NEW PRODUCT NEW PRODUCT NEW PRODUCT BYVB32-50 THRU BYVB32-200 FAST EFFICIENT PLASTIC RECTIFIER Reverse Voltage - 50 to 150 Volts Forward Current - 18.0 Amperes TO-263AB FEATURES 0.160 (4.06) 0.190 (4.83) 0.380 (9.65) 0.420 (10.67) 0.045 (1.14) 0.245 (6.22) MIN 0.055 (1.40) K 0.320 (8.13) 0.575 (14.60) 0.360 (9.14) 1 SEATING PLATE K 0.047 (1.19) 0.055 (1.40) 0.625 (15.88) 2 0.090 (2.29) 0.110 (2.79) -T- 0.018 (0.46) 0.095 (2.41) ♦ Plastic package has Underwriters Laboratory Flammability Classification 94V-0 ♦ Dual rectifier construction, positive centertap ♦ Glass passivated chip junctions ♦ Low power loss ♦ Low forward voltage, high current capability ♦ High surge capability ♦ Superfast recovery time for high efficiency ♦ High temperature soldering in accordance with CECC 802 / Reflow guaranteed 0.025 (0.64) 0.100 (2.54) 0.080 (2.03) 0.027 (0.686) MECHANICAL DATA 0.110 (2.79) 0.037 (0.940) Case: JEDEC TO-263AB molded plastic body Terminals: Plated leads solderable per MIL-STD-750, Method 2026 Polarity: As marked Mounting Position: Any Weight: 0.08 ounce, 2.24 grams PIN 1 K - HEATSINK PIN 2 Dimensions in inches and (millimeters) MAXIMUM RATINGS AND ELECTRICAL CHARACTERISTICS Ratings at 25°C ambient temperature unless otherwise specified. SYMBOLS BYVB32-50 BYVB32-100 BYVB32-150 BYVB32-200 UNITS Maximum repetitive peak reverse voltage VRRM 50 100 150 200 Volts Maximum RMS voltage VRMS 35 70 105 140 Volts VDC 50 100 150 200 Volts Maximum DC blocking voltage Maximum average forward rectified current at TC=120°C I(AV) 18.0 Amps Peak forward surge current 10ms single half sine-wave superimposed at at TJ=150°C IFSM 150.0 Amps VF 1.15 0.85 Volts IR 10.0 600.0 µA Maximum reverse recovery time per leg (NOTE 1) trr 35.0 ns Typical junction capacitance (NOTE 2) CJ 45.0 pF RΘJC 3.0 °C/W TJ, TSTG -65 to +150 °C Maximum instantaneous forward voltage per leg at: IF=20A, IF=5.0A, TJ=100°C Maximum DC reverse current at rated DC blocking voltage TJ=25°C TJ=100°C Maximum thermal resistance per leg (NOTE 3) Operating and storage temperature range NOTES: (1) Reverse recovery test conditions: IF=1A VR=30V, di/dt=100A/µs, Irr=10% IRM (2) Measured at 1.0 MHZ and applied reverse voltage of 4.0 Volts (3) Thermal resistance from junction to case per leg mounted on heatsink NOTICE: Advanced product information is subject to change without notice 4/98 RATINGS AND CHARACTERISTIC CURVES BYVB32-50 THRU BYVB32-200 FIG. 2 - MAXIMUM NON-REPETITIVE PEAK FORWARD SURGE CURRENT PER LEG 20 RESISTIVE OR INDUCTIVE LOAD 18 16 12 8.0 4.0 0 0 50 100 PEAK FORWARD SURGE CURRENT, AMPERES AVERAGE FORWARD CURRENT, AMPERES FIG.1 - FORWARD CURRENT DERATING CURVE 150 125 100 75 50 25 0 150 TJ=150°C 10ms SINGLE HALF SINE WAVE (JEDEC Method) 1 10 CASE TEMPERATURE, °C FIG. 4 - TYPICAL REVERSE CHARACTERISTICS PER LEG FIG. 3 - TYPICAL INSTANTANEOUS FORWARD CHARACTERISTICS PER LEG 1,000 TJ = 25°C PULSE WIDTH = 300µs 1% DUTY CYCLE 10 1 0.1 0.01 0.4 0.6 0.8 1.0 1.2 1.4 1.6 1.8 INSTANTANEOUS REVERSE LEAKAGE CURRENT, MICROAMPERES 100 INSTANTANEOUS FORWARD CURRENT, AMPERES 100 NUMBER OF CYCLES AT 50 HZ 100 TC=100°C 10 1 INSTANTANEOUS FORWARD VOLTAGE, VOLTS TC=25°C 0.1 FIG. 5 - TYPICAL JUNCTION CAPACITANCE PER LEG JUNCTION CAPACITANCE, pF 60 TJ=25°C f=1.0 MHZ Vsig=5mVp-p 50 40 30 20 10 0 1 10 REVERSE VOLTAGE, VOLTS 100 0 20 40 60 80 PERCENT OF RATED PEAK REVERSE VOLTAGE, % 100