A616316 Series Preliminary 64K X 16 BIT HIGH SPEED CMOS SRAM Document Title 64K X 16 BIT HIGH SPEED CMOS SRAM Revision History Rev. No. 0.0 PRELIMINARY History Issue Date Remark Initial issue July 14, 2000 Preliminary (July, 2000, Version 0.0) AMIC Technology, Inc. A616316 Series Preliminary 64K X 16 BIT HIGH SPEED CMOS SRAM Features n n n n n n n n n Center power pinout Supply voltage: 5V±10% Access times: 12/15 ns (max.) Current: Operating: -12: 170mA (max.) -15: 165mA (max.) Standby: TTL: 25mA (max.) CMOS: 8mA (max.) Full static operation, no clock or refreshing required All inputs and outputs are directly TTL-compatible Common I/O using three-state output Data retention voltage: 3V (min.) Available in 44-pin 400mil SOJ and 44-pin 400mil TSOP(II) forward packages. General Description The chip enable input is provided for POWER-DOWN, to disable the device. Two byte enable inputs and an output enable input are included for easy interfacing. Data retention is guaranteed at a power supply voltage as low as 3V. The A616316 is a high speed 1,048,576-bit static random access memory organized as 65,536 words by 16 bits and operates on supply voltage 5V. It is built using AMIC’s high performance CMOS process. Inputs and three-state outputs are TTL compatible and allow for direct interfacing with common system bus structures. Pin Configuration n SOJ / TSOP(II) (July, 2000, Version 0.0) 1 44 A15 A1 2 43 A14 A2 3 42 A13 A3 4 41 OE A4 5 40 HB CE 6 39 LB I/O0 7 38 I/O15 I/O1 8 37 I/O14 I/O2 9 36 I/O13 I/O3 10 35 I/O12 VCC 11 34 GND GND 12 33 VCC I/O4 13 32 I/O11 I/O5 14 31 I/O10 I/O6 15 30 I/O9 I/O7 16 29 I/O8 WE 17 28 NC A5 18 27 A12 A6 19 26 A11 A7 20 25 A10 A8 21 24 A9 NC 22 23 NC A616316S(V) PRELIMINARY A0 1 AMIC Technology, Inc. A616316 Series Block Diagram VCC A0 GND 1,048,576-BIT DECODER MEMORY ARRAY A14 A15 I/O0 I/O8 INPUT COLUMN I/O DATA DATA CIRCUIT CIRCUIT I/O15 I/O7 CE LB HB OE WE PRELIMINARY INPUT CONTROL CIRCUIT (July, 2000, Version 0.0) 2 AMIC Technology, Inc. A616316 Series Pin Description - SOJ/TSOP(II) Pin No. Symbol Description 1 - 5, 18 - 21, 24 - 27,42 - 44 A0 - A15 6 CE Chip Enable Input 7 - 10, 13 - 16, 29 - 32, 35 - 38 I/O0 - I/O15 Data Input/Outputs 17 WE Write Enable Input 39 LB Byte Enable Input (I/O0 to I/O7) 40 HB Byte Enable Input (I/O8 to I/O15) 41 OE Output Enable Input 11, 33 VCC Power 12, 34 GND Ground 22 , 23, 28 NC Address Inputs No Connection Recommended DC Operating Conditions (TA = 0°C to + 70°C) Symbol Parameter Min. Typ. Max. Unit 4.5 5.0 5.5 V 0 0 0 V VCC Supply Voltage GND Ground VIH Input High Voltage 2.2 - VCC + 0.3 V VIL Input Low Voltage -0.3 - 0.8 V CL Output Load - - 30 pF PRELIMINARY (July, 2000, Version 0.0) 3 AMIC Technology, Inc. A616316 Series Absolute Maximum Ratings* *Comments VCC to GND . . . . . . . . . . . . . . . . . . . . . . -0.5V to +7.0V IN, IN/OUT Volt to GND . . . . . . . . -0.5V to VCC + 0.5V Operating Temperature, Topr . . . . . . . . . . 0°C to +70°C Storage Temperature, Tstg . . . . . . . . . -55°C to +125°C Power Dissipation, PT . . . . . . . . . . . . . . . . . . . . . . 1.0W Soldering Temp. & Time . . . . . . . . . . . . 260°C, 10 sec Stresses above those listed under "Absolute Maximum Ratings" may cause permanent damage to this device. These are stress ratings only. Functional operation of this device at these or any other conditions above those indicated in the operational sections of this specification is not implied or intended. Exposure to the absolute maximum rating conditions for extended periods may affect device reliability. DC Electrical Characteristics (TA = 0°C to + 70°C, VCC = 5V±10%, GND = 0V) Symbol Parameter A616316-12 A616316-15 Min. Max. Min. Max. Unit Conditions ILI Input Leakage - 2 - 2 µA VIN = GND to VCC ILO Output Leakage - 2 - 2 µA CE = VIH, OE = VIH VI/O = GND to VCC Dynamic Operating Current - 170 - 165 mA CE = VIL, II/O = 0 mA Min. Cycle, Duty = 100% - 25 - 25 mA - 8 - 8 mA ICC1 (2) ISB ISB1 Standby Power Supply Current CE = VIH CE ≥ VCC - 0.2V, VIN ≥ VCC -0.2V or VIN ≤ 0.2V VOL Output Low Voltage - 0.4 - 0.4 V IOL = 8 mA VOH Output High Voltage 2.4 - 2.4 - V IOH = -4 mA Notes: 1. VIL = -3.0V for pulses less than 20 ns. 2. ICC1 is dependent on output loading, cycle rates, and Read/Write patterns. PRELIMINARY (July, 2000, Version 0.0) 4 AMIC Technology, Inc. A616316 Series Truth Table I/O0 to I/O7 Mode I/O8 to I/O15 Mode VCC Current CE OE WE LB HB H X X X X Not selected Not selected ISB1, ISB L L Read Read ICC1, ICC2, ICC L H Read High - Z ICC1, ICC2, ICC H L High - Z Read ICC1, ICC2, ICC L L Write Write ICC1, ICC2, ICC L H Write Not Write/Hi - Z ICC1, ICC2, ICC H L Not Write/Hi - Z Write ICC1, ICC2, ICC L X High - Z High - Z ICC1, ICC2, ICC X L High - Z High - Z ICC1, ICC2, ICC H H Not selected L L L L X H X X H L H X Not selected ISB1, ISB Note: X = H or L Capacitance (TA = 25°C, f = 1.0MHz) Symbol Parameter Min. Max. Unit Conditions CIN* Input Capacitance - 6 pF VIN = 0V CI/O* Input/Output Capacitance - 8 pF VI/O = 0V * These parameters are sampled and not 100% tested. PRELIMINARY (July, 2000, Version 0.0) 5 AMIC Technology, Inc. A616316 Series AC Characteristics (TA = 0°C to +70°C, VCC = 5V±10%) Symbol A616316-12 Parameter A616316-15 Unit Min. Max. Min. Max. 12 - 15 - ns Read Cycle tRC Read Cycle Time tAA Address Access Time - 12 - 15 ns tACE Chip Enable Access Time - 12 - 15 ns tOE Output Enable to Output Valid - 6 - 8 ns tCLZ Chip Enable to Output in Low Z 3 - 3 - ns tOLZ Output Enable to Output in Low Z 0 - 0 - ns tCHZ Chip Disable Output in High Z 0 6 - 8 ns tOHZ Output Disable to Output in High Z 0 6 0 8 ns tOH Output Hold from Address Change 3 - 3 - ns Write Cycle tWC Write Cycle Time 12 - 15 - ns tCW Chip Enable to End of Write 10 - 12 - ns tAS Address Setup Time of Write 0 - 0 - ns tAW Address Valid to End of Write 10 - 12 - ns tWP Write Pulse Width 10 - 12 - ns tWR Write Recovery Time 0 - 0 - ns tWHZ Write to Output in High Z 0 6 0 8 ns tDW Data to Write Time Overlap 6 - 7 - ns tDH Data Hold from Write Time 0 - 0 - ns tOW Output Active from End of Write 3 - 3 - ns Notes: tCHZ, tOHZ and tWHZ are defined as the time at which the outputs achieve the open circuit condition and are not referred to output voltage levels. PRELIMINARY (July, 2000, Version 0.0) 6 AMIC Technology, Inc. A616316 Series Timing Waveforms (1, 2, 4) Read Cycle 1 tRC Address tAA tOH tOH DOUT (1, 2, 3) Read Cycle 2 tRC Address tAA CE tACE tCHZ 5 tCLZ 5 tBE HB, LB tBLZ 5 tBHZ 5 OE tOHZ 5 tOE tOLZ 5 DOUT Notes: 1. WE is high for Read Cycle. 2. Device is continuously enabled CE = VIL, HB = VIL and, or LB = VIL. 3. Address valid prior to or coincident with CE and ( HB and, or LB ) transition low. 4. OE = VIL. 5. Transition is measured ±500mV from steady state. This parameter is sampled and not 100% tested. PRELIMINARY (July, 2000, Version 0.0) 7 AMIC Technology, Inc. A616316 Series Timing Waveforms (continued) Write Cycle 1 (Write Enable Controlled) tWC Address tWR3 tAW tCW CE tBW HB, LB tAS1 tWP2 WE tDW tDH DATA IN tWHZ 4 tOW DATA OUT PRELIMINARY (July, 2000, Version 0.0) 8 AMIC Technology, Inc. A616316 Series Timing Waveforms (continued) Write Cycle 2 (Chip Enable Controlled) tWC Address tAW tAS1 tWR3 tCW2 CE tBW HB, LB tWP WE tDW tDH DATA IN tWHZ 4 tOW DATA OUT PRELIMINARY (July, 2000, Version 0.0) 9 AMIC Technology, Inc. A616316 Series Timing Waveforms (continued) Write Cycle 3 (Byte Enable Controlled) tWC Address tAW tCW CE tAS1 tWR3 tBW2 HB, LB tWP WE tDH tDW DATA IN tWHZ 4 tOW DATA OUT Notes: 1. tAS is measured from the address valid to the beginning of Write. 2. A Write occurs during the overlap (tWP, tBW) of a low CE , WE and ( HB and, or LB ). 3. tWR is measured from the earliest of CE or WE or ( HB and, or LB ) going high to the end of the Write cycle. 4. OE level is high or low. 5. Transition is measured ±500mV from steady state. This parameter is sampled and not 100% tested. PRELIMINARY (July, 2000, Version 0.0) 10 AMIC Technology, Inc. A616316 Series AC Test Conditions Input Pulse Levels 0V to 3.0V Input Rise And Fall Time 3 ns Input and Output Timing Reference Levels 1.5 V Output Load See Figures 1 and 2 5V 480Ω I/O OUTPUT RL=50Ω ZO=50Ω 255Ω 5pF* VT=1.5V * Including scope and jig. Figure 1. Output Load Figure 2. Output Load for tCLZ, tOLZ, tCHZ, tOHZ, tWHZ, and tOW Data Retention Characteristics (TA = 0°C to 70°C) Symbol VDR Parameter VCC for Data Retention Min. Max. Unit 3 5.5 V ICCDR Data Retention Current - 1 mA tCDR Chip Disable to Data Retention Time 0 - ns tR Operation Recovery Time Conditions CE ≥ VCC - 0.2V VCC = 3.0V CE ≥ VCC - 0.2V VIN ≥ VCC - 0.2V or VIN ≤ 0.2V See Retention Waveform TRC* - ms tRC = Read Cycle Time PRELIMINARY (July, 2000, Version 0.0) 11 AMIC Technology, Inc. A616316 Series Low VCC Data Retention Waveform DATA RETENTION MODE VCC 4.5V 4.5V tCDR tR VDR ≥ 3V tVR VIH CE VIH CE ≥ VDR - 0.2V Ordering Information Part No. Access Time (ns) Operating Current Max. (mA) CMOS Standby Max. (mA) 12 120 8 A616316S-12 44L SOJ A616316V-12 44L TSOP(II) A616316S-15 44L SOJ 15 100 A616316V-15 PRELIMINARY Package 8 44L TSOP(II) (July, 2000, Version 0.0) 12 AMIC Technology, Inc. A616316 Series Package Information SOJ 44L Outline Dimensions unit: inches/mm D 23 1 22 E1 44 A A1 A2 C E b b1 Min 0.025" y D e Seating Plane Symbol 0.004 Dimensions in inches E2 R1 y Dimensions in mm Min Nom Max Min Nom Max A 0.128 0.138 0.148 3.25 3.51 3.76 A1 0.082 - - 2.08 - - A2 0.105 0.110 0.115 2.67 2.79 2.92 0.51 b 0.015 - 0.020 0.38 - b1 0.026 0.028 0.032 0.66 0.71 0.81 C 0.007 - 0.013 0.18 - 0.21 D 1.120 1.125 1.130 28.45 28.58 28.70 E 0.435 0.440 0.445 11.05 11.18 11.30 E1 0.394 0.400 0.405 10.01 10.16 10.29 E2 0.370 BSC e R1 θ 9.40 BSC 0.050 BSC 0.030 0.035 0° - θ 1.27 BSC 0.040 10° 0.76 0.89 1.02 0° - 10° Notes: 1. The maximum value of dimension D includes end flash. 2. Dimension E does not include resin fins. 3. Dimension E1 is for PC Board surface mount pad pitch design reference only. PRELIMINARY (July, 2000, Version 0.0) 13 AMIC Technology, Inc. A616316 Series Package Information TSOP 44L (Type II) Outline Dimensions unit: inches/mm E E1 44 θ L L1 1 L A2 A1 e D b A c D ZD L1 y Dimensions in inches Dimensions in mm Symbol Min Nom Max Min Nom Max A - - 0.047 - - 1.20 A1 0.002 - 0.006 0.05 - 0.15 A2 0.037 0.039 0.041 0.95 1.00 1.05 b 0.012 - 0.018 0.30 - 0.45 c 0.005 - 0.008 0.12 - 0.21 D 0.720 0.725 0.730 18.28 18.41 18.54 ZD E 0.032 REF 0.805 REF 0.455 0.463 0.471 11.56 11.76 11.96 E1 0.395 0.400 0.405 10.03 10.16 10.29 L 0.019 0.023 0.027 0.49 0.59 0.69 L1 0.031 REF e 0.80 REF 0.031 BSC 0.80 BSC y - - 0.004 - - 0.10 θ 0° - 5° 0° - 5° Notes: 1. The maximum value of dimension D includes end flash. 2. Dimension E1 does not include resin fins. 3. Dimension ZD includes end flash. PRELIMINARY (July, 2000, Version 0.0) 14 AMIC Technology, Inc.