LNB Supply and Control Voltage Regulator A8285SlB SOIC Scale 1:1 A8287SlB SOIC Scale 1:1 SCL 1 16 VCP SDA 2 15 BOOST LX IRQ 3 14 GND 4 13 GND VREG 5 12 LNB VIN 6 11 TOUT EXTM 7 10 TCAP ADD 8 9 NC SCL 1 24 VCP SDA 2 23 BOOST IRQ 3 22 GND 4 21 GND GND GND 5 20 LX GND 6 19 GND GND 7 18 VREG 8 17 GND LNB VIN EXTM ADD 9 16 TOUT 10 15 11 14 TCAP NC TDO 12 13 TDI ABSOLUTE MAXIMUM RATINGS Load Supply Voltage, VIN....................................16 V Output Current, IOUT ..................Internally Limited* Output Voltage LNB, BOOST .....................–0.3 V to 28 V TOUT ................................. –0.3 V to 22 V Logic Input EXTM ...................................–0.3 V to 5 V Other .................................... –0.3 V to 7 V Logic Output ........................................ –0.3 V to 7 V Package Power Dissipation ………..See power dissipation information in the Application Information section Operating Temperature Ambient, TA .......................–20°C to +85°C Junction, TJ.......................–20°C to +150°C Storage,TS .......................–55°C to +150°C * Output current rating may be limited by duty cycle, ambient temperature, and heat sinking. Under any set of conditions, do not exceed the specified current rating or a junction temperature of +150°C. Intended for analog and digital satellite receivers, the LNB (low noise block) converter regulator is a monolithic linear and switching voltage regulator, specifically designed to provide power and interface signals to an LNB downconverter, via coaxial cable. The device uses a 2-wire bidirectional serial interface, compatible with the I2C (Inter-C bus) standard, that operates up to 400 kHz. The A8285 is supplied in a 16-lead plastic power SOIC with copper batwing tabs (suffix LB). The A8287 is supplied in a 24-lead plastic power SOIC with copper batwing tabs (part number suffix LB). FEATURES LNB selection and standby function Provides up to 500 mA load current Two-wire serial I2C interface Built-in tone oscillator, factory-trimmed to 22 kHz; facilitates DiSEqC™ 2.0 encoding Auxiliary modulation input 22 kHz tone detector facilitates DiSEqC™ decoding (A8287 only) Tracking switch-mode power converter for lowest dissipation LNB overcurrent protection and diagnostics Internal overtemperature protection LNB voltages (16 possible levels) compatible with all common standards Use the following complete part numbers when ordering: Part Number Package Description A8287SLB 24-pin, batwing SOIC All features A8285SLB 16-pin, batwing SOIC Tone detect not provided Data Sheet 27448.003c A8285/A8287 Preliminary Data Sheet Subject to Change without Notice January 21, 2004 Data Sheet Preliminary 27448.003c A8285/A8287 LNB Supply and Control Voltage Regulator Functional Block Diagram V IN C10 L1 C1 33 uF 100 nF VREG Internal Regulator 220 nF C5 33 uH VIN C3 D1 C2 VCP BOOST Feedback 100 uF 100 nF 100 nF LX C4 BOOST Charge Pump OSC In VPUMP Boost Converter Overcurrent OSC DISABLE 100 mV EXTM Clock Divider R3 R4 R5 VDD L2 220 uH LNB 22 kHz Tone Generator Tracking Regulator SDA SCL R1 15 Ω D2 220 nF C7 220 nF C6 TCAP Output Voltage Select 2 I C Interface ADD 6.8 nF C8 GM TOUT 220Ω R2 TDI IRQ Fault Monitor Overcurrent TSD Undervoltage Overcurrent 10 nF C9 22 kHz Tone Detector R6 VDD TDO Tone detector and leads TDI and TDO are not provided in 16-pin package (A8285). ID C1 C2, C5,C10 C4 C3,C6,C7 Characteristics Suggested Manufacturer 33 µF, 25 V, esr < 200 mΩ, Iripple > 350 mA 100 nF, 50 V, X5R or X7R 100 µF, 35 V, esr < 75 mΩ, Iripple> 800 mA Nichicon, part number UHC1V101MPT 220 nF, 50 V, X5R or X7R C8 6.8 nF, 50 V; Y5V, X5R, or X7R C9 10 nF (maximum), 50 V; Y5V, X5R, or X7R R1 15 Ω, 1%, c W R2 220 Ω, 1%, 2 W R3-R6 Nichicon, part number UHC1E330MET Value determined by VDD, bus capacitance. etc. L1 33 µH, IDC > 1.3 A L2 220 µH, IDC > 0.5 A TDK, part number TSL0808-330K1R4; Coilcraft, part number DR0810-333 TDK, part number TSL0808-221KR54; Coilcraft, part number DR0810-224 D1 1 A, 35 V or 40 V, Schottky diode Various, part number 1N5819; Sanken, part number AW04 D2 1 A, 100 V, 1N4002 www.allegromicro.com 115 Northeast Cutoff, Box 15036 Worcester, Massachusetts 01615-0036 (508) 853-5000 2 Data Sheet Preliminary 27448.003c A8285/A8287 LNB Supply and Control Voltage Regulator ELECTRICAL CHARACTERISTICS at TA = +25°C, VIN = 10 to 16 V (unless otherwise noted) Characteristics Set-point Accuracy, load and line regulation Supply Current Boost Switch-On Resistance Symbol Test Conditions Min. Typ. Max. Units -4.5 0 4.5 % VO1 Relative to target voltage selected, with: ILOAD = 0 to 500 mA ICC ENB = Low, LNB output disabled – – 7 mA ENB = High, LNB output enabled, ILOAD = 0mA – – 15 mA – 400 500 mΩ ICCEN RDSBOOST TJ = 25 °C, ILOAD = 500mA Switching Frequency fo – 320 352 384 kHz Switch Current Limit – VIN = 12 V 2.0 3 4.0 A VBOOST – VLNB, no tone signal, ILOAD = 500 mA 400 600 800 mV –12.5 –10 –7.5 µA 7.5 10 12.5 µA Linear Regulator Voltage Drop Slew Rate Current on TCAP ∆VREG ICAP Charging Discharging Output Voltage Slew Period tslew VLNB = 13 to 18 V, TCAP = 6.8 nF, ILOAD = 500 mA – 500 – µs Output Reverse Current IOR ENB = Low, VLNB = 28 V with C4 fully charged – 1 5 mA Ripple and Noise on LNB Output VRN See notes 1 and 2 – – 50 mVpp Overcurrent Limit ILIM High limit Low limit 550 400 700 500 850 600 mA mA Overcurrent Disable Time tDIS – 1.2 – 1.7 ms Protection Circuitry VIN Undervoltage Threshold UVOFF Guaranteed turn-off 8.65 9.15 9.65 V VIN Turn-On Threshold UVON Guaranteed turn-on 8.75 9.25 9.75 V Power-Not-Good Flag Set PNGset – 77 85 93 %VLNB Power-Not-Good Flag Reset PNGreset – 82 90 98 %VLNB Thermal Shutdown Threshold TJ See note 1 – 165 – °C Thermal Shutdown Hysteresis ∆TJ See note 1 – 20 – °C Continued on next page www.allegromicro.com 115 Northeast Cutoff, Box 15036 Worcester, Massachusetts 01615-0036 (508) 853-5000 3 Data Sheet Preliminary 27448.003c A8285/A8287 LNB Supply and Control Voltage Regulator ELECTRICAL CHARACTERISTICS (continued) at TA = +25°C, VIN = 10 to 16 V (unless otherwise noted) Characteristics Symbol Test Conditions Min. Typ. Max. Units Tone Characteristics Tone Frequency fTONE – 20 22 24 kHz Tone Pull-Down Current ITONE – 30 40 50 mA Tone Turn-On and Turn-Off Delays tDEL Using EXTM pin – – 1 µs VIH – 2 – – V Input Leakage VIL IIL – – – –1 – – 0.8 1 V µA Tone Detector Input Amplitude VTDI fIN = 22 kHz 260 – 1000 mV Tone Detector Frequency Capture fTDI 600 mVpp sinewave 17.6 – 26.4 kHz Tone Detector Input Impedance ZTDI See note 1 – 8.6 – kΩ Tone Detector Output Voltage VOL Tone present, ILOAD = 3 mA – – 0.4 V Tone Detector Output Leakage IOL Tone absent, VO = 7 V – – 10 µA Logic Input (SDA,SCL) Low Level VIL – – – 0.8 V Logic Input (SDA,SCL) High Level VIH – 2 – – V VHYS – – 150 – mV –10 <±1.0 10 µA External Tone Logic Input I C Interface 2 Input Hysteresis Logic Input Current IIN VIN = 0 V to 7 V Output Voltage (SDA, IRQ) VOL ILOAD = 3 mA – – 0.4 V Output Leakage (SDA, IRQ) IOL VO = 0 V to 7 V – – 10 µA SCL Clock Frequency fCLK – 0 – 400 kHz Output Fall Time tOF VIH to VIL – – 250 ns Bus Free Time Between Stop and Start tBUF See I2C Interface Timing Diagram 1.3 – – µs Hold Time for Start Condition tHD:STA See I2C Interface Timing Diagram 0.6 – – µs Setup Time for Start Condition tSU:STA See I2C Interface Timing Diagram 0.6 – – µs SCL Low Time tLOW See I C Interface Timing Diagram 1.3 – – µs SCL High Time tHIGH See I C Interface Timing Diagram 0.6 – – µs 100 – – ns 2 2 Data Setup Time tSU:DAT See note1; I C Interface Timing Diagram Data Hold Time tHD:DAT See I C Interface Timing Diagram 0 – 900 ns Setup Time for Stop Condition tSU:STO See I C Interface Timing Diagram 0.6 – – µs 2 2 2 Continued on next page www.allegromicro.com 115 Northeast Cutoff, Box 15036 Worcester, Massachusetts 01615-0036 (508) 853-5000 4 Data Sheet Preliminary 27448.003c A8285/A8287 LNB Supply and Control Voltage Regulator ELECTRICAL CHARACTERISTICS (continued) at TA = +25°C, VIN = 10 to 16 V (unless otherwise noted) Characteristics Symbol Test Conditions Min. Typ. Max. Units ADD Voltage for Address 0001,000 Address1 – 0 – 0.7 V ADD Voltage for Address 0001,001 Address2 – 1.3 – 1.7 V ADD Voltage for Address 0001,010 Address3 – 2.3 – 2.7 V ADD Voltage for Address 0001,011 Address4 – 3.3 – 5 V I2C Address Setting 1 Guaranteed by design. 2 Use recommended components and adhere to layout guidelines. I2C Interface Timing Diagram tSU:STA tHD:STA tSU:DAT tHD:DAT tSU:STO tBUF SDA SCL tLOW tHIGH www.allegromicro.com 115 Northeast Cutoff, Box 15036 Worcester, Massachusetts 01615-0036 (508) 853-5000 5 Data Sheet Preliminary 27448.003c A8285/A8287 LNB Supply and Control Voltage Regulator Functional Description Boost Converter/Linear Regulator. A current-mode boost converter provides the tracking regulator a supply voltage that tracks the requested LNB output voltage. The converter operates at 16 times the internal tone frequency, 352 kHz nominal. The tracking regulator provides minimum power dissipation across the range of output voltages, assuming the input voltage is less than the output voltage, by adjusting the BOOST pin voltage 600 mV nominal above the LNB output voltage selected. Under conditions where the input voltage is greater than the output voltage, the tracking regulator must drop the differential voltage. When operating in this condition, care must be taken to ensure that the safe operating temperature range of the A8285/A8287 is not exceeded. For additional information, see Power Dissipation in the Application Information section. Note: To conserve power at light loads, the boost converter operates in a pulse-skipping mode. Overcurrent Protection. The A8285/A8287 is protected against both overcurrent and short circuit conditions by limiting the output current to ILIM . In the event of an overcurrent, the current limit can be applied indefinitely. Alternatively, if the ODT feature is enabled, and the fault current appears for longer than the disable time tDIS, then the device is turned off. The device can be enabled again via the I2C interface. If the overcurrent is removed before the disable time has elapsed, the device remains functioning. These settings are made in the Control register and the Status register. Charge Pump. Generates a supply voltage above the internal tracking regulator output to drive the linear regulator control. Slew Rate Control. During either start-up or when the output voltage on the BOOST pin is being changed, the output voltage rise and fall times can be programmed by an external capacitor located on the TCAP pin. Note that during start-up, the BOOST pin is precharged to the input voltage minus a diode drop. As a result, the slew rate control occurs from this point. The value for TCAP can be calculated using the following formula: TCAP = (ICAP 8) / (∆V/s) × where ∆V/s is required slew rate. The smallest value for TCAP is 2.2 nF. Modulation is unaffected by the choice of TCAP. If limiting LNB output voltage rise and fall times is not required, the TCAP terminal must have a value of at least a 2.2 nF to minimize output noise. External Tone Modulation. To improve design flexibility and to allow implementation of proposed LNB remote control standards, the logic modulation input pin EXTM is provided. The logic signal supplied to this pin creates a 650 mV ±250 mV tone signal on the TOUT pin by controlling a 40 mA current pull-down device through the DiSEqC™ filter. The shape of the tone waveform depends on the filter components used and the LNB/cable capacitance. Tone Detection. A 22 kHz tone envelope detector is provided in the A8287 solution. The detector extracts the tone signal and provides it as an open-collector signal on the TDO pin. The maximum tone out error is ±1 tone cycle, and the maximum tone out delay with respect to the input is ±1 tone cycle. Control Register. The main functions of the A8285/ A8287 are controlled via the I2C interface by writing to the control register. The power-up states for the control functions are all zero. Control functions include the following: • Internal Tone Modulation Enable (ENT). When the ENT bit is set to 1, the internal tone generator controls a 40 mA pull-down device, thus creating the tone signal after the DiSEqC™ filter in a way identical to the EXTM scheme. The internal oscillator is factory-trimmed to provide a tone of 22 ±2 kHz. No further adjustment is required. Burst coding of the 22 kHz tone is accomplished due to the fast response of the serial command and rapid tone response. This allows implementation of the DiSEqC™ 2.0 protocols. • Select Output Voltage Amplitude (VSEL0, VSEL1, VSEL2, VSEL3). The LNB output voltage can be programmed to a particular voltage according to the Output Voltage Amplitude Selection table shown on the following page. • Enable (ENB). When set to 1, the LNB output is enabled. When reset to 0, the LNB output is disabled. • Overcurrent Limit (ILIM). Selects the output overcurrent limit. When set to 0, the limit is 500 mA. When set to 1, the limit is 700 mA. • Overcurrent Disable Time (ODT). When set to 1, in the event of an overcurrent occuring for a duration exceeding the disable time, the device is turned off. When set to 0, www.allegromicro.com 115 Northeast Cutoff, Box 15036 Worcester, Massachusetts 01615-0036 (508) 853-5000 6 Data Sheet Preliminary 27448.003c A8285/A8287 LNB Supply and Control Voltage Regulator this feature is disabled and the device is not turned off during an overcurrent. Status Register. The status of the A8285/A8287 read register can be interrogated by the system master controller via the I2C interface. Status functions include the following: • Undervoltage Lockout (VUV). When the input voltage (VIN) drops below the undervoltage threshold, the undervoltage bit VUV is set, disabling the output. • Power Not Good (PNG). When the LNB output is enabled, and the LNB output is below 85% of the programmed LNB voltage, the PNG bit is set. • Disable (DIS). Provides the status of the LNB output. When set, this indicates that the output is disabled, either intentionally or by a fault. • Thermal Shutdown (TSD). When the junction temperature exceeds the maximum threshold, the thermal shutdown bit is set, which disables the LNB output. DIS also is set. • Overcurrent (OCP). This disables LNB output when an overcurrent appears on the LNB output for a period greater than the ODT (ODT must be enabled for this feature to take effect). In addition, the DIS bit is set. Note: If an overcurrent occurs and ODT is disabled, the A8285/A8287 will operate in current limit indefininitely and the OCP bit will not be set. IRQ Flag. The IRQ flag is activated when any fault condition occurs, including: thermal shutdown, overcurrent, undervoltage, or the occurrence of a power-up sequence. Note that the IRQ flag is not activated when either (a) the channel is disabled (DIS), as it may have been disabled intentionally by the master controller, or (b) if PNG is active, as the A8285/A8287 may be starting up. Fault conditions are stored in the status registers. Also note that the IRQ flag will not activate when an overcurrent occurs and ODT is disabled. In this condition, the device operates within ILIM. Output Voltage Amplitude Selection Table VSEL3 VSEL2 VSEL1 VSEL0 LNB (V) 0 0 0 0 12.709 0 0 0 1 13.042 0 0 1 0 13.375 0 0 1 1 13.709 0 1 0 0 14.042 0 1 0 1 14.375 0 1 1 0 14.709 0 1 1 1 15.042 1 0 0 0 18.042 1 0 0 1 18.375 1 0 1 0 18.709 1 0 1 1 19.042 1 1 0 0 19.375 1 1 0 1 19.709 1 1 1 0 20.042 1 1 1 1 20.375 When VIN is initially applied to the A8285/A8285, the VUV bit is set, indicating that an undervoltage condition has occurred. When the IRQ flag is activated during either of the above fault conditions, and the system master controller addresses the A8285/A8287 with the read/write bit set to 1, then the IRQ flag is reset once the A8285/A8287 acknowledges the address. When the master controller reads the data and is acknowledged, the status registers are updated. If the fault is removed, the A8285/A8287 is again ready for operation (being re-enabled via a write command). Otherwise, the controller can keep polling the A8285/A8287 until the fault is removed. When VIN, is initially applied to the A8285/A8285, the I2C interface will not function until the internal logic supply VREG has reached its operating level. Once VREG is within tolerance, the VUV bit in the status register is set and the IRQ is activated to inform the master controller of this condition. (The IRQ is effectively acting as a power-up flag.) The IRQ is reset when the A8285/A8287 acknowledges the address. Once the master has read the status registers, the VUV bit is reset. The device is then ready for operation. I2C Interface. This is a serial interface that uses two bus lines, SCL and SDA, to access the internal Control and Status registers of the A8285/A8287. Data is exchanged between a microcontroller (master) and the A8285/A8287 (slave). The clock input to SCL is generated by the master, while SDA functions as either an input or an open drain output, depending on the direction of the data. www.allegromicro.com 115 Northeast Cutoff, Box 15036 Worcester, Massachusetts 01615-0036 (508) 853-5000 7 Data Sheet Preliminary 27448.003c A8285/A8287 LNB Supply and Control Voltage Regulator Application Information to occur at any time during a data transfer. The A8285/A8287 always responds by resetting the data transfer sequence. Timing Considerations The control sequence of the communication through the I2C interface is composed of several steps in sequence: 1. Start Condition. Defined by a negative edge on the SDA line, while SCL is high. 2. Address Cycle. 7 bits of address, plus 1 bit to indicate read (1) or write (0), and an acknowledge bit. The first five bits of the address are fixed as: 00010. The four optional addresses, defined by the remaining two bits, are selected by the ADD input. The address is transmitted MSB first. 3. Data Cycles. 8 bits of data followed by an acknowledge bit. Multiple data bytes can be read. Data is transmitted MSB first. 4. Stop Condition. Defined by a positive edge on the SDA line, while SCL is high. Except to indicate a Start or Stop condition, SDA must be stable while the clock is high. SDA can only be changed while SCL is low. It is possible for the Start or Stop condition The Read/Write bit is used to determine the data transfer direction. If the Read/Write bit is high, the master reads one or more bytes from the A8285/A8287. If the Read/Write bit is low, the master writes one byte to the A8285/A8287. Note that multiple writes are not permitted. All write operations must be preceded with the address. The Acknowledge bit has two functions. It is used by the master to determine if the slave device is responding to its address and data, and it is used by the slave when the master is reading data back from the slave. When the A8285/A8287 decodes the 7-bit address field as a valid address, it responds by pulling SDA low during the ninth clock cycle. During a data write from the master, the A8285/A8287 also pulls SDA low during the clock cycle that follows the data byte, in order to indicate that the data has been successfully received. In both cases, the master device must release the acknowledge from LNBR Writing to the Register Start Address W Control Data SDA 0 0 0 1 0 A1 A0 0 AK SCL 1 2 3 4 5 6 7 8 9 Reading One Byte from the Register Start acknowledge from LNBR D7 D6 D5 D4 D3 Stop D2 D1 D0 acknowledge from LNBR Address AK no acknowledge from master R Status Data SDA 0 0 0 1 0 A1 A0 1 AK SCL 1 2 3 4 5 6 7 8 9 D7 D6 D5 D4 D3 Stop D2 D1 D0 NAK Reading Multiple Bytes from the Register acknowledge from LNBR Start Address no acknowledge from master acknowledge from master R Status Data SDA 0 0 0 1 0 A1 A0 1 AK SCL 1 2 3 4 5 6 7 8 9 D7 D6 D5 D4 D3 Status Data D2 D1 D0 AK D7 D6 D5 D4 D3 Stop D2 D1 www.allegromicro.com 115 Northeast Cutoff, Box 15036 Worcester, Massachusetts 01615-0036 (508) 853-5000 D0 NAK 8 Data Sheet Preliminary 27448.003c A8285/A8287 LNB Supply and Control Voltage Regulator SDA line before the ninth clock cycle, in order to allow this handshaking to occur. register are defined such that the all-zero condition indicates that the A8285/A8287 is fully active with no fault conditions. During a data read, the A8285/A8287 acknowledges the address in the same way as in the data write sequence, and then retains control of the SDA line and send the data to the master. On completion of the eight data bits, the A8285/ A8287 releases the SDA line before the ninth clock cycle, in order to allow the master to acknowledge the data. If the master holds the SDA line low during this Acknowledge bit, the A8285/A8287 responds by sending another data byte to the master. Data bytes continue to be sent to the master until the master releases the SDA line during the Acknowledge bit. When this is detected, the A8285/A8287 stops sending data and waits for a stop signal. When VIN is initially applied, the I2C interface does not respond to any requests until the internal logic supply VREG has reached its operating level. Once VREG has reached this point, the IRQ output goes active, and the VUV bit is set. After the A8285/A8287 acknowledges the address, the IRQ flag is reset. Once the master reads the status registers, the registers are updated with the VUV reset. Control Register (I2C Write Register). All main functions of the A8285/A8287 are controlled through the I2C interface via the 8-bit Control register. This register allows selection of the output voltage and current limit, enabling and disabling the LNB output, and switching the 22 kHz tone on and off. The power-up state is 0 for all of the control functions. Interrupt Request. The A8285/A8287 also provides an interrupt request pin IRQ, which is an open-drain, activelow output. This output may be connected to a common IRQ line with a suitable external pull-up and can be used with other I2C devices to request attention from the master controller. The IRQ output becomes active when either the A8285/A8287 first recognizes a fault condition, or at poweron when the main supply VIN and the internal logic supply VREG reach the correct operating conditions. It is only reset to inactive when the I2C master addresses the A8285/A8287 with the Read/Write bit set (causing a read). Fault conditions are indicated by the TSD, VUV, and OCP bits in the status register (see description of OCP for conditions of use). The DIS and PNG bits do not cause an interrupt. When the master recognizes an interrupt, it addresses all slaves connected to the interrupt line in sequence, and then reads the status register to determine which device is requesting attention. The A8285/A8287 latches all conditions in the status register until the completion of the data read. Bit 0 (VSEL0), Bit 1 (VSEL1), and Bit 2 (VSEL2). These provide incremental control over the voltage on the LNB output. The available voltages provide the necessary levels for all the common standards plus the ability to add line compensation in increments of 333 mV. The voltage levels are defined in the Output Voltage Amplitude Selection table. Bit 3 (VSEL3). Switches between the low-level and highlevel output voltages on the LNB output. A value of 0 selects the low level voltage and a value of 1 selects the high level. The low-level center voltage is 12.709 V nominal, and the high level is 18.042 V nominal. These may be increased, in increments of 333 mV, by using the VSEL2, VSEL1, and VSEL0 control register bits. Bit 4 (ODT). When set to 1, enables the ODT feature (disables the A8285/A8287 if the overcurrent disable time is exceeded during an overcurrent condition on the output). When set to 0, the ODT feature is disabled. The action at the resampling point is further defined in the description for each of the status bits. The bits in the status Reading the Register After an Interrupt Start Address R Status Data SDA 0 0 0 1 0 A1 A0 1 AK SCL 1 2 3 4 5 6 7 8 9 D7 D6 D5 D4 D3 Stop D2 D1 D0 NAK IRQ Fault Event Reload Status Register www.allegromicro.com 115 Northeast Cutoff, Box 15036 Worcester, Massachusetts 01615-0036 (508) 853-5000 9 Bit 5 (ENB). When set to 1, enables the LNB output. When set to 0, the LNB output is disabled. Bit 6 (ILIM). Selects the ILIM level. When set to 0, the lower limit (typically 500 mA) is selected. When set to 1, the higher limit (typically 700 mA), is selected. Bit 7 (ENT). When set to 1, enables modulation of the LNB output with the the internal 22 kHz tone. Since the I2C interface is compatible with the 400 kHz transfer speed, this bit may be used to encode DiSEqC™ 2.0 tone bursts for communication with the LNB or switcher at the far end of the coaxial cable. Status Register (I2C Read Register). The main fault conditions: overcurrent, undervoltage, and overtemperature, are all indicated by setting the relevant bit in the Status register. In all fault cases, once the bit is set it is not reset until the A8285/A8287 is read by the I2C master. The current status of the LNB output is also indicated by DIS. DIS and PNG are the only bits that may be reset without an I2C read sequence. The normal sequence of the master in a fault condition is to detect the fault by reading the Status register, then rereading the Status register until the status bit is reset, indicating the fault condition has been reset. The fault may be detected by: continuously polling, responding to an interrupt request (IRQ), or detecting a fault condition externally and performing a diagnostic poll of all slave devices. Note that the fully operational condition of the Status register is all 0s. This simplifies checking of the status byte. Control (I2C Write) Register Table Bit Name 0 VSEL0 1 VSEL1 2 VSEL2 3 VSEL3 4 ODT 5 ENB 6 ILIM 7 ENT Function See Output Voltage Amplitude Selection Table 0: LNBx = Low range 1: LNBx = High range 0: Overcurrent disable time off 1: Overcurrent disable time on 0: Disable LNB Output 1: Enable LNB Output 0: Overcurrent Limit = 500mA 1: Overcurrent Limit = 700mA 0: Disable Tone 1: Enable 22KHz internal tone Bit 0 (TSD). A 1 indicates that the A8285/A8287 has detected an overtemperature condition and has disabled the LNB output. DIS is set and the A8285/A8287 does not re-enable the output until so instructed by writing the relevant bit into the Control register. The status of the overtemperature condition is sampled on the rising edge of the ninth clock pulse in the data read sequence. If the condition is no longer present, then the TSD bit is reset, allowing the master to re-enable the LNB output if required. If the condition is still present, then the TSD bit remains at 1. Bit 1 (OCP) Overcurrent. If the A8285/A8287 detects an overcurrent condition for greater than the detection time, and if ODT is enabled, the LNB output is then disabled. Also, the OCP bit is set to indicate that an overcurrent has occurred, and the DIS bit is set. The Status register is updated on the rising edge of the ninth clock pulse. The OCP bit is reset in all cases, allowing the master to re-enable the LNB output. If the overcurrent timer is not enabled, the A8285/A8287 operates in current limit indefinitely, and the OCP bit is not set. Bit 2 and 3. Reserved. Bit 4 (PNG) Power Not Good. Set to 1 when the LNB output is enabled and the LNB output volts are below 85% of the programmed LNB voltage. The PNG is reset when the LNB volts are within 90% of the programmed LNB voltage. Bit 5 (DIS) LNB output disabled. DIS is used to indicate the current condition of the LNB output. At power-on, or if a fault condition occurs, the disable bit is set. Having this bit change to 1 does not cause the IRQ to activate because the LNB output may be disabled intentionally by the I2C master. This bit also is reset at the end of a write sequence, if the LNB output is enabled. Bit 6. Reserved. Bit 7 (VUV) Undervoltage lockout. Set to 1 to indicate that the A8285/A8287 has detected that the input supply VIN is, or has been, below the minimum level and that an undervoltage lockout has occurred, which has disabled the LNB output. Bit 5 also is set, and the A8285/A8287 does not re-enable the output until so instructed (by having the relevant bit written into the Control register). The status of the undervoltage condition is sampled on the rising edge of the ninth clock pulse in the data read sequence. If the condition is no longer present, the VUV bit is reset, allowing the master to re-enable the LNB output if required. If the condition is still present, the VUV bit remains set to 1. www.allegromicro.com 115 Northeast Cutoff, Box 15036 Worcester, Massachusetts 01615-0036 (508) 853-5000 10 Data Sheet Preliminary 27448.003c A8285/A8287 LNB Supply and Control Voltage Regulator Power Dissipation To ensure that the device operates within the safe operating temperature range, several checks should be performed. An approximate operating junction temperature can be determined by estimating the power losses and the thermal impedance characteristics of the printed circuit board solution. To do so, perform the following procedure: 1. Estimate the maximum ambient temperature (TA). 2. Define the maximum running junction temperature (TJ)of A8285/A8287. Note that the absolute maximum junction temperature should never exceed 150ºC. 3. Determine worst case power dissipation: (a) Estimate the duty cycle D: D = 1 – [VIN / (VOUT + VD + ∆VREG)] ture and it rises by 2.7 mΩ/ºC with respect to the specified figure, RDSBOOST(25ºC), when Tj equals 25ºC. Actual RDSBOOST = RDSBOOST(25ºC) + [(Tj – 25) (d) Determine losses in each block PTOT; based on the relative value of VIN, perform either (i) or (ii): (i) When VIN < VOUT + VD + ∆VREG. Note that worst case dissipation occurs at minimum input voltage. PTOT = Pd_Rds + Pd_sw + Pd_control + Pd_lin where ×R ×D Pd_control = 15 mA × V Pd_lin = ∆V × I Pd_Rds = I2PK DSBOOST IN where: VD is the voltage drop of the boost diode, and REG (ii) When VIN > VOUT + VD + ∆VREG. Note that worst case dissipation in this case occurs at maximum input voltage. (b) Estimate the peak current in boost stage IPK: IPK = VOUT ×[ I LOAD / (0.89 ×V IN )] PTOT = Pd_control + Pd_lin where: (c) Estimate boost RDS (RDSBOOST ) at maximum running junction temperature. RDSBOOST is a function of junction tempera- Status (I2C Read) Register Table Bit Name 0 TSD Thermal Shutdown 1 OCP Overcurrent 2 Function Reserved 3 Reserved 4 PNG Power Not Good 5 DIS LNB output disabled VUV VIN Undervoltage 6 Reserved LOAD and Pd_sw (switching losses estimate); worst case = 70 mW. ∆VREG can be taken from the specification table. 7 × 2.7 mΩ] Pd_control = 15 mA ×V IN Pd_lin = (VIN – VD – VOUT ) ×I LOAD Step 4. Determine the thermal impedance required in the solution: RØJA = (TJ – TA) / PTOT The RØJA for one or two layer PCBs can be estimated from the RØJA vs. Area charts on the following page. Note: For maximum effectiveness, the PCB area underneath the IC should be filled copper and connected to pins 4 and 13 for A8285, and pins 6, 7, 18, and 19 for A8287. Where a PCB with two or more layers is used, apply thermal vias, placing them adjacent to each of the above pins, and underneath the IC. www.allegromicro.com 115 Northeast Cutoff, Box 15036 Worcester, Massachusetts 01615-0036 (508) 853-5000 11 Data Sheet Preliminary 27448.003c A8285/A8287 LNB Supply and Control Voltage Regulator Note: For the case of the A8287, the area of copper required on each layer is approximately 1.2 in2. Example. Given: VIN = 12 V Layout Considerations VOUT = 18 V Recommended placement of critical components and tracking for the A8287 is shown in the PCB Layout digagram on the following page. It is recommended that the ground plane be separated into two areas, referred to as switcher and control, on each layer using a ground plane. With respect to the input connections, VIN and 0V, the two ground plane areas are isolated as shown by the dotted line and the ground plane areas are connected together at pins 6, 7, 18, and 19. This configuration minimizes the effects of the noise produced by the switcher on the noise-sensitive sections of the circuit. ILOAD = 500 mA Two-layer PCB. Maximum ambient temperature = 70 ºC, Maximum allowed junction temperature= 110 ºC Assume: VD= 0.4 V and select ∆VREG= 0.7 V D = 1 – (12 / (18 + 0.4 + 0.7) = 0.37 × 0.5 / (0.89 × 12) = 843 mA = 0.5 + (110 – 25) × 2.7 mΩ= 730 mΩ Power-related tracking from INPUT to L1, LNB (pin 17) to L2 then OUTPUT, LX (pin 20) to D1 and L1, VBOOST (pin 23) to C4 and D1 should be as short and wide as possible. Power components such as the boost diode D1, inductor L1, and input/output capacitors C1, C9, and C4, should be located as close as possible to the IC. The DiSEqC inductor L2 should be located as far away from the boost inductor L1 to prevent potential magnetic crosstalk. IPK = 18 Worst case losses can now be estimated: Pd_Rds = 0.8432 × 0.73 × 0.37 = 192 mW Pd_sw = 70 mW Pd_control = 15 mA Pd_lin = 0.7 ×V IN = 180 mW The filter capacitor (VREG), charge pump capacitor (VCP), ac coupling tone detect capacitor (TDI), tone pull-down resistor (TOUT), and LNB output capacitor/protection diode (LNB) should be located directly next to the appropriate pin. × 0.5 = 350 mW and therefore PTOT = 0.192 + 0.07 + 0.18 + 0.35 = 0.792 W Where a PCB with two or more layers is used, it is recommended that four thermal vias be deployed as shown in the PCB Layout diagram. Note that adding additional vias does not enhance the thermal characteristics. The thermal resistance required is: (110 – 70) / 0.792 = 50.5ºC/W RØJA vs. Area Charts A8285, 16-Pin SOIC A8287, 24-Pin SOIC 80 One side Copper One side Copper Two side Copper 90 Thermal Resistance 0 Thermal Resistance Thermal Resistance (ºC /W) ( C/W) 100 80 70 60 50 (ºC /W) (0C/W) Thermal Resistance RDSBOOST Two side Copper 70 60 50 40 40 0 1 2 3 4 0 1 2 2 Area (in. Area (in ) ) 2 2 2 Area (in. Area (in )) 3 4 www.allegromicro.com 115 Northeast Cutoff, Box 15036 Worcester, Massachusetts 01615-0036 (508) 853-5000 12 Data Sheet Preliminary 27448.003c A8285/A8287 LNB Supply and Control Voltage Regulator PCB Layout Diagram VIN (INPUT) 0V Control 0V Tracking Switcher 0V 0V Plane C9 C2 Thermal Via Cut in 0V Plane C4 + C1 + C5 Note that to add additional connections, e.g. SCL, SDA, IRQ, VIN, EXTM, ADD, TDO, and TDI, some modifications to the control ground plane will be necessary. Refer to Functional Block diagram for circuit connections. C3 1 24 2 23 3 22 4 21 5 20 6 19 7 18 8 17 9 16 10 15 11 14 12 C8 D1 L1 + R1 Control 0V L2 OUTPUT C7 C6 0V D2 + 13 Control 0V Power-on Reset I2C Sequence VIN VREG IRQ SDA S T ADR R A READ Master Responds to IRQ Reads Status VUV = 1 A READ N S P S T ADR W A WRITE A S P Master Writes Enables output VUV = 0 VUV reset www.allegromicro.com 115 Northeast Cutoff, Box 15036 Worcester, Massachusetts 01615-0036 (508) 853-5000 13 Data Sheet Preliminary 27448.003c A8285/A8287 LNB Supply and Control Voltage Regulator Overtemperature and Overcurrent I2C Sequences Response to Overtemperature fault condition using multiple byte read LNB Output Disabled TJMAX TJMAX-∆TJ Overtemperature TJ LNB ouput enabled IRQ S T SDA ADR R A READ A READ A READ A READ Master Responds to IRQ Reads Status continuously TSD = 1 DIS = 1 A READ N S P S T TSD = 0 DIS = 1 ADR W A WRITE A S P Master Writes Re-enables LNB output TSD reset Response to Overcurrent fault condition using single byte read LNB output disabled VLNB ILNB LNB output enabled IRQ SDA S T ADR R A READ N S P Master Responds to IRQ Reads Status OCP = 1 DIS = 1 S T ADR W A WRITE A S P Master Writes Re-enables LNB output S T ADR R A READ N S P Master Polls Reads Status OCP = 0 DIS = 0 OCP reset www.allegromicro.com 115 Northeast Cutoff, Box 15036 Worcester, Massachusetts 01615-0036 (508) 853-5000 14 Data Sheet Preliminary 27448.003c A8285/A8287 LNB Supply and Control Voltage Regulator Terminal List Table Pin Name Pin Description A8287SLB SOIC-24 A8285SLB SOIC-16 SCL I2C Clock Input 1 1 SDA I2C Data Input/Output 2 2 IRQ Interrupt Request GND Ground VREG VIN EXTM 3 3 4,5,6,7 4 Analog Supply 8 5 Supply Input Voltage 9 6 External Modulation Input 10 7 ADD Address Select 11 8 TDO Tone Detect Out 12 - TDI Tone Detect Input 13 - NC No Connection 14 9 TCAP Capacitor for setting the rise and fall time of the LNB output 15 10 TOUT Tone Generation 16 11 LNB Output voltage to LNB GND Ground LX GND BOOST VCP Inductor drive point 17 12 18,19 13 20 14 21,22 - Tracking supply voltage to linear regulator 23 15 Gate supply voltage 24 16 Ground www.allegromicro.com 115 Northeast Cutoff, Box 15036 Worcester, Massachusetts 01615-0036 (508) 853-5000 15 Data Sheet Preliminary 27448.003c A8285/A8287 LNB Supply and Control Voltage Regulator A8285SLB 16-Pin Batwing SOIC .406 10.31 .398 10.11 8” 0” 16 .011 0.28 .009 0.23 .299 7.59 .291 7.39 .040 1.02 .020 0.51 .414 10.52 .398 10.11 1 2 .020 0.51 .014 0.36 .104 2.64 .096 2.44 .050 1.27 BSC .026 0.66 REF .012 0.30 .004 0.10 Dimensions in inches Metric dimensions (mm) in brackets, for reference only Leads 4 and 13 are connected inside the device package. A8287SLB 24-Pin Batwing SOIC .606 15.39 .598 15.19 24 8” 0” 19 18 .011 0.28 .009 0.23 .299 7.59 .291 7.39 .040 1.02 .020 0.51 .414 10.52 .398 10.11 1 .020 0.51 .014 0.36 .026 0.66 REF 2 6 7 .104 2.64 .096 2.44 .050 1.27 BSC .012 0.30 .004 0.10 Dimensions in inches Metric dimensions (mm) in brackets, for reference only Leads 6, 7, 18 and 19 are connected intside the device package. NOTES: 1. Exact body and lead configuration at vendor’s option within limits shown. 2. Lead spacing tolerance is non-cumulative. 3. Supplied in standard sticks/tubes of 49 devices or add “TR” to part number for tape and reel. www.allegromicro.com 115 Northeast Cutoff, Box 15036 Worcester, Massachusetts 01615-0036 (508) 853-5000 16 Data Sheet Preliminary 27448.003c A8285/A8287 LNB Supply and Control Voltage Regulator Purchase of I2C components of Allegro MicroSystems or one of its sublicensed Associated Companies, conveys a license under the Philips I2C Patent Rights to use these components in an I2C system, provided that the system conforms to the I2C Standard Specification as defined by Philips. DiSEqC™ is a registered trademark of Eutelsat S.A. The products described here are manufactured under one or more U.S. patents or U.S. patents pending. Allegro MicroSystems, Inc. reserves the right to make, from time to time, such departures from the detail specifications as may be required to permit improvements in the performance, reliability, or manufacturability of its products. Before placing an order, the user is cautioned to verify that the information being relied upon is current. Allegro products are not authorized for use as critical components in life-support devices or systems without express written approval. The information included herein is believed to be accurate and reliable. However, Allegro MicroSystems, Inc. assumes no responsibility for its use; nor for any infringement of patents or other rights of third parties which may result from its use. Copyright©2003 AllegroMicrosystems, Inc. www.allegromicro.com 115 Northeast Cutoff, Box 15036 Worcester, Massachusetts 01615-0036 (508) 853-5000 17 Data Sheet Preliminary 27448.003c A8285/A8287 LNB Supply and Control Voltage Regulator