TI PTH12060WAD

PTH12060W/L
www.ti.com
SLTS217D – MAY 2003 – REVISED OCTOBER 2005
10-A, 12-V INPUT NON-ISOLATED WIDE-OUTPUT
ADJUST POWER MODULE
FEATURES
•
•
•
•
•
•
•
•
•
•
•
•
•
Up to 10-A Output Current
12-V Input Voltage
Wide-Output Voltage Adjust
(1.2 V to 5.5 V)/(0.8 V to 1.8 V)
Efficiencies up to 95%
225 W/in3 Power Density
On/Off Inhibit
Output Voltage Sense
Margin Up/Down Controls
Undervoltage Lockout
Auto-Track™ Sequencing
Output Overcurrent Protection (Non-latching,
Auto-Reset)
Operating Temperature: –40°C to 85°C
Safety Agency Approvals:
UL 60950, cUL 600950, EN60950 VDE
•
Point-of-Load Alliance (POLA™) Compatible
APPLICATIONS
•
Complex Digital Systems
Nominal Size = 1 in x 0.62 in
(25,4 mm x 15,75 mm)
DESCRIPTION
The PTH12060 series is a non-isolated power module, and part of a new class of complete dc/dc converters
from Texas Instruments. These modules are small in size, and are an alternative for applications requiring up to
10 A of load current.
The small footprint, (1 inch × 0.62 inch) and industry leading features makes this module suitable for space
conscious digital systems that incorporate multiple processors.
This series of modules operate from a 12-V input bus voltage to provide step-down power conversion to a wide
range of output voltages. The output voltage of the W-suffix device may be set to any voltage over the adjust
range, 1.2 V to 5.5 V. The L-suffix device has an adjustment range of 0.8 V to 1.8 V. The output voltage is set
within the adjust range using a single external resistor.
This product includes Auto-Track™ Sequencing. Auto-Track simplifies the task of supply voltage sequencing in a
power system, by enabling modules to track each other, or any other external voltage, during power up and
power down.
Other features include an on/off inhibit and margin up/down controls. An output voltage sense ensures tight load
regulation. Non-latching overcurrent trip protects against load faults.
Target applications are complex digital systems that incorporate the industry's high-speed TMS320™ DSP
family, ASICs, FPGAs, micro-processors, and bus drivers.
Please be aware that an important notice concerning availability, standard warranty, and use in critical applications of Texas
Instruments semiconductor products and disclaimers thereto appears at the end of this data sheet.
Auto-Track, POLA, TMS320 are trademarks of Texas Instruments.
PRODUCTION DATA information is current as of publication date.
Products conform to specifications per the terms of the Texas
Instruments standard warranty. Production processing does not
necessarily include testing of all parameters.
Copyright © 2003–2005, Texas Instruments Incorporated
PTH12060W/L
www.ti.com
SLTS217D – MAY 2003 – REVISED OCTOBER 2005
These devices have limited built-in ESD protection. The leads should be shorted together or the device
placed in conductive foam during storage or handling to prevent electrostatic damage to the MOS gates.
STANDARD APPLICATION
Margin Down
Track
Margin Up
VI
8
7
2
6
3
4
5
Inhibit
CI
560 mF
(Required)
VO
VOSense
RSET, 1%
(Required)
+
10 9
1
CO1
330 mF
(Optional)
+
GND
A.
CO2
Ceramic
(Optional)
L
O
A
D
GND
RSET = Required to set the output voltage to a value higher than the minimum value. See the Application Information
section for values.
ORDERING INFORMATION
PTH12060 (Base Part Number)
Output Voltage Range
1.2 V–5.5 V (Adjustable)
0.8 V–1.8 V (Adjustable)
(1)
(2)
(3)
(4)
2
(1)
DESCRIPTION
PTH12060WAH
Horizontal T/H
Part Number
Pb – free and
RoHS
Yes
(3)
Mechanical
Package (2)
EUW
PTH12060WAS
Standard SMD
No
(4)
PTH12060WAZ
Optional SMD
Yes
(3)
EUY
PTH12060LAH
Horizontal T/H
Yes
(3)
EUW
PTH12060LAS
Standard SMD
No
(4)
EUY
PTH12060LAZ
Optional SMD
Yes
(3)
EUY
Add T to end of part number for tape and reel on SMD packages only.
Reference the applicable package reference drawing for the dimensions and PC board layout.
Lead (Pb) – free option specifies Sn/Ag pin solder material.
Standard option specifies 63/37, Sn/Pb pin solder material.
EUY
PTH12060W/L
www.ti.com
SLTS217D – MAY 2003 – REVISED OCTOBER 2005
ABSOLUTE MAXIMUM RATINGS
voltages are with respect to GND
UNIT
VI
Input voltage
Track
TA
Operating temperature
range
Over VI range
Twave
Wave solder
temperature
Surface temperature of module body or pins (5 seconds)
Treflow
Solder reflow
temperature
Surface temperature of module body or pins
Tstg
Storage temperature
Per Mil-STD-883D, Method 2002.3, 1 msec, ½ Sine, mounted
Mechanical vibration
Mil-STD-883D, Method 2007.2, 20-2000 Hz
Weight
(1)
(2)
–40°C to 85°C (1)
PTH12060WAH
260°C
(2)
PTH12060WAS
235°C
(2)
PTH12060WAZ
260°C
(2)
–40°C to 125°C
Mechanical shock
Flammability
–0.3 V to VI +0.3 V
500 G
20 G
5 grams
Meets UL 94V-O
For operation below 0°C, the external capacitors must have stable characteristics. Use either a low ESR tantalum, Os-Con, or ceramic
capacitor.
During soldering of package version, do not elevate peak temperature of the module, pins or internal components above the stated
maximum.
3
PTH12060W/L
www.ti.com
SLTS217D – MAY 2003 – REVISED OCTOBER 2005
ELECTRICAL CHARACTERISTICS
TA = 25°C; VI = 12 V; VO = 3.3 V; CI = 560 µF, CO = 0 µF, and IO = IOmax (unless otherwise stated)
PARAMETER
IO
Output current
Over ∆Vadj range
VI
Input voltage range
Over IO range
VO
PTH12060W
TEST CONDITIONS
MIN
TA = 60°C, 200 LFM airflow
TYP
0
10 (1)
TA = 25°C, natural convection
10.8
Set-point voltage tolerance
tol
∆Regtemp
Temperature variation
mV
Over Vin range
±10
Over Io range
±12
∆Regtot
Total output variation
Includes set-point, line, load, –40°C ≤ TA ≤ 85°C
∆Vadj
Output voltage adjust range
Over Vin range
∆Vtr
IO = 8 A
VO ripple (peak-to-peak)
20-MHz bandwidth,
with CO2 = 10 µF ceramic
Overcurrent threshold
Reset, followed by auto-recovery
Transient response
1 A/µs load step, 50 to
100% Iomax,
CO1 = 330 µF
VOadj
Margin up/down adjust
IILmargin
Margin input current (pins 9/10)
Pin to GND
IILtrack
Track input current (pin 8)
Pin to GND
dVtrack/dt
Track slew rate capability
CO ≤ CO (max)
UVLO
Undervoltage lockout
Inhibit Control (pin 3)
IIL inhibit
Input low current
Pin to GND
II inhibit
Input standby current
Inhibit (pin 3) to GND, Track (pin 8) open
fs
Switching frequency
Over VI and IO ranges
CI
External input capacitance
(1)
(2)
(3)
(4)
(5)
(6)
(7)
(8)
(9)
4
92%
90%
RSET = 11.5 kΩ, VO = 1.8 V
87%
%VO
5.5
V
RSET = 24.3 kΩ, VO = 1.5 V
85%
RSET = open circuit, VO = 1.2 V
83%
VO ≤ 2.5 V
25 (3)
mVPP
VO > 2.5 V
1 (3)
%VO
20
A
Recovery time
70
µS
Vo over/undershoot
100
mV
–8
(4)
µA
–0.11 (5)
1
9.5
8.8
10.4
9
mA
V/ms
V
Referenced to GND
Input low voltage
Reliability
RSET = 2.0 kΩ, VO = 3.3 V
RSET = 4.32 kΩ, VO = 2.5 V
VI decreasing
VIL
MTBF
94%
VI increasing
Input high voltage
External output capacitance
1.2
RSET = 280 Ω, VO = 5.0 V
mV
±3
±5%
VIH
CO
%VO
%VO
Load regulation
ttr
V
±2 (2)
Line regulation
IO trip
A
13.2
±0.5
∆Regline
Efficiency
A
10 (1)
–40°C < TA < 85°C
∆Regload
η
UNIT
MAX
VI – 0.5
Open (5)
–0.2
0.5
300
0.24
mA
10
mA
350
400
330 (7)
5500 (8)
560 (6)
Capacitance value
Nonceramic
0
Ceramic
0
V
kHz
µF
300
µF
Equivalent series resistance (nonceramic)
4 (9)
mΩ
Per Bellcore TR-332, 50% stress, TA = 40°C, ground benign
6.4
106 Hr
See SOA curves or consult factory for appropriate derating.
The set-point voltage tolerance is affected by the tolerance and stability of RSET. The stated limit is unconditionally met if RSET has a
tolerance of 1% with 100 ppm/°C or better temperature stability.
The peak-to-peak output ripple voltage is measured with an external 10-µF ceramic capacitor. See the standard application schematic.
A small, low leakage (<100 nA) MOSFET is recommended to control this pin. The open-circuit voltage is less than 1 Vdc.
This control pin has an internal pull-up to the input voltage VI (7.5 V for pin 8). If it is left open-circuit, the module operates when input
power is applied. A small, low-leakage (<100 nA) MOSFET or open-drain/collector voltage supervisor IC is recommended for control.
For further information, see the related application information section.
A 560 µF input capacitor are required for proper operation. The electrolytic capacitor must be rated for a minimum of 1050 mA rms of
ripple current.
An external output capacitor is not required for basic operation. Adding 330 µF of distributed capacitance at the load improves the
transient response.
This is the calculated maximum. The minimum ESR limitation oftens result in a lower value. When controlling the Track pin using a
voltage supervisor, CO(max) is reduced to 2200 µF. See the application notes for further guidance.
This is the typical ESR for all the electrolytic (nonceramic) output capacitance. Use 7 mΩ as the minimum when using max-ESR values
to calculate.
PTH12060W/L
www.ti.com
SLTS217D – MAY 2003 – REVISED OCTOBER 2005
ELECTRICAL CHARACTERISTICS
TA = 25°C; VI = 12 V; VO = 1.8 V; CI = 560 µF, CO = 0 µF, and IO = IOmax (unless otherwise stated)
PARAMETER
IO
Output current
VI
VO
Input voltage range
PTH12060L
TEST CONDITIONS
Over ∆Vadj range
MIN
TYP
85°C, 200 LFM airflow
0
10 (1)
25°C, natural convention
0
10 (1)
Over IO range
10.8
Set-point voltage tolerance
tol
UNIT
MAX
A
13.2
V
±2 (2)
%VO
∆Regtemp
Temperature variation
–40°C < TA < 85°C
±0.5
%VO
∆Regline
Line regulation
Over VI range
±10
mV
∆Regload
Load regulation
Over IO range
±12
∆Regtot
Total output variation
Includes set-point, line, load, –40°C ≤ TA ≤ 85°C
∆Vadj
Output voltage adjust range
Over VI range
Efficiency
η
IO trip
ttr
∆Vtr
IO = 8 A
VO ripple (peak-to-peak)
20-MHz bandwidth,
with CO2 = 10 µF ceramic
Overcurrent threshold
Reset, followed by auto-recovery
Transient response
1 A/µs load step, 50 to 100%
IOmax,
CO1 = 330 µF
VOadj
Margin up/dow adjust
IILmargin
Margin input current (pins 9/10)
Pin to GND
IILtrack
Track input current (pin 8)
Pin to GND
dVtrack/dt
Track slew rate capability
CO ≤ CO (max)
UVLO
Under-voltage lockout
Inhibit Control (pin 3)
IIL inhibit
Input low current
Pin to GND
II inhibit
Input standby current
Inhibit (pin 3) to GND, Track (pin 8) open
fs
Switching frequency
Over VI and IO ranges
CI
External input capacitance
(1)
(2)
(3)
(4)
(5)
(6)
(7)
(8)
(9)
84%
RSET = 32.4 kΩ, VO = 1 V
82%
RSET = open circuit, VO = 0.8 V
81%
VO > 1 V
20 (3)
VO ≤ 1 V
30 (3)
1.8
V
mVPP
20
A
Recovery time
70
µS
VO over/undershoot
100
mV
–8 (4)
µA
–0.11 (5)
1
9.5
8.8
10.4
9
mA
V/ms
V
Referenced to GND
Input low voltage
Reliability
87%
VI decreasing
VIL
MTBF
RSET = 3.57 kΩ, VO = 1.5 V
RSET = 12.1 kΩ, VO = 1.2 V
VI increasing
Input high voltage
External output capacitance
88%
%VO
±5%
VIH
CO
0.8
RSET = 130 Ω, VO = 1.8 V
mV
±3
VI – 0.5
Open (5)
–0.2
0.5
200
0.24
mA
10
mA
250
300
330 (7)
5500 (8)
560 (6)
Capacitance value
Nonceramic
Ceramic
0
0
Equivalent series resistance (nonceramic)
4 (9)
Per Bellcore TR-332
50% stress, TA = 40°C, ground benign
6.4
V
kHz
µF
300
µF
mΩ
106 Hr
See SOA curves or consult factory for appropriate derating.
The set-point voltage tolerance is affected by the tolerance and stability of RSET. The stated limit is unconditionally met if RSET has a
tolerance of 1% with 100 ppm/°C or better temperature stability.
The peak-to-peak output ripple voltage is measured with an external 10-µF ceramic capacitor. See the standard application schematic.
A small, low-leakage (<100 nA) MOSFET is recommended to control this pin. The open-circuit voltage is less than 1 Vdc.
This control pin has an internal pull-up to the input voltage VI (7.5 V for pin 8). If it is left open-circuit, the module operates when input
power is applied. A small, low-leakage (<100 nA) MOSFET or open-drain/collector voltage supervisor IC is recommended for control.
For further information, see the application information section.
A 560-µF input capacitor are required for proper operation. The electrolytic capacitor must be rated for a minimum of 1050 mA rms of
ripple current.
An external output capacitor is not required for basic operation. Adding 330 µF of distributed capacitance at the load improves the
transient response.
This is the calculated maximum. The minimum ESR limitation oftens result in a lower value. When controlling the Track pin using a
voltage supervisor, CO(max) is reduced to 2200 µF. See the application notes for further guidance.
This is the typical ESR for all the electrolytic (nonceramic) output capacitance. Use 7 mΩ as the minimum when using max-ESR values
to calculate.
5
PTH12060W/L
www.ti.com
SLTS217D – MAY 2003 – REVISED OCTOBER 2005
DEVICE INFORMATION
Terminal Functions
TERMINAL
NAME
NO.
DESCRIPTION
VI
2
The positive input voltage power node to the module, which is referenced to common GND.
VO
6
The regulated positive power output with respect to the GND node.
GND
1, 7
Inhibit
3
VO Adjust
4
This is the common ground connection for the VI and VO power connections. It is also the 0 Vdc reference for the
control inputs.
The Inhibit pin is an open-collector/drain negative logic input that is referenced to GND. Applying a low level ground
signal to this input disables the module’s output and turns off the output voltage. When the Inhibit control is active,
the input current drawn by the regulator is significantly reduced. If the Inhibit pin is left open-circuit, the module
produces an output whenever a valid input source is applied.
A 1% resistor must be directly connected between this pin and GND (pin 1) to set the output voltage of the module
to a value higher than its lowest value. The temperature stability of the resistor should be 100 ppm/°C (or better).
The set-point range is 1.2 V to 5.5 V for W-suffix devices, and 0.8 V to 1.8 V for L-suffix devices. The resistor value
required for a given output voltage may be calculated using a formula. If left open circuit, the output voltage defaults
to its lowest value. For further information on output voltage adjustment, see the application information section.
Table 2 gives the preferred resistor values for a number of standard output voltages.
VO Sense
Track
5
The sense input allows the regulation circuit to compensate for voltage drop between the module and the load. For
optimal voltage accuracy, VO Sense should be connected to VO. It can also be left disconnected.
8
This is an analog control input that enables the output voltage to follow an external voltage. This pin becomes
active typically 20 ms after the input voltage has been applied, and allows direct control of the output voltage from
zero volts, up to the nominal set-point voltage. Within this range, the output follows the voltage at the Track pin on a
volt-for-volt basis. When the control voltage is raised above this range, the module regulates at its set-point voltage.
The feature allows the output voltage to rise simultaneously with other modules powered from the same input bus.
If unused, this input should be connected to VI.
Note: Due to the undervoltage lockout feature, the output of the module cannot follow its own input voltage during
power up. For more information, see the application information section.
Margin Down
9
When this input is asserted to GND, the output voltage is decreased by 5% from the nominal. The input requires an
open-collector (open-drain) interface. It is not TTL compatible. A lower percent change can be accommodated with
a series resistor. For further information, see the application information section.
Margin Up
10
When this input is asserted to GND, the output voltage is increased by 5%. The input requires an open-collector
(open-drain) interface. It is not TTL compatible. The percent change can be reduced with a series resistor. For
further information, see the application information section.
1
10
9
8
7
PTHXX060
(Top View)
2
6
3
6
4
5
PTH12060W/L
www.ti.com
SLTS217D – MAY 2003 – REVISED OCTOBER 2005
PTH12060W TYPICAL CHARACTERISTICS (VI = 12 V) (1) (2)
EFFICIENCY
vs
OUTPUT CURRENT
100
OUTPUT RIPPLE
vs
OUTPUT CURRENT
(see Note 3 of table)
100
VO = 3.3 V
VO = 2.5 V
VO = 5 V
80
80
VO = 1.2 V
VO = 1.5 V
Output Ripple − mV
Efficiency − %
90
VO = 1.8 V
70
VO = 3.3 V
60
VO = 5 V
VO = 2.5 V
VO = 1.8 V
40
60
20
50
0
VO = 1.5 V
0
2
4
6
8
0
10
2
Figure 2.
POWER DISSIPATION
vs
OUTPUT CURRENT
TEMPERATURE DERATING
vs
OUTPUT CURRENT
90
(2)
TA − Ambient Temperature −5 C
PD − Power Dissipation − W
(1)
8
Figure 1.
5
4
VO = 5 V
VO = 3.3 V
3
VO = 2.5 V
2
1
VO = 1.2 V
0
6
2
4
6
10
IO − Output Current − A
IO − Output Current − A
0
VO = 1.2 V
4
8
10
400LFM
Nat Conv
80
100 LFM
70
200 LFM
60
50
40
30
20
0
2
4
6
IO − Output Current − A
IO − Output Current − A
Figure 3.
Figure 4.
8
10
Characteristic data has been developed from actual products tested at 25°C. This data is considered typical data for the Converter.
Applies to Figure 1, Figure 2, and Figure 3.
SOA graphs represent the conditions at which internal components are at or below the manufacturer's maximum operating
temperatures. Derating limits apply to modules soldered directly to a 4 in × 4 in, double-sided PCB with 1 oz copper. For surface mount
products (AS and AZ suffix), multiple vias (plated through holes) are required to add thermal paths around the power pins. Please refer
to the mechanical specification for more information. Applies to Figure 4.
7
PTH12060W/L
www.ti.com
SLTS217D – MAY 2003 – REVISED OCTOBER 2005
PTH12060L TYPICAL CHARACTERISTICS (VI = 12 V) (1) (2)
EFFICIENCY
vs
OUTPUT CURRENT
OUTPUT RIPPLE
vs
OUTPUT CURRENT
100
100
VO = 1.5 V
VO = 1.2 V
VO = 1.8 V
80
VO = 0.8 V
80
Output Ripple − mV
Efficiency − %
90
VO = 1 V
70
60
VO = 1 V
40
60
20
50
0
VO = 1.5 V
VO = 1.8 V
VO = 1.2
V
VO = 0.8 V
0
2
4
6
8
10
(2)
8
4
6
8
Figure 5.
Figure 6.
POWER DISSIPATION
vs
OUTPUT CURRENT
TEMPERATURE DERATING
vs
OUTPUT CURRENT
10
90
VO = 1.8 V
2.5
TA− Ambient Temperature −5 C
PD − Power Dissipation − W
(1)
2
IO − Output Current − A
3
VO = 1.5 V
VO = 1.2 V
2
VO = 1 V
1.5
1
VO = 0.8
V
0.5
0
0
IO − Output Current − A
0
2
4
6
8
10
Nat Conv
80
100 LFM
70
60
50
40
30
20
VO = ≤1.8 V
0
2
4
6
IO − Output Current − A
IO − Output Current − A
Figure 7.
Figure 8.
8
10
Characteristic data has been developed from actual products tested at 25°C. This data is considered typical data for the Converter.
Applies to Figure 5, Figure 6, and Figure 7.
SOA graphs represent the conditions at which internal components are at or below the manufacturer's maximum operating
temperatures. Derating limits apply to modules soldered directly to a 4 in × 4 in, double-sided PCB with 1 oz copper. For surface mount
products (AS and AZ suffix), multiple vias (plated through holes) are required to add thermal paths around the power pins. Please refer
to the mechanical specification for more information. Applies to Figure 8.
PTH12060W/L
www.ti.com
SLTS217D – MAY 2003 – REVISED OCTOBER 2005
APPLICATION INFORMATION
CAPACITOR RECOMMENDATIONS FOR THE PTH12060 SERIES OF POWER MODULES
Input Capacitor
The recommended input capacitance is determined by the 560 µF minimum capacitance and 1050 mArms
minimum ripple current rating. A 10 µF X5R/X7R ceramic capacitor can be added to reduce the reflected input
ripple current. The ceramic capacitor should be located between the input electrolytic and the module.
Ripple current, less than 100 mΩ equivalent series resistance (ESR) and temperature, are major considerations
when selecting input capacitors. Unlike polymer-tantalum capacitors, regular tantalum capacitors have a
recommended minimum voltage rating of 2 × (max. dc voltage + ac ripple). No tantalum capacitors were found
with sufficient voltage rating to meet this requirement. At temperatures below 0°C, the ESR of aluminum
electrolytic capacitors increases. For these applications, Os-Con, polymer-tantalum, and polymer-aluminum types
should be considered.
Output Capacitors (Optional)
For applications with load transients (sudden changes in load current), regulator response benefits from external
output capacitance. The value of 330 µF is used to define the transient response specification. For most
applications, a high quality, computer-grade aluminum electrolytic capacitor is adequate. These capacitors
provide decoupling over the frequency range, 2 kHz to 150 kHz, and are suitable for ambient temperatures
above 0°C. Below 0°C, tantalum, ceramic, or Os-Con type capacitors are recommended. When using one or
more nonceramic capacitors, the calculated equivalent ESR should be no lower than 4 mΩ (7 mΩ using the
manufacturer's maximum ESR for a single capacitor). A list of preferred low-ESR type capacitors are identified in
Table 1.
In addition to electrolytic capacitance, adding a 10 µF X5R/X7R ceramic capacitor to the output reduces the
output ripple voltage and improves the regulator's transient response. The measurement of both the output ripple
and transient response is also best achieved across a 10 µF ceramic capacitor.
Ceramic Capacitors
Above 150 kHz, the performance of aluminum electrolytic capacitors is less effective. Multilayer ceramic
capacitors have a low ESR and a resonant frequency higher than the bandwidth of the regulator. They can be
used to reduce the reflected ripple current at the input, and improve the transient response of the output. When
used on the output, their combined ESR is not critical as long as the total value of ceramic capacitance does not
exceed 300 µF. Also, to prevent the formation of local resonances, do not place more than five identical ceramic
capacitors in parallel with values of 10 µF or greater.
Tantalum Capacitors
Tantalum type capacitors are most suited for use on the output bus, and are recommended for applications
where the ambient operating temperature can be less than 0°C. The AVX TPS, Sprague 593D/594/595, and
Kemet T495/T510 capacitor series are suggested over other tantalum types due to their higher rated surge,
power dissipation, and ripple current capability. As a caution, many general-purpose tantalum capacitors have
considerably higher ESR, reduced power dissipation, and lower ripple current capability. These capacitors are
also less reliable as they have lower power dissipation and surge current ratings. Tantalum capacitors that do not
have a stated ESR or surge current rating are not recommended for power applications.
When specifying Os-con and polymer tantalum capacitors for the output, the minimum ESR limit is encountered
well before the maximum capacitance value is reached.
Capacitor Table
Table 1 identifies the characteristics of capacitors from a number of vendors with acceptable ESR and ripple
current (rms) ratings. The recommended number of capacitors required at both the input and output buses is
identified for each capacitor type.
Note: This is not an extensive capacitor list. Capacitors from other vendors are available with comparable
specifications. Those listed are for guidance. The RMS ripple current rating and ESR (at 100 kHz) are critical
parameters necessary to insure both optimum regulator performance and long capacitor life.
9
PTH12060W/L
www.ti.com
SLTS217D – MAY 2003 – REVISED OCTOBER 2005
APPLICATION INFORMATION (continued)
Designing for Very Fast Load Transients
The transient response of the dc/dc converter is characterized using a load transient with a di/dt of 1 A/µs. The
typical voltage deviation for this load transient is given in the data sheet specification table using the optional
value of output capacitance. As the di/dt of a transient is increased, the response of a converter's regulation
circuit ultimately depends on its output capacitor decoupling network. This is an inherent limitation with any dc/dc
converter once the speed of the transient exceeds its bandwidth capability. If the target application specifies a
higher di/dt or lower voltage deviation, the requirement is met with additional output capacitor decoupling. In
these cases, special attention must be paid to the type, value, and ESR of the capacitors selected.
If the transient performance requirements exceed that specified in this data sheet, or the total amount of load
capacitance is above 3,000 µF, the selection of output capacitors becomes more important.
Table 1. Input/Output Capacitors (1)
Capacitor Characteristics
Capacitor Vendor,
Type/Series (Style)
Working
Voltage
(V)
Value
(µF)
Max ESR
at 100 kHz
(Ω)
Max Ripple
Current at
85°C (Irms)
(mA)
Quantity
Physical Size
(mm)
Input
Bus
Output
Bus
Vendor Number
Panasonic, Aluminum
25
560
0.065
1205
12,5 × 15
1
1
EEUFC1E561S
FC (Radial)
25
1000
0.060
1100
12,5 × 13,5
1
1
EEVFK1E102Q
FK (SMD)
35
680
0.060
1100
12,5 × 13,5
1
1
EEVFK1V681Q
PS, Poly-Aluminum (Radial)
16
330
0.0014
5050
10 × 12,5
2
≤2
16PS330MJ12
LXZ, Aluminum
16
680
0.068
1050
10 × 16
1
1
LXZ16VB681M10X16L
L
PXA, Poly-Aluminum (SMD)
16
330
0.014
5050
10 × 12,2
2
≤2
PXA16VC331MJ12
Nichicon Aluminum PM
(Radial)
25
560
0.060
1060
12,5 × 15
1
1
UPM1E561MHH6
HD (Radial)
16
680
0.038
1430
10 × 16
1
1
UHD1C681MHR
PM (Radial)
35
560
0.048
1360
16 × 15
1
1
UPM1V561MHH6
6.3
180
0.005
4000
7,3 × 4,3 × 4,2
N/R (2)
≤1 (3)
United Chemi-Con
Panasonic, Poly-Aluminum:
S/SE (SMD)
EEFSE0J181R
(VO ≤ 5.1 V)
Sanyo
TPE, ps-Ccap (SMD)
10
330
0.025
3000
7,3 × 5,7
N/R (2)
≤4
10TPE330M
SEPC, Os-con (Radial)
16
470
0.010
>9700
10 × 13
2
≤1
16SEPC470M
SVP, Os-con (SMD)
16
330
0.016
4700
11 × 12
2
≤3
16SVP330M
TPS, Tantalum (SMD)
10
470
0.045
>1723
N/R (2)
≤5 (3)
TPSE477M019R0045
(VO ≤ 5.1 V)
TPS, Tantalum (SMD)
10
330
0.045
>1723
2
≤5 (3)
TPSE337M019R0045
(VO ≤ 5.1 V)
10
330
0.040
1800
N/R (2)
≤5 (3)
T520X337M010AS
N/R (2)
≤2
T53X337M010AS
N/R (2)
≤2 (3)
T530X477M0061S
(VO ≤ 5.1 V)
AVX
7,3 × 5,7 × 4,1
Kemet
T520, Poly-Tantalum (SMD)
T530, Tantalum/Organic
(1)
(2)
(3)
10
10
330
0.015
>3800
6.3
470
0.012
4200
4,3 × 7,3 × 4,0
Capacitor Supplier Verification
Please verify availability of capacitors identified in this table. Capacitor suppliers may recommend alternative part numbers because of
limited availability or obsolete products. In some instances, the capacitor product life cycle may be in decline and have short-term
consideration for obsolescence.
RoHS, Lead-free and Material Details
Please consult capacitor suppliers regarding material composition, RoHS status, lead-free status, and manufacturing process
requirements. Component designators or part number deviations can occur when material composition or soldering requirements are
updated.
N/R – Not recommended. The capacitor voltage rating does not meet the minimum operating limits.
The voltage rating of this capacitor only allows it to be used for output voltages that are equal to or less than 5.1 V.
PTH12060W/L
www.ti.com
SLTS217D – MAY 2003 – REVISED OCTOBER 2005
APPLICATION INFORMATION (continued)
Table 1. Input/Output Capacitors (continued)
Capacitor Characteristics
Quantity
Working
Voltage
(V)
Value
(µF)
Max ESR
at 100 kHz
(Ω)
Max Ripple
Current at
85°C (Irms)
(mA)
Physical Size
(mm)
Input
Bus
Vishay-Sprague
594D, Tantalum (SMD)
10
470
0.100
1440
7,2 × 6 × 4,1
N/R (2)
94SP, Organic (Radial)
16
270
0.018
4200
10 × 10,5
2 (4)
≤3
94SVP, Organic (SMD)
16
330
0.017
4500
10 × 12.7
2
≤2
94SVP337X0016F12
Kemet, Ceramic X5R (SMD)
16
10
0.002
1210 case
1 (5)
≤5
C1210C106M4PAC
6.3
47
0.002
3225 mm
N/R (2)
≤5 (3)
C1210C476K9PAC
1210 case
N/R (2)
≤3
GRM32ER60J107M
3225 mm
N/R (2)
Capacitor Vendor,
Type/Series (Style)
Murata, Ceramic X5R (SMD)
TDK, Ceramic X5R (SMD)
(4)
(5)
0.002
Vendor Number
Output
Bus
595D477X0010R2T
(VO ≤ 5.1 V)
94SP277X0016FBP
6.3
100
6.3
47
≤5
GRM32ER60J476M
16
22
1 (5)
≤5
GRM32ER61C226K
16
10
1 (5)
≤5
GRM32DR61C106K
6.3
100
1210 case
N/R (2)
≤3
C3225X5R0J107MT
6.3
47
3225 mm
N/R (2)
≤5
C3225X5R0J476MT
16
22
1 (5)
≤5
C3225X5R1C226MT
16
10
1 (5)
≤5
C3225X5R1C106MT
0.002
A total capacitance of 540 µF is acceptable based on the combined ripple current rating.
Ceramic capacitors are required to complement electrolytic types at the input and to reduce high-frequency ripple current.
Adjusting the Output Voltage of the PTH12060x Series of Wide-Output Adjust Power Modules
The VO Adjust control (pin 4) sets the output voltage of the PTH12060 product. The adjustment range is from 1.2
V to 5.5 V for the W-suffix modules, and 0.8 V to 1.8 V for L-suffix modules. The adjustment method requires the
addition of a single external resistor, RSET, that must be connected directly between the VO Adjust and GND pins.
Table 2 gives the preferred value of the external resistor for a number of standard voltages, along with the actual
output voltage that the resistance value provides. Figure 9 shows the placement of the required resistor.
Table 2. Preferred Values of RSET for Standard Output Voltages
PTH12060W
VO
(Required)
PTH12060L
RSET
VO
(Actual)
RSET
VO
(Actual)
5V
280 Ω
5.009 V
N/A
N/A
3.3 V
2 kΩ
3.294 V
N/A
N/A
2.5 V
4.32 kΩ
2.503 V
N/A
N/A
2V
8.06 kΩ
2.01 V
N/A
N/A
1.8 V
11.5 kΩ
1.801 V
130 Ω
1.8 V
1.5 V
24.3 kΩ
1.506 V
3.57 kΩ
1.499 V
1.2 V
Open
1.2 V
12.1 kΩ
1.201 V
1.1 V
N/A
N/A
18.7 kΩ
1.101 V
1.0 V
N/A
N/A
32.4 kΩ
0.999 V
0.9 V
N/A
N/A
71.5 kΩ
0.901 V
0.8 V
N/A
N/A
Open
0.8 V
11
PTH12060W/L
www.ti.com
SLTS217D – MAY 2003 – REVISED OCTOBER 2005
For other output voltages, the value of the required resistor can either be calculated, or simply selected from the
range of values given in Table 4. The following formula is used for calculating the adjust resistor value. Select the
appropriate value for the parameters, RS and Vmin, from Table 3.
RSET = 10 kW x
0.8 V
- RS kW
VO - Vmin
(1)
Table 3. Adjust Formula Parameters
Part Number
PTH12060W
PTH12060L
Vmin
1.2 V
0.8 V
Vmax
5.5 V
1.8 V
RS
1.82 kΩ
7.87 kΩ
VOSense
VI
2
9
8
5
3
1
7
CI
560 mF
(Required)
VO
6
PTH12060
4
RSET
1%
+
10
CO
330 mF
(Optional)
+
GND
(1)
A 0.05-W rated resistor can be used. The tolerance should be 1%, with a temperature stability of 100 ppm/°C or
better. Place the resistor as close to the regulator as possible. Connect the resistor directly between pins 4 and 7
using dedicated PCB traces.
(2)
Never connect capacitors from VO Adjust to either GND or VO. Any capacitance added to the VO Adjust pin affects the
stability of the regulator.
Figure 9. VO Adjust Resistor Placement
12
PTH12060W/L
www.ti.com
SLTS217D – MAY 2003 – REVISED OCTOBER 2005
Table 4. Output Voltage Set-Point Resistor Values
PTH12060W
PTH12060L
VO
RSET
VO
RSET
VO
RSET
1.2
Open
2.7
3.51 kΩ
0.8
Open
1.225
318 kΩ
2.75
3.34 kΩ
0.825
312 kΩ
1.25
158 kΩ
2.8
3.18 kΩ
0.85
152 kΩ
1.275
105 kΩ
2.85
3.03 kΩ
0.875
98.8 kΩ
1.3
78.2 kΩ
2.9
2.89 kΩ
0.9
72.1 kΩ
1.325
62.2 kΩ
2.95
2.75 kΩ
0.925
56.1 kΩ
1.35
51.5 kΩ
3
2.62 kΩ
0.95
45.5 kΩ
1.375
43.9 kΩ
3.05
2.5 kΩ
0.975
37.8 kΩ
1.4
38.2 kΩ
3.1
2.39 kΩ
1
32.1 kΩ
1.425
33.7 kΩ
3.15
2.28 kΩ
1.025
27.7 kΩ
1.45
30.2 kΩ
3.2
2.18 kΩ
1.05
24.1 kΩ
1.475
27.3 kΩ
3.25
2.08 kΩ
1.075
21.2 kΩ
1.5
24.8 kΩ
3.3
1.99 kΩ
1.1
18.8 kΩ
1.55
21 kΩ
3.35
1.9 kΩ
1.125
16.7 kΩ
1.6
18.2 kΩ
3.4
1.82 kΩ
1.15
15 kΩ
1.65
16 kΩ
3.5
1.66 kΩ
1.175
13.5 kΩ
1.7
14.2 kΩ
3.6
1.51 kΩ
1.2
12.1 kΩ
1.75
12.7 kΩ
3.7
1.38 kΩ
1.225
11 kΩ
1.8
11.5 kΩ
3.8
1.26 kΩ
1.25
9.91 kΩ
1.85
10.5 kΩ
3.9
1.14 kΩ
1.275
8.97 kΩ
1.9
9.61 kΩ
4
1.04 kΩ
1.3
8.13 kΩ
1.95
8.85 kΩ
4.1
939 Ω
1.325
7.37 kΩ
2
8.18 kΩ
4.2
847 Ω
1.35
6.68 kΩ
2.05
7.59 kΩ
4.3
761 Ω
1.375
6.04 kΩ
2.1
7.07 kΩ
4.4
680 Ω
1.4
5.46 kΩ
4.93 kΩ
2.15
6.6 kΩ
4.5
604 Ω
1.425
2.2
6.18 kΩ
4.6
533 Ω
1.45
4.44 kΩ
2.25
5.8 kΩ
4.7
466 Ω
1.475
3.98 kΩ
3.56 kΩ
2.3
5.45 kΩ
4.8
402 Ω
1.5
2.35
5.14 kΩ
4.9
342 Ω
1.55
2.8 kΩ
2.4
4.85 kΩ
5
285 Ω
1.6
2.13 kΩ
2.45
4.58 kΩ
5.1
231 Ω
1.65
1.54 kΩ
2.5
4.33 kΩ
5.2
180 Ω
1.7
1.02 kΩ
2.55
4.11 kΩ
5.3
131 Ω
1.75
551 Ω
2.6
3.89 kΩ
5.4
85 Ω
1.8
130 Ω
2.65
3.7 kΩ
5.5
41 Ω
Features of the PTH Family of Non-Isolated Wide Output Adjust Power Modules
The PTH/PTV family of non-isolated, wide-output adjustable power modules are optimized for applications that
require a flexible, high performance module that is small in size. Each of these products are POLA™ compatible.
POLA-compatible products are produced by a number of manufacturers, and offer customers advanced,
nonisolated modules with the same footprint and form factor. POLA parts are also ensured to be interoperable,
thereby, providing customers with second-source availability.
From the basic, Just Plug it In functionality of the 6-A modules, to the 30-A rated feature-rich PTHxx030, these
products were designed to be very flexible, yet simple to use. The features vary with each product. Table 5
provides a quick reference to the features by product series and input bus voltage.
13
PTH12060W/L
www.ti.com
SLTS217D – MAY 2003 – REVISED OCTOBER 2005
Table 5. Operating Features by Series and Input Bus Voltage
Series
PTHxx050
PTHxx060
PTHxx010
PTVxx010
PTHxx020
PTVxx020
PTHxx030
Input Bus
IO
Adjust
(Trim)
On/Off
Inhibit
OverCurrent
Prebias
Startup
AutoTrack™
Margin
Up/Down
Output
Sense
Thermal
Shutdown
3.3 V
6A
•
•
•
•
•
5V
6A
•
•
•
•
•
12 V
6A
•
•
•
•
•
3.3 V / 5 V
10 A
•
•
•
•
•
•
•
12 V
8A
•
•
•
•
•
•
•
3.3 V / 5 V
15 A
•
•
•
•
•
•
•
12 V
12 A
•
•
•
•
•
•
•
5V
8A
•
•
•
•
•
12 V
8A
•
•
•
•
•
3.3 V / 5 V
22 A
•
•
•
•
•
•
•
•
12 V
18 A
•
•
•
•
•
•
•
•
5V
18 A
•
•
•
•
•
•
•
12 V
16 A
•
•
•
•
•
•
•
3.3 V / 5 V
30 A
•
•
•
•
•
•
•
•
12 V
26 A
•
•
•
•
•
•
•
•
•
•
For simple point-of-use applications, the PTH12050 (6 A) provides operating features such as an on/off inhibit,
output voltage trim, prebias start-up and overcurrent protection. The PTH12060 (10 A), and PTH12010 (12 A)
include an output voltage sense, and margin up/down controls. Then the higher output current, PTH12020 (18 A)
and PTH12030 (26 A) products incorporate overtemperature shutdown protection.
The PTV12010 and PTV12020 are similar parts offered in a vertical, single in-line pin (SIP) profile, at slightly
lower current ratings.
All of the products referenced in Table 5 include Auto-Track™. This feature was specifically designed to simplify
the task of sequencing the supply voltages in a power system. This and other features are described in the
following sections.
Soft-Start Power Up
The Auto-Track feature allows the power-up of multiple PTH modules to be directly controlled from the Track pin.
However in a stand-alone configuration, or when the Auto-Track feature is not being used, the Track pin should
be directly connected to the input voltage, VI (see Figure 10).
10 9
8
Up Dn Track
2
VI
Inhibit
3
+
GND
CI
1000 mF
PTH12020W
VO
3.3 V
6
GND
Adjust
1
7
4
RSET
2 kW
0.1 W, 1%
+
12 V
5
Sense
CO
330 mF
GND
Figure 10. Power-Up Application Circuit
When the Track pin is connected to the input voltage, the Auto-Track function is permanently disengaged. This
allows the module to power up entirely under the control of its internal soft-start circuitry. When power up is
under soft-start control, the output voltage rises to the set-point at a quicker and more linear rate.
14
PTH12060W/L
www.ti.com
SLTS217D – MAY 2003 – REVISED OCTOBER 2005
VI (5 V/Div)
VO (1 V/Div)
II (5 A/Div)
t - Time = 5 ms/Div
Figure 11. Power-Up Waveforms
From the moment a valid input voltage is applied, the soft-start control introduces a short time delay (typically
8 ms–15 ms) before allowing the output voltage to rise. The output then progressively rises to the module’s
setpoint voltage. Figure 11 shows the soft-start power-up characteristic of the 18-A output product
(PTH12020W), operating from a 12-V input bus, and configured for a 3.3-V output. The waveforms were
measured with a 5-A resistive load and the Auto-Track feature disabled. The initial rise in input current when the
input voltage first starts to rise is the charge current drawn by the input capacitors. Power-up is complete within
25 ms.
Overcurrent Protection
For protection against load faults, all modules incorporate output overcurrent protection. Applying a load that
exceeds the regulator's overcurrent threshold causes the regulated output to shut down. Following shutdown, a
module periodically attempts to recover by initiating a soft-start power-up. This is described as a hiccup mode of
operation, whereby, the module continues in a cycle of successive shutdown and power up until the load fault is
removed. During this period, the average current flowing into the fault is significantly reduced. Once the fault is
removed, the module automatically recovers and returns to normal operation.
Overtemperature Protection (OTP)
The PTH12020, PTV12020, and PTH12030 products have overtemperature protection. These products have an
on-board temperature sensor that protects the module's internal circuitry against excessively high temperatures.
A rise in the internal temperature may be the result of a drop in airflow, or a high ambient temperature. If the
internal temperature exceeds the OTP threshold, the module's Inhibit control is internally pulled low. This turns
the output off. The output voltage drops as the external output capacitors are discharged by the load circuit. The
recovery is automatic, and begins with a soft-start power up. It occurs when the sensed temperature decreases
by about 10°C below the trip point.
Note: The overtemperature protection is a last resort mechanism to prevent thermal stress to the regulator.
Operation at or close to the thermal shutdown temperature is not recommended and will reduce the
long-term reliability of the module. Always operate the regulator within the specified Safe Operating Area
(SOA) limits for the worst-case conditions of ambient temperature and airflow.
Output On/Off Inhibit
For applications requiring output voltage on/off control, each series of the PTH family incorporates an output
Inhibit control pin. The inhibit feature can be used wherever there is a requirement for the output voltage from the
regulator to be turned off.
The power modules function normally when the Inhibit pin is left open-circuit, providing a regulated output
whenever a valid source voltage is connected to VI with respect to GND.
Figure 12 shows the typical application of the inhibit function. Note the discrete transistor (Q1). The Inhibit input
has its own internal pull-up to a potential of 5 V to 13.2 V (see footnotes to specification table). The input is not
compatible with TTL logic devices. An open-collector (or open-drain) discrete transistor is recommended for
control.
15
PTH12060W/L
www.ti.com
SLTS217D – MAY 2003 – REVISED OCTOBER 2005
VOSense
2
5
7
VO
6
4
+
1 = Inhibit
8
PTH12060W
3 1
CI
560 mF
9
CO
Q1
BSS138
+
10
VI
L
O
A
D
RSET 330 mF
2 kW
0.1 W, 1%
GND
GND
Figure 12. Inhibit Control Circuit
Turning on Q1 applies a low voltage to the Inhibit control pin and disables the output of the module. If Q1 is then
turned off, the module executes a soft-start power-up sequence. A regulated output voltage is produced within 25
ms. Figure 13 shows the typical rise in both the output voltage and input current, following the turn off of Q1. The
turn off of Q1 corresponds to the rise in the waveform, Q1 Vds. The waveforms were measured with a 5-A
constant current load.
Q1Vds (5 V/Div)
VO (2 V/Div)
II (2 A/Div)
t - Time = 10 ms/Div
Figure 13. Power-Up from Inhibit Control
Auto-Track™ Function
The Auto-Track function is unique to the PTH/PTV family, and is available with all POLA products. Auto-Track
was designed to simplify the amount of circuitry required to make the output voltage from each module power up
and power down in sequence. The sequencing of two or more supply voltages during power up is a common
requirement for complex mixed-signal applications that use dual-voltage VLSI ICs such as the TMS320™ DSP
family, microprocessors, and ASICs.
How Auto-Track™ Works
Auto-Track works by forcing the module output voltage to follow a voltage presented at the Track control pin (1).
This control range is limited to between 0 V and the module set-point voltage. Once the track-pin voltage is
raised above the set-point voltage, the module output remains at its set-point (2). As an example, if the Track pin
of a 2.5-V regulator is at 1 V, the regulated output is 1 V. If the voltage at the Track pin rises to 3 V, the regulated
output does not go higher than 2.5 V.
When under Auto-Track control, the regulated output from the module follows the voltage at its Track pin on a
volt-for-volt basis. By connecting the Track pin of a number of these modules together, the output voltages follow
a common signal during power up and power down. The control signal can be an externally generated master
ramp waveform, or the output voltage from another power supply circuit (3). For convenience, the Track input
incorporates an internal RC-charge circuit. This operates off the module input voltage to produce a suitable rising
waveform at power up.
16
PTH12060W/L
www.ti.com
SLTS217D – MAY 2003 – REVISED OCTOBER 2005
Typical Application
The basic implementation of Auto-Track allows for simultaneous voltage sequencing of a number of Auto-Track
compliant modules. Connecting the Track inputs of two or more modules forces their track input to follow the
same collective RC-ramp waveform, and allows their power-up sequence to be coordinated from a common
Track control signal. This can be an open-collector (or open-drain) device, such as a power-up reset voltage
supervisor IC. See U3 in Figure 14.
To coordinate a power-up sequence, the Track control must first be pulled to ground potential. This should be
done at or before input power is applied to the modules. The ground signal should be maintained for at least
40 ms after input power has been applied. This brief period gives the modules time to complete their internal
soft-start initialization (4), enabling them to produce an output voltage. A low-cost supply voltage supervisor IC,
that includes a built-in time delay, is an ideal component for automatically controlling the Track inputs at power
up.
Figure 14 shows how the TL7712A supply voltage supervisor IC (U3) can be used to coordinate the sequenced
power up of two 12-V input Auto-Track modules. The output of the TL7712A supervisor becomes active above
an input voltage of 3.6 V, enabling it to assert a ground signal to the common track control well before the input
voltage has reached the module's undervoltage lockout threshold. The ground signal is maintained until
approximately 43 ms after the input voltage has risen above U3's voltage threshold, which is 10.95 V. The 43-ms
time period is controlled by the capacitor C3. The value of 3.3 µF provides sufficient time delay for the modules
to complete their internal soft-start initialization. The output voltage of each module remains at zero until the track
control voltage is allowed to rise. When U3 removes the ground signal, the track control voltage automatically
rises. This causes the output voltage of each module to rise simultaneously with the other modules, until each
reaches its respective set-point voltage.
Figure 15 shows the output voltage waveforms from the circuit of Figure 14 after input voltage is applied to the
circuit. The waveforms, VO1 and VO2, represent the output voltages from the two power modules, U1 (3.3 V) and
U2 (1.8 V), respectively. VTRK, VO1, and VO2 are shown rising together to produce the desired simultaneous
power-up characteristic.
The same circuit also provides a power-down sequence. When the input voltage falls below U3's voltage
threshold, the ground signal is re-applied to the common track control. This pulls the track inputs to zero volts,
forcing the output of each module to follow, as shown in Figure 16. In order for a simultaneous power-down to
occur, the track inputs must be pulled low before the input voltage has fallen below the modules' undervoltage
lockout. This is an important constraint. Once the modules recognize that a valid input voltage is no longer
present, their outputs can no longer follow the voltage applied at their track input. During a power-down
sequence, the fall in the output voltage from the modules is limited by the maximum output capacitance and the
Auto-Track slew rate. If the Track pin is pulled low at a slew rate greater than 1 V/ms, the discharge of the output
capacitors will induce large currents which could exceed the peak current rating of the module. This will result in
a reduction in the maximum allowable output capacitance as listed in the Electrical Characteristics table. When
controlling the Track pin of the PTH12060W using a voltage supervisor IC, the slew rate is increased, therefore
COmax is reduced to 2200 µF.
Notes on Use of Auto-Track™
1. The Track pin voltage must be allowed to rise above the module set-point voltage before the module
regulates at its adjusted set-point voltage.
2. The Auto-Track function tracks almost any voltage ramp during power up, and is compatible with ramp
speeds of up to 1 V/ms.
3. The absolute maximum voltage that may be applied to the Track pin is the input voltage VI.
4. The module cannot follow a voltage at its track control input until it has completed its soft-start initialization.
This takes about 40 ms from the time that a valid voltage has been applied to its input. During this period, it
is recommended that the Track pin be held at ground potential.
5. The Auto-Track function is disabled by connecting the Track pin to the input voltage (VI). When Auto-Track is
disabled, the output voltage rises at a quicker and more linear rate after input power has been applied.
17
PTH12060W/L
www.ti.com
SLTS217D – MAY 2003 – REVISED OCTOBER 2005
2
U1
Track
VI = 12 V
3
+
VI
PTH12050W
Inhibit
GND
4
1
Vo 1 = 3.3 V
6
VO
Adjust
5
CI1
+
RSET1
CO1
2.0 kΩ
8
U3
7
2
1
3
VCC
SENSE
RESET
5
RTRK #
RESIN
TL7712A
REF
RESET
50 Ω
0.1 µF
9
Up Dn
8
5
Track
Sense
CT
2
GND
CREF
10
U2
6
CT
3.3 µF
4
PTH12060W
VI
VO
Vo 2 = 1.8 V
6
RRST
10 kΩ
Inhibit
+
# RTRK = 100 Ω / N
N = Number of Track pins connected together
3
Adjust
GND
1
C I2
7
4
RSET2
+
CO2
11.5 kΩ
Figure 14. Sequenced Power Up and Power Down Using Auto-Track
VTRK (1 V/div)
V01 (1 V/div)
V01 (1 V/div)
V02 (1 V/div)
V02 (1 V/div)
t − Time − 20 ms/div
Figure 15. Simultaneous Power Up With Auto-Track
Control
18
VTRK (1 V/div)
t − Time − 400 µs/div
Figure 16. Simultaneous Power Down with Auto-Track
Control
PTH12060W/L
www.ti.com
SLTS217D – MAY 2003 – REVISED OCTOBER 2005
Margin Up/Down Controls
The PTH12060, PTH12010, PTH12020, and PTH12030 products incorporate Margin Up and Margin Down
control inputs. These controls allow the output voltage to be momentarily adjusted [1], either up or down, by a
nominal 5%. This provides a convenient method for dynamically testing the operation of the load circuit over its
supply margin or range. It can also be used to verify the function of supply voltage supervisors. The ±5% change
is applied to the adjusted output voltage, as set by the external resistor, RSET at the VO Adjust pin.
The 5% adjustment is made by pulling the appropriate margin control input directly to the GND terminal [2]. A
low-leakage, open-drain device, such as an n-channel MOSFET or p-channel JFET is recommended for this
purpose [3]. Adjustments of less than 5% can also be accommodated by adding series resistors to the control
inputs. The value of the resistor can be selected from Table 6, or calculated using Equation 2.
Up/Down Adjust Resistance Calculation
To reduce the margin adjustment to a value less than 5%, series resistors are required (See RD and RU in
Figure 17). For the same amount of adjustment, the resistor value calculated for RU and RD is the same. The
formula is as follows.
RU or RD =
499
- 99.8 kW
D%
(2)
Where ∆% = The desired amount of margin adjust in percent.
Notes:
1. The Margin Up and Margin Down controls were not intended to be activated simultaneously. If they are
activated simultaneously, the affect on the output voltage may not completely cancel, resulting in the
possibility of a slightly higher error in the output voltage set point.
2. The ground reference should be a direct connection to the module GND. This produces a more accurate
adjustment at the load circuit terminals. The transistors Q1 and Q2 should be located close to the regulator.
3. The Margin Up and Margin Down control inputs are not compatible with devices that source voltage. This
includes TTL logic. These are analog inputs and should only be controlled with a true open-drain device
(preferably a discrete MOSFET transistor). The device selected should have low off-state leakage current.
Each input sources 8 µA when grounded, and has an open-circuit voltage of 0.8 V.
Table 6. Margin Up/Down Resistor Values
% Adjust
RU / RD
5
0.0 kΩ
4
24.9 kΩ
3
66.5 kΩ
2
150.0 kΩ
1
397.0 kΩ
19
PTH12060W/L
www.ti.com
SLTS217D – MAY 2003 – REVISED OCTOBER 2005
1
10 9
8
7
0V
PT H12010W
(Top View)
VI
3
RD
RU
CI
+VO
6
2
+
+VO
4
5
RSET
0.1 W, 1%
+
L
O
A
D
CO
Q1
Margin Down
Q2
Margin Up
GND
GND
Figure 17. Margin Up/Down Application Schematic
20
PTH12060W/L
www.ti.com
SLTS217D – MAY 2003 – REVISED OCTOBER 2005
Prebias Startup Capability
The capability to start up into an output prebias condition is now available to all the 12-V input, PTH series of
power modules. (Note that this is a feature enhancement for the many of the W-suffix products) [1].
A prebias startup condition occurs as a result of an external voltage being present at the output of a power
module prior to its output becoming active. This often occurs in complex digital systems when current from
another power source is backfed through a dual-supply logic component, such as an FPGA or ASIC. Another
path might be via clamp diodes, sometimes used as part of a dual-supply power-up sequencing arrangement. A
prebias can cause problems with power modules that incorporate synchronous rectifiers. This is because under
most operating conditions, such modules can sink as well as source output current. The 12-V input PTH modules
all incorporate synchronous rectifiers, but does not sink current during startup, or whenever the Inhibit pin is held
low. Startup includes an initial delay (approximately 8ms–15 ms), followed by the rise of the output voltage under
the control of the module's internal soft-start mechanism; see Figure 18.
Conditions for Prebias Holdoff
In order for the module to allow an output prebias voltage to exist (and not sink current), certain conditions must
be maintained. The module holds off a prebias voltage when the Inhibit pin is held low, and whenever the output
is allowed to rise under soft-start control. Power up under soft-start control occurs upon the removal of the
ground signal to the Inhibit pin (with input voltage applied), or when input power is applied with Auto-Track
disabled [2]. To further ensure that the regulator doesn’t sink output current, (even with a ground signal applied to
its Inhibit), the input voltage must always be greater than the applied prebias source. This condition must exist
throughout the power-up sequence [3].
The soft-start period is complete when the output begins rising above the prebias voltage. Once it is complete
the module functions as normal, and sinks current if a voltage higher than the nominal regulation value is applied
to its output.
Note: If a prebias condition is not present, the soft-start period is complete when the output voltage has risen
to either the set-point voltage, or the voltage applied at the module's Track control pin, whichever is lowest.
to its output.
Demonstration Circuit
Figure 19 shows the startup waveforms for the demonstration circuit shown in Figure 20. The initial rise in VO2 is
the prebias voltage, which is passed from the VCCIO to the VCORE voltage rail through the ASIC. Note that the
output current from the PTH12010L module (IO2) is negligible until its output voltage rises above the applied
prebias.
UVLO
Threshold
VI (5 V/Div)
VO (1 V/Div)
VO1 (1 V/Div)
VO2 (1 V/Div)
IO2 (5 A/Div)
Start up
Period
t - Time = 10 ms/Div
Figure 18. PTH12020W Startup
Figure 19. Prebias Startup Waveforms
21
PTH12060W/L
www.ti.com
SLTS217D – MAY 2003 – REVISED OCTOBER 2005
Notes:
1. Output prebias holdoff is an inherent feature to all PTH120x0L and PTV120x0W/L modules. It has now been
incorporated into all modules (including W-suffix modules with part numbers of the form PTH120x0W), with a
production lot date code of 0423 or later.
2. The prebias start-up feature is not compatible with Auto-Track. If the rise in the output is limited by the
voltage applied to the Track control pin, the output sinks current during the period that the track control
voltage is below that of the back-feeding source. For this reason, it is recommended that Auto-Track be
disabled when not being used. This is accomplished by connecting the Track pin to the input voltage, VI. This
raises the Track pin voltage well above the set-point voltage prior to the module’s start up, thereby, defeating
the Auto-Track feature.
3. To further ensure that the regulator's output does not sink current when power is first applied (even with a
ground signal applied to the Inhibit control pin), the input voltage must always be greater than the applied
prebias source. This condition must exist throughout the power-up sequence of the power system.
10 9
Up
VI = 12 V
2
VI
Sense
GND
7
1
C1
330 mF
10 9
R3
11 k0
TL7702B
8
7
R4
100 kW
C5
0.1 mF
PTH12010L
Inhibit
3
8
VCC
SENSE
5
RESET
2
RESIN
1
REF
6
RESET
3
CT
GND
4
R5
C6
10 k0
0.68 mF
VI
GND
7
1
6
Adjust
4
R1
2 kW
Tra ck
2
VO
PTH12020W
Inhibit
3
+
5
8
Dn Tra ck
VO1 = 3.3 V
+
C2
330 mF
5
Sense
VO
6
Vadj
4
VO2 = 1.8 V
+
IO2
R1
130 W
+
C3
330 mF
VC ORE
+ C4
330 mF
Figure 20. Application Circuit Demonstrating Prebias Startup
22
ASIC
VC CI O
PTH12060W/L
www.ti.com
SLTS217D – MAY 2003 – REVISED OCTOBER 2005
Remote Sense
Products with this feature incorporate an output voltage sense pin, VO Sense. A remote sense improves the load
regulation performance of the module by allowing it to compensate for any IR voltage drop between its output
and the load. An IR drop is caused by the high output current flowing through the small amount of pin and trace
resistance.
To use this feature simply connect the VO Sense pin to the VO node, close to the load circuit (see data sheet
standard application circuit). If a sense pin is left open-circuit, an internal low-value resistor (15-Ω or less)
connected between the pin and the output node, ensures the output remains in regulation.
With the sense pin connected, the difference between the voltage measured directly between the VO and GND
pins, and that measured from VO Sense to GND, is the amount of IR drop being compensated by the regulator.
This should be limited to a maximum of 0.3 V.
Note: The remote sense feature is not designed to compensate for the forward drop of nonlinear or
frequency dependent components that may be placed in series with the converter output. Examples include
OR-ing diodes, filter inductors, ferrite beads, and fuses. When these components are enclosed by the remote
sense connection, they are effectively placed inside the regulation control loop, which can adversely affect
the stability of the regulator.
23
PTH12060W/L
SLTS217D – MAY 2003 – REVISED OCTOBER 2005
TAPE AND REEL SPECIFICATIONS
24
www.ti.com
PTH12060W/L
www.ti.com
SLTS217D – MAY 2003 – REVISED OCTOBER 2005
TRAY SPECIFICATIONS
25
PACKAGE OPTION ADDENDUM
www.ti.com
26-Oct-2005
PACKAGING INFORMATION
Orderable Device
Status (1)
Package
Type
Package
Drawing
Pins Package Eco Plan (2)
Qty
PTH12060LAH
ACTIVE
DIP MOD
ULE
EUW
10
36
TBD
Call TI
Level-1-235C-UNLIM
PTH12060LAS
ACTIVE
DIP MOD
ULE
EUY
10
36
TBD
Call TI
Level-1-235C-UNLIM
PTH12060LAST
ACTIVE
DIP MOD
ULE
EUY
10
250
TBD
Call TI
Level-1-235C-UNLIM
PTH12060LAZ
ACTIVE
DIP MOD
ULE
EUY
10
36
Pb-Free
(RoHS)
Call TI
Level-3-260C-168 HR
PTH12060LAZT
ACTIVE
DIP MOD
ULE
EUY
10
250
Pb-Free
(RoHS)
Call TI
Level-3-260C-168 HR
PTH12060WAD
ACTIVE
DIP MOD
ULE
EUW
10
36
Pb-Free
(RoHS)
Call TI
Level-NC-NC-NC
PTH12060WAH
ACTIVE
DIP MOD
ULE
EUW
10
36
TBD
Call TI
Level-1-235C-UNLIM
PTH12060WAS
ACTIVE
DIP MOD
ULE
EUY
10
36
TBD
Call TI
Level-1-235C-UNLIM
PTH12060WAST
ACTIVE
DIP MOD
ULE
EUY
10
250
TBD
Call TI
Level-1-235C-UNLIM
PTH12060WAZ
ACTIVE
DIP MOD
ULE
EUY
10
36
Pb-Free
(RoHS)
Call TI
Level-3-260C-168 HR
PTH12060WAZT
ACTIVE
DIP MOD
ULE
EUY
10
250
Pb-Free
(RoHS)
Call TI
Level-3-260C-168 HR
Lead/Ball Finish
MSL Peak Temp (3)
(1)
The marketing status values are defined as follows:
ACTIVE: Product device recommended for new designs.
LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect.
NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in
a new design.
PREVIEW: Device has been announced but is not in production. Samples may or may not be available.
OBSOLETE: TI has discontinued the production of the device.
(2)
Eco Plan - The planned eco-friendly classification: Pb-Free (RoHS) or Green (RoHS & no Sb/Br) - please check
http://www.ti.com/productcontent for the latest availability information and additional product content details.
TBD: The Pb-Free/Green conversion plan has not been defined.
Pb-Free (RoHS): TI's terms "Lead-Free" or "Pb-Free" mean semiconductor products that are compatible with the current RoHS requirements
for all 6 substances, including the requirement that lead not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered
at high temperatures, TI Pb-Free products are suitable for use in specified lead-free processes.
Green (RoHS & no Sb/Br): TI defines "Green" to mean Pb-Free (RoHS compatible), and free of Bromine (Br) and Antimony (Sb) based flame
retardants (Br or Sb do not exceed 0.1% by weight in homogeneous material)
(3)
MSL, Peak Temp. -- The Moisture Sensitivity Level rating according to the JEDEC industry standard classifications, and peak solder
temperature.
Important Information and Disclaimer:The information provided on this page represents TI's knowledge and belief as of the date that it is
provided. TI bases its knowledge and belief on information provided by third parties, and makes no representation or warranty as to the
accuracy of such information. Efforts are underway to better integrate information from third parties. TI has taken and continues to take
reasonable steps to provide representative and accurate information but may not have conducted destructive testing or chemical analysis on
incoming materials and chemicals. TI and TI suppliers consider certain information to be proprietary, and thus CAS numbers and other limited
information may not be available for release.
In no event shall TI's liability arising out of such information exceed the total purchase price of the TI part(s) at issue in this document sold by TI
to Customer on an annual basis.
Addendum-Page 1
IMPORTANT NOTICE
Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, modifications,
enhancements, improvements, and other changes to its products and services at any time and to discontinue
any product or service without notice. Customers should obtain the latest relevant information before placing
orders and should verify that such information is current and complete. All products are sold subject to TI’s terms
and conditions of sale supplied at the time of order acknowledgment.
TI warrants performance of its hardware products to the specifications applicable at the time of sale in
accordance with TI’s standard warranty. Testing and other quality control techniques are used to the extent TI
deems necessary to support this warranty. Except where mandated by government requirements, testing of all
parameters of each product is not necessarily performed.
TI assumes no liability for applications assistance or customer product design. Customers are responsible for
their products and applications using TI components. To minimize the risks associated with customer products
and applications, customers should provide adequate design and operating safeguards.
TI does not warrant or represent that any license, either express or implied, is granted under any TI patent right,
copyright, mask work right, or other TI intellectual property right relating to any combination, machine, or process
in which TI products or services are used. Information published by TI regarding third-party products or services
does not constitute a license from TI to use such products or services or a warranty or endorsement thereof.
Use of such information may require a license from a third party under the patents or other intellectual property
of the third party, or a license from TI under the patents or other intellectual property of TI.
Reproduction of information in TI data books or data sheets is permissible only if reproduction is without
alteration and is accompanied by all associated warranties, conditions, limitations, and notices. Reproduction
of this information with alteration is an unfair and deceptive business practice. TI is not responsible or liable for
such altered documentation.
Resale of TI products or services with statements different from or beyond the parameters stated by TI for that
product or service voids all express and any implied warranties for the associated TI product or service and
is an unfair and deceptive business practice. TI is not responsible or liable for any such statements.
Following are URLs where you can obtain information on other Texas Instruments products and application
solutions:
Products
Applications
Amplifiers
amplifier.ti.com
Audio
www.ti.com/audio
Data Converters
dataconverter.ti.com
Automotive
www.ti.com/automotive
DSP
dsp.ti.com
Broadband
www.ti.com/broadband
Interface
interface.ti.com
Digital Control
www.ti.com/digitalcontrol
Logic
logic.ti.com
Military
www.ti.com/military
Power Mgmt
power.ti.com
Optical Networking
www.ti.com/opticalnetwork
Microcontrollers
microcontroller.ti.com
Security
www.ti.com/security
Telephony
www.ti.com/telephony
Video & Imaging
www.ti.com/video
Wireless
www.ti.com/wireless
Mailing Address:
Texas Instruments
Post Office Box 655303 Dallas, Texas 75265
Copyright  2005, Texas Instruments Incorporated