General Purpose Relays Power Relays Potter & Brumfield T9A Series, DC Coil 30A PCB or Panel Mount Relay n 30A switching in 1 form A (NO) and 20A in 1 form C (CO) Plastic sealed case available n Meets UL 508 and 873 spacing - 3.18mm through air, 6.36mm over surface n Option for load connections via 0.250”” (6.35mm) Q.C. terminals n UL class F insulation system standard n Typical applications HVAC, Appliances, Industrial Controls Approvals UL E58304; CSA LR48471 Technical data of approved types on request Contact Data Contact arrangement 1 form A (NO), 1 form B (NC), 1 form C (CO) Rated voltage 277VAC Max. switching voltage 277VAC Rated current 30A 15A 20A/10A Limiting continuous current 30A Contact material AgSnOInO, AgCdO Min. recommended contact load 1A, 5VDC or 12VAC Initial contact resistance 75 mΩ at 1A at 5VDC or 12VAC Frequency of operation, with/without load 360/3600hr Operate/release time max., including bounce 15/15ms Contact ratings 1) TypeLoad Factory AgCdO, 1W coil NO 30A, 240VAC, general purpose NO 25A, 240VAC, resistive CO 20A/10A, 240VAC, general purpose CO 20A/10A, 240VAC, resistive CO 20A/10A, 28VDC, resistive UL 508/873 AgCdO, 1W coil NO 30A, 240VAC, general purpose NC 15A, 240VAC, general purpose CO 20A/10A, 240VAC, general purpose NO 25A, 240VAC, resistive NC 20A, 240VAC, resistive CO 16.75A/13.4A, 240VAC, resistive NO 80LRA/30FLA, 240VAC NC 30LRA/12FLA, 240VAC CO 53.6LRA/20FLA / 20LRA/8FLA, 240VAC NO 98LRA/22FLA, 120VAC NO 2HP, 240VAC NC 1/2HP, 240VAC NO 1HP, 125VAC NC 1/4HP, 125VAC NO 10A, 277VAC, ballast NC 3A, 277VAC, ballast NO 8.3A, 120VAC, tungsten NO 5.4A, 277VAC, tungsten NO 470VA, 120VAC, pilot duty NO 20A, 28VDC, resistive NC 10A, 28VDC, resistive AgCdO - Enhanced Version Only, 1W coil NO 21A, 250VAC, resistive NO 25A, 277VAC, resistive Cycles 100x103 100x103 100x103 100x103 100x103 100x103 100x103 100x103 6x103 6x103 6x103 30x103 30x103 30x103 100x103 1x103 1x103 1x103 1x103 6x103 6x103 6x103 6x103 30x103 100x103 100x103 250x103 100x103 Contact ratings 1) (continued) TypeLoad UL 508/873 AgSnOInO, 1W coil NO 30A, 240VAC, general purpose NO 80LRA/30FLA, 240VAC NC 10A, 250VAC, resistive AgCdO, 900mW coil NO 30A, 240VAC, general purpose NO 18A, 240VAC, resistive, 105°C NC 15A, 240VAC, resistive NO 30LRA/15FLA, 240VAC NO 50LRA/16FLA, 120VAC NO 30LRA/11FLA, 120VAC Cycles 100x103 30x103 50x103 100x103 100x103 6x103 100x103 100x103 200x103 1) Contact ratings at 25°C (unless otherwise noteed) with relay properly vented. Remove vent nib after soldering and cleaning. Mechanical endurance 10x106 ops. Coil Data Coil voltage range 5 to 110VDC Max. coil power 110% of nominal Max. coil temperature 155°C Coil insulation system according UL Class F Coil versions, DC coil Coil Rated Operate Release Coil Rated coil codevoltagevoltagevoltage resistancepower VDCVDCVDC Ω±10%W Code D (1W) coil 5 53.75 0.5 251 6 6 4.50.636 1 9 96.75 0.9 811 12129 1.2 1441 15 1511.251.5225 1 18 1813.5 1.8324 1 24 2418 2.4576 1 48 48 36 4.8 2304 1 11011082.511 12100 1 Code L (900W) coil 5 5 3.75 0.5 27 .9 6 6 4.50.640 .9 9 9 6.75 0.9 97 .9 12 12 9 1.2 155 .9 15 1511.251.5256 .9 18 1813.5 1.8380 .9 24 2418 2.4660 .9 48 48 36 4.8 2560 .9 11011082.511 13450 .9 All figures are given for coil without preenergization, at ambient temperature +23°C. 1) Contact ratings at 25°C (unless otherwise noted) with relay properly vented. Remove vent nib after soldering and cleaning. 08-2012, Rev. 0812 www.te.com © 2012 Tyco Electronics Corporation, a TE Connectivity Ltd. company Datasheets and product specification according to IEC 61810-1 and to be used only together with the ‘Definitions’ section. Datasheets and product data is subject to the terms of the disclaimer and all chapters of the ‘Definitions’ section, available at http://relays.te.com/definitions Datasheets, product data, ‘Definitions’ section, application notes and all specifications are subject to change. 1 General Purpose Relays Power Relays Potter & Brumfield T9A Series, DC Coil 30A PCB or Panel Mount Relay (Continued) Coil Data (continued) Ambient temperature vs. coil voltage – 1W coil Data below are average values and should be verified in application. Tests were conducted within a 2’ (.6 m) cube (still air); at nominal coil power @ 25°C; with normally open contact loaded; and with 4’ (1.22 m) long, #10 AWG load wires. P.C. board relays were mounted to a 30A, single side P.C. board. Coil rise test conducted with a 30A PC board to maintain 20°C max. rize at 30°C. The relay connections and wiring must be designed with an adequate cross section to ensure proper current flow and heat dissipation. 140 Max. Alowable Ambient Temp. (C) 120 Initial dielectric strength between open contacts 1500Vrms between contact and coil 2500Vrms Initial surge withstand voltage between contact and coil 6kV Initial insulation resistance between insulated elements 1x109Ω Clearance/creepage between contact and coil3.18mm clearance/6.3638mm Other Data 100 80 0A 10A 20A 60 40 20 0 60 Wash-Tight Relay, Vented (2, Load Connections Via Q.C. Terminals, PC Mount 80 30A 100 120 140 Applied Coil Voltage (% of Rated Voltage) 160 180 140 Max. Alowable Ambient Temp. (C) Insulation Data 120 100 0A 10A 20A 80 60 40 60 Dust Protected Relay, Flange Mount 80 30A 100 120 140 Applied Coil Voltage (% of Rated Voltage) 160 180 Material compliance: EU RoHS/ELV, China RoHS, REACH, Halogen content refer to the Product Compliance Support Center at www.te.com/customersupport/rohssupportcenter Ambient temperature DC coil -55ºC to 85ºC 3) 105°C models available Category of environmental protection IEC 61810RT0 - open, RTI - dust protected, RTII - flux proof, RTIII - wash tight Vibration resistance (functional) 1.65mm max excursions, 10-55 Hz Shock resistance (functional) 10g for 11msec Shock resistance (destructive) 100g Terminal typepcb-tht and pcb-tht + quick connect Weight 26g mounting code 1 33g mounting codes 2 and 5 Resistance to soldering heat THT IEC 60068-2-20 250°C Packaging/unit tray/50 pcs., bundle/250 pcs., box/500 pcs. 3) Operating ambient temperature must consider “Must Operate Voltage Change Over Temperature,” Contact Temperature Rise, Coil Temperature Rise (If coil is not allowed to cool) and Maximum Coil Temperature. Specification ambient considers 20A load with coil cooled to ambient. 140 Max. Alowable Ambient Temp. (C) 120 100 80 60 0A 10A 20A 40 Wash-Tight Relay, Vented (2 PC Terminals For Coil & Contacts 20 0 60 80 30A 100 120 140 Applied Coil Voltage (% of Rated Voltage) 160 180 2) Remove knock-off nib after cleaning process for optimum life of wash-tight relays. Dimensions .045 x .045 (1.14 x 1.14) 1.280 MAX. (32.51) NO COM Ø .03 (.80) 2 PLACES NC .032 x .062 (.81 x 1.57) 1.080 MAX. (27.43) 1.100 MAX. (27.94) .187 x .020 (4.75 x .508) QUICK CONNECT 1.080 MAX. (27.43) 1.100 MAX. (27.94) .250 x .032 (6.35 x .81) QUICK CONNECT 1.980 MAX. (50.29) COM .130 .020 (3.30 .51) NO .250 x .032 QUICK (6.35 x .81) CONNECT T9AP – Mounting and termination code 5 1.713 ± .010 (43.51 ± .25) 1.280 MAX. (32.51) NC T9AS – Mounting and termination code 2 .071 (1.80) RAD. FOR #6 SCREW Note: Recommended mounting screw torque is 4.0-5.0 lbs.in when #6 screw is used. 2 08-2012, Rev. 0812 www.te.com © 2012 Tyco Electronics Corporation, a TE Connectivity Ltd. company Datasheets and product specification according to IEC 61810-1 and to be used only together with the ‘Definitions’ section. Datasheets and product data is subject to the terms of the disclaimer and all chapters of the ‘Definitions’ section, available at http://relays.te.com/definitions Datasheets, product data, ‘Definitions’ section, application notes and all specifications are subject to change. General Purpose Relays Power Relays Potter & Brumfield T9A Series, DC Coil 30A PCB or Panel Mount Relay (Continued) Dimensions Plain case Bracket mount case .805 MAX. (20.4) .212 MAX. (5.38) .130 + .016 – .010 3.30 + .41 –.25 ( ) .680 MAX. (17.27) .950 MAX. (24.13) .032 x .062 (.8 x 1.6) TERMINALS .130 ± .020 (3.3 ± .51) .10 MAX. (2.54) .50 (12.8) .69 (17.6) .032 x .062 (.8 x 1.6) TERMINALS 1.280 MAX. (32.51) Ø .03 (.80) TERMINALS .016 (.43) 1.08 MAX. (27.43) .045 x .045 (1.14 x 1.14) TERMINAL 1.20 MAX. (30.5) .045 x .045 (1.14 x 1.14) TERMINAL Ø .03 (0.80) TERMINALS Terminal assignment Bottom view on pins 1 Form A 1 Form B 1 Form C PCB layout Bottom view on pins T9AP/S - Mounting and termination code 2 .140 MAX. (3.56) .250 MAX. (6.35) .300 .100 (7.62) (2.54) .150 (3.81) .212 MAX. (5.38) .081 ± .005 DIA. (2.06 ± .13) .078 ± .003 DIA. (1.98 ± .08) .600 (15.24) .500 (12.7) T9AS/V - Mounting and termination code 1 .043 ± .003 DIA. (1.09 ± .08) .300 (7.62) Only necessary terminals are present on single throw models. Consequently, some holes will be unnecessary for single throw models. .150 (3.81) .550 (13.97) Typical product code .081 ± .005 DIA. (2.06 ± .13) .078 ± .003 DIA. (1.98 ± .08) .600 (15.24) .500 (12.7) .550 (13.97) .700 (17.78) Product code structure .100 (2.54) .043 ± .003 DIA. (1.09 ± .08) Only necessary terminals are present on single throw models. Consequently, some holes will be unnecessary for single throw models. .700 (17.78) T9A S5D22-12 Type T9A Power PCB or panel mount relay T9A Enclosure N Open, no enclosure (requires mounting code 1) P Dust protected plastic case (requires mounting code 5) S Wash-tight plastic case with knock off nib (requires mounting code 1 or 2) V Flux-proof plastic case (requires mounting code 1 or 2) Contact arrangement 1 1 form A (1 NO) 2 1 form B (1 NC) 5 1 form C (1 CO) Coil Input D DC voltage, 1W L DC voltage, 900mW Mounting and termination 1 PCB mounting; PCB terminals for coil and contacts (only available with enclosure code N, S or V) 2 PCB mounting; PCB term. for coil and contacts; 6.35mm (.250in) QC for contacts (only available with enclosure code S or V) 5 Flanged mounting; 4.75mm (.187) QC for coil; 6.35mm (.250in) QC for contacts (only available with enclosure code P) Contact material 2 AgCdO 4 AgSnOInO 7 AgCdO (Enhanced version) Coil voltage Coil code: please refer to coil versions table 08-2012, Rev. 0812 www.te.com © 2012 Tyco Electronics Corporation, a TE Connectivity Ltd. company Datasheets and product specification according to IEC 61810-1 and to be used only together with the ‘Definitions’ section. Datasheets and product data is subject to the terms of the disclaimer and all chapters of the ‘Definitions’ section, available at http://relays.te.com/definitions Datasheets, product data, ‘Definitions’ section, application notes and all specifications are subject to change. 3 General Purpose Relays Power Relays Potter & Brumfield T9A Series, DC Coil 30A PCB or Panel Mount Relay (Continued) 4 Product Code Enclosure Contacts Coil Mounting Contact Material Coil Part Number T9AN1L22-24 T9AN5L12-24 T9AN5L22-24 T9AP1D52-12 T9AP1D52-24 T9AP1D52-48 T9AP1D54-24 T9AP5D52-12 T9AP5D52-24 T9AP5D52-48 T9AP5D54-12 T9AP5D54-24 T9AS1D12-5 T9AS1D12-9 T9AS1D12-12 T9AS1D12-15 T9AS1D12-18 T9AS1D12-24 T9AS1D12-48 T9AS1D12-110 T9AS1D14-12 T9AS1D14-24 T9AS1D17-12 T9AS1D17-24 T9AS1D22-5 T9AS1D22-12 T9AS1D22-24 T9AS1D22-48 T9AS1D22-110 T9AS1D27-12 T9AS1D27-24 T9AS1L12-12 T9AS1L12-24 T9AS1L22-18 T9AS2L22-24 T9AS5D12-5 T9AS5D12-12 T9AS5D12-18 T9AS5D12-24 T9AS5D12-48 T9AS5D12-110 T9AS5D14-5 T9AS5D22-5 T9AS5D22-12 T9AS5D22-24 T9AS5D22-110 T9AS5D24-5 T9AS5D24-12 T9AS5D24-24 T9AS5L12-12 T9AS5L22-18 T9AS5L22-24 T9AS5L22-48 T9AV1D12-12 T9AV1D12-18 T9AV1D22-18 T9AV1D22-24 T9AV1D22-48 T9AV1L12-12 T9AV1L22-24 T9AV2D22-24 T9AV5D12-24 T9AV5D22-18 T9AV5D22-24 T9AV5L12-12 Open (no cover) 1 form A, 1 NO 1 form C, 1 CO 900mW pcb + QC pcb terminals pcb + QC Flanged mount, QC AgCdO 24VDC 1419104-6 1-1393210-0 1419104-9 6-1419102-0 6-1419102-3 5-1419102-8 7-1423091-3 5-1419102-4 5-1419102-2 6-1419102-4 7-1423091-4 7-1423091-5 2-1393210-0 2-1393210-2 1-1393210-3 1-1393210-4 1-1393210-5 1-1393210-8 1-1393210-9 1-1393210-2 5-1423091-7 6-1423091-3 1423029-5 1423029-6 2-1419104-3 1-1419104-7 2-1419104-1 2-1419104-2 1-1419104-6 2071229-4 2071229-4 2-1393210-4 2-1393210-5 2-1419104-6 1423794-1 3-1393210-9 3-1393210-3 3-1393210-4 3-1393210-7 3-1393210-8 3-1393210-2 6-1423091-4 3-1419104-9 3-1419104-3 3-1419104-6 3-1419104-2 6-1423091-9 7-1423091-0 7-1423091-1 4-1393210-1 4-1419104-0 4-1419104-1 9-1419136-6 4-1393210-3 5-1393210-2 4-1419148-8 5-1419148-0 2-1423091-3 1-1423091-8 4-1419104-2 1419137-1 4-1393210-8 5-1419148-2 1419137-2 1423091-6 Unsealed, plastic dust cover 1 form A, 1 NO 1W AgSnOInO AgCdO 1 form C, 1 CO AgSnOInO Wash tight, knock off nib 1 form A, 1 NO pcb terminals AgCdO AgSnOInO AgCdO Enhanced pcb + QC AgCdO AgCdO Enhanced 900mW pcb terminals AgCdO pcb + QC 1 form B, 1 NC 1 form C, 1 CO 1W pcb terminals pcb + QC AgSnOInO AgCdO AgSnOInO Vented, flux tight 08-2012, Rev. 0812 www.te.com © 2012 Tyco Electronics Corporation, a TE Connectivity Ltd. company 1 form A, 1 NO 900mW pcb terminals pcb + QC 1W pcb terminals AgCdO 12VDC 24VDC 48VDC 24VDC 12VDC 24VDC 48VDC 12VDC 24VDC 5VDC 9VDC 12VDC 15VDC 18VDC 24VDC 48VDC 110VDC 12VDC 24VDC 12VDC 24VDC 5VDC 12VDC 24VDC 48VDC 110VDC 12VDC 24VDC 12VDC 24VDC 18VDC 24VDC 5VDC 12VDC 18VDC 24VDC 48VDC 110VDC 5VDC 12VDC 24VDC 110VDC 5VDC 12VDC 24VDC 12VDC 18VDC 24VDC 48VDC 12VDC 18VDC pcb + QC 900mW 1 form B, 1NC 1 form C, 1CO pcb terminals pcb + QC 24VDC 48VDC 12VDC 24VDC 1W pcb terminals pcb + QC 900mW Datasheets and product specification according to IEC 61810-1 and to be used only together with the ‘Definitions’ section. pcb terminals Datasheets and product data is subject to the terms of the disclaimer and all chapters of the ‘Definitions’ section, available at http://relays.te.com/definitions 18VDC 24VDC 12VDC Datasheets, product data, ‘Definitions’ section, application notes and all specifications are subject to change.