NKK B12JJPC_12

Rockers
Toggles
Series B
A
Subminiature Fully Illuminated Toggles
General Specifications
Slides
Rotaries
Keylocks
Programmable Illuminated PB
Pushbuttons
Electrical Capacity (Resistive Load)
Logic Level: 0.4VA maximum @ 28V AC/DC maximum
(Applicable Range 0.1mA ~ 0.1A @ 20mV ~ 28V)
Note: Find additional explanation of operating range in Supplement section.
Other Ratings
Contact Resistance: 50 milliohms maximum
Insulation Resistance: 500 megohms minimum @ 500V DC
Dielectric Strength: 500V AC minimum for 1 minute minimum
Mechanical Life: 100,000 operations minimum
Electrical Life: 50,000 operations minimum
Nominal Operating Force:1.18N
Contact Timing: Nonshorting (break-before-make)
Angle of Throw: 26°
Materials & Finishes
Actuator:
Bushing Housing:
Case Housing:
Support Bracket:
Movable Contact:
Stationary Contacts:
Terminals:
Operating Temperature Range:
Humidity: Vibration:
Shock:
–25°C through +55°C (–13°F through +131°F)
90 ~ 95% humidity for 240 hours @ 40°C (104°F)
10 ~ 55Hz with peak-to-peak amplitude of 1.5mm traversing the frequency range
& returning in 5 minutes; 3 right angled directions for 2 hours
50G (490m/s2) acceleration (tested in 3 right angled directions, with 5 shocks in each direction)
Tilt
Tactiles
Environmental Data
Polyamide
Polyamide
Glass fiber reinforced polyamide
Phosphor bronze with tin plating
Phosphor bronze with gold plating
Brass with tin plating
Brass with gold plating
Soldering: Cleaning:
Wave Soldering recommended. See Profile A in Supplement section.
Manual Soldering: See Profile A in Supplement section.
Automated alcohol based cleaning recommended, 5 minutes maximum. Do not use high-purity alcohol (50% alcohol or more) or organic solvent. High alcohol solution can damage clear plastic.
See Cleaning specifications in Supplement section.
Standards & Certifications
The B Series illuminated toggles have not been tested for UL recognition or CSA certification.
These switches are designed for use in a low-voltage, low-current, logic-level circuit.
When used as intended in a logic-level circuit, the results do not produce hazardous energy.
Supplement
Accessories
Indicators
Touch
PCB Processing
A20
www.nkk.com
A
Rockers
Distinctive Characteristics
Toggles
Series B
Subminiature Fully Illuminated Toggles
Programmable Illuminated PB
Pushbuttons
LED provides maximum illumination to bushing and actuator,
indicating actuator status in highly visible green, red, or
amber for single color or red/green for bicolor.
(Patent pending.)
Totally sealed body construction prevents contact
contamination and allows time- and money-saving
automated soldering and cleaning. Molded-in,
epoxy sealed terminals lock out flux and other
contaminants.
Rotaries
Keylocks
Award-winning STC contact mechanism with
benefits unavailable in conventional mechanisms:
smoother, positive detent actuation, increased
contact stability, and unparalleled logic-level
reliability. (Additional STC details in Terms &
Acronyms; see Supplement section.)
Touch
Tilt
Tactiles
Slides
.100” x .100” (2.54mm x 2.54mm) terminal
spacing conforms to standard PC board grid
spacing.
Supplement
Accessories
Indicators
Actual Size
www.nkk.com
A21
TYPICAL SWITCH ORDERING EXAMPLE
B
Pushbuttons
1
Poles
1
2
J
ON
J
NONE
J
ON
ON
OFF
ON
Combines with
bicolor LED only
C
PC Terminals
Clear
Combines with single color
or bicolor LEDs
3
P
Actuator
Circuits
2
SPDT
LEDs
P
Straight
H
Right Angle
C
Red
V
Vertical
D
Amber
F
Green
Single Color
ON-NONE-ON only
Bushing
J
Bicolor
Clear
CF
Red/Green
ON-NONE-ON
& ON-OFF-ON
Keylocks
Programmable Illuminated PB
Subminiature Fully Illuminated Toggles
A
Rockers
Toggles
Series B
DESCRIPTION FOR TYPICAL ORDERING EXAMPLE
Rotaries
B12JJPC
Clear Toggle & Bushing
with Red LED
Slides
SPDT
ON-NONE-ON Circuit
Tactiles
Straight
PC Terminals
POLE & CIRCUITS
Up
Pole
Model
Throw
Center
Connected Terminals
Down
SPDT
Throw & Schematics
Up
Center
Down
Note: Terminal numbers are not actually on the switch. LED circuit is isolated and requires an external power source.
Slot
Slot
B12
ON
NONE
ON
2-3
NONE
2-1
B13
ON
OFF
ON
2-3
OPEN
2-1
2 (COM)
3
(4) Red
(5)
(6)
ACTUATOR & BUSHING
J
(6.3)
.248
Supplement
J
26°
Clear Toggle
(1.9) Dia
.075
(3.5)
.138
A22
www.nkk.com
(5)
(6) Green
1
Single Color
Accessories
Indicators
Touch
Tilt
Toggle Position
Clear Bushing
Bicolor
A
LED COLORS & SPECIFICATIONS
Colors
Bicolor
C
D
F
CF
Red
Amber
Green
Red/Green
Rockers
Single Color
I FM
30mA
30mA
20mA
30mA/20mA
Typical Forward Current
IF
20mA
20mA
10mA
20mA/10mA
Forward Voltage
VF
1.9V
1.9V
3.4V
1.9V/3.4V
Reverse Peak Voltage
VRM
5V
5V
5V
5V/5V
0.28mA/°C
0.43mA/°C/0.28mA/°C
Current Reduction Rate Above 25°C ∆I F
0.43mA/°C
Ambient Temperature Range
Pushbuttons
Forward Peak Current
–25°C ~ +55°C
PC TERMINALS
H
Straight
V
Right Angle with Bracket
Vertical with Bracket
Keylocks
P
TYPICAL SWITCH DIMENSIONS
Straight PC
26°
1
4
2
5
3
(8.8)
.346
(0.8)
.031
(13.1)
.516
2
6
3
(0.8) Dia Typ
.031
(2.54) Typ
.100
(3.1)
.122
1
5
Slides
(3.5)
.138
(6.3)
.248
6
4
(5.08)
.200
Terminal 4 is a support pin on single color models.
B12JJPC
Right Angle PC
26°
1
6
5
4
(8.8)
.346
(2.54) Typ
.100
1
2
3
4
5
6
(5.08)
.200
(16.42)
.646
(2.54)
.100
(5.08)
.200
(0.5)
.020
(0.8) Dia Typ
.031
(0.6) Dia Typ
.024
(2.54) Typ
.100
Terminal 4 is a support pin on single color models.
26°
(3.1)
.122
1
4
2
5
3
6
(8.8)
.346
Slot
(0.6) Typ
.024
(5.08)
.200
(8.8)
.346
(2.7)
.106
(6.3)
.248
B13JJHCF
Vertical PC
(1.9) Dia
.075
(6.0) Dia
.236
Touch
(0.4)
.016
(2.54)
.100
Tilt
2
Slot
(2.7)
.106
(6.3)
.248
(5.08)
.200
(8.8)
.346
3
(0.4)
.016
(5.08)
.200
(18.96)
.746
(5.08)
.200
4
1
5
2
6
3
Accessories
(0.6) Typ
.024
(1.9) Dia
.075
(3.1)
.122
(2.54) Typ
.100
(5.08)
.200
(0.5) Typ
.020
(2.54) Typ
.100
(5.08)
.200
(0.6) Dia Typ
.024
(0.8) Dia Typ
.031
Terminal 4 is a support pin on single color models.
www.nkk.com
Supplement
(6.0) Dia
.236
Tactiles
Slot
(8.8)
.346
(5.08)
.200
(2.54) Typ
.100
Rotaries
(0.6) Dia Typ
.024
Indicators
(1.9) Dia
.075
(6.0) Dia
.236
Programmable Illuminated PB
LEDs are an integral part
of the switch and not
available separately. The
electrical specifications
shown are determined at
a basic temperature of
25°C. If the source voltage exceeds the rated
voltage, a ballast resistor
is required.
The resistor value can be
calculated by using the
formula in the Supplement
section.
Toggles
Series B
Subminiature Fully Illuminated Toggles
B13JJVCF
A23