
PIC24HJXXXGPX06A/X08A/X10A
devices
were
designed to enhance the PIC24HJXXXGPX06/X08/
X10 families of devices.
In general, the PIC24HJXXXGPX06A/X08A/X10A
devices
are
backward-compatible
with
PIC24HJXXXGPX06/X08/X10 devices; however, manufacturing
differences
may
cause
PIC24HJXXXGPX06A/X08A/X10A devices to behave
differently from PIC24HJXXXGPX06/X08/X10 devices.
Therefore, complete system test and characterization
is recommended if PIC24HJXXXGPX06A/X08A/X10A
devices are used to replace PIC24HJXXXGPX06/X08/
X10 devices.
The following enhancements were introduced:
• Extended temperature support of up to +125ºC
• Enhanced Flash module with higher endurance
and retention
• New PLL Lock Enable configuration bit
• Added Timer5 trigger for ADC1 and Timer3 trigger
for ADC2
 2009 Microchip Technology Inc.
Preliminary
DS70592B-page 295
PIC24HJXXXGPX06A/X08A/X10A
APPENDIX B:
REVISION HISTORY
Revision B (October 2009)
The revision includes the following global update:
Revision A (April 2009)
• Added Note 2 to the shaded table that appears at
the beginning of each chapter. This new note
provides information regarding the availability of
registers and their associated bits
This is the initial release of this document.
This revision also includes minor typographical and
formatting changes throughout the data sheet text.
All other major changes are referenced by their
respective section in the following table.
TABLE B-1:
MAJOR SECTION UPDATES
Section Name
Update Description
“High-Performance, 16-Bit
Microcontrollers”
Added information on high temperature operation (see “Operating
Range:”).
Section 10.0 “Power-Saving Features”
Updated the last paragraph to clarify the number of cycles that occur
prior to the start of instruction execution (see Section 10.2.2 “Idle
Mode”).
Section 11.0 “I/O Ports”
Changed the reference to digital-only pins to 5V tolerant pins in the
second paragraph of Section 11.2 “Open-Drain Configuration”.
Section 18.0 “Universal Asynchronous
Receiver Transmitter (UART)”
Updated the two baud rate range features to: 10 Mbps to 38 bps at
40 MIPS.
Section 20.0 “10-Bit/12-Bit Analog-toDigital Converter (ADC)”
Updated the ADCx block diagram (see Figure 20-1).
Section 21.0 “Special Features”
Updated the second paragraph and removed the fourth paragraph in
Section 21.1 “Configuration Bits”.
Updated the Device Configuration Register Map (see Table 21-1).
Section 24.0 “Electrical Characteristics”
Updated the Absolute Maximum Ratings for high temperature and
added Note 4.
Updated Power-Down Current parameters DC60d, DC60a, DC60b,
and DC60d (see Table 24-7).
Added I2Cx Bus Data Timing Requirements (Master Mode)
parameter IM51 (see Table 24-32).
Updated the SPIx Module Slave Mode (CKE = 1) Timing
Characteristics (see Figure 24-12).
Updated the Internal LPRC Accuracy parameters (see Table 24-18
and Table 24-19).
Updated the ADC Module Specifications (12-bit Mode) parameters
AD23a and AD24a (see Table 24-36).
Updated the ADC Module Specifications (10-bit Mode) parameters
AD23b and AD24b (see Table 24-37).
Section 25.0 “High Temperature Electrical
Characteristics”
Added new chapter with high temperature specifications.
“Product Identification System”
Added the “H” definition for high temperature.
DS70592B-page 296
Preliminary
 2009 Microchip Technology Inc.
PIC24HJXXXGPX06A/X08A/X10A
INDEX
A
AC Characteristics .................................................... 248, 278
ADC Module.............................................................. 281
ADC Module (10-bit Mode) ....................................... 282
ADC Module (12-bit Mode) ....................................... 281
Internal RC Accuracy ................................................ 250
Load Conditions ................................................ 248, 278
ADC Module
ADC1 Register Map .................................................... 44
ADC2 Register Map .................................................... 44
Alternate Interrupt Vector Table (AIVT) .............................. 73
Analog-to-Digital Converter............................................... 207
DMA .......................................................................... 207
Initialization ............................................................... 207
Key Features............................................................. 207
Arithmetic Logic Unit (ALU)................................................. 30
Assembler
MPASM Assembler................................................... 236
Automatic Clock Stretch.................................................... 168
B
Block Diagrams
16-bit Timer1 Module ................................................ 147
ADC1 Module............................................................ 208
Connections for On-Chip Voltage Regulator............. 224
ECAN Module ........................................................... 182
Input Capture ............................................................ 155
Output Compare ....................................................... 157
PIC24H ....................................................................... 18
PIC24H CPU Core ...................................................... 26
PIC24H Oscillator System Diagram.......................... 127
PIC24H PLL .............................................................. 129
Reset System.............................................................. 67
Shared Port Structure ............................................... 145
SPI ............................................................................ 161
Timer2 (16-bit) .......................................................... 151
Timer2/3 (32-bit) ....................................................... 150
UART ........................................................................ 175
Watchdog Timer (WDT) ............................................ 225
C
C Compilers
Hi-Tech C.................................................................. 236
MPLAB C .................................................................. 236
Clock Switching................................................................. 135
Enabling .................................................................... 135
Sequence.................................................................. 135
Code Examples
Erasing a Program Memory Page............................... 64
Initiating a Programming Sequence............................ 65
Loading Write Buffers ................................................. 65
Port Write/Read ........................................................ 146
PWRSAV Instruction Syntax..................................... 137
Code Protection ........................................................ 219, 226
Configuration Bits.............................................................. 219
Description (Table).................................................... 220
Configuration Register Map .............................................. 219
Configuring Analog Port Pins ............................................ 146
CPU
Control Register .......................................................... 27
CPU Clocking System....................................................... 128
PLL Configuration ..................................................... 128
Selection ................................................................... 128
Sources..................................................................... 128
 2009 Microchip Technology Inc.
Customer Change Notification Service............................. 301
Customer Support............................................................. 301
D
Data Address Space........................................................... 33
Alignment.................................................................... 33
Memory Map for PIC24HJXXXGPX06A/X08A/X10A Devices with 16 KB RAM ........................................ 35
Memory Map for PIC24HJXXXGPX06A/X08A/X10A Devices with 8 KB RAM .......................................... 34
Near Data Space ........................................................ 33
Software Stack ........................................................... 55
Width .......................................................................... 33
DC Characteristics............................................................ 240
Doze Current (IDOZE)................................................ 277
High Temperature..................................................... 276
I/O Pin Input Specifications ...................................... 245
I/O Pin Output........................................................... 277
I/O Pin Output Specifications.................................... 246
Idle Current (IDOZE) .................................................. 244
Idle Current (IIDLE) .................................................... 243
Operating Current (IDD) ............................................ 242
Operating MIPS vs. Voltage ..................................... 276
Power-Down Current (IPD)........................................ 244
Power-down Current (IPD) ........................................ 276
Program Memory.............................................. 247, 277
Temperature and Voltage......................................... 276
Temperature and Voltage Specifications.................. 241
Thermal Operating Conditions.................................. 276
Demonstration/Development Boards, Evaluation Kits, and
Starter Kits................................................................ 238
Development Support ....................................................... 235
DMA Module
DMA Register Map ..................................................... 45
DMAC Registers ............................................................... 118
DMAxCNT ................................................................ 118
DMAxCON................................................................ 118
DMAxPAD ................................................................ 118
DMAxREQ ................................................................ 118
DMAxSTA ................................................................. 118
DMAxSTB ................................................................. 118
E
ECAN Module
CiFMSKSEL2 register .............................................. 199
ECAN1 Register Map (C1CTRL1.WIN = 0 or 1)......... 46
ECAN1 Register Map (C1CTRL1.WIN = 0)................ 47
ECAN1 Register Map (C1CTRL1.WIN = 1)................ 47
ECAN2 Register Map (C2CTRL1.WIN = 0 or 1)......... 49
ECAN2 Register Map (C2CTRL1.WIN = 0)................ 49
ECAN2 Register Map (C2CTRL1.WIN = 1)................ 50
Frame Types ............................................................ 181
Modes of Operation .................................................. 183
Overview................................................................... 181
ECAN Registers
Filter 15-8 Mask Selection Register (CiFMSKSEL2) 199
Electrical Characteristics .................................................. 239
AC..................................................................... 248, 278
Enhanced CAN Module .................................................... 181
Equations
Device Operating Frequency.................................... 128
FOSC Calculation..................................................... 128
XT with PLL Mode Example ..................................... 129
Errata .................................................................................. 16
Preliminary
DS70592B-page 297
PIC24HJXXXGPX06A/X08A/X10A
F
M
Flash Program Memory....................................................... 61
Control Registers ........................................................ 62
Operations .................................................................. 62
Programming Algorithm .............................................. 64
RTSP Operation.......................................................... 62
Table Instructions........................................................ 61
Flexible Configuration ....................................................... 219
FSCM
Delay for Crystal and PLL Clock Sources ................... 71
Device Resets ............................................................. 71
Memory Organization ......................................................... 31
Microchip Internet Web Site.............................................. 301
Modes of Operation
Disable...................................................................... 183
Initialization ............................................................... 183
Listen All Messages.................................................. 183
Listen Only................................................................ 183
Loopback .................................................................. 183
Normal Operation ..................................................... 183
MPLAB ASM30 Assembler, Linker, Librarian ................... 236
MPLAB ICD 3 In-Circuit Debugger System ...................... 237
MPLAB Integrated Development Environment Software.. 235
MPLAB PM3 Device Programmer .................................... 238
MPLAB REAL ICE In-Circuit Emulator System ................ 237
MPLINK Object Linker/MPLIB Object Librarian ................ 236
Multi-Bit Data Shifter........................................................... 30
H
High Temperature Electrical Characteristics..................... 275
I
I/O Ports ............................................................................ 145
Parallel I/O (PIO)....................................................... 145
Write/Read Timing .................................................... 146
I2C
Operating Modes ...................................................... 167
Registers ................................................................... 167
I2C Module
I2C1 Register Map ...................................................... 42
I2C2 Register Map ...................................................... 42
In-Circuit Debugger ........................................................... 226
In-Circuit Emulation........................................................... 219
In-Circuit Serial Programming (ICSP) ....................... 219, 226
Input Capture
Registers ................................................................... 156
Input Change Notification Module ..................................... 146
Instruction Addressing Modes............................................. 55
File Register Instructions ............................................ 55
Fundamental Modes Supported.................................. 56
MCU Instructions ........................................................ 55
Move and Accumulator Instructions ............................ 56
Other Instructions........................................................ 56
Instruction Set
Overview ................................................................... 229
Summary................................................................... 227
Instruction-Based Power-Saving Modes ........................... 137
Idle ............................................................................ 138
Sleep ......................................................................... 137
Internal RC Oscillator
Use with WDT ........................................................... 225
Internet Address................................................................ 301
Interrupt Control and Status Registers................................ 77
IECx ............................................................................ 77
IFSx............................................................................. 77
INTCON1 .................................................................... 77
INTCON2 .................................................................... 77
INTTREG .................................................................... 77
IPCx ............................................................................ 77
Interrupt Setup Procedures ............................................... 116
Initialization ............................................................... 116
Interrupt Disable........................................................ 116
Interrupt Service Routine .......................................... 116
Trap Service Routine ................................................ 116
Interrupt Vector Table (IVT) ................................................ 73
Interrupts Coincident with Power Save Instructions.......... 138
J
JTAG Boundary Scan Interface ........................................ 219
DS70592B-page 298
N
NVM Module
Register Map .............................................................. 54
O
Open-Drain Configuration................................................. 146
Output Compare ............................................................... 157
P
Packaging ......................................................................... 285
Details....................................................................... 288
Marking ..................................................................... 285
Peripheral Module Disable (PMD) .................................... 138
PICkit 2 Development Programmer/Debugger and PICkit 2
Debug Express ......................................................... 238
PICkit 3 In-Circuit Debugger/Programmer and PICkit 3 Debug
Express..................................................................... 237
Pinout I/O Descriptions (table)............................................ 19
PMD Module
Register Map .............................................................. 54
POR and Long Oscillator Start-up Times ........................... 71
PORTA
Register Map .............................................................. 52
PORTB
Register Map .............................................................. 52
PORTC
Register Map .............................................................. 52
PORTD
Register Map .............................................................. 52
PORTE
Register Map .............................................................. 53
PORTF
Register Map .............................................................. 53
PORTG
Register Map .............................................................. 53
Power-Saving Features .................................................... 137
Clock Frequency and Switching ............................... 137
Program Address Space..................................................... 31
Construction ............................................................... 57
Data Access from Program Memory Using Program
Space Visibility ................................................... 60
Data Access from Program Memory Using Table Instructions .................................................................... 59
Data Access from, Address Generation ..................... 58
Memory Map............................................................... 31
Table Read Instructions
TBLRDH ............................................................. 59
TBLRDL.............................................................. 59
Visibility Operation ...................................................... 60
Preliminary
 2009 Microchip Technology Inc.
PIC24HJXXXGPX06A/X08A/X10A
Program Memory
Interrupt Vector ........................................................... 32
Organization................................................................ 32
Reset Vector ............................................................... 32
R
Reader Response ............................................................. 302
Registers
ADxCHS0 (ADCx Input Channel 0 Select................. 216
ADxCHS123 (ADCx Input Channel 1, 2, 3 Select) ... 215
ADxCON1 (ADCx Control 1)..................................... 210
ADxCON2 (ADCx Control 2)..................................... 212
ADxCON3 (ADCx Control 3)..................................... 213
ADxCON4 (ADCx Control 4)..................................... 214
ADxCSSH (ADCx Input Scan Select High)............... 217
ADxCSSL (ADCx Input Scan Select Low) ................ 217
ADxPCFGH (ADCx Port Configuration High) ........... 218
ADxPCFGL (ADCx Port Configuration Low)............. 218
CiBUFPNT1 (ECAN Filter 0-3 Buffer Pointer)........... 194
CiBUFPNT2 (ECAN Filter 4-7 Buffer Pointer)........... 195
CiBUFPNT3 (ECAN Filter 8-11 Buffer Pointer)......... 195
CiBUFPNT4 (ECAN Filter 12-15 Buffer Pointer)....... 196
CiCFG1 (ECAN Baud Rate Configuration 1) ............ 192
CiCFG2 (ECAN Baud Rate Configuration 2) ............ 193
CiCTRL1 (ECAN Control 1) ...................................... 184
CiCTRL2 (ECAN Control 2) ...................................... 185
CiEC (ECAN Transmit/Receive Error Count)............ 191
CiFCTRL (ECAN FIFO Control)................................ 187
CiFEN1 (ECAN Acceptance Filter Enable) ............... 194
CiFIFO (ECAN FIFO Status)..................................... 188
CiFMSKSEL1 (ECAN Filter 7-0 Mask Selection)..... 198,
199
CiINTE (ECAN Interrupt Enable) .............................. 190
CiINTF (ECAN Interrupt Flag)................................... 189
CiRXFnEID (ECAN Acceptance Filter n Extended Identifier).................................................................... 197
CiRXFnSID (ECAN Acceptance Filter n Standard Identifier).................................................................... 197
CiRXFUL1 (ECAN Receive Buffer Full 1) ................. 201
CiRXFUL2 (ECAN Receive Buffer Full 2) ................. 201
CiRXMnEID (ECAN Acceptance Filter Mask n Extended
Identifier) ........................................................... 200
CiRXMnSID (ECAN Acceptance Filter Mask n Standard
Identifier) ........................................................... 200
CiRXOVF1 (ECAN Receive Buffer Overflow 1) ........ 202
CiRXOVF2 (ECAN Receive Buffer Overflow 2) ........ 202
CiTRBnDLC (ECAN Buffer n Data Length Control) .. 205
CiTRBnEID (ECAN Buffer n Extended Identifier) ..... 204
CiTRBnSID (ECAN Buffer n Standard Identifier) ...... 204
CiTRBnSTAT (ECAN Receive Buffer n Status) ........ 206
CiTRmnCON (ECAN TX/RX Buffer m Control)......... 203
CiVEC (ECAN Interrupt Code).................................. 186
CLKDIV (Clock Divisor)............................................. 132
CORCON (Core Control) ...................................... 29, 78
DMACS0 (DMA Controller Status 0)......................... 123
DMACS1 (DMA Controller Status 1)......................... 125
DMAxCNT (DMA Channel x Transfer Count) ........... 122
DMAxCON (DMA Channel x Control) ....................... 119
DMAxPAD (DMA Channel x Peripheral Address)..... 122
DMAxREQ (DMA Channel x IRQ Select) ................. 120
DMAxSTA (DMA Channel x RAM Start Address A) . 121
DMAxSTB (DMA Channel x RAM Start Address B) . 121
DSADR (Most Recent DMA RAM Address).............. 126
I2CxCON (I2Cx Control) ........................................... 169
I2CxMSK (I2Cx Slave Mode Address Mask) ............ 173
I2CxSTAT (I2Cx Status) ........................................... 171
 2009 Microchip Technology Inc.
ICxCON (Input Capture x Control)............................ 156
IEC0 (Interrupt Enable Control 0) ............................... 89
IEC1 (Interrupt Enable Control 1) ............................... 91
IEC2 (Interrupt Enable Control 2) ............................... 93
IEC3 (Interrupt Enable Control 3) ............................... 95
IEC4 (Interrupt Enable Control 4) ............................... 96
IFS0 (Interrupt Flag Status 0) ..................................... 81
IFS1 (Interrupt Flag Status 1) ..................................... 83
IFS2 (Interrupt Flag Status 2) ..................................... 85
IFS3 (Interrupt Flag Status 3) ..................................... 87
IFS4 (Interrupt Flag Status 4) ..................................... 88
INTCON1 (Interrupt Control 1) ................................... 79
INTCON2 (Interrupt Control 2) ................................... 80
IPC0 (Interrupt Priority Control 0) ............................... 97
IPC1 (Interrupt Priority Control 1) ............................... 98
IPC10 (Interrupt Priority Control 10) ......................... 107
IPC11 (Interrupt Priority Control 11) ......................... 108
IPC12 (Interrupt Priority Control 12) ......................... 109
IPC13 (Interrupt Priority Control 13) ......................... 110
IPC14 (Interrupt Priority Control 14) ......................... 111
IPC15 (Interrupt Priority Control 15) ......................... 112
IPC16 (Interrupt Priority Control 16) ................. 113, 115
IPC17 (Interrupt Priority Control 17) ......................... 114
IPC2 (Interrupt Priority Control 2) ............................... 99
IPC3 (Interrupt Priority Control 3) ............................. 100
IPC4 (Interrupt Priority Control 4) ............................. 101
IPC5 (Interrupt Priority Control 5) ............................. 102
IPC6 (Interrupt Priority Control 6) ............................. 103
IPC7 (Interrupt Priority Control 7) ............................. 104
IPC8 (Interrupt Priority Control 8) ............................. 105
IPC9 (Interrupt Priority Control 9) ............................. 106
NVMCON (Flash Memory Control)............................. 63
OCxCON (Output Compare x Control) ..................... 159
OSCCON (Oscillator Control)................................... 130
OSCTUN (FRC Oscillator Tuning)............................ 134
PLLFBD (PLL Feedback Divisor) ............................. 133
PMD1 (Peripheral Module Disable Control Register 1) ..
139
PMD2 (Peripheral Module Disable Control Register 2) ..
141
PMD3 (Peripheral Module Disable Control Register 3) ..
143
RCON (Reset Control)................................................ 68
SPIxCON1 (SPIx Control 1) ..................................... 163
SPIxCON2 (SPIx Control 2) ..................................... 165
SPIxSTAT (SPIx Status and Control) ....................... 162
SR (CPU Status) .................................................. 28, 78
T1CON (Timer1 Control) .......................................... 148
TxCON (T2CON, T4CON, T6CON or T8CON Control)..
152
TyCON (T3CON, T5CON, T7CON or T9CON Control)..
153
UxMODE (UARTx Mode) ......................................... 176
UxSTA (UARTx Status and Control) ........................ 178
Reset
Clock Source Selection .............................................. 70
Special Function Register Reset States ..................... 71
Times.......................................................................... 70
Reset Sequence ................................................................. 73
Resets ................................................................................ 67
Preliminary
DS70592B-page 299
PIC24HJXXXGPX06A/X08A/X10A
S
Serial Peripheral Interface (SPI) ....................................... 161
Software Simulator (MPLAB SIM)..................................... 237
Software Stack Pointer, Frame Pointer
CALL Stack Frame...................................................... 55
Special Features ............................................................... 219
SPI Module
SPI1 Register Map ...................................................... 43
SPI2 Register Map ...................................................... 43
Symbols Used in Opcode Descriptions............................. 228
System Control
Register Map............................................................... 54
T
Temperature and Voltage Specifications
AC ..................................................................... 248, 278
Timer1 ............................................................................... 147
Timer2/3, Timer4/5, Timer6/7 and Timer8/9 ..................... 149
Timing Characteristics
CLKO and I/O ........................................................... 251
Timing Diagrams
10-bit Analog-to-Digital Conversion (CHPS<1:0> = 01,
SIMSAM = 0, ASAM = 1, SSRC<2:0> = 111,
SAMC<4:0> = 00001) ....................................... 273
10-bit Analog-to-Digtial Conversion (CHPS<1:0> = 01,
SIMSAM = 0, ASAM = 0, SSRC<2:0> = 000) ... 273
12-bit Analog-to-Digital Conversion (ASAM = 0, SSRC<2:0> = 000) ................................................ 271
ECAN I/O .................................................................. 267
External Clock ........................................................... 249
I2Cx Bus Data (Master Mode) .................................. 263
I2Cx Bus Data (Slave Mode) .................................... 265
I2Cx Bus Start/Stop Bits (Master Mode) ................... 263
I2Cx Bus Start/Stop Bits (Slave Mode) ..................... 265
Input Capture (CAPx)................................................ 256
OC/PWM ................................................................... 257
Output Compare (OCx) ............................................. 256
Reset, Watchdog Timer, Oscillator Start-up Timer and
Power-up Timer ................................................ 252
SPIx Master Mode (CKE = 0).................................... 258
SPIx Master Mode (CKE = 1).................................... 259
SPIx Slave Mode (CKE = 0)...................................... 260
SPIx Slave Mode (CKE = 1)...................................... 261
DS70592B-page 300
Timer1, 2 and 3 External Clock ................................ 254
Timing Requirements
ADC Conversion (10-bit mode)................................. 283
ADC Conversion (12-bit Mode)................................. 283
CLKO and I/O ........................................................... 251
External Clock........................................................... 249
Input Capture ............................................................ 256
SPIx Master Mode (CKE = 0) ................................... 279
SPIx Module Master Mode (CKE = 1) ...................... 279
SPIx Module Slave Mode (CKE = 0) ........................ 280
SPIx Module Slave Mode (CKE = 1) ........................ 280
Timing Specifications
10-bit Analog-to-Digital Conversion Requirements... 274
CAN I/O Requirements ............................................. 267
I2Cx Bus Data Requirements (Master Mode)........... 264
I2Cx Bus Data Requirements (Slave Mode)............. 266
Output Compare Requirements................................ 256
PLL Clock ......................................................... 250, 278
Reset, Watchdog Timer, Oscillator Start-up Timer, Power-up Timer and Brown-out Reset Requirements ...
253
Simple OC/PWM Mode Requirements ..................... 257
SPIx Master Mode (CKE = 0) Requirements............ 258
SPIx Master Mode (CKE = 1) Requirements............ 259
SPIx Slave Mode (CKE = 0) Requirements.............. 260
SPIx Slave Mode (CKE = 1) Requirements.............. 262
Timer1 External Clock Requirements ....................... 254
Timer2 External Clock Requirements ....................... 255
Timer3 External Clock Requirements ....................... 255
U
UART Module
UART1 Register Map.................................................. 42
UART2 Register Map.................................................. 43
V
Voltage Regulator (On-Chip) ............................................ 224
W
Watchdog Timer (WDT)............................................ 219, 225
Programming Considerations ................................... 225
WWW Address ................................................................. 301
WWW, On-Line Support ..................................................... 16
Preliminary
 2009 Microchip Technology Inc.
PIC24HJXXXGPX06A/X08A/X10A
THE MICROCHIP WEB SITE
CUSTOMER SUPPORT
Microchip provides online support via our WWW site at
www.microchip.com. This web site is used as a means
to make files and information easily available to
customers. Accessible by using your favorite Internet
browser, the web site contains the following information:
Users of Microchip products can receive assistance
through several channels:
• Product Support – Data sheets and errata, application notes and sample programs, design
resources, user’s guides and hardware support
documents, latest software releases and archived
software
• General Technical Support – Frequently Asked
Questions (FAQs), technical support requests,
online discussion groups, Microchip consultant
program member listing
• Business of Microchip – Product selector and
ordering guides, latest Microchip press releases,
listing of seminars and events, listings of Microchip sales offices, distributors and factory representatives
•
•
•
•
Distributor or Representative
Local Sales Office
Field Application Engineer (FAE)
Technical Support
Customers should contact their distributor, representative or field application engineer (FAE) for support.
Local sales offices are also available to help customers. A listing of sales offices and locations is included in
the back of this document.
Technical support is available through the web site
at: http://support.microchip.com
CUSTOMER CHANGE NOTIFICATION
SERVICE
Microchip’s customer notification service helps keep
customers current on Microchip products. Subscribers
will receive e-mail notification whenever there are
changes, updates, revisions or errata related to a specified product family or development tool of interest.
To register, access the Microchip web site at
www.microchip.com, click on Customer Change Notification and follow the registration instructions.
 2009 Microchip Technology Inc.
Preliminary
DS70592B-page 301
PIC24HJXXXGPX06A/X08A/X10A
READER RESPONSE
It is our intention to provide you with the best documentation possible to ensure successful use of your Microchip product. If you wish to provide your comments on organization, clarity, subject matter, and ways in which our documentation
can better serve you, please FAX your comments to the Technical Publications Manager at (480) 792-4150.
Please list the following information, and use this outline to provide us with your comments about this document.
To:
Technical Publications Manager
RE:
Reader Response
Total Pages Sent ________
From: Name
Company
Address
City / State / ZIP / Country
Telephone: (_______) _________ - _________
FAX: (______) _________ - _________
Application (optional):
Would you like a reply?
Y
N
Device: PIC24HJXXXGPX06A/X08A/X10A
Literature Number: DS70592B
Questions:
1. What are the best features of this document?
2. How does this document meet your hardware and software development needs?
3. Do you find the organization of this document easy to follow? If not, why?
4. What additions to the document do you think would enhance the structure and subject?
5. What deletions from the document could be made without affecting the overall usefulness?
6. Is there any incorrect or misleading information (what and where)?
7. How would you improve this document?
DS70592B-page 302
Preliminary
 2009 Microchip Technology Inc.
PIC24HJXXXGPX06A/X08A/X10A
PRODUCT IDENTIFICATION SYSTEM
To order or obtain information, e.g., on pricing or delivery, refer to the factory or the listed sales office.
PIC 24 HJ 256 GP6 10 A T I/PT - XXX
Examples:
a)
Microchip Trademark
Architecture
Flash Memory Family
b)
Program Memory Size (KB)
Product Group
PIC24HJ256GP210AI/PT:
General-purpose PIC24H, 256 KB program
memory, 100-pin, Industrial temp.,
TQFP package.
PIC24HJ64GP506AI/PT-ES:
General-purpose PIC24H, 64 KB program
memory, 64-pin, Industrial temp.,
TQFP package, Engineering Sample.
Pin Count
Revision Level
Tape and Reel Flag (if applicable)
Temperature Range
Package
Pattern
Architecture:
24
=
16-bit Microcontroller
Flash Memory Family: HJ
=
Flash program memory, 3.3V, High-speed
Product Group:
GP2
GP3
GP5
GP6
=
=
=
=
General purpose family
General purpose family
General purpose family
General purpose family
Pin Count:
06
10
=
=
64-pin
100-pin
Temperature Range:
I
E
H
=
=
=
-40C to+85C(Industrial)
-40C to+125C(Extended)
-40C to+140C(High)
Package:
PT
PF
MR
=
=
=
10x10 or 12x12 mm TQFP (Thin Quad Flatpack)
14x14 mm TQFP (Thin Quad Flatpack)
9x9x0.9 mm QFN (Thin Quad Flatpack)
Pattern:
Three-digit QTP, SQTP, Code or Special Requirements
(blank otherwise)
ES
= Engineering Sample
 2009 Microchip Technology Inc.
Preliminary
DS70592B-page 303
WORLDWIDE SALES AND SERVICE
AMERICAS
ASIA/PACIFIC
ASIA/PACIFIC
EUROPE
Corporate Office
2355 West Chandler Blvd.
Chandler, AZ 85224-6199
Tel: 480-792-7200
Fax: 480-792-7277
Technical Support:
http://support.microchip.com
Web Address:
www.microchip.com
Asia Pacific Office
Suites 3707-14, 37th Floor
Tower 6, The Gateway
Harbour City, Kowloon
Hong Kong
Tel: 852-2401-1200
Fax: 852-2401-3431
India - Bangalore
Tel: 91-80-3090-4444
Fax: 91-80-3090-4080
India - New Delhi
Tel: 91-11-4160-8631
Fax: 91-11-4160-8632
Austria - Wels
Tel: 43-7242-2244-39
Fax: 43-7242-2244-393
Denmark - Copenhagen
Tel: 45-4450-2828
Fax: 45-4485-2829
India - Pune
Tel: 91-20-2566-1512
Fax: 91-20-2566-1513
France - Paris
Tel: 33-1-69-53-63-20
Fax: 33-1-69-30-90-79
Japan - Yokohama
Tel: 81-45-471- 6166
Fax: 81-45-471-6122
Germany - Munich
Tel: 49-89-627-144-0
Fax: 49-89-627-144-44
Atlanta
Duluth, GA
Tel: 678-957-9614
Fax: 678-957-1455
Boston
Westborough, MA
Tel: 774-760-0087
Fax: 774-760-0088
Chicago
Itasca, IL
Tel: 630-285-0071
Fax: 630-285-0075
Cleveland
Independence, OH
Tel: 216-447-0464
Fax: 216-447-0643
Dallas
Addison, TX
Tel: 972-818-7423
Fax: 972-818-2924
Detroit
Farmington Hills, MI
Tel: 248-538-2250
Fax: 248-538-2260
Kokomo
Kokomo, IN
Tel: 765-864-8360
Fax: 765-864-8387
Los Angeles
Mission Viejo, CA
Tel: 949-462-9523
Fax: 949-462-9608
Santa Clara
Santa Clara, CA
Tel: 408-961-6444
Fax: 408-961-6445
Toronto
Mississauga, Ontario,
Canada
Tel: 905-673-0699
Fax: 905-673-6509
Australia - Sydney
Tel: 61-2-9868-6733
Fax: 61-2-9868-6755
China - Beijing
Tel: 86-10-8528-2100
Fax: 86-10-8528-2104
Korea - Daegu
Tel: 82-53-744-4301
Fax: 82-53-744-4302
China - Chengdu
Tel: 86-28-8665-5511
Fax: 86-28-8665-7889
China - Hong Kong SAR
Tel: 852-2401-1200
Fax: 852-2401-3431
Korea - Seoul
Tel: 82-2-554-7200
Fax: 82-2-558-5932 or
82-2-558-5934
China - Nanjing
Tel: 86-25-8473-2460
Fax: 86-25-8473-2470
Malaysia - Kuala Lumpur
Tel: 60-3-6201-9857
Fax: 60-3-6201-9859
China - Qingdao
Tel: 86-532-8502-7355
Fax: 86-532-8502-7205
Malaysia - Penang
Tel: 60-4-227-8870
Fax: 60-4-227-4068
China - Shanghai
Tel: 86-21-5407-5533
Fax: 86-21-5407-5066
Philippines - Manila
Tel: 63-2-634-9065
Fax: 63-2-634-9069
China - Shenyang
Tel: 86-24-2334-2829
Fax: 86-24-2334-2393
Singapore
Tel: 65-6334-8870
Fax: 65-6334-8850
China - Shenzhen
Tel: 86-755-8203-2660
Fax: 86-755-8203-1760
Taiwan - Hsin Chu
Tel: 886-3-6578-300
Fax: 886-3-6578-370
China - Wuhan
Tel: 86-27-5980-5300
Fax: 86-27-5980-5118
Taiwan - Kaohsiung
Tel: 886-7-536-4818
Fax: 886-7-536-4803
China - Xiamen
Tel: 86-592-2388138
Fax: 86-592-2388130
Taiwan - Taipei
Tel: 886-2-2500-6610
Fax: 886-2-2508-0102
China - Xian
Tel: 86-29-8833-7252
Fax: 86-29-8833-7256
Thailand - Bangkok
Tel: 66-2-694-1351
Fax: 66-2-694-1350
Italy - Milan
Tel: 39-0331-742611
Fax: 39-0331-466781
Netherlands - Drunen
Tel: 31-416-690399
Fax: 31-416-690340
Spain - Madrid
Tel: 34-91-708-08-90
Fax: 34-91-708-08-91
UK - Wokingham
Tel: 44-118-921-5869
Fax: 44-118-921-5820
China - Zhuhai
Tel: 86-756-3210040
Fax: 86-756-3210049
03/26/09
DS70592B-page 304
Preliminary
 2009 Microchip Technology Inc.