TI DAC8564IDPW

DAC7565
DA
C7
565
www.ti.com ............................................................................................................................................... SBAS412A – FEBRUARY 2008 – REVISED MARCH 2008
12-Bit, Quad Channel, Ultra-Low Glitch, Voltage Output
DIGITAL-TO-ANALOG CONVERTER with 2.5V, 2ppm/°C Internal Reference
FEATURES
DESCRIPTION
1
• Relative Accuracy: 0.5LSB
• Glitch Energy: 0.15nV-s
• Internal Reference:
– 2.5V Reference Voltage (enabled by default)
– 0.004% Initial Accuracy (typ)
– 2ppm/°C Temperature Drift (typ)
– 5ppm/°C Temperature Drift (max)
– 20mA Sink/Source Capability
• Power-On Reset to Zero-Scale or Mid-Scale
• Asynchronous Clear to Zero-Scale or
Mid-Scale
• Ultra-Low Power Operation: 1mA at 5V
• Wide Power-Supply Range: +2.7V to +5.5V
• 12-Bit Monotonic Over Temperature Range
• Settling Time: 10µs to ±0.024% Full-Scale
Range (FSR)
• Low-Power Serial Interface with
Schmitt-Triggered Inputs: Up to 50MHz
• On-Chip Output Buffer Amplifier with
Rail-to-Rail Operation
• 1.8V to 5.5V Logic Compatibility
• Temperature Range: –40°C to +105°C
234
APPLICATIONS
•
•
•
•
•
•
Portable Instrumentation
Closed-Loop Servo-Control
Process Control, PLCs
Data Acquisition Systems
Programmable Attenuation
PC Peripherals
RELATED
DEVICES
The DAC7565 is a low-power, voltage-output,
four-channel, 12-bit digital-to-analog converter (DAC).
The device includes a 2.5V, 2ppm/°C internal
reference (enabled by default), giving a full-scale
output voltage range of 2.5V. The internal reference
has an initial accuracy of 0.02% and can source up to
20mA at the VREFH/VREFOUT pin. The device is
monotonic, provides very good linearity, and
minimizes undesired code-to-code transient voltages
(glitch). The DAC7565 uses a versatile 3-wire serial
interface that operates at clock rates up to 50MHz.
The interface is compatible with standard SPI™,
QSPI™, Microwire™, and digital signal processor
(DSP) interfaces.
The DAC7565 incorporates a power-on-reset circuit
that ensures the DAC output powers up at either
zero-scale or mid-scale until a valid code is written to
the device. The device contains a power-down
feature, accessed over the serial interface, that
reduces the current consumption of the device to
1.3µA at 5V. Power consumption is 2.9mW at 3V,
reducing to 1.5µW in power-down mode. The low
power consumption, internal reference, and small
footprint make this device ideal for portable,
battery-operated equipment.
The DAC7565 is drop-in and functionally compatible
with the DAC8165 and DAC8565, and functionally
compatible with the DAC7564, DAC8164 and
DAC8564. All these devices are available in a
TSSOP-16 package.
IOVDD
AVDD
VREFL
DAC7565
16-BIT
14-BIT
12-BIT
Pin and
Functionally
Compatible
DAC8565
DAC8165
DAC7565
Functionally
Compatible
DAC8564
Data Buffer A
DAC Register A
12-Bit DAC
VOUTA
Data Buffer B
DAC Register B
12-Bit DAC
VOUTB
Data Buffer C
DAC Register C
12-Bit DAC
VOUTC
Data Buffer D
DAC Register D
12-Bit DAC
VOUTD
Buffer
Control
Register
Control
SYNC
SCLK
24-Bit Shift Register
DIN
DAC8164
DAC7564
2.5V
Reference
Control Logic
GND
RST
RSTSEL
LDAC
ENABLE
Power-Down
Control Logic
VREFH/VREFOUT
1
2
3
4
Please be aware that an important notice concerning availability, standard warranty, and use in critical applications of
Texas Instruments semiconductor products and disclaimers thereto appears at the end of this data sheet.
SPI, QSPI are trademarks of Motorola, Inc.
Microwire is a trademark of National Semiconductor.
All other trademarks are the property of their respective owners.
PRODUCTION DATA information is current as of publication date.
Products conform to specifications per the terms of the Texas
Instruments standard warranty. Production processing does not
necessarily include testing of all parameters.
Copyright © 2008, Texas Instruments Incorporated
DAC7565
SBAS412A – FEBRUARY 2008 – REVISED MARCH 2008 ............................................................................................................................................... www.ti.com
This integrated circuit can be damaged by ESD. Texas Instruments recommends that all integrated circuits be handled with
appropriate precautions. Failure to observe proper handling and installation procedures can cause damage.
ESD damage can range from subtle performance degradation to complete device failure. Precision integrated circuits may be more
susceptible to damage because very small parametric changes could cause the device not to meet its published specifications.
PACKAGE/ORDERING INFORMATION (1)
PRODUCT
RELATIVE
ACCURACY
(LSB)
DIFFERENTIAL
NONLINEARITY
(LSB)
REFERENCE
DRIFT
(ppm/°C)
PACKAGELEAD
PACKAGE
DESIGNATOR
SPECIFIED
TEMPERATURE
RANGE
PACKAGE
MARKING
DAC7565A
±1
±0.5
25
TSSOP-16
PW
–40°C to +105°C
DAC7565
DAC7565C
±1
±0.5
5
TSSOP-16
PW
–40°C to +105°C
DAC7565
(1)
For the most current package and ordering information see the Package Option Addendum at the end of this document, or see the TI
web site at www.ti.com.
ABSOLUTE MAXIMUM RATINGS (1)
Over operating free-air temperature range (unless otherwise noted).
AVDD to GND
DAC7565
UNIT
–0.3 to +6
V
Digital input voltage to GND
–0.3 to +VDD + 0.3
V
VOUT to GND
–0.3 to +VDD + 0.3
V
VREF to GND
–0.3 to +VDD + 0.3
V
Operating temperature range
–40 to +125
°C
Storage temperature range
–65 to +150
°C
+150
°C
Junction temperature range (TJ max)
Power dissipation
(TJ max – TA)/θJA
W
Thermal impedance, θJA
+118
°C/W
Thermal impedance, θJC
+29
°C/W
Human body model (HBM)
4000
V
Charged device model (CDM)
1500
V
ESD rating
(1)
2
Stresses above those listed under Absolute Maximum Ratings may cause permanent damage to the device. Exposure to absolute
maximum conditions for extended periods may affect device reliability.
Submit Documentation Feedback
Copyright © 2008, Texas Instruments Incorporated
Product Folder Link(s): DAC7565
DAC7565
www.ti.com ............................................................................................................................................... SBAS412A – FEBRUARY 2008 – REVISED MARCH 2008
ELECTRICAL CHARACTERISTICS
At AVDD = 2.7V to 5.5V and –40°C to +105°C range (unless otherwise noted).
DAC7565
PARAMETER
TEST CONDITIONS
MIN
TYP
MAX
UNIT
STATIC PERFORMANCE (1)
Resolution
12
Relative accuracy
Measured by the line
passing through
codes 30 and 4050
Differential nonlinearity
12-bit monotonic
DAC7565A, DAC7565C
Offset error
Offset error drift
Gain error
Gain temperature coefficient
PSRR
Power-supply rejection ratio
±0.5
±1
LSB
±0.1
±0.5
LSB
±5
±8
mV
µV/°C
±1
Measured by the line passing through codes 30 and
4050
Full-scale error
Bits
±0.2
±0.5
% of FSR
±0.05
±0.2
% of FSR
AVDD = 5V
±1
AVDD = 2.7V
±2
ppm of
FSR/°C
1
mV/V
Output unloaded
OUTPUT CHARACTERISTICS (2)
Output voltage range
Output voltage settling time
0
To ±0.024% FSR, 0020h to 3FD0h, RL = 2kΩ,
0pF < CL < 200pF
8
RL = 2kΩ, CL = 500pF
V
10
µs
12
Slew rate
Capacitive load stability
VREF
2.2
RL = ∞
V/µs
470
pF
RL = 2kΩ
1000
Code change glitch impulse
1LSB change around major carry
0.15
nV-s
Digital feedthrough
SCLK toggling, SYNC high
0.15
nV-s
Channel-to-channel dc crosstalk
Full-scale swing on adjacent channel
0.25
LSB
Channel-to-channel ac crosstalk
1kHz full-scale sine wave, outputs unloaded
–100
dB
DC output impedance
At mid-code input
Short-circuit current
Power-up time
1
Ω
50
mA
Coming out of power-down mode, AVDD = 5V
2.5
Coming out of power-down mode, AVDD = 3V
5
µs
AC PERFORMANCE (2)
SNR
81
dB
THD
–75
dB
79
dB
SFDR
TA = +25°C, BW = 20kHz, VDD = 5V, fOUT = 1kHz.
First 19 harmonics removed for SNR calculation.
SINAD
DAC output noise density
TA = +25°C, at mid-code input, fOUT = 1kHz
DAC output noise
TA = +25°C, at mid-code input, 0.1Hz to 10Hz
74
dB
120
nV/√Hz
µVPP
6
REFERENCE
Internal reference current consumption
AVDD = 5.5V
360
µA
AVDD = 3.6V
348
µA
80
µA
External reference current
External VREF = 2.5V, if internal reference is disabled,
all four channels active
Reference input range VREFH voltage
VREFL < VREFH, AVDD – (VREFH + VREFL) /2 > 1.2V
0
AVDD
Reference input range VREFL voltage
VREFL < VREFH, AVDD – (VREFH + VREFL) /2 > 1.2V
0
AVDD/2
Reference input impedance
(1)
(2)
31
V
V
kΩ
Linearity calculated using a reduced code range of 30 to 4050; output unloaded.
Ensured by design or characterization; not production tested.
Submit Documentation Feedback
Copyright © 2008, Texas Instruments Incorporated
Product Folder Link(s): DAC7565
3
DAC7565
SBAS412A – FEBRUARY 2008 – REVISED MARCH 2008 ............................................................................................................................................... www.ti.com
ELECTRICAL CHARACTERISTICS (continued)
At AVDD = 2.7V to 5.5V and –40°C to +105°C range (unless otherwise noted).
DAC7565
PARAMETER
TEST CONDITIONS
MIN
TYP
MAX
UNIT
REFERENCE OUTPUT
Output voltage
TA = +25°C
2.4995
2.5
2.5005
V
Initial accuracy
TA = +25°C
–0.02
%
Output voltage temperature drift
Output voltage noise
±0.004
0.02
DAC7565A (3)
5
25
DAC7565C (4)
2
5
ppm/°C
µVPP
f = 0.1Hz to 10Hz
12
TA = +25°C, f = 1MHz, CL = 0µF
50
TA = +25°C, f = 1MHz, CL = 1µF
20
TA = +25°C, f = 1MHz, CL = 4µF
16
Load regulation, sourcing (5)
TA = +25°C
30
µV/mA
Load regulation, sinking (5)
TA = +25°C
15
µV/mA
Output voltage noise density
(high-frequency noise)
Output current load capability (6)
Line regulation
TA = +25°C
Long-term stability/drift (aging) (5)
TA = +25°C, time = 0 to 1900 hours
Thermal hysteresis (5)
First cycle
nV/√Hz
±20
mA
10
µV/V
50
ppm
100
Additional cycles
ppm
25
LOGIC INPUTS (6)
Input current
µA
±1
VINL
Logic input LOW voltage
VINH
Logic input HIGH voltage
2.7V ≤ IOVDD ≤ 5.5V
0.3 × IOVDD
1.8V ≤ IOVDD ≤ 2.7V
0.1 × IOVDD
2.7V ≤ IOVDD ≤ 5.5V
0.7 × IOVDD
1.8V ≤ IOVDD ≤ 2.7V
0.95 × IOVDD
V
V
Pin capacitance
3
pF
V
POWER REQUIREMENTS
AVDD
2.7
5.5
IOVDD
1.8
5.5
V
10
20
µA
AVDD = IOVDD = 3.6V to 5.5V
VINH = IOVDD and VINL = GND
1
1.6
AVDD = IOVDD = 2.7V to 3.6V
VINH = IOVDD and VINL = GND
0.95
1.5
AVDD = IOVDD = 3.6V to 5.5V
VINH = IOVDD and VINL = GND
1.3
3.5
AVDD = IOVDD = 2.7V to 3.6V
VINH = IOVDD and VINL = GND
0.5
2.5
AVDD = IOVDD = 3.6V to 5.5V
VINH = IOVDD and VINL = GND
3.6
8.8
AVDD = IOVDD = 2.7V to 3.6V
VINH = IOVDD and VINL = GND
2.6
5.4
AVDD = IOVDD = 3.6V to 5.5V
VINH = IOVDD and VINL = GND
4.7
19
AVDD = IOVDD = 2.7V to 3.6V
VINH = IOVDD and VINL = GND
1.4
9
IOIDD (6)
Normal mode
IDD (7)
All power-down modes
Normal mode
Power
Dissipation
(7)
All power-down modes
mA
µA
mW
µW
TEMPERATURE RANGE
Specified performance
(3)
(4)
(5)
(6)
(7)
4
–40
+105
°C
Reference is trimmed and tested at room temperature, and is characterized from –40°C to +120°C.
Reference is trimmed and tested at two temperatures (+25°C and +105°C), and is characterized from –40°C to +120°C.
Explained in more detail in the Application Information section of this data sheet.
Ensured by design or characterization; not production tested.
Input code = 2048, reference current included, no load.
Submit Documentation Feedback
Copyright © 2008, Texas Instruments Incorporated
Product Folder Link(s): DAC7565
DAC7565
www.ti.com ............................................................................................................................................... SBAS412A – FEBRUARY 2008 – REVISED MARCH 2008
PIN CONFIGURATIONS
PW PACKAGE
TSSOP-16
(Top View)
VOUTA
1
16 LDAC
VOUTB
2
15 ENABLE
VREFH/VREFOUT
3
14 RSTSEL
AVDD
4
13 RST
DAC7565
VREFL
5
12 IOVDD
GND
6
11 DIN
VOUTC
7
10 SCLK
VOUTD
8
9
SYNC
PIN DESCRIPTIONS
PIN
NAME
1
VOUTA
Analog output voltage from DAC A
DESCRIPTION
2
VOUTB
Analog output voltage from DAC B
3
VREFH/
VREFOUT
4
AVDD
Power-supply input, 2.7V to 5.5V
5
VREFL
Negative reference input
6
GND
Ground reference point for all circuitry on the part
7
VOUTC
Analog output voltage from DAC C
8
VOUTD
Analog output voltage from DAC D
9
SYNC
Level-triggered control input (active low). This input is the frame synchronization signal for the input data. When SYNC
goes low, it enables the input shift register, and data are sampled on subsequent falling clock edges. The DAC output
updates following the 24th clock. If SYNC is taken high before the 24th clock edge, the rising edge of SYNC acts as
an interrupt, and the write sequence is ignored by the DAC7565. Schmitt-Trigger logic input.
10
SCLK
Serial clock input. Data can be transferred at rates up to 50MHz. Schmitt-Trigger logic input.
11
DIN
12
IOVDD
13
RST
Positive reference input / reference output 2.5V if internal reference used.
Serial data input. Data are clocked into the 24-bit input shift register on each falling edge of the serial clock input.
Schmitt-Trigger logic input.
Digital input-output power supply
Asynchronous reset. Active low. If RST is low, all DAC channels reset either to zero-scale (RSTSEL = 0) or to
mid-scale (RSTSEL = 1)
14
RSTSEL
Reset select. If RSTSEL is low, input coding is binary; if high = two's complement.
15
ENABLE
The enable pin (active low) connects the SPI interface to the serial port
16
LDAC
Load DACs; rising edge triggered, loads all DAC registers
Submit Documentation Feedback
Copyright © 2008, Texas Instruments Incorporated
Product Folder Link(s): DAC7565
5
DAC7565
SBAS412A – FEBRUARY 2008 – REVISED MARCH 2008 ............................................................................................................................................... www.ti.com
6
DB0
Submit Documentation Feedback
LDAC
DIN
SYNC
SCLK
ENABLE
t8
1
t11
t4
DB23
t5
t6
t3
t1
t2
t10
24
t7
t13
t12
t14
t9
t15
DB23
SERIAL WRITE OPERATION
Copyright © 2008, Texas Instruments Incorporated
Product Folder Link(s): DAC7565
DAC7565
www.ti.com ............................................................................................................................................... SBAS412A – FEBRUARY 2008 – REVISED MARCH 2008
TIMING REQUIREMENTS (1) (2)
At AVDD = IOVDD= 2.7V to 5.5V and –40°C to +105°C range (unless otherwise noted).
DAC7565
PARAMETER
TEST CONDITIONS
t1 (3)
SCLK cycle time
t2
SCLK HIGH time
t3
SCLK LOW time
t4
SYNC to SCLK rising edge setup time
t5
Data setup time
t6
Data hold time
t7
SCLK falling edge to SYNC rising edge
t8
Minimum SYNC HIGH time
t9
24th SCLK falling edge to SYNC falling edge
t10
SYNC rising edge to 24th SCLK falling edge
(for successful SYNC interrupt)
t11
ENABLE falling edge to SYNC falling edge
t12
24th SCLK falling edge to ENABLE rising edge
t13
24th SCLK falling edge to LDAC rising edge
t14
LDAC rising edge to ENABLE rising edge
t15
LDAC HIGH time
(1)
(2)
(3)
MIN
IOVDD = AVDD = 2.7V to 3.6V
40
IOVDD = AVDD = 3.6V to 5.5V
20
IOVDD = AVDD = 2.7V to 3.6V
10
IOVDD = AVDD = 3.6V to 5.5V
20
IOVDD = AVDD = 2.7V to 3.6V
20
IOVDD = AVDD = 3.6V to 5.5V
10
IOVDD = AVDD = 2.7V to 3.6V
0
IOVDD = AVDD = 3.6V to 5.5V
0
IOVDD = AVDD = 2.7V to 3.6V
5
IOVDD = AVDD = 3.6V to 5.5V
5
IOVDD = AVDD = 2.7V to 3.6V
4.5
IOVDD = AVDD = 3.6V to 5.5V
4.5
IOVDD = AVDD = 2.7V to 3.6V
0
IOVDD = AVDD = 3.6V to 5.5V
0
IOVDD = AVDD = 2.7V to 3.6V
40
IOVDD = AVDD = 3.6V to 5.5V
20
IOVDD = AVDD = 2.7V to 3.6V
130
IOVDD = AVDD = 3.6V to 5.5V
130
IOVDD = AVDD = 2.7V to 3.6V
15
IOVDD = AVDD = 3.6V to 5.5V
15
IOVDD = AVDD = 2.7V to 3.6V
15
IOVDD = AVDD = 3.6V to 5.5V
15
IOVDD = AVDD = 2.7V to 3.6V
10
IOVDD = AVDD = 3.6V to 5.5V
10
IOVDD = AVDD = 2.7V to 3.6V
50
IOVDD = AVDD = 3.6V to 5.5V
50
IOVDD = AVDD = 2.7V to 3.6V
10
IOVDD = AVDD = 3.6V to 5.5V
10
IOVDD = AVDD = 2.7V to 3.6V
10
IOVDD = AVDD = 3.6V to 5.5V
10
TYP
MAX
UNIT
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
All input signals are specified with tR = tF = 3ns (10% to 90% of VDD) and timed from a voltage level of (VIL + VIH)/2.
See the Serial Write Operation timing diagram.
Maximum SCLK frequency is 50MHz at IOVDD = VDD = 3.6V to 5.5V and 25MHz at IOVDD = AVDD = 2.7V to 3.6V.
Submit Documentation Feedback
Copyright © 2008, Texas Instruments Incorporated
Product Folder Link(s): DAC7565
7
DAC7565
SBAS412A – FEBRUARY 2008 – REVISED MARCH 2008 ............................................................................................................................................... www.ti.com
TYPICAL CHARACTERISTICS: Internal Reference
At TA = +25°C, unless otherwise noted.
INTERNAL REFERENCE VOLTAGE
vs TEMPERATURE (Grade A)
2.503
2.503
2.502
2.502
2.501
2.501
VREF (V)
VREF (V)
INTERNAL REFERENCE VOLTAGE
vs TEMPERATURE (Grade C)
2.500
2.499
2.500
2.499
2.498
2.498
10 Units Shown
2.497
-40
-20
0
20
40
80
60
100
13 Units Shown
2.497
-40
120
-20
0
20
Temperature (°C)
40
60
80
100
120
Temperature (°C)
Figure 1.
Figure 2.
REFERENCE OUTPUT TEMPERATURE DRIFT
(–40°C to +120°C, Grade C)
REFERENCE OUTPUT TEMPERATURE DRIFT
(–40°C to +120°, Grade A)
40
30
Typ: 5ppm/°C
Max: 25ppm/°C
Typ: 2ppm/°C
Max: 5ppm/°C
Population (%)
Population (%)
30
20
20
10
10
0
0
0.5
1.0
1.5
2.0
2.5
3.0
3.5
4.0
4.5
1
5.0
5
7
9
11
13
15
Temperature Drift (ppm/°C)
Figure 3.
Figure 4.
REFERENCE OUTPUT TEMPERATURE DRIFT
(0°C to +120°C, Grade C)
LONG-TERM
STABILITY/DRIFT (1)
17
19
200
40
Typ: 1.2ppm/°C
Max: 3ppm/°C
150
100
Drift (ppm)
30
Population (%)
3
Temperature Drift (ppm/°C)
20
10
50
0
-50
Average
-100
-150
-200
0.5
(1)
8
1.0
1.5
2.0
2.5
3.0
3.5
4.0
4.5
5.0
0
300
600
900
1200
Temperature Drift (ppm/°C)
Time (Hours)
Figure 5.
Figure 6.
1500
1800
1900
20 Units Shown
0
Explained in more detail in the Application Information section of this data sheet.
Submit Documentation Feedback
Copyright © 2008, Texas Instruments Incorporated
Product Folder Link(s): DAC7565
DAC7565
www.ti.com ............................................................................................................................................... SBAS412A – FEBRUARY 2008 – REVISED MARCH 2008
TYPICAL CHARACTERISTICS: Internal Reference (continued)
At TA = +25°C, unless otherwise noted.
INTERNAL REFERENCE NOISE DENSITY
vs FREQUENCY
INTERNAL REFERENCE NOISE
0.1Hz TO 10Hz
300
250
VNOISE (5mV/div)
VN (nV/ÖHz)
12mV (peak-to-peak)
200
Reference Unbuffered
CREF = 0mF
150
100
50
CREF = 4.8mF
0
10
100
1k
10k
100k
Time (2s/div)
1M
Frequency (Hz)
Figure 7.
Figure 8.
INTERNAL REFERENCE VOLTAGE
vs LOAD CURRENT (Grade C)
INTERNAL REFERENCE VOLTAGE
vs LOAD CURRENT (Grade A)
2.505
2.505
2.504
2.504
2.503
2.503
2.502
+120°C
2.501
VREF (V)
VREF (V)
2.502
2.500
2.499
+25°C
2.498
2.501
+25°C
2.500
2.499
2.498
-40°C
2.497
+120°C
2.497
-40°C
2.496
2.496
2.495
-25
-20 -15 -10
0
-5
5
10
15
20
2.495
-25
25
-20 -15 -10
0
-5
ILOAD (mA)
5
10
15
20
25
ILOAD (mA)
Figure 9.
Figure 10.
INTERNAL REFERENCE VOLTAGE
vs SUPPLY VOLTAGE (Grade C)
INTERNAL REFERENCE VOLTAGE
vs SUPPLY VOLTAGE (Grade A)
2.503
2.503
+120°C
2.502
-40°C
+120°C
2.501
VREF (V)
VREF (V)
2.502
2.500
2.501
+25°C
2.500
+25°C
2.499
2.499
2.498
2.498
2.5
3.0
3.5
4.0
4.5
5.0
5.5
-40°C
2.5
3.0
3.5
4.0
AVDD (V)
AVDD (V)
Figure 11.
Figure 12.
4.5
5.0
Submit Documentation Feedback
Copyright © 2008, Texas Instruments Incorporated
Product Folder Link(s): DAC7565
5.5
9
DAC7565
SBAS412A – FEBRUARY 2008 – REVISED MARCH 2008 ............................................................................................................................................... www.ti.com
TYPICAL CHARACTERISTICS: DAC at AVDD = 5V
At TA = +25°C, external reference used, DAC output not loaded, and all DAC codes in straight binary data format, unless
otherwise noted.
LINEARITY ERROR AND
DIFFERENTIAL LINEARITY ERROR
vs DIGITAL INPUT CODE (–40°C)
LE (LSB)
0
-1.0
-1.0
0.3
0.2
0.1
0
-0.1
-0.2
-0.3
0.3
0.2
0.1
0
-0.1
-0.2
-0.3
1536
2048
2560
3072
3584
4096
0
2048
2560
3072
3584
Figure 14.
LINEARITY ERROR AND
DIFFERENTIAL LINEARITY ERROR
vs DIGITAL INPUT CODE (–40°C)
LINEARITY ERROR AND
DIFFERENTIAL LINEARITY ERROR
vs DIGITAL INPUT CODE (–40°C)
1.0
LE (LSB)
0
-1.0
-1.0
0.3
0.2
0.1
0
-0.1
-0.2
-0.3
0.3
0.2
0.1
0
-0.1
-0.2
-0.3
512
1024
1536
2048
2560
3072
3584
4096
0
512
1024
1536
2048
2560
3072
3584
Digital Input Code
Digital Input Code
Figure 15.
Figure 16.
LINEARITY ERROR AND
DIFFERENTIAL LINEARITY ERROR
vs DIGITAL INPUT CODE (+25°C)
LINEARITY ERROR AND
DIFFERENTIAL LINEARITY ERROR
vs DIGITAL INPUT CODE (+25°C)
1.0
Channel A, AVDD = 5V, External VREF = 4.99V
LE (LSB)
0
0
-1.0
0.3
0.2
0.1
0
-0.1
-0.2
-0.3
0.3
0.2
0.1
0
-0.1
-0.2
-0.3
DLE (LSB)
-0.5
-1.0
1024
1536
2048
2560
3072
3584
4096
4096
Channel B, AVDD = 5V, External VREF = 4.99V
0.5
-0.5
512
4096
Channel D, AVDD = 5V, External VREF = 4.99V
0.5
-0.5
0
1536
Figure 13.
0
0.5
1024
Digital Input Code
-0.5
1.0
512
Digital Input Code
Channel C, AVDD = 5V, External VREF = 4.99V
0.5
0
LE (LSB)
1024
DLE (LSB)
DLE (LSB)
LE (LSB)
1.0
DLE (LSB)
0
-0.5
512
Channel B, AVDD = 5V, External VREF = 4.99V
0.5
-0.5
0
10
1.0
Channel A, AVDD = 5V, External VREF = 4.99V
0.5
DLE (LSB)
DLE (LSB)
LE (LSB)
1.0
LINEARITY ERROR AND
DIFFERENTIAL LINEARITY ERROR
vs DIGITAL INPUT CODE (–40°C)
0
512
1024
1536
2048
2560
Digital Input Code
Digital Input Code
Figure 17.
Figure 18.
Submit Documentation Feedback
3072
3584
4096
Copyright © 2008, Texas Instruments Incorporated
Product Folder Link(s): DAC7565
DAC7565
www.ti.com ............................................................................................................................................... SBAS412A – FEBRUARY 2008 – REVISED MARCH 2008
TYPICAL CHARACTERISTICS: DAC at AVDD = 5V (continued)
At TA = +25°C, external reference used, DAC output not loaded, and all DAC codes in straight binary data format, unless
otherwise noted.
LINEARITY ERROR AND
DIFFERENTIAL LINEARITY ERROR
vs DIGITAL INPUT CODE (+25°C)
LE (LSB)
0.5
0
-0.5
-1.0
0.3
0.2
0.1
0
-0.1
-0.2
-0.3
0.3
0.2
0.1
0
-0.1
-0.2
-0.3
1024
1536
2048
2560
3072
3584
4096
0
3072
3584
LINEARITY ERROR AND
DIFFERENTIAL LINEARITY ERROR
vs DIGITAL INPUT CODE (+105°C)
1.0
LE (LSB)
0
-1.0
0.3
0.2
0.1
0
-0.1
-0.2
-0.3
0.3
0.2
0.1
0
-0.1
-0.2
-0.3
512
1024
1536
2048
2560
3072
3584
4096
0
512
1024
1536
2048
2560
3072
3584
Digital Input Code
Digital Input Code
Figure 21.
Figure 22.
LINEARITY ERROR AND
DIFFERENTIAL LINEARITY ERROR
vs DIGITAL INPUT CODE (+105°C)
LINEARITY ERROR AND
DIFFERENTIAL LINEARITY ERROR
vs DIGITAL INPUT CODE (+105°C)
1.0
Channel C, AVDD = 5V, External VREF = 4.99V
LE (LSB)
0
0
-1.0
-1.0
0.3
0.2
0.1
0
-0.1
-0.2
-0.3
0.3
0.2
0.1
0
-0.1
-0.2
-0.3
DLE (LSB)
-0.5
1024
1536
2048
2560
3072
3584
4096
4096
Channel D, AVDD = 5V, External VREF = 4.99V
0.5
-0.5
512
4096
Channel B, AVDD = 5V, External VREF = 4.99V
0.5
-0.5
0
2560
LINEARITY ERROR AND
DIFFERENTIAL LINEARITY ERROR
vs DIGITAL INPUT CODE (+105°C)
-1.0
0.5
2048
Figure 20.
-0.5
1.0
1536
Figure 19.
0
0
1024
Digital Input Code
Channel A, AVDD = 5V, External VREF = 4.99V
0.5
512
Digital Input Code
DLE (LSB)
DLE (LSB)
LE (LSB)
1.0
LE (LSB)
0
-1.0
512
Channel D, AVDD = 5V, External VREF = 4.99V
0.5
-0.5
0
DLE (LSB)
1.0
Channel C, AVDD = 5V, External VREF = 4.99V
DLE (LSB)
DLE (LSB)
LE (LSB)
1.0
LINEARITY ERROR AND
DIFFERENTIAL LINEARITY ERROR
vs DIGITAL INPUT CODE (+25°C)
0
512
1024
1536
2048
2560
Digital Input Code
Digital Input Code
Figure 23.
Figure 24.
3072
3584
Submit Documentation Feedback
Copyright © 2008, Texas Instruments Incorporated
Product Folder Link(s): DAC7565
4096
11
DAC7565
SBAS412A – FEBRUARY 2008 – REVISED MARCH 2008 ............................................................................................................................................... www.ti.com
TYPICAL CHARACTERISTICS: DAC at AVDD = 5V (continued)
At TA = +25°C, external reference used, DAC output not loaded, and all DAC codes in straight binary data format, unless
otherwise noted.
OFFSET ERROR
vs TEMPERATURE
FULL-SCALE ERROR
vs TEMPERATURE
4
0.50
AVDD = 5V
Internal VREF Enabled
Full-Scale Error (mV)
3
Offset Error (mV)
AVDD = 5V
Internal VREF Enabled
Ch C
2
1
Ch D
Ch A
0
Ch B
-1
-40
-20
0
20
40
60
80
100
Ch C
0.25
Ch D
0
-0.50
-40
120
-20
0
Temperature (°C)
40
Figure 26.
SOURCE AND SINK
CURRENT CAPABILITY
SOURCE AND SINK
CURRENT CAPABILITY
80
100
120
5.5
DAC Loaded with 0FFFh
4.5
3.5
AVDD = 5V, Ch A
Internal Reference Disabled
2.5
1.5
0.5
DAC Loaded with 0FFFh
4.5
3.5
AVDD = 5V, Ch B
Internal Reference Disabled
2.5
1.5
0.5
DAC Loaded with 0000h
DAC Loaded with 0000h
-0.5
-0.5
0
5
10
15
20
0
5
10
15
ISOURCE/SINK (mA)
ISOURCE/SINK (mA)
Figure 27.
Figure 28.
SOURCE AND SINK
CURRENT CAPABILITY
SOURCE AND SINK
CURRENT CAPABILITY
5.5
20
5.5
DAC Loaded with 0FFFh
4.5
3.5
Analog Output Voltage (V)
Analog Output Voltage (V)
60
Figure 25.
Analog Output Voltage (V)
Analog Output Voltage (V)
20
Temperature (°C)
5.5
AVDD = 5V, Ch C
Internal Reference DIsabled
2.5
1.5
0.5
DAC Loaded with 0FFFh
4.5
3.5
AVDD = 5V, Ch D
Internal Reference Disabled
2.5
1.5
0.5
DAC Loaded with 0000h
DAC Loaded with 0000h
-0.5
-0.5
0
12
Ch B
Ch A
-0.25
5
10
15
20
0
5
10
ISOURCE/SINK (mA)
ISOURCE/SINK (mA)
Figure 29.
Figure 30.
Submit Documentation Feedback
15
20
Copyright © 2008, Texas Instruments Incorporated
Product Folder Link(s): DAC7565
DAC7565
www.ti.com ............................................................................................................................................... SBAS412A – FEBRUARY 2008 – REVISED MARCH 2008
TYPICAL CHARACTERISTICS: DAC at AVDD = 5V (continued)
At TA = +25°C, external reference used, DAC output not loaded, and all DAC codes in straight binary data format, unless
otherwise noted.
POWER-SUPPLY CURRENT
vs DIGITAL INPUT CODE
1400
AVDD = 5.5V
Internal VREF Included
Power-Supply Current (mA)
Power-Supply Current (mA)
1300
POWER-SUPPLY CURRENT
vs TEMPERATURE
1200
1100
1000
900
512
1024
1536 2048 2560
Digital Input Code
3072
3584
4096
1200
1100
1000
900
0
-20
60
80
Figure 31.
Figure 32.
POWER-SUPPLY CURRENT
vs POWER-SUPPLY VOLTAGE
POWER-DOWN CURRENT
vs POWER-SUPPLY VOLTAGE
100
120
1.2
AVDD = 2.7V to 5.5V
Internal VREF Included
1090
Power-Down Current (mA)
AVDD = 2.7V to 5.5V
Internal VREF Included
DAC Loaded with 0800h
1080
1070
1060
1.0
0.8
0.6
0.4
0.2
1050
2.7
3.1
3.5
4.3
3.9
4.7
5.1
2.7
5.5
3.1
3.5
3.9
AVDD (V)
4.7
Figure 33.
Figure 34.
POWER-DOWN CURRENT
vs TEMPERATURE
POWER-SUPPLY CURRENT
vs LOGIC INPUT VOLTAGE
3200
5.1
5.5
AVDD = IOVDD = 5.5V, Internal VREF Included
AVDD = 5.5V
Power-Supply Current (mA)
2.5
2.0
1.5
1.0
0.5
0
-40
4.3
AVDD (V)
3.0
Power-Down Current (mA)
40
20
Temperature (°C)
1100
Power-Supply Current (mA)
1300
800
-40
800
0
AVDD = 5.5V
Internal VREF Included
DAC Loaded with 0800h
SYNC Input (all other digital inputs = GND)
2800
2400
Sweep from
0V to 5.5V
2000
1600
Sweep from
5.5V to 0V
1200
800
-20
0
20
40
60
80
100
120
0
1
2
3
4
5
6
VLOGIC (V)
Temperature (°C)
Figure 35.
Figure 36.
Submit Documentation Feedback
Copyright © 2008, Texas Instruments Incorporated
Product Folder Link(s): DAC7565
13
DAC7565
SBAS412A – FEBRUARY 2008 – REVISED MARCH 2008 ............................................................................................................................................... www.ti.com
TYPICAL CHARACTERISTICS: DAC at AVDD = 5V (continued)
At TA = +25°C, external reference used, DAC output not loaded, and all DAC codes in straight binary data format, unless
otherwise noted.
TOTAL HARMONIC DISTORTION
vs OUTPUT FREQUENCY
-40
TOTAL HARMONIC DISTORTION
vs OUTPUT FREQUENCY
-40
Channel A, AVDD = 5V, External VREF = 4.99V
-1dB FSR Digital Input, fS = 225kSPS
Measurement Bandwidth = 20kHz
-50
-50
-60
THD (dB)
-60
THD (dB)
Channel B, AVDD = 5V, External VREF = 4.99V
-1dB FSR Digital Input, fS = 225kSPS
Measurement Bandwidth = 20kHz
-70
THD
-80
THD
-70
-80
3rd Harmonic
3rd Harmonic
-90
-90
2nd Harmonic
2nd Harmonic
-100
-100
0
-40
1
2
3
4
5
0
2
3
4
fOUT (kHz)
Figure 37.
Figure 38.
TOTAL HARMONIC DISTORTION
vs OUTPUT FREQUENCY
TOTAL HARMONIC DISTORTION
vs OUTPUT FREQUENCY
-40
Channel C, AVDD = 5V, External VREF = 4.99V
-1dB FSR Digital Input, fS = 225kSPS
Measurement Bandwidth = 20kHz
-50
1
fOUT (kHz)
5
Channel D, AVDD = 5V, External VREF = 4.99V
-1dB FSR Digital Input, fS = 225kSPS
Measurement Bandwidth = 20kHz
-50
-60
THD (dB)
THD (dB)
-60
THD
-70
-70
THD
-80
3rd Harmonic
-80
-90
3rd Harmonic
2nd Harmonic
-90
-100
2nd Harmonic
-100
-110
0
1
2
3
4
5
0
1
2
3
fOUT (kHz)
fOUT (kHz)
Figure 39.
Figure 40.
4
5
POWER-SUPPLY CURRENT
HISTOGRAM
60
Occurrence (%)
50
AVDD = 5.5V
Internal VREF Included
40
30
20
10
0
950
1000
1050
1100
1150
1200
Power-Supply Current (mA)
Figure 41.
14
Submit Documentation Feedback
Copyright © 2008, Texas Instruments Incorporated
Product Folder Link(s): DAC7565
DAC7565
www.ti.com ............................................................................................................................................... SBAS412A – FEBRUARY 2008 – REVISED MARCH 2008
TYPICAL CHARACTERISTICS: DAC at AVDD = 5V (continued)
At TA = +25°C, external reference used, DAC output not loaded, and all DAC codes in straight binary data format, unless
otherwise noted.
SIGNAL-TO-NOISE RATIO
vs OUTPUT FREQUENCY
94
Channel C
92
Channel B
AVDD = 5V, External VREF = 4.99V
fOUT = 1kHz, fS = 225kSPS
Measurement Bandwidth = 20kHz
-20
90
Channel A
88
-40
Channel D
86
Gain (dB)
SNR (dB)
POWER SPECTRAL DENSITY
0
84
82
80
All Channels
AVDD = 5V, External VREF = 4.99V
-1dB FSR Digital Input, fS = 225kSPS
Measurement Bandwidth = 20kHz
78
76
-60
-80
-100
-120
74
-140
0
1
2
3
4
5
fOUT (kHz)
0
10
Frequency (Hz)
Figure 42.
Figure 43.
FULL-SCALE SETTLING TIME:
5V RISING EDGE
FULL-SCALE SETTLING TIME:
5V FALLING EDGE
Trigger Pulse 5V/div
AVDD = 5V
Ext VREF = 4.096V
From Code: 0000h
To Code: 0FFFh
Rising Edge
1V/div
Zoomed Rising Edge
1mV/div
5
15
20
Trigger Pulse 5V/div
AVDD = 5V
Ext VREF = 4.096V
From Code: 0FFFh
To Code: 0000h
Falling
Edge
1V/div
Time (2ms/div)
Zoomed Falling Edge
1mV/div
Time (2ms/div)
Figure 44.
Figure 45.
HALF-SCALE SETTLING TIME:
5V RISING EDGE
HALF-SCALE SETTLING TIME:
5V FALLING EDGE
Trigger Pulse 5V/div
Trigger Pulse 5V/div
AVDD = 5V
Ext VREF = 4.096V
From Code: 0C00h
To Code: 0400h
Rising
Edge
1V/div
AVDD = 5V
Ext VREF = 4.096V
From Code: 0400h
To Code: 0C00h
Zoomed Rising Edge
1mV/div
Falling
Edge
1V/div
Time (2ms/div)
Zoomed Falling Edge
1mV/div
Time (2ms/div)
Figure 46.
Figure 47.
Submit Documentation Feedback
Copyright © 2008, Texas Instruments Incorporated
Product Folder Link(s): DAC7565
15
DAC7565
SBAS412A – FEBRUARY 2008 – REVISED MARCH 2008 ............................................................................................................................................... www.ti.com
TYPICAL CHARACTERISTICS: DAC at AVDD = 5V (continued)
At TA = +25°C, external reference used, DAC output not loaded, and all DAC codes in straight binary data format, unless
otherwise noted.
GLITCH ENERGY:
5V, 1LSB STEP, FALLING EDGE
VOUT (500mV/div)
VOUT (500mV/div)
GLITCH ENERGY:
5V, 1LSB STEP, RISING EDGE
AVDD = 5V
Int VREF = 2.5V
From Code: 07FFh
To Code: 0800h
Glitch: 0.09nV-s
AVDD = 5V
Int VREF = 2.5V
From Code: 0800h
To Code: 07FFh
Glitch: 0.06nV-s
Time (5ms/div)
Figure 48.
Figure 49.
GLITCH ENERGY:
5V, 4LSB STEP, RISING EDGE
GLITCH ENERGY:
5V, 4LSB STEP, FALLING EDGE
AVDD = 5V
Int VREF = 2.5V
From Code: 0800h
To Code: 0810h
Glitch: 0.3nV-s
VOUT (1mV/div)
VOUT (1mV/div)
Time (5ms/div)
AVDD = 5V
Int VREF = 2.5V
From Code: 0810h
To Code: 0800h
Glitch: 0.2nV-s
Time (5ms/div)
Time (5ms/div)
GLITCH ENERGY:
5V, 16LSB STEP, RISING EDGE
GLITCH ENERGY:
5V, 16LSB STEP, FALLING EDGE
AVDD = 5V
Int VREF = 2.5V
From Code: 0800h
To Code: 0810h
Glitch: 0.05nV-s
VOUT (50mV/div)
Figure 51.
VOUT (50mV/div)
Figure 50.
AVDD = 5V
Int VREF = 2.5V
From Code: 0810h
To Code: 0800h
Glitch: 0.07nV-s
Time (5ms/div)
Time (5ms/div)
Figure 52.
16
Figure 53.
Submit Documentation Feedback
Copyright © 2008, Texas Instruments Incorporated
Product Folder Link(s): DAC7565
DAC7565
www.ti.com ............................................................................................................................................... SBAS412A – FEBRUARY 2008 – REVISED MARCH 2008
TYPICAL CHARACTERISTICS: DAC at AVDD = 5V (continued)
At TA = +25°C, external reference used, DAC output not loaded, and all DAC codes in straight binary data format, unless
otherwise noted.
DAC OUTPUT NOISE DENSITY
vs FREQUENCY (1)
1200
DAC OUTPUT NOISE DENSITY
vs FREQUENCY (2)
400
Internal Reference Enabled
No Load at VREFH/VREFOUT Pin
1000
DAC = Full-Scale
Internal Reference Enabled
4.8mF versus No Load at VREFH/VREFOUT Pin
350
Noise (nV/ÖHz)
Noise (nV/ÖHz)
300
800
600
Mid-Scale
400
Full Scale
250
200
No Load on Reference
150
100
Zero Scale
200
4.8mF Capacitor
On Reference
50
0
0
10
100
1k
10k
100k
1M
10
Frequency (Hz)
100
1k
10k
100k
1M
Frequency (Hz)
Figure 54.
Figure 55.
DAC OUTPUT NOISE
0.1Hz TO 10Hz
VNOISE (2mV/div)
6mV (peak-to-peak)
DAC = Mid-Scale
Internal Reference Enabled
Time (2s/div)
Figure 56.
(1)
(2)
Explained in more detail in the Application Information section of this data sheet.
See the Application Information section for more information.
Submit Documentation Feedback
Copyright © 2008, Texas Instruments Incorporated
Product Folder Link(s): DAC7565
17
DAC7565
SBAS412A – FEBRUARY 2008 – REVISED MARCH 2008 ............................................................................................................................................... www.ti.com
TYPICAL CHARACTERISTICS: DAC at AVDD = 3.6V
At TA = +25°C, internal reference used, and DAC output not loaded, all DAC codes in straight binary data format, unless
otherwise noted
POWER-SUPPLY CURRENT
vs LOGIC INPUT VOLTAGE
POWER-SUPPLY CURRENT
vs TEMPERATURE
1400
2400
Power-Supply Current (mA)
Power-Supply Current (mA)
AVDD = IOVDD = 3.6V, Internal VREF Included
SYNC Input (all other digital inputs = GND)
2000
1600
Sweep from 0V to 3.6V
1200
Sweep from
3.6V to 0V
0.5
1.0
1.5
2.0
2.5
3.0
3.5
AVDD = 3.6V
Internal VREF Included
DAC Loaded with 0800h
1200
1100
1000
900
800
-40
800
0
1300
4.0
-20
0
20
40
60
80
100
120
Temperature (°C)
VLOGIC (V)
Figure 57.
Figure 58.
POWER-SUPPLY CURRENT
HISTOGRAM
80
AVDD = 3.6V
Internal VREF Included
Occurrence (%)
60
40
20
0
900
950
1000
1050
1100
1150
1200
Power-Supply Current (mA)
Figure 59.
18
Submit Documentation Feedback
Copyright © 2008, Texas Instruments Incorporated
Product Folder Link(s): DAC7565
DAC7565
www.ti.com ............................................................................................................................................... SBAS412A – FEBRUARY 2008 – REVISED MARCH 2008
TYPICAL CHARACTERISTICS: DAC at AVDD = 2.7V
At TA = +25°C, internal reference used, and DAC output not loaded, all DAC codes in straight binary data format, unless
otherwise noted
LINEARITY ERROR AND
DIFFERENTIAL LINEARITY ERROR
vs DIGITAL INPUT CODE (–40°C)
LE (LSB)
0
-1.0
-1.0
0.3
0.2
0.1
0
-0.1
-0.2
-0.3
0.3
0.2
0.1
0
-0.1
-0.2
-0.3
1024
1536
2048
2560
3072
3584
4096
0
3072
3584
LINEARITY ERROR AND
DIFFERENTIAL LINEARITY ERROR
vs DIGITAL INPUT CODE (–40°C)
1.0
LE (LSB)
0
-1.0
0.3
0.2
0.1
0
-0.1
-0.2
-0.3
0.3
0.2
0.1
0
-0.1
-0.2
-0.3
512
1024
1536
2048
2560
3072
3584
4096
0
512
1024
1536
2048
2560
3072
3584
Digital Input Code
Digital Input Code
Figure 62.
Figure 63.
LINEARITY ERROR AND
DIFFERENTIAL LINEARITY ERROR
vs DIGITAL INPUT CODE (+25°C)
LINEARITY ERROR AND
DIFFERENTIAL LINEARITY ERROR
vs DIGITAL INPUT CODE (+25°C)
1.0
Channel A, AVDD = 2.7V, Internal VREF = 2.5V
LE (LSB)
0
0
-1.0
0.3
0.2
0.1
0
-0.1
-0.2
-0.3
0.3
0.2
0.1
0
-0.1
-0.2
-0.3
DLE (LSB)
-0.5
-1.0
1024
1536
2048
2560
3072
3584
4096
4096
Channel B, AVDD = 2.7V, Internal VREF = 2.5V
0.5
-0.5
512
4096
Channel D, AVDD = 2.7V, Internal VREF = 2.5V
0.5
-1.0
0
2560
LINEARITY ERROR AND
DIFFERENTIAL LINEARITY ERROR
vs DIGITAL INPUT CODE (–40°C)
-0.5
0.5
2048
Figure 61.
0
1.0
1536
Figure 60.
-0.5
0
1024
Digital Input Code
Channel C, AVDD = 2.7V, Internal VREF = 2.5V
0.5
512
Digital Input Code
DLE (LSB)
DLE (LSB)
LE (LSB)
1.0
LE (LSB)
0
-0.5
512
Channel B, AVDD = 2.7V, Internal VREF = 2.5V
0.5
-0.5
0
DLE (LSB)
1.0
Channel A, AVDD = 2.7V, Internal VREF = 2.5V
0.5
DLE (LSB)
DLE (LSB)
LE (LSB)
1.0
LINEARITY ERROR AND
DIFFERENTIAL LINEARITY ERROR
vs DIGITAL INPUT CODE (–40°C)
0
512
1024
1536
2048
2560
Digital Input Code
Digital Input Code
Figure 64.
Figure 65.
3072
3584
Submit Documentation Feedback
Copyright © 2008, Texas Instruments Incorporated
Product Folder Link(s): DAC7565
4096
19
DAC7565
SBAS412A – FEBRUARY 2008 – REVISED MARCH 2008 ............................................................................................................................................... www.ti.com
TYPICAL CHARACTERISTICS: DAC at AVDD = 2.7V (continued)
At TA = +25°C, internal reference used, and DAC output not loaded, all DAC codes in straight binary data format, unless
otherwise noted
LINEARITY ERROR AND
DIFFERENTIAL LINEARITY ERROR
vs DIGITAL INPUT CODE (+25°C)
LE (LSB)
0.5
0
-0.5
-1.0
0.3
0.2
0.1
0
-0.1
-0.2
-0.3
0.3
0.2
0.1
0
-0.1
-0.2
-0.3
1536
2048
2560
3072
3584
4096
0
2560
3072
3584
LINEARITY ERROR AND
DIFFERENTIAL LINEARITY ERROR
vs DIGITAL INPUT CODE (+105°C)
LINEARITY ERROR AND
DIFFERENTIAL LINEARITY ERROR
vs DIGITAL INPUT CODE (+105°C)
1.0
0
-0.5
-1.0
0.3
0.2
0.1
0
-0.1
-0.2
-0.3
0.3
0.2
0.1
0
-0.1
-0.2
-0.3
512
1024
1536
2048
2560
3072
3584
4096
0
512
1024
1536
2048
2560
3072
3584
Digital Input Code
Digital Input Code
Figure 68.
Figure 69.
LINEARITY ERROR AND
DIFFERENTIAL LINEARITY ERROR
vs DIGITAL INPUT CODE (+105°C)
LINEARITY ERROR AND
DIFFERENTIAL LINEARITY ERROR
vs DIGITAL INPUT CODE (+105°C)
1.0
Channel C, AVDD = 2.7V, Internal VREF = 2.5V
LE (LSB)
0
0
-1.0
-1.0
0.3
0.2
0.1
0
-0.1
-0.2
-0.3
0.3
0.2
0.1
0
-0.1
-0.2
-0.3
DLE (LSB)
-0.5
1024
1536
2048
2560
3072
3584
4096
4096
Channel D, AVDD = 2.7V, Internal VREF = 2.5V
0.5
-0.5
512
4096
Channel B, AVDD = 2.7V, Internal VREF = 2.5V
0.5
-1.0
0
2048
Figure 67.
-0.5
0.5
1536
Figure 66.
0
1.0
1024
Digital Input Code
LE (LSB)
0.5
512
Digital Input Code
Channel A, AVDD = 2.7V, Internal VREF = 2.5V
0
LE (LSB)
1024
DLE (LSB)
DLE (LSB)
LE (LSB)
1.0
DLE (LSB)
0
-1.0
512
Channel D, AVDD = 2.7V, Internal VREF = 2.5V
0.5
-0.5
0
20
1.0
Channel C, AVDD = 2.7V, Internal VREF = 2.5V
DLE (LSB)
DLE (LSB)
LE (LSB)
1.0
LINEARITY ERROR AND
DIFFERENTIAL LINEARITY ERROR
vs DIGITAL INPUT CODE (+25°C)
0
512
1024
1536
2048
2560
Digital Input Code
Digital Input Code
Figure 70.
Figure 71.
Submit Documentation Feedback
3072
3584
4096
Copyright © 2008, Texas Instruments Incorporated
Product Folder Link(s): DAC7565
DAC7565
www.ti.com ............................................................................................................................................... SBAS412A – FEBRUARY 2008 – REVISED MARCH 2008
TYPICAL CHARACTERISTICS: DAC at AVDD = 2.7V (continued)
At TA = +25°C, internal reference used, and DAC output not loaded, all DAC codes in straight binary data format, unless
otherwise noted
OFFSET ERROR
vs TEMPERATURE
FULL-SCALE ERROR
vs TEMPERATURE
4
0.50
AVDD = 2.7V
Internal VREF Enabled
Full-Scale Error (mV)
Ch C
3
Offset Error (mV)
AVDD = 2.7V
Internal VREF Enabled
2
1
Ch D
Ch B
0
Ch A
-1
-40
-20
0
40
20
60
80
100
Ch C
0.25
Ch D
0
-0.50
-40
120
-20
0
Temperature (°C)
20
40
Figure 72.
Figure 73.
SOURCE AND SINK
CURRENT CAPABILITY
SOURCE AND SINK
CURRENT CAPABILITY
80
100
120
3.0
DAC Loaded with 0FFFh
DAC Loaded with 0FFFh
2.5
2.0
Analog Output Voltage (V)
Analog Output Voltage (V)
60
Temperature (°C)
3.0
AVDD = 2.7V, Ch A
Internal Reference Enabled
1.5
1.0
0.5
2.5
2.0
AVDD = 2.7V, Ch B
Internal Reference Enabled
1.5
1.0
0.5
DAC Loaded with 0000h
DAC Loaded with 0000h
0
0
0
5
10
15
20
0
5
10
15
ISOURCE/SINK (mA)
ISOURCE/SINK (mA)
Figure 74.
Figure 75.
SOURCE AND SINK
CURRENT CAPABILITY
SOURCE AND SINK
CURRENT CAPABILITY
3.0
20
3.0
DAC Loaded with 0FFFh
DAC Loaded with 0FFFh
2.5
2.0
Analog Output Voltage (V)
Analog Output Voltage (V)
Ch B
Ch A
-0.25
AVDD = 2.7V, Ch C
Internal Reference Enabled
1.5
1.0
0.5
2.5
2.0
AVDD = 2.7V, Ch D
Internal Reference Enabled
1.5
1.0
0.5
DAC Loaded with 0000h
DAC Loaded with 0000h
0
0
0
5
10
15
20
0
5
10
ISOURCE/SINK (mA)
ISOURCE/SINK (mA)
Figure 76.
Figure 77.
15
Submit Documentation Feedback
Copyright © 2008, Texas Instruments Incorporated
Product Folder Link(s): DAC7565
20
21
DAC7565
SBAS412A – FEBRUARY 2008 – REVISED MARCH 2008 ............................................................................................................................................... www.ti.com
TYPICAL CHARACTERISTICS: DAC at AVDD = 2.7V (continued)
At TA = +25°C, internal reference used, and DAC output not loaded, all DAC codes in straight binary data format, unless
otherwise noted
POWER-SUPPLY CURRENT
vs DIGITAL INPUT CODE
1600
AVDD = 2.7V
Internal VREF Included
AVDD = 2.7V, Internal VREF Included
SYNC Input (all other digital inputs = GND)
Power-Supply Current (mA)
Power-Supply Current (mA)
1300
POWER-SUPPLY CURRENT
vs LOGIC INPUT VOLTAGE
1200
1100
1000
900
1400
1200
Sweep from 0V to 2.7V
Sweep from
2.7V to 0V
1000
800
800
0
512
1024
1536 2048 2560
Digital Input Code
3072
3584
4096
0
0.5
1.0
1.5
2.0
2.5
3.0
VLOGIC (V)
Figure 78.
Figure 79.
FULL-SCALE SETTLING TIME:
2.7V RISING EDGE
FULL-SCALE SETTLING TIME:
2.7V FALLING EDGE
Trigger Pulse 2.7V/div
Trigger Pulse 2.7V/div
AVDD = 2.7V
Int VREF = 2.5V
From Code: 0FFFh
To Code: 0000h
Rising
Edge
0.5V/div
AVDD = 2.7V
Int VREF = 2.5V
From Code: 0000h
To Code: 0FFFh
Zoomed Rising Edge
1mV/div
Falling
Edge
0.5V/div
Time (2ms/div)
Zoomed Falling Edge
1mV/div
Time (2ms/div)
Figure 80.
Figure 81.
HALF-SCALE SETTLING TIME:
2.7V RISING EDGE
HALF-SCALE SETTLING TIME:
2.7V FALLING EDGE
Trigger Pulse 2.7V/div
Trigger Pulse 2.7V/div
AVDD = 2.7V
Int VREF = 2.5V
From Code: 0C00h
To Code: 0400h
AVDD = 2.7V
Int VREF = 2.5V
From Code: 0400h
To Code: 0C00h
Rising
Edge
0.5V/div
Zoomed Rising Edge
1mV/div
Falling
Edge
0.5V/div
Time (2ms/div)
Time (2ms/div)
Figure 82.
22
Zoomed Falling Edge
1mV/div
Figure 83.
Submit Documentation Feedback
Copyright © 2008, Texas Instruments Incorporated
Product Folder Link(s): DAC7565
DAC7565
www.ti.com ............................................................................................................................................... SBAS412A – FEBRUARY 2008 – REVISED MARCH 2008
TYPICAL CHARACTERISTICS: DAC at AVDD = 2.7V (continued)
At TA = +25°C, internal reference used, and DAC output not loaded, all DAC codes in straight binary data format, unless
otherwise noted
AVDD = 2.7V
Int VREF = 2.5V
From Code: 07FFh
To Code: 0800h
Glitch: 0.1nV-s
GLITCH ENERGY:
2.7V, 1LSB STEP, FALLING EDGE
VOUT (500mV/div)
VOUT (500mV/div)
GLITCH ENERGY:
2.7V, 1LSB STEP, RISING EDGE
AVDD = 2.7V
Int VREF = 2.5V
From Code: 0800h
To Code: 07FFh
Glitch: 0.1nV-s
Time (5ms/div)
Time (5ms/div)
GLITCH ENERGY:
2.7V, 4LSB STEP, RISING EDGE
GLITCH ENERGY:
2.7V, 4LSB STEP, FALLING EDGE
AVDD = 2.7V
Int VREF = 2.5V
From Code: 0200h
To Code: 0204h
Glitch: 0.1nV-s
VOUT (2.5mV/div)
Figure 85.
VOUT (2.5mV/div)
Figure 84.
AVDD = 2.7V
Int VREF = 2.5V
From Code: 0204h
To Code: 0200h
Glitch: 0.1nV-s
Time (2ms/div)
Time (2ms/div)
GLITCH ENERGY:
2.7V, 16LSB STEP, RISING EDGE
GLITCH ENERGY:
2.7V, 16LSB STEP, FALLING EDGE
AVDD = 2.7V
Int VREF = 2.5V
From Code: 0800h
To Code: 0810h
Glitch: 0.11nV-s
VOUT (50mV/div)
Figure 87.
VOUT (50mV/div)
Figure 86.
AVDD = 2.7V
Int VREF = 2.5V
From Code: 0810h
To Code: 0800h
Glitch: 0.15nV-s
Time (5ms/div)
Time (5ms/div)
Figure 88.
Figure 89.
Submit Documentation Feedback
Copyright © 2008, Texas Instruments Incorporated
Product Folder Link(s): DAC7565
23
DAC7565
SBAS412A – FEBRUARY 2008 – REVISED MARCH 2008 ............................................................................................................................................... www.ti.com
TYPICAL CHARACTERISTICS: DAC at AVDD = 2.7V (continued)
At TA = +25°C, internal reference used, and DAC output not loaded, all DAC codes in straight binary data format, unless
otherwise noted
POWER-SUPPLY CURRENT
vs TEMPERATURE
POWER-DOWN CURRENT
vs TEMPERATURE
1300
2.0
AVDD = 2.7V
Internal VREF Included
DAC Loaded with 0800h
1200
1100
1000
900
800
-40
24
AVDD = 2.7V
Power-Down Current (mA)
Power-Supply Current (mA)
1400
-20
0
20
40
60
80
100
120
1.5
1.0
0.5
0
-40
-20
0
20
40
60
Temperature (°C)
Temperature (°C)
Figure 90.
Figure 91.
Submit Documentation Feedback
80
100
120
Copyright © 2008, Texas Instruments Incorporated
Product Folder Link(s): DAC7565
DAC7565
www.ti.com ............................................................................................................................................... SBAS412A – FEBRUARY 2008 – REVISED MARCH 2008
THEORY OF OPERATION
DIGITAL-TO-ANALOG CONVERTER (DAC)
The DAC7565 architecture consists of a string DAC
followed by an output buffer amplifier. Figure 92
shows a block diagram of the DAC architecture.
code loaded into the DAC register determines at
which node on the string the voltage is tapped off to
be fed into the output amplifier by closing one of the
switches connecting the string to the amplifier. It is
monotonic because it is a string of resistors.
VREF
VREFH
50kW
50kW
62kW
RDIVIDER
VOUTX
REF(+)
Resistor String
REF(-)
DAC
Register
VREF
2
R
VREFL
Figure 92. DAC7565 Architecture
To Output Amplifier
(2x Gain)
R
The input coding to the DAC7565 can be straight
binary or two's complement, so the ideal output
voltage is given by Equation 1.
DIN
VOUTX = 2 ´ VREFL + (VREFH - VREFL) ´
4096
(1)
where DIN = decimal equivalent of the binary code
that is loaded to the DAC register; it can range from 0
to 4095. X represents channel A, B, C, or D.
R
DATA FORMAT
The data format can be straight binary or two’s
complement. Table 1 illustrates the differences
between USB (unsigned straight binary) and BTC
(binary two’s complement) data formats.
R
Table 1. USB and BTC Codes
USB CODE
BTC CODE
DESCRIPTION
0FFFh
07FFh
+Full-Scale – 1LSB
0801h
0001h
Midscale + 1LSB
0800h
0000h
Midscale
07FFh
0FFFh
Midscale – 1LSB
0000h
0800h
Figure 93. Resistor String
...
...
Zero Scale
RESISTOR STRING
The resistor string section is shown in Figure 93. It is
simply a string of resistors, each of value R. The
OUTPUT AMPLIFIER
The output buffer amplifier is capable of generating
rail-to-rail voltages on its output, giving an output
range of 0V to AVDD. It is capable of driving a load of
2kΩ in parallel with 1000pF to GND. The source and
sink capabilities of the output amplifier can be seen in
the Typical Characteristics. The slew rate is 2.2V/µs,
with a full-scale settling time of 8µs with the output
unloaded.
Submit Documentation Feedback
Copyright © 2008, Texas Instruments Incorporated
Product Folder Link(s): DAC7565
25
DAC7565
SBAS412A – FEBRUARY 2008 – REVISED MARCH 2008 ............................................................................................................................................... www.ti.com
INTERNAL REFERENCE
VREF
The DAC7565 includes a 2.5V internal reference that
is enabled by default. The internal reference is
externally available at the VREFH/VREFOUT pin. A
minimum 100nF capacitor is recommended between
the reference output and GND for noise filtering.
Reference
Disable
The internal reference of the DAC7565 is a bipolar
transistor-based,
precision
bandgap
voltage
reference. Figure 94 shows the basic bandgap
topology. Transistors Q1 and Q2 are biased such that
the current density of Q1 is greater than that of Q2.
The difference of the two base-emitter voltages
(VBE1 – VBE2) has a positive temperature coefficient
and is forced across resistor R1. This voltage is
gained up and added to the base-emitter voltage of
Q2, which has a negative temperature coefficient. The
resulting output voltage is virtually independent of
temperature. The short-circuit current is limited by
design to approximately 100mA.
Enable/Disable Internal Reference
The internal reference in the DAC7565 is enabled by
default and operates in automatic mode; however, the
reference can be disabled for debugging, evaluation
purposes, or when using an external reference. A
serial command that requires a 24-bit write sequence
(see the Serial Interface section) must be used to
disable the internal reference, as shown in Table 2.
During the time that the internal reference is disabled,
the DAC functions normally using an external
reference. At this point, the internal reference is
disconnected from the VREFH/VREFOUT pin (3-state
output). Do not attempt to drive the VREFH/VREFOUT
pin externally and internally at the same time
indefinitely.
Q1
1
N
Q2
R1
R2
Figure 94. Simplified Schematic of the Bandgap
Reference
To then enable the internal reference, either perform
a power-cycle to reset the device, or write the 24-bit
serial command shown in Table 3. These actions put
the internal reference back into the default mode. In
the default mode, the internal reference powers down
automatically when all DACs power down in any of
the power-down modes (see the Power-Down Modes
section); the internal reference powers up
automatically when any DAC is powered up.
The DAC7565 also provides the option of keeping the
internal reference powered on all the time, regardless
of the DAC(s) state (powered up or down). To keep
the internal reference powered on, regardless of the
DAC(s) state, write the 24-bit serial command shown
in Table 4.
Table 2. Write Sequence for Disabling Internal Reference
(internal reference always powered down—012000h)
DB23
0
DB16
0
0
0
0
0
0
1
DB13
0
0
1
DB0
0
0
0
0
0
0
0
0
0
X
X
X
X
|————————————— Data Bits —————————————|
Table 3. Write Sequence for Enabling Internal Reference
(internal reference powered up to default mode—010000h)
DB23
0
DB16
0
0
0
0
0
0
1
DB0
0
0
0
0
0
0
0
0
0
0
0
0
X
X
X
X
|————————————— Data Bits —————————————|
Table 4. Write Sequence for Enabling Internal Reference
(internal reference always powered up—011000h)
DB23
0
DB16
0
0
0
0
0
0
1
DB12
0
0
0
1
DB0
0
0
0
0
0
0
0
0
X
X
X
X
|————————————— Data Bits —————————————|
26
Submit Documentation Feedback
Copyright © 2008, Texas Instruments Incorporated
Product Folder Link(s): DAC7565
DAC7565
www.ti.com ............................................................................................................................................... SBAS412A – FEBRUARY 2008 – REVISED MARCH 2008
SERIAL INTERFACE
The DAC7565 has a 3-wire serial interface (SYNC,
SCLK, and DIN) compatible with SPI, QSPI, and
Microwire interface standards, as well as most DSPs.
See the Serial Write Operation timing diagram for an
example of a typical write sequence.
The DAC7565 input shift register is 24 bits wide,
consisting of eight control bits (DB23 to DB16) and 12
data bits (DB15 to DB4). Bits DB0, DB1, DB2, and
DB3 are ignored by the DAC and should be treated
as don't care bits. All 24 bits of data are loaded into
the DAC under the control of the serial clock input,
SCLK. DB23 (MSB) is the first bit that is loaded into
the DAC shift register, and is followed by the rest of
the 24-bit
word
pattern, left-aligned.
This
configuration means that the first 24 bits of data are
latched into the shift register and any further clocking
of data is ignored. The DAC7565 receives all 24 bits
of data and decodes the first eight bits in order to
determine the DAC operating/control mode. The 12
bits of data that follow are decoded by the DAC to
determine the equivalent analog output, while the last
four bits (DB3, DB2, DB1, and DB0) are ignored. The
data format is straight binary with all '0's
corresponding to 0V output and all '1's corresponding
to full-scale output (that is, VREF – 1 LSB); see the
Data Format section for more details.. For all
documentation purposes, the data format and
representation used here is a true 12-bit pattern (that
is, 0FFFh for full-scale), even if the usable 12 bits of
data are extracted from a left-justified, 16-bit data
format that the DAC7565 requires.
The write sequence begins by bringing the SYNC line
low. Data from the DIN line are clocked into the 24-bit
shift register on each falling edge of SCLK. The serial
clock frequency can be as high as 50MHz, making
the DAC7565 compatible with high-speed DSPs. On
the 24th falling edge of the serial clock, the last data
bit is clocked into the shift register and the shift
register locks. Further clocking does not change the
shift register data. After 24 bits are locked into the
shift register, the eight MSBs are used as control bits
and the following 12 LSBs are used as data. After
receiving the 24th falling clock edge, the DAC7565
decodes the eight control bits and 12 data bits to
perform the required function, without waiting for a
SYNC rising edge. A new write sequence starts at the
next falling edge of SYNC. A rising edge of SYNC
before the 24-bit sequence is complete resets the SPI
interface; no data transfer occurs. After the 24th
falling edge of SCLK is received, the SYNC line may
be kept LOW or brought HIGH. In either case, the
minimum delay time from the 24th falling SCLK edge
to the next falling SYNC edge must be met in order to
properly begin the next cycle. To assure the lowest
power consumption of the device, care should be
taken that the levels are as close to each rail as
possible. Refer to the Typical Characteristics section
for Figure 36, Figure 57, and Figure 79 (Supply
Current vs Logic Input Voltage).
IOVDD AND VOLTAGE TRANSLATORS
The IOVDD pin powers the digital input structures of
the DAC7565. For single-supply operation, it can be
tied to AVDD. For dual-supply operation, the IOVDD pin
provides interface flexibility with various CMOS logic
families and should be connected to the logic supply
of the system. Analog circuits and internal logic of the
DAC7565 use AVDD as the supply voltage. The
external logic high inputs translate to AVDD by level
shifters. These level shifters use the IOVDD voltage as
a reference to shift the incoming logic HIGH levels to
AVDD. IOVDD is ensured to operate from 2.7V to 5.5V
regardless of the AVDD voltage, assuring compatibility
with various logic families. Although specified down to
2.7V, IOVDD operates at as low as 1.8V with
degraded timing and temperature performance. For
lowest power consumption, logic VIH levels should be
as close as possible to IOVDD, and logic VIL levels
should be as close as possible to GND voltages.
ASYNCHRONOUS RESET
The DAC7565 output is asynchronously set to
zero-scale voltage or mid-scale voltage (depending
on RSTSEL) immediately after the RST pin is brought
low. The RST signal resets all internal registers, and
therefore, behaves like the Power-On Reset. The
RST pin must be brought back to high before a write
sequence starts. If the RSTSEL pin is high, the RST
signal going low resets all outputs to mid-scale. If the
RSTSEL pin is low, the RST signal going low resets
all outputs to zero-scale. RSTSEL should be set at
power-up.
INPUT SHIFT REGISTER
The input shift register (SR) of the DAC7565 is 24
bits wide, as shown in Table 5, and consists of eight
control bits (DB23 to DB16), 12 data bits (DB15 to
DB4), and four don't care bits. DB23 and DB22
should always be '0'.
Table 5. Data Input Register Format
DB23
0
DB12
0
LD1
LD0
0
DAC Select 1
DAC Select 0
PD0
D11
D10
D9
D8
DB11
D7
DB0
D6
D5
D4
D3
D2
D1
D0
X
X
X
Submit Documentation Feedback
Copyright © 2008, Texas Instruments Incorporated
Product Folder Link(s): DAC7565
X
27
DAC7565
SBAS412A – FEBRUARY 2008 – REVISED MARCH 2008 ............................................................................................................................................... www.ti.com
LD1 (DB21) and LD0 (DB20) control the loading of
each analog output with the specified 12-bit data
value or power-down command. Bit DB19 must
always be '0'. The DAC channel select bits (DB18,
DB17) control the destination of the data (or
power-down command) from DAC A through DAC D.
The final control bit, PD0 (DB16), selects the
power-down mode of the DAC7565 channels as well
as the power-down mode of the internal reference.
DB21 = 0 and DB20 = 1: Single-channel update.
The data buffer and DAC register corresponding to a
DAC selected by DB18 and DB17 update with the
contents of SR data (or power-down).
The DAC7565 supports a number of different load
commands. The load commands include broadcast
commands to address all the DAC7565s on an SPI
bus. The load commands are summarized as follows:
DB21 = 1 and DB20 = 1: Broadcast update. If
DB18 = 0, then SR data are ignored and all channels
are updated with previously stored data (or
power-down). If DB18 = 1, then SR data (or
power-down) updates all channels. Refer to Table 6
for more information.
DB21 = 0 and DB20 = 0: Single-channel store. The
data buffer corresponding to a DAC selected by
DB18 and DB17 updates with the contents of SR
data (or power-down).
DB21 = 1 and DB20 = 0: Simultaneous update. A
channel selected by DB18 and DB17 updates with
the SR data; simultaneously, all the other channels
update with previously stored data (or power-down)
from data buffers.
Table 6. Control Matrix for the DAC7565
DB23
DB22
DB21
DB20
DB19
DB18
DB17
DB16
DB15
DB14
DB13-DB4
DB3-DB0
0
0
LD 1
LD 0
0
DAC Sel 1
DAC Sel 0
PD0
MSB
MSB-1
MSB-2...LSB
Don't Care
0
0
0
0
0
0
Data
X
Write to buffer A with data
0
0
0
0
1
0
Data
X
Write to buffer B with data
0
0
0
1
0
0
Data
X
Write to buffer C with data
0
0
0
1
1
0
Data
X
Write to buffer D with data
0
0
0
(00, 01, 10, or 11)
1
X
Write to buffer (selected by DB17 and DB18) with
power-down command
0
1
0
(00, 01, 10, or 11)
0
X
Write to buffer with data and load DAC (selected
by DB17 and DB18)
0
1
0
(00, 01, 10, or 11)
1
X
Write to buffer with power-down command and
load DAC (selected by DB17 and DB18)
1
0
0
(00, 01, 10, or 11)
0
X
Write to buffer with data (selected by DB17 and
DB18) and then load all DACs simultaneously
from their corresponding buffers
1
0
0
(00, 01, 10, or 11)
1
X
Write to buffer with power-down command
(selected by DB17 and DB18) and then load all
DACs simultaneously from their corresponding
buffers
See Table 7
0
Data
See Table 7
0
Data
See Table 7
0
DESCRIPTION
Broadcast Modes
0
28
X
X
1
1
0
X
X
1
1
0
X
X
1
1
0
X
X
X
X
Simultaneously update all channels of DAC7565
with data stored in each channels temporary
register
1
X
0
Data
X
Write to all channels and load all DACs with SR
data
1
X
1
X
Write to all channels and load all DACs with
power-down command in SR
See Table 7
0
Submit Documentation Feedback
Copyright © 2008, Texas Instruments Incorporated
Product Folder Link(s): DAC7565
DAC7565
www.ti.com ............................................................................................................................................... SBAS412A – FEBRUARY 2008 – REVISED MARCH 2008
SYNC INTERRUPT
LDAC FUNCTIONALITY
In a normal write sequence, the SYNC line stays low
for at least 24 falling edges of SCLK and the
addressed DAC register updates on the 24th falling
edge. However, if SYNC is brought high before the
24th falling edge, it acts as an interrupt to the write
sequence; the shift register resets and the write
sequence is discarded. Neither an update of the data
buffer contents, DAC register contents, nor a change
in the operating mode occurs (as shown in
Figure 95).
The DAC7565 offers both a software and hardware
simultaneous
update
function.
The
DAC
double-buffered architecture has been designed so
that new data can be entered for each DAC without
disturbing the analog outputs.
POWER-ON RESET TO ZERO-SCALE OR
MID-SCALE
The DAC7565 contains a power-on reset circuit that
controls the output voltage during power-up.
Depending on the RSTSEL signal, on power-up, the
DAC registers are reset and the output voltages are
set to zero-scale (RSTSEL = 0) or mid-scale
(RSTSEL = 1); they remain that way until a valid write
sequence and load command are made to the
respective DAC channel. The power-on reset is
useful in applications where it is important to know
the state of the output of each DAC while the device
is in the process of powering up.
No device pin should be brought high before power is
applied to the device. The internal reference is
powered on by default and remains that way until a
valid reference-change command is executed.
DAC7565 data updates are synchronized with the
falling edge of the 24th SCLK cycle, which follows a
falling edge of SYNC. For such synchronous updates,
the LDAC pin is not required and it must be
connected to GND permanently. The LDAC pin is
used as a positive edge triggered timing signal for
asynchronous DAC updates. To do an LDAC
operation, single-channel store(s) should be done
(loading DAC buffers) by setting LD0 and LD1 to '0'.
Multiple single-channel updates can be done in order
to set different channel buffers to desired values and
then make a rising edge on LDAC. Data buffers of all
channels must be loaded with desired data before an
LDAC rising edge. After a low-to-high LDAC
transition, all DACs are simultaneously updated with
the contents of the corresponding data buffers. If the
contents of a data buffer are not changed by the
serial interface, the corresponding DAC output
remains unchanged after the LDAC trigger.
ENABLE PIN
For normal operation, the enable pin must be driven
to a logic low. If the enable pin is driven high, the
DAC7565 stops listening to the serial port. However,
SCLK, SYNC, and DIN must not be kept floating, but
must be at some logic level. This feature can be
useful for applications that share the same serial port.
24th Falling Edge
24th Falling Edge
CLK
SYNC
DIN
DB23
DB0
DB23
Invalid/Interrupted Write Sequence:
Output/Mode Does Not Update on the 24th Falling Edge
DB0
Valid Write Sequence:
Output/Mode Updates on the 24th Falling Edge
Figure 95. SYNC Interrupt Facility
Submit Documentation Feedback
Copyright © 2008, Texas Instruments Incorporated
Product Folder Link(s): DAC7565
29
DAC7565
SBAS412A – FEBRUARY 2008 – REVISED MARCH 2008 ............................................................................................................................................... www.ti.com
POWER-DOWN MODES
The DAC7565 has two separate sets of power-down
commands. One set is for the DAC channels and the
other set is for the internal reference. For more
information on powering down the reference, see the
Enable/Disable Internal Reference section.
DAC Power-Down Commands
The DAC7565 uses four modes of operation. These
modes are accessed by setting three bits (PD2, PD1,
and PD0) in the shift register. Table 7 shows how to
control the operating mode with data bits PD0
(DB16), PD1 (DB15), and PD2 (DB14).
Table 7. DAC Operating Modes
PD0
(DB16)
PD1
(DB15)
PD2
(DB14)
0
X
X
Normal operation
1
0
1
Output typically 1kΩ to GND
1
1
0
Output typically 100kΩ to GND
1
1
1
Output high-impedance
DAC OPERATING MODES
The DAC7565 treats the power-down condition as
data; all the operational modes are still valid for
power-down. It is possible to broadcast a power-down
condition to all the DAC7565s in a system; it is also
possible to simultaneously power-down a channel
while updating data on other channels.
When the PD0 bit is set to '0', the device works
normally with its typical current consumption of 1mA
at 5.5V with an input code = 2048. The reference
current is included with the operation of all four
30
DACs. However, for the three power-down modes,
the supply current falls to 1.3µA at 5.5V (0.5µA at
3.6V). Not only does the supply current fall, but the
output stage also switches internally from the output
of the amplifier to a resistor network of known values.
The advantage of this switching is that the output
impedance of the device is known while it is in
power-down mode. As described in Table 7, there are
three different power-down options. VOUT can be
connected internally to GND through a 1kΩ resistor, a
100kΩ resistor, or open circuited (High-Z). The output
stage is shown in Figure 96. In other words, DB16,
DB15, and DB14 = '111' represent a power-down
condition with Hi-Z output impedance for a selected
channel. '101' represents a power-down condition
with 1kΩ output impedance, and '110' represents a
power-down condition with 100kΩ output impedance.
Resistor
String
DAC
Amplifier
Power-Down
Circuitry
VOUTX
Resistor
Network
Figure 96. Output Stage During Power-Down
All analog channel circuitries are shut down when the
power-down mode is exercised. However, the
contents of the DAC register are unaffected when in
power down. The time required to exit power-down is
typically 2.5µs for VDD = 5V, and 5µs for VDD = 3V.
See the Typical Characteristics for more information.
Submit Documentation Feedback
Copyright © 2008, Texas Instruments Incorporated
Product Folder Link(s): DAC7565
DAC7565
www.ti.com ............................................................................................................................................... SBAS412A – FEBRUARY 2008 – REVISED MARCH 2008
OPERATING EXAMPLES: DAC7565
For the following examples, X = don't care; value can be either '0' or '1'.
Example 1: Write to Data Buffer A Through Buffer D; Load DAC A Through DAC D Simultaneously
• 1st: Write to data buffer A:
•
•
•
DB23
DB22)
DB21
(LD1)
DB20
(LD0)
DB19
0
0
0
0
0
DB18
DB17
(DAC Sel 1) (DAC Sel 0)
0
0
DB16
(PD0)
DB15
DB14
DB13
DB12-DB4
DB3-DB0
0
D11
D10
D9
D8-D0
X
DB16
(PD0)
DB15
DB14
DB13
DB12-DB4
DB3-DB0
0
D11
D10
D9
D8-D0
X
DB16
(PD0)
DB15
DB14
DB13
DB12-DB4
DB3-DB0
0
D11
D10
D9
D8-D0
X
DB16
(PD0)
DB15
DB14
DB13
DB12-DB4
DB3-DB0
0
D11
D10
D9
D8-D0
X
2nd: Write to data buffer B:
DB23
DB22
DB21
(LD1)
DB20
(LD0)
DB19
0
0
0
0
0
DB18
DB17
(DAC Sel 1) (DAC Sel 0)
0
1
3rd: Write to data buffer C:
DB23
DB22
DB21
(LD1)
DB20
(LD0)
DB19
0
0
0
0
0
DB18
DB17
(DAC Sel 1) (DAC Sel 0)
1
0
4th: Write to data buffer D and simultaneously update all DACs:
DB23
DB22
DB21
(LD1)
DB20
(LD0)
DB19
0
0
1
0
0
DB18
DB17
(DAC Sel 1) (DAC Sel 0)
1
1
The DAC A, DAC B, DAC C, and DAC D analog outputs simultaneously settle to the specified values upon
completion of the 4th write sequence. (The DAC voltages update simultaneously after the 24th SCLK falling edge
of the fourth write cycle).
Example 2: Load New Data to DAC A Through DAC D Sequentially
• 1st: Write to data buffer A and load DAC A: DAC A output settles to specified value upon completion:
•
•
•
DB23
DB22
DB21
(LD1)
DB20
(LD0)
DB19
0
0
0
1
0
DB18
DB17
(DAC Sel 1) (DAC Sel 0)
0
0
DB16
(PD0)
DB15
DB14
DB13
DB12-DB4
DB3-DB0
0
D11
D10
D9
D8-D0
X
2nd: Write to data buffer B and load DAC B: DAC B output settles to specified value upon completion:
DB23
DB22
DB21
(LD1)
DB20
(LD0)
DB19
0
0
0
1
0
DB18
DB17
(DAC Sel 1) (DAC Sel 0)
0
1
DB16
(PD0)
DB15
DB14
DB13
DB12-DB4
DB3-DB0
0
D11
D10
D9
D8-D0
X
3rd: Write to data buffer C and load DAC C: DAC C output settles to specified value upon completion:
DB23
DB22
DB21
(LD1)
DB20
(LD0)
DB19
0
0
0
1
0
DB18
DB17
(DAC Sel 1) (DAC Sel 0)
1
0
DB16
(PD0)
DB15
DB14
DB13
DB12-DB4
DB3-DB0
0
D11
D10
D9
D8-D0
X
4th: Write to data buffer D and load DAC D: DAC D output settles to specified value upon completion:
DB23
DB22
DB21
(LD1)
DB20
(LD0)
DB19
0
0
0
1
0
DB18
DB17
(DAC Sel 1) (DAC Sel 0)
1
1
DB16
(PD0)
DB15
DB14
DB13
DB12-DB4
DB3-DB0
0
D11
D10
D9
D8-D0
X
After completion of each write cycle, DAC analog output settles to the voltage specified.
Submit Documentation Feedback
Copyright © 2008, Texas Instruments Incorporated
Product Folder Link(s): DAC7565
31
DAC7565
SBAS412A – FEBRUARY 2008 – REVISED MARCH 2008 ............................................................................................................................................... www.ti.com
Example 3: Power-Down DAC A and DAC B to 1kΩ and Power-Down DAC C and DAC D to 100kΩ
Simultaneously
• 1st: Write power-down command to data buffer A: DAC A to 1kΩ.
DB23
DB22
DB21
(LD1)
DB20
(LD0)
DB19
0
0
0
0
0
•
DB18
DB17
(DAC Sel 1) (DAC Sel 0)
0
0
DB16
(PD0)
DB15
DB14
DB13
DB12-DB4
DB3-DB0
1
0
1
X
X
X
DB16
(PD0)
DB15
DB14
DB13
DB12-DB4
DB3-DB0
1
0
1
X
X
X
DB16
(PD0)
DB15
DB14
DB13
DB12-DB4
DB3-DB0
1
1
0
X
X
X
2nd: Write power-down command to data buffer B: DAC B to 1kΩ.
DB23
DB22
DB21
(LD1)
DB20
(LD0)
DB19
0
0
0
0
0
•
DB18
DB17
(DAC Sel 1) (DAC Sel 0)
0
1
3rd: Write power-down command to data buffer C: DAC C to 100kΩ.
DB23
DB22
DB21
(LD1)
DB20
(LD0)
DB19
0
0
0
0
0
•
DB18
DB17
(DAC Sel 1) (DAC Sel 0)
1
0
4th: Write power-down command to data buffer D: DAC D to 100kΩ and simultaneously update all DACs.
DB23
DB22
DB21
(LD1)
DB20
(LD0)
DB19
0
0
1
0
0
DB18
DB17
(DAC Sel 1) (DAC Sel 0)
1
1
DB16
(PD0)
DB15
DB14
DB13
DB12-DB4
DB3-DB0
1
1
0
X
X
X
The DAC A, DAC B, DAC C, and DAC D analog outputs simultaneously power-down to each respective specified
mode upon completion of the fourth write sequence.
Example 4: Power-Down DAC A Through DAC D to High-Impedance Sequentially
• 1st: Write power-down command to data buffer A and load DAC A: DAC A output = Hi-Z:
DB23
DB22
DB21
(LD1)
DB20
(LD0)
DB19
0
0
0
1
0
•
DB18
DB17
(DAC Sel 1) (DAC Sel 0)
0
0
DB16
(PD0)
DB15
DB14
DB13
DB12-DB4
DB3-DB0
1
1
1
X
X
X
2nd: Write power-down command to data buffer B and load DAC B: DAC B output = Hi-Z:
DB23
DB22
DB21
(LD1)
DB20
(LD0)
DB19
0
0
0
1
0
•
DB18
DB17
(DAC Sel 1) (DAC Sel 0)
0
1
DB16
(PD0)
DB15
DB14
DB13
DB12-DB4
DB3-DB0
1
1
1
X
X
X
3rd: Write power-down command to data buffer C and load DAC C: DAC C output = Hi-Z:
DB23
DB22
DB21
(LD1)
DB20
(LD0)
DB19
0
0
0
1
0
•
DB18
DB17
(DAC Sel 1) (DAC Sel 0)
1
0
DB16
(PD0)
DB15
DB14
DB13
DB12-DB4
DB3-DB0
1
1
1
X
X
X
4th: Write power-down command to data buffer D and load DAC D: DAC D output = Hi-Z:
DB23
DB22
DB21
(LD1)
DB20
(LD0)
DB19
0
0
0
1
0
DB18
DB17
(DAC Sel 1) (DAC Sel 0)
1
1
DB16
(PD0)
DB15
DB14
DB13
DB12-DB4
DB3-DB0
1
1
1
X
X
X
The DAC A, DAC B, DAC C, and DAC D analog outputs sequentially power-down to high-impedance upon
completion of the first, second, third, and fourth write sequences, respectively.
32
Submit Documentation Feedback
Copyright © 2008, Texas Instruments Incorporated
Product Folder Link(s): DAC7565
DAC7565
www.ti.com ............................................................................................................................................... SBAS412A – FEBRUARY 2008 – REVISED MARCH 2008
Example 5: Power-Down All Channels Simultaneously while Reference is Always Powered Up
• 1st: Write sequence for enabling the DAC7565 internal reference all the time:
•
DB23
DB22
DB21
(LD1)
DB20
(LD0)
DB19
0
0
0
0
0
DB18
DB17
(DAC Sel 1) (DAC Sel 0)
0
DB16
(PD0)
DB15
DB14
DB13
DB12
DB11-DB4
DB3-DB0
1
0
0
0
1
X
X
0
2nd: Write sequence to power-down all DACs to high-impedance:
DB23
DB22
DB21
(LD1)
DB20
(LD0)
DB19
0
0
1
1
0
DB18
DB17
(DAC Sel 1) (DAC Sel 0)
1
DB16
(PD0)
DB15
DB14
DB13
DB12
DB11-DB4
DB3-DB0
1
1
1
X
X
X
X
0
The DAC A, DAC B, DAC C, and DAC D analog outputs sequentially power-down to high-impedance upon
completion of the first and second write sequences, respectively.
Example 6: Write a Specific Value to All DACs while Reference is Always Powered Down
• 1st: Write sequence for disabling the DAC7565 internal reference all the time (after this sequence, the
DAC7565 requires an external reference source to function):
•
DB23
DB22
DB21
(LD1)
DB20
(LD0)
DB19
0
0
0
0
0
DB18
DB17
(DAC Sel 1) (DAC Sel 0)
0
DB16
(PD0)
DB15
DB14
DB13
DB12
DB11-DB4
DB3-DB0
1
0
0
1
0
X
X
DB16
(PD0)
DB15
DB14
DB13
DB12
DB11-DB4
DB3-DB0
0
D11
D10
D9
D8
D7–D0
X
0
2nd: Write sequence to write specified data to all DACs:
DB23
DB22
DB21
(LD1)
DB20
(LD0)
DB19
0
0
1
1
0
DB18
DB17
(DAC Sel 1) (DAC Sel 0)
1
0
The DAC A, DAC B, DAC C, and DAC D analog outputs simultaneously settle to the specified values upon
completion of the fourth write sequence. (The DAC voltages update simultaneously after the 24th SCLK falling
edge of the fourth write cycle). Reference is always powered-down.
Example 7: Write a Specific Value to DAC A, while Reference is Placed in Default Mode and All Other
DACs are Powered Down to High-Impedance
• 1st: Write sequence for placing the DAC7565 internal reference into default mode. Alternately, this step can
be replaced by performing a power-on reset (see the Power-On Reset section):
•
•
DB23
DB22
DB21
(LD1)
DB20
(LD0)
DB19
0
0
0
0
0
DB18
DB17
(DAC Sel 1) (DAC Sel 0)
0
0
DB16
(PD0)
DB15
DB14
DB13
DB12
DB11-DB4
DB3-DB0
1
0
0
0
0
X
X
2nd: Write sequence to power-down all DACs to high-impedance (after this sequence, the DAC7565 internal
reference powers down automatically):
DB23
DB22
DB21
(LD1)
DB20
(LD0)
DB19
0
0
1
1
0
DB18
DB17
(DAC Sel 1) (DAC Sel 0)
1
0
DB16
(PD0)
DB15
DB14
DB13
DB12
DB11-DB4
DB3-DB0
1
1
1
X
X
X
X
3rd: Write sequence to power-up DAC A to a specified value (after this sequence, the DAC7565 internal
reference powers up automatically):
DB23
DB22
DB21
(LD1)
DB20
(LD0)
DB19
0
0
0
1
0
DB18
DB17
(DAC Sel 1) (DAC Sel 0)
0
0
DB16
(PD0)
DB15
DB14
DB13
DB12
DB11-DB4
DB3-DB0
0
D11
D10
D9
D8
D7–D0
X
The DAC B, DAC C, and DAC D analog outputs simultaneously power-down to high-impedance, and DAC A
settles to the specified value upon completion.
Submit Documentation Feedback
Copyright © 2008, Texas Instruments Incorporated
Product Folder Link(s): DAC7565
33
DAC7565
SBAS412A – FEBRUARY 2008 – REVISED MARCH 2008 ............................................................................................................................................... www.ti.com
APPLICATION INFORMATION
INTERNAL REFERENCE
The internal reference of the DAC7565 does not
require an external load capacitor for stability
because it is stable with any capacitive load.
However, for improved noise performance, an
external load capacitor of 150nF or larger connected
to the VREFH/VREFOUT output is recommended.
Figure 97 shows the typical connections required for
operation of the DAC7565 internal reference. A
supply bypass capacitor at the AVDD input is also
recommended.
DAC7565
150nF
AVDD
1
VOUTA
LDAC 16
2
VOUTB
ENABLE 15
3
VREFH/VREFOUT
RSTSEL 14
4
AVDD
5
VREFL
6
GND
7
VOUTC
SCLK 10
8
VOUTD
SYNC
RST 13
0.1mF
IOVDD 12
DIN 11
9
Temperature Drift
The internal reference is designed to exhibit minimal
drift error, defined as the change in reference output
voltage over varying temperature. The drift is
calculated using the box method described by
Equation 2:
Drift Error =
VREF_MAX - VREF_MIN
VREF ´ TRANGE
6
´ 10 (ppm/°C)
(2)
Where:
VREF_MAX = maximum reference voltage observed
within temperature range TRANGE.
VREF_MIN = minimum reference voltage observed
within temperature range TRANGE.
VREF = 2.5V, target value for reference output
voltage.
The internal reference (grade C only) features an
exceptional typical drift coefficient of 2ppm/°C from
–40°C to +120°C. Characterizing a large number of
units, a maximum drift coefficient of 5ppm/°C (grade
C only) is observed. Temperature drift results are
summarized in the Typical Characteristics.
Noise Performance
Figure 97. Typical Connections for Operating the
DAC7565 Internal Reference
Supply Voltage
The internal reference features an extremely low
dropout voltage. It can be operated with a supply of
only 5mV above the reference output voltage in an
unloaded condition. For loaded conditions, refer to
the Load Regulation section. The stability of the
internal reference with variations in supply voltage
(line regulation, dc PSRR) is also exceptional. Within
the specified supply voltage range of 2.7V to 5.5V,
the variation at VREFH/VREFOUT is less than 10µV/V;
see the Typical Characteristics.
34
Typical 0.1Hz to 10Hz voltage noise can be seen in
Figure 8, Internal Reference Noise. Additional filtering
can be used to improve output noise levels, although
care should be taken to ensure the output impedance
does not degrade the ac performance. The output
noise spectrum at VREFH/VREFOUT without any
external components is depicted in Figure 7, Internal
Reference Noise Density vs Frequency. Another
noise density spectrum is also shown in Figure 7.
This spectrum was obtained using a 4.8µF load
capacitor at VREFH/VREFOUT for noise filtering.
Internal reference noise impacts the DAC output
noise; see the DAC Noise Performance section for
more details.
Submit Documentation Feedback
Copyright © 2008, Texas Instruments Incorporated
Product Folder Link(s): DAC7565
DAC7565
www.ti.com ............................................................................................................................................... SBAS412A – FEBRUARY 2008 – REVISED MARCH 2008
Load Regulation
Thermal Hysteresis
Load regulation is defined as the change in reference
output voltage as a result of changes in load current.
The load regulation of the internal reference is
measured using force and sense contacts as shown
in Figure 98. The force and sense lines reduce the
impact of contact and trace resistance, resulting in
accurate measurement of the load regulation
contributed solely by the internal reference.
Measurement results are summarized in the Typical
Characteristics. Force and sense lines should be
used for applications that require improved load
regulation.
Thermal hysteresis for a reference is defined as the
change in output voltage after operating the device at
+25°C, cycling the device through the operating
temperature range, and returning to +25°C.
Hysteresis is expressed by Equation 3:
Output Pin
Contact and
Trace Resistance
VOUT
Force Line
IL
|VREF_PRE - VREF_POST|
VREF_NOM
6
´ 10 (ppm/°C)
(3)
Where:
VHYST = thermal hysteresis.
VREF_PRE = output voltage measured at +25°C
pre-temperature cycling.
VREF_POST = output voltage measured after the
device cycles through the temperature range of
–40°C to +120°C, and returns to +25°C.
DAC NOISE PERFORMANCE
Sense Line
Meter
VHYST =
Load
Figure 98. Accurate Load Regulation of the
DAC7565 Internal Reference
Long-Term Stability
Long-term stability/aging refers to the change of the
output voltage of a reference over a period of months
or years. This effect lessens as time progresses (see
Figure 6, the typical long-term stability curve). The
typical drift value for the internal reference is 50ppm
from 0 hours to 1900 hours. This parameter is
characterized by powering-up and measuring 20 units
at regular intervals for a period of 1900 hours.
Typical noise performance for the DAC7565 with the
internal reference enabled is shown in Figure 54 to
Figure 56. Output noise spectral density at the VOUT
pin versus frequency is depicted in Figure 54 for
full-scale, midscale, and zero-scale input codes. The
typical noise density for midscale code is 120nV/√Hz
at 1kHz and 100nV/√Hz at 1MHz. High-frequency
noise can be improved by filtering the reference noise
as shown in Figure 55, where a 4.8µF load capacitor
is connected to the VREFH/VREFOUT pin and
compared to the no-load condition. Integrated output
noise between 0.1Hz and 10Hz is close to 6µVPP
(midscale), as shown in Figure 56.
Submit Documentation Feedback
Copyright © 2008, Texas Instruments Incorporated
Product Folder Link(s): DAC7565
35
DAC7565
SBAS412A – FEBRUARY 2008 – REVISED MARCH 2008 ............................................................................................................................................... www.ti.com
BIPOLAR OPERATION USING THE DAC7565
The DAC7565 is designed for single-supply
operation, but a bipolar output range is also possible
using the circuit in either Figure 99 or Figure 100.
The circuit shown gives an output voltage range of
±VREF. Rail-to-rail operation at the amplifier output is
achievable using an OPA703 as the output amplifier.
The output voltage for any input code can be
calculated with Equation 4:
VO =
VREF ´
D
4096
R 1 + R2
´
R1
- VREF ´
V
H
R2
10kW
AV
REF
DD
+6V
R1
10kW
OPA703
AVDD
±5V
VOUT
VREFH DAC7565
10mF
0.1mF
VREFL
-6V
GND
R2
3-Wire
Serial Interface
R1
(4)
where D represents the input code in decimal
(0–4095).
Figure 99. Bipolar Output Range Using External
Reference at 5V
With VREFH = 5V, R1 = R2 = 10kΩ.
R2
10kW
AV
DD
VO =
10 ´ D
4096
- 5V
This result has an output voltage range of ±5V with
0000h corresponding to a –5V output and 0FFFh
corresponding to a +5V output, as shown in
Figure 99. Similarly, using the internal reference, a
±2.5V output voltage range can be achieved, as
Figure 100 shows.
+6V
R1
10kW
(5)
OPA703
AVDD
±2.5V
VOUT
VREFH DAC7565
150nF
VREFL
GND
-6V
3-Wire
Serial Interface
Figure 100. Bipolar Output Range Using Internal
Reference
36
Submit Documentation Feedback
Copyright © 2008, Texas Instruments Incorporated
Product Folder Link(s): DAC7565
DAC7565
www.ti.com ............................................................................................................................................... SBAS412A – FEBRUARY 2008 – REVISED MARCH 2008
MICROPROCESSOR INTERFACING
Microwireä
DAC7565
DAC7565 to an 8051 Interface
CS
SYNC
Figure 101 shows a serial interface between the
DAC7565 and a typical 8051-type microcontroller.
The setup for the interface is as follows: TXD of the
8051 drives SCLK of the DAC7565, while RXD drives
the serial data line of the device. The SYNC signal is
derived from a bit-programmable pin on the port of
the 8051; in this case, port line P3.3 is used. When
data are to be transmitted to the DAC7565, P3.3 is
taken low. The 8051 transmits data in 8-bit bytes;
thus, only eight falling clock edges occur in the
transmit cycle. To load data to the DAC, P3.3 is left
low after the first eight bits are transmitted; then, a
second write cycle is initiated to transmit the second
byte of data. P3.3 is taken high following the
completion of the third write cycle. The 8051 outputs
the serial data in a format that has the LSB first. The
DAC7565 requires its data with the MSB as the first
bit received. The 8051 transmit routine must therefore
take this requirement into account, and mirror the
data as needed.
SK
SCLK
SO
DIN
NOTE: (1) Additional pins omitted for clarity.
Figure 102. DAC7565 to Microwire Interface
DAC7565 to 68HC11 Interface
Figure 103 shows a serial interface between the
DAC7565 and the 68HC11 microcontroller. SCK of
the 68HC11 drives the SCLK of the DAC7565, while
the MOSI output drives the serial data line of the
DAC. The SYNC signal derives from a port line
(PC7), similar to the 8051 diagram.
68HC11(1)
DAC7565(1)
PC7
SYNC
SCK
SCLK
MOSI
80C51/80L51(1)
(1)
DIN
DAC7565(1)
NOTE: (1) Additional pins omitted for clarity.
P3.3
SYNC
TXD
SCLK
RXD
DIN
NOTE: (1) Additional pins omitted for clarity.
Figure 101. DAC7565 to 80C51/80L51 Interface
DAC7565 to Microwire Interface
Figure 102 shows an interface between the DAC7565
and any Microwire-compatible device. Serial data are
shifted out on the falling edge of the serial clock and
are clocked into the DAC7565 on the rising edge of
the SK signal.
Figure 103. DAC7565 to 68HC11 Interface
The 68HC11 should be configured so that its CPOL
bit is '0' and its CPHA bit is '1'. This configuration
causes data appearing on the MOSI output to be
valid on the falling edge of SCK. When data are
being transmitted to the DAC, the SYNC line is held
low (PC7). Serial data from the 68HC11 are
transmitted in 8-bit bytes with only eight falling clock
edges occurring in the transmit cycle. (Data are
transmitted MSB first.) In order to load data to the
DAC7565, PC7 is left low after the first eight bits are
transferred; then, a second and third serial write
operation are performed to the DAC. PC7 is taken
high at the end of this procedure.
Submit Documentation Feedback
Copyright © 2008, Texas Instruments Incorporated
Product Folder Link(s): DAC7565
37
DAC7565
SBAS412A – FEBRUARY 2008 – REVISED MARCH 2008 ............................................................................................................................................... www.ti.com
LAYOUT
A precision analog component requires careful layout,
adequate bypassing, and clean, well-regulated power
supplies.
The DAC7565 offers single-supply operation, and is
often used in close proximity with digital logic,
microcontrollers, microprocessors, and digital signal
processors. The more digital logic present in the
design and the higher the switching speed, the more
difficult it is to keep digital noise from appearing at
the output.
As a result of the single ground pin of the DAC7565,
all return currents (including digital and analog return
currents for the DAC) must flow through a single
point. Ideally, GND would be connected directly to an
analog ground plane. This plane would be separate
from the ground connection for the digital
components until they were connected at the
power-entry point of the system.
38
The power applied to VDD should be well-regulated
and low noise. Switching power supplies and dc/dc
converters often have high-frequency glitches or
spikes riding on the output voltage. In addition, digital
components can create similar high-frequency spikes
as their internal logic switches states. This noise can
easily couple into the DAC output voltage through
various paths between the power connections and
analog output.
As with the GND connection, VDD should be
connected to a power-supply plane or trace that is
separate from the connection for digital logic until
they are connected at the power-entry point. In
addition, a 1µF to 10µF capacitor and 0.1µF bypass
capacitor are strongly recommended. In some
situations, additional bypassing may be required,
such as a 100µF electrolytic capacitor or even a Pi
filter made up of inductors and capacitors—all
designed to essentially low-pass filter the supply and
remove the high-frequency noise.
Submit Documentation Feedback
Copyright © 2008, Texas Instruments Incorporated
Product Folder Link(s): DAC7565
DAC7565
www.ti.com ............................................................................................................................................... SBAS412A – FEBRUARY 2008 – REVISED MARCH 2008
PARAMETER DEFINITIONS
With the increased complexity of many different
specifications listed in product data sheets, this
section summarizes selected specifications related to
digital-to-analog converters.
STATIC PERFORMANCE
Static performance parameters are specifications
such as differential nonlinearity (DNL) or integral
nonlinearity (INL). These are dc specifications and
provide information on the accuracy of the DAC. They
are most important in applications where the signal
changes slowly and accuracy is required.
Resolution
Generally, the DAC resolution can be expressed in
different forms. Specifications such as IEC 60748-4
recognize the numerical, analog, and relative
resolution. The numerical resolution is defined as the
number of digits in the chosen numbering system
necessary to express the total number of steps of the
transfer characteristic, where a step represents both
a digital input code and the corresponding discrete
analogue output value. The most commonly-used
definition of resolution provided in data sheets is the
numerical resolution expressed in bits.
Full-Scale Error
Full-scale error is defined as the deviation of the real
full-scale output voltage from the ideal output voltage
while the DAC register is loaded with the full-scale
code. Ideally, the output should be VDD – 1 LSB. The
full-scale error is expressed in percent of full-scale
range (%FSR).
Offset Error
The offset error is defined as the difference between
actual output voltage and the ideal output voltage in
the linear region of the transfer function. This
difference is calculated by using a straight line
defined by two codes. Since the offset error is defined
by a straight line, it can have a negative or positve
value. Offset error is measured in mV.
Zero-Code Error
The zero-code error is defined as the DAC output
voltage, when all '0's are loaded into the DAC
register. Zero-scale error is a measure of the
difference between actual output voltage and ideal
output voltage (0V). It is expressed in mV. It is
primarily caused by offsets in the output amplifier.
Least Significant Bit (LSB)
Gain Error
The least significant bit (LSB) is defined as the
smallest value in a binary coded system. The value of
the LSB can be calculated by dividing the full-scale
output voltage by 2n, where n is the resolution of the
converter.
Gain error is defined as the deviation in the slope of
the real DAC transfer characteristic from the ideal
transfer function. Gain error is expressed as a
percentage of full-scale range (%FSR).
Most Significant Bit (MSB)
Full-scale error drift is defined as the change in
full-scale error with a change in temperature.
Full-scale error drift is expressed in units of
%FSR/°C.
The most significant bit (MSB) is defined as the
largest value in a binary coded system. The value of
the MSB can be calculated by dividing the full-scale
output voltage by 2. Its value is one-half of full-scale.
Relative Accuracy or Integral Nonlinearity (INL)
Relative accuracy or integral nonlinearity (INL) is
defined as the maximum deviation between the real
transfer function and a straight line passing through
the endpoints of the ideal DAC transfer function. DNL
is measured in LSBs.
Differential Nonlinearity (DNL)
Differential nonlinearity (DNL) is defined as the
maximum deviation of the real LSB step from the
ideal 1LSB step. Ideally, any two adjacent digital
codes correspond to output analog voltages that are
exactly one LSB apart. If the DNL is less than 1LSB,
the DAC is said to be monotonic.
Full-Scale Error Drift
Offset Error Drift
Offset error drift is defined as the change in offset
error with a change in temperature. Offset error drift
is expressed in µV/°C.
Zero-Code Error Drift
Zero-code error drift is defined as the change in
zero-code error with a change in temperature.
Zero-code error drift is expressed in µV/°C.
Gain Temperature Coefficient
The gain temperature coefficient is defined as the
change in gain error with changes in temperature.
The gain temperature coefficient is expressed in ppm
of FSR/°C.
Submit Documentation Feedback
Copyright © 2008, Texas Instruments Incorporated
Product Folder Link(s): DAC7565
39
DAC7565
SBAS412A – FEBRUARY 2008 – REVISED MARCH 2008 ............................................................................................................................................... www.ti.com
Power-Supply Rejection Ratio (PSRR)
Channel-to-Channel DC Crosstalk
Power-supply rejection ratio (PSRR) is defined as the
ratio of change in output voltage to a change in
supply voltage for a full-scale output of the DAC. The
PSRR of a device indicates how the output of the
DAC is affected by changes in the supply voltage.
PSRR is measured in decibels (dB).
Channel-to-channel dc crosstalk is defined as the dc
change in the output level of one DAC channel in
response to a change in the output of another DAC
channel. It is measured with a full-scale output
change on one DAC channel, while monitoring
another DAC channel remains at midscale; it is
expressed in LSB.
Monotonicity
Monotonicity is defined as a slope whose sign does
not change. If a DAC is monotonic, the output
changes in the same direction or remains at least
constant for each step increase (or decrease) in the
input code.
DYNAMIC PERFORMANCE
Dynamic performance parameters are specifications
such as settling time or slew rate, which are important
in applications where the signal rapidly changes
and/or high frequency signals are present.
Slew Rate
The output slew rate (SR) of an amplifier or other
electronic circuit is defined as the maximum rate of
change of the output voltage for all possible input
signals.
SR = max
Channel-to-Channel AC Crosstalk
AC crosstalk in a multi-channel DAC is defined as the
amount of ac interference experienced on the output
of a channel at a frequency (f) (and its harmonics),
when the output of an adjacent channel changes its
value at the rate of frequency (f). It is measured with
one channel output oscillating with a sine wave of
1kHz frequency while monitoring the amplitude of
1kHz harmonics on an adjacent DAC channel output
(kept at zero scale); it is expressed in dB.
Signal-to-Noise Ratio (SNR)
Signal-to-noise ratio (SNR) is defined as the ratio of
the root mean-squared (RMS) value of the output
signal divided by the RMS values of the sum of all
other spectral components below one-half the output
frequency, not including harmonics or dc. SNR is
measured in dB.
DVOUT(t)
Total Harmonic Distortion (THD)
Dt
Where ΔVOUT(t) is the output produced by the
amplifier as a function of time t.
Output Voltage Settling Time
Settling time is the total time (including slew time) for
the DAC output to settle within an error band around
its final value after a change in input. Settling times
are specified to within ±0.003% (or whatever value is
specified) of full-scale range (FSR).
Total harmonic distortion + noise is defined as the
ratio of the RMS values of the harmonics and noise
to the value of the fundamental frequency. It is
expressed in a percentage of the fundamental
frequency amplitude at sampling rate fS.
Spurious-Free Dynamic Range (SFDR)
Digital-to-analog glitch impulse is the impulse injected
into the analog output when the input code in the
DAC register changes state. It is normally specified
as the area of the glitch in nanovolts-second (nV-s),
and is measured when the digital input code changes
by 1LSB at the major carry transition.
Spurious-free dynamic range (SFDR) is the usable
dynamic range of a DAC before spurious noise
interferes or distorts the fundamental signal. SFDR is
the measure of the difference in amplitude between
the fundamental and the largest harmonically or
non-harmonically related spur from dc to the full
Nyquist bandwidth (half the DAC sampling rate, or
fS/2). A spur is any frequency bin on a spectrum
analyzer, or from a Fourier transform, of the analog
output of the DAC. SFDR is specified in decibels
relative to the carrier (dBc).
Digital Feedthrough
Signal-to-Noise plus Distortion (SINAD)
Digital feedthrough is defined as impulse seen at the
output of the DAC from the digital inputs of the DAC.
It is measured when the DAC output is not updated. It
is specified in nV-s, and measured with a full-scale
code change on the data bus; that is, from all '0's to
all '1's and vice versa.
SINAD includes all the harmonic and outstanding
spurious components in the definition of output noise
power in addition to quantizing any internal random
noise power. SINAD is expressed in dB at a specified
input frequency and sampling rate, fS.
Code Change/Digital-to-Analog Glitch Energy
40
Submit Documentation Feedback
Copyright © 2008, Texas Instruments Incorporated
Product Folder Link(s): DAC7565
DAC7565
www.ti.com ............................................................................................................................................... SBAS412A – FEBRUARY 2008 – REVISED MARCH 2008
DAC Output Noise Density
Full-Scale Range (FSR)
Output
noise
density
is
defined
as
internally-generated random noise. Random noise is
characterized as a spectral density (nV/√Hz). It is
measured by loading the DAC to midscale and
measuring noise at the output.
Full-scale range (FSR) is the difference between the
maximum and minimum analog output values that the
DAC is specified to provide; typically, the maximum
and minimum values are also specified. For an n-bit
DAC, these values are usually given as the values
matching with code 0 and 2n.
DAC Output Noise
DAC output noise is defined as any voltage deviation
of DAC output from the desired value (within a
particular frequency band). It is measured with a DAC
channel kept at midscale while filtering the output
voltage within a band of 0.1Hz to 10Hz and
measuring its amplitude peaks. It is expressed in
terms of peak-to-peak voltage (Vpp).
Submit Documentation Feedback
Copyright © 2008, Texas Instruments Incorporated
Product Folder Link(s): DAC7565
41
PACKAGE OPTION ADDENDUM
www.ti.com
20-Mar-2008
PACKAGING INFORMATION
Orderable Device
Status (1)
Package
Type
Package
Drawing
Pins Package Eco Plan (2)
Qty
DAC7565IAPW
ACTIVE
TSSOP
PW
16
90
Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-2-260C-1 YEAR
DAC7565IAPWG4
ACTIVE
TSSOP
PW
16
90
Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-2-260C-1 YEAR
DAC7565IAPWR
ACTIVE
TSSOP
PW
16
2000 Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-2-260C-1 YEAR
DAC7565IAPWRG4
ACTIVE
TSSOP
PW
16
2000 Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-2-260C-1 YEAR
DAC7565ICPW
ACTIVE
TSSOP
PW
16
90
Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-2-260C-1 YEAR
DAC7565ICPWG4
ACTIVE
TSSOP
PW
16
90
Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-2-260C-1 YEAR
DAC7565ICPWR
ACTIVE
TSSOP
PW
16
2000 Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-2-260C-1 YEAR
DAC7565ICPWRG4
ACTIVE
TSSOP
PW
16
2000 Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-2-260C-1 YEAR
Lead/Ball Finish
MSL Peak Temp (3)
(1)
The marketing status values are defined as follows:
ACTIVE: Product device recommended for new designs.
LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect.
NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in
a new design.
PREVIEW: Device has been announced but is not in production. Samples may or may not be available.
OBSOLETE: TI has discontinued the production of the device.
(2)
Eco Plan - The planned eco-friendly classification: Pb-Free (RoHS), Pb-Free (RoHS Exempt), or Green (RoHS & no Sb/Br) - please check
http://www.ti.com/productcontent for the latest availability information and additional product content details.
TBD: The Pb-Free/Green conversion plan has not been defined.
Pb-Free (RoHS): TI's terms "Lead-Free" or "Pb-Free" mean semiconductor products that are compatible with the current RoHS requirements
for all 6 substances, including the requirement that lead not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered
at high temperatures, TI Pb-Free products are suitable for use in specified lead-free processes.
Pb-Free (RoHS Exempt): This component has a RoHS exemption for either 1) lead-based flip-chip solder bumps used between the die and
package, or 2) lead-based die adhesive used between the die and leadframe. The component is otherwise considered Pb-Free (RoHS
compatible) as defined above.
Green (RoHS & no Sb/Br): TI defines "Green" to mean Pb-Free (RoHS compatible), and free of Bromine (Br) and Antimony (Sb) based flame
retardants (Br or Sb do not exceed 0.1% by weight in homogeneous material)
(3)
MSL, Peak Temp. -- The Moisture Sensitivity Level rating according to the JEDEC industry standard classifications, and peak solder
temperature.
Important Information and Disclaimer:The information provided on this page represents TI's knowledge and belief as of the date that it is
provided. TI bases its knowledge and belief on information provided by third parties, and makes no representation or warranty as to the
accuracy of such information. Efforts are underway to better integrate information from third parties. TI has taken and continues to take
reasonable steps to provide representative and accurate information but may not have conducted destructive testing or chemical analysis on
incoming materials and chemicals. TI and TI suppliers consider certain information to be proprietary, and thus CAS numbers and other limited
information may not be available for release.
In no event shall TI's liability arising out of such information exceed the total purchase price of the TI part(s) at issue in this document sold by TI
to Customer on an annual basis.
Addendum-Page 1
PACKAGE MATERIALS INFORMATION
www.ti.com
15-Mar-2008
TAPE AND REEL INFORMATION
*All dimensions are nominal
Device
Package Package Pins
Type Drawing
SPQ
Reel
Reel
Diameter Width
(mm) W1 (mm)
A0 (mm)
B0 (mm)
K0 (mm)
P1
(mm)
W
Pin1
(mm) Quadrant
DAC7565IAPWR
TSSOP
PW
16
2000
330.0
12.4
6.67
5.4
1.6
8.0
12.0
Q1
DAC7565ICPWR
TSSOP
PW
16
2000
330.0
12.4
6.67
5.4
1.6
8.0
12.0
Q1
Pack Materials-Page 1
PACKAGE MATERIALS INFORMATION
www.ti.com
15-Mar-2008
*All dimensions are nominal
Device
Package Type
Package Drawing
Pins
SPQ
Length (mm)
Width (mm)
Height (mm)
DAC7565IAPWR
TSSOP
PW
16
2000
346.0
346.0
29.0
DAC7565ICPWR
TSSOP
PW
16
2000
346.0
346.0
29.0
Pack Materials-Page 2
MECHANICAL DATA
MTSS001C – JANUARY 1995 – REVISED FEBRUARY 1999
PW (R-PDSO-G**)
PLASTIC SMALL-OUTLINE PACKAGE
14 PINS SHOWN
0,30
0,19
0,65
14
0,10 M
8
0,15 NOM
4,50
4,30
6,60
6,20
Gage Plane
0,25
1
7
0°– 8°
A
0,75
0,50
Seating Plane
0,15
0,05
1,20 MAX
PINS **
0,10
8
14
16
20
24
28
A MAX
3,10
5,10
5,10
6,60
7,90
9,80
A MIN
2,90
4,90
4,90
6,40
7,70
9,60
DIM
4040064/F 01/97
NOTES: A.
B.
C.
D.
All linear dimensions are in millimeters.
This drawing is subject to change without notice.
Body dimensions do not include mold flash or protrusion not to exceed 0,15.
Falls within JEDEC MO-153
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
IMPORTANT NOTICE
Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, modifications, enhancements, improvements,
and other changes to its products and services at any time and to discontinue any product or service without notice. Customers should
obtain the latest relevant information before placing orders and should verify that such information is current and complete. All products are
sold subject to TI’s terms and conditions of sale supplied at the time of order acknowledgment.
TI warrants performance of its hardware products to the specifications applicable at the time of sale in accordance with TI’s standard
warranty. Testing and other quality control techniques are used to the extent TI deems necessary to support this warranty. Except where
mandated by government requirements, testing of all parameters of each product is not necessarily performed.
TI assumes no liability for applications assistance or customer product design. Customers are responsible for their products and
applications using TI components. To minimize the risks associated with customer products and applications, customers should provide
adequate design and operating safeguards.
TI does not warrant or represent that any license, either express or implied, is granted under any TI patent right, copyright, mask work right,
or other TI intellectual property right relating to any combination, machine, or process in which TI products or services are used. Information
published by TI regarding third-party products or services does not constitute a license from TI to use such products or services or a
warranty or endorsement thereof. Use of such information may require a license from a third party under the patents or other intellectual
property of the third party, or a license from TI under the patents or other intellectual property of TI.
Reproduction of TI information in TI data books or data sheets is permissible only if reproduction is without alteration and is accompanied
by all associated warranties, conditions, limitations, and notices. Reproduction of this information with alteration is an unfair and deceptive
business practice. TI is not responsible or liable for such altered documentation. Information of third parties may be subject to additional
restrictions.
Resale of TI products or services with statements different from or beyond the parameters stated by TI for that product or service voids all
express and any implied warranties for the associated TI product or service and is an unfair and deceptive business practice. TI is not
responsible or liable for any such statements.
TI products are not authorized for use in safety-critical applications (such as life support) where a failure of the TI product would reasonably
be expected to cause severe personal injury or death, unless officers of the parties have executed an agreement specifically governing
such use. Buyers represent that they have all necessary expertise in the safety and regulatory ramifications of their applications, and
acknowledge and agree that they are solely responsible for all legal, regulatory and safety-related requirements concerning their products
and any use of TI products in such safety-critical applications, notwithstanding any applications-related information or support that may be
provided by TI. Further, Buyers must fully indemnify TI and its representatives against any damages arising out of the use of TI products in
such safety-critical applications.
TI products are neither designed nor intended for use in military/aerospace applications or environments unless the TI products are
specifically designated by TI as military-grade or "enhanced plastic." Only products designated by TI as military-grade meet military
specifications. Buyers acknowledge and agree that any such use of TI products which TI has not designated as military-grade is solely at
the Buyer's risk, and that they are solely responsible for compliance with all legal and regulatory requirements in connection with such use.
TI products are neither designed nor intended for use in automotive applications or environments unless the specific TI products are
designated by TI as compliant with ISO/TS 16949 requirements. Buyers acknowledge and agree that, if they use any non-designated
products in automotive applications, TI will not be responsible for any failure to meet such requirements.
Following are URLs where you can obtain information on other Texas Instruments products and application solutions:
Products
Amplifiers
Data Converters
DSP
Clocks and Timers
Interface
Logic
Power Mgmt
Microcontrollers
RFID
RF/IF and ZigBee® Solutions
amplifier.ti.com
dataconverter.ti.com
dsp.ti.com
www.ti.com/clocks
interface.ti.com
logic.ti.com
power.ti.com
microcontroller.ti.com
www.ti-rfid.com
www.ti.com/lprf
Applications
Audio
Automotive
Broadband
Digital Control
Medical
Military
Optical Networking
Security
Telephony
Video & Imaging
Wireless
www.ti.com/audio
www.ti.com/automotive
www.ti.com/broadband
www.ti.com/digitalcontrol
www.ti.com/medical
www.ti.com/military
www.ti.com/opticalnetwork
www.ti.com/security
www.ti.com/telephony
www.ti.com/video
www.ti.com/wireless
Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265
Copyright © 2008, Texas Instruments Incorporated