PTH03010W —3.3-V Input 15-A, 3.3-V Input Non-Isolated Wide-Output Adjust Power Module SLTS203C – MAY 2003 – REVISED DECEMBER 2003 Features NOMINAL SIZE = • Up to 15-A Output Current • 3.3-V Input Voltage • Wide-Output Voltage Adjust (0.8 V to 2.5 V) • Efficiencies up to 95 % • 125 W/in³ Power Density • On/Off Inhibit • Output Voltage Sense • Pre-Bias Startup • Output Over-Current Protection (Non-Latching, Auto-Reset) 1.37 in x 0.62 in (34,8 mm x 15,75 mm) • • • • • • Auto-Track™ Sequencing Margin Up/Down Controls Under-Voltage Lockout Operating Temp: –40 to +85 °C DSP Compatible Output Voltages Safety Agency Approvals: UL 1950, CSA 22.2 950, EN60950 VDE (Pending) • Point-of-load Alliance (POLA) Compatible Description Pin Configuration Auto-Track simplifies the task of supply voltage sequencing in a power system by enabling modules to track each other, or any external voltage, during power up and power down. Other operating features include an on/off inhibit, output voltage adjust (trim), and margin up/down controls. To ensure tight load regulation, an output voltage sense is also provided. A non-latching over-current trip serves as load fault protection. Target applications include complex multi-voltage, multi-processor systems that incorporate the industry’s high-speed DSPs, micro-processors and bus drivers. The PTH03010 series of non-isolated power modules are small in size but big on performance and flexibility. Their high output current, compact footprint, and industry-leading features offers system designers a versatile module for powering complex multi-processor digital systems. The series employs double-sided surface mount construction and provides highperformance step-down power conversion for up to 15 A of output current from a 3.3-V input bus voltage. The output voltage of the PTH03010W can be set to any value over the range, 0.8 V to 2.5 V, using a single resistor. This series includes Auto-Track™. Pin 1 2 3 4 5 6 7 8 9 10 Function GND Vin Inhibit * Vo Adjust Vo Sense Vout GND Track Margin Down * Margin Up * * Denotes negative logic: Open = Normal operation Ground = Function active ™ Track Auto- n c i n g e Sequ Standard Application Track Rset = Required to set the output voltage to a value higher than 0.8 V. (See spec. table for values) Cin = Required 470 µF capacitor Cout = Optional 330 µF Capacitor Margin Down Margin Up 1 10 9 8 7 PTH03010 (Top View) V IN 2 V OUT 6 3 4 5 V o Sense Inhibit + GND For technical support and more information, visit http://power.ti.com RSET (Required) 0.1 W, 1 % + CIN 470 µF (Required) COUT 330 µF (Optional) GND L O A D PTH03010W —3.3-V Input 15-A, 3.3-V Input Non-Isolated Wide-Output Adjust Power Module SLTS203C – MAY 2003 – REVISED DECEMBER 2003 Ordering Information Output Voltage (PTH03010Hxx) Package Options (PTH03010xHH) (1) Code W Code AH AS Voltage 0.8 V – 2.5 V (Adjust) Description Horiz. T/H SMD, Standard (3) Pkg Ref. (EUH) (EUJ) (2) Notes: (1) Add “T” to end of part number for tape and reel on SMD packages only. (2) Reference the applicable package reference drawing for the dimensions and PC board layout (3) “Standard” option specifies 63/37, Sn/Pb pin solder material. Pin Descriptions Vin: The positive input voltage power node to the module, which is referenced to common GND. Vout: The regulated positive power output with respect to the GND node. GND: This is the common ground connection for the Vin and Vout power connections. It is also the 0 VDC reference for the control inputs. Inhibit: The Inhibit pin is an open-collector/drain negative logic input that is referenced to GND. Applying a lowlevel ground signal to this input disables the module’s output and turns off the output voltage. When the Inhibit control is active, the input current drawn by the regulator is significantly reduced. If the Inhibit pin is left open-circuit, the module will produce an output whenever a valid input source is applied. Vo Adjust: A 0.1 W 1 % resistor must be directly connected between this pin and pin 7 (GND) to set the output voltage to a value higher than 0.8 V. The temperature stability of the resistor should be 100 ppm/°C (or better). The set point range for the output voltage is from 0.8 V to 2.5 V. The resistor value required for a given output voltage may be calculated from the following formula. If left open circuit, the output voltage will default to its lowest value. For further information on output voltage adjustment, consult the related application note. Rset 0.8 V = 10 k · Vout – 0.8 V – 2.49 k The specification table gives the preferred resistor values for a number of standard output voltages. Vo Sense: The sense input allows the regulation circuit to compensate for voltage drop between the module and the load. For optimal voltage accuracy Vo Sense should be connected to Vout. It can also be left disconnected. Track: This is an analog control input that enables the output voltage to follow an external voltage. This pin becomes active typically 20 ms after the input voltage has been applied, and allows direct control of the output voltage from 0 V up to the nominal set-point voltage. Within this range the output will follow the voltage at the Track pin on a volt-for-volt basis. When the control voltage is raised above this range, the module regulates at its set-point voltage. The feature allows the output voltage to rise simultaneously with other modules powered from the same input bus. If unused, this input should be connected to Vin. Note: Due to the under-voltage lockout feature, the output of the module cannot follow its own input voltage during power up. For more information, consult the related application note. Margin Down: When this input is asserted to GND, the output voltage is decreased by 5% from the nominal. The input requires an open-collector (open-drain) interface. It is not TTL compatible. A lower percent change can be accomodated with a series resistor. If unused, this input may be left unconnected. For further information, consult the related application note. Margin Up: When this input is asserted to GND, the output voltage is increased by 5%. The input requires an open-collector (open-drain) interface. It is not TTL compatible. The percent change can be reduced with a series resistor. If unused, this input may be left unconnected. For further information, consult the related application note. For technical support and more information, visit http://power.ti.com PTH03010W —3.3-V Input 15-A, 3.3-V Input Non-Isolated Wide-Output Adjust Power Module SLTS203C – MAY 2003 – REVISED DECEMBER 2003 Environmental & Absolute Maximum Ratings Characteristics Symbols Track Input Voltage Operating Temperature Range Solder Reflow Temperature Storage Temperature Mechanical Shock Vtrack Ta Treflow Ts Mechanical Vibration Weight Flammability — — (Voltages are with respect to GND) Conditions Over Vin Range Surface temperature of module body or pins — Per Mil-STD-883D, Method 2002.3 1 msec, ½ Sine, mounted Mil-STD-883D, Method 2007.2 20-2000 Hz Min Typ –0.3 –40 — — Max Units –40 — — 500 — 20 — G’s — 5 — grams Vin + 0.3 85 235 (i) 125 — V °C °C °C G’s Meets UL 94V-O Notes: (i) During reflow of SMD package version do not elevate peak temperature of the module, pins or internal components above the stated maximum. Specifications (Unless otherwise stated, Ta =25 °C, Vin =3.3 V, V out =2 V, C in =470 µF, C out =0 µF, and Io =Iomax) PTH03010W Characteristics Symbols Conditions Output Current Io 0.8 V ≤ Vo ≤ 2.5 V, Input Voltage Range Set-Point Voltage Tolerance Temperature Variation Line Regulation Load Regulation Total Output Variation Vin Vo tol ∆Regtemp ∆Regline ∆Regload ∆Regtot Over Io range Efficiency η Vo Ripple (pk-pk) Over-Current Threshold Transient Response Vr Io trip Margin Up/Down Adjust Margin Input Current (pins 9 /10) Track Input Current (pin 8) Track Slew Rate Capability Under-Voltage Lockout ttr ∆Vtr Vo adj IIL margin IIL track dVtrack/dt UVLO Inhibit Control (pin3) Input High Voltage Input Low Voltage Input Low Current Input Standby Current Switching Frequency External Input Capacitance External Output Capacitance VIH VIL IIL inhibit Iin inh ƒs Cin Cout Reliability MTBF 60 °C, 200 LFM airflow 25 °C, natural convection –40 °C <Ta < +85 °C Over Vin range Over Io range Includes set-point, line, load, –40 °C ≤ T a ≤ +85 °C Io =10 A RSET = 2.21 kΩ Vo = 2.5 V RSET = 4.12 kΩ Vo = 2.0 V RSET = 5.49 kΩ Vo = 1.8 V RSET = 8.87 kΩ Vo = 1.5 V RSET = 17.4 kΩ Vo = 1.2 V RSET = 36.5 kΩ Vo = 1.0 V 20 MHz bandwidth Reset, followed by auto-recovery 1 A/µs load step, 50 to 100 % Iomax, Cout =330 µF Recovery Time Vo over/undershoot Pin to GND Pin to GND Cout ≤ Cout(max) Vin increasing Vin decreasing Referenced to GND Pin to GND Inhibit (pin 3) to GND, Track (pin 8) open Over Vin and Io ranges Capacitance Value non-ceramic ceramic Equiv. series resistance (non-ceramic) Per Bellcore TR-332 50 % stress, Ta =40 °C, ground benign Min Typ Max Units 0 0 2.95 — — — — — — — — — ±0.5 ±10 ±12 — 15 (1) 15 (1) 3.65 ±2 (3) — — — ±3 (3) A — — — — — — — — 93 92 91 89 87 85 20 27.5 — — — — — — — — — — — — — — — 2.2 70 100 ±5 – 8 (4) — — 2.45 2.5 — — — — –130 1 2.8 — Vin –0.5 –0.2 — — 275 470 (6) 0 0 (9) 4 — — –130 10 300 — 330 (7) — — Open 0.8 — — 325 — 8,250 300 — 5.7 — — (2) V %Vo %Vo mV mV %Vo % mVpp A (5) (5) µSec mV % µA µA V/ms V V µA mA kHz µF (8) µF mΩ 106 Hrs Notes: (1) See SOA curves or consult factory for appropriate derating. (2) The minimum input voltage is equal to 2.95 V or Vout + 0.65 V, whichever is greater. (3) The set-point voltage tolerance is affected by the tolerance and stability of RSET. The stated limit is unconditionally met if R SET has a tolerance of 1 % with 100 ppm/°C or better temperature stability. (4) A small low-leakage (<100 nA) MOSFET is recommended to control this pin. The open-circuit voltage is less than 1 Vdc. (5) This control pin has an internal pull-up to the input voltage Vin. If it is left open-circuit the module will operate when input power is applied. A small low-leakage (<100 nA) MOSFET is recommended for control. For further information, consult the related application note. (6) A 470-µF electrolytic input capacitor is required for proper operation. The capacitor must be rated for a minimum of 700 mArms of ripple current. (7) An external output capacitor is not required for basic operation. Adding 330 µF of distributed capacitance at the load will improve the transient response. (8) This is the calculated maximum. The minimum ESR limitation will often result in a lower value. Consult the application notes for further guidance. (9) This is the typical ESR for all the electrolytic (non-ceramic) ouput capacitance. Use 7 mΩ as the minimum when using max-ESR values to calculate. For technical support and more information, visit http://power.ti.com PTH03010W —3.3-V Input Typical Characteristics 15-A, 3.3-V Input Non-Isolated Wide-Output Adjust Power Module SLTS203C – MAY 2003 – REVISED DECEMBER 2003 Characteristic Data; Vin =3.3V Safe Operating Area; Vin =3.3 V (See Note A) Efficiency vs Load Current (See Note B) Output Voltage =2.5 V 100 90 Efficiency - % VOUT 2.5 V 2.0 V 1.8 V 1.5 V 1.2 V 1.0 V 80 70 60 Ambient Temperature (°C) 80 90 Airflow 70 400LFM 200LFM 100LFM Nat Conv 60 50 40 30 50 20 0 3 6 9 12 15 0 3 6 Iout - Amps 9 12 15 Iout (A) Output Ripple vs Load Current Output Voltage =1 V 50 90 Ripple - mV VOUT 1.8 V 1.5 V 2.0 V 1.2 V 1.0 V 2.5 V 30 20 10 Ambient Temperature (°C) 80 40 Airflow 70 400LFM 200LFM 100LFM Nat Conv 60 50 40 30 0 20 0 3 6 9 12 15 0 Iout - Amps 3 6 9 12 15 Iout (A) Power Dissipation vs Load Current 4 Pd - Watts 3 2 1 0 0 3 6 9 12 15 Iout - Amps Note A: Characteristic data has been developed from actual products tested at 25°C. This data is considered typical data for the converter. Note B: SOA curves represent the conditions at which internal components are at or below the manufacturer’s maximum operating temperatures. Derating limits apply to modules soldered directly to a 4 in. × 4 in. double-sided PCB with 1 oz. copper. For technical support and more information, visit http://power.ti.com Application Notes PTH03010W & PTH05010W Capacitor Recommendations for the PTH03010 & PTH05010 Series of Power Modules Input Capacitor The recommended input capacitor(s) is determined by the 470 µF minimum capacitance and 700 mArms minimum ripple current rating. Ripple current, less than 100 mΩ equivalent series resistance (ESR), and temperature are the major considerations when selecting input capacitors. Unlike polymer tantalum, regular tantalum capacitors have a recommended minimum voltage rating of 2 × (maximum DC voltage + AC ripple). This is standard practice to ensure reliability. For improved ripple reduction on the input bus, ceramic capacitors [1] may used to complement electrolytic types to achieve the minimum required capacitance. Output Capacitors (Optional) For applications with load transients (sudden changes in load current), regulator response will benefit from an external output capacitance. The recommended output capacitance of 330 µF will allow the module to meet its transient response specification (see product data sheet). For most applications, a high quality computer-grade aluminum electrolytic capacitor is adequate. These capacitors provide decoupling over the frequency range, 2 kHz to 150 kHz, and are suitable for ambient temperatures above 0 °C. For operation below 0 °C tantalum, ceramic or Os-Con type capacitors are recommended. When using one or more non-ceramic capacitors, the calculated equivalent ESR should be no lower than 4 mΩ (7 mΩ using the manufacturer’s maximum ESR for a single capacitor). A list of preferred low-ESR type capacitors are identified in Table 1-1. Ceramic Capacitors Above 150 kHz the performance of aluminum electrolytic capacitors becomes less effective. To further improve the reflected input ripple [1] current or the output transient response, multilayer ceramic capacitors can also be added. Ceramic capacitors have very low ESR and their resonant frequency is higher than the bandwidth of the regulator. When used on the output their combined ESR is not critical as long as the total value of ceramic capacitance does not exceed 300 µF. Also, to prevent the formation of local resonances, do not place more than five identical ceramic capacitors in parallel with values of 10 µF or greater. Tantalum Capacitors Tantalum type capacitors can be used at both the input and output, and are recommended for applications where the ambient operating temperature can be less than 0 °C. The AVX TPS, Sprague 593D/594/595 and Kemet T495/ For technical support and more information, visit http://power.ti.com T510 capacitor series are suggested over many other tantalum types due to their higher rated surge, power dissipation, and ripple current capability. As a caution many general purpose tantalum capacitors have considerably higher ESR, reduced power dissipation and lower ripple current capability. These capacitors are also less reliable as they have lower power dissipation and surge current ratings. Tantalum capacitors that do not have a stated ESR or surge current rating are not recommended for power applications. When specifying Os-Con and polymer tantalum capacitors for the output, the minimum ESR limit will be encountered well before the maximum capacitance value is reached. Capacitor Table Table 1-1 identifies the characteristics of capacitors from a number of vendors with acceptable ESR and ripple current (rms) ratings. The recommended number of capacitors required at both the input and output buses is identified for each capacitor type. This is not an extensive capacitor list. Capacitors from other vendors are available with comparable specifications. Those listed are for guidance. The RMS ripple current rating and ESR (at 100 kHz) are critical parameters necessary to insure both optimum regulator performance and long capacitor life. Designing for Very Fast Load Transients The transient response of the DC/DC converter has been characterized using a load transient with a di/dt of 1 A/µs. The typical voltage deviation for this load transient is given in the data sheet specification table using the optional value of output capacitance. As the di/dt of a transient is increased, the response of a converter’s regulation circuit ultimately depends on its output capacitor decoupling network. This is an inherent limitation with any DC/DC converter once the speed of the transient exceeds its bandwidth capability. If the target application specifies a higher di/dt or lower voltage deviation, the requirement can only be met with additional output capacitor decoupling. In these cases special attention must be paid to the type, value and ESR of the capacitors selected. If the transient performance requirements exceed that specified in the data sheet, or the total amount of load capacitance is above 3,000 µF, the selection of output capacitors becomes more important. For further guidance consult the separate application note, “Selecting Output Capacitors for PTH Products in High-Performance Applications.” Application Notes PTH03010W & PTH05010W Table 1-1: Input/Output Capacitors Capacitor Vendor, Type/ Series (Style) Capacitor Characteristics Quantity Working Voltage Value (µF) Max. ESR at 100 kHz Max. Ripple Current at 85 °C (Irms) Physical Size (mm) Input Bus Output Bus Panasonic, Aluminum FC (Radial) FK (SMD) 10 V 16 V 25 V 560 470 470 0.090 Ω 0.090 Ω 0080 Ω 755 mA 755 mA 850 mA 10×12.5 10×12.5 10×10.2 1 1 1 1 1 1 United Chemi-con PXA, Poly-Aluminum (SMD) PS, Poly-Aluminum (Radial) FX, Os-con (Radial) LXZ, Aluminum (Radial) 6.3 V 10 V 10 V 16 V 470 470 680 470 0.020 Ω 0.012 Ω 0.015 Ω 0.090 Ω 4130 mA 5300 mA 4735 mA 760 mA 10×7.7 10×12.5 10×10.5 10×12.5 1 1 1 1 ≤4 ≤2 ≤3 1 Nichicon, Aluminum WG (SMD) HD (Radiall) PM (Radial) 10 V 16 V 16 V 470 470 470 0.150÷2 Ω 0.090 Ω 1030 Ω 670 mA x 2 770 mA 1030 mA 10×10 10×15 10×12.5 2 1 1 1 1 1 Panasonic, Poly-Aluminum: WA (SMD) S/SE (SMD) 10 V 6.3 V 470 180 0.017 Ω 0.005 Ω 4500 mA 4000 mA 10×10.2 7.3×4.3×4.2 1 3 ≤3 ≤1 EEFWA1A471P EEFSE0J181R Sanyo SP, Os-con (Radial) SVP, Os-con (SMD) TPE, Poscap (SMD) 10 V 10 V 6.3 V 470 560 470 0.015 Ω 0.013 Ω 0.018 Ω 4500 mA 5200 mA 3500 mA 10×10.5 11×12.7 7.3×4.3 1 1 1 ≤2 ≤2 ≤3 10SP470M 10SVP560M 6TPE470MI AVX Tantalum TPS SMD) 10 V 10 V 470 470 0.045 Ω 0.060 Ω 1723 mA 1826 mA 7.3L ×5.7W ×4.1H 1 1 ≤5 ≤5 TPSE477M010R0045 TPSV477M010R0060 Kemet, Poly-Tantalum T520, (SMD) T530. (SMD) 10 V 10 V 330 330 0.040 Ω 0.015 Ω 1800 mA >3800 mA 4.3W ×7.3L ×4.0H 2 2 ≤5 ≤2 T520X337M010AS T530X337M010AS 10 V 10V 6.3 V 470 470 470 0.100 Ω 0.015 Ω 0.017 Ω 1440 mA 4510 mA 3960 mA 7.2L×6W 10 × 10 8 × 12 1 1 1 ≤5 ≤2 ≤3 595D477X0010R2T 94SP477X0010FBP 94SVP477X06R3E12 Kemet, Ceramic X5R (SMD) 16 V 6.3 V 10 47 0.002 Ω — 1210 case 3225 mm 1 1 ≤5 ≤5 C1210C106M4PAC C1210C476K9PAC Murata, Ceramic X5R (SMD) 6.3 V 6.3 V 16 V 16 V 100 47 22 10 0.002 Ω — 1210 case 3225 mm 1 [1] 1 [1] 1 [1] 1 [1] ≤3 ≤5 ≤5 ≤5 GRM32ER60J107M GRM32ER60J476M GRM32ER61C226K GRM32DR61C106K TDK, Ceramic X5R (SMD) 6.3 V 6.3 V 16 V 16 V 100 47 22 10 0.002 Ω — 1210 case 3225 mm 1 [1] 1 [1] 1 [1] 1 [1] ≤3 ≤5 ≤5 ≤5 C3225X5R0J107MT C3225X5R0J476MT C3225X5R1C226MT C3225X5R1C106MT Vishay-Sprague 595D, Tantalum (SMD) 94SP Poly-Aluminum (Radial) 94SVP Poly-Aluminum SMD) Vendor Part Number EEUFC1A561 EEUFC1C471 EEVFK1E471P PXA6.3VC471MJ80TP 10PS470MJ12 10FX680M LXZ16VB471M10X12LL UWG1A471MNR1GS UPM1C 471MPH6 UHD1C471MPR [1] A ceramic capacitor may be used to complement electrolytic types at the input to further reduce high-frequency ripple current. For technical support and more information, visit http://power.ti.com Application Notes PTH03010W & PTH05010W Adjusting the Output Voltage of the PTH03010W & PTH05010W Wide-Output Adjust Power Modules The Vo Adjust control (pin 4) sets the output voltage of the PTH03010W and PTH05010W products. The adjustment range of the PT03010W (3.3-V input) is from 0.8 V to 2.5 V 1, and the PTH05010W (5-V input) from 0.8 V to 3.6 V. The adjustment method requires the addition of a single external resistor, Rset, that must be connected directly between the Vo Adjust and GND pins 2. Table 2-1 gives the preferred value of the external resistor for a number of standard voltages, along with the actual output voltage that this resistance value provides. For other output voltages the value of the required resistor can either be calculated using the following formula, or simply selected from the range of values given in Table 2-2. Figure 2-1 shows the placement of the required resistor. Rset = 10 kΩ · 0.8 V Vout – 0.8 V – 2.49 kΩ Table 2-1; Preferred Values of Rset for Standard Output Voltages Vout (Standard) Rset (Pref’d Value) 3.3 V 1 2.5 V 2V 1.8 V 1.5 V 1.2 V 1V 0.8 V 698 Ω 2.21 kΩ 4.12 kΩ 5.49 kΩ 8.87 kΩ 17.4 kΩ 36.5 kΩ Open Vout (Actual) 3.309V 2.502 V 2.010 V 1.803 V 1.504 V 1.202 V 1.005 V 0.8 V Figure 2-1; Vo Adjust Resistor Placement VO Sense [Note 3] 10 9 8 PTH05010W 7 VOUT VOUT 6 VO Adj 4 RSET 0.1 W, 1 % 0.800 0.825 0.850 0.875 0.900 0.925 0.950 0.975 1.000 1.025 1.050 1.075 1.100 1.125 1.150 1.175 1.200 1.225 1.250 1.275 1.300 1.325 1.350 1.375 1.400 1.425 1.450 1.475 1.50 1.55 1.60 1.65 1.70 1.75 1.80 1.85 1.90 1.95 Rset Open 318 kΩ 158 kΩ 104 kΩ 77.5 kΩ 61.5 kΩ 50.8 kΩ 43.2 kΩ 37.5 kΩ 33.1 kΩ 29.5 kΩ 26.6 kΩ 24.2 kΩ 22.1 kΩ 20.4 kΩ 18.8 kΩ 17.5 kΩ 16.3 kΩ 15.3 kΩ 14.4 kΩ 13.5 kΩ 12.7 kΩ 12.1 kΩ 11.4 kΩ 10.8 kΩ 10.3 kΩ 9.82 kΩ 9.36 kΩ 8.94 kΩ 8.18 kΩ 7.51 kΩ 6.92 kΩ 6.4 kΩ 5.93 kΩ 5.51 kΩ 5.13 kΩ 4.78 kΩ 4.47 kΩ Va Req’d 2.00 2.05 2.10 2.15 2.20 2.25 2.30 2.35 2.40 2.45 2.50 2.55 2.60 2.65 2.70 2.75 2.80 2.85 2.90 2.95 3.00 3.05 3.10 3.15 3.20 3.25 3.30 3.35 3.40 3.45 3.50 3.55 3.60 Rset 4.18 kΩ 3.91 kΩ 3.66 kΩ 3.44 kΩ 3.22 kΩ 3.03 kΩ 2.84 kΩ 2.67 kΩ 2.51 kΩ 2.36 kΩ 2.22 kΩ 2.08 kΩ 1.95 kΩ 1.83 kΩ 1.72 kΩ 1.61 kΩ 1.51 kΩ 1.41 kΩ 1.32 kΩ 1.23 kΩ 1.15 kΩ 1.07 kΩ 988 Ω 914 Ω 843 Ω 775 Ω 710 Ω 647 Ω 587 Ω 529 Ω 473 Ω 419 Ω 367 Ω COUT 330µF GND For technical support and more information, visit http://power.ti.com Notes: 1. Modules that operate from a 3.3-V input bus should not be adjusted higher than 2.5 V. 2. Use a 0.1 W resistor. The tolerance should be 1 %, with temperature stability of 100 ppm/°C (or better). Place the resistor as close to the regulator as possible. Connect the resistor directly between pins 4 and 7 using dedicated PCB traces. + GND 1 Va Req’d 5 VO Sense GND Table 2-2; Output Voltage Set-Point Resistor Values 3. Never connect capacitors from Vo Adjust to either GND or Vout. Any capacitance added to the Vo Adjust pin will affect the stability of the regulator. Application Notes PTH Series of Wide-Output Adjust Power Modules (3.3/5-V Input) Point-of-Load Alliance The PTH family of non-isolated, wide-output adjust power modules from Texas Instruments are optimized for applications that require a flexible, high performance module that is small in size. These products are part of the “Point-of-Load Alliance” (POLA), which ensures compatible footprint, interoperability and true second sourcing for customer design flexibility. The POLA is a collaboration between Texas Instruments, Artesyn Technologies, and Astec Power to offer customers advanced non-isolated modules that provide the same functionality and form factor. Product series covered by the alliance includes the PTHxx050W (6 A), PTHxx060W (10 A), PTHxx010W (15/12 A), PTHxx020W (22/18 A), and the PTHxx030W (30/26 A). From the basic, “Just Plug it In” functionality of the 6-A modules, to the 30-A rated feature-rich PTHxx030W, these products were designed to be very flexible, yet simple to use. The features vary with each product. Table 3-1 provides a quick reference to the available features by product and input bus voltage. output current, PTHxx020W and PTHxx030W products incorporate over-temperature shutdown protection. All of the products referenced in Table 3-1 include AutoTrack™. This is a feature unique to the PTH family, and was specifically designed to simplify the task of sequencing the supply voltage in a power system. These and other features are described in the following sections. Soft-Start Power Up The Auto-Track feature allows the power-up of multiple PTH modules to be directly controlled from the Track pin. However in a stand-alone configuration, or when the Auto-Track feature is not being used, the Track pin should be directly connected to the input voltage, Vin (see Figure 3-1). Figure 3–1 10 Up 5V 2 Inhibit 3 12 V 8A 3.3 V / 5 V 15 A 12 V 12 A 3.3 V / 5 V 22 A 12 V 18 A 3.3 V / 5 V 30 A 12 V 26 A Pre-Bias Startup • • • • • • Thermal Shutdown 10 A • • • • • • • • • • Output Sense PTHxx030 6A 3.3 V / 5 V • • • • • • • • • • Margin Up/Down PTHxx020 12 V • • • • • • • • • • Auto-Track™ PTHxx010 6A Over-Current PTHxx060 I OUT On/Off Inhibit PTHxx050 Input Bus 3.3 V / 5 V Adjust (Trim) + Series • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • CIN 1,000 µF 8 5 Track Sense PTH05020W V IN Table 3-1; Operating Features by Series and Input Bus Voltage 9 Dn 3.3 V 6 Adjust GND 1 VO 7 4 R SET, 698 Ω 0.1 W, 1 % + Features of the PTH Family of Non-Isolated Wide Output Adjust Power Modules C OUT 330 µF GND GND When the Track pin is connected to the input voltage the Auto-Track function is permanently disengaged. This allows the module to power up entirely under the control of its internal soft-start circuitry. When power up is under soft-start control, the output voltage rises to the set-point at a quicker and more linear rate. Figure 3–2 Vin (1 V/Div) Vout (1 V/Div) For simple point-of-use applications, the PTHxx050W provides operating features such as an on/off inhibit, output voltage trim, pre-bias startup (3.3/5-V input only), and over-current protection. The PTHxx060W (10 A), and PTHxx010W (15/12 A) include an output voltage sense, and margin up/down controls. Then the higher Iin (5 A/Div) HORIZ SCALE: 5 ms/Div For technical support and further information visit http://power.ti.com Application Notes PTH Series of Wide-Output Adjust Power Modules (3.3/5-V Input) The power modules function normally when the Inhibit pin is left open-circuit, providing a regulated output whenever a valid source voltage is connected to Vin with respect to GND. Figure 3-3 shows the typical application of the inhibit function. Note the discrete transistor (Q1). The Inhibit control has its own internal pull-up to Vin potential. The input is not compatible with TTL logic devices. An opencollector (or open-drain) discrete transistor is recommended for control. Figure 3–3 V o Sense Over-Current Protection Over-Temperature Protection The PTHxx020 and PTHxx030 series of products have over-temperature protection. These products have an on-board temperature sensor that protects the module’s internal circuitry against excessively high temperatures. A rise in the internal temperature may be the result of a drop in airflow, or a high ambient temperature. If the internal temperature exceeds the OTP threshold, the module’s Inhibit control is automatically pulled low. This turns the output off. The output voltage will drop as the external output capacitors are discharged by the load circuit. The recovery is automatic, and begins with a soft-start power up. It occurs when the the sensed temperature decreases by about 10 °C below the trip point. 10 VIN 2 8 5 1 7 Q1 BSS138 VOUT 6 4 RSET COUT 330 µF L O A D 1 =Inhibit GND GND Turning Q1 on applies a low voltage to the Inhibit control and disables the output of the module. If Q1 is then turned off, the module will execute a soft-start power-up. A regulated output voltage is produced within 20 msec. Figure 3-4 shows the typical rise in both the output voltage and input current, following the turn-off of Q1. The turn off of Q1 corresponds to the rise in the waveform, Q1 Vds. The waveforms were measured with a 5-A load. Figure 3–4 Note: The over-temperature protection is a last resort mechanism to prevent thermal stress to the regulator. Operation at or close to the thermal shutdown temperature is not recommended and will reduce the long-term reliability of the module. Always operate the regulator within the specified Safe Operating Area (SOA) limits for the worst-case conditions of ambient temperature and airflow. Vo (2V/Div) Iin (2A/Div) Output On/Off Inhibit For applications requiring output voltage on/off control, each series of the PTH family incorporates an output Inhibit control pin. The inhibit feature can be used wherever there is a requirement for the output voltage from the regulator to be turned off. 9 PTH05020W 3 CIN 1,000 µF + For protection against load faults, all modules incorporate output over-current protection. Applying a load that exceeds the regulator’s over-current threshold will cause the regulated output to shut down. Following shutdown a module will periodically attempt to recover by initiating a soft-start power-up. This is described as a “hiccup” mode of operation, whereby the module continues in a cycle of successive shutdown and power up until the load fault is removed. During this period, the average current flowing into the fault is significantly reduced. Once the fault is removed, the module automatically recovers and returns to normal operation. + From the moment a valid input voltage is applied, the soft-start control introduces a short time delay (typically 5 ms-10 ms) before allowing the output voltage to rise. The output then progressively rises to the module’s setpoint voltage. Figure 3-2 shows the soft-start power-up characteristic of the 22-A output product (PTH05020W), operating from a 5-V input bus and configured for a 3.3-V output. The waveforms were measured with a 5-A resistive load, with Auto-Track disabled. The initial rise in input current when the input voltage first starts to rise is the charge current drawn by the input capacitors. Power-up is complete within 15 ms. Q1Vds (5V/Div) HORIZ SCALE: 10ms/Div For technical support and further information visit http://power.ti.com Application Notes PTH Series of Wide-Output Adjust Power Modules (3.3/5-V Input) Auto-Track™ Function The Auto-Track function is unique to the PTH family, and is available with the all “Point-of-Load Alliance” (POLA) products. Auto-Track was designed to simplify the amount of circuitry required to make the output voltage from each module power up and power down in sequence. The sequencing of two or more supply voltages during power up is a common requirement for complex mixed-signal applications, that use dual-voltage VLSI ICs such as DSPs, micro-processors, and ASICs. How Auto-Track Works Auto-Track works by forcing the module’s output voltage to follow a voltage presented at the Track control pin. This control range is limited to between 0 V and the module’s set-point voltage. Once the track-pin voltage is raised above the set-point voltage, the module’s output remains at its set-point 1. As an example, if the Track pin of a 2.5-V regulator is at 1 V, the regulated output will be 1 V. But if the voltage at the Track pin rises to 3 V, the regulated output will not go higher than 2.5 V. When under track control, the regulated output from the module follows the voltage at its Track pin on a voltfor-volt basis. By connecting the Track pin of a number of these modules together, the output voltages will follow a common signal during power-up and power-down. The control signal can be an externally generated master ramp waveform, or the output voltage from another power supply circuit 3. For convenience the Track control incorporates an internal RC charge circuit. This operates off the module’s input voltage to provide a suitable rising voltage ramp waveform. Typical Application The basic implementation of Auto-Track allows for simultaneous voltage sequencing of a number of AutoTrack compliant modules. Connecting the Track control pins of two or more modules forces the Track control of all modules to follow the same collective RC ramp waveform, and allows them to be controlled through a single transistor or switch; Q1 in Figure 3-5. To initiate a power-up sequence the Track control must first pulled to ground potential. This should be done at or before input power is applied to the modules, and then held for at least 10 ms thereafter. This brief period gives the modules time to complete their internal soft-start initialization, which enables them to produce an output voltage. Applying a logic-level high signal to the circuit’s On/Off Control turns Q1 on and applies a ground signal to the Track control. After completing their internal soft-start intialization, the output of all modules will remain at zero volts while Q1 is on. 10 ms after a valid input voltage has been applied to all modules, Q1 can be turned off. This allows the track control voltage to automatically rise toward to the modules' input voltage. During this period the output voltage of each module will rise in unison with For technical support and further information visit http://power.ti.com other modules, to its respective set-point voltage. Figure 3-6 shows the output voltage waveforms from the circuit of Figure 3-5 after the On/Off Control is set from a high to a low-level voltage. The waveforms, Vo1 and Vo2 represent the output voltages from the two power modules, U1 (3.3 V) and U2 (1.8 V) respectively. Vo1 and Vo2 are shown rising together to produce the desired simultaneous power-up characteristic. The same circuit also provides a power-down sequence. Power down is the reverse of power up, and is accomplished by lowering the track control voltage back to zero volts. The important constraint is that a valid input voltage must be maintained until the power down is complete. It also requires that Q1 be turned off relatively slowly. This is so that the Track control voltage does not fall faster than Auto-Track's slew rate capability, which is 1 V/ms. The components R1 and C1 in Figure 3-5 limit the rate at which Q1 can pull down the Track control voltage. The values of 100 k-ohm and 0.1 µF correlate to a decay rate of about 0.17 V/ms. The power-down sequence is initiated with a low-to-high transition at the On/Off Control input to the circuit. Figure 3-7 shows the power-down waveforms. As the Track control voltage falls below the nominal set-point voltage of each power module, then its output voltage decays with all the other modules under Auto-Track control. Notes on Use of Auto-Track™ 1. The Track pin voltage must be allowed to rise above the module’s set-point voltage before the module can regulate at its adjusted set-point voltage. 2. The Auto-Track function will track almost any voltage ramp during power up, and is compatible with ramp speeds of up to 1 V/ms. 3. The absolute maximum voltage that may be applied to the Track pin is Vin. 4. The module will not follow a voltage at its Track control input until it has completed its soft-start initialization. This takes about 10 ms from the time that the module has sensed that a valid voltage has been applied its input. During this period, it is recommended that the Track pin be held at ground potential. 5. The module is capable of both sinking and sourcing current when following a voltage at its Track pin. Therefore startup into an output prebias is not supported during Auto-Track control. Note: A pre-bias holdoff is not necessary when all supply voltages rise simultaneously under the control of Auto-Track. 6. The Auto-Track function can be disabled by connecting the Track pin to the input voltage (Vin). With Auto-Track disabled, the output voltage will rise at a quicker and more linear rate after input power is applied. Application Notes PTH Series of Wide-Output Adjust Power Modules (3.3/5-V Input) Figure 3–5; Sequenced Power Up & Power Down Using Auto-Track U1 10 9 8 5 Track PTH05020W VIN Inhibit Vo1 =3.3 V 6 GND + 3 C IN VO 1 + 2 +5 V 4 7 C OUT R2 698 C1 0.1 µF U2 R1 100 k 9 8 5 Track 2 + C IN 0V Figure 3–6; Simultaneous Power Up with Auto-Track Control HORIZ SCALE: 10 ms/Div 10 Q1 BSS138 PTH05010W VIN Inhibit 3 VO Vo2 =1.8 V 6 GND 1 7 4 R3 5k49 + On/Off Control 1 = Power Down 0 = Power Up C OUT Figure 3–7; Simultaneous Power Down with Auto-Track Control Vo1 (1 V/Div) Vo1 (1 V/Div) Vo2 (1 V/Div) Vo2 (1 V/Div) On/Off Input (5 V/Div) On/Off Input (5 V/Div) HORIZ SCALE: 10 ms/Div For technical support and further information visit http://power.ti.com Application Notes PTH Series of Wide-Output Adjust Power Modules (3.3/5-V Input) Margin Up/Down Controls Notes: The PTHxx060W, PTHxx010W, PTHxx020W, and PTHxx030W products incorporate Margin Up and Margin Down control inputs. These controls allow the output voltage to be momentarily adjusted 1, either up or down, by a nominal 5 %. This provides a convenient method for dynamically testing the operation of the load circuit over its supply margin or range. It can also be used to verify the function of supply voltage supervisors. The ±5 % change is applied to the adjusted output voltage, as set by the external resistor, Rset at the Vo Adjust pin. The 5 % adjustment is made by pulling the appropriate margin control input directly to the GND terminal 2. A low-leakage open-drain device, such as an n-channel MOSFET or p-channel JFET is recommended for this purpose 3. Adjustments of less than 5 % can also be accommodated by adding series resistors to the control inputs. The value of the resistor can be selected from Table 3-2, or calculated using the following formula. Up/Down Adjust Resistance Calculation 1. The Margin Up* and Margin Dn* controls were not intended to be activated simultaneously. If they are their affects on the output voltage may not completely cancel, resulting in the possibility of a slightly higher error in the output voltage set point. 2. The ground reference should be a direct connection to the module GND at pin 7 (pin 1 for the PTHxx050). This will produce a more accurate adjustment at the load circuit terminals. The transistors Q1 and Q2 should be located close to the regulator. 3. The Margin Up and Margin Dn control inputs are not compatible with devices that source voltage. This includes TTL logic. These are analog inputs and should only be controlled with a true open-drain device (preferably a discrete MOSFET transistor). The device selected should have low off-state leakage current. Each input sources 8 µA when grounded, and has an open-circuit voltage of 0.8 V. To reduce the margin adjustment to something less than 5 %, series resistors are required (See RD and RU in Figure 3-8). For the same amount of adjustment, the resistor value calculated for RU and RD will be the same. The formulas is as follows. RU or RD = 499 ∆% – 99.8 Table 3-2; Margin Up/Down Resistor Values % Adjust 5 4 3 2 1 kΩ Where ∆% = The desired amount of margin adjust in percent. RU / RD 0.0 kΩ 24.9 kΩ 66.5 kΩ 150.0 kΩ 397.0 kΩ Figure 3–8; Margin Up/Down Application Schematic 10 9 8 1 7 0V PTH05010W (Top View) VIN 2 RD 4 5 RU RSET 0.1 W, 1 % Cin MargDn +VOUT 6 3 + +Vo + Cout L O A D Q1 MargUp GND For technical support and further information visit http://power.ti.com Q2 GND Application Notes PTH Series of Wide-Output Adjust Power Modules (3.3/5-V Input) Pre-Bias Startup Capability Notes Only selected products in the PTH family incorporate this capability. Consult Table 3-1 to identify which products are compliant. 1. Startup includes the short delay (approx. 10 ms) prior to the output voltage rising, followed by the rise of the output voltage under the module’s internal soft-start control. Startup is complete when the output voltage has risen to either the set-point voltage or the voltage at the Track pin, whichever is lowest. A pre-bias startup condition occurs as a result of an external voltage being present at the output of a power module prior to its output becoming active. This often occurs in complex digital systems when current from another power source is backfed through a dual-supply logic component, such as an FPGA or ASIC. Another path might be via clamp diodes as part of a dual-supply power-up sequencing arrangement. A prebias can cause problems with power modules that incorporate synchronous rectifiers. This is because under most operating conditions, these types of modules can sink as well as source output current. 2. To ensure that the regulator does not sink current when power is first applied (even with a ground signal applied to the Inhibit control pin), the input voltage must always be greater than the output voltage throughout the power-up and power-down sequence. 3. The Auto-Track function can be disabled at power up by immediately applying a voltage to the module’s Track pin that is greater than its set-point voltage. This can be easily accomplished by connecting the Track pin to Vin. The PTH family of power modules incorporate synchronous rectifiers, but will not sink current during startup 1, or whenever the Inhibit pin is held low. However, to ensure satisfactory operation of this function, certain conditions must be maintained. 2 Figure 3-9 shows an application demonstrating the pre-bias startup capability. The startup waveforms are shown in Figure 3-10. Note that the output current from the PTH03010W (Io) shows negligible current until its output voltage rises above that backfed through diodes D1 and D2. Figure 3–10; Pre-Bias Startup Waveforms Vin (1 V/Div) Vo (1 V/Div) Note: The pre-bias start-up feature is not compatible with Auto-Track. When the module is under Auto-Track control, it will sink current if the output voltage is below that of a back-feeding source. To ensure a pre-bias hold-off one of two approaches must be followed when input power is applied to the module. The Auto-Track function must either be disabled 3, or the module’s output held off (for at least 50 ms) using the Inhibit pin. Either approach ensures that the Track pin voltage is above the set-point voltage at start up. Io (5 A/Div) HORIZ SCALE: 5 ms/Div Figure 3–9; Application Circuit Demonstrating Pre-Bias Startup VIN = 3.3 V 10 2 3 CIN 330 µF 8 5 Track Sense PTH03010W V IN Inhibit + 9 GND 1 VO Vo = 2.5 V 6 + Vadj 7 Io 4 R2 2k21 VCCIO VCORE + C OUT 330 µF ASIC For technical support and further information visit http://power.ti.com Application Notes PTH Series of Wide-Output Adjust Power Modules (3.3/5-V Input) Remote Sense The PTHxx060W, PTHxx010W, PTHxx020W, and PTHxx030W products incorporate an output voltage sense pin, Vo Sense. The Vo Sense pin should be connected to Vout at the load circuit (see data sheet standard application). A remote sense improves the load regulation performance of the module by allowing it to compensate for any ‘IR’ voltage drop between itself and the load. An IR drop is caused by the high output current flowing through the small amount of pin and trace resistance. Use of the remote sense is optional. If not used, the V o Sense pin can be left open-circuit. An internal lowvalue resistor (15-Ω or less) is connected between the Vo Sense and Vout. This ensures the output voltage remains in regulation. With the sense pin connected, the difference between the voltage measured directly between the Vout and GND pins, and that measured from V o Sense to GND, is the amount of IR drop being compensated by the regulator. This should be limited to a maximum of 0.3 V. Note: The remote sense feature is not designed to compensate for the forward drop of non-linear or frequency dependent components that may be placed in series with the converter output. Examples include OR-ing diodes, filter inductors, ferrite beads, and fuses. When these components are enclosed by the remote sense connection they are effectively placed inside the regulation control loop, which can adversely affect the stability of the regulator. For technical support and further information visit http://power.ti.com PACKAGE OPTION ADDENDUM www.ti.com 18-Jul-2006 PACKAGING INFORMATION Orderable Device Status (1) Package Type Package Drawing Pins Package Eco Plan (2) Qty PTH03010WAD ACTIVE DIP MOD ULE EUH 10 25 Pb-Free (RoHS) Call TI N / A for Pkg Type PTH03010WAH ACTIVE DIP MOD ULE EUH 10 25 Pb-Free (RoHS) Call TI N / A for Pkg Type PTH03010WAS ACTIVE DIP MOD ULE EUJ 10 25 TBD Call TI Level-1-235C-UNLIM PTH03010WAST ACTIVE DIP MOD ULE EUJ 10 250 TBD Call TI Level-1-235C-UNLIM PTH03010WAZ ACTIVE DIP MOD ULE EUJ 10 25 Pb-Free (RoHS) Call TI Level-3-260C-168 HR PTH03010WAZT ACTIVE DIP MOD ULE EUJ 10 250 Pb-Free (RoHS) Call TI Level-3-260C-168 HR Lead/Ball Finish MSL Peak Temp (3) (1) The marketing status values are defined as follows: ACTIVE: Product device recommended for new designs. LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect. NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in a new design. PREVIEW: Device has been announced but is not in production. Samples may or may not be available. OBSOLETE: TI has discontinued the production of the device. (2) Eco Plan - The planned eco-friendly classification: Pb-Free (RoHS), Pb-Free (RoHS Exempt), or Green (RoHS & no Sb/Br) - please check http://www.ti.com/productcontent for the latest availability information and additional product content details. TBD: The Pb-Free/Green conversion plan has not been defined. Pb-Free (RoHS): TI's terms "Lead-Free" or "Pb-Free" mean semiconductor products that are compatible with the current RoHS requirements for all 6 substances, including the requirement that lead not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered at high temperatures, TI Pb-Free products are suitable for use in specified lead-free processes. Pb-Free (RoHS Exempt): This component has a RoHS exemption for either 1) lead-based flip-chip solder bumps used between the die and package, or 2) lead-based die adhesive used between the die and leadframe. The component is otherwise considered Pb-Free (RoHS compatible) as defined above. Green (RoHS & no Sb/Br): TI defines "Green" to mean Pb-Free (RoHS compatible), and free of Bromine (Br) and Antimony (Sb) based flame retardants (Br or Sb do not exceed 0.1% by weight in homogeneous material) (3) MSL, Peak Temp. -- The Moisture Sensitivity Level rating according to the JEDEC industry standard classifications, and peak solder temperature. Important Information and Disclaimer:The information provided on this page represents TI's knowledge and belief as of the date that it is provided. TI bases its knowledge and belief on information provided by third parties, and makes no representation or warranty as to the accuracy of such information. Efforts are underway to better integrate information from third parties. TI has taken and continues to take reasonable steps to provide representative and accurate information but may not have conducted destructive testing or chemical analysis on incoming materials and chemicals. TI and TI suppliers consider certain information to be proprietary, and thus CAS numbers and other limited information may not be available for release. In no event shall TI's liability arising out of such information exceed the total purchase price of the TI part(s) at issue in this document sold by TI to Customer on an annual basis. Addendum-Page 1 IMPORTANT NOTICE Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, modifications, enhancements, improvements, and other changes to its products and services at any time and to discontinue any product or service without notice. Customers should obtain the latest relevant information before placing orders and should verify that such information is current and complete. All products are sold subject to TI’s terms and conditions of sale supplied at the time of order acknowledgment. TI warrants performance of its hardware products to the specifications applicable at the time of sale in accordance with TI’s standard warranty. Testing and other quality control techniques are used to the extent TI deems necessary to support this warranty. Except where mandated by government requirements, testing of all parameters of each product is not necessarily performed. TI assumes no liability for applications assistance or customer product design. Customers are responsible for their products and applications using TI components. To minimize the risks associated with customer products and applications, customers should provide adequate design and operating safeguards. TI does not warrant or represent that any license, either express or implied, is granted under any TI patent right, copyright, mask work right, or other TI intellectual property right relating to any combination, machine, or process in which TI products or services are used. Information published by TI regarding third-party products or services does not constitute a license from TI to use such products or services or a warranty or endorsement thereof. Use of such information may require a license from a third party under the patents or other intellectual property of the third party, or a license from TI under the patents or other intellectual property of TI. Reproduction of information in TI data books or data sheets is permissible only if reproduction is without alteration and is accompanied by all associated warranties, conditions, limitations, and notices. Reproduction of this information with alteration is an unfair and deceptive business practice. TI is not responsible or liable for such altered documentation. Resale of TI products or services with statements different from or beyond the parameters stated by TI for that product or service voids all express and any implied warranties for the associated TI product or service and is an unfair and deceptive business practice. TI is not responsible or liable for any such statements. Following are URLs where you can obtain information on other Texas Instruments products and application solutions: Products Applications Amplifiers amplifier.ti.com Audio www.ti.com/audio Data Converters dataconverter.ti.com Automotive www.ti.com/automotive DSP dsp.ti.com Broadband www.ti.com/broadband Interface interface.ti.com Digital Control www.ti.com/digitalcontrol Logic logic.ti.com Military www.ti.com/military Power Mgmt power.ti.com Optical Networking www.ti.com/opticalnetwork Microcontrollers microcontroller.ti.com Security www.ti.com/security Low Power Wireless www.ti.com/lpw Mailing Address: Telephony www.ti.com/telephony Video & Imaging www.ti.com/video Wireless www.ti.com/wireless Texas Instruments Post Office Box 655303 Dallas, Texas 75265 Copyright 2006, Texas Instruments Incorporated