Si413 3 Si4 123 /2 2/13 /1 2 D U A L -B A N D R F S Y N T H E S I Z E R W I T H I N T E G R A T E D V C O S FO R WIRELESS COM MUNICATIONS ! Integrated VCOs, Loop Filters, ! Varactors, and Resonators Minimal (2) External Components Required Ordering Information: See page 31. Applications Dual-Band Communications Digital Cellular Telephones GSM, DCS1800, PCS1900 ! ! ! Digital Cordless Phones Analog Cordless Phones Wireless LAN and WAN Si4133-BT Description The Si4133 is a monolithic integrated circuit that performs both IF and dualband RF synthesis for wireless communications applications. The Si4133 includes three VCOs, loop filters, reference and VCO dividers, and phase detectors. Divider and power-down settings are programmable through a three-wire serial interface. Functional Block Diagram GNDI RFLC 5 20 IFLB GNDR 6 19 IFLA RFLB 7 18 GNDD RFLA 8 17 V DDD GNDR 9 16 GNDD GNDR 10 15 XIN RFOUT 11 14 PWDNB V DDR 12 13 A UXOUT R FLB R F1 ÷N Si4133-BM R FLC P hase D etector R FLD IFOUT R FO UT GNDI ÷R 28 27 26 25 24 23 22 R F2 22-bit D ata R egister Test Mux IFOUT 21 GNDR 1 21 GNDI RFLD 2 20 IFLB ÷N ÷R P hase D etector IFD IV RFLC 3 19 IFLA GNDR 4 18 GNDD RFLB 5 17 V DDD RFLA 6 16 GNDD GNDR 7 15 XIN IFO U T IF ÷N IFLA IFLB 8 9 10 11 12 13 14 GNDD A U XO U T 22 4 PWDNB S E NB 3 RFLD R FLA P hase D etector P ow er D ow n C ontrol S erial Interface GNDR V DDI S C LK V DDI SENB S D AT A SENB 23 V DDR PW DNB ÷R 24 2 A UXOUT R eference A m plifier 1 SCLK X IN SCLK SDA TA RFOUT ! SDA TA ! Pin Assignments GNDR ! ! IF: 62.5 MHz to 1000 MHz GNDR " ! ! IF Synthesizer GNDR " ! Low Phase Noise Programmable Power Down Modes 1 µA Standby Current 18 mA Typical Supply Current 2.7 V to 3.6 V Operation Packages: 24-Pin TSSOP, 28-Lead MLP ! ! RF1: 900 MHz to 1.8 GHz RF2: 750 MHz to 1.5 GHz i4 Dual-Band RF Synthesizers " S ! 13 3- B T Features Patents pending Rev. 1.1 3/01 Copyright © 2001 by Silicon Laboratories Si4133-DS11 This information applies to a product under development. Its characteristics and specifications are subject to change without notice. S i4 13 3 2 Rev. 1.1 Si4133 TA B L E O F C O N T E N T S Section Page Electrical Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Functional Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Serial Interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Setting the VCO Center Frequencies . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Extended Frequency Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Self-Tuning Algorithm . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Output Frequencies . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . PLL Loop Dynamics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . RF and IF Outputs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Reference Frequency Amplifier . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Power Down Modes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Auxiliary Output (AUXOUT) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Control Registers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Pin Descriptions: Si4133-BT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Pin Descriptions: Si4133-BM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Ordering Guide . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Si4133 Derivative Devices . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Package Outline: Si4133-BT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Package Outline: Si4133-BM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Contact Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Rev. 1.1 4 16 16 16 17 17 18 18 19 19 19 20 21 27 29 31 31 32 33 34 3 S i4 13 3 Electrical Specifications Table 1. Recommended Operating Conditions Parameter Symbol Test Condition Min Typ Max Unit Ambient Temperature TA –40 25 85 °C Supply Voltage VDD 2.7 3.0 3.6 V Supply Voltages Difference V∆ –0.3 — 0.3 V (VDDR – VDDD), (VDDI – VDDD) Note: All minimum and maximum specifications are guaranteed and apply across the recommended operating conditions. Typical values apply at nominal supply voltages and an operating temperature of 25°C unless otherwise stated. Table 2. Absolute Maximum Ratings1,2 Parameter Symbol Value Unit VDD –0.5 to 4.0 V Input Current3 IIN ±10 mA Input Voltage3 VIN –0.3 to VDD+0.3 V TSTG –55 to 150 DC Supply Voltage Storage Temperature Range o C Notes: 1. Permanent device damage may occur if the above Absolute Maximum Ratings are exceeded. Functional operation should be restricted to the conditions as specified in the operational sections of this data sheet. Exposure to absolute maximum rating conditions for extended periods may affect device reliability. 2. This device is a high performance RF integrated circuit with an ESD rating of < 2 kV. Handling and assembly of this device should only be done at ESD-protected workstations. 3. For signals SCLK, SDATA, SENB, PWDNB and XIN. 4 Rev. 1.1 Si4133 Table 3. DC Characteristics (VDD = 2.7 to 3.6 V, TA = –40 to 85°C) Parameter Symbol Test Condition Min Typ Max Unit RF1 and IF operating — 18 27 mA RF1 Mode Supply Current1 — 10 16 mA RF2 Mode Supply Current1 — 9 16 mA IF Mode Supply Current1 — 8 13 mA — 1 — µA 1 Total Supply Current Standby Current PWDNB = 0 High Level Input Voltage2 VIH 0.7 VDD — — V Low Level Input Voltage2 VIL — — 0.3 VDD V High Level Input Current2 IIH VIH = 3.6 V, VDD = 3.6 V –10 — 10 µA Low Level Input Current2 IIL VIL = 0 V, VDD= 3.6 V –10 — 10 µA High Level Output Voltage3 VOH IOH = –500 µA VDD–0.4 — — V Low Level Output Voltage3 VOL IOH = 500 µA — — 0.4 V Notes: 1. RF1 = 1.6 GHz, RF2 = 1.1 GHz, IFOUT = 550 MHz, LPWR = 0 2. For signals SCLK, SDATA, SENB, and PWDNB. 3. For signal AUXOUT. Rev. 1.1 5 S i4 13 3 Table 4. Serial Interface Timing (VDD = 2.7 to 3.6 V, TA = –40 to 85°C) Symbol Test Condition Min Typ Max Unit SCLK Cycle Time tclk Figure 1 40 — — ns SCLK Rise Time tr Figure 1 — — 50 ns SCLK Fall Time tf Figure 1 — — 50 ns SCLK High Time th Figure 1 10 — — ns SCLK Low Time tl Figure 1 10 — — ns SDATA Setup Time to SCLK↑2 tsu Figure 2 5 — — ns SDATA Hold Time from SCLK↑2 Parameter1 thold Figure 2 0 — — ns 2 SENB↓ to SCLK↑ Delay Time ten1 Figure 2 10 — — ns SCLK↑ to SENB↑ Delay Time2 ten2 Figure 2 12 — — ns SENB↑ to SCLK↑ Delay Time2 ten3 Figure 2 12 — — ns tw Figure 2 10 — — ns SENB Pulse Width Notes: 1. All timing is referenced to the 50% level of the waveforms unless otherwise noted. 2. Timing is not referenced to 50% level of the waveform. See Figure 2. tr tf 80% S CLK 50% 20% th t clk tl Figure 1. SCLK Timing Diagram 6 Rev. 1.1 Si4133 ts u thold S CLK S DA TA D17 D16 D15 A1 A0 ten3 ten1 ten2 S E NB tw Figure 2. Serial Interface Timing Diagram First bit c loc ked in Las t bit c loc ked in D D D D D D D D D 17 16 15 14 13 12 11 10 9 D 8 D 7 D 6 D D 5 4 D 3 D 2 D 1 data field D 0 A 3 A 2 A 1 A 0 addres s field Figure 3. Serial Word Format Rev. 1.1 7 S i4 13 3 Table 5. RF and IF Synthesizer Characteristics (VDD = 2.7 to 3.6 V, TA = –40 to 85°C) Parameter1 Symbol Test Condition Min Typ Max Unit XIN Input Frequency fREF 2 — 26 MHz Reference Amplifier Sensitivity VREF 0.5 — VDD +0.3 V VP-P 0.010 — 1.0 MHz 947 — 1720 MHz 1850 — 2050 MHz 789 — 1429 MHz –5 — 5 % 526 — 952 MHz with IFDIV 62.5 — 1000 MHz Note: LEXT ±10% –5 — 5 % Open loop — 500 — kHz/V RF2 VCO Pushing — 400 — kHz/V IF VCO Pushing — 300 — kHz/V — 900 — MHz — 300 — kHz — 100 — kHz 1 MHz offset — –132 — dBc/Hz 10 Hz to 100 kHz — 0.9 — degrees rms 1 MHz offset — –134 — dBc/Hz 10 Hz to 100 kHz — 0.7 — degrees rms 100 kHz offset — –117 — dBc/Hz 100 Hz to 100 kHz — 0.4 — degrees rms Phase Detector Update Frequency fφ RF1 VCO Center Frequency Range fCEN RF1 VCO Tuning Range2 RF2 VCO Center Frequency Range Extended frequency operation fCEN RF Tuning Range from fCEN IF VCO Center Frequency Range IFOUT Tuning Range IFOUT Tuning Range from fCEN RF1 VCO Pushing RF1 VCO Pulling RF2 VCO Pulling fφ = fREF/R Note: LEXT ±10% fCEN VSWR = 2:1, all phases, open loop IF VCO Pulling RF1 Phase Noise RF1 Integrated Phase Error RF2 Phase Noise RF2 Integrated Phase Error IF Phase Noise IF Integrated Phase Error Notes: 1. fφ = 200 kHz, RF1 = 1.6 GHz, RF2 = 1.2 GHz, IFOUT = 550 MHz, LPWR = 0, for all parameters unless otherwise noted. 2. Extended frequency operation only. VDD ≥ 3.0 V, MLP only, VCO Tuning Range fixed by directly shorting the RFLA and RFLB pins. See Application Note 41 for more details on the Si4133 extended frequency operation. 3. From power up request (PWDNB↑ or SENB↑ during a write of 1 to bits PDIB and PDRB in Register 2) to RF and IF synthesizers ready (settled to within 0.1 ppm frequency error). 4. From power down request (PWDNB↓, or SENB↑ during a write of 0 to bits PDIB and PDRB in Register 2) to supply current equal to IPWDN. 8 Rev. 1.1 Si4133 Table 5. RF and IF Synthesizer Characteristics (Continued) (VDD = 2.7 to 3.6 V, TA = –40 to 85°C) Symbol Test Condition Min Typ Max Unit Second Harmonic — –26 –20 dBc RF2 Harmonic Suppression — –26 –20 dBc IF Harmonic Suppression — –26 –20 dBc ZL = 50 Ω –8 –3 1 dBm RFOUT Power Level ZL = 50 Ω, RF1 active, Extended frequency operation –14 –7 1 dBm IFOUT Power Level ZL = 50 Ω –8 –4 0 dBm Offset = 200 kHz — –65 — dBc Offset = 400 kHz — –71 — dBc Offset = 600 kHz — –75 — dBc Offset = 200 kHz — –65 — dBc Offset = 400 kHz — –71 — dBc Offset = 600 kHz — –75 — dBc Parameter1 RF1 Harmonic Suppression RFOUT Power Level 2 RF1 Output Reference Spurs RF2 Output Reference Spurs Power Up Request to Synthesizer Ready3 Time tpup Figures 4, 5 — 40/fφ 50/fφ Power Down Request to Synthesizer Off4 Time tpdn Figures 4, 5 — — 100 ns Notes: 1. fφ = 200 kHz, RF1 = 1.6 GHz, RF2 = 1.2 GHz, IFOUT = 550 MHz, LPWR = 0, for all parameters unless otherwise noted. 2. Extended frequency operation only. VDD ≥ 3.0 V, MLP only, VCO Tuning Range fixed by directly shorting the RFLA and RFLB pins. See Application Note 41 for more details on the Si4133 extended frequency operation. 3. From power up request (PWDNB↑ or SENB↑ during a write of 1 to bits PDIB and PDRB in Register 2) to RF and IF synthesizers ready (settled to within 0.1 ppm frequency error). 4. From power down request (PWDNB↓, or SENB↑ during a write of 0 to bits PDIB and PDRB in Register 2) to supply current equal to IPWDN. Rev. 1.1 9 S i4 13 3 RF and IF sy nthes iz ers settled to w ithin 0.1 ppm f requency error. tpup IT RF and IF synthes izers settled to w ithin 0.1 ppm f requenc y error. tpdn IT I PW D N IPW D N S E NB P W DNB S DA TA PD IB = 1 PD R B = 1 tpdn PD IB = 0 PD R B = 0 Figure 4. Software Power Management Timing Diagram 10 tpup Figure 5. Hardware Power Management Timing Diagram Rev. 1.1 Si4133 TRACE A: Ch1 FM Main Time A Marker 1.424 kHz 174.04471 us 711.00 Hz Real 160 Hz /div 176 Hz Start: 0 s Stop: 399.6003996 us Figure 6. Typical Transient Response RF1 at 1.6 GHz with 200 kHz Phase Detector Update Frequency Rev. 1.1 11 S i4 13 3 −60 −70 Phase Noise (dBc/Hz) −80 −90 −100 −110 −120 −130 −140 2 10 3 10 4 10 Offset Frequency (Hz) 5 10 Figure 7. Typical RF1 Phase Noise at 1.6 GHz with 200 kHz Phase Detector Update Frequency Figure 8. Typical RF1 Spurious Response at 1.6 GHz with 200 kHz Phase Detector Update Frequency 12 Rev. 1.1 6 10 Si4133 −60 −70 Phase Noise (dBc/Hz) −80 −90 −100 −110 −120 −130 −140 2 10 3 10 4 10 Offset Frequency (Hz) 5 10 6 10 Figure 9. Typical RF2 Phase Noise at 1.2 GHz with 200 kHz Phase Detector Update Frequency Figure 10. Typical RF2 Spurious Response at 1.2 GHz with 200 kHz Phase Detector Update Frequency Rev. 1.1 13 S i4 13 3 −70 −80 Phase Noise (dBc/Hz) −90 −100 −110 −120 −130 −140 −150 2 10 3 10 4 10 Offset Frequency (Hz) 5 10 Figure 11. Typical IF Phase Noise at 550 MHz with 200 kHz Phase Detector Update Frequency Figure 12. IF Spurious Response at 550 MHz with 200 kHz Phase Detector Update Frequency 14 Rev. 1.1 6 10 Si4133 VDD S i4133 -B T F ro m 1 S ys te m SENB SCLK 30 Ω * 24 0 .0 2 2 µ F C o n tro lle r 2 VDDI S D ATA 23 10nH 3 IFO U T GNDR 4 RFLD GNDI RFLC IFL B GNDR IFL A 5 6 P rinte d Tra c e Ind uc tors 7 8 9 RFLB GNDD RFLA VDDD GNDR GNDD GNDR X IN 5 6 0 pF 22 IFO U T 21 P rinte d Tra c e Ind uc tor o r C h ip In d uc to r 20 19 18 17 0.022µ F V DD 16 5 6 0 pF 10 5 6 0 pF 15 E x te rna l C loc k 2nH 11 RFOUT PW DNB RFOUT 0.022µ F 14 PW DNB V DD 12 AU X O U T VDDR 13 AU X O U T * Ad d 3 0 Ω s e rie s re s is ta nc e if u s ing IF ou tpu t divid e v a lue s 2 , 4 , o r 8 . Figure 13. Typical Application Circuit: Si4133-BT VDD 30 Ω * F ro m 0.022 µ F 10nH S ys te m 560pF C o n tro lle r IFO U T 2 3 P rinte d Tra c e Ind u c tors 4 5 6 22 G NDI 23 IF OUT 24 V DDI 25 SEN B SD ATA 1 26 SC LK 27 G NDR 28 GNDR GNDI RFLD IFL B RFLC IFL A S i4133 -B M GNDR GNDD RFLB VDDD RFLA GNDD P rinte d Tra c e Ind u c tor o r C h ip In d uc tor 21 20 19 18 V DD 17 16 0.022µ F 8 9 10 11 12 13 X IN 15 E x te rna l C loc k GNDD PWD NB AUXOUT VDDR GNDR GNDR GNDR RFOUT 560pF 7 14 V DD 0.022 µ F AUXOUT PW DNB 2nH 560pF RFO UT * Ad d 3 0 Ω s e rie s re s is ta nc e if us in g IF ou tp ut d iv id e va lu e s 2 , 4 , o r 8 . Figure 14. Typical Application Circuit: Si4133-BM Rev. 1.1 15 S i4 13 3 Functional Description The Si4133 is a monolithic integrated circuit that performs IF and dual-band RF synthesis for wireless communications applications. This integrated circuit (IC), with minimal external components, completes the frequency synthesis function necessary for RF communications systems. The Si4133 has three complete phase-locked loops (PLLs) with integrated voltage-controlled oscillators (VCOs). The low phase noise of the VCOs makes the Si4133 suitable for use in demanding wireless communications applications. Phase detectors, loop filters, and reference and output frequency dividers are integrated. The IC is programmed through a three-wire serial interface. Two PLLs are provided for dual-band RF synthesis. These RF PLLs are multiplexed so that only one PLL is active at a given time (as determined by the setting of an internal register). The active PLL is the last one written. The center frequency of the VCO in each PLL is set by the value of an external inductance. Inaccuracies in these inductances are compensated for by the selftuning algorithm. The algorithm is run following powerup or following a change in the programmed output frequency. The unique PLL architecture used in the Si4133 produces settling (lock) times that are comparable in speed to fractional-N architectures without suffering the high phase noise or spurious modulation effects often associated with those designs. Serial Interface A timing diagram for the serial interface is shown in Figure 2 on page 7. Figure 3 on page 7 shows the format of the serial word. The Si4133 is programmed serially with 22-bit words comprised of 18-bit data fields and 4-bit address fields. When the serial interface is enabled (i.e., when SENB is low) data and address bits on the SDATA pin are clocked into an internal shift register on the rising edge of SCLK. Data in the shift register is then transferred on the rising edge of SENB into the internal data register addressed in the address field. The serial interface is disabled when SENB is high. Table 12 on page 21 summarizes the data register functions and addresses. The internal shift register will ignore any leading bits before the 22 required bits. Setting the VCO Center Frequencies Each RF PLL, when active, can adjust the RF output frequency by ±5% of its VCO’s center frequency. Because the two VCOs can be set to have widely separated center frequencies, the RF output can be programmed to service two widely separated frequency bands by simply programming the corresponding NDivider. One RF VCO is optimized to have its center frequency set between 947 MHz and 1.72 GHz, while the second RF VCO is optimized to have its center frequency set between 789 MHz and 1.429 GHz. The PLLs can adjust the IF and RF output frequencies ±5% of the center frequencies of their VCOs. Each center frequency is established by the value of an external inductance connected to the respective VCO. Manufacturing tolerances of ±10% for the external inductances are acceptable. The Si4133 will compensate for inaccuracies in each inductance by executing a self-tuning algorithm following PLL powerup or following a change in the programmed output frequency. One PLL is provided for IF frequency synthesis. The center frequency of this circuit’s VCO is set by connection of an external inductance. The PLL can adjust the IF output frequency by ±5% of the VCO center frequency. Inaccuracies in the value of the external inductance are compensated for by the Si4133’s proprietary self-tuning algorithm. This algorithm is initiated each time the PLL is powered-up (by either the PWDNB pin or by software) and/or each time a new output frequency is programmed. Because the total tank inductance is in the low nH range, the inductance of the package needs to be considered in determining the correct external inductance. The total inductance (LTOT) presented to each VCO is the sum of the external inductance (LEXT) and the package inductance (LPKG). Each VCO has a nominal capacitance (CNOM) in parallel with the total inductance, and the center frequency is as follows: The IF VCO can have its center frequency set as low as 526 MHz and as high as 952 MHz. An IF output divider is provided to divide down the IF output frequencies, if needed. The divider is programmable, capable of dividing by 1, 2, 4, or 8. 16 Rev. 1.1 Si4133 1 f CEN = --------------------------------------------2π L TOT ⋅ C NOM or 1 fCEN = ---------------------------------------------------------------------2π ( L PKG + L EXT ) ⋅ CNOM Tables 6 and 7 summarize the characteristics of each VCO. Table 6. Si4133-BT VCO Characteristics VCO fCEN Range (MHz) CNOM (pF) LPKG (nH) LEXT Range (nH) Min Max For more information on designing the external trace inductors, refer to Application Note 31. 2.0 0.0 4.6 Extended Frequency Operation 4.8 2.3 0.3 6.2 6.5 2.1 2.2 12.0 The Si4133 may operate at an extended frequency range of 1850 MHz to 2050 MHz by connecting the RFLA and RFLB pins directly. For information on configuring the Si4133 for extended frequency operation, refer to Application Note 41. Min Max RF1 947 1720 4.3 RF2 789 1429 IF 526 952 Table 7. Si4133-BM VCO Characteristics VCO fCEN Range (MHz) 1145 MHz. The center frequency should be defined as midway between the two extremes, or 1132.5 MHz. The PLL will be able to adjust the VCO output frequency ±5% of the center frequency, or ±56.6 MHz of 1132.5 MHz (i.e., from approximately 1076 MHz to 1189 MHz). The RF2 VCO has a CNOM of 4.8 pF. A 4.1 nH inductance (correct to two digits) in parallel with this capacitance will yield the desired center frequency. An external inductance of 1.8 nH should be connected between RFLC and RFLD as shown in Figure 15. This, in addition to 2.3 nH of package inductance, will present the correct total inductance to the VCO. In manufacturing, the external inductance can vary ±10% of its nominal value and the Si4133 will correct for the variation with the self-tuning algorithm. CNOM (pF) Min Max RF1 947 1720 4.3 RF2 789 1429 IF 526 952 LPKG (nH) Self-Tuning Algorithm LEXT Range (nH) Min Max 1.5 0.5 5.1 4.8 1.5 1.1 7.0 6.5 1.6 2.7 12.5 The self-tuning algorithm is initiated immediately following power-up of a PLL or, if the PLL is already powered, following a change in its programmed output frequency. This algorithm attempts to tune the VCO so that its free-running frequency is near the desired output frequency. In doing so, the algorithm will compensate for manufacturing tolerance errors in the value of the external inductance connected to the VCO. It will also reduce the frequency error for which the PLL must correct to get the precise desired output frequency. The self-tuning algorithm will leave the VCO oscillating at a frequency in error by somewhat less than 1% of the desired output frequency. After self-tuning, the PLL controls the VCO oscillation frequency. The PLL will complete frequency locking, eliminating any remaining frequency error. Thereafter, it will maintain frequency-lock, compensating for effects caused by temperature and supply voltage variations. L PK G 2 L EXT L PK G 2 Figure 15. External Inductance Connection As a design example, suppose the goal is to synthesize frequencies in a 25 MHz band between 1120 MHz and The Si4133’s self-tuning algorithm will compensate for component value errors at any temperature within the specified temperature range. However, the ability of the PLL to compensate for drift in component values that occur after self-tuning is limited. For external inductances with temperature coefficients around ±150 ppm/oC, the PLL will be able to maintain lock for changes in temperature of approximately ±30 oC. Rev. 1.1 17 S i4 13 3 Applications where the PLL is regularly powered-down or the frequency is periodically reprogrammed minimize or eliminate the potential effects of temperature drift because the VCO is re-tuned in either case. In applications where the ambient temperature can drift substantially after self-tuning, it may be necessary to monitor the lock-detect bar (LDETB) signal on the AUXOUT pin to determine whether a PLL is about to run out of locking capability. (See “Auxiliary Output (AUXOUT)” for how to select LDETB.) The LDETB signal will be low after self-tuning has completed but will rise when either the IF or RF PLL nears the limit of its compensation range. (LDETB will also be high when either PLL is executing the self-tuning algorithm.) The output frequency will still be locked when LDETB goes high, but the PLL will eventually lose lock if the temperature continues to drift in the same direction. Therefore, if LDETB goes high both the IF and RF PLLs should promptly be re-tuned by initiating the self-tuning algorithm. PLL Loop Dynamics The transient response for each PLL is determined by its phase detector update rate fφ (equal to fREF/R) and the phase detector gain programmed for each RF1, RF2, or IF synthesizer. (See Register 1.) Four different settings for the phase detector gain are available for each PLL. The highest gain is programmed by setting the two phase detector gain bits to 00, and the lowest by setting the bits to 11. The values of the available gains, relative to the highest gain, are as follows: Table 8. Gain Values (Register 1) KP Bits Relative P.D. Gain 00 1 01 1/2 10 1/4 11 1/8 Output Frequencies The IF and RF output frequencies are set by programming the R- and N-Divider registers. Each PLL has its own R and N registers so that each can be programmed independently. Programming either the Ror N-Divider register for RF1 or RF2 automatically selects the associated output. The reference frequency on the XIN pin is divided by R and this signal is input to the PLL’s phase detector. The other input to the phase detector is the PLL’s VCO output frequency divided by N. The PLL acts to make these frequencies equal. That is, after an initial transient The gain value bits can be automatically set by setting the Auto KP bit (bit 2) in the Main Configuration register to 1. In setting this bit, the gain values will be optimized for a given value of N. In general, a higher phase detector gain will decrease in-band phase noise and increase the speed of the PLL transient until the point at which stability begins to be compromised. The optimal gain depends on N. Table 9 lists recommended settings for different values of N. These are the settings used when the Auto KP bit is set. Table 9. Optimal KP Settings f OUT fREF ----------- = ----------N R N RF1 KP1<1:0> RF2 KP2<3:2> IF KPI<5:4> ≤2047 00 00 00 2048 to 4095 00 00 01 4096 to 8191 00 01 10 8192 to 16383 01 10 11 16384 to 32767 10 11 11 ≥32768 11 11 11 or fOUT N = ---- ⋅ fREF R The R values are set by programming the RF1 RDivider register (Register 6), the RF2 R-Divider register (Register 7) and the IF R-Divider register (Register 8). The N values are set by programming the RF1 NDivider register (Register 3), the RF2 N-Divider register (Register 4), and the IF N-Divider register (Register 5). Each N-Divider is implemented as a conventional high speed divider. That is, it consists of a dual-modulus prescaler, a swallow counter, and a lower speed synchronous counter. However, the control of these sub-circuits is handled automatically. Only the appropriate N value should be programmed. 18 The VCO gain and loop filter characteristics are not programmable. The settling time for the PLL is directly proportional to its phase detector update period Tφ (Tφ equals 1/fφ). A typical transient response is shown in Figure 6 on page 11. During the first 13 update periods the Si4133 executes the self-tuning algorithm. Thereafter the PLL Rev. 1.1 Si4133 controls the output frequency. Because of the unique architecture of the Si4133 PLLs, the time required to settle the output frequency to 0.1 ppm error is only about 25 update periods. Thus, the total time after power-up or a change in programmed frequency until the synthesized frequency is well settled—including time for self-tuning—is around 40 update periods. 560 pF IFOUT L MATCH 50 Ω Note: The settling time analysis holds for RF1 fφ ≤ 500 kHz. For RF1 fφ > 500 kHz, the settling time is larger. Figure 16. IF Frequencies > 500 MHz RF and IF Outputs The RFOUT and IFOUT pins are driven by amplifiers that buffer the RF VCOs and IF VCO, respectively. The RF output amplifier receives its input from either the RF1 or RF2 VCO, depending upon which R- or NDivider register was last written. For example, programming the N-Divider register for RF1 automatically selects the RF1 VCO output. Figures 13 and 14 show application diagrams for the Si4133. The RF output signal must be AC coupled to its load through a capacitor. An external inductance between the RFOUT pin and the AC coupling capacitor is required as part of an output matching network to maximize power delivered to the load. This 2 nH inductance may be realized with a PC board trace. The network is made to provide an adequate match to an external 50 Ω load for both the RF1 and RF2 frequency bands. The matching network also filters the output signal to reduce harmonic distortion. The IFOUT pin must also be AC coupled to its load through a capacitor. The IF output level is dependent upon the load. Figure 18 on page 20 displays the output level versus load resistance for a variety of output frequencies. For resistive loads greater than 500 Ω the output level saturates and the bias currents in the IF output amplifier are higher than they need to be. The LPWR bit in the Main Configuration register (Register 0) can be set to 1 to reduce the bias currents and therefore reduce the power dissipated by the IF amplifier. For loads less than 500 Ω, LPWR should be set to 0 to maximize the output level. For IF frequencies greater than 500 MHz, a matching network is required in order to drive a 50 Ω load. See Figure 16 below. The value of LMATCH can be determined from Table 10. Table 10. LMATCH Values Frequency LMATCH 500–600 MHz 40 nH 600–800 MHz 27 nH 800 MHz–1 GHz 18 nH For frequencies less than 500 MHz, the IF output buffer can directly drive a 200 Ω resistive load or higher. For resistive loads greater than 500 Ω (f < 500 MHz) the LPWR bit can be set to reduce the power consumed by the IF output buffer. See Figure 17 below. >500 pF IFOUT >200 Ω Figure 17. IF Frequencies < 500 MHz Reference Frequency Amplifier The Si4133 provides a reference frequency amplifier. If the driving signal has CMOS levels it can be connected directly to the XIN pin. Otherwise, the reference frequency signal should be AC coupled to the XIN pin through a 560 pF capacitor. Power Down Modes Table 11 summarizes the power down functionality. The Si4133 can be powered down by taking the PWDNB pin low or by setting bits in the Power Down register (Register 2). When the PWDNB pin is low, the Si4133 will be powered down regardless of the Power Down register settings. When the PWDNB pin is high, power management is under control of the Power Down register bits. The IF and RF sections of the Si4133 circuitry can be individually powered down by setting the Power Down register bits PDIB and PDRB low, respectively. Note that the reference frequency amplifier will also be powered up if either the PDRB and PDIB bits are high. Also, setting the AUTOPDB bit to 1 in the Main Configuration register (Register 0) is equivalent to setting both bits in the Power Down register to 1. The serial interface remains available and can be written in all power down modes. Rev. 1.1 19 S i4 13 3 Auxiliary Output (AUXOUT) The signal appearing on AUXOUT is selected by setting the AUXSEL bits in the Main Configuration register (Register 0). The LDETB signal can be selected by setting the AUXSEL bits to 11. This signal can be used to indicate that the IF or RF PLL is about to lose lock due to excessive ambient temperature drift and should be re-tuned. Table 11. Power Down Configuration PWDNB Pin AUTOPDB PDIB PDRB IF Circuitry RF Circuitry PWDNB = 0 X X X OFF OFF 0 0 0 OFF OFF 0 0 1 OFF ON 0 1 0 ON OFF 0 1 1 ON ON 1 x x ON ON PWDNB = 1 450 400 350 LPWR=1 LPWR=0 Output Voltage (mVrms) 300 250 200 150 100 50 0 0 200 400 600 800 1000 Load Resistance (Ω Ω) Figure 18. Typical IF Output Voltage vs. Load Resistance at 550 MHz 20 Rev. 1.1 1200 Si4133 Control Registers Table 12. Register Summary Register Name Bit Bit Bit Bit 17 16 15 14 Bit 13 Bit 12 Main Configuration 0 1 Phase Detector Gain 0 0 0 0 0 0 0 2 Power Down 0 0 0 0 0 0 0 0 3 0 0 0 AUXSEL [1:0] Bit 11 Bit Bit Bit Bit Bit 10 9 8 7 6 IFDIV 6 0 0 0 0 0 0 KPI[1:0] KP2[1:0] 0 0 0 0 0 0 0 [1:0] 0 0 0 RF1 0 0 0 0 0 RRF1[12:0] 0 0 0 0 0 RRF2[12:0] 0 0 0 0 0 RIF[12:0] IF R-Divider 9 Reserved RF PWR 0 KP1[1:0] PDIB PDRB NIF[15:0] R-Divider 8 0 Bit 0 NRF2[16:0] IF N-Divider RF2 0 AUTO AUTO PDB KP Bit 1 NRF1[17:0] R-Divider 7 0 Bit 2 0 N-Divider 5 LPWR Bit 3 0 RF1 RF2 Bit 4 0 N-Divider 4 Bit 5 . . . 15 Reserved Note: Registers 9–15 are reserved. Writes to these registers may result in unpredictable behavior. Any register not listed here is reserved and should not be written. Rev. 1.1 21 S i4 13 3 Register 0. Main Configuration Address Field = A[3:0] = 0000 Bit D17 D16 D15 D14 D13 D12 D11 D10 D9 Name 22 0 0 0 0 AUXSEL IFDIV [1:0] [1:0] 0 D8 D7 D6 D5 D4 D3 D2 D1 D0 0 0 0 LPWR 0 AUTO PDB AUTO KP RF PWR 0 Bit Name Function 17:14 Reserved 13:12 AUXSEL[1:0] Auxiliary Output Pin Definition. 00 = Reserved. 01 = Force output low. 10 = Reserved. 11 = Lock Detect—LDETB. 11:10 IFDIV[1:0] IF Output Divider. 00 = IFOUT = IFVCO Frequency 01 = IFOUT = IFVCO Frequency/2 10 = IFOUT = IFVCO Frequency/4 11 = IFOUT = IFVCO Frequency/8 9:6 Reserved Program to zero. 5 LPWR 4 Reserved Program to zero. 3 AUTOPDB Auto Power Down. 0 = Software powerdown is controlled by Register 2. 1 = Equivalent to setting all bits in Register 2 = 1. 2 AUTOKP Auto KP Setting. 0 = KPs are controlled by Register 1. 1 = KPs are set according to Table 9 on page 18. 1 RFPWR Program to zero. (Used for extended frequency operation. See AN41 for more information.) 0 Reserved Program to zero. Output Power-Level Settings for IF Synthesizer Circuit. 0 = RLOAD < 500 Ω—normal power mode. 1 = RLOAD ≥ 500 Ω—low power mode. Program to zero. Rev. 1.1 Si4133 Register 1. Phase Detector Gain Address Field (A[3:0]) = 0001 Bit Name D17 D16 D15 D14 D13 D12 D11 D10 0 0 0 0 0 0 0 D9 D8 D7 D6 0 0 0 0 0 Bit Name 17:6 Reserved 5:4 KPI[1:0] IF Phase Detector Gain Constant.* N Value KPI <2048 = 00 2048–4095 = 01 4096–8191 = 10 >8191 = 11 3:2 KP2[1:0] RF2 Phase Detector Gain Constant.* N Value KP2 <4096 = 00 4096–8191 = 01 8192–16383 = 10 >16383 = 11 1:0 KP1[1:0] RF1 Phase Detector Gain Constant.* N Value KP1 <8192 = 00 8192–16383 = 01 16384–32767 = 10 >32767 = 11 D5 D4 KPI[1:0] D3 D2 KP2[1:0] D1 D0 KP1[1:0] Function Program to zero. *Note: When AUTOKP = 1, these bits do not need to be programmed. When AUTOKP = 0, use these recommended values for programming Phase Detector Gain. Rev. 1.1 23 S i4 13 3 Register 2. Power Down Address Field (A[3:0]) = 0010 Bit D17 D16 D15 D14 D13 D12 D11 D10 D9 Name 0 0 0 0 0 0 0 0 D8 D7 D6 D5 D4 D3 D2 0 0 0 0 0 0 0 0 Bit Name 17:2 Reserved 1 PDIB Power Down IF Synthesizer. 0 = IF synthesizer powered down. 1 = IF synthesizer on. 0 PDRB Power Down RF Synthesizer. 0 = RF synthesizer powered down. 1 = RF synthesizer on. D1 D0 PDIB PDRB Function Program to 0. Note: Enabling any PLL with PDIB or PDRB will automatically power on the reference amplifier. Register 3. RF1 N-Divider Address Field (A[3:0]) = 0011 Bit D17 D16 D15 D14 D13 D12 D11 D10 Name D9 D8 D7 D6 D5 D4 D3 D2 D1 D0 D5 D4 D3 D2 D1 D0 NRF1[17:0] Bit Name 17:0 NRF1[17:0] Function N-Divider for RF1 Synthesizer. Register 4. RF2 N-Divider Address Field = A[3:0] = 0100 Bit Name 24 D17 D16 D15 D14 D13 D12 D11 D10 0 D9 D8 D7 D6 NRF2[16:0] Bit Name Function 17 Reserved Program to 0. 16:0 NRF2[16:0] N-Divider for RF2 Synthesizer. Rev. 1.1 Si4133 Register 5. IF N-Divider Address Field (A[3:0]) = 0101 Bit D17 D16 D15 D14 D13 D12 D11 D10 Name 0 D9 0 D8 D7 D6 D5 D4 D3 D2 D1 D0 D4 D3 D2 D1 D0 D4 D3 D2 D1 D0 NIF[15:0] Bit Name 17:16 Reserved 15:0 NIF[15:0] Function Program to zero. N-Divider for IF Synthesizer. Register 6. RF1 R-Divider Address Field (A[3:0]) = 0110 Bit Name D17 D16 D15 D14 D13 D12 D11 D10 0 0 0 0 D9 D8 0 D7 D6 D5 RRF1[12:0] Name Function 17:13 Reserved Program to zero. 12:0 RRF1[12:0] R-Divider for RF1 Synthesizer. RRF1 can be any value from 7 to 8189 if KP1 = 00 8 to 8189 if KP1 = 01 10 to 8189 if KP1 = 10 14 to 8189 if KP1 = 11 Register 7. RF2 R-Divider Address Field (A[3:0]) = 0111 Bit Name D17 D16 D15 D14 D13 D12 D11 D10 0 0 0 0 D9 0 D8 D7 D6 D5 RRF2[12:0] Bit Name Function 17:13 Reserved Program to zero. 12:0 RRF2[12:0] R-Divider for RF2 Synthesizer. RRF2 can be any value from 7 to 8189 if KP2 = 00 8 to 8189 if KP2 = 01 10 to 8189 if KP2 = 10 14 to 8189 if KP2 = 11 Rev. 1.1 25 S i4 13 3 Register 8. IF R-Divider Address Field (A[3:0]) = 1000 Bit Name 26 D17 D16 D15 D14 D13 D12 D11 D10 0 0 0 Bit Name 17:13 Reserved 12:0 RIF[12:0] 0 D9 0 D8 D7 D6 D5 RIF[12:0] Function Program to zero. R-Divider for IF Synthesizer. RIF can be any value from 7 to 8189 if KP1 = 00 8 to 8189 if KP1 = 01 10 to 8189 if KP1 = 10 14 to 8189 if KP1 = 11 Rev. 1.1 D4 D3 D2 D1 D0 Si4133 Pin Descriptions: Si4133-BT SCLK 1 24 SENB SDA TA 2 23 V DDI GNDR 3 22 IFOUT RFLD 4 21 GNDI RFLC 5 20 IFLB GNDR 6 19 IFLA RFLB 7 18 GNDD RFLA 8 17 V DDD GNDR 9 16 GNDD GNDR 10 15 XIN RFOUT 11 14 PWDNB V DDR 12 13 A UXOUT Pin Number(s) Name Description 1 SCLK Serial clock input 2 SDATA Serial data input 3, 6, 9, 10 GNDR Common ground for RF analog circuitry 4, 5 RFLC, RFLD Pins for inductor connection to RF2 VCO 7, 8 RFLA, RFLB Pins for inductor connection to RF1 VCO 11 RFOUT Radio frequency (RF) output of the selected RF VCO 12 VDDR Supply voltage for the RF analog circuitry 13 AUXOUT Auxiliary output 14 PWDNB Power down input pin 15 XIN Reference frequency amplifier input 16, 18 GNDD Common ground for digital circuitry 17 VDDD Supply voltage for digital circuitry 19, 20 IFLA, IFLB Pins for inductor connection to IF VCO 21 GNDI Common ground for IF analog circuitry 22 IFOUT Intermediate frequency (IF) output of the IF VCO 23 VDDI Supply voltage for IF analog circuitry 24 SENB Enable serial port input Rev. 1.1 27 S i4 13 3 Table 13. Pin Descriptions for Si4133 Derivatives—TSSOP 28 Pin Number Si4133 Si4123 Si4122 Si4113 Si4112 1 SCLK SCLK SCLK SCLK SCLK 2 SDATA SDATA SDATA SDATA SDATA 3 GNDR GNDR GNDR GNDR GNDD 4 RFLD GNDR RFLD RFLD GNDD 5 RFLC GNDR RFLC RFLC GNDD 6 GNDR GNDR GNDR GNDR GNDD 7 RFLB RFLB GNDR RFLB GNDD 8 RFLA RFLA GNDR RFLA GNDD 9 GNDR GNDR GNDR GNDR GNDD 10 GNDR GNDR GNDR GNDR GNDD 11 RFOUT RFOUT RFOUT RFOUT GNDD 12 VDDR VDDR VDDR VDDR VDDD 13 AUXOUT AUXOUT AUXOUT AUXOUT AUXOUT 14 PWDNB PWDNB PWDNB PWDNB PWDNB 15 XIN XIN XIN XIN XIN 16 GNDD GNDD GNDD GNDD GNDD 17 VDDD VDDD VDDD VDDD VDDD 18 GNDD GNDD GNDD GNDD GNDD 19 IFLA IFLA IFLA GNDD IFLA 20 IFLB IFLB IFLB GNDD IFLB 21 GNDI GNDI GNDI GNDD GNDI 22 IFOUT IFOUT IFOUT GNDD IFOUT 23 VDDI VDDI VDDI VDDD VDDI 24 SENB SENB SENB SENB SENB Rev. 1.1 Si4133 GNDR SDA TA SCLK SENB V DDI IFOUT GNDI Pin Descriptions: Si4133-BM 28 27 26 25 24 23 22 IFLB RFLC 3 19 IFLA GNDR 4 18 GNDD RFLB 5 17 V DDD RFLA 6 16 GNDD GNDR 7 15 XIN 8 9 10 11 12 13 14 GNDD 20 PWDNB 2 A UXOUT RFLD V DDR GNDI RFOUT 21 GNDR 1 GNDR GNDR Pin Number(s) Name Description 1, 4, 7-9, 28 GNDR Common ground for RF analog circuitry 2, 3 RFLC, RFLD Pins for inductor connection to RF2 VCO 5,6 RFLA, RFLB Pins for inductor connection to RF1 VCO 10 RFOUT Radio frequency (RF) output of the selected RF VCO 11 VDDR Supply voltage for the RF analog circuitry 12 AUXOUT Auxiliary output 13 PWDNB Power down input pin 14, 16, 18 GNDD Common ground for digital circuitry 15 XIN Reference frequency amplifier input 17 VDDD Supply voltage for digital circuitry 19, 20 IFLA, IFLB Pins for inductor connection to IF VCO 21, 22 GNDI Common ground for IF analog circuitry 23 IFOUT Intermediate frequency (IF) output of the IF VCO 24 VDDI Supply voltage for IF analog circuitry 25 SENB Enable serial port input 26 SCLK Serial clock input 27 SDATA Serial data input Rev. 1.1 29 S i4 13 3 Table 14. Pin Descriptions for Si4133 Derivatives—MLP 30 Pin Number Si4133 Si4123 Si4122 Si4113 Si4112 1 GNDR GNDR GNDR GNDR GNDD 2 RFLD GNDR RFLD RFLD GNDD 3 RFLC GNDR RFLC RFLC GNDD 4 GNDR GNDR GNDR GNDR GNDD 5 RFLB RFLB GNDR RFLB GNDD 6 RFLA RFLA GNDR RFLA GNDD 7 GNDR GNDR GNDR GNDR GNDD 8 GNDR GNDR GNDR GNDR GNDD 9 GNDR GNDR GNDR GNDR GNDD 10 RFOUT RFOUT RFOUT RFOUT GNDD 11 VDDR VDDR VDDR VDDR VDDD 12 AUXOUT AUXOUT AUXOUT AUXOUT AUXOUT 13 PWDNB PWDNB PWDNB PWDNB PWDNB 14 GNDD GNDD GNDD GNDD GNDD 15 XIN XIN XIN XIN XIN 16 GNDD GNDD GNDD GNDD GNDD 17 VDDD VDDD VDDD VDDD VDDD 18 GNDD GNDD GNDD GNDD GNDD 19 IFLA IFLA IFLA GNDD IFLA 20 IFLB IFLB IFLB GNDD IFLB 21 GNDI GNDI GNDI GNDD GNDI 22 GNDI GNDI GNDI GNDD GNDI 23 IFOUT IFOUT IFOUT GNDD IFOUT 24 VDDI VDDI VDDI VDDD VDDI 25 SENB SENB SENB SENB SENB 26 SCLK SCLK SCLK SCLK SCLK 27 SDATA SDATA SDATA SDATA SDATA 28 GNDR GNDR GNDR GNDR GNDD Rev. 1.1 Si4133 Ordering Guide Ordering Part Number Description Operating Temperature Si4133-BM RF1/RF2/IF OUT –40 to 85oC Si4133-BT RF1/RF2/IF OUT –40 to 85oC Si4123-BM RF1/IF OUT –40 to 85oC Si4123-BT RF1/IF OUT –40 to 85oC Si4122-BM RF2/IF OUT –40 to 85oC Si4122-BT RF2/IF OUT –40 to 85oC Si4113-BM RF1 OUT –40 to 85oC Si4113-BT RF1 OUT –40 to 85oC Si4112-BM IF OUT –40 to 85oC Si4112-BT IF OUT –40 to 85oC Si4133 Derivative Devices The Si4133 performs both IF and dual-band RF frequency synthesis. The Si4112, Si4113, Si4122, and the Si4123 are derivatives of this device. Table 15 outlines which synthesizers each derivative device features as well as which pins and registers coincide with each synthesizer. Table 15. Si4133 Derivatives Name Synthesizer Pins Registers Si4112 IF IFLA, IFLB NIF, RIF, PDIB, IFDIV, LPWR, AUTOPDB = 0, PDRB = 0 Si4113 RF1, RF2 RFLA, RFLB, RFLC, RFLD NRF1, NRF2, RRF1, RRF2, PDRB, AUTOPDB = 0, PDIB = 0 Si4122 RF2, IF RFLC, RFLD, IFLA, IFLB NRF2, RRF2, PDRB, NIF, RIF, PDIB, IFDIV, LPWR Si4123 RF1, IF RFLA, RFLB, IFLA, IFLB NRF1, RRF1, PDRB, NIF, RIF, PDIB, IFDIV, LPWR Si4133 RF1, RF2, IF RFLA, RFLB, RFLC, RFLD, IFLA, IFLB NRF1, NRF2, RRF1, RRF2, PDRB, NIF, RIF, PDIB, IFDIV, LPWR Rev. 1.1 31 S i4 13 3 Package Outline: Si4133-BT θ2 S R1 E1 E R θ1 L L1 θ3 e D A2 c A b A1 Figure 19. 24-pin Thin Small Shrink Outline Package (TSSOP) Table 16. Package Diagram Dimensions Symbol A A1 A2 b c D e E E1 L L1 R R1 S θ1 θ2 θ3 32 Min — 0.05 0.80 0.19 0.09 7.70 4.30 0.45 0.09 0.09 0.20 0 Millimeters Nom 1.10 — 1.00 — — 7.80 0.65 BSC 6.40 BSC 4.40 0.60 1.00 REF — — — — 12 REF 12 REF Rev. 1.1 Max 1.20 0.15 1.05 0.30 0.20 7.90 4.50 0.75 — — — 8 Si4133 Package Outline: Si4133-BM Figure 20. 28-Pin Micro Leadframe Package (MLP) Table 17. Package Dimensions Controlling Dimension: mm Symbol Millimeters Min Nom Max A — 0.90 1.00 A1 0.00 0.01 0.05 b 0.18 0.23 0.30 D 5.00 BSC D1 4.75 BSC E 5.00 BSC E1 4.75 BSC N 28 Nd 7 Ne 7 e 0.50 BSC L 0.50 0.60 θ 0.75 12° Rev. 1.1 33 S i4 13 3 Contact Information Silicon Laboratories Inc. 4635 Boston Lane Austin, Texas 78735 Tel:1+ (512) 416-8500 Fax:1+ (512) 416-9669 Toll Free: 1+ (877) 444-3032 Email: [email protected] Internet: www.silabs.com The information in this document is believed to be accurate in all respects at the time of publication but is subject to change without notice. Silicon Laboratories assumes no responsibility for errors and omissions, and disclaims responsibility for any consequences resulting from the use of information included herein. Additionally, Silicon Laboratories assumes no responsibility for the functioning of undescribed features or parameters. Silicon Laboratories reserves the right to make changes without further notice. Silicon Laboratories makes no warranty, representation or guarantee regarding the suitability of its products for any particular purpose, nor does Silicon Laboratories assume any liability arising out of the application or use of any product or circuit, and specifically disclaims any and all liability, including without limitation consequential or incidental damages. Silicon Laboratories products are not designed, intended, or authorized for use in applications intended to support or sustain life, or for any other application in which the failure of the Silicon Laboratories product could create a situation where personal injury or death may occur. Should Buyer purchase or use Silicon Laboratories products for any such unintended or unauthorized application, Buyer shall indemnify and hold Silicon Laboratories harmless against all claims and damages. Silicon Laboratories and Silicon Labs are trademarks of Silicon Laboratories Inc. Other products or brandnames mentioned herein are trademarks or registered trademarks of their respective holders. 34 Rev. 1.1