STMICROELECTRONICS STPS30M100SFP

STPS30M100S
100 V, 30 A power Schottky rectifier
Features
A
■
Avalanche rated
■
Low VF
■
Good trade off between leakage current and
forward voltage drop
■
High frequency operation
■
Avalanche capability specified
K
A
K
Description
The STPS30M100S device is a single Schottky
rectifier, suited for high frequency switch mode
power supply.
Packaged in TO-220AB, TO-220FPAB, and I2PAK
this device is intended to be used in notebook and
game station adaptors, providing in these
applications a good efficiency at both low and
high load.
A
A
K
A
TO-220AB
STPS30M100ST
A
K
TO-220FPAB
STPS30M100SFP
Electrical characteristics (a)
Figure 1.
A
I
V
"Forward"
I
2 x IO
I2PAK
STPS30M100SR
IF
VRRM
VR
VAR
IO
K
A
X
X
Table 1.
V
Device summary
IR
IF(AV)
30 A
VTo VF(Io) VF VF(2xIo)
VRRM
100 V
Tj (max)
150 °C
VF(typ)
0.385 V
"Reverse"
IAR
a. VARM and IARM must respect the reverse safe
operating area defined in Figure 14. VAR and IAR are
pulse measurements (tp < 1 µs). VR, IR, VRRM and VF,
are static characteristics
January 2011
Doc ID 15523 Rev 3
1/10
www.st.com
10
Characteristics
1
STPS30M100S
Characteristics
Table 2.
Absolute ratings (limiting values)
Symbol
Parameter
Value
Unit
VRRM
Repetitive peak reverse voltage
100
V
IF(RMS)
Forward rms current
60
A
IF(AV)
Average forward current δ = 0.5
Tc = 125 °C
30
A
IFSM
Surge non repetitive forward current
tp = 10 ms sinusoidal
300
A
PARM
Repetitive peak avalanche power
tp = 1 µs Tj = 25 °C
tp < 1 µs Tj < 150 °C
IAR < 66 A
26400
W
120
V
120
V
-65 to + 175
°C
150
°C
Value
Unit
VARM (1)
Maximum repetitive peak avalanche
voltage
VASM (1)
Maximum single pulse peak avalanche tp < 1 µs Tj < 150 °C
voltage
IAR < 66 A
Storage temperature range
Tstg
Maximum operating junction temperature
Tj
(2)
1. Refer to Figure 14.
2.
dPtot
--------------dTj
1
- condition to avoid thermal runaway for a diode on its own heatsink
< ------------------------Rth ( j – a )
Table 3.
Thermal resistance
Symbol
Rth(j-c)
Table 4.
Symbol
Parameter
TO-220AB, I2PAK
1
TO-220FPAB
4
°C/W
Junction to case
Static electrical characteristics with all leads connected on board
Parameter
Test conditions
Tj = 25 °C
IR(1)
Reverse leakage current
Tj = 125 °C
Tj = 25 °C
Tj = 125 °C
Tj = 25 °C
Tj = 125 °C
Tj = 25 °C
VF(2)
Forward voltage drop
Tj = 125 °C
Tj = 25 °C
Tj = 125 °C
Tj = 25 °C
Tj = 125 °C
1. Pulse test: tp = 5 ms, δ < 2%
2. Pulse test: tp = 380 µs, δ < 2%
2/10
Doc ID 15523 Rev 3
VR = VRRM
VR = 70 V
IF = 5 A
IF = 10 A
Min.
Typ.
Max.
Unit
-
-
175
µA
-
20
50
mA
-
-
60
µA
-
10
20
mA
-
0.475
-
-
0.385
-
-
0.555
-
-
0.475
--
-
0.620
0.660
-
0.525
0.565
-
0.740
0.800
-
0.605
0.655
V
IF = 15 A
IF = 30 A
STPS30M100S
Characteristics
To evaluate the conduction losses use the following equation:
P = 0.475 x IF(AV) + 0.006 x IF2(RMS)
Figure 2.
Conduction losses versus average Figure 3.
current
PF (av)(W)
26
35
δ=0.05
24
δ=0.1
δ=0.2
δ=0.5
Average forward current versus
ambient temperature (δ = 0.5)
IF(av)(A)
δ=1
Rth(j-a)=Rth(j-c)
30
22
20
25
18
16
20
14
12
15
10
8
Rth(j-a)=15°C/W
10
T
6
T
4
5
2
δ=tp/T
IF(av)(A)
tp
δ=tp/T
0
4
8
Figure 4.
12
16
20
Tamb(°C)
tp
0
0
24
28
32
0
36
Normalized avalanche power
derating versus pulse duration
25
Figure 5.
PARM(tp)
PARM(1 µs)
50
75
100
125
150
Normalized avalanche power
derating versus junction
temperature
PARM(Tj)
PARM(25 °C)
1
1.2
1
0.1
0.8
0.6
0.4
0.01
0.2
Tj(°C)
tp(µs)
0.001
0.01
0.1
Figure 6.
350
1
0
10
100
1000
Non repetitive surge peak forward
current versus overload duration
(maximum values)
IM(A)
25
Figure 7.
1.0
T0-220AB / I2PAK
300
50
0.9
75
100
125
150
Relative variation of thermal
impedance junction to case versus
pulse duration
Zth(j-c)/Rth(j-c)
T0-220AB / I2PAK
0.8
250
0.7
0.6
200
150
Tc=25°C
0.5
Tc=75°C
0.4
0.3
100
Tc=125°C
50
IM
t(s)
δ=0.5
0
1.E-03
0.2
0.1
t
Single pulse
tp(s)
0.0
1.E-02
1.E-01
1.E+00
1.E-03
Doc ID 15523 Rev 3
1.E-02
1.E-01
1.E+00
3/10
Characteristics
Figure 8.
200
STPS30M100S
Non repetitive surge peak forward
current versus overload duration
(maximum values) (TO-220FPAB)
IM(A)
Figure 9.
1.0
Relative variation of thermal
impedance junction to case versus
pulse duration (TO-220FPAB)
Zth(j-c)/Rth(j-c)
0.9
0.8
150
0.7
0.6
100
0.5
Tc=25°C
0.4
Tc=75°C
0.3
50
IM
0.2
Tc=125°C
t(s)
t
δ =0.5
0.1
tp(s)
Single pulse
0
0.0
1.E-03
1.E-02
1.E-01
1.E+00
Figure 10. Reverse leakage current versus
reverse voltage applied (typical
values)
1.E+03
1.E-03
1.E-02
1.E-01
1.E+00
1.E+01
Figure 11. Junction capacitance versus
reverse voltage applied (typical
values)
IR(mA)
C(pF)
10000
F=1M H z
Vosc=30m V
Tj=25°C
1.E+02
Tj=150°C
1.E+01
Tj=125°C
Tj=100°C
1.E+00
Tj=75°C
1.E-01
1000
Tj=50°C
Tj=25°C
1.E-02
1.E-03
VR(V)
V R (V)
1.E-04
100
0
10
20
30
40
50
60
70
80
90
100
Figure 12. Forward voltage drop versus
forward current (high level)
200
1
10
100
Figure 13. Forward voltage drop versus
forward current (low level)
IFM(A)
30
IFM(A)
180
25
Tj=125°C
(Maximum values)
160
Tj=125°C
(Maximum values)
140
20
120
Tj=125°C
(Typical values)
100
15
Tj=125°C
(Typical values)
80
10
60
Tj=25°C
(Maximum values)
Tj=25°C
(Maximum values)
40
5
20
VFM(V)
VFM(V)
0
0
0.0
4/10
0.2
0.4
0.6
0.8
1.0
1.2
1.4
1.6
1.8
2.0
0.0
Doc ID 15523 Rev 3
0.2
0.4
0.6
0.8
1.0
STPS30M100S
Characteristics
Figure 14. Reverse safe operating area (tp < 1 µs and Tj < 150 °C)
80
IAR (A)
75
Forbid den area
Forbidden
70
65
60
Operating Area
55
50
100
VAR (V)
110
120
Doc ID 15523 Rev 3
130
140
150
5/10
Package Information
2
STPS30M100S
Package Information
●
Epoxy meets UL94,V0
●
Recommended torque: 0.4 to 0.6 N·m
In order to meet environmental requirements, ST offers these devices in different grades of
ECOPACK® packages, depending on their level of environmental compliance. ECOPACK®
specifications, grade definitions and product status are available at: www.st.com.
ECOPACK® is an ST trademark.
Table 5.
TO-220AB dimensions
Dimensions
Ref.
Dia
Min.
Max.
Min.
Max.
A
4.40
4.60
0.173
0.181
C
1.23
1.32
0.048
0.051
D
2.40
2.72
0.094
0.107
E
0.49
0.70
0.019
0.027
F
0.61
0.88
0.024
0.034
F1
1.14
1.70
0.044
0.066
F2
1.14
1.70
0.044
0.066
G
4.95
5.15
0.194
0.202
G1
2.40
2.70
0.094
0.106
H2
10
10.40
0.393
0.409
C
L5
L7
L6
L2
F2
D
L9
L4
L2
F
M
G1
Inches
A
H2
F1
Millimeters
16.4 typ.
0.645 typ.
L4
13
14
0.511
0.551
L5
2.65
2.95
0.104
0.116
L6
15.25
15.75
0.600
0.620
L7
6.20
6.60
0.244
0.259
L9
3.50
3.93
0.137
0.154
E
G
M
Diam.
6/10
Doc ID 15523 Rev 3
2.6 typ.
3.75
3.85
0.102 typ.
0.147
0.151
STPS30M100S
Package Information
Table 6.
TO-220FPAB dimensions
Dimensions
Ref.
A
B
H
Dia
L6
L2
L7
L3
L5
F1
L4
D
F
E
G1
G
Doc ID 15523 Rev 3
Inches
Min.
Max.
Min.
Max.
A
4.4
4.6
0.173
0.181
B
2.5
2.7
0.098
0.106
D
2.5
2.75
0.098
0.108
E
0.45
0.70
0.018
0.027
F
0.75
1
0.030
0.039
F1
1.15
1.70
0.045
0.067
F2
1.15
1.70
0.045
0.067
G
4.95
5.20
0.195
0.205
G1
2.4
2.7
0.094
0.106
H
10
10.4
0.393
0.409
L2
F2
Millimeters
16 Typ.
0.63 Typ.
L3
28.6
30.6
1.126
1.205
L4
9.8
10.6
0.386
0.417
L5
2.9
3.6
0.114
0.142
L6
15.9
16.4
0.626
0.646
L7
9.00
9.30
0.354
0.366
Dia.
3.00
3.20
0.118
0.126
7/10
Package Information
STPS30M100S
Devices in I2PAK with nickel-plated back frame must NOT be mounted by frame soldering
like SMDs. Such devices are intended to be through-hole mounted ONLY and in no
circumstances shall ST be held liable for any lack of performance or damage arising out of
soldering of nickel-plated back frames.
Table 7.
I2PAK dimensions
Dimensions
Ref.
Millimeters
Inches
Min.
Max.
Min.
Max.
A
4.40
4.60
0.173
0.181
A1
2.40
2.72
0.094
0.107
b
0.61
0.88
0.024
0.035
b1
1.14
1.70
0.044
0.067
c
0.49
0.70
0.019
0.028
c2
1.23
1.32
0.048
0.052
D
8.95
9.35
0.352
0.368
e
2.40
2.70
0.094
0.106
e1
4.95
5.15
0.195
0.203
E
10
10.40
0.394
0.409
L
13
14
0.512
0.551
L1
3.50
3.93
0.138
0.155
L2
1.27
1.40
0.050
0.055
A
E
c2
L2
D
L1
A1
b1
L
b
c
e
e1
8/10
Doc ID 15523 Rev 3
STPS30M100S
3
Ordering information
Ordering information
Table 8.
Ordering information
Order code
Marking
Package
Weight
Base qty
Delivery mode
STPS30M100ST
STPS30M100ST
TO-220AB
2.3 g
50
Tube
STPS30M100SFP
STPS30M100SFP
TO-220FPAB
2.0 g
50
Tube
1.49 g
50
Tube
STPS30M100SR
4
STPS30M100SR
2
I PAK
Revision history
Table 9.
Document revision history
Date
Revision
Changes
25-Mar-2009
1
First issue
15-Apr-2010
2
Updated package graphic on front page. Updated Table 3, Table 5,
Table 6, and Table 7.
28-Jan-2011
3
Added warning paragraph above Table 7.
Doc ID 15523 Rev 3
9/10
STPS30M100S
Please Read Carefully:
Information in this document is provided solely in connection with ST products. STMicroelectronics NV and its subsidiaries (“ST”) reserve the
right to make changes, corrections, modifications or improvements, to this document, and the products and services described herein at any
time, without notice.
All ST products are sold pursuant to ST’s terms and conditions of sale.
Purchasers are solely responsible for the choice, selection and use of the ST products and services described herein, and ST assumes no
liability whatsoever relating to the choice, selection or use of the ST products and services described herein.
No license, express or implied, by estoppel or otherwise, to any intellectual property rights is granted under this document. If any part of this
document refers to any third party products or services it shall not be deemed a license grant by ST for the use of such third party products
or services, or any intellectual property contained therein or considered as a warranty covering the use in any manner whatsoever of such
third party products or services or any intellectual property contained therein.
UNLESS OTHERWISE SET FORTH IN ST’S TERMS AND CONDITIONS OF SALE ST DISCLAIMS ANY EXPRESS OR IMPLIED
WARRANTY WITH RESPECT TO THE USE AND/OR SALE OF ST PRODUCTS INCLUDING WITHOUT LIMITATION IMPLIED
WARRANTIES OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE (AND THEIR EQUIVALENTS UNDER THE LAWS
OF ANY JURISDICTION), OR INFRINGEMENT OF ANY PATENT, COPYRIGHT OR OTHER INTELLECTUAL PROPERTY RIGHT.
UNLESS EXPRESSLY APPROVED IN WRITING BY AN AUTHORIZED ST REPRESENTATIVE, ST PRODUCTS ARE NOT
RECOMMENDED, AUTHORIZED OR WARRANTED FOR USE IN MILITARY, AIR CRAFT, SPACE, LIFE SAVING, OR LIFE SUSTAINING
APPLICATIONS, NOR IN PRODUCTS OR SYSTEMS WHERE FAILURE OR MALFUNCTION MAY RESULT IN PERSONAL INJURY,
DEATH, OR SEVERE PROPERTY OR ENVIRONMENTAL DAMAGE. ST PRODUCTS WHICH ARE NOT SPECIFIED AS "AUTOMOTIVE
GRADE" MAY ONLY BE USED IN AUTOMOTIVE APPLICATIONS AT USER’S OWN RISK.
Resale of ST products with provisions different from the statements and/or technical features set forth in this document shall immediately void
any warranty granted by ST for the ST product or service described herein and shall not create or extend in any manner whatsoever, any
liability of ST.
ST and the ST logo are trademarks or registered trademarks of ST in various countries.
Information in this document supersedes and replaces all information previously supplied.
The ST logo is a registered trademark of STMicroelectronics. All other names are the property of their respective owners.
© 2011 STMicroelectronics - All rights reserved
STMicroelectronics group of companies
Australia - Belgium - Brazil - Canada - China - Czech Republic - Finland - France - Germany - Hong Kong - India - Israel - Italy - Japan Malaysia - Malta - Morocco - Philippines - Singapore - Spain - Sweden - Switzerland - United Kingdom - United States of America
www.st.com
10/10
Doc ID 15523 Rev 3