Silicon RF Power Semiconductors ELECTROSTATIC SENSITIVE DEVICE OBSERVE HANDLING PRECAUTIONS RA55H4452M RoHS Compliance , 440-520MHz 55W 12.5V, 3 Stage Amp. For MOBILE RADIO DESCRIPTION The RA55H4452M is a 55-watt RF MOSFET Amplifier Module for 12.5-volt mobile radios that operate in the 440- to 520-MHz range. The battery can be connected directly to the drain of the enhancement-mode MOSFET transistors. Without the gate voltage (VGG=0V), only a small leakage current flows into the drain and the RF input signal attenuates up to 60 dB. The output power and drain current increase as the gate voltage increases. With a gate voltage around 4V (minimum), output power and drain current increases substantially. The nominal output power becomes available at 4.5V (typical) and 5V (maximum). At VGG=5V, the typical gate current is 1 mA. This module is designed for non-linear FM modulation, but may also be used for linear modulation by setting the drain quiescent current with the gate voltage and controlling the output power with the input power. FEATURES • Enhancement-Mode MOSFET Transistors (IDD≅0 @ VDD=12.5V, VGG=0V) BLOCK DIAGRAM 2 3 1 4 5 1 RF Input (Pin) 2 Gate Voltage (VGG), Power Control 3 Drain Voltage (VDD), Battery 4 RF Output (Pout) 5 RF Ground (Case) • Pout>55W, ηT>43% @ f=440-490MHz, PACKAGE CODE: H2S Pout>45W, ηT>35% @ f=491-520MHz, VDD=12.5V, VGG=5V, Pin=50mW • Broadband Frequency Range: 440-520MHz • Low-Power Control Current IGG=1mA (typ) at VGG=5V • Module Size: 66 x 21 x 9.88 mm • Linear operation is possible by setting the quiescent drain current with the gate voltage and controlling the output power with the input power RoHS COMPLIANCE • RA55H4452M-101 is a RoHS compliant products. • RoHS compliance is indicate by the letter “G” after the Lot Marking. • This product include the lead in the Glass of electronic parts and the lead in electronic Ceramic parts. However, it is applicable to the following exceptions of RoHS Directions. 1.Lead in the Glass of a cathode-ray tube, electronic parts, and fluorescent tubes. 2.Lead in electronic Ceramic parts. ORDERING INFORMATION: ORDER NUMBER SUPPLY FORM RA55H4452M-101 Antistatic tray, 10 modules/tray 25 Jun 2010 RA55H4452M 1/9 Silicon RF Power Semiconductors ELECTROSTATIC SENSITIVE DEVICE OBSERVE HANDLING PRECAUTIONS RA55H4452M RoHS COMPLIANCE MAXIMUM RATINGS (Tcase=+25°C, unless otherwise specified) SYMBOL PARAMETER VDD CONDITIONS Drain Voltage VGG<5V VGG Gate Voltage VDD<12.5V, Pin=0mW Pin Input Power Pout Output Power Tcase(OP) Tstg f=440-520MHz, ZG=ZL=50Ω RATING UNIT 17 V 6 V 100 MW 65 W Operation Case Temperature Range -30 to +110 °C Storage Temperature Range -40 to +110 °C Note.1.The above parameters are independently guaranteed. Note.2.In order to keep high reliability of the equipment, it is better to keep the module temperature of the module is recommended to keep lower than 90°C under all conditions, and to keep lower than 60°C under standard conditions. ELECTRICAL CHARACTERISTICS (Tcase=+25°C, ZG=ZL=50Ω, unless otherwise specified) SYMBOL PARAMETER f CONDITIONS Frequency Range Pout Output Power ηT Total Efficiency 2fo 2 ρin TYP MAX UNIT 440 - 520 MHz 55 @440-490MHz W 45 @491-520MHz 43 @440-490MHz VDD=12.5V,VGG=5V, Pin=50mW nd MIN Harmonic % 35 @491-520MHz - - -50 dBc Input VSWR - - 3:1 — IGG Gate Current - 1 - mA — Stability — Load VSWR Tolerance VDD=10.0-15.2V, Pin=25-70mW, Pout<65W (VGG control), Load VSWR=3:1 VDD=15.2V, Pin=50mW, Load VSWR=20:1 Pout=55W (VGG control)@440-490MHz Pout=45W (VGG control)@491-520MHz No parasitic oscillation — No degradation or destroy — Note. All parameters, conditions, ratings, and limits are subject to change without notice. 25 Jun 2010 RA55H4452M 2/9 Silicon RF Power Semiconductors ELECTROSTATIC SENSITIVE DEVICE OBSERVE HANDLING PRECAUTIONS RA55H4452M RoHS COMPLIANCE TYPICAL PERFORMANCE (Tcase=+25°C, ZG=ZL=50Ω, unless otherwise specified) rd OUTPUT POWER, TOTAL EFFICIENCY, and INPUT VSWR versus FREQUENCY 80 -30 60 ηT 50 50 40 40 V DD=12.5V V GG=5V Pin=50m W 20 10 ρ in 0 0 430 440 450 460 470 480 490 500 510 520 530 FREQUENCY f(MHz) -60 2nd -80 430 440 450 460 470 480 490 500 510 520 530 FREQUENCY f(MHz) OUTPUT POWER, POWER GAIN and DRAIN CURRENT versus INPUT POWER OUTPUT POWER, POWER GAIN and DRAIN CURRENT versus INPUT POWER 24 16 30 12 IDD 20 8 f=440MHz, V DD=12.5V, V GG=5V 10 4 0 out (dBm) 40 -5 0 5 10 INPUT POWER Pin(dBm) 15 8 IDD f=490MHz, V DD=12.5V, V GG=5V 4 0 out (dBm) 12 0 -5 10 15 4 6 8 10 12 DRAIN VOLTAGE V DD (V) 15 20 24 20 Gp 40 16 30 12 20 8 IDD f=520MHz, V DD=12.5V, V GG=5V 10 4 0 -10 -5 0 5 10 15 20 Pout 14 OUTPUT POWER P 24 22 20 18 16 14 12 10 8 6 4 2 0 out (W) OUTPUT POWER and DRAIN CURRENT versus DRAIN VOLTAGE DRAIN CURRENT I DD (A) out (W) OUTPUT POWER P 10 INPUT POWER Pin(dBm) IDD 2 5 0 20 OUTPUT POWER and DRAIN CURRENT versus DRAIN VOLTAGE f=440MHz, V GG=5V, Pin=50m W 0 Pout INPUT POWER Pin(dBm) 120 110 100 90 80 70 60 50 40 30 20 10 0 4 0 50 POWER GAIN Gp(dB) 30 OUTPUT POWER P 16 5 f=470MHz, V DD=12.5V, V GG=5V 60 DRAIN CURRENT I DD (A) POWER GAIN Gp(dB) out (dBm) 20 40 0 8 IDD OUTPUT POWER, POWER GAIN and DRAIN CURRENT versus INPUT POWER Gp -5 12 -10 24 -10 30 INPUT POWER Pin(dBm) Pout 10 16 0 20 60 20 20 40 10 OUTPUT POWER, POWER GAIN and DRAIN CURRENT versus INPUT POWER 50 Pout Gp 20 0 -10 24 50 POWER GAIN Gp(dB) 20 Gp 60 OUTPUT POWER P Pout DRAIN CURRENT I DD (A) POWER GAIN Gp(dB) OUTPUT POWER P out (dBm) 60 50 3rd -70 DRAIN CURRENT I DD (A) 20 30 -50 16 120 110 100 90 80 70 60 50 40 30 20 10 0 f=470MHz, V GG=5V, Pin=50m W 24 22 20 18 16 14 12 10 8 6 4 2 0 Pout IDD 2 4 6 8 10 12 DRAIN VOLTAGE VDD (V) 14 DRAIN CURRENT I DD (A) 30 -40 HARMONICS (dBc) 60 10 OUTPUT POWER P V DD=12.5V V GG=5V Pin=50m W 70 TOTAL EFFICIENCY η T(%) 70 INPUT VSWR ρ in (-) OUTPUT POWER P out (W) Pout DRAIN CURRENT IDD(A) 80 2nd, 3 HARMONICS versus FREQUENCY 16 25 Jun 2010 RA55H4452M 3/9 Silicon RF Power Semiconductors ELECTROSTATIC SENSITIVE DEVICE OBSERVE HANDLING PRECAUTIONS RA55H4452M RoHS COMPLIANCE TYPICAL PERFORMANCE (Tcase=+25°C, ZG=ZL=50Ω, unless otherwise specified) Pout IDD 6 8 10 12 DRAIN VOLTAGE VDD (V) 14 16 80 14 60 12 IDD 50 10 40 8 30 6 20 4 10 2 0 0 2.5 3 3.5 4 4.5 GATE VOLTAGE VGG(V) 5 out (W) Pout 90 16 OUTPUT POWER P 70 18 DRAIN CURRENT I DD (A) out (W) OUTPUT POWER P f=440MHz, V DD=12.5V, Pin=50m W 8 6 20 4 10 2 80 10 6 20 4 10 2 0 0 5 OUTPUT POWER P 12 out (W) 90 30 3.5 4 4.5 GATE VOLTAGE VGG(V) 10 30 16 8 3 12 IDD 40 18 40 2.5 16 14 50 0 2.5 14 IDD 50 18 Pout 3 3.5 4 4.5 GATE VOLTAGE VGG(V) 5 5.5 OUTPUT POWER and DRAIN CURRENT versus GATE VOLTAGE Pout 60 16 0 DRAIN CURRENT I DD (A) out (W) OUTPUT POWER P 70 14 60 5.5 90 f=490MHz, V DD=12.5V, Pin=50m W 6 8 10 12 DRAIN VOLTAGE VDD (V) f=470MHz, V DD=12.5V, Pin=50m W 70 OUTPUT POWER and DRAIN CURRENT versus GATE VOLTAGE 80 4 OUTPUT POWER and DRAIN CURRENT versus GATE VOLTAGE 90 80 Pout IDD 2 OUTPUT POWER and DRAIN CURRENT versus GATE VOLTAGE 24 22 20 18 16 14 12 10 8 6 4 2 0 DRAIN CURRENT I DD (A) 4 f=520MHz, V GG=5V, Pin=50m W 18 f=520MHz, V DD=12.5V, Pin=50m W 70 60 16 Pout 14 12 IDD 50 10 40 8 30 6 20 4 10 2 0 5.5 DRAIN CURRENT I DD (A) 2 120 110 100 90 80 70 60 50 40 30 20 10 0 DRAIN CURRENT I DD (A) 24 22 20 18 16 14 12 10 8 6 4 2 0 out (W) f=490MHz, V GG=5V, Pin=50m W OUTPUT POWER P 120 110 100 90 80 70 60 50 40 30 20 10 0 OUTPUT POWER and DRAIN CURRENT versus DRAIN VOLTAGE DRAIN CURRENT I DD (A) OUTPUT POWER P out (W) OUTPUT POWER and DRAIN CURRENT versus DRAIN VOLTAGE 0 2.5 3 3.5 4 4.5 GATE VOLTAGE VGG(V) 5 5.5 25 Jun 2010 RA55H4452M 4/9 Silicon RF Power Semiconductors ELECTROSTATIC SENSITIVE DEVICE OBSERVE HANDLING PRECAUTIONS RoHS COMPLIANCE RA55H4452M OUTLINE DRAWING (mm) 66.0 ±0.5 7.25 ±0.8 51.5 ±0.5 3 4 2.0 ±0.5 2 4.0 ±0.3 9.5 ±0.5 5 1 14.0 ±1 2-R2 ±0.5 17.0 ±0.5 60.0 ±0.5 21.0 ±0.5 3.0 ±0.3 Ø0.60 ±0.15 12.0 ±1 16.5 ±1 43.5 ±1 (9.88) 2.3 ±0.3 7.5 ±0.5 0.09 ±0.02 3.1 +0.6/-0.4 55.5 ±1 (50.4) 1 RF Input (Pin) 2 Gate Voltage (VGG) 3 Drain Voltage (VDD) 4 RF Output (Pout) 5 RF Ground (Case) 25 Jun 2010 RA55H4452M 5/9 Silicon RF Power Semiconductors ELECTROSTATIC SENSITIVE DEVICE OBSERVE HANDLING PRECAUTIONS RoHS COMPLIANCE RA55H4452M TEST BLOCK DIAGRAM Power Meter DUT 1 Signal Generator Attenuator Preamplifier Attenuator Directional Coupler 3 2 + DC Power Supply VGG Spectrum Analyzer 4 ZL=50Ω ZG=50Ω C1 5 Directional Coupler Attenuator Power Meter C2 + DC Power Supply VDD C1, C2: 4700pF, 22uF in parallel 1 RF Input (Pin) 2 Gate Voltage (VGG) 3 Drain Voltage (VDD) 4 RF Output (Pout) 5 RF Ground (Case) EQUIVALENT CIRCUIT 3 2 1 4 5 25 Jun 2010 RA55H4452M 6/9 Silicon RF Power Semiconductors ELECTROSTATIC SENSITIVE DEVICE OBSERVE HANDLING PRECAUTIONS RoHS COMPLIANCE RA55H4452M RECOMMENDATIONS and APPLICATION INFORMATION: Construction: This module consists of an alumina substrate soldered onto a copper flange. For mechanical protection, a plastic cap is attached with silicone. The MOSFET transistor chips are die bonded onto metal, wire bonded to the substrate, and coated with resin. Lines on the substrate (eventually inductors), chip capacitors, and resistors form the bias and matching circuits. Wire leads soldered onto the alumina substrate provide the DC and RF connection. Following conditions must be avoided: a) Bending forces on the alumina substrate (for example, by driving screws or from fast thermal changes) b) Mechanical stress on the wire leads (for example, by first soldering then driving screws or by thermal expansion) c) Defluxing solvents reacting with the resin coating on the MOSFET chips (for example, Trichloroethylene) d) Frequent on/off switching that causes thermal expansion of the resin e) ESD, surge, overvoltage in combination with load VSWR, and oscillation ESD: This MOSFET module is sensitive to ESD voltages down to 1000V. Appropriate ESD precautions are required. Mounting: Heat sink flatness must be less than 50 µm (a heat sink that is not flat or particles between module and heat sink may cause the ceramic substrate in the module to crack by bending forces, either immediately when driving screws or later when thermal expansion forces are added). A thermal compound between module and heat sink is recommended for low thermal contact resistance and to reduce the bending stress on the ceramic substrate caused by the temperature difference to the heat sink. The module must first be screwed to the heat sink, then the leads can be soldered to the printed circuit board. M3 screws are recommended with a tightening torque of 4.0 to 6.0 kgf-cm. Soldering and Defluxing: This module is designed for manual soldering. The leads must be soldered after the module is screwed onto the heat sink. The temperature of the lead (terminal) soldering should be lower than 350°C and shorter than 3 second. Ethyl Alcohol is recommend for removing flux. Trichloroethylene solvents must not be used (they may cause bubbles in the coating of the transistor chips which can lift off the bond wires). Thermal Design of the Heat Sink: At Pout=55W, VDD=12.5V and Pin=50mW each stage transistor operating conditions are: Pout Rth(ch-case) IDD @ ηT=35% VDD Pin Stage (W) (W) (V) (°C/W) (A) st 1 0.05 1.5 23.0 0.28 nd 12.5 2 1.5 13.0 2.4 3.30 rd 3 13.0 55.0 1.2 8.70 The channel temperatures of each stage transistor Tch = Tcase + (VDD x IDD - Pout + Pin) x Rth(ch-case) are: Tch1 = Tcase + (12.5V x 0.28 -1.5 + 0.05W) x 23.0°C/W = Tcase + 47.2 °C Tch2 = Tcase + (12.5V x 3.30A - 13.0W + 1.5W) x 2.4°C/W = Tcase + 71.4 °C Tch3 = Tcase + (12.5V x 8.70A - 55.0W + 13.0W) x 1.2°C/W = Tcase + 80.1 °C For long-term reliability, it is best to keep the module case temperature (Tcase) below 90°C. For an ambient temperature Tair=60°C and Pout=55W, the required thermal resistance Rth (case-air) = ( Tcase - Tair) / ( (Pout / ηT ) Pout + Pin ) of the heat sink, including the contact resistance, is: Rth(case-air) = (90°C - 60°C) / (55W/35% – 55W + 0.05W) = 0.29 °C/W When mounting the module with the thermal resistance of 0.29 °C/W, the channel temperature of each stage transistor is: Tch1 = Tair + 77.2 °C Tch2 = Tair + 101.4 °C Tch3 = Tair + 110.1 °C The 175°C maximum rating for the channel temperature ensures application under derated conditions. 25 Jun 2010 RA55H4452M 7/9 Silicon RF Power Semiconductors ELECTROSTATIC SENSITIVE DEVICE OBSERVE HANDLING PRECAUTIONS RoHS COMPLIANCE RA55H4452M Output Power Control: Depending on linearity, the following two methods are recommended to control the output power: a) Non-linear FM modulation: By the gate voltage (VGG). When the gate voltage is close to zero, the RF input signal is attenuated up to 60 dB and only a small leakage current flows from the battery into the drain. Around VGG=4V, the output power and drain current increases substantially. Around VGG=4.5V (typical) to VGG=5V (maximum), the nominal output power becomes available. b) Linear AM modulation: By RF input power Pin. The gate voltage is used to set the drain’s quiescent current for the required linearity. Oscillation: To test RF characteristics, this module is put on a fixture with two bias decoupling capacitors each on gate and drain, a 4.700 pF chip capacitor, located close to the module, and a 22 µF (or more) electrolytic capacitor. When an amplifier circuit around this module shows oscillation, the following may be checked: a) Do the bias decoupling capacitors have a low inductance pass to the case of the module? b) Is the load impedance ZL=50Ω? c) Is the source impedance ZG=50Ω? ATTENTION: 1.High Temperature; This product might have a heat generation while operation,Please take notice that have a possibility to receive a burn to touch the operating product directly or touch the product until cold after switch off. At the near the product,do not place the combustible material that have possibilities to arise the fire. 2. Generation of High Frequency Power; This product generate a high frequency power. Please take notice that do not leakage the unnecessary electric wave and use this products without cause damage for human and property per normal operation. 3. Before use; Before use the product,Please design the equipment in consideration of the risk for human and electric wave obstacle for equipment. PRECAUTION FOR THE USE OF MITSUBISHI SILICON RF POWER AMPLIFIER DEVICES: 1.The specifications of mention are not guarantee values in this data sheet. Please confirm additional details regarding operation of these products from the formal specification sheet. For copies of the formal specification sheets, please contact one of our sales offices. 2.RA series products (RF power amplifier modules) are designed for consumer mobile communication terminals and were not specifically designed for use in other applications. In particular, while these products are highly reliable for their designed purpose, they are not manufactured under a quality assurance testing protocol that is sufficient to guarantee the level of reliability typically deemed necessary for critical communications elements. Examples of critical communications elements would include transmitters for base station applications and fixed station applications that operate with long term continuous transmission and a higher on-off frequency during transmitting, especially for systems that may have a high impact to society. 3.RA series products use MOSFET semiconductor technology. They are sensitive to ESD voltage therefore appropriate ESD precautions are required. 4.In order to maximize reliability of the equipment, it is better to keep the devices temperature low. It is recommended to utilize a sufficient sized heat-sink in conjunction with other cooling methods as needed (fan, etc.) to keep the case temperature for RA series products lower than 60deg/C under standard conditions, and less than 90deg/C under extreme conditions. 5.RA series products are designed to operate into a nominal load impedance of 50 ohms. Under the condition of operating into a severe high load VSWR approaching an open or short, an over load condition could occur. In the worst case there is risk for burn out of the transistors and burning of other parts including the substrate in the module. 6.The formal specification includes a guarantee against parasitic oscillation under a specified maximum load mismatch condition. The inspection for parasitic oscillation is performed on a sample basis on our manufacturing line. It is recommended that verification of no parasitic oscillation be performed at the completed equipment level also. 7.For specific precautions regarding assembly of these products into the equipment, please refer to the supplementary items in the specification sheet. 8.Warranty for the product is void if the products protective cap (lid) is removed or if the product is modified in any way from it’s original form. 9.For additional “Safety first” in your circuit design and notes regarding the materials, please refer the last page of this data sheet. 10. Please refer to the additional precautions in the formal specification sheet. 25 Jun 2010 RA55H4452M 8/9 Silicon RF Power Semiconductors ELECTROSTATIC SENSITIVE DEVICE OBSERVE HANDLING PRECAUTIONS RoHS COMPLIANCE RA55H4452M Keep safety first in your circuit designs ! Mitsubishi Electric Corporation puts the maximum effort into making semiconductor products better and more reliable, but there is always the possibility that trouble may occur with them. Trouble with semiconductors may lead to personal injury, fire or property damage. Remember to give due consideration to safety when making your circuit designs, with appropriate measures such as (i) placement of substitutive, auxiliary circuits, (ii) use of non-flammable material or (iii) prevention against any malfunction or mishap. Notes regarding these materials These materials are intended as a reference to assist our customers in the selection of the Mitsubishi semiconductor product best suited to the customer’s application; they do not convey any license under any intellectual property rights, or any other rights, belonging to Mitsubishi Electric Corporation or a third party. - Mitsubishi Electric Corporation assumes no responsibility for any damage, or infringement of any third-party’s rights, originating in the use of any product data, diagrams, charts, programs, algorithms, or circuit application examples contained in these materials. - All information contained in these materials, including product data, diagrams, charts, programs and algorithms represents information on products at the time of publication of these materials, and are subject to change by Mitsubishi Electric Corporation without notice due to product improvements or other reasons. It is therefore recommended that customers contact Mitsubishi Electric Corporation or an authorized Mitsubishi Semiconductor product distributor for the latest product information before purchasing a product listed herein. The information described here may contain technical inaccuracies or typographical errors. Mitsubishi Electric Corporation assumes no responsibility for any damage, liability, or other loss rising from these inaccuracies or errors. Please also pay attention to information published by Mitsubishi Electric Corporation by various means, including the Mitsubishi Semiconductor home page (http://www.mitsubishichips.com). - When using any or all of the information contained in these materials, including product data, diagrams, charts, programs, and algorithms, please be sure to evaluate all information as a total system before making a final decision on the applicability of the information and products. Mitsubishi Electric Corporation assumes no responsibility for any damage, liability or other loss resulting from the information contained herein. - Mitsubishi Electric Corporation semiconductors are not designed or manufactured for use in a device or system that is used under circumstances in which human life is potentially at stake. Please contact Mitsubishi Electric Corporation or an authorized Mitsubishi Semiconductor product distributor when considering the use of a product contained herein for any specific purposes, such as apparatus or systems for transportation, vehicular, medical, aerospace, nuclear, or undersea repeater use. - The prior written approval of Mitsubishi Electric Corporation is necessary to reprint or reproduce in whole or in part these materials. - If these products or technologies are subject to the Japanese export control restrictions, they must be exported under a license from the Japanese government and cannot be imported into a country - 25 Jun 2010 RA55H4452M 9/9