1008 POWER INDUCTORS Power Inductor for Critical Applications ST413PHA ■ Shielded power inductors ■ Excellent current handling for a part this size; low DCR Core material Ceramic/Ferrite Terminations Silver-palladium-platinum-glass frit. Other terminations available at additional cost. Weight 122 – 132 mg Ambient temperature –40°C to +105°C with Irms current, +105°C to +145°C with derated current Storage temperature Component: –55°C to +105°C. Packaging: –55°C to +80°C Resistance to soldering heat Max three 40 second reflows at +260°C, parts cooled to room temperature between cycles Temperature Coefficient of Inductance (TCL) +100 to +350 ppm/°C Moisture Sensitivity Level (MSL) 1 (unlimited floor life at <30°C / 85% relative humidity) Packaging 750/7²reel; 2500/13² reel Plastic tape: 12 mm wide, 0.3 mm thick, 8 mm pocket spacing, 3.3 mm pocket depth 7 Isat (A)6 Inductance DCR4 SRF5 Irms (A) ±10%2 Q max typ 10% 20% 30% 20°C 40°C Part number1 (µH) min3(Ohms)(MHz)dropdropdrop rise rise ST413PHA102KLZ 1.0 35 0.05387 3.53.94.21.4 2.0 ST413PHA152KLZ 1.5 35 0.06276 2.73.23.51.4 2.0 ST413PHA182KLZ 1.8 35 0.09253 2.32.73.00.981.4 ST413PHA222KLZ 2.2 36 0.10228 2.42.83.11.2 1.7 ST413PHA272KLZ 2.7 38 0.14207 1.62.02.31.0 1.4 ST413PHA332KLZ 3.3 26 0.84199 1.51.61.60.510.67 ST413PHA392KLZ 3.9 38 0.26185 1.51.82.00.821.1 ST413PHA472KLZ 4.7 38 0.35160 1.31.61.70.700.95 ST413PHA562KLZ 5.6 38 0.36150 1.51.71.80.660.87 ST413PHA682KLZ 6.8 38 0.58120 1.31.51.60.450.76 ST413PHA103KLZ 10 38 0.92 105 0.841.0 1.1 0.40 0.59 ST413PHA153KLZ 15 38 1.15 35 0.810.870.900.36 0.51 ST413PHA223KLZ 22 40 1.40 26 0.670.750.790.33 0.44 ST413PHA333KLZ 33 45 1.61 20 0.530.610.680.30 0.42 ST413PHA393KLZ 39 45 1.85 16 0.490.560.600.28 0.39 ST413PHA473KLZ 47 45 2.5 19 0.470.520.540.23 0.31 ST413PHA683KLZ 68 45 3.8 12 0.380.420.450.21 0.26 ST413PHA823KLZ 82 45 4.3 9.0 0.330.380.420.18 0.26 ST413PHA104KLZ 100 45 5.8 7.0 0.350.380.390.16 0.20 ST413PHA124KLZ 120 50 6.3 7.0 0.300.330.350.14 0.20 ST413PHA154KLZ 150 50 7.5 5.8 0.270.300.330.13 0.18 ST413PHA224KLZ 220 55 10.0 5.0 0.210.240.270.13 0.17 ST413PHA334KLZ 330 55 11.5 3.8 0.190.210.230.11 0.15 ST413PHA474KLZ 470 55 16.3 3.1 0.140.170.190.10 0.13 ST413PHA564KLZ 560 55 18.1 2.8 0.130.150.170.0930.12 ST413PHA684KLZ 680 55 24.0 2.5 0.110.150.170.0730.11 ST413PHA824KLZ 820 45 26.0 1.5 0.100.120.130.0730.10 ST413PHA105KLZ 1000 45 29.0 2.0 0.110.130.140.0700.10 ® ST413PHA334KLZ Termination:L =RoHS compliant silver-palladiumplatinum-glass frit. Special order: T = RoHS tin-silver-copper (95.5/4/0.5) or S = non-RoHS tinlead (63/37). Testing:Z= COTS H=Screening per Coilcraft CPSA-10001 2. Inductance measured at 100 kHz, 0.1 Vrms, using Coilcraft SMD-A fixture in Agilent/HP 4263B impedance analyzer or equivalent. 3. Q measured at 1 MHz using an Agilent/HP 16193 test fixture and an Agilent/HP 4291 or equivalent. 4. DCR measured on micro-ohmmeter and Coilcraft CCF840 test fixture. 5. SRF measured using a Coilcraft SMD‑D test fixture and an Agilent/HP 8753D network analyzer or equivalent. 6. DC current at which the inductance drops the specicfied amount from its value without current. 7. Current that causes the specified temperature rise from 25°C ambient. 8. Electrical specifications at 25°C. Refer to Doc 362 “Soldering Surface Mount Components” before soldering. Specifications subject to change without notice. Please check our website for latest information. 1102 Silver Lake Road Cary IL 60013 © Coilcraft, Inc. 2011 1. When ordering, specify termination and testing codes: Document ST219-1 Revised 03/08/11 Phone 800-981-0363 Fax 847-639-1508 E-mail [email protected] Web www.coilcraft-cps.com 1008 POWER INDUCTORS Power Inductor for Critical Applications ST413PHA Typical L vs Frequency Typical L vs Current 10000 10000 1000 µH 100 µH 100 10 µH 10 0.01 100 µH 100 1 µH 1 0.1 1000 µH 1000 Inductance (µH) Inductance (µH) 1000 10 µH 10 1 µH 1 1 0.1 0.1 10 0.01 1 0.1 Irms Derating B F C D 120 H I 110 A 100 J E 90 G I 80 Terminal wraparound: approx 0.015/0,38 both ends 70 60 Suggested Recommended Land Pattern ABCDEFG max maxmaxmaxmaxmaxtyp H IJ 0.1500.1490.1080.0700.1020.0840.0200.1000.0400.050 inches 3,813,782,741,782,592,130,512,541,021,27mm 50 40 25°C Percent of rated Irms 10 Current (A) Frequency (MHz) 30 Note: Height dimension is before optional solder application. For maximum height including solder, add 0.006 in / 0,15 mm. 20 10 0 -40 -20 0 20 40 60 80 100 120 140 160 Ambient temperature (°C) ® Specifications subject to change without notice. Please check our website for latest information. 1102 Silver Lake Road Cary IL 60013 © Coilcraft, Inc. 2011 Document ST219-2 Revised 03/08/11 Phone 800-981-0363 Fax 847-639-1508 E-mail [email protected] Web www.coilcraft-cps.com