STMICROELECTRONICS LIS3DH

LIS3DH
MEMS digital output motion sensor
ultra low-power high performance 3-axes “nano” accelerometer
Features
■
Wide supply voltage, 1.71 V to 3.6 V
■
Independent IOs supply (1.8 V) and supply
voltage compatible
■
Ultra low-power mode consumption
down to 2 µA
LGA-16 (3x3x1 mm)
■
±2g/±4g/±8g/±16g dynamically selectable fullscale
■
I2C/SPI digital output interface
■
16 bit data output
■
2 independent programmable interrupt
generators for free-fall and motion detection
belonging to the “nano” family, with digital I2C/SPI
serial interface standard output. The device
features ultra low-power operational modes that
allow advanced power saving and smart
embedded functions.
■
Motion activated functions
■
Free-fall detection
■
Click/double click recognition
The LIS3DH has dynamically user selectable full
scales of ±2g/±4g/±8g/±16g and it is capable of
measuring accelerations with output data rates
from 1 Hz to 5 kHz. The self-test capability allows
the user to check the functioning of the sensor in
the final application. The device may be
configured to generate interrupt signals by two
independent inertial wake-up/free-fall events as
well as by the position of the device itself.
Thresholds and timing of interrupt generators are
programmable by the end user on the fly. The
LIS3DH has an integrated 32-level first in, first out
(FIFO) buffer allowing the user to store data for
host processor intervention reduction. The
LIS3DH is available in small thin plastic land grid
array package (LGA) and it is guaranteed to
operate over an extended temperature range from
-40 °C to +85 °C.
■
Intelligent power saving for handheld devices
Table 1.
■
Pedometer
■
Display orientation
■
Gaming and virtual reality input devices
■
Impact recognition and logging
■
Vibration monitoring and compensation
■
6D/4D orientation detection
■
Free-fall detection
■
Motion detection
■
Embedded temperature sensor
■
Embedded self-test
■
Embedded 96 levels of 16 bit data output FIFO
■
10000 g high shock survivability
■
ECOPACK® RoHS and “Green” compliant
Applications
Device summary
Order codes
Temp.
range [°C]
Package
Packaging
LIS3DH
-40 to +85
LGA-16
Tray
LIS3DHTR
-40 to +85
LGA-16
Tape and reel
Description
The LIS3DH is an ultra low-power high
performance three axes linear accelerometer
May 2010
Doc ID 17530 Rev 1
1/42
www.st.com
42
Contents
LIS3DH
Contents
1
2
Block diagram and pin description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
1.1
Block diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
1.2
Pin description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
Mechanical and electrical specifications . . . . . . . . . . . . . . . . . . . . . . . 10
2.1
Mechanical characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
2.2
Temperature sensor characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
2.3
Electrical characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
2.4
Communication interface characteristics . . . . . . . . . . . . . . . . . . . . . . . . . 12
2.5
3
3.2
2.4.2
I2C - Inter IC control interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
Absolute maximum ratings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
Terminology . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
3.1.1
Sensitivity . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
3.1.2
Zero-g level . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
Functionality . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
3.2.1
Normal mode, low power mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
3.2.2
Self-test . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
3.2.3
6D / 4D orientation detection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
3.3
Sensing element . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
3.4
IC interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
3.5
Factory calibration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
3.6
FIFO . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
3.7
Auxiliary ADC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
Application hints . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
4.1
5
SPI - serial peripheral interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
Terminology and functionality . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
3.1
4
2.4.1
Soldering information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
Digital main blocks . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
5.1
FIFO . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
5.1.1
2/42
Bypass mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
Doc ID 17530 Rev 1
LIS3DH
6
Contents
5.1.2
FIFO mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
5.1.3
Stream mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
5.1.4
Stream-to-FIFO mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
5.1.5
Retrieve data from FIFO . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
Digital interfaces . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
6.1
I2C serial interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
6.1.1
6.2
I2C operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
SPI bus interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
6.2.1
SPI read . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
6.2.2
SPI write . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
6.2.3
SPI read in 3-wires mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25
7
Register mapping . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26
8
Registers description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28
8.1
STATUS_AUX (07h) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28
8.2
OUT_1_L (08h), OUT_1_H (09h) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28
8.3
OUT_2_L (0Ah), OUT_2_H (0Bh) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28
8.4
OUT_3_L (0Ch), OUT_3_H (0Dh) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28
8.5
INT_COUNTER (0Eh) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29
8.6
WHO_AM_I (0Fh) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29
8.7
TEMP_CFG_REG (1Fh) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29
8.8
CTRL_REG1 (20h) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29
8.9
CTRL_REG2 (21h) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30
8.10
CTRL_REG3 (22h) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31
8.11
CTRL_REG4 (23h) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31
8.12
CTRL_REG5 (24h) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32
8.13
CTRL_REG6 (25h) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32
8.14
REFERENCE/DATACAPTURE (26h) . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32
8.15
STATUS_REG (27h) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33
8.16
OUT_X_L (28h), OUT_X_H (29h) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33
8.17
OUT_Y_L (2Ah), OUT_Y_H (2Bh) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33
8.18
OUT_Z_L (2Ch), OUT_Z_H (2Dh) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33
8.19
FIFO_CTRL_REG (2Eh) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34
Doc ID 17530 Rev 1
3/42
Contents
LIS3DH
8.20
FIFO_SRC_REG (2Fh) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34
8.21
INT1_CFG (30h) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34
8.22
INT1_SRC (31h) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35
8.23
INT1_THS (32h) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36
8.24
INT1_DURATION (33h) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36
8.25
CLICK_CFG (38h) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36
8.26
CLICK_SRC (39h) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37
8.27
CLICK_THS (3Ah) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38
8.28
TIME_LIMIT (3Bh) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38
8.29
TIME_LATENCY (3Ch) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38
8.30
TIME WINDOW(3Dh) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38
9
Package information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39
10
Revision history . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41
4/42
Doc ID 17530 Rev 1
LIS3DH
List of figures
List of figures
Figure 1.
Figure 2.
Figure 3.
Figure 4.
Figure 5.
Figure 6.
Figure 7.
Figure 8.
Figure 9.
Figure 10.
Figure 11.
Figure 12.
Block diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
Pin connection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
SPI slave timing diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
I2C Slave timing diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
LIS3DH electrical connection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
Read and write protocol . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
SPI read protocol . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
Multiple bytes SPI read protocol (2 bytes example) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
SPI write protocol . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
Multiple bytes SPI write protocol (2 bytes example) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
SPI read protocol in 3-wires mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25
LGA-16: Mechanical data and package dimensions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40
Doc ID 17530 Rev 1
5/42
List of tables
LIS3DH
List of tables
Table 1.
Table 2.
Table 3.
Table 4.
Table 5.
Table 6.
Table 7.
Table 8.
Table 9.
Table 10.
Table 11.
Table 12.
Table 13.
Table 14.
Table 15.
Table 16.
Table 17.
Table 18.
Table 19.
Table 20.
Table 21.
Table 22.
Table 23.
Table 24.
Table 25.
Table 26.
Table 27.
Table 28.
Table 29.
Table 30.
Table 31.
Table 32.
Table 33.
Table 34.
Table 35.
Table 36.
Table 37.
Table 38.
Table 39.
Table 40.
Table 41.
Table 42.
Table 43.
Table 44.
Table 45.
Table 46.
Table 47.
Table 48.
6/42
Device summary . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
Pin description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Mechanical characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
Temperature sensor characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
Electrical characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
SPI slave timing values. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
I2C slave timing values . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
Absolute maximum ratings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
Operating mode selection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
Serial interface pin description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
Serial interface pin description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
SAD+Read/Write patterns . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
Transfer when master is writing one byte to slave . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
Transfer when master is writing multiple bytes to slave:. . . . . . . . . . . . . . . . . . . . . . . . . . . 21
Transfer when master is receiving (reading) one byte of data from slave: . . . . . . . . . . . . . 22
Transfer when master is receiving (reading) multiple bytes of data from slave . . . . . . . . . 22
Register address map. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26
STATUS_REG_AUX register . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28
STATUS_REG_AUX description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28
INT_COUNTER register . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29
WHO_AM_I register . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29
TEMP_CFG_REG register . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29
TEMP_CFG_REG description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29
CTRL_REG1 register . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29
CTRL_REG1 description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29
Data rate configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30
CTRL_REG2 register . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30
CTRL_REG2 description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30
High pass filter mode configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31
CTRL_REG3 register . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31
CTRL_REG3 description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31
CTRL_REG4 register . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31
CTRL_REG4 description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31
Self test mode configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32
CTRL_REG5 register . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32
CTRL_REG5 description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32
CTRL_REG6 register . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32
REFERENCE register. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32
REFERENCE register description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33
STATUS register. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33
STATUS register description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33
REFERENCE register. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34
REFERENCE register description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34
FIFO mode configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34
FIFO_SRC register . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34
INT1_CFG register . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34
INT1_CFG description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34
Interrupt mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35
Doc ID 17530 Rev 1
LIS3DH
Table 49.
Table 50.
Table 51.
Table 52.
Table 53.
Table 54.
Table 55.
Table 56.
Table 57.
Table 58.
Table 59.
Table 60.
Table 61.
Table 62.
Table 63.
Table 64.
Table 65.
Table 66.
Table 67.
Table 68.
List of tables
INT1_SRC register . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35
INT1_SRC description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35
INT1_THS register . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36
INT1_THS description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36
INT1_DURATION register . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36
INT1_DURATION description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36
CLICK_CFG register. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36
CLICK_CFG description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37
CLICK_SRC register. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37
CLICK_SRC description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37
CLICK_THS register . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38
CLICK_SRC description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38
TIME_LIMIT register . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38
TIME_LIMIT description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38
TIME_LATENCY register . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38
TIME_LATENCY description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38
TIME_WINDOW register . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38
TIME_WINDOW description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38
LGA-16: Mechanical data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40
Document revision history . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41
Doc ID 17530 Rev 1
7/42
Block diagram and pin description
LIS3DH
1
Block diagram and pin description
1.1
Block diagram
Figure 1.
Block diagram
X+
Y+
CHARGE
AMPLIFIER
Z+
a
A/D
CONVERTER 1
MUX
CS
ZY-
CONTROL
LOGIC
X-
SCL/SPC
I2C
SDA/SDO/SDI
SPI
SDO/SA0
ADC1 - ADC Input1
ADC2 - ADC Input2
A/D
CONVERTER 2
ADC3 - ADC Input3
TEMPERATURE
SENSOR
SELF TEST
1.2
TRIMMING
CIRCUITS
REFERENCE
CONTROL LOGIC
&
INTERRUPT GEN.
96 Level
FIFO
CLOCK
Pin description
Figure 2.
Pin connection
X
1
ADC3
ADC1
ADC2
Vdd
Z
13
Pin 1 indicator
1
NC
INT1
NC
SCL/SPC
RES
INT2
9
5
8/42
Doc ID 17530 Rev 1
SDA/SDI/SDO
CS
DIRECTION OF THE
DETECTABLE
ACCELERATIONS
SDO/SA0
Y
(TOP VIEW)
Vdd_IO
GND
(BOTTOM VIEW)
GND
INT 1
INT 2
LIS3DH
Block diagram and pin description
Table 2.
Pin description
Pin#
Name
Function
1
Vdd_IO
2
NC
Not connected
3
NC
Not connected
4
SCL
SPC
I2C serial clock (SCL)
SPI serial port clock (SPC)
5
GND
0V supply
6
SDA
SDI
SDO
I2C serial data (SDA)
SPI serial data input (SDI)
3-wire interface serial data output (SDO)
7
SDO
SA0
SPI serial data output (SDO)
I2C less significant bit of the device address (SA0)
8
CS
9
INT2
Inertial interrupt 2
10
RES
Connect to GND
11
INT1
Inertial interrupt 1
12
GND
0 V supply
13
ADC3
Analog to digital converter input 3
14
Vdd
15
ADC2
Analog to digital converter input 2
16
ADC1
Analog to digital converter input 1
Power supply for I/O pins
SPI enable
I2C/SPI mode selection (1: I2C mode; 0: SPI enabled)
Power supply
Doc ID 17530 Rev 1
9/42
Mechanical and electrical specifications
LIS3DH
2
Mechanical and electrical specifications
2.1
Mechanical characteristics
Vdd = 2.5 V, T = 25 °C unless otherwise noted (a)
Table 3.
Symbol
FS
So
Mechanical characteristics
Parameter
Measurement range(2)
Sensitivity
Test conditions
Min.
Typ.(1)
Max.
Unit
FS bit set to 00
±2.0
FS bit set to 01
±4.0
FS bit set to 10
±8.0
FS bit set to 11
±16.0
g
FS bit set to 00
1
mg/digit
FS bit set to 01
2
mg/digit
FS bit set to 10
4
mg/digit
FS bit set to 11
12
mg/digit
TCSo
Sensitivity change vs
temperature
FS bit set to 00
0.01
%/°C
TyOff
Typical zero-g level
offset accuracy(3),(4)
FS bit set to 00
±40
mg
TCOff
Zero-g level change
vs temperature
Max delta from 25 °C
±0.5
mg/°C
Acceleration noise
density
FS bit set to 00, Normal Mode
(Table 9), ODR = 100Hz
220
ug/sqrt(H
z)
FS bit set to 00
X axis
276
LSb
FS bit set to 00
Self-test
output change(5),(6),(7) Y axis
276
LSb
FS bit set to 00
Z axis
984
LSb
An
Vst
Top
Operating
temperature range
-40
+85
1. Typical specifications are not guaranteed.
2. Verified by wafer level test and measurement of initial offset and sensitivity.
3. Typical zero-g level offset value after MSL3 preconditioning.
4. Offset can be eliminated by enabling the built-in high pass filter.
5. The sign of “Self-test output change” is defined by CTRL_REG4 STsign bit, for all axes.
6. Self-test output changes with the power supply. “Self-test output change” is defined as
OUTPUT[LSb](CTRL_REG4 ST bit=1) - OUTPUT[LSb](CTRL_REG4 ST bit=0). 1LSb=1mg, ±2 g Full-scale.
7. Output data reach 99% of final value after 1 ms when enabling self-test mode, due to device filtering.
a. The product is factory calibrated at 2.5 V. The operational power supply range is from 1.71V to 3.6 V.
10/42
Doc ID 17530 Rev 1
°C
LIS3DH
2.2
Mechanical and electrical specifications
Temperature sensor characteristics
Vdd =2.5 V, T=25 °C unless otherwise noted (b)
Table 4.
Temperature sensor characteristics
Symbol
Parameter
Test condition
TSDr
Temperature sensor output change vs
temperature
TODR
Temperature refresh rate
Top
Operating temperature range
Min.
Typ.(1)
Max.
Unit
1
digit/°C(2)
ODR
Hz
-40
+85
°C
1. Typical specifications are not guaranteed.
2. 8-bit resolution.
2.3
Electrical characteristics
Vdd = 2.5 V, T = 25 °C unless otherwise noted (c)
Table 5.
Electrical characteristics
Min.
Typ.(1)
Max.
Unit
Supply voltage
1.71
2.5
3.6
V
Vdd_IO I/O pins supply voltage(2)
1.71
Vdd+0.1
V
Symbol
Vdd
Parameter
Test conditions
Idd
Current consumption in normal mode
50 Hz ODR
11
µA
Idd
Current consumption in normal mode
1 Hz ODR
2
µA
IddLP
Current consumption in low-power mode
50 Hz ODR
6
µA
IddPdn
Current consumption in power-down
mode
0.5
µA
VIH
Digital high level input voltage
VIL
Digital low level input voltage
VOH
High level output voltage
VOL
Low level output voltage
BW
System bandwidth(3)
Ton
Turn-on time(4)
Top
Operating temperature range
0.8*Vdd_IO
V
0.2*Vdd_IO
0.9*Vdd_IO
V
0.1*Vdd_IO
ODR = 100 Hz
-40
V
V
ODR/2
Hz
1
ms
+85
°C
1. Typical specification are not guaranteed.
2. It is possible to remove Vdd maintaining Vdd_IO without blocking the communication busses, in this condition the
measurement chain is powered off.
3. Referred to Table 25 for the ODR value and configuration.
4. Time to obtain valid data after exiting power-down mode.
b. The product is factory calibrated at 2.5 V.
c.
The product is factory calibrated at 2.5 V. The operational power supply range is from 1.71 V to 3.6 V.
Doc ID 17530 Rev 1
11/42
Mechanical and electrical specifications
LIS3DH
2.4
Communication interface characteristics
2.4.1
SPI - serial peripheral interface
Subject to general operating conditions for Vdd and Top.
Table 6.
SPI slave timing values
Value (1)
Symbol
Parameter
Unit
Min
tc(SPC)
SPI clock cycle
fc(SPC)
SPI clock frequency
tsu(CS)
CS setup time
6
th(CS)
CS hold time
8
tsu(SI)
SDI input setup time
5
th(SI)
SDI input hold time
15
tv(SO)
SDO valid output time
th(SO)
SDO output hold time
tdis(SO)
Figure 3.
CS
100
Note:
12/42
ns
9
50
SPI slave timing diagram
(3)
(3)
tc(SPC)
th(CS)
(3)
(3)
(3)
th(SI)
LSB IN
MSB IN
tv(SO)
SDO
MHz
50
SDO output disable time
tsu(SI)
SDI
ns
10
tsu(CS)
SPC
Max
(3)
tdis(SO)
th(SO)
MSB OUT
(3)
LSB OUT
(3)
1
Values are guaranteed at 10 MHz clock frequency for SPI with both 4 and 3 wires, based on
characterization results, not tested in production.
2
Measurement points are done at 0.2·Vdd_IO and 0.8·Vdd_IO, for both Input and output port.
3
When no communication is on-going, data on CS, SPC, SDI and SDO are driven by internal
pull-up resistors.
Doc ID 17530 Rev 1
LIS3DH
2.4.2
Mechanical and electrical specifications
I2C - Inter IC control interface
Subject to general operating conditions for Vdd and top.
Table 7.
I2C slave timing values
I2C standard mode (1)
Symbol
I2C fast mode (1)
Parameter
f(SCL)
Unit
SCL clock frequency
Min
Max
Min
Max
0
100
0
400
tw(SCLL)
SCL clock low time
4.7
1.3
tw(SCLH)
SCL clock high time
4.0
0.6
tsu(SDA)
SDA setup time
250
100
th(SDA)
SDA data hold time
0.01
kHz
µs
ns
3.45
0.01
0.9
tr(SDA) tr(SCL)
SDA and SCL rise time
1000
20 + 0.1Cb (2)
300
tf(SDA) tf(SCL)
SDA and SCL fall time
300
20 + 0.1Cb (2)
300
th(ST)
START condition hold time
4
0.6
tsu(SR)
Repeated START condition
setup time
4.7
0.6
tsu(SP)
STOP condition setup time
4
0.6
4.7
1.3
µs
ns
µs
tw(SP:SR)
Bus free time between STOP
and START condition
1. Data based on standard I2C protocol requirement, not tested in production.
2. Cb = total capacitance of one bus line, in pF.
Figure 4.
I2C Slave timing diagram
REPEATED
START
START
tsu(SR)
tw(SP:SR)
SDA
tf(SDA)
tsu(SDA)
tr(SDA)
START
th(SDA)
tsu(SP)
STOP
SCL
th(ST)
Note:
tw(SCLL)
tw(SCLH)
tr(SCL)
tf(SCL)
Measurement points are done at 0.2·Vdd_IO and 0.8·Vdd_IO, for both port.
Doc ID 17530 Rev 1
13/42
Mechanical and electrical specifications
2.5
LIS3DH
Absolute maximum ratings
Stresses above those listed as “absolute maximum ratings” may cause permanent damage
to the device. This is a stress rating only and functional operation of the device under these
conditions is not implied. Exposure to maximum rating conditions for extended periods may
affect device reliability.
Table 8.
Absolute maximum ratings
Symbol
Vdd
Vdd_IO
Vin
Note:
Ratings
Maximum value
Unit
Supply voltage
-0.3 to 4.8
V
I/O pins Supply voltage
-0.3 to 4.8
V
-0.3 to Vdd_IO +0.3
V
3000 for 0.5 ms
g
10000 for 0.1 ms
g
3000 for 0.5 ms
g
10000 for 0.1 ms
g
Input voltage on any control pin
(CS, SCL/SPC, SDA/SDI/SDO, SDO/SA0)
APOW
Acceleration (any axis, powered, Vdd = 2.5 V)
AUNP
Acceleration (any axis, unpowered)
TOP
Operating temperature range
-40 to +85
°C
TSTG
Storage temperature range
-40 to +125
°C
ESD
Electrostatic discharge protection
2 (HBM)
kV
Supply voltage on any pin should never exceed 4.8 V
This is a mechanical shock sensitive device, improper handling can cause permanent
damages to the part.
This is an ESD sensitive device, improper handling can cause permanent damages to
the part.
14/42
Doc ID 17530 Rev 1
LIS3DH
Terminology and functionality
3
Terminology and functionality
3.1
Terminology
3.1.1
Sensitivity
Sensitivity describes the gain of the sensor and can be determined e.g. by applying 1 g
acceleration to it. As the sensor can measure DC accelerations this can be done easily by
pointing the axis of interest towards the center of the earth, noting the output value, rotating
the sensor by 180 degrees (pointing to the sky) and noting the output value again. By doing
so, ±1 g acceleration is applied to the sensor. Subtracting the larger output value from the
smaller one, and dividing the result by 2, leads to the actual sensitivity of the sensor. This
value changes very little over temperature and also time. The sensitivity tolerance describes
the range of Sensitivities of a large population of sensors.
3.1.2
Zero-g level
Zero-g level offset (TyOff) describes the deviation of an actual output signal from the ideal
output signal if no acceleration is present. A sensor in a steady state on a horizontal surface
measure 0 g in X axis and 0 g in Y axis whereas the Z axis measure 1 g. The output is
ideally in the middle of the dynamic range of the sensor (content of OUT registers 00h, data
expressed as 2’s complement number). A deviation from ideal value in this case is called
Zero-g offset. Offset is to some extent a result of stress to MEMS sensor and therefore the
offset can slightly change after mounting the sensor onto a printed circuit board or exposing
it to extensive mechanical stress. Offset changes little over temperature, see “Zero-g level
change vs. temperature”. The Zero-g level tolerance (TyOff) describes the standard
deviation of the range of Zero-g levels of a population of sensors.
3.2
Functionality
3.2.1
Normal mode, low power mode
LIS3DH provides two different operating modes respectively reported as normal mode and
low power mode. While normal mode guarantees high resolution, low power mode reduces
further the current consumption.
The table below reported summarizes how to select the operating mode.
Table 9.
Operating mode selection
CTRL_REG1[3]
CTRL_REG4[3]
(LPen bit)
(HR bit)
1
0
Low power mode
0
1
Normal mode
Operating mode
Doc ID 17530 Rev 1
15/42
Terminology and functionality
3.2.2
LIS3DH
Self-test
Self-test allows to check the sensor functionality without moving it. The self-test function is
off when the self-test bit (ST) is programmed to ‘0‘. When the self-test bit is programmed to
‘1‘ an actuation force is applied to the sensor, simulating a definite input acceleration. In this
case the sensor outputs exhibit a change in their DC levels which are related to the selected
full scale through the device sensitivity. When self-test is activated, the device output level is
given by the algebraic sum of the signals produced by the acceleration acting on the sensor
and by the electrostatic test-force. If the output signals change within the amplitude
specified inside Table 3, then the sensor is working properly and the parameters of the
interface chip are within the defined specifications.
3.2.3
6D / 4D orientation detection
The LIS3DH include 6D / 4D orientation detection.
6D / 4D orientation recognition: In this configuration the interrupt is generated when the
device is stable in a known direction. In 4D configuration Z axis position detection is disable.
3.3
Sensing element
A proprietary process is used to create a surface micro-machined accelerometer. The
technology allows carrying out suspended silicon structures which are attached to the
substrate in a few points called anchors and are free to move in the direction of the sensed
acceleration. To be compatible with the traditional packaging techniques a cap is placed on
top of the sensing element to avoid blocking the moving parts during the moulding phase of
the plastic encapsulation.
When an acceleration is applied to the sensor the proof mass displaces from its nominal
position, causing an imbalance in the capacitive half-bridge. This imbalance is measured
using charge integration in response to a voltage pulse applied to the capacitor.
At steady state the nominal value of the capacitors are few pF and when an acceleration is
applied the maximum variation of the capacitive load is in the fF range.
3.4
IC interface
The complete measurement chain is composed by a low-noise capacitive amplifier which
converts the capacitive unbalancing of the MEMS sensor into an analog voltage that is
finally available to the user by an analog-to-digital converter.
The acceleration data may be accessed through an I2C/SPI interface thus making the
device particularly suitable for direct interfacing with a microcontroller.
The LIS3DH features a Data-Ready signal (RDY) which indicates when a new set of
measured acceleration data is available thus simplifying data synchronization in the digital
system that uses the device.
The LIS3DH may also be configured to generate an inertial Wake-Up and Free-Fall interrupt
signal accordingly to a programmed acceleration event along the enabled axes. Both FreeFall and Wake-Up can be available simultaneously on two different pins.
16/42
Doc ID 17530 Rev 1
LIS3DH
3.5
Terminology and functionality
Factory calibration
The IC interface is factory calibrated for sensitivity (So) and Zero-g level (TyOff).
The trimming values are stored inside the device in a non volatile memory. Any time the
device is turned on, the trimming parameters are downloaded into the registers to be used
during the active operation. This allows to use the device without further calibration.
3.6
FIFO
The LIS3DH contains a 10 bit, 32-level FIFO. Buffered output allows 4 operation modes:
FIFO, stream, trigger and FIFO ByPass. Where FIFO bypass mode is activated FIFO is not
operating and remains empty. In FIFO mode, data from acceleration detection on x, y, and zaxes measurements are stored in FIFO.
3.7
Auxiliary ADC
The LIS3DH contains an auxiliary 10 bit ADC with 3 separate dedicated inputs.
Doc ID 17530 Rev 1
17/42
Application hints
4
LIS3DH
Application hints
Figure 5.
LIS3DH electrical connection
ADC1 ADC2
Vdd
16
10µF
14
1
Vdd_IO
13
ADC3
TOP VIEW
INT1
100nF
9
5
8
INT2
Vdd_IO
Rpu
CS
Rpu
SDO/SA0
SDA/SDI/SDO
SCL/SPC
6
Pull-up to be added
when I2C interface is used
GND
Digital signal from/to signal controller.Signal’s levels are defined by proper selection of Vdd_IO
The device core is supplied through Vdd line while the I/O pads are supplied through
Vdd_IO line. Power supply decoupling capacitors (100 nF ceramic, 10 µF aluminum) should
be placed as near as possible to the pin 14 of the device (common design practice).
All the voltage and ground supplies must be present at the same time to have proper
behavior of the IC (refer to Figure 5). It is possible to remove Vdd maintaining Vdd_IO
without blocking the communication bus, in this condition the measurement chain is
powered off.
The functionality of the device and the measured acceleration data is selectable and
accessible through the I2C or SPI interfaces.When using the I2C, CS must be tied high.
The ADC1, ADC2 & ADC3 if not used can be left floating or keep connected to Vdd or GND.
The functions, the threshold and the timing of the two interrupt pins (INT1 and INT2) can be
completely programmed by the user through the I2C/SPI interface.
4.1
Soldering information
The LGA package is compliant with the ECOPACK®, RoHS and “Green” standard.
It is qualified for soldering heat resistance according to JEDEC J-STD-020.
Leave “Pin 1 Indicator” unconnected during soldering.
Land pattern and soldering recommendations are available at www.st.com.
18/42
Doc ID 17530 Rev 1
LIS3DH
Digital main blocks
5
Digital main blocks
5.1
FIFO
LIS3DH embeds a 32-slot of 10bit data FIFO for each of the three output channels, X, Y and
Z. This allows a consistent power saving for the system, since the host processor does not
need to continuously poll data from the sensor, but it can wakeup only when needed and
burst the significant data out from the FIFO. This buffer can work accordingly to four different
modes: Bypass mode, FIFO mode, Stream mode and Stream-to-FIFO mode. Each mode is
selected by the FIFO_MODE bits into the FIFO_CTRL_REG (2E). Programmable
Watermark level, FIFO_empty or FIFO_Full events can be enabled to generate dedicated
interrupts on INT1/2 pin (configuration through FIFO_CFG_REG).
5.1.1
Bypass mode
In Bypass mode, the FIFO is not operational and for this reason it remains empty. As
described in the next figure, for each channel only the first address is used. The remaining
FIFO slots are empty.
5.1.2
FIFO mode
In FIFO mode, data from X, Y and Z channels are stored into the FIFO. A watermark
interrupt can be enabled (FIFO_WTMK_EN bit into FIFO_CTRL_REG in order to be raised
when the FIFO is filled to the level specified into the FIFO_WTMK_LEVEL bits of
FIFO_CTRL_REG. The FIFO continues filling until it is full (32 slots of 10data for X, Y and
Z). When full, the FIFO stops collecting data from the input channels.
5.1.3
Stream mode
In the stream mode, data from X, Y and Z measurement are stored into the FIFO. A
watermark interrupt can be enabled and set as in the FIFO mode.The FIFO continues filling
until it’s full (32 slots of 10data for X, Y and Z). When full, the FIFO discards the older data
as the new arrive.
5.1.4
Stream-to-FIFO mode
In Stream-to_FIFO mode, data from X, Y and Z measurement are stored into the FIFO. A
watermark interrupt can be enabled (FIFO_WTMK_EN bit into FIFO_CTRL_REG) in order
to be raised when the FIFO is filled to the level specified into the FIFO_WTMK_LEVEL bits
of FIFO_CTRL_REG. The FIFO continues filling until it’s full (32 slots of 10 data for X, Y and
Z). When full, the FIFO discards the older data as the new arrive. Once trigger event occurs,
the FIFO starts operating in FIFO mode.
5.1.5
Retrieve data from FIFO
FIFO data is read through OUT_X (Addr reg 28h,29h), OUT_Y (Addr reg 2Ah,2Bh) and
OUT_Z (Addr reg 2Ch,2Dh). When the FIFO is in stream, Trigger or FIFO mode, a read
operation to the OUT_X, OUT_Y or OUT_Z registers provides the data stored into the FIFO.
Each time data is read from the FIFO, the oldest X, Y and Z data are placed into the OUT_X,
OUT_Y and OUT_Z registers and both single read and read_burst operations can be used.
Doc ID 17530 Rev 1
19/42
Digital interfaces
6
LIS3DH
Digital interfaces
The registers embedded inside the LIS3DH may be accessed through both the I2C and SPI
serial interfaces. The latter may be SW configured to operate either in 3-wire or 4-wire
interface mode.
The serial interfaces are mapped onto the same pads. To select/exploit the I2C interface, CS
line must be tied high (i.e. connected to Vdd_IO).
Table 10.
Serial interface pin description
Pin name
SPI enable
I2C/SPI mode selection (1: I2C mode; 0: SPI enabled)
CS
6.1
Pin description
SCL
SPC
I2C serial clock (SCL)
SPI serial port clock (SPC)
SDA
SDI
SDO
I2C serial data (SDA)
SPI serial data input (SDI)
3-wire interface serial data output (SDO)
SA0
SDO
I2C less significant bit of the device address (SA0)
SPI serial data output (SDO)
I2C serial interface
The LIS3DH I2C is a bus slave. The I2C is employed to write data into registers whose
content can also be read back.
The relevant I2C terminology is given in the table below.
Table 11.
Serial interface pin description
Term
Transmitter
Receiver
Description
The device which sends data to the bus
The device which receives data from the bus
Master
The device which initiates a transfer, generates clock signals and terminates a
transfer
Slave
The device addressed by the master
There are two signals associated with the I2C bus: the serial clock line (SCL) and the Serial
DAta line (SDA). The latter is a bidirectional line used for sending and receiving the data
to/from the interface. Both the lines must be connected to Vdd_IO through external pull-up
resistor. When the bus is free both the lines are high.
The I2C interface is compliant with fast mode (400 kHz) I2C standards as well as with the
normal mode.
20/42
Doc ID 17530 Rev 1
LIS3DH
6.1.1
Digital interfaces
I2C operation
The transaction on the bus is started through a START (ST) signal. A START condition is
defined as a HIGH to LOW transition on the data line while the SCL line is held HIGH. After
this has been transmitted by the Master, the bus is considered busy. The next byte of data
transmitted after the start condition contains the address of the slave in the first 7 bits and
the eighth bit tells whether the Master is receiving data from the slave or transmitting data to
the slave. When an address is sent, each device in the system compares the first seven bits
after a start condition with its address. If they match, the device considers itself addressed
by the Master.
The Slave ADdress (SAD) associated to the LIS3DH is 001100xb. SDO/SA0 pad can be
used to modify less significant bit of the device address. If SA0 pad is connected to voltage
supply, LSb is ‘1’ (address 0011001b) else if SA0 pad is connected to ground, LSb value is
‘0’ (address 0011000b). This solution permits to connect and address two different
accelerometers to the same I2C lines.
Data transfer with acknowledge is mandatory. The transmitter must release the SDA line
during the acknowledge pulse. The receiver must then pull the data line LOW so that it
remains stable low during the HIGH period of the acknowledge clock pulse. A receiver which
has been addressed is obliged to generate an acknowledge after each byte of data
received.
The I2C embedded inside the LIS3DH behaves like a slave device and the following protocol
must be adhered to. After the start condition (ST) a slave address is sent, once a slave
acknowledge (SAK) has been returned, a 8-bit sub-address (SUB) is transmitted: the 7 LSb
represent the actual register address while the MSB enables address auto increment. If the
MSb of the SUB field is ‘1’, the SUB (register address) is automatically increased to allow
multiple data read/write.
The slave address is completed with a Read/Write bit. If the bit was ‘1’ (Read), a repeated
START (SR) condition must be issued after the two sub-address bytes; if the bit is ‘0’ (Write)
the Master transmit to the slave with direction unchanged. Table 12 explains how the
SAD+Read/Write bit pattern is composed, listing all the possible configurations.
Table 12.
SAD+Read/Write patterns
Command
SAD[6:1]
SAD[0] = SA0
R/W
Read
001100
0
1
00110001 (31h)
Write
001100
0
0
00110000 (30h)
Read
001100
1
1
00110011 (33h)
Write
001100
1
0
00110010 (32h)
Table 13.
Transfer when master is writing one byte to slave
Master
ST
SAD + W
Slave
Table 14.
Master
Slave
SAD+R/W
SUB
SAK
DATA
SAK
SP
SAK
Transfer when master is writing multiple bytes to slave:
ST
SAD + W
SUB
SAK
DATA
SAK
Doc ID 17530 Rev 1
DATA
SAK
SP
SAK
21/42
Digital interfaces
LIS3DH
Table 15.
Master
Transfer when master is receiving (reading) one byte of data from slave:
ST
SAD + W
Slave
Table 16.
SUB
SAK
SR
SAD + R
SAK
NMAK
SAK
SP
DATA
Transfer when master is receiving (reading) multiple bytes of data from slave
Master ST SAD+W
Slave
SUB
SAK
SR SAD+R
SAK
MAK
SAK DATA
MAK
DATA
NMAK SP
DATA
Data are transmitted in byte format (DATA). Each data transfer contains 8 bits. The number
of bytes transferred per transfer is unlimited. Data is transferred with the Most Significant bit
(MSb) first. If a receiver can’t receive another complete byte of data until it has performed
some other function, it can hold the clock line, SCL LOW to force the transmitter into a wait
state. Data transfer only continues when the receiver is ready for another byte and releases
the data line. If a slave receiver doesn’t acknowledge the slave address (i.e. it is not able to
receive because it is performing some real time function) the data line must be left HIGH by
the slave. The Master can then abort the transfer. A LOW to HIGH transition on the SDA line
while the SCL line is HIGH is defined as a STOP condition. Each data transfer must be
terminated by the generation of a STOP (SP) condition.
In order to read multiple bytes, it is necessary to assert the most significant bit of the subaddress field. In other words, SUB(7) must be equal to 1 while SUB(6-0) represents the
address of first register to be read.
In the presented communication format MAK is Master acknowledge and NMAK is No
Master Acknowledge.
6.2
SPI bus interface
The LIS3DH SPI is a bus slave. The SPI allows to write and read the registers of the device.
The Serial Interface interacts with the outside world with 4 wires: CS, SPC, SDI and SDO.
Figure 6.
Read and write protocol
CS
SPC
SDI
DI7 DI6 DI5 DI4 DI3 DI2 DI1 DI0
RW
MS AD5 AD4 AD3 AD2 AD1 AD0
SDO
DO7 DO6 DO5 DO4 DO3 DO2 DO1 DO0
CS is the serial port enable and it is controlled by the SPI master. It goes low at the start of
the transmission and goes back high at the end. SPC is the serial port clock and it is
controlled by the SPI master. It is stopped high when CS is high (no transmission). SDI and
22/42
Doc ID 17530 Rev 1
LIS3DH
Digital interfaces
SDO are respectively the serial port data input and output. Those lines are driven at the
falling edge of SPC and should be captured at the rising edge of SPC.
Both the read register and write register commands are completed in 16 clock pulses or in
multiple of 8 in case of multiple bytes read/write. Bit duration is the time between two falling
edges of SPC. The first bit (bit 0) starts at the first falling edge of SPC after the falling edge
of CS while the last bit (bit 15, bit 23, ...) starts at the last falling edge of SPC just before the
rising edge of CS.
bit 0: RW bit. When 0, the data DI(7:0) is written into the device. When 1, the data DO(7:0)
from the device is read. In latter case, the chip drives SDO at the start of bit 8.
bit 1: MS bit. When 0, the address remains unchanged in multiple read/write commands.
When 1, the address is auto incremented in multiple read/write commands.
bit 2-7: address AD(5:0). This is the address field of the indexed register.
bit 8-15: data DI(7:0) (write mode). This is the data that is written into the device (MSb first).
bit 8-15: data DO(7:0) (read mode). This is the data that is read from the device (MSb first).
In multiple read/write commands further blocks of 8 clock periods is added. When MS bit is
‘0’ the address used to read/write data remains the same for every block. When MS bit is ‘1’
the address used to read/write data is increased at every block.
The function and the behavior of SDI and SDO remain unchanged.
6.2.1
SPI read
Figure 7.
SPI read protocol
CS
SPC
SDI
RW
MS AD5 AD4 AD3 AD2 AD1 AD0
SDO
DO7 DO6 DO5 DO4 DO3 DO2 DO1 DO0
The SPI Read command is performed with 16 clock pulses. Multiple byte read command is
performed adding blocks of 8 clock pulses at the previous one.
bit 0: READ bit. The value is 1.
bit 1: MS bit. When 0 do not increment address, when 1 increment address in multiple
reading.
bit 2-7: address AD(5:0). This is the address field of the indexed register.
bit 8-15: data DO(7:0) (read mode). This is the data that is read from the device (MSb first).
bit 16-... : data DO(...-8). Further data in multiple byte reading.
Doc ID 17530 Rev 1
23/42
Digital interfaces
LIS3DH
Figure 8.
Multiple bytes SPI read protocol (2 bytes example)
CS
SPC
SDI
RW
MS AD5 AD4 AD3 AD2 AD1 AD0
SDO
DO7 DO6 DO5 DO4 DO3 DO2 DO1 DO0 DO15DO14DO13DO12DO11DO10DO9 DO8
6.2.2
SPI write
Figure 9.
SPI write protocol
CS
SPC
SDI
DI7 DI6 DI5 DI4 DI3 DI2 DI1 DI0
RW
MS AD5 AD4 AD3 AD2 AD1 AD0
The SPI Write command is performed with 16 clock pulses. Multiple byte write command is
performed adding blocks of 8 clock pulses at the previous one.
bit 0: WRITE bit. The value is 0.
bit 1: MS bit. When 0 do not increment address, when 1 increment address in multiple
writing.
bit 2 -7: address AD(5:0). This is the address field of the indexed register.
bit 8-15: data DI(7:0) (write mode). This is the data that is written inside the device (MSb
first).
bit 16-... : data DI(...-8). Further data in multiple byte writing.
Figure 10. Multiple bytes SPI write protocol (2 bytes example)
CS
SPC
SDI
DI7 DI6 DI5 DI4 DI3 DI2 DI1 DI0 DI15 DI14 DI13 DI12 DI11 DI10 DI9 DI8
RW
MS AD5 AD4 AD3 AD2 AD1 AD0
24/42
Doc ID 17530 Rev 1
LIS3DH
6.2.3
Digital interfaces
SPI read in 3-wires mode
3-wires mode is entered by setting to ‘1’ bit SIM (SPI serial interface mode selection) in
CTRL_REG4.
Figure 11. SPI read protocol in 3-wires mode
CS
SPC
SDI/O
DO7 DO6 DO5 DO4 DO3 DO2 DO1 DO0
RW
MS AD5 AD4 AD3 AD2 AD1 AD0
The SPI read command is performed with 16 clock pulses:
bit 0: READ bit. The value is 1.
bit 1: MS bit. When 0 do not increment address, when 1 increment address in multiple
reading.
bit 2-7: address AD(5:0). This is the address field of the indexed register.
bit 8-15: data DO(7:0) (read mode). This is the data that is read from the device (MSb first).
Multiple read command is also available in 3-wires mode.
Doc ID 17530 Rev 1
25/42
Register mapping
7
LIS3DH
Register mapping
The table given below provides a listing of the 8 bit registers embedded in the device and
the related addresses:
Table 17.
Register address map
Register address
Name
Type
Default
Hex
Reserved (do not modify)
00 - 06
Reserved
STATUS_REG_AUX
r
07
000 0111
OUT_ADC1_L
r
08
000 1000
output
OUT_ADC1_H
r
09
000 1001
output
OUT_ADC2_L
r
0A
000 1010
output
OUT_ADC2_H
r
0B
000 1011
output
OUT_ADC3_L
r
0C
000 1100
output
OUT_ADC3_H
r
0D
000 1101
output
INT_COUNTER_REG
r
0E
000 1110
WHO_AM_I
r
0F
000 1111 00110011 Dummy register
Reserved (do not modify)
10 - 1E
Reserved
TEMP_CFG_REG
rw
1F
001 1111
CTRL_REG1
rw
20
010 0000 00000111
CTRL_REG2
rw
21
010 0001 00000000
CTRL_REG3
rw
22
010 0010 00000000
CTRL_REG4
rw
23
010 0011 00000000
CTRL_REG5
rw
24
010 0100 00000000
CTRL_REG6
rw
25
010 0101 00000000
REFERENCE
rw
26
010 0110 00000000
STATUS_REG2
r
27
010 0111 00000000
OUT_X_L
r
28
010 1000
output
OUT_X_H
r
29
010 1001
output
OUT_Y_L
r
2A
010 1010
output
OUT_Y_H
r
2B
010 1011
output
OUT_Z_L
r
2C
010 1100
output
OUT_Z_H
r
2D
010 1101
output
FIFO_CTRL_REG
rw
2E
010 1110 00000000
FIFO_SRC_REG
r
2F
010 1111
rw
30
011 0000 00000000
INT1_CFG
26/42
Comment
Binary
Doc ID 17530 Rev 1
LIS3DH
Register mapping
Table 17.
Register address map
Register address
Name
Type
Default
Hex
INT1_SOURCE
Comment
Binary
r
31
011 0001 00000000
INT1_THS
rw
32
011 0010 00000000
INT1_DURATION
rw
33
011 0011 00000000
Reserved
rw
34-37
CLICK_CFG
rw
38
011 1000 00000000
CLICK_SRC
r
39
011 1001 00000000
CLICK_THS
rw
3A
011 1010 00000000
TIME_LIMIT
rw
3B
011 1011 00000000
TIME_LATENCY
rw
3C
011 1100 00000000
TIME_WINDOW
rw
3D
011 1101 00000000
00000000
Registers marked as Reserved must not be changed. The writing to those registers may
cause permanent damages to the device.
The content of the registers that are loaded at boot should not be changed. They contain the
factory calibration values. Their content is automatically restored when the device is
powered-up.
Doc ID 17530 Rev 1
27/42
Registers description
LIS3DH
8
Registers description
8.1
STATUS_AUX (07h)
Table 18.
321OR
Table 19.
321OR
STATUS_REG_AUX register
3OR
2OR
1OR
321DA
3DA
2DA
1DA
STATUS_REG_AUX description
1, 2 and 3 axis data overrun. Default value: 0
(0: no overrun has occurred; 1: a new set of data has overwritten the previous ones)
3OR
3 axis data overrun. Default value: 0
(0: no overrun has occurred;
1: a new data for the 3-axis has overwritten the previous one)
2OR
2 axis data overrun. Default value: 0
(0: no overrun has occurred;
1: a new data for the 4-axis has overwritten the previous one)
1OR
1 axis data overrun. Default value: 0
(0: no overrun has occurred;
1: a new data for the 1-axis has overwritten the previous one)
321DA
3DA
1, 2 and 3 axis new data available. Default value: 0
(0: a new set of data is not yet available; 1: a new set of data is available)
3 axis new data available. Default value: 0
(0: a new data for the 3-axis is not yet available;
1: a new data for the 3-axis is available)
8.2
2DA
2 axis new data available. Default value: 0
(0: a new data for the 2-axis is not yet available;
1: a new data for the 2-axis is available)
1DA
1 axis new data available. Default value: 0
(0: a new data for the 1-axis is not yet available;
1: a new data for the 1-axis is available)
OUT_1_L (08h), OUT_1_H (09h)
1-axis acceleration data. The value is expressed in two’s complement.
8.3
OUT_2_L (0Ah), OUT_2_H (0Bh)
2-axis acceleration data. The value is expressed in two’s complement.
8.4
OUT_3_L (0Ch), OUT_3_H (0Dh)
3-axis acceleration data. The value is expressed in two’s complement.
28/42
Doc ID 17530 Rev 1
LIS3DH
8.5
Registers description
INT_COUNTER (0Eh)
Table 20.
IC7
8.6
INT_COUNTER register
IC6
IC5
IC4
IC3
IC2
IC1
IC0
WHO_AM_I (0Fh)
Table 21.
0
WHO_AM_I register
0
1
1
0
0
1
1
0
0
0
0
Zen
Yen
Xen
Device identification register.
8.7
TEMP_CFG_REG (1Fh)
Table 22.
ADC_PD
Table 23.
ADC_PD
TEMP_EN
8.8
TEMP_CFG_REG register
TEMP_EN
0
0
TEMP_CFG_REG description
ADC enable. Default value: 0
(0: ADC disabled; 1: ADC enabled)
Temperature sensor (T) enable. Default value: 0
(0: T disabled; 1: T enabled)
CTRL_REG1 (20h)
Table 24.
ODR3
Table 25.
ODR3-0
CTRL_REG1 register
ODR2
ODR1
ODR0
LPen
CTRL_REG1 description
Data rate selection. Default value: 00
(0000:50 Hz; Others: Refer to Table 25, “Data rate configuration”)
LPen
Low power mode enable. Default value: 0
(0: normal mode, 1: low power mode)
Zen
Z axis enable. Default value: 1
(0: Z axis disabled; 1: Z axis enabled)
Yen
Y axis enable. Default value: 1
(0: Y axis disabled; 1: Y axis enabled)
Xen
X axis enable. Default value: 1
(0: X axis disabled; 1: X axis enabled)
Doc ID 17530 Rev 1
29/42
Registers description
LIS3DH
ODR<3:0> is used to set power mode and ODR selection. In the following table are reported
all frequency resulting in combination of ODR<3:0>
Table 26.
Data rate configuration
ODR3
8.9
ODR2
ODR0
Power mode selection
0
0
0
0
Power down mode
0
0
0
1
Normal / low power mode (1 Hz)
0
0
1
0
Normal / low power mode (10 Hz)
0
0
1
1
Normal / low power mode (25 Hz)
0
1
0
0
Normal / low power mode (50 Hz)
0
1
0
1
Normal / low power mode (100 Hz)
0
1
1
0
Normal / low power mode (200 Hz)
0
1
1
1
Normal / low power mode (400 Hz)
1
0
0
0
Low power mode (1.6 KHz)
1
0
0
1
Normal (1.25 kHz) / low power mode (5 KHz)
CTRL_REG2 (21h)
Table 27.
CTRL_REG2 register
HPM1
Table 28.
HPM0
HPCF2
HPCF1
FDS
HPCLICK
HPIS2
HPIS1
CTRL_REG2 description
HPM1 -HPM0
30/42
ODR1
High pass filter mode selection. Default value: 00
Refer to Table 29, "High pass filter mode configuration"
HPCF2 HPCF1
High pass filter cut off frequency selection
FDS
Filtered data selection. Default value: 0
(0: internal filter bypassed; 1: data from internal filter sent to output register and
FIFO)
HPCLICK
High pass filter enabled for CLICK function.
(0: filter bypassed; 1: filter enabled)
HPIS2
High pass filter enabled for AOI function on interrupt 2,
(0: filter bypassed; 1: filter enabled)
HPIS1
High pass filter enabled for AOI function on interrupt 1,
(0: filter bypassed; 1: filter enabled)
Doc ID 17530 Rev 1
LIS3DH
Registers description
Table 29.
High pass filter mode configuration
HPM1
8.10
High pass filter mode
0
0
Normal mode (reset reading HP_RESET_FILTER)
0
1
Reference signal for filtering
1
0
Normal mode
1
1
Autoreset on interrupt event
CTRL_REG3 (22h)
Table 30.
I1_CLICK
Table 31.
8.11
HPM0
CTRL_REG3 register
I1_AOI1
I1_AOI2
I1_DRDY1
I1_DRDY2
I1_WTM
I1_OVERRUN
--
CTRL_REG3 description
I1_CLICK
CLICK interrupt on INT1. Default value 0.
(0: Disable; 1: Enable)
I1_AOI1
AOI1 interrupt on INT1. Default value 0.
(0: Disable; 1: Enable)
I1_AOI2
AOI2 interrupt on INT1. Default value 0.
(0: Disable; 1: Enable)
I1_DRDY1
DRDY1 interrupt on INT1. Default value 0.
(0: Disable; 1: Enable)
I1_DRDY2
DRDY2 interrupt on INT1. Default value 0.
(0: Disable; 1: Enable)
I1_WTM
FIFO Watermark interrupt on INT1. Default value 0.
(0: Disable; 1: Enable)
I1_OVERRUN
FIFO Overrun interrupt on INT1. Default value 0.
(0: Disable; 1: Enable)
CTRL_REG4 (23h)
Table 32.
BDU
Table 33.
CTRL_REG4 register
BLE
FS1
FS0
HR
ST1
ST0
SIM
CTRL_REG4 description
BDU
Block data update. Default value: 0
(0: continuos update; 1: output registers not updated until MSB and LSB
reading)
BLE
Big/little endian data selection. Default value 0.
(0: Data LSB @ lower address; 1: Data MSB @ lower address)
FS1-FS0
Full scale selection. default value: 00
(00: +/- 2G; 01: +/- 4G; 10: +/- 8G; 11: +/- 16G)
Doc ID 17530 Rev 1
31/42
Registers description
Table 33.
LIS3DH
CTRL_REG4 description (continued)
HR
High resolution output mode: Default value: 0
(0: High resolution disable; 1: High resolution Enable)
ST1-ST0
Self test enable. Default value: 00
(00: Self test disabled; Other: See Table 34)
SIM
SPI serial interface mode selection. Default value: 0
(0: 4-wire interface; 1: 3-wire interface).
Table 34.
Self test mode configuration
ST1
8.12
0
Normal mode
0
1
Self test 0
1
0
Self test 1
1
1
--
CTRL_REG5 (24h)
BOOT
Table 36.
--
--
LIR_INT1
D4D_INT1
0
0
CTRL_REG5 description
Reboot memory content. Default value: 0
(0: normal mode; 1: reboot memory content)
FIFO_EN
FIFO enable. Default value: 0
(0: FIFO disable; 1: FIFO Enable)
LIR_INT1
Latch interrupt request on INT1_SRC register, with INT1_SRC register
cleared by reading INT1_SRC itself. Default value: 0.
(0: interrupt request not latched; 1: interrupt request latched)
D4D_INT1
4D enable: 4D detection is enabled on INT1 when 6D bit on INT1_CFG is set
to 1.
CTRL_REG6 (25h)
I2_CLICKen
CTRL_REG6 register
I2_INT1
0
BOOT_I1
0
--
H_LACTIVE
-
REFERENCE/DATACAPTURE (26h)
Table 38.
Ref7
32/42
CTRL_REG5 register
FIFO_EN
BOOT
Table 37.
8.14
Self test mode
0
Table 35.
8.13
ST0
REFERENCE register
Ref6
Ref5
Ref4
Ref3
Doc ID 17530 Rev 1
Ref2
Ref1
Ref0
LIS3DH
Registers description
Table 39.
REFERENCE register description
Ref 7-Ref0
8.15
STATUS_REG (27h)
Table 40.
ZYXOR
Table 41.
8.16
Reference value for Interrupt generation. Default value: 0
STATUS register
ZOR
YOR
XOR
ZYXDA
ZDA
YDA
XDA
STATUS register description
ZYXOR
X, Y and Z axis data overrun. Default value: 0
(0: no overrun has occurred; 1: a new set of data has overwritten the previous ones)
ZOR
Z axis data overrun. Default value: 0
(0: no overrun has occurred; 1: a new data for the Z-axis has overwritten the previous
one)
YOR
Y axis data overrun. Default value: 0
(0: no overrun has occurred;
1: a new data for the Y-axis has overwritten the previous one)
XOR
X axis data overrun. Default value: 0
(0: no overrun has occurred;
1: a new data for the X-axis has overwritten the previous one)
ZYXDA
X, Y and Z axis new data available. Default value: 0
(0: a new set of data is not yet available; 1: a new set of data is available)
ZDA
Z axis new data available. Default value: 0
(0: a new data for the Z-axis is not yet available;
1: a new data for the Z-axis is available)
YDA
Y axis new data available. Default value: 0
(0: a new data for the Y-axis is not yet available;
1: a new data for the Y-axis is available)
OUT_X_L (28h), OUT_X_H (29h)
X-axis acceleration data. The value is expressed in two’s complement.
8.17
OUT_Y_L (2Ah), OUT_Y_H (2Bh)
Y-axis acceleration data. The value is expressed in two’s complement.
8.18
OUT_Z_L (2Ch), OUT_Z_H (2Dh)
Z-axis acceleration data. The value is expressed in two’s complement.
Doc ID 17530 Rev 1
33/42
Registers description
8.19
LIS3DH
FIFO_CTRL_REG (2Eh)
Table 42.
REFERENCE register
FM1
FM0
Table 43.
TR
FIFO mode selection. Default value: 00 (see Table 44)
TR
Trigger selection. Default value: 0
0: Trigger event liked to trigger signal on INT1
1: Trigger event liked to trigger signal on INT2
FTH4:0
Default value: 0
FTH1
FTH0
FIFO mode configuration
FM0
Self test mode
0
0
Bypass mode
0
1
FIFO mode
1
0
Stream mode
1
1
Trigger mode
FIFO_SRC_REG (2Fh)
Table 45.
WTM
FIFO_SRC register
OVRN_FIFO
EMPTY
FSS4
FSS3
FSS2
FSS1
FSS0
INT1_CFG (30h)
Table 46.
AOI
6D
Table 47.
34/42
FTH2
FM1-FM0
FM1
8.21
FTH3
REFERENCE register description
Table 44.
8.20
FTH4
INT1_CFG register
ZHIE/
ZUPE
ZLIE/
ZDOWNE
YHIE/
YUPE
YLIE/
YDOWNE
XHIE/
XUPE
XLIE/
XDOWNE
INT1_CFG description
AOI
And/Or combination of Interrupt events. Default value: 0. Refer to Table 48, "Interrupt mode"
6D
6 direction detection function enabled. Default value: 0. Refer to Table 48, "Interrupt
mode"
ZHIE/
ZUPE
Enable interrupt generation on Z high event or on Direction recognition. Default
value: 0 (0: disable interrupt request;1: enable interrupt request)
Doc ID 17530 Rev 1
LIS3DH
Registers description
Table 47.
INT1_CFG description
ZLIE/
ZDOWNE
Enable interrupt generation on Z low event or on Direction recognition. Default
value: 0 (0: disable interrupt request;1: enable interrupt request)
YHIE/
YUPE
Enable interrupt generation on Y high event or on Direction recognition. Default
value: 0 (0: disable interrupt request; 1: enable interrupt request.)
YLIE/
YDOWNE
Enable interrupt generation on Y low event or on Direction recognition. Default
value: 0 (0: disable interrupt request; 1: enable interrupt request.)
XHIE/
XUPE
Enable interrupt generation on X high event or on Direction recognition. Default
value: 0 (0: disable interrupt request; 1: enable interrupt request.)
XLIE/XDOWNE Enable interrupt generation on X low event or on Direction recognition. Default
value: 0 (0: disable interrupt request; 1: enable interrupt request.)
Content of this register is loaded at boot.
Write operation at this address is possible only after system boot.
Table 48.
Interrupt mode
AOI
6D
Interrupt mode
0
0
OR combination of interrupt events
0
1
6 direction movement recognition
1
0
AND combination of interrupt events
1
1
6 direction position recognition
Difference between AOI-6D = ‘01’ and AOI-6D = ‘11’.
AOI-6D = ‘01’ is movement recognition. An interrupt is generate when orientation move from
unknown zone to known zone. The interrupt signal stay for a duration ODR.
AOI-6D = ‘11’ is direction recognition. An interrupt is generate when orientation is inside a
known zone. The interrupt signal stay until orientation is inside the zone.
8.22
INT1_SRC (31h)
Table 49.
0
Table 50.
INT1_SRC register
IA
ZH
ZL
YH
YL
XH
XL
INT1_SRC description
IA
Interrupt active. Default value: 0
(0: no interrupt has been generated; 1: one or more interrupts have been generated)
ZH
Z high. Default value: 0
(0: no interrupt, 1: Z High event has occurred)
ZL
Z low. Default value: 0
(0: no interrupt; 1: Z Low event has occurred)
YH
Y high. Default value: 0
(0: no interrupt, 1: Y High event has occurred)
Doc ID 17530 Rev 1
35/42
Registers description
Table 50.
LIS3DH
INT1_SRC description
YL
Y low. Default value: 0
(0: no interrupt, 1: Y Low event has occurred)
XH
X high. Default value: 0
(0: no interrupt, 1: X High event has occurred)
XL
X low. Default value: 0
(0: no interrupt, 1: X Low event has occurred)
Interrupt 1 source register. Read only register.
Reading at this address clears INT1_SRC IA bit (and the interrupt signal on INT 1 pin) and
allows the refreshment of data in the INT1_SRC register if the latched option was chosen.
8.23
INT1_THS (32h)
Table 51.
INT1_THS register
0
Table 52.
THS6
THS4
THS3
THS2
THS1
THS0
D2
D1
D0
INT1_THS description
THS6 - THS0
8.24
THS5
Interrupt 1 threshold. Default value: 000 0000
INT1_DURATION (33h)
Table 53.
INT1_DURATION register
0
Table 54.
D6
D5
D4
D3
INT1_DURATION description
D6 - D0
Duration value. Default value: 000 0000
D6 - D0 bits set the minimum duration of the Interrupt 1 event to be recognized. Duration
steps and maximum values depend on the ODR chosen.
8.25
CLICK_CFG (38h)
Table 55.
--
36/42
CLICK_CFG register
--
ZD
ZS
YD
Doc ID 17530 Rev 1
YS
XD
XS
LIS3DH
Registers description
Table 56.
8.26
CLICK_CFG description
ZD
Enable interrupt double CLICK-CLICK on Z axis. Default value: 0
(0: disable interrupt request; 1: enable interrupt request on measured accel. value
higher than preset threshold)
ZS
Enable interrupt single CLICK-CLICK on Z axis. Default value: 0
(0: disable interrupt request; 1: enable interrupt request on measured accel. value
higher than preset threshold)
YD
Enable interrupt double CLICK-CLICK on Y axis. Default value: 0
(0: disable interrupt request; 1: enable interrupt request on measured accel. value
higher than preset threshold)
YS
Enable interrupt single CLICK-CLICK on Y axis. Default value: 0
(0: disable interrupt request; 1: enable interrupt request on measured accel. value
higher than preset threshold)
XD
Enable interrupt double CLICK-CLICK on X axis. Default value: 0
(0: disable interrupt request; 1: enable interrupt request on measured accel. value
higher than preset threshold)
XS
Enable interrupt single CLICK-CLICK on X axis. Default value: 0
(0: disable interrupt request; 1: enable interrupt request on measured accel. value
higher than preset threshold)
CLICK_SRC (39h)
Table 57.
CLICK_SRC register
IA
Table 58.
DCLICK
SCLICK
Sign
Z
Y
X
CLICK_SRC description
-
-
IA
Interrupt active. Default value: 0
(0: no interrupt has been generated; 1: one or more interrupts have been generated)
DCLICK
Double CLICK-CLICK enable. Default value: 0 (0:double CLICK-CLICK detection disable, 1: double CLICK-CLICK detection enable)
SCLICK
Single CLICK-CLICK enable. Default value: 0 (0:Single CLICK-CLICK detection disable, 1: single CLICK-CLICK detection enable)
Sign
CLICK-CLICK Sign. 0: positive detection, 1: negative detection
Z
Z CLICK-CLICK detection. Default value: 0
(0: no interrupt, 1: Z High event has occurred)
Y
Y CLICK-CLICK detection. Default value: 0
(0: no interrupt, 1: Y High event has occurred)
X
X CLICK-CLICK detection. Default value: 0
(0: no interrupt, 1: X High event has occurred)
Doc ID 17530 Rev 1
37/42
Registers description
8.27
LIS3DH
CLICK_THS (3Ah)
Table 59.
-
Table 60.
CLICK_THS register
Ths6
-
Table 62.
Ths1
Ths0
TLI1
TLI0
TLA1
TLA0
TW1
TW0
TIME_LIMIT register
TLI6
TLI5
TLI4
TLI3
TLI2
TIME_LIMIT description
CLICK-CLICK Time Limit. Default value: 000 0000
TIME_LATENCY (3Ch)
Table 63.
TLA7
Table 64.
TIME_LATENCY register
TLA6
TLA5
TLA4
TLA3
TLA2
TIME_LATENCY description
TLA7-TLA0
CLICK-CLICK time latency. Default value: 000 0000
TIME WINDOW(3Dh)
Table 65.
TW7
Table 66.
TW7-TW0
38/42
Ths2
CLICK-CLICK threshold. Default value: 000 0000
TLI7-TLI0
8.30
Ths3
TIME_LIMIT (3Bh)
Table 61.
8.29
Ths4
CLICK_SRC description
Ths6-Ths0
8.28
Ths5
TIME_WINDOW register
TW6
TW5
TW4
TW3
TIME_WINDOW description
CLICK-CLICK time window
Doc ID 17530 Rev 1
TW2
LIS3DH
9
Package information
Package information
In order to meet environmental requirements, ST offers these devices in different grades of
ECOPACK® packages, depending on their level of environmental compliance. ECOPACK®
specifications, grade definitions and product status are available at: www.st.com.
ECOPACK is an ST trademark.
Doc ID 17530 Rev 1
39/42
Package information
LIS3DH
Table 67.
LGA-16: Mechanical data
mm
Dim
Min.
Typ.
A1
Max.
1
A2
0.785
A3
0.2
D1
2.85
3
3.15
E1
2.85
3
3.15
L1
1
1.06
L2
2
2.06
N1
0.5
N2
1
M
0.04
0.1
P1
0.875
P2
1.275
0.16
T1
0.29
0.35
0.41
T2
0.19
0.25
0.31
d
0.15
k
0.05
Figure 12. LGA-16: Mechanical data and package dimensions
7983231
40/42
Doc ID 17530 Rev 1
LIS3DH
10
Revision history
Revision history
Table 68.
Document revision history
Date
Revision
21-May-2010
1
Changes
Initial release
Doc ID 17530 Rev 1
41/42
LIS3DH
Please Read Carefully:
Information in this document is provided solely in connection with ST products. STMicroelectronics NV and its subsidiaries (“ST”) reserve the
right to make changes, corrections, modifications or improvements, to this document, and the products and services described herein at any
time, without notice.
All ST products are sold pursuant to ST’s terms and conditions of sale.
Purchasers are solely responsible for the choice, selection and use of the ST products and services described herein, and ST assumes no
liability whatsoever relating to the choice, selection or use of the ST products and services described herein.
No license, express or implied, by estoppel or otherwise, to any intellectual property rights is granted under this document. If any part of this
document refers to any third party products or services it shall not be deemed a license grant by ST for the use of such third party products
or services, or any intellectual property contained therein or considered as a warranty covering the use in any manner whatsoever of such
third party products or services or any intellectual property contained therein.
UNLESS OTHERWISE SET FORTH IN ST’S TERMS AND CONDITIONS OF SALE ST DISCLAIMS ANY EXPRESS OR IMPLIED
WARRANTY WITH RESPECT TO THE USE AND/OR SALE OF ST PRODUCTS INCLUDING WITHOUT LIMITATION IMPLIED
WARRANTIES OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE (AND THEIR EQUIVALENTS UNDER THE LAWS
OF ANY JURISDICTION), OR INFRINGEMENT OF ANY PATENT, COPYRIGHT OR OTHER INTELLECTUAL PROPERTY RIGHT.
UNLESS EXPRESSLY APPROVED IN WRITING BY AN AUTHORIZED ST REPRESENTATIVE, ST PRODUCTS ARE NOT
RECOMMENDED, AUTHORIZED OR WARRANTED FOR USE IN MILITARY, AIR CRAFT, SPACE, LIFE SAVING, OR LIFE SUSTAINING
APPLICATIONS, NOR IN PRODUCTS OR SYSTEMS WHERE FAILURE OR MALFUNCTION MAY RESULT IN PERSONAL INJURY,
DEATH, OR SEVERE PROPERTY OR ENVIRONMENTAL DAMAGE. ST PRODUCTS WHICH ARE NOT SPECIFIED AS "AUTOMOTIVE
GRADE" MAY ONLY BE USED IN AUTOMOTIVE APPLICATIONS AT USER’S OWN RISK.
Resale of ST products with provisions different from the statements and/or technical features set forth in this document shall immediately void
any warranty granted by ST for the ST product or service described herein and shall not create or extend in any manner whatsoever, any
liability of ST.
ST and the ST logo are trademarks or registered trademarks of ST in various countries.
Information in this document supersedes and replaces all information previously supplied.
The ST logo is a registered trademark of STMicroelectronics. All other names are the property of their respective owners.
© 2010 STMicroelectronics - All rights reserved
STMicroelectronics group of companies
Australia - Belgium - Brazil - Canada - China - Czech Republic - Finland - France - Germany - Hong Kong - India - Israel - Italy - Japan Malaysia - Malta - Morocco - Philippines - Singapore - Spain - Sweden - Switzerland - United Kingdom - United States of America
www.st.com
42/42
Doc ID 17530 Rev 1