CRYSTEKCRYSTAL IB1215LT-1W

IB_LT-1W Series
1W, FIXED INPUT, ISOLATED & REGULATED
SINGLE OUTPUT SMD DC-DC CONVERTER
RoHS
FEATURES
● Small Footprint
● SMD Package
● 1kVDC Isolation
● Temperature Range: -40°C ~ +85°C
● Internal SMD Construction
● Short Circuit Protection
● No Heatsink Required
● No External Component Required
● Industry Standard Pinout
● RoHS Compliance
PRODUCT PROGRAM
Input
Part
Number
Output
Voltage (VDC)
Efficiency
(%, Typ.)
Current (mA)
Voltage
(VDC)
Max.
Min.
IB0505LT-W75
5
150
15
69
IB0509LT-1W
9
111
12
70
Nominal
5
Range
4.75-5.25
IB0512LT-1W
12
83
9
71
IB0515LT-1W
15
67
7
72
IB1205LT-W75
5
150
15
69
IB1212LT-1W
12
11.4-12.6
12
83
9
71
IB1215LT-1W
15
67
7
72
IB1505LT-W75 *
5
150
15
69
IB1509LT-1W *
9
111
12
70
IB1512LT-1W *
12
83
9
71
IB1515LT-1W
15
67
7
72
are isolated from the input power supply in a
IB2405LT-W75
5
150
15
69
distributed power supply system on a circuit board.
IB2409LT-1W *
9
111
12
70
IB2412LT-1W
12
83
9
71
IB2415LT-1W
15
67
7
72
APPLICATIONS
The IB_LT-1W series are specially designed for
applications where a group of polar power supplies
These products apply to:
1) Where the voltage of the input power supply
is fixed (voltage variation ≤ ±5%);
2) Where isolation is necessary between input
15
24
14.25-15.75
22.8-25.2
*Designing
and output (isolation voltage ≤1000VDC);
3) Where the regulation of the output voltage and
the output ripple noise are not demanding.
COMMON SPECIFICATIONS
Item
Test Conditions
Min.
Typ.
Storage humidity
MODEL SELECTION
Rated Power
Package Style
Ou tput Voltage
Input Voltage
Produc t Ser ies
Units
95
%
Operating temperature
-40
85
Storage temperature
-55
125
Temp. rise at full load
Lead temperature
IB0512LT-1W
Max.
15
1.5mm from case for 10 seconds
°C
25
260
Cooling
Free air convection
Short circuit protection
Continuous
Package material
Epoxy Resin (UL94-V0)
MTBF
3500
Weight
k hours
2.9
g
ISOLATION SPECIFICATIONS
MORNSUN Science & Technology Co.,Ltd.
Address: No. 5, Kehui St. 1, Kehui development
center, Science Ave., Guangzhou Science City,
Luogang district, Guangzhou,P.R.China.
Tel: 86-20-28203030
Fax:86-20-38601272
Http://www.mornsun-power.com
Item
Test Conditions
Isolation voltage
Tested for 1 minute and 1mA max 1000
Isolation resistance
Test at 500VDC
Isolation capacitance
The copyright and authority for the interpretation of the products are reserved by MORNSUN
Min.
Typ.
Max.
Units
VDC
1000
MΩ
70
pF
Specifications subject to change without notice.
IB_LT-1W
B/1-2010
Page 1 of 3
OUTPUT SPECIFICATIONS
Item
TYPICAL CHARACTERISTICS
Test Conditions
Min.
Output power
Typ.
Max.
Units
1
W
0.1
Line regulation
For Vin change of ±5%
Load regulation
10% to 100% load
±0.3
±1
%
±3
Output voltage accuracy 100% full load
±0.03
Temperature drift
100% full load
Ripple*
20MHz Bandwidth
10
20
Noise*
20MHz Bandwidth
50
150
Switching frequency
Full load, nominal input
100
%/°C
mVp-p
kHz
*Test ripple and noise by “parallel cable” method. See detailed operation instructions at Testing of Power
Converter section, application notes.
RECOMMENDED REFLOW SOLDERING PROFILE
RECOMMENDED CIRCUIT
Pea k. Temp 26 0 C
1 0 Se c Ma x
2 20 C
2 50
Te mperatu re ( C )
Operating Temp.(oC)
2 00
L
L
+Vo
Vin
DC DC
Cin
1 50
90 Sec M ax
(>22 0 C )
1 00
Cout
GND
0V
(Figure 1)
50
0
Time (s ec .)
Vin
APPLICATION NOTE
+Vo
REG
DC DC
GND
0V
1) Requirement on output load
To ensure this module can operate efficiently and reliably, During operation, the minimum
(Figure 2)
output load could not be less than 10% of the full load. If the actual output power is very
small, please connect a resistor with proper resistance at the output end in parallel to
increase the load
EXTERNAL CAPACITOR TABLE (TABLE 1)
Vin
(VDC)
5
Cin
(µF)
4.7
Single Vout
(VDC)
5
Cout
(µF)
4.7
12
2.2
9
2.2
It should also be noted that the inductance and the frequency of the “LC” filtering network
15
1
12
2.2
should be staggered with the DC/DC frequency to avoid mutual interference. However, the
24
1
15
1
2) Recommended circuit
If you want to further decrease the input/output ripple, an “LC” filtering network may be
connected to the input and output ends of the DC/DC converter, see (Figure 1).
capacitance of the output filter capacitor must be proper. If the capacitance is too big, a
startup problem might arise. For every channel of output, provided the safe and reliable
operation is ensured, the greatest capacitance of its filter capacitor sees (Table 1).
It’s not recommended to connect any external
capacitor in the application field with less than 0.5
watt output.
3) Overload Protection
Under normal operating conditions, the output circuit of these products has no protection
against over-current. The simplest method is to connect a self-recovery fuse in series at the
input end or add a circuit breaker to the circuit.
4) Input Over-voltage Protection Circuit
The simplest device for input over-voltage protection is a linear voltage regulator with
overheat protection that is connected to the input end in series (Figure 2).
5) No parallel connection or plug and play
The copyright and authority for the interpretation of the products are reserved by MORNSUN
Specifications subject to change without notice.
IB_LT-1W
B/1-2010
Page 2 of 3
OUTLINE DIMENSIONS & PIN CONNECTIONS
MECHANICAL DIMENSIONS
RECOMMENDED FOOTPRINT
( Side V ie w )
5.75 [0.226]
6.00 [0.236]
17.78 [0.700]
9
8
( To p View )
1 2
3
5
6
7
0.60 [0.024]
14 13 1 2
16.70 [0.657]
10
12.70 [0.500]
14 13 1 2
17.78 [0.700]
15.24 [0.600]
10 9
8
2.54 [0.100]
1
2
3
5
6
7
2.10 [0.083]
1.00 [0.039]
2.54 [0.100]
2.54 [0.100]
F OOTPR I N T D ETAILS
Func t ion
Pin
A
12.22 [0.481]
1
2
6
0.25 [0.010]
A
GN D
Vin
7
Others
5 max
Note:
1.30 [0.051]
Unit: mm[inch]
Pin section tolerances: 0.10mm[ 0.004inch]
General tolerances: 0.25mm[ 0.010inch]
0V
+Vo
NC
N C :N o C onnec t ion
REEL PACKING OUTLINE DIMENSIONS
TUBE OUTLINE DIMENSIONS
Taping dimension:
2.00 [0.079]
4.00 [0.157]
∅1.50[0.059]
1.75 [0.069]
14.20[0.559]
18.00[0.709]
18.20[0.717]
21.20 [0.835]
14.00 [0.551]
0.50[0.020]
32.00 [0.260]
∅1.50[0.059]
7.10 [0.280]
6.80[0.268]
7.30 [0.287]
24.00[0.945]
8.60 [0.339]
Note:
Unit: mm[inch]
General tolerances:
Taping reel dimension:
37.40 [1.472]
∅100.00 [3.937]
0.5mm[ 0.020inch]
L=530mm[20.866inch] Devices per tube quantity : 28pcs
L=220mm[8.661inch] Devices per tube quantity : 10pcs
∅330.00 [12.992]
0.60 [0.024]
∅13.00 [0.512]
∅21.50 [0.846]
Note:
Unit: mm[inch]
General tolerances: 0.5mm[ 0.020inch]
Devices per reel quantity: 400pcs
Note:
1. Operation under minimum load will not damage the converter; However, they may not meet all specification listed, and that will reduce the life
of product.
2. All specifications measured at Ta=25°C, humidity<75%, nominal input voltage and rated output load unless otherwise specified.
3. Only typical models listed, other models may be different, please contact our technical person for more details.
4. In this datasheet, all the test methods of indications are based on corporate standards.
The copyright and authority for the interpretation of the products are reserved by MORNSUN
Specifications subject to change without notice.
IB_LT-1W
B/1-2010
Page 3 of 3