STMICROELECTRONICS T405-400T

T4 Series
®
4A TRIACS
SNUBBERLESS™ & LOGIC LEVEL
Table 1: Main Features
A2
Symbol
Value
Unit
IT(RMS)
4
A
VDRM/VRRM
600 to 800
V
IGT (Q1)
5 to 35
mA
G
A1
A2
A2
A1 A2
G
DESCRIPTION
Based on ST’s Snubberless / Logic level technology providing high commutation performances,
the T4 series is suitable for use on AC inductive
loads.
They are recommended for applications using
universal motors, electrovalves.... such as kitchen
aid equipments, power tools, dishwashers,...
Available in a fully insulated package, the T4......W version complies with UL standards (ref.
E81734).
A1
A2
G
DPAK
(T4-B)
IPAK
(T4-H)
A2
A1
A2
G
TO-220AB
(T4-T)
Table 2: Order Codes
Part Number
T405-xxxB
T405-xxxB-TR
T405-xxxH
T405-xxxT
T405-xxxW
T410-xxxB
T410-xxxB-TR
T410-xxxH
T4105-xxxT
T410-xxxW
T435-xxxB
T435-xxxB-TR
T435-xxxH
T435-xxxT
T435-xxxW
January 2006
REV. 7
A1
A2
G
ISOWATT220AB
(T4-W)
Marking
See page table 8 on
page 9
1/10
T4 Series
Table 3: Absolute Maximum Ratings
Symbol
IT(RMS)
ITSM
Parameter
IPAK/DPAK/
TO-220AB
RMS on-state current (full sine
wave)
Non repetitive surge peak on-state F = 50 Hz
current (full cycle, Tj initial = 25°C) F = 60 Hz
tp = 10 ms
dI/dt
Critical rate of rise of on-state current IG = 2 x IGT , tr ≤ 100 ns
F = 120 Hz
IGM
Peak gate current
tp = 20 µs
PG(AV)
Tstg
Tj
Unit
4
A
ISOWATT220AB Tc = 105°C
I²t Value for fusing
I²t
Tc = 110°C
Value
Average gate power dissipation
t = 20 ms
30
t = 16.7 ms
31
A
5.1
A ²s
Tj = 125°C
50
A/µs
Tj = 125°C
4
A
Tj = 125°C
1
W
- 40 to + 150
- 40 to + 125
°C
Storage junction temperature range
Operating junction temperature range
Tables 4: Electrical Characteristics (Tj = 25°C, unless otherwise specified)
Symbol
IGT (1)
VGT
Test Conditions
VD = 12 V RL = 30 Ω
VGD
VD = VDRM RL = 3.3 kΩ
Tj = 125°C
IH (2)
IT = 100 mA
IL
IG = 1.2 IGT
dV/dt (2)
(dI/dt)c (2) (dV/dt)c = 10 V/µs
Tj = 125°C
Tj = 125°C
Note 1: minimum IGT is guaranted at 5% of IGT max.
Note 2: for both polarities of A2 referenced to A1.
2/10
T435
5
10
35
Unit
I - II - III
MAX.
1.3
V
I - II - III
MIN.
0.2
V
II
Tj = 125°C
T410
MAX.
I - III
(dV/dt)c = 0.1 V/µs
T405
I - II - III
MAX.
VD = 67 %VDRM gate open
Tj = 125°C
Without snubber
T4
Quadrant
MAX.
MIN.
MIN.
10
15
35
10
25
50
15
30
60
20
40
400
1.8
2.7
-
0.9
2.0
-
-
-
2.5
mA
mA
mA
V/µs
A/ms
T4 Series
Table 5: Static Characteristics
Symbol
Test Conditions
VT (2)
ITM = 5.5 A
Vto (2)
tp = 380 µs
Value
Unit
Tj = 25°C
MAX.
1.56
V
Threshold voltage
Tj = 125°C
MAX.
0.89
V
Rd (2)
Dynamic resistance
Tj = 125°C
MAX.
120
mΩ
IDRM
IRRM
VDRM = VRRM
5
µA
1
mA
Tj = 25°C
Tj = 125°C
MAX.
Note 1: minimum IGT is guaranted at 5% of IGT max.
Note 2: for both polarities of A2 referenced to A1.
Table 6: Thermal resistance
Symbol
Rth(j-c)
Parameter
Junction to case (AC)
S = 0.5 cm²
Rth(j-a)
Junction to ambient
Value
IPAK / DPAK / TO-220AB
2.6
ISOWATT220AB
4.0
DPAK
70
TO-220AB / ISOWATT220AB
60
IPAK
100
Unit
°C/W
°C/W
S = Copper surface under tab.
3/10
T4 Series
Figure 1: Maximum power dissipation versus
RMS on-state current (full cycle)
Figure 2: RMS on-state current versus case
temperature (full cycle)
P(W)
IT(RMS)(A)
4.5
6
4.0
5
TO-220AB / DPAK / IPAK
3.5
3.0
4
ISOWATT220AB
2.5
3
2.0
1.5
2
1.0
1
0.5
IT(RMS)(A)
TC(°C)
0.0
0
0.0
0.5
1.0
1.5
2.0
2.5
3.0
3.5
0
4.0
Figure 3: RMS on-state current versus ambient
temperature (printed circuit board FR4, copper
thickness: 35µm) (full cycle)
25
50
75
100
125
Figure 4: Relative variation of thermal
impedance versus pulse duration
IT(RMS)(A)
K=[Zth/Rth]
2.0
1E+0
1.8
Rth(j-c)
DPAK
(S=0.5CM2)
1.6
ISOWATT220AB
Rth(j-a)
1.4
1.2
TO-220AB / DPAK / IPAK
1.0
1E-1
TO-220AB / ISOWATT220AB
0.8
DPAK / IPAK
0.6
0.4
0.2
tp(s)
TC(°C)
0.0
0
25
50
1E-2
75
100
1E-2
125
Figure 5: On-state characteristics (maximum
values)
1E-1
1E+0
1E+1
1E+2
5E+2
Figure 6: Surge peak on-state current versus
number of cycles
ITM(A)
ITSM(A)
30.0
35
Tj max.
Vto = 0.90V
Rd = 120 mΩ
10.0
30
t=20ms
25
One cycle
20
Non repetitive
Tj initial=25°C
Tj = Tj max.
15
1.0
Tj = 25°C.
Repetitive
TC=110°C
10
5
VTM(V)
Number of cycles
0
0.1
0.0
4/10
0.5
1.0
1.5
2.0
2.5
3.0
3.5
4.0
4.5
5.0
1
10
100
1000
T4 Series
Figure 7: Non-repetitive surge peak on-state
current for a sinusoidal pulse with width tp < 10 ms
and corresponding value of I2t
2
Figure 8: Relative variation of gate trigger
current, holding current and latching current
versus junction temperature (typical values)
IGT,IH,IL[Tj] / IGT,IH,IL[Tj=25°C]
2
ITSM(A), I t (A s)
2.5
500
Tj initial=25°C
2.0
dI/dt limitation:
50A/µs
100
IGT
ITSM
1.5
IH & IL
1.0
10
I2t
0.5
Tj(°C)
tp(ms)
0.0
1
0.01
0.10
1.00
-40
10.00
Figure 9: Relative variation of critical rate of
decrease of main current versus (dV/dt)c
(typical values)
-20
0
20
40
60
80
100
120
140
Figure 10: Relative variation of critical rate of
decrease of main current versus junction
temperature
(dI/dt)c [Tj] / (dI/dt)c [Tj specified]
(dI/dt)c [(dV/dt)c] / Specified (dI/dt)c
6
2.4
2.2
5
2.0
1.8
4
1.6
1.4
1.2
3
T435
1.0
0.8
2
T410
0.6
T405
0.4
1
0.2
(dV/dt)c (V/µs)
Tj(°C)
0.0
0
0.1
1.0
10.0
100.0
0
25
50
75
100
125
Figure 11: DPAK thermal resistance junction to
ambient versus copper surface under tab (printed
circuit board FR4, copper thickness: 35 µm)
Rth(j-a)(°C/W)
100
90
80
70
60
50
40
30
20
10
S(cm²)
0
0
4
8
12
16
20
24
28
32
36
40
5/10
T4 Series
Figure 12: Ordering Information Scheme
T 4 05 - 600 B (-TR)
Triac series
Current
4 = 4A
Sensitivity
05 = 5mA
10 = 10mA
35 = 35mA
Voltage
600 = 600V
700 = 700V
800 = 800V
Package
B = DPAK
H = IPAK
T = TO-220AB
W = ISOWATT220AB
Packing mode
Blank = Tube
-TR = Tape & reel
Table 7: Product Selector
Part Number
T405-xxxB
T405-xxxH
T405-xxxT
T405-xxxW
T410-xxxB
T410-xxxH
T410-xxxT
T410-xxxW
T435-xxxB
T435-xxxH
T435-xxxT
T435-xxxW
6/10
600 V
X
X
X
X
X
X
X
X
X
X
X
X
Voltage (xxx)
700 V
800 V
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
Sensitivity
5 mA
5 mA
5 mA
5 mA
10 mA
10 mA
10 mA
10 mA
35 mA
35 mA
35 mA
35 mA
Type
Package
Logic level
DPAK
Logic level
IPAK
Logic level
TO-220AB
Logic level ISOWATT220AB
Logic level
DPAK
Logic Level
IPAK
Logic Level
TO-220AB
Logic Level ISOWATT220AB
Snubberless
DPAK
Snubberless
IPAK
Snubberless
TO-220AB
Snubberless ISOWATT220AB
T4 Series
Figure 13: DPAK Package Mechanical Data
DIMENSIONS
REF.
E
A
B2
C2
L2
D
R
H
L4
A1
B
R
G
C
A2
0.60 MIN.
Inches
Min.
Max
Min.
Max.
A
2.20
2.40
0.086
0.094
A1
0.90
1.10
0.035
0.043
A2
0.03
0.23
0.001
0.009
B
0.64
0.90
0.025
0.035
B2
5.20
5.40
0.204
0.212
C
0.45
0.60
0.017
0.023
C2
0.48
0.60
0.018
0.023
D
6.00
6.20
0.236
0.244
E
6.40
6.60
0.251
0.259
G
4.40
4.60
0.173
0.181
H
9.35
10.10
0.368
0.397
L2
V2
Millimeters
0.80 typ.
0.031 typ.
L4
0.60
1.00
0.023
0.039
V2
0°
8°
0°
8°
Figure 14: DPAK Foot Print Dimensions
(in millimeters)
6.7
3
3
1.6
2.3
6.7
2.3
1.6
7/10
T4 Series
Figure 15: ISOWATT220AB Package Mechanical Data
DIMENSIONS
REF.
Millimeters
Inches
Min.
Max.
Min.
Max.
A
4.40
4.60
0.173
0.181
B
2.50
2.70
0.098
0.106
D
2.50
2.75
0.098
0.108
E
0.40
0.70
0.016
0.028
F
0.75
1.00
0.030
0.039
F1
1.15
1.70
0.045
0.067
F2
1.15
1.70
0.045
0.067
G
4.95
5.20
0.195
0.205
G1
2.40
2.70
0.094
0.106
H
10.00
10.40
0.394
0.409
L2
16.00 typ.
0.630 typ.
L3
28.60
30.60
1.125
1.205
L4
9.80
10.60
0.386
0.417
L6
15.90
16.40
0.626
0.646
L7
9.00
9.30
0.354
0.366
Diam
3.00
3.20
0.118
0.126
Figure 16: IPAK Package Mechanical Data
REF.
A
E
C2
B2
L2
D
H
L
B3
L1
B
A1
V1
B5
e
G
8/10
C
A3
A
A1
A3
B
B2
B3
B5
C
C2
D
E
e
G
H
L
L1
L2
V1
DIMENSIONS
Millimeters
Inches
Min. Typ. Max. Min. Typ.
2.20
2.40 0.086
0.90
1.10 0.035
0.70
1.30 0.027
0.64
0.90 0.025
5.20
5.40 0.204
0.95
0.30
0.035
0.45
0.60 0.017
0.48
0.60 0.019
6
6.20 0.236
6.40
6.60 0.252
2.28
0.090
4.40
4.60 0.173
16.10
0.634
9
9.40 0.354
0.8
1.20 0.031
0.80
1
0.031
10°
10°
Max.
0.094
0.043
0.051
0.035
0.212
0.037
0.023
0.023
0.244
0.260
0.181
0.370
0.047
0.039
T4 Series
Figure 17: TO-220AB Package Mechanical Data
REF.
C
B
ØI
b2
L
F
A
I4
l3
c2
a1
l2
a2
M
c1
b1
e
A
a1
a2
B
b1
b2
C
c1
c2
e
F
ØI
I4
L
l2
l3
M
DIMENSIONS
Millimeters
Inches
Min. Typ. Max. Min. Typ.
15.20
15.90 0.598
3.75
0.147
13.00
14.00 0.511
10.00
10.40 0.393
0.61
0.88 0.024
1.23
1.32 0.048
4.40
4.60 0.173
0.49
0.70 0.019
2.40
2.72 0.094
2.40
2.70 0.094
6.20
6.60 0.244
3.75
3.85 0.147
15.80 16.40 16.80 0.622 0.646
2.65
2.95 0.104
1.14
1.70 0.044
1.14
1.70 0.044
2.60
0.102
Max.
0.625
0.551
0.409
0.034
0.051
0.181
0.027
0.107
0.106
0.259
0.151
0.661
0.116
0.066
0.066
Table 8: Ordering Information
Ordering type
Marking
Package
Weight
Base qty
Delivery mode
T4xx-yyyB
T4 xxyy
DPAK
0.3 g
75
Tube
T4xx-yyyB-TR
T4 xxyy
DPAK
0.3 g
2500
Tape & reel
T4xx-yyyH
T4 xxyy
IPAK
0.4 g
75
Tube
T4xx-yyyT
T4xx yyyT
TO-220AB
2.3 g
50
Tube
T4xx-yyyB
T4xxyyyW
ISOWATT220AB
2.1 g
50
Tube
Note: xxx = voltage, yy = sensitivity
Table 9: Revision History
Date
Revision
Description of Changes
Jun-2003
5
Last update.
25-Mar-2005
6
Layout update. No content change.
25-Jan-2005
7
Markings changed in Table 8
9/10
T4 Series
Information furnished is believed to be accurate and reliable. However, STMicroelectronics assumes no responsibility for the consequences
of use of such information nor for any infringement of patents or other rights of third parties which may result from its use. No license is granted
by implication or otherwise under any patent or patent rights of STMicroelectronics. Specifications mentioned in this publication are subject
to change without notice. This publication supersedes and replaces all information previously supplied. STMicroelectronics products are not
authorized for use as critical components in life support devices or systems without express written approval of STMicroelectronics.
The ST logo is a registered trademark of STMicroelectronics.
All other names are the property of their respective owners
© 2005 STMicroelectronics - All rights reserved
STMicroelectronics group of companies
Australia - Belgium - Brazil - Canada - China - Czech Republic - Finland - France - Germany - Hong Kong - India - Israel - Italy - Japan Malaysia - Malta - Morocco - Singapore - Spain - Sweden - Switzerland - United Kingdom - United States of America
www.st.com
10/10