Electrical Specifications Subject to Change LTC3330 Energy Harvesting DC/DC with Battery Backup Features Description Dual Input, Single Output DC/DC’s with Input Prioritizer Energy Harvesting Input: 3.0V to 18V Buck DC/DC Primary Cell Input: 1.8V to 5.5V Buck-Boost DC/DC n Zero Battery I When Powering Load from Q Harvested Energy n Ultralow Quiescent Current: 900nA at No-Load n Low Noise LDO Post Regulator n Integrated Supercapacitor Balancer n Up to 50mA of Output Current n Programmable DC/DC and LDO Output Voltages, Buck UVLO, and Buck-Boost Peak Input Current n Integrated Low Loss Full-Wave Bridge Rectifier n Input Protective Shunt–Up to 25mA at V ≥ 20V IN n5mm × 5mm QFN-32 Package The LTC®3330 integrates a high voltage energy harvesting power supply plus a DC/DC converter powered by a primary cell battery to create a single output supply for alternative energy applications. The energy harvesting power supply, consisting of an integrated full-wave bridge rectifier and a high voltage buck converter, harvests energy from piezoelectric, solar, or magnetic sources. The primary cell input powers a buck-boost converter capable of operation down to 1.8V at its input. Either DC/DC converter can deliver energy to a single output. The buck operates when harvested energy is available, reducing the quiescent current draw on the battery to essentially zero. The buck-boost takes over when harvested energy goes away. n Applications n n n n A low noise LDO post regulator and a supercapacitor balancer are also integrated, accommodating a wide range of output storage configurations. Voltage and current settings for both inputs and outputs are programmable via pin-strapped logic inputs. Energy Harvesting Solar Powered Systems with Primary Cell Backup Wireless HVAC Sensors and Security Devices Mobile Asset Tracking The LTC3330 is available in a 5mm × 5mm QFN-32 package. L, LT, LTC, LTM, Linear Technology and the Linear logo are registered trademarks of Linear Technology Corporation. All other trademarks are the property of their respective owners. Typical Application 4V TO 18V + 3V TO 18V SOLAR PANEL – AC1 AC2 VIN SW 1µF 6V 10µF 25V 4.7µF, 6V LTC3330 SWA CAP SWB VIN2 VOUT PIEZO MIDE V25W 22µH 22µH 1.2V TO 5V 50mA LDO_IN + PRIMARY CELL 1.8V TO 5.5V 1µF 6V 10mF 2.5V SCAP BAT BAL 3 3 3 4 10mF 2.5V LDO_EN OUT[2:0] 22µF 6V EH_ON LDO[2:0] OPTIONAL PGVOUT IPK[2:0] PGLDO UV[3:0] 1.2V TO 3.6V 50mA LDO_OUT GND VIN3 1µF 6V 2.2µF 6V 3330 TA01a 3330p For more information www.linear.com/LTC3330 1 LTC3330 Absolute Maximum Ratings Pin Configuration (Note 1) LDO_EN VIN3 PGLDO PGVOUT EH_ON OUT0 OUT1 OUT2 TOP VIEW 32 31 30 29 28 27 26 25 BAL 1 24 LDO0 SCAP 2 23 LDO1 VIN2 3 22 LDO2 UV3 4 21 LDO_IN 33 GND UV2 5 20 LDO_OUT UV1 6 19 IPK2 UV0 7 18 IPK1 AC1 8 17 IPK0 BAT SWA SWB VOUT SW CAP VIN 9 10 11 12 13 14 15 16 AC2 VIN Low Impedance Source...........................–0.3 to 18V* Current-Fed, ISW = 0A.........................................25mA AC1, AC2..............................................................0 to VIN BAT, VOUT, VIN3, LDO_IN, SCAP, PGVOUT, PGLDO, EH_ON.........................................................–0.3 to 6V VIN2.....................–0.3V to [Lesser of (VIN + 0.3V) or 6V] CAP....................... [Higher of –0.3V or (VIN – 6V)] to VIN LDO_OUT, LDO[2:0], LDO_EN...–0.3V to LDO_IN + 0.3V BAL................................................–0.3V to SCAP + 0.3V OUT[2:0]........... –0.3V to [Lesser of (VIN3 + 0.3V) or 6V] IPK[2:0]............ –0.3V to [Lesser of (VIN3 + 0.3V) or 6V] UV[3:0]............. –0.3V to [Lesser of (VIN2 + 0.3V) or 6V] IAC1, IAC2...............................................................±50mA ISW, ISWA, ISWB, IVOUT...........................................350mA ILDO_OUT..................................................................50mA Operating Junction Temperature Range (Notes 2, 3)............................................. –40°C to 125°C Storage Temperature Range................... –65°C to 125°C UH PACKAGE 32-LEAD (5mm × 5mm) PLASTIC QFN TJMAX = 125°C, θJA = 34°C/W EXPOSED PAD (PIN 33) IS GND, MUST BE SOLDERED TO PCB *VIN has an internal 20V clamp Order Information LEAD FREE FINISH TAPE AND REEL PART MARKING PACKAGE DESCRIPTION TEMPERATURE RANGE LTC3330EUH#PBF LTC3330EUH#TRPBF 3330 32-Lead (5mm × 5mm) Plastic QFN –40°C to 85°C LTC3330IUH#PBF LTC3330IUH#TRPBF 3330 32-Lead (5mm × 5mm) Plastic QFN –40°C to 125°C Consult LTC Marketing for parts specified with wider operating temperature ranges. For more information on lead free part marking, go to: http://www.linear.com/leadfree/ For more information on tape and reel specifications, go to: http://www.linear.com/tapeandreel/ 3330p 2 For more information www.linear.com/LTC3330 LTC3330 Electrical Characteristics The l denotes the specifications which apply over the specified operating junction temperature range, otherwise specifications are at TA = 25°C (Note 2). VIN = 5V, BAT = 3.6V, SCAP = OV, LDO_IN = 0V unless otherwise specified. SYMBOL PARAMETER CONDITIONS MIN TYP MAX UNITS VIN Buck Input Voltage Range l 3.0 18 V VBAT Buck-Boost Input Voltage Range l 1.8 5.5 V IVIN VIN Quiescent Current VIN Input in UVLO Buck Enabled, Sleeping Buck Enabled, Sleeping Buck Enabled, Not Sleeping IBAT BAT Quiescent Current BAT Input with VIN Active Buck-Boost Enabled, Sleeping Buck-Boost Enabled, Not Sleeping VIN = 2.5V, BAT = 0V VIN = 4V, BAT = 0V VIN = 18V, BAT = 0V VIN = 5V, BAT = 0V, ISW1 = 0A (Note 4) 450 1150 1650 150 700 1800 2500 250 nA nA nA µA BAT = 1.8V, VIN = 5V BAT = 5V, VIN = 0V BAT = 5V, VIN = 0V, ISWA = ISWB = 0A (Note 4) 900 200 10 1500 330 nA nA µA VLDO_IN LDO_IN Input Range ILDO_IN LDO_IN Quiescent Current LDO_IN = 5.0V, ILDO_OUT = 0A 400 ILDO_OUT LDO_OUT Leakage Current LDO_IN = 5.0V, LDO_OUT = 5.0V 125 LDO_OUT Regulated LDO Output Voltage Error as a Percentage of Target LDO Line Regulation (1.8V to 5.5V) LDO_OUT = 1.2V, 10mA Load 2 mV/V LDO Load Regulation (10µA to 10mA) LDO_IN = 5.0V, LDO_OUT = 3.3V 2 mV/mA LDO Dropout Voltage LDO_OUT = 3.3V, 10mA LOAD 90 mV LDO Current Limit LDO_IN = 5.0V l l 1.8V 5.5V –2.0 600 nA nA 2.0 50 % mA IVOUT VOUT Leakage Current VOUT = 5.0V 125 ISCAP Supercapacitor Balancer Quiescent Current SCAP = 5.0V 165 ISOURCE Supercapacitor Balancer Source Current SCAP = 5.0V, BAL = 2.4V nA 250 10 nA mA ISINK Supercapacitor Balancer Sink Current SCAP = 5.0V, BAL = 2.6V VBAL Supercapacitor Balance Point Percentage of SCAP Voltage l 49 50 51 % VINUVLO VIN Undervoltage Lockout Thresholds (Rising or Falling) 3V Level l 2.85 3.00 3.15 V 4V Level l 3.80 4.00 4.20 V 5V Level l 4.75 5.00 5.25 V 6V Level l 5.70 6.00 6.30 V 7V Level l 6.65 7.00 7.35 V 8V Level l 7.60 8.00 8.40 V 9V Level l 8.55 9.00 9.45 V 10V Level l 9.50 10.0 10.5 V 11V Level l 10.4 11.0 11.6 V 12V Level l 11.4 12.0 12.6 V 13V Level l 12.3 13.0 13.7 V 14V Level l 13.3 14.0 14.7 V 15V Level l 14.2 15.0 15.8 V 16V Level l 15.2 16.0 16.8 V 17V Level l 16.1 17.0 17.9 V 18V Level l 17.1 18.0 18.9 V 19.0 20.0 21.0 V VSHUNT VIN Shunt Regulator Voltage IVIN = 1mA 10 mA 3330p For more information www.linear.com/LTC3330 3 LTC3330 Electrical Characteristics The l denotes the specifications which apply over the specified operating junction temperature range, otherwise specifications are at TA = 25°C (Note 2). VIN = 5V, BAT = 3.6V, SCAP = OV, LDO_IN = 0V unless otherwise specified. SYMBOL PARAMETER ISHUNT Maximum Protective Shunt Current CONDITIONS MIN Internal Bridge Rectifier Reverse Leakage Current VREVERSE = 18V Internal Bridge Rectifier Reverse Breakdown Voltage IREVERSE = 1µA Regulated Buck/Buck-Boost Output Voltage 1.8V Output Selected Sleep Threshold Wakeup Threshold 700 1400 IBUCK Available Buck Output Current Buck-Boost Peak Switch Current UNITS 800 1500 900 1600 mV mV 20 nA mA VSHUNT 30 l l TBD 1.806 1.794 TBD V V 2.5V Output Selected Sleep Threshold Wakeup Threshold l l TBD 2.508 2.492 TBD V V 2.8V Output Selected Sleep Threshold Wakeup Threshold l l TBD 2.809 2.791 TBD V V 3.0V Output Selected Sleep Threshold Wakeup Threshold l l TBD 3.010 2.990 TBD V V 3.3V Output Selected Sleep Threshold Wakeup Threshold l l TBD 3.311 3.289 TBD V V 3.6V Output Selected Sleep Threshold Wakeup Threshold l l TBD 3.612 3.588 TBD V V 4.5V Output Selected Sleep Threshold Wakeup Threshold l l TBD 4.515 4.485 TBD V V 5.0V Output Selected Sleep Threshold Wakeup Threshold l l TBD 5.017 4.983 TBD V V 200 250 350 mA 250mA Target Selected 250 350 mA 150mA Target Selected 150 TBD mA 100mA Target Selected 100 TBD mA 50mA Target Selected 50 TBD mA 25mA Target Selected 25 TBD mA 15mA Target Selected 15 TBD mA 10mA Target Selected 10 TBD mA 5 TBD IPEAK_BUCK Buck Peak Switch Current IIPEAK_BB MAX 25 Internal Bridge Rectifier Loss (|VAC1 – VAC2| – VIN) IBRIDGE = 10µA IBRIDGE = 50mA VOUT TYP l 100 5mA Target Selected IBB Available Buck-Boost Current IIPEAK_BB = 250mA, BAT = 1.8V, VOUT = 3.3V RP_BUCK Buck PMOS Switch On-Resistance RN_BUCK Buck NMOS Switch On-Resistance RP_BB Buck-Boost PMOS Switch On-Resistance Input and Output Switches RN_BB Buck-Boost NMOS Switch On-Resistance Input and Output Switches RP_LDO LDO PMOS Switch On-Resistance LDO_IN = 2.5V, ILDO_OUT = 50mA l V mA 50 mA mA 1.1 Ω 1.3 Ω 0.5 Ω 0.5 Ω 7 Ω 3330p 4 For more information www.linear.com/LTC3330 LTC3330 Electrical Characteristics The l denotes the specifications which apply over the specified operating junction temperature range, otherwise specifications are at TA = 25°C (Note 2). VIN = 5V, BAT = 3.6V, SCAP = OV, LDO_IN = 0V unless otherwise specified. SYMBOL PARAMETER CONDITIONS MIN ILEAK(P) PMOS Switch Leakage Buck/Buck-Boost Regulators –20 20 nA ILEAK(N) NMOS Switch Leakage Buck/Buck-Boost Regulators –20 20 nA Maximum Buck Duty Cycle Buck/Buck-Boost Regulators l 100 PGVOUT Threshold As a Percentage of VOUT Target l 90 92.5 95 % PGLDO Threshold As a Percentage of LDO_OUT Target l 90 92.5 95 % VIH Digital Input High Voltage Pins LDO_EN, OUT[2:0], LDO[2:0], IPK[2:0], UV[3:0] l 1.2 VIL Digital Input Low Voltage Pins LDO_EN, OUT[2:0], LDO[2:0], IPK[2:0], UV[3:0] l IIH Digital Input High Current Pins LDO_EN, OUT[2:0], LDO[2:0], IPK[2:0], UV[3:0] IIL Digital Input Low Current Pins LDO_EN, OUT[2:0], LDO[2:0], IPK[2:0], UV[3:0] VOH PGVOUT, PGLDO, EH_ON Output High Voltage VIN3 = 5V, 10µA Out of Pin l VOL PGVOUT, PGLDO, EH_ON Output Low Voltage VIN3 = 5V, 10µA into Pin l Note 1: Stresses beyond those listed under Absolute Maximum Ratings may cause permanent damage to the device. Exposure to any Absolute Maximum Rating condition for extended periods may affect device reliability and lifetime. Note 2: The LTC3330E is tested under pulsed load conditions such that TJ ≈ TA. The LTC3330E is guaranteed to meet specifications from 0°C to 85°C. The LTC3330I is guaranteed over the –40°C to 125°C operating junction temperature range. Note that the maximum ambient temperature TYP MAX UNITS % V 0.4 V 0 10 nA 0 10 nA 4.6 V 0.4 V consistent with these specifications is determined by specific operating conditions in conjunction with board layout, the rated package thermal impedance and other environmental factors. Note 3: TJ is calculated from the ambient TA and power dissipation PD according to the following formula: TJ = TA + (PD • θJA). Note 4: Dynamic supply current is higher due to gate charge being delivered at the switching frequency. 3330p For more information www.linear.com/LTC3330 5 LTC3330 Typical Performance Characteristics IVIN in UVLO vs VIN IVIN in Sleep vs VIN IBAT in Sleep vs BAT UVLO Rising vs Temperature UVLO Falling vs Temperature VSHUNT vs Temperature Total Bridge Rectifier Drop vs Bridge Current Bridge Leakage vs Temperature Bridge Frequency Response 3330p 6 For more information www.linear.com/LTC3330 LTC3330 Typical Performance Characteristics VOUT vs Temperature (1.8V, 2.5V, 2.8V, 3.0V) VOUT vs Temperature (3.3V, 3.6V, 4.5V, 5.0V) IVOUT vs Temperature VOUT Load Regulation Buck/BuckBoost VOUT Line Regulation Buck/BuckBoost IPEAK-BUCK vs Temperature RDS(ON) of Buck PMOS/NMOS vs Temperature IPEAK_BB vs Temperature (250mA, 150mA, 100mA, 50mA) IPEAK_BB vs Temperature (25mA, 15mA, 10mA, 5mA) 3330p For more information www.linear.com/LTC3330 7 LTC3330 Typical Performance Characteristics RDS(ON) of Buck-Boost PMOS/ NMOS vs Temperature Buck Switching Waveforms Buck-Boost Switching Waveforms Buck Efficiency vs ILOAD Buck-Boost Efficiency vs ILOAD Prioritizer Buck-Boost to Buck Transition Prioritizer Buck to Buck-Boost Transition ISCAP vs SCAP Supercapacitor Balancer Source/ Sink Current 3330p 8 For more information www.linear.com/LTC3330 LTC3330 Typical Performance Characteristics ILDO_IN vs LDO_IN LDO_OUT vs Temperature LDO Load Step LDO Load Regulation LDO Line Regulation LDO Current Limit RDS(ON) of LDO PMOS LDO Start-Up 3330p For more information www.linear.com/LTC3330 9 LTC3330 Pin Functions BAL (Pin 1): Supercapacitor Balance Point. The common node of a stack of two supercapacitors is connected to BAL. A source/sink balancing current of up to 10mA is available. Tie BAL along with SCAP to GND to disable the balancer and its associated quiescent current. SCAP (Pin 2): Supply and Sense Point for Supercapacitor Balancer. Tie the top of a 2-capacitor stack to SCAP and the middle of the stack to BAL to activate balancing. Tie SCAP along with BAL to GND to disable the balancer and its associated quiescent current. VIN2 (Pin 3): Internal Low Voltage Rail to Serve as Gate Drive for Buck NMOS Switch. Connect a 4.7µF (or larger) capacitor from VIN2 to GND. This pin is not intended for use as an external system rail. UV3, UV2, UV1, UV0 (Pins 4, 5, 6, 7): UVLO Select Bits for the Buck Switching Regulator. Tie high to VIN2 or low to GND to select the desired UVLO rising and falling thresholds (see Table 4). Do not float. AC1 (Pin 8): Input Connection for Piezoelectric Element or Other AC Source (used in conjunction with AC2 for differential AC inputs). AC2 (Pin 9): Input Connection for Piezoelectric Element or Other AC Source (used in conjunction with AC1 for differential AC inputs). VIN (Pin 10): Rectified Input Voltage. A capacitor on this pin serves as an energy reservoir and input supply for the buck regulator. The VIN voltage is internally clamped to a maximum of 20V (typical). CAP (Pin 11): Internal Rail Referenced to VIN to Serve as Gate Drive for Buck PMOS Switch. Connect a 1μF (or larger) capacitor between CAP and VIN. This pin is not intended for use as an external system rail. SW (Pin 12): Switch Node for the Buck Switching Regulator. Connect a 22µH or greater external inductor between this node and VOUT. VOUT (Pin 13): Regulated Output Voltage Derived from the Buck or Buck-Boost Switching Regulator. SWB (Pin 14): Switch Node for the Buck-Boost Switching Regulator. Connect an external inductor between this node and SWA of value per Table 3. SWA (Pin 15): Switch Node for the Buck-Boost Switching Regulator. Connect an external inductor between this node and SWB of value per Table 3. BAT (Pin 16): Input for Battery. BAT serves as the input to the buck-boost switching regulator. IPK0, IPK1, IPK2 (Pins 17, 18, 19): IPEAK Select Bits for the Buck-Boost Switching Regulator. Tie high to VIN3 or low to GND to select the desired IPEAK (see Table 3). Do not float. LDO_OUT (Pin 20): Regulated LDO Output. This output can be used as a quiet supply. One mode is provided to run the LDO as a current limited switch to alternately power up and power down circuitry without low power modes. LDO_IN (Pin 21): Input Voltage for the LDO regulator. LDO2, LDO1, LDO0 (Pins 22, 23, 24): LDO Voltage Select Bits. Tie high to LDO_IN or low to GND to select the desired LDO_OUT voltage (see Table 2). Do not float. LDO_EN (Pin 25): LDO Enable Input. Active high input with logic levels referenced to LDO_IN. Do not float. VIN3 (Pin 26): Internal Low Voltage Rail Used by the Prioritizer. Connect a 1µF (or larger) capacitor from VIN3 to GND. This pin is not intended for use as an external system rail. PGLDO (Pin 27): Power Good Output for LDO_OUT. Logic level output referenced to an internal maximum rail (see Operation). PGLDO transitioning high indicates 92.5% (typical) regulation has been reached on LDO_OUT. PGLDO remains high until LDO_OUT falls to 90.0% (typical) of the programmed regulation point. PGVOUT (Pin 28): Power Good Output for VOUT. Logic level output referenced to an internal maximum rail (see Operation). PGVOUT transitioning high indicates regulation has been reached on VOUT (VOUT = Sleep Rising). PGVOUT remains high until VOUT falls to 92.5% (typical) of the programmed regulation point. BAT_ON (Pin 29): Switcher Status. Logic level output referenced to VIN3. EH_ON is high when the buck switching regulator is in use. It is pulled low when buck-boost switching regulator is in use. 3330p 10 For more information www.linear.com/LTC3330 LTC3330 Pin Functions OUT0, OUT1, OUT2 (Pins 30, 31, 32): VOUT Voltage Select Bits. Tie high to VIN3 or low to GND to select the desired VOUT (see Table 1). Do not float. GND (Exposed Pad Pin 11): Ground. The exposed pad must be connected to a continuous ground plane on the second layer of the printed circuit board by several vias directly under the LTC3330. Block Diagram 10 VIN 20V 8 INTERNAL RAIL GENERATION UVLO AC1 UVLO_SET CAP SW 9 26 AC2 VIN2 VREF 3 BUCK CONTROL BANDGAP REFERENCE PRIORITZER GND SWA BAT SWB 29 12 VIN3 SLEEP 16 11 EH_ON – VREF VOUT BUCK-BOOST CONTROL ILIM_SET 33 15 14 13 SLEEP + 28 + PGVOUT – LDO_EN SLEEP VREF 0.925*VREF 27 – PGLDO + LDO_IN – LDO_OUT + ILIM_SET – 4 4, 5, 6, 7 3 UV[3:0] 19, 18, 17 3 IPK[2:0] 21 + 0.9*VREF SCAP UVLO_SET 25 32, 31, 30 BAL 20 1 2 3 OUT[2:0] 22, 23, 24 LDO[2:0] 3330 BD 3330p For more information www.linear.com/LTC3330 11 LTC3330 Operation Modes of Operation Table 3. ILIM Selection The following four tables detail all programmable settings on the LTC3330. Table 1. Output Voltage Selection IPK2 IPK1 IPK0 ILIM LMIN 0 0 0 5mA 1100µH 0 0 1 10mA 560µH 0 1 0 15mA 360µH 0 1 1 25mA 220µH OUT2 OUT1 OUT2 VOUT 1 0 0 50mA 110µH 0 0 0 1.8V 1 0 1 100mA 56µH 0 0 1 2.5V 1 1 0 150mA 36µH 0 1 0 2.8V 1 1 1 250mA 22µH 0 1 1 3.0V 1 0 0 3.3V 1 0 1 3.6V 1 1 0 4.5V 1 1 1 5.0V Table 2. LDO Voltage Selection LDO2 LDO1 LDO0 LDO_OUT 0 0 0 1.2V 0 0 1 1.5V 0 1 0 1.8V 0 1 1 2.0V 1 0 0 2.5V 1 0 1 3.0V 1 1 0 3.3V 1 1 1 = LDO_IN Table 4. VIN UVLO Threshold Selection UV3 UV2 UV1 UV0 UVLO RISING UVLO FALLING 0 0 0 0 4V 3V 0 0 0 1 5V 4V 0 0 1 0 6V 5V 0 0 1 1 7V 6V 0 1 0 0 8V 7V 0 1 0 1 8V 5V 0 1 1 0 10V 9V 0 1 1 1 10V 5V 1 0 0 0 12V 11V 1 0 0 1 12V 5V 1 0 1 0 14V 13V 1 0 1 1 14V 5V 1 1 0 0 16V 15V 1 1 0 1 16V 5V 1 1 1 0 18V 17V 1 1 1 1 18V 5V 3330p 12 For more information www.linear.com/LTC3330 LTC3330 Operation The LTC3330 combines a buck switching regulator and a buck-boost switching regulator to produce an energy harvesting solution with battery backup. The converters are controlled by a prioritizer that selects which converter to use based on the availability of a battery and/or harvestable energy. If harvested energy is available the buck regulator is active and the buck-boost is OFF. With an optional LDO and supercapacitor balancer and an array of different configurations the LTC3330 suits many applications. BUCK CONVERTER The synchronous buck converter is an ultralow quiescent current power supply tailored to energy harvesting applications. It is designed to interface directly to a piezoelectric or alternative A/C power source, rectify the input voltage, and store harvested energy on an external capacitor while maintaining a regulated output voltage. It can also bleed off any excess input power via an internal shunt regulator. INTERNAL BRIDGE RECTIFIER An internal full-wave bridge rectifier accessible via the differential AC1 and AC2 inputs rectifies AC sources such as those from a piezoelectric element. The rectified output is stored on a capacitor at the VIN pin and can be used as an energy reservoir for the buck converter. The bridge rectifier has a total drop of about 800mV with typical piezo-generated currents (~10μA), but is capable of carrying up to 50mA. Either side of the bridge can be operated independently as single-ended AC or DC inputs. quiescent current (450nA typical) in UVLO allows energy to accumulate on the input capacitor in situations where energy must be harvested from low power sources. INTERNAL RAIL GENERATION Two internal rails, CAP and VIN2, are generated from VIN and are used to drive the high side PMOS and low side NMOS of the buck converter, respectively. Additionally the VIN2 rail serves as logic high for the UVLO threshold select bits UV[3:0]. The VIN2 rail is regulated at 4.8V above GND while the CAP rail is regulated at 4.8V below VIN. These are not intended to be used as external rails. Bypass capacitors are connected to the CAP and VIN2 pins to serve as energy reservoirs for driving the buck switches. When VIN is below 4.8V, VIN2 is equal to VIN and CAP is held at GND. Figure 1 shows the ideal VIN, VIN2 and CAP relationship. 18 16 14 VOLTAGE (V) OVERVIEW VIN 12 10 8 6 VIN2 4 CAP 2 0 0 5 10 VIN (V) 15 3330 F01 Figure 1. Ideal VIN, VIN2 and CAP Relationship BUCK OPERATION UNDERVOLTAGE LOCKOUT When the voltage on VIN rises above the UVLO rising threshold the buck converter is enabled and charge is transferred from the input capacitor to the output capacitor. When the input capacitor voltage is depleted below the UVLO falling threshold the buck converter is disabled. These thresholds can be set according to Table 4 which offers UVLO rising thresholds from 4V to 18V with large or small hysteresis windows (see Table 4). Extremely low The buck regulator uses a hysteretic voltage algorithm to control the output through internal feedback from the VOUT sense pin. The buck converter charges an output capacitor through an inductor to a value slightly higher than the regulation point. It does this by ramping the inductor current up to 260mA through an internal PMOS switch and then ramping it down to 0mA through an internal NMOS switch. This efficiently delivers energy to the output capacitor. The ramp rate is determined by VIN, 3330p For more information www.linear.com/LTC3330 13 LTC3330 Operation VOUT, and the inductor value. When the buck brings the output voltage into regulation the converter enters a low quiescent current sleep state that monitors the output voltage with a sleep comparator. During this operating mode load current is provided by the output capacitor. When the output voltage falls below the regulation point the buck regulator wakes up and the cycle repeats. This hysteretic method of providing a regulated output reduces losses associated with FET switching and maintains an output at light loads. The buck delivers a minimum of 100mA of average load current when it is switching. VOUT can be set from 1.8V to 5V via OUT[2:0] (see Table 1). When the sleep comparator signals that the output has reached the sleep threshold the buck converter may be in the middle of a cycle with current still flowing through the inductor. Normally both synchronous switches would turn off and the current in the inductor would freewheel to zero through the NMOS body diode, but the NMOS switch is kept on to prevent the conduction loss that would occur in the diode if the NMOS were off. If the PMOS is on when the sleep comparator trips the NMOS will turn on immediately in order to ramp down the current. If the NMOS is on it will be kept on until the current reaches zero. Though the quiescent current when the buck is switching is much greater than the sleep quiescent current, it is still a small percentage of the average inductor current which results in high efficiency over most load conditions. The buck operates only when sufficient energy has been accumulated in the input capacitor and the length of time the converter needs to transfer energy to the output is much less than the time it takes to accumulate energy. Thus, the buck operating quiescent current is averaged over a long period of time so that the total average quiescent current is low. This feature accommodates sources that harvest small amounts of ambient energy. BUCK-BOOST Converter The buck-boost uses the same hysteretic voltage algorithm as the buck to control the output, VOUT, with the same sleep comparator. The buck-boost has three modes of operation: buck, buck-boost, and boost. An internal mode comparator determines the mode of operation based on BAT and VOUT. Figure 2 shows the four internal switches of the buck-boost converter. In each mode the inductor current is ramped up to IPEAK. This IPEAK value is programmable via IPK[2:0] and ranges from 5mA to 250mA (see Table 3). BAT M1 SWA M2 SWB M4 VOUT M3 3330 F02 Figure 2: Buck-Boost Power Switches In BUCK mode M4 is always on and M3 is always off. The inductor current is ramped up through M1 to IPEAK and down to 0mA through M2. In boost mode M1 is always on and M2 is always off. The inductor current is ramped up to IPEAK when M3 is on and is ramped to 0mA when M4 is on as VOUT is greater than BAT in boost mode. Buckboost mode is very similar to boost mode in that M1 is always on and M2 is always off. If BAT is less than VOUT the inductor current is ramped up to IPEAK through M3. When M4 turns on the current in the inductor will start to ramp down. However, because BAT is close to VOUT and M1 and M4 have finite on-resistance the current ramp will exhibit a slow exponential decay, lowering the average current delivered to VOUT. For this reason the lower current threshold is set to IPEAK/2 in buck-boost mode to maintain high average current to the load. If BAT is greater than VOUT in buck-boost mode the inductor current still ramps up to IPEAK and down to IPEAK/2. It can still ramp down If BAT is greater than VOUT because the final value of the current in the inductor is (VIN – VOUT)/ (RON1 + RON4). If BAT is exactly IPEAK/2•(RON1 + RON4) above VOUT the inductor current will not reach the IPEAK/2 threshold and switches M1 and M4 will stay on all the time. For higher BAT voltages the mode comparator will switch the converter to buck mode. M1 and M4 will remain on for BAT voltages up to VOUT + IPEAK•(RON1 + RON4). At 3330p 14 For more information www.linear.com/LTC3330 LTC3330 Operation this point the current in the inductor is equal to IPEAK and the IPEAK comparator will trip turning off M1 and turning on M2 causing the inductor current to ramp down to IZERO, completing the transition from buck-boost mode to buck mode. A digital output, EH_ON, is low when the prioritizer has selected the BAT input and is high when the prioritizer has selected the VIN input. The EH_ON output is referenced to VIN3. VOUT Power Good An integrated low drop out regulator (LDO) is available with its own input, LDO_IN. It will regulate LDO_OUT to seven different output voltages based on the LDO[2:0] pins. An eighth mode is provided to turn the LDO into a currentlimited switch in which the PMOS is always on. LDO_EN enables the LDO when high and when low eliminates all quiescent current on LDO_IN. The LDO is designed to provide 50mA over a range of LDO_IN and LDO_OUT combinations. A current limit set above 50mA is available to dial back the current if the output is grounded or the load demands more than 50mA. The LDO also features a 1ms soft-start for smooth output start-up. A power good comparator is provided for the VOUT output. It transitions high the first time the LTC3330 goes to sleep, indicating that VOUT has reached regulation. It transitions low when VOUT falls to 92.5% (typical) of its value at regulation. The PGVOUT output is referenced to an internal rail that is generated to be the highest of VIN2, BAT, and VOUT less a Schottky diode drop. Prioritizer The input prioritizer on the LTC3330 decides whether to use the energy harvesting input or the battery input to power VOUT. If a battery is powering the buck-boost converter and harvested energy causes a UVLO rising transition on VIN, the prioritizer will shut off the buck-boost and turn on the buck, orchestrating a smooth transition that maintains regulation of VOUT. When harvestable energy disappears, the prioritizer will first poll the battery voltage. If the battery voltage is above 1.8V the prioritizer will switch back to the buck-boost while maintaining regulation. If the battery voltage is below 1.8V the buck-boost is not enabled and VOUT cannot be supported until harvestable energy is again available. If either BAT or VIN is grounded, the prioritizer allows the other input to run if its input is high enough for operation. When the prioritizer selects the VIN input the current on the BAT input drops to zero. However, if the voltage on BAT is higher than VIN2, 150nA (typical) will appear as quiescent current on BAT due to internal level shifting. This only affects a small range of battery voltages and UVLO settings. Low Drop Out Regulator A power good signal on the PGLDO pin indicates when the voltage at LDO_OUT rises above 92.5% (typical) of its final value, or after tripped, when the LDO_OUT falls below 90.0% of that value. The PGLDO output is referenced to an internal rail that is generated to be the highest of VIN2, BAT, and VOUT less a Schottky diode drop. Supercapacitor An integrated supercapacitor balancer with 165nA of quiescent current is available to balance a stack of two supercapacitors. Typically the input, SCAP, will tie to VOUT to allow for increased energy storage at VOUT with supercapacitors. The BAL pin is tied to the middle of the stack and can source and sink 10mA to regulate the BAL pin’s voltage to half that of the SCAP pin’s voltage. To disable the balancer and its associated quiescent current the SCAP and BAL pins can be tied to ground. 3330p For more information www.linear.com/LTC3330 15 LTC3330 Typical Applications 3330p 16 For more information www.linear.com/LTC3330 LTC3330 Typical Applications 3330p For more information www.linear.com/LTC3330 17 LTC3330 Typical Applications 3330p 18 For more information www.linear.com/LTC3330 LTC3330 Package Description Please refer to http://www.linear.com/designtools/packaging/ for the most recent package drawings. UH Package 32-Lead Plastic QFN (5mm × 5mm) (Reference LTC DWG # 05-08-1693 Rev D) 0.70 ±0.05 5.50 ±0.05 4.10 ±0.05 3.50 REF (4 SIDES) 3.45 ±0.05 3.45 ±0.05 PACKAGE OUTLINE 0.25 ±0.05 0.50 BSC RECOMMENDED SOLDER PAD LAYOUT APPLY SOLDER MASK TO AREAS THAT ARE NOT SOLDERED 5.00 ±0.10 (4 SIDES) BOTTOM VIEW—EXPOSED PAD 0.75 ±0.05 R = 0.05 TYP 0.00 – 0.05 R = 0.115 TYP PIN 1 NOTCH R = 0.30 TYP OR 0.35 × 45° CHAMFER 31 32 0.40 ±0.10 PIN 1 TOP MARK (NOTE 6) 1 2 3.50 REF (4-SIDES) 3.45 ±0.10 3.45 ±0.10 (UH32) QFN 0406 REV D 0.200 REF NOTE: 1. DRAWING PROPOSED TO BE A JEDEC PACKAGE OUTLINE M0-220 VARIATION WHHD-(X) (TO BE APPROVED) 2. DRAWING NOT TO SCALE 3. ALL DIMENSIONS ARE IN MILLIMETERS 4. DIMENSIONS OF EXPOSED PAD ON BOTTOM OF PACKAGE DO NOT INCLUDE MOLD FLASH. MOLD FLASH, IF PRESENT, SHALL NOT EXCEED 0.20mm ON ANY SIDE 5. EXPOSED PAD SHALL BE SOLDER PLATED 6. SHADED AREA IS ONLY A REFERENCE FOR PIN 1 LOCATION ON THE TOP AND BOTTOM OF PACKAGE 0.25 ±0.05 0.50 BSC 3330p Information furnished by Linear Technology Corporation is believed to be accurate and reliable. However, no responsibility is assumed for its use. Linear Technology Corporation makes no representaFor more information www.linear.com/LTC3330 tion that the interconnection of its circuits as described herein will not infringe on existing patent rights. 19 LTC3330 Typical Application UPS System for Wireless Mesh Networks with Output Supercapacitor Energy Storage PIEZO MIDE V25W 10µF 25V AC1 AC2 VIN SW 1µF 6V 4.7µF, 6V LTC3330 SWA CAP SWB VIN2 VOUT 100µH 100µH VOUT = 3.6V FOR EH_ON = 1 VOUT = 2.5V FOR EH_ON = 0 UV3 UV2 SCAP UV1 BAL 10mF 2.5V 22µF 6V 10mF 2.5V UV0 VSUPPLY 3.65V + Li-SOCI2 BAT 1µF 6V PGOOD PGVOUT IPK2 TX EHORBAT EH_ON IPK1 GND IPK0 LINEAR TECHNOLOGY DC9003A-A/B DUST MOTE FOR WIRELESS MESH NETWORKS OUT2 OUT1 OUT0 GND VIN3 1µF 6V 3330 TA02 Related Parts PART NUMBER DESCRIPTION COMMENTS LT1389 Nanopower Precision Shunt Voltage Reference 800nA Operating Current, 1.25V/2.5V/4.096V LTC1540 Nanopower Comparator with Reference 0.3μA IQ, Drives 0.01μF, Adjustable Hysteresis, 2V to 11V Input Range LT3009 3μA IQ, 20mA Low Dropout Linear Regulator Low 3μA IQ, 1.6V to 20V Range, 20mA Output Current LTC3108 Ultralow Voltage Step-Up Converter and Power Manager Operates from 20mV inputs, LDO, Reserve Output, Power Good LTC3109 Auto-Polarity, Ultralow Voltage Step-Up Converter and Power Manager Operates from 30mV Inputs, Auto-Polarity Architecture, LDO, Energy Storage Capability, Power Good LTC3388-1/ LTC3388-3 20V High Efficiency Nanopower Step-Down Regulator 860nA IQ in Sleep, 2.7V to 20V Input, VOUT: 1.2V to 5.0V, Enable and Standby Pins LTC3588-1 Piezoelectric Energy Harvesting Power Supply <1μA IQ in Regulation, 2.7V to 20V Input Range, Integrated Bridge Rectifier LTC3588-2 Piezoelectric Energy Harvesting Power Supply <1μA IQ in Regulation, UVLO Rising = 16V, UVLO Falling = 14V, VOUT = 3.45V, 4.1V, 4.5V, 5.0V LTC4070 Li-Ion/Polymer Shunt Battery Charger System 450nA IQ, 1% Float Voltage Accuracy, 50mA Shunt Current 4.0V/4.1V/4.2V LTC4071 Li-Ion/Polymer Shunt Battery Charger System with Low Battery Disconnect 550nA IQ, 1% Float Voltage Accuracy, 50mA Shunt Current 4.0V/4.1V/4.2V, 2.7V or 3.2V Battery Disconnect Levels 3330p 20 Linear Technology Corporation 1630 McCarthy Blvd., Milpitas, CA 95035-7417 For more information www.linear.com/LTC3330 (408) 432-1900 ● FAX: (408) 434-0507 ● www.linear.com/LTC3330 LT 0313 • PRINTED IN USA LINEAR TECHNOLOGY CORPORATION 2013