SCES381E − JANUARY 2002 − REVISED SEPTEMBER 2003 D Available in the Texas Instruments D D D D D D D D D D DBV OR DCK PACKAGE (TOP VIEW) NanoStar and NanoFree Packages Supports 5-V VCC Operation Inputs Accept Voltages to 5.5 V Max tpd of 5.4 ns at 3.3 V Low Power Consumption, 10-µA Max ICC ±24-mA Output Drive at 3.3 V Typical VOLP (Output Ground Bounce) <0.8 V at VCC = 3.3 V, TA = 25°C Typical VOHV (Output VOH Undershoot) >2 V at VCC = 3.3 V, TA = 25°C Ioff Supports Partial-Power-Down Mode Operation Latch-Up Performance Exceeds 100 mA Per JESD 78, Class II ESD Protection Exceeds JESD 22 − 2000-V Human-Body Model (A114-A) − 1000-V Charged-Device Model (C101) 1A GND 2A 1 6 2 5 3 4 1Y VCC 2Y YEA, YEP, YZA, OR YZP PACKAGE (BOTTOM VIEW) 2A GND 1A 3 4 2 5 1 6 2Y VCC 1Y description/ordering information This dual Schmitt-trigger buffer is designed for 1.65-V to 5.5-V VCC operation. The SN74LVC2G17 contains two buffers and performs the Boolean function Y = A. The device functions as two independent buffers, but because of Schmitt action, it may have different input threshold levels for positive-going (VT+) and negative-going (VT−) signals. ORDERING INFORMATION NanoStar − WCSP (DSBGA) 0.17-mm Small Bump − YEA SN74LVC2G17YEAR NanoFree − WCSP (DSBGA) 0.17-mm Small Bump − YZA (Pb-free) SN74LVC2G17YZAR NanoStar − WCSP (DSBGA) 0.23-mm Large Bump − YEP −40 C to 85°C 85 C −40°C ORDERABLE PART NUMBER PACKAGE† TA Reel of 3000 SOT (SC-70) − DCK _ _ _C7_ SN74LVC2G17YEPR NanoFree − WCSP (DSBGA) 0.23-mm Large Bump − YZP (Pb-free) SOT (SOT-23) − DBV TOP-SIDE MARKING‡ SN74LVC2G17YZPR Reel of 3000 SN74LVC2G17DBVR Reel of 250 SN74LVC2G17DBVT Reel of 3000 SN74LVC2G17DCKR Reel of 250 SN74LVC2G17DCKT C17_ C7_ † Package drawings, standard packing quantities, thermal data, symbolization, and PCB design guidelines are available at www.ti.com/sc/package. ‡ DBV/DCK: The actual top-side marking has one additional character that designates the assembly/test site. YEA/YZA, YEP/YZP: The actual top-side marking has three preceding characters to denote year, month, and sequence code, and one following character to designate the assembly/test site. Pin 1 identifier indicates solder-bump composition (1 = SnPb, • = Pb-free). Please be aware that an important notice concerning availability, standard warranty, and use in critical applications of Texas Instruments semiconductor products and disclaimers thereto appears at the end of this data sheet. NanoStar and NanoFree are trademarks of Texas Instruments. Copyright 2003, Texas Instruments Incorporated ! " #$%! " &$'(#! )!%* )$#!" # ! "&%##!" &% !+% !%" %," "!$%!" "!)) -!.* )$#! &#%""/ )%" ! %#%""(. #($)% !%"!/ (( &%!%"* POST OFFICE BOX 655303 • DALLAS, TEXAS 75265 1 SCES381E − JANUARY 2002 − REVISED SEPTEMBER 2003 description/ordering information (continued) NanoStar and NanoFree package technology is a major breakthrough in IC packaging concepts, using the die as the package. This device is fully specified for partial-power-down applications using Ioff. The Ioff circuitry disables the outputs, preventing damaging current backflow through the device when it is powered down. FUNCTION TABLE (each inverter) INPUT A OUTPUT Y H H L L logic diagram (positive logic) 1A 2A 1 6 3 4 1Y 2Y absolute maximum ratings over operating free-air temperature range (unless otherwise noted)† Supply voltage range, VCC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . −0.5 V to 6.5 V Input voltage range, VI (see Note 1) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . −0.5 V to 6.5 V Voltage range applied to any output in the high-impedance or power-off state, VO (see Note 1) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . −0.5 V to 6.5 V Voltage range applied to any output in the high or low state, VO (see Notes 1 and 2) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . −0.5 V to VCC + 0.5 V Input clamp current, IIK (VI < 0) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . −50 mA Output clamp current, IOK (VO < 0) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . −50 mA Continuous output current, IO . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ±50 mA Continuous current through VCC or GND . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ±100 mA Package thermal impedance, θJA (see Note 3): DBV package . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 165°C/W DCK package . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 259°C/W YEA/YZA package . . . . . . . . . . . . . . . . . . . . . . . . . . . 143°C/W YEP/YZP package . . . . . . . . . . . . . . . . . . . . . . . . . . . 123°C/W Storage temperature range, Tstg . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . −65°C to 150°C † Stresses beyond those listed under “absolute maximum ratings” may cause permanent damage to the device. These are stress ratings only, and functional operation of the device at these or any other conditions beyond those indicated under “recommended operating conditions” is not implied. Exposure to absolute-maximum-rated conditions for extended periods may affect device reliability. NOTES: 1. The input negative-voltage and output voltage ratings may be exceeded if the input and output current ratings are observed. 2. The value of VCC is provided in the recommended operating conditions table. 3. The package thermal impedance is calculated in accordance with JESD 51-7. 2 POST OFFICE BOX 655303 • DALLAS, TEXAS 75265 SCES381E − JANUARY 2002 − REVISED SEPTEMBER 2003 recommended operating conditions (see Note 4) Operating MIN MAX UNIT VCC VI Supply voltage 1.65 5.5 V Input voltage 0 5.5 V VO Output voltage 0 VCC −4 V VCC = 1.65 V VCC = 2.3 V IOH High-level output current VCC = 3 V VCC = 4.5 V VCC = 1.65 V VCC = 2.3 V IOL −8 −16 −32 4 8 16 Low-level output current mA −24 VCC = 3 V 24 VCC = 4.5 V 32 mA TA Operating free-air temperature −40 85 °C NOTE 4: All unused inputs of the device must be held at VCC or GND to ensure proper device operation. Refer to the TI application report, Implications of Slow or Floating CMOS Inputs, literature number SCBA004. POST OFFICE BOX 655303 • DALLAS, TEXAS 75265 3 SCES381E − JANUARY 2002 − REVISED SEPTEMBER 2003 electrical characteristics over recommended operating free-air temperature range (unless otherwise noted) PARAMETER TEST CONDITIONS VT+ Positive-going input threshold voltage VT− Negative-going input threshold voltage ∆VT Hysteresis (VT+ − VT−) MIN 1.65 V 0.7 1.4 2.3 V 1 1.7 3V 1.3 2.2 1.9 3.1 5.5 V 2.2 3.7 1.65 V 0.3 0.7 2.3 V 0.4 1 3V 0.6 1.3 4.5 V 1.1 2 5.5 V 1.4 2.5 1.65 V 0.3 0.8 2.3 V 0.4 0.9 3V 0.4 1.1 4.5 V 0.6 1.3 0.7 1.4 IOH = −100 µA IOH = −4 mA 1.65 V to 5.5 V 1.65 V VCC−0.1 1.2 IOH = −8 mA IOH = −16 mA 2.3 V 1.9 II Ioff ICC ∆ICC A input 1.65 V to 5.5 V 0.1 1.65 V 0.45 IOL = 8 mA IOL = 16 mA 2.3 V 0.3 0.4 3V 0 1.65 V to 5.5 V 3 V to 5.5 V Ci VI = VCC or GND † All typical values are at VCC = 3.3 V, TA = 25°C. V 0.55 0 to 5.5 V IO = 0 Other inputs at VCC or GND V 0.55 4.5 V VI = 5.5 V or GND, One input at VCC − 0.6 V, V 3.8 IOL = 100 µA IOL = 4 mA VI = 5.5 V or GND VI or VO = 5.5 V V 2.3 4.5 V IOL = 24 mA IOL = 32 mA UNIT V 2.4 3V IOH = −24 mA IOH = −32 mA VOL MAX 4.5 V 5.5 V VOH TYP† VCC 3.3 V ±5 µA ±10 µA 10 µA 500 µA 4 pF switching characteristics over recommended operating free-air temperature range (unless otherwise noted) (see Figure 1) PARAMETER tpd 4 FROM (INPUT) TO (OUTPUT) A Y VCC = 1.8 V ± 0.15 V VCC = 2.5 V ± 0.2 V VCC = 3.3 V ± 0.3 V VCC = 5 V ± 0.5 V MIN MAX MIN MAX MIN MAX MIN MAX 3.9 9.3 1.9 5.7 2.2 5.4 1.5 4.3 POST OFFICE BOX 655303 • DALLAS, TEXAS 75265 UNIT ns SCES381E − JANUARY 2002 − REVISED SEPTEMBER 2003 operating characteristics, TA = 25°C PARAMETER Cpd Power dissipation capacitance TEST CONDITIONS f = 10 MHz POST OFFICE BOX 655303 VCC = 1.8 V TYP VCC = 2.5 V TYP 17 • DALLAS, TEXAS 75265 18 VCC = 3.3 V TYP 19 VCC = 5 V TYP 21 UNIT pF 5 SCES381E − JANUARY 2002 − REVISED SEPTEMBER 2003 PARAMETER MEASUREMENT INFORMATION RL From Output Under Test CL (see Note A) VLOAD Open S1 GND RL TEST S1 tPLH/tPHL tPLZ/tPZL tPHZ/tPZH Open VLOAD GND LOAD CIRCUIT INPUTS VCC 1.8 V ± 0.15 V 2.5 V ± 0.2 V 3.3 V ± 0.3 V 5 V ± 0.5 V VI tr/tf VCC VCC 3V VCC ≤2 ns ≤2 ns ≤2.5 ns ≤2.5 ns VM VLOAD CL RL V∆ VCC/2 VCC/2 1.5 V VCC/2 2 × VCC 2 × VCC 6V 2 × VCC 30 pF 30 pF 50 pF 50 pF 1 kΩ 500 Ω 500 Ω 500 Ω 0.15 V 0.15 V 0.3 V 0.3 V VI Timing Input VM 0V tw tsu VI Input VM VM th VI Data Input VM VM 0V 0V VOLTAGE WAVEFORMS PULSE DURATION VOLTAGE WAVEFORMS SETUP AND HOLD TIMES VI VM Input VM 0V tPLH tPHL VOH VM Output VM VOL tPHL Output Waveform 1 S1 at VLOAD (see Note B) tPLH VM VM VM 0V tPZL tPLZ VLOAD/2 VM tPZH VOH Output VI Output Control VM VOL VOLTAGE WAVEFORMS PROPAGATION DELAY TIMES INVERTING AND NONINVERTING OUTPUTS Output Waveform 2 S1 at GND (see Note B) VOL + V∆ VOL tPHZ VM VOH − V∆ VOH ≈0 V VOLTAGE WAVEFORMS ENABLE AND DISABLE TIMES LOW- AND HIGH-LEVEL ENABLING NOTES: A. CL includes probe and jig capacitance. B. Waveform 1 is for an output with internal conditions such that the output is low except when disabled by the output control. Waveform 2 is for an output with internal conditions such that the output is high except when disabled by the output control. C. All input pulses are supplied by generators having the following characteristics: PRR ≤ 10 MHz, ZO = 50 Ω. D. The outputs are measured one at a time with one transition per measurement. E. tPLZ and tPHZ are the same as tdis. F. tPZL and tPZH are the same as ten. G. tPLH and tPHL are the same as tpd. H. All parameters and waveforms are not applicable to all devices. Figure 1. Load Circuit and Voltage Waveforms 6 POST OFFICE BOX 655303 • DALLAS, TEXAS 75265 MECHANICAL DATA MPDS114 – FEBRUARY 2002 DCK (R-PDSO-G6) PLASTIC SMALL-OUTLINE PACKAGE 0,30 0,15 0,65 6 0,10 M 4 1,40 1,10 1 0,13 NOM 2,40 1,80 3 Gage Plane 2,15 1,85 0,15 0°–8° 0,46 0,26 Seating Plane 1,10 0,80 0,10 0,00 0,10 4093553-3/D 01/02 NOTES: A. B. C. D. All linear dimensions are in millimeters. This drawing is subject to change without notice. Body dimensions do not include mold flash or protrusion. Falls within JEDEC MO-203 POST OFFICE BOX 655303 • DALLAS, TEXAS 75265 IMPORTANT NOTICE Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, modifications, enhancements, improvements, and other changes to its products and services at any time and to discontinue any product or service without notice. Customers should obtain the latest relevant information before placing orders and should verify that such information is current and complete. All products are sold subject to TI’s terms and conditions of sale supplied at the time of order acknowledgment. TI warrants performance of its hardware products to the specifications applicable at the time of sale in accordance with TI’s standard warranty. Testing and other quality control techniques are used to the extent TI deems necessary to support this warranty. Except where mandated by government requirements, testing of all parameters of each product is not necessarily performed. TI assumes no liability for applications assistance or customer product design. Customers are responsible for their products and applications using TI components. To minimize the risks associated with customer products and applications, customers should provide adequate design and operating safeguards. TI does not warrant or represent that any license, either express or implied, is granted under any TI patent right, copyright, mask work right, or other TI intellectual property right relating to any combination, machine, or process in which TI products or services are used. Information published by TI regarding third-party products or services does not constitute a license from TI to use such products or services or a warranty or endorsement thereof. Use of such information may require a license from a third party under the patents or other intellectual property of the third party, or a license from TI under the patents or other intellectual property of TI. Reproduction of information in TI data books or data sheets is permissible only if reproduction is without alteration and is accompanied by all associated warranties, conditions, limitations, and notices. Reproduction of this information with alteration is an unfair and deceptive business practice. TI is not responsible or liable for such altered documentation. Resale of TI products or services with statements different from or beyond the parameters stated by TI for that product or service voids all express and any implied warranties for the associated TI product or service and is an unfair and deceptive business practice. TI is not responsible or liable for any such statements. Following are URLs where you can obtain information on other Texas Instruments products and application solutions: Products Amplifiers Applications amplifier.ti.com Audio www.ti.com/audio Data Converters dataconverter.ti.com Automotive www.ti.com/automotive DSP dsp.ti.com Broadband www.ti.com/broadband Interface interface.ti.com Digital Control www.ti.com/digitalcontrol Logic logic.ti.com Military www.ti.com/military Power Mgmt power.ti.com Optical Networking www.ti.com/opticalnetwork Microcontrollers microcontroller.ti.com Security www.ti.com/security Telephony www.ti.com/telephony Video & Imaging www.ti.com/video Wireless www.ti.com/wireless Mailing Address: Texas Instruments Post Office Box 655303 Dallas, Texas 75265 Copyright 2003, Texas Instruments Incorporated